2014 Mitsubishi Mirage TSBs

the affected Service Manuals and advises of new flange bolts available for use.

of absorbers unnecessarily when trace amounts of oil are noted to have adhered to the shock absorber.

This is a drefsult of higher than expected demand resulting from diagnosis of the knocking noise as outlined in the Service Campaign Bulletin.

February, 2016 to add a Code 209 Restriction on new engines, detailed procedures required by dealers before ordering a new engine, and a Sample customer letter. Revisions are italicized and indicated by - During cold start, the engine ECU may order inappropriate fuel amounts which may cause efangine noise.

inapprokpriate fuel amounts which may caus e engine noise. This campaign bulletin instructs dealers to reprogram the ECM with new software on all affected vehicles. In rare cases, if the vehicle exhibits an enggine knocking noise, the fengine may need to be replaced.

software on all affected vehicles. In rare cases, if the vehicle exhibits an engine knocking noise, the engine may need to be replaced.

stopping or during idling, when operated in high ambient temperature conditions, which may lead to PCV hose disconnection. If this condition were to occur, a stalled engine can immediately be restarted. This TSB instructs dealers to reprogram the ECM with new software that optimizes the air fuel ratio.

stopping or during idling, when operated in high ambient temperature conditions, which may lead to PCV hose disconnection. If this condition were to occur, a stalled engine can immediately be restarted. This TSB instructs dealers to reprogram the ECM with new software that optimizes the air fuel ratio.

The bulletin instructs dealers to confirm a list of specific Diagnostic Trouble Codes (DTCs) if vehicle experiences the following symptoms in cold weather: the check engine light illuminating with a limited vehicle speed (failsafe mode), or the engine does not restart after driving a short distance and stopping the engine for a few minutes. Once symptoms and DTCs are confirmed, dealers should replace the following relays with anti- freezing types: ETV, A/T (CVT), injector, and starter. This bulletin supersedes TSB-18-13-003, issued December, 2018, to add Eclipse Cross, applicable Canadian models, and countermeasure dates.

This notice informs dealers that Mitsubishi Motors North America (MMNA) is looking for a scramble opportunity on a Mirage or Mirage G4 that displays "TPMS light on" issue with "tire ID reception fail" DTC. If a vehicle has C1911, C1921, C1931, or C1941 active or stored then dealers are instructed to stop the diagnosis process and create a Techline case. Once a Techline case is created, dealers are referred to a MMNA associate that will provide further assistance.

The bulletin instructs dealers to confirm a list of specific Diagnostic Trouble Codes (DTCs) if vehicle experiences the following symptoms in cold weather: the check engine light illuminating with a limited vehicle speed (failsafe mode), or the engine does not restart after driving a short distance and stopping the engine for a few minutes. Once symptoms and DTCs are confirmed, dealers should replace the following relays with anti- freezing types: ETV, A/T (CVT), injector, and starter. This bulletin supersedes TSB-18-13-003, issued December, 2018, to add Eclipse Cross, applicable Canadian models, and countermeasure dates.

This notice informs dealers that Mitsubishi Motors North America (MMNA) is looking for a scramble opportunity on a Mirage or Mirage G4 that displays "TPMS light on" issue with "tire ID reception fail" DTC. If a vehicle has C1911, C1921, C1931, or C1941 active or stored then dealers are instructed to stop the diagnosis process and create a Techline case. Once a Techline case is created, dealers are referred to a MMNA associate that will provide further assistance.

The bulletin updates the Wheel and Tire section of the affected Service Manuals to add a Caution to the installation Service points of the TPMS valve.

The bulletin updates the Service Brakes section of the affected Service Manuals to add information on push rod depth adjustment during removal and installation of the brake master cylinder and brake booster assemblies.

The bulletin instructs dealers to confirm a list of specific Diagnostic Trouble Codes (DTCs) if vehicle experiences the following symptoms in cold weather: the check engine light illuminating with a limited vehicle speed (failsafe mode), or the engine does not restart after driving a short distance and stopping the engine for a few minutes. Once symptoms and DTCs are confirmed, dealers should replace the following relays with anti- freezing types: ETV, A/T (CVT), injector, and starter.

TIN-18-23-002, to state that the collection of parts requested in those documents has been completed--MMNA has now collected enough complete sets of CVT fluid coolers with hoses and clamps for a sufficient coolant investigation. Dealers are to follow the normal diagnostic and repair procedures for coolant leakage from CVT hoses.

It informs dealers of some reported coolant leaking from the transmission cooler line hoses at the CVT7 fluid cooler. The notice informs dealers that MMNA is looking to collect 5 complete sets of those CVT7 fluid coolers with the hoses and clamps undisturbed, in order for MMC to perform a duplication test to confirm the area of leakage.

PART NUMBER LISTED IN SC-16-001REV, ECM REPROGRAMMING FOR ENGINE KNOCKING NOISE FOR CERTAIN 2014 2015 MIRAGE VEHICLES.

WITH NEW SOFTWARE ON ALL AFFECTED VEHICLES, TO RECTIFY POSSIBLE ENGINE NOISE DURING COLD START.

CAMPAIGN BULLETIN WILL BE RELEASED FOR ECM REPROGRAMMING FOR ENGINE KNOCKING NOISE.

RECTIFY POSSIBLE ENGINE NOISE DURING COLD START.

2014 2015 MIRAGE VEHICLES, WHERE DURING COLD START, THE ENGINE ECU MAY ORDER INAPPROPRIATE FUEL AMOUNTS WHICH MAY CAUSE ENGINE NOISE, WILL BE FORTHCOMING. THE CAMPAIGN BULLETIN WILL INSTRUCT DEALERS TO REPROGRAM THE ECM WITH NEW SOFTWARE ON ALL AFFECTED VEHICLES, AND IN RARE CASES, IF THE VEHICLE EXHIBITS AN ENGINE KNOCKING NOISE, THE ENGINE MAY NEED TO BE REPLACED.

RATIO, IF DUE TO A RICH AIR FUEL RATIO, THE AFFECTED VEHICLES EXPERIENCE ENGINE STALLING AT LOW ENGINE SPEED, JUST PRIOR TO STOPPING OR DURING IDLING, AND WHEN OPERATED IN HIGH AMBIENT TEMPERATURE CONDITIONS.

This campaign bulletin instructs dealers to reprogram the ECM with new software on all affected vehicles. In rare cases, if the vehicle exhibits an engine knocking noise, the engine may need to be replaced.

engine, which may cause engine noise.

PISTON SCUFF, DAYTIME RUNNING LIGHT OR INTAKE AND EXHAUST SYSTEM OR REPLACEMENT OF REAR AXLE ASSEMBLY. VARIOUS MODEL YEARS AND VEHICLES. *PE

*LJ UPDATED 9/10/15. *PE UPDATED 12/2/15. *PE

MASTER CYLINDER AND ASC HYDRAULIC UNIT. *JS

THIS CAN CAUSE A NOISE WHEN THE ENGINE IS BEING STARTED. *JS

It covers various topics and reviews the previous months publications.

It covers various topics and reviews the previous months publications.

residue.

capacity be affixed to vehicles when the total net weight of accessories is more than 1.5 percent of the vehicle's gross vehicle weight rating (GVWR) or 100 lbs.

THIS NOTICE ALSO INFORMED DEALERS TO ADDRESS SAFETY RECALL SR-16-001 AT THE SAME TIME AS THIS SERVICE CAMPAIGN IN ORDER TO REDUCE POSSIBLE INCONVENIENCES.

SLIDE RAIL LOCK POSITION TIMING ON VEHICLES WHERE THE CUSTOMER REPORTS A CONDITION WHERE, AFTER ADJUSTING THE SEAT SLIDE POSITION (FORWARD OR REARWARD), ONE OF THE SEAT RAILS DOES NOT LOCK INTO POSITION WHEN THE ADJUSTER BAR IS RELEASED.

TROUBLESHOOTING.

MANUAL, FOR CRUISE CONTROL DIAGNOSTIC TROUBLE CODES.

*JS

connection when certain devices are connected to WiFi.

of the affected Service Manuals, Side Impact Sensor.

Service Manuals, Horn removal and installation.

This bulletin provides dealers with a basic description of the hands-free systems used in Mitsubishi built vehicles. The bulletin covers components and operation, system layouts showing the differences in Japan built and U.S. built vehicles, diagnostic flow charts, a list of commonly used acronyms and terms, and part numbers. The bulletin also provides a comprehensive Hands-free/FUSE Information Sheet to guide the service writer in getting complete and accurate details from the customer. With this information, dealer personnel can answer questions and conduct an efficient diagnosis to resolve customer concerns as quickly as possible.

This bulletin provides dealers with a basic description of the hands-free systems used in Mitsubishi built vehicles. The bulletin covers components and operation, system layouts showing the differences in Japan built and U.S. built vehicles, diagnostic flow charts, a list of commonly used acronyms and terms, and part numbers. The bulletin also provides a comprehensive Hands-free/FUSE Information Sheet to guide the service writer in getting complete and accurate details from the customer. With this information, dealer personnel can answer questions and conduct an efficient diagnosis to resolve customer concerns as quickly as possible.

The bulletin instructs dealers to reprogram the SRS-ECU with updated software that corrects an issue when the Supplemental Restraint System (SRS) Air Bag Warning Lamp illuminates with DTC B1479 (SRS-ECU Backup capacitor circuit voltage too Low.)

This notice informs dealers how to address stored DTCs (including P0657) in extremely cold ambient temperatures. Dealers can remedy this by replacing the throttle actuator control (TAC) relay.

a TPMS sensor claim.

(SRS) section of the affected Service Manuals to include seat slide sensor and seat belt switch information.

(SRS) section of the affected Service Manuals to update removal and installation procedures of the side airbag module.

Service Manuals to make corrections to the Torque Sensor check conditions in the Power Steering Diagnosis Data List Reference Table.

claims for TPMS sensor replacements.

CLAIMS FOR TPMS SENSOR REPLACEMENTS.

MAY EXHIBIT A CONDITION WHERE THE IGNITION CANNOT BE TURNED OFF WHEN BATTERY VOLTAGE DROPS. THIS TSB ALSO INCLUDES INSTRUCTION FOR DEALERS TO PROVIDE EXPLANATIONS TO CUSTOMERS REGARDING SYMPTOMS DUE TO LOW BATTERY VOLTAGE AND THAT BATTERY VOLTAGE SHOULD BE CHECKED AS PART OF ROUTINE VEHICLE MAINTENANCE.

INCLUDE THE SEAT SLIDE SENSOR AND UPDATED INFORMATION FOR THE SEAT BELT SWITCH CONTINUITY CHECK.

OF THE AFFECTED SERVICE MANUALS TO INCLUDE THE SEAT SLIDE SENSOR.

(SRS) SECTION OF THE TECHNICAL INFORMATION MANUAL TO INCLUDE SEAT SLIDE SENSOR INFORMATION

THE AFFECTED SERVICE MANUALS TO INCLUDE THE SEAT SLIDE SENSOR

SENSORS UNDER WARRANTY.

AFFECTED SERVICE MANUALS TO INCLUDE THE SEAT SLIDE SENSOR AND FRONT SEAT BELT SWITCH.

technician quiz for 2023.

technician quiz for 2023.

SR-16-001 REPAIRS.

shaft disassembly and assembly sections of the applicable service manuals.

Required Condition & Pre-Approval Center (PRC) for a vehicle pulling/drifting and/or with steering wheel off-center concerns.

alignment check and adjustment on an affected vehicle with a customer concern of pulling/drifting and/or steering wheel off-center concerns.

a wheel alignment check and adjustment on an affected vehicle with a customer concern of pulling/drifting and/or steering wheel off-center concerns.

photographs when performing a wheel alignment check and adjustment on an affected vehicle with a customer concern of pulling/drifting and/or steering wheel off-center concerns (while under warranty). This Notice supersedes TIN-17-37-001 released in July, 2017, to expand affected models and model years.

photographs when performing a wheel alignment check and adjustment on an affected vehicle with a customer concern of pulling/drifting and/or steering wheel off-center concerns (while under warranty).

photographs when performing a wheel alignment check and adjustment on an affected vehicle with a customer concern of pulling/drifting and/or steering wheel off-center concerns (while under warranty).

(Service Manual Revision)

This bulletin updates the Front Suspension section of the affected Service Manuals, to add information to the stabilizer bar removal and installation procedure.

This bulletin updates the Rear Suspension section of the affected Service Manual, to make updates to the rear wheel alignment check and adjustment procedures.

This bulletin updates the Front Suspension section of the affected Service Manual, to add a note that recommends that a compensator is used to measure the camber.

The bulletin updates the Front suspension section of the affected Service Manuals, to update the check and replacement procedures of the Lower Arm Ball Joint Dust Cover.

REAR WHEEL BEARING INSTALLATION ASSEMBLY SERVICE POINT, FOR SOME VEHICLES. MODEL 2014 MIRAGE. *PE

a natural phenomenon, and water penetration caused by improper sealing or a defective/broken part.

Manual, Door, Door Handle and Latch Removal and Installation.

Manual, Door.

Windshield Wiper and Washer Removal and Installation procedures.

manuals.

Service Manuals to correct the tightening torque of the door window glass and power window regulator fixing bolts.

This bulletin updates the Supplemental Restraint System (SRS) section of the affected Service Manual, to correct the Check Chart to the Diagnostic Trouble Codes (DTCs) list.

The bulletin updates the Supplemental Restraint System (SRS) section of the affected Service Manuals, to correct the description of DTC B1616 in the Check Chart for Diagnostic Trouble Codes.

The bulletin updates the Interior and Supplemental Restraint (SRS) section of the affected Service Manuals to update the Removal and Installation procedure of seat belts with pre-tensioner (seat belt anchor adjuster has been added).

Diagnosis Check Chart for Diagnostic Trouble Codes in the Service Manual.

rails does not lock into position when the adjuster bar is released. An unlocked inner or outer seat rail allows for excessive motion in the seat cushion, usually noticed when the occupant redistributes their body weight while sitting in the seat. This condition may be due to unsynchronized lock position timing between the inner and outer rail.

opportunity on a Mirage or Mirage G4 that displays ?TPMS light on? issue with ?tire ID reception fail? DTC. This TIN also supersedes TIN-19-31-001REV, issued May, 2019, to add 2020 model year Mirage and Mirage G4 vehicles, and to update MMNA contact information.

speakers in Mitsubishi vehicles equipped with original equipment audio components.

This notice informs dealers that MMNA is looking for a scramble opportunity on a Mirage or Mirage G4 that displays "TPMS light on" issue with "tire ID reception fail" DTC. If a vehicle has C1911, C1921, C1931, or C1941 active or stored then dealers are instructed to stop the diagnosis process and create a Techline case. This notice was re-released to remind all dealers to call Techline for TPMS concerns on affected models.

It provides dealers instructions for resolving customer's report that Bluetooth pairing code given by the Hands Free Link system does not work for certain smartphone models, namely, Samsung Galaxy and Sony Xperia. For these smartphone models, the pairing code for Bluetooth connection must be set to a fixed code of ?0000.? This TSB instructs dealers how to register these smartphones using the pairing code ?0000.?

RECOGNITION TO COMPLETE BEFORE CONNECTION TO THE PHONE BEGINS, TO RECTIFY THE CONDITION WHERE THE HFM ATTEMPTS A BLUETOOTH CONNECTION WITH A MOBILE PHONE WHILE VOICE RECOGNITION IS BOOTING AT THE SAME TIME. IF THE BLUETOOTH CONNECTION COMPLETES BEFORE VOICE RECOGNITION COMPLETES, VOICE RECOGNITION CANNOT BE USED.

Automatic Transmission portion of the affected Service Manual.

This bulletin updates the Automatic Transaxle section of the affected Service Manuals to update procedures for CVT F1CJB, including diagnosis, maintenance, and transaxle disassembly and reassembly.

Variable Transmission.

updated software to minimize shift shock.

Manuals.

Control System Diagnosis of wheel speed sensor codes.

IPHONE/IPOD/IPAD WHEN THE DEVICE IS CONNECTED TO WI‐FI. THIS UPDATE ADDRESSES UNSTABLE, REPEATEDLY CONNECTING AND DISCONNECTING FROM THE VEHICLE'S BLUETOOTH WHEN THE IPHONE'S WI‐FI IS ENABLED. THE CONDITION DOES NOT OCCUR WHEN WI‐FI IS TURNED OFF.

This bulletin supersedes TSB-18-00-003, issued April, 2018, to add updated information for Carrying Capacity Reduced Label.

Service Manuals will be available.

(Service Manual Revision)

Mirage, to contact TechLine for assistance. DO NOT use the metal type TPMS transmitter (p/n 4250B975) as a replacement. Metal TPMS transmitters will not properly fit the wheels of the Mirage.

vibration between the exhaust hanger and body side bracket and intructs dealers to replace the two identified hanger rubber parts with new parts.

Due to the increased occurrence of Mirage/Mirage G4 vehicles exhibiting faulty air conditioning systems caused by low/high refrigerant levels; MMNA would like to remind all Dealer Service Personnel of the correct procedures when submitting warranty claims of this distinction.

of concerns of TPMS light illumination. TPMS DTCs C1911, C1921, C1931, and/or C1941 were usually reported. Many dealers have been replacing the affected TPMS transmitters. Investigation results of the replaced transmitters are "NTF"(no trouble found). The notice references the Service Manual diagnostic procedure for the TPMS transmitter. The Service Manual states, "the TPMS transmitter which cannot be checked may be faulty or the ID code may not be registered, thus do not replace it, but register the ID code. If the transmitter is faulty, it is replaced in the ID code registration process."