2015 Mitsubishi Outlander Sport TSBs

system for affected vehicles.

complains that the engine will not start while using the remote start system.

quantity of mounting bolts for vehicles equipped with 4B1 series engine. (Service Manual Revision)

affected vehicles with improved countermeasure parts. Due to a change in the reclining motor, the new longer harness and connector are necessary.

affected vehicles with improved countermeasure parts. Due to a change in the reclining motor, the new longer harness and connector are necessary.

of absorbers unnecessarily when trace amounts of oil are noted to have adhered to the shock absorber.

dcondition at low speeds (10-40 mph) or a surge/flare of engine rpm at higher speeds. This may be caused by a malfunctioning of the CVT's hydraulic pressure control software. In the worst case scenario, with continued driving under these conditions, the CVT belt may become damaged and cause a warning light to turn on.

to a customer concern of oil leaking.

communication error that may occur between the One-Touch Start System (OSS) and Engine Control Unit (ECU) or the Keyless Operating System (KOS) and Engine Control Unit (ECU).

setting of the solenoid valve voltage monitoring circuit.

Exhaust Manifold and instructs dealers to replace the Heat Protector Assembly with a new part.

found at the hose connection and to replace the old hose clamp with a countermeasure clamp and to replace the old water hose with a new water hose.

found at the hose connection and to replace the old hose clamp with a countermeasure clamp and to replace the old water hose with a new water hose.

- July 2020

and MY 2020-2018 Outlander Sports with 2.4L engines.

repair and maintenance procedures.

This Bulletin updates the Body section of the affected Service Manual to add a Caution to the installation service points of the TPMS valve (rubber snap-in type only).

The bulletin instructs dealers to confirm a list of specific Diagnostic Trouble Codes (DTCs) if vehicle experiences the following symptoms in cold weather: the check engine light illuminating with a limited vehicle speed (failsafe mode), or the engine does not restart after driving a short distance and stopping the engine for a few minutes. Once symptoms and DTCs are confirmed, dealers should replace the following relays with anti- freezing types: ETV, A/T (CVT), injector, and starter. This bulletin supersedes TSB-18-13-003, issued December, 2018, to add Eclipse Cross, applicable Canadian models, and countermeasure dates.

This Bulletin updates the Body section of the affected Service Manual to add a Caution to the installation service points of the TPMS valve (rubber snap-in type only).

The bulletin instructs dealers to confirm a list of specific Diagnostic Trouble Codes (DTCs) if vehicle experiences the following symptoms in cold weather: the check engine light illuminating with a limited vehicle speed (failsafe mode), or the engine does not restart after driving a short distance and stopping the engine for a few minutes. Once symptoms and DTCs are confirmed, dealers should replace the following relays with anti- freezing types: ETV, A/T (CVT), injector, and starter. This bulletin supersedes TSB-18-13-003, issued December, 2018, to add Eclipse Cross, applicable Canadian models, and countermeasure dates.

The bulletin updates the Automatic Transmission section of the affected Service Manual, to make corrections to the replacement procedures for the CVT assembly and valve body assembly.

This bulletin instructs dealers to how to fix a condition of a metallic knocking sound coming from the rear brakes. Affected vehicles experience this condition when the brake is applied while driving at low speeds, or on driving on uneven roads. Dealers are instructed to replace the rear brake pad clips (upper and lower) with new parts on affected vehicles, and to apply grease between the brake pad and caliper support.

The bulletin instructs dealers to confirm a list of specific Diagnostic Trouble Codes (DTCs) if vehicle experiences the following symptoms in cold weather: the check engine light illuminating with a limited vehicle speed (failsafe mode), or the engine does not restart after driving a short distance and stopping the engine for a few minutes. Once symptoms and DTCs are confirmed, dealers should replace the following relays with anti- freezing types: ETV, A/T (CVT), injector, and starter.

WIPER MOTOR CONNECTOR'S CONDITIONS, AND WIPER LINK BOOTS.

THE PARTS BEING STUDIED MUST ALSO BE SHIPPED TO MMNA FOR EXAMINATION.

MISSING EXHAUST MANIFOLD SUPPORT BRACKET.

CVT ASSEMBLY OR CVT−ECU (ECU) IS REPLACED.

of engine rpm at higher speeds. This may be caused by a malfunctioning of the CVTs hydraulic pressure control software. In the worst case scenario, with continued driving under these conditions, the CVT belt may become damaged and cause a warning light to turn on.

This may be caused by a malfunctioning of the CVTs hydraulic pressure control software. In the worst case scenario, with continued driving under these conditions, the CVT belt may become damaged and cause a warning light to turn on. Your local Mitsubishi dealer will reprogram the transmission control module (TCM). This repair will take from 0.3 to 0.6 hours to complete. In extreme cases, the transmission may need to be replaced. This repair will take approximately 6.8 to 8.2 hours. However, the dealer may need your vehicle for a longer period of time due to scheduling. Every effort will be made to minimize your inconvenience. Product improvements will be completed free of charge.

PISTON SCUFF, DAYTIME RUNNING LIGHT OR INTAKE AND EXHAUST SYSTEM OR REPLACEMENT OF REAR AXLE ASSEMBLY. VARIOUS MODEL YEARS AND VEHICLES. *PE

It covers various topics and reviews the previous months publications.

It covers various topics and reviews the previous months publications.

residue.

capacity be affixed to vehicles when the total net weight of accessories is more than 1.5 percent of the vehicle's gross vehicle weight rating (GVWR) or 100 lbs.

is an expansion of Recall SR-20-003.

Crossmembers.

Added Warranty information for instances where subframe may fail and cause additional damage to unrelated parts. This bulletin provides directions for inspection and repair of affected vehicles' Crossmembers.

Added Warranty information for instances where subframe may fail and cause additional damage to unrelated parts. This bulletin provides directions for inspection and repair of affected vehicles' Crossmembers.

It covers various topics and reviews the previous months publications.

they will be notified when parts become availble for repairs to begin. This notice also provided customers instruction on how to obtain repairs.

with shudder/surge condition and/or DTC.

ADD 2.4L POWERTRAIN TECHNICAL SPECIFICATIONS.

VEHICLE INCLUDED IN BOTH SC-15-003 AND SR-16-006.

THE REVISED SERVICE CAMPAIGN BULLETIN INCLUDES INSTRUCTIONS THAT DEALERS NEED TO FOLLOW WHEN ENCOUNTERING A VEHICLE INCLUDED IN BOTH SC-15-003 AND SR-16-006.

connection when certain devices are connected to WiFi.

exhibiting a shudder or surge condition possibly caused by poor reaction of the hydraulic pressure circuit.

exhibiting a shudder or surge condition possibly caused by poor reaction of the hydraulic pressure circuit.

affected vehicles with improved countermeasure parts.

B1B8C "Driver's Seat slide sensor open circuit " Additional OCM DTC that may also be present are: B1B8C "Drive's seat slide sensor curcuit Performance, "and B1B8E "Driver's seat slide sensor short circuit"

Circuits may appear and dealers should check for damage to the drivers seat slide position sensor harness.

disassembly procedure of the front seat assembly with these additional parts: Seat heater harness, Front seat hinge protector, and Slide sensor harness.

This bulletin provides dealers with a basic description of the hands-free systems used in Mitsubishi built vehicles. The bulletin covers components and operation, system layouts showing the differences in Japan built and U.S. built vehicles, diagnostic flow charts, a list of commonly used acronyms and terms, and part numbers. The bulletin also provides a comprehensive Hands-free/FUSE Information Sheet to guide the service writer in getting complete and accurate details from the customer. With this information, dealer personnel can answer questions and conduct an efficient diagnosis to resolve customer concerns as quickly as possible.

This bulletin provides dealers with a basic description of the hands-free systems used in Mitsubishi built vehicles. The bulletin covers components and operation, system layouts showing the differences in Japan built and U.S. built vehicles, diagnostic flow charts, a list of commonly used acronyms and terms, and part numbers. The bulletin also provides a comprehensive Hands-free/FUSE Information Sheet to guide the service writer in getting complete and accurate details from the customer. With this information, dealer personnel can answer questions and conduct an efficient diagnosis to resolve customer concerns as quickly as possible.

This bulletin updates the Chassis Electrical section of the affected Service Manuals to update diagnostics for ETACS-ECU CAN timeout diagnostics with DTC U0141.

This bulletin updates the Supplemental Restraint System (SRS) section of the affected Service Manuals to update diagnostics for ETACS-ECU CAN timeout diagnostics with DTC U0141.

This bulletin updates the Body section of the affected Service Manuals to update diagnostics for ETACS-ECU CAN timeout with DTC U0141.

It provides dealers instructions for reprogramming the ETACS ECU with updated software to resolve the issue on certain vehicles experiencing dome light flickering when the vehicle's doors are opened or dome light is switched to "ON."

This notice informs dealers how to address stored DTCs (including P0657) in extremely cold ambient temperatures. Dealers can remedy this by replacing the throttle actuator control (TAC) relay.

MAY EXHIBIT A CONDITION WHERE THE IGNITION CANNOT BE TURNED OFF WHEN BATTERY VOLTAGE DROPS. THIS TSB ALSO INCLUDES INSTRUCTION FOR DEALERS TO PROVIDE EXPLANATIONS TO CUSTOMERS REGARDING SYMPTOMS DUE TO LOW BATTERY VOLTAGE AND THAT BATTERY VOLTAGE SHOULD BE CHECKED AS PART OF ROUTINE VEHICLE MAINTENANCE.

THE AFFECTED SERVICE MANUALS TO ADD A WARNING TO CHECK OCCUPANT CLASSIFICATION SENSOR ACCURACY DURING FRONT SEAT REMOVAL AND INSTALLATION.

to install the oil seal within the Automatic Transaxle sections of the applicable Service Manuals.

on-vehicle service for belt & pulley assembly on certain CVT models.

(Service Manual Revision)

F1CJC/W1CJC (CVT-8) transmissions that may exhibit a shudder or surge condition possibly caused by a poor reaction of the hydraulic pressure circuit.

reaction of the hydraulic pressure circuit. With continued driving under these conditions, the CVT belt may slip repeatedly when accelerating, and abrasion powder may enter the hydraulic pressure circuit, causing a warning light to turn on. This TSB instructs dealers to diagnose and test drive vehicles exhibiting this condition. *This TSB may also apply to later model years with F1CJC/W1CJC (CVT-8) transmissions.

the affected Service Manuals, to correct general information for the CVT lock-up control.

This bulletin updates the Rear Axle section of the affected Service Manuals, to correct the quantity of rear differential gear oil used.

This bulletin updates the Automatic Transaxle section of the affected Service Manuals, to correct the torque converter pressure in the standard hydraulic pressure table.

The bulletin updates the Automatic Transmission section of the affected Service Manual, to include steps for the shift indicator panel removal and installation procedure.

The bulletin updates the Automatic Transmission section of the affected Service Manuals, to include additional service parts for the transaxle removal and installation procedure. This bulletin also informs dealers that the applicable parts were made available in May 2015.

stumble or lack of acceleration at low speeds. Dealers were advised to inspect the Transmission Range Switch and Control Cable Adjustment if a customer reported experiencing this condition.

Assembly had been placed on "209" order restriction.

Variable Transmission.

MANUALS TO CORRECT THE CLAMPING TORQUE OF STEERING GEAR AND LINKAGE IN FRONT CROSSMEMBER REMOVAL AND INSTALLATION.

Windshield Wiper in the Exterior portion of the affected Service Manuals.

a natural phenomenon, and water penetration caused by improper sealing or a defective/broken part.

(SR-20-003) for the Crossmember Corrosion.

(SR-20-003) for the Crossmember Corrosion.

the inside and outside surfaces of the front cross members used on certain vehicles, if exposed long term to snow melt water and anti-freezing agents, may corrode due to insufficient performance of the rust protection.

manuals.

This TSB instructs dealers to submit photos to the PRC of any rusted areas, repair affected areas, add sufficient sealant to prevent rust, repaint repaired areas, then apply protective film on the open switch area.

This bulletin updates the Body section of the affected Service Manual, to correct the tightening torque for the liftgate removal and installation procedure, and to correct a non-reusable part indicator.

This bulletin updates the Body section of the affected Service Manual, to correct the tightening torque for the liftgate removal and installation procedure, and to correct a non-reusable part indicator.

This bulletin instructs dealers how to re-register vehicle keys for affected vehicles. Affected vehicles may experience a condition of the door(s) inability to be locked or unlocked using the Remote Keyless Entry (RKE) function. Dealers are instructed to re- register the ley using "Customer Key Programming" procedure in the Owner's Manual. This bulletin also provides Summary Table for Function Customization & Key Programming.

The bulletin updates the Body section of the affected Service Manuals to add the type of the hood latch mounting bolt and to correct the tightening torque for the hood.

possible rust areas and to require photos of the affected areas.

CHANNELS, IF THERE ARE DOOR GLASS CHATTER OR BINDING DURING OPERATION.

technician quiz for 2023.

technician quiz for 2023.

beginning with Model Year 2015.

and repair procedure; noting when a Crossmember replacement is required the anti-corrosive agent application is not required.

and repair procedure; noting when a Crossmember replacement is required the anti-corrosive agent application is not required.

railroad tracks, highway lane markers ("Botts dots") or rough road surfaces. This may be caused by contact between the glovebox and the dash. This TSB instructs technicians to remove the existing glovebox felt insulating strips and add a new felt strip in a different location to suppress the noise.

MODEL 2015 OUTLANDER SPORT. *PE

the Service Brakes portion of the affected Service Manuals.

when customers report a condition where an abnormal rubbing noise is heard from the Seat Back when a driver and/or passenger is seated in the front seat(s).

rear end portion of the seat cushion by a passenger, the cushion may sink down and rub against the edges of the metal seat frame. This in turn may cause the damaged urethane material to turn to powder and fall on the floor carpet. This TSB provides a repair procedure to replace the damaged seat cushion pad, and apply tape on the frame to help prevent future damage.

This bulletin updates the Rear Suspension section of the affected Service Manuals, to delete the requirement for an installation direction of the coil spring end of the shock absorber assembly.

This bulletin updates the Rear Suspension section of the affected Service Manuals, to delete the requirement for an installation direction of the coil spring end of the shock absorber assembly.

IPHONE/IPOD/IPAD WHEN THE DEVICE IS CONNECTED TO WI‐FI. THIS UPDATE ADDRESSES UNSTABLE, REPEATEDLY CONNECTING AND DISCONNECTING FROM THE VEHICLE'S BLUETOOTH WHEN THE IPHONE'S WI‐FI IS ENABLED. THE CONDITION DOES NOT OCCUR WHEN WI‐FI IS TURNED OFF.

2014 - 2016 OUTLANDER SPORT VEHICLES WILL BE PLACED ON 209 RESTRICTION EFFECTIVE IMMEDIATELY. TECHNICIANS MUST REFER TO THE PROCEDURES IN TECH TALK 223 AND TSB-16-35-001 BEFORE ORDERING A REPLACEMENT ABS HYDRAULIC UNIT. TECHNICIANS MUST CONTACT TECHLINE TO HAVE THE PART ORDER RELEASED.

AFFECTED MODELS' SERVICE MANUALS.

update regarding warranty information and entry of claims.

information.

update regarding warranty information and entry of claims.

information.

This bulletin supersedes TSB-18-00-003, issued April, 2018, to add updated information for Carrying Capacity Reduced Label.

tongue not staying in place or that slides down to the floor, always default to searching for applicable TSBs, Tech Talk articles, and TINs first.

Supplemental Restraint System (SRS) section of the affected Service Manuals, to correct the front pillar trim assembly installation procedure.

This bulletin updates the Supplemental Restraint System (SRS) section of the affected Service Manuals, to correct minor errors in the diagnosis for DTC B1631.

Customers may report the front seat belt fraying as a result of being caught under the seat reclining adjusting lever. This TSB instructs dealers how to replace the front seat belt and reclining adjusting lever (driver and/or passenger side) with a countermeasure part, to prevent fraying of the seat belt should it get caught under the lever, on affected vehicles.

STOPPER BUTTONS.

OTHER MODELS' SERVICE MANUALS ARE UPDATED WITH INFORMATION FOR THE OUTER SEAT BELT ON THE FRONT PASSENGER'S SIDE SEAT TO CLARIFY THE FRONT SEAT BELT INSTALLATION AND REMOVAL PROCEDURE.

when customers report a condition in vehicles equipped with a front wheel arch molding displays a gap between the front wheel arch molding and the fender.

speakers in Mitsubishi vehicles equipped with original equipment audio components.

It provides dealers instructions for resolving customer's report that Bluetooth pairing code given by the Hands Free Link system does not work for certain smartphone models, namely, Samsung Galaxy and Sony Xperia. For these smartphone models, the pairing code for Bluetooth connection must be set to a fixed code of ?0000.? This TSB instructs dealers how to register these smartphones using the pairing code ?0000.?

RECOGNITION TO COMPLETE BEFORE CONNECTION TO THE PHONE BEGINS, TO RECTIFY THE CONDITION WHERE THE HFM ATTEMPTS A BLUETOOTH CONNECTION WITH A MOBILE PHONE WHILE VOICE RECOGNITION IS BOOTING AT THE SAME TIME. IF THE BLUETOOTH CONNECTION COMPLETES BEFORE VOICE RECOGNITION COMPLETES, VOICE RECOGNITION CANNOT BE USED.

CERTAIN EXHAUST FASTENERS.

SEVERAL OF EXHAUST PIPE HEATSHIELD COMPONENTS NOW AVAILABLE AS SERVICE PARTS.

SEVERAL OF THE EXHAUST PIPE HEAT SHIELD COMPONENTS ARE NOW AVAILALBE AS SERVICE PARTS. WHEN REPAIRING A VEHICLE FOR A NOISE DUE TO A LOOSE HEAT SHIELD, DO NOT REPLACE THE CENTER EXHAUST PIPE WITH CATALYTIC CONVERTOR IF THE HEAT SHIELD CAN BE SERVICED SEPARATELY.

(Service Manual Revision)

The bulletin updates the Front Suspension section of the affected Service Manuals to correct the starting torque of the Lower Arm Ball Joint rotation.

The bulletin updates the Front Suspension section of the affected Service Manuals to update the special service tool used in replacement of the Lower Arm Ball Joint Dust Cover.

parts availability delay of the Crossmember, customer vehicles requiring a replacement of the crossmember are unable to be completed at this time. Additionally, this notice informed dealers that an Interim Owner Notification Letter was mailed to affected owners on July 17th, 2020 to inform customers that MMNA is making every effort to establish a remedy and will contact them again by mail with a follow-up recall notice once parts are in stock and the final remedy is available.

parts availability delay of the Crossmember, customer vehicles requiring a replacement of the crossmember are unable to be completed at this time. Additionally, this notice informed dealers that an Interim Owner Notification Letter was mailed to affected owners on July 17th, 2020 to inform customers that MMNA is making every effort to establish a remedy and will contact them again by mail with a follow-up recall notice once parts are in stock and the final remedy is available.

MODELS ONLY), INCLUDING THE NEW 2.4L ES AND GT MODELS.

TSB-17-52A-003, to add Outlander PHEV and additional model years for Outlander and Outlander Sport, and to update parts and procedures to help resolve the power seat movement.

issued January 2019, to update symptoms in the Purpose section, and to remove Outlander PHEV from the Affected Vehicles.