2020 MINI Cooper TSBs

start, lock/unlock/climate conditioning) will not be able to reactivate the TCB2. Due to this issue, Remote Services will not function in the vehicle when parked and locked.

worn.

The following fault code is saved in the IHKA (integrated automatic heating/air conditioning system) control unit: 801189 - Engine mixed air right: Initialization fault.

Warranty Extension For the eligible vehicles, MINI USA, a division of BMW of North America, LLC ("MINI USA") is extending the limited warranty for the engine radiator's Environmental Air Catalyst (EAC) sensor (shown) to: 15 years/150,000 miles as determined by the vehicle's original in-service date.

noise can be heard from inside the fuel tank when the tank is full. The customer may describe this noise as a "helicopter noise" from the rear of the vehicle.

Warranty Extension For the eligible vehicles, MINI USA, a division of BMW of North America, LLC ("MINI USA") is extending the limited warranty for the engine radiator's Environmental Air Catalyst (EAC) sensor (shown) to: 15 years/150,000 miles as determined by the vehicle's original in-service date.

more of the following faults are stored in the DME. All models: FC 191C02 - Fuel tank ventilation system 2nd discharge point: malfunction FC 195014 - Differential pressure sensor tank vent valve signal: fixed FC 118001 - Mixture control: mixture too lean FC 118401 - Mixture control: mixture too lean large deviation CAUSE Internal mechanical defect in the tank ventilation valve. The defect can also result in a very loud clicking noise when the valve is cycling.

Bulletin (Revision 2) replaces SI M62 01 19 dated January 2019.The central instrument's outer perimeter LED ring (arrows) does not illuminate when switching on the ignition or with the engine start-stop button. It only illuminates after direct actuation of a component (e.g. setting the temperature radio volume etc.). F57 shown; other models similar Software error in the Automotive Pixel Link driver (APIX driver). APIX is the serial high-speed Gigabit multichannel link that connects displays such as the LED ring with vehicle control modules.

display for brake suspension and air bag system malfunction. The customer may also complain about any of the following: Engine can no longer be switched off Drive position (D) cannot be engaged on the gear selector switch (GWS) Reduction of steering assist After an engine emergency shut-off (either a prolonged long press; or 3 consecutive short presses of the Start/Stop button) and the vehicle going to sleep (identifiable by the lighting of the "Start/Stop button") everything resumes normal functionality and the CCM messages no longer appear. When performing a vehicle test the following diagnostic fault codes are stored in the BDC: CD0420 - "error of Flexray controller on Flexray bus" D91FF9 - "Flexray message data drivetrain 2 (DT_PT_2): Timeout" This message may be read out in the ZGM control unit or Body Domain Controller CAUSE Software in the Body Domain Control unit (BDC).

During load reversal or taking off from a stop there is a creaking or droning noise heard from the lower engine area. CAUSE The bushing in the lower engine stabilizer link is working its way out of its aluminum housing thereby rubbing against the engine oil pan. The bushing in the lower engine stabilizer link (1) is working its way out of its aluminum housing. The aluminum housing starts to rub against the engine oil pan (2).

may become overheated when using low quality fuel. If overheated the valve seat insert may become distorted and wear at an increased rate. Unfavorable software calibration for low quality fuel engine operation.

After engine start the malfunction indicator lamp (MIL) and Check Control message (ID 29) "Engine fault! Power loss" are displayed in the instrument cluster.

vehicles that were produced between February 4 2020 and February 13 2020. Due to a possible production issue the cylinder head will need to be replaced on the affected vehicles.

After a vehicle has been programmed to an I-level greater than 19-11-5xx and lower than I-level 20-03-530; the safety belt (aka seat belt) acoustic warning sounds when in Park (engine running) and the safety belt is unbuckled. The chime/gong lasts for up to 1 minute 40 seconds. The customer only expects the acoustic warning when the vehicle is moving and the safety belt is not buckled. The acoustic warning can occur when the seat is occupied and the safety belt buckle is opened on the driver's or passenger's side. Software in the ACSM4 Control Unit.

replaces SI M32 01 14 dated October 2016. The power assisted steering is unavailable at start up/drive readiness. No communication with the Electric Power Steering (EPS).

indicator lamp (MIL) and/or a different issue the following fault may also be stored in the Digital Motor Electronics (DME). Fault code Control module Fault code text 213A2B DME Increment wheel adaption faulty This situation is not associated with any drivability complaints and only affects vehicles built with a Factory I-level of 19-07-500 and later. An unfavorable DME diagnostic calibration may cause the fault code to be stored. In most circumstances this will cause the MIL to be illuminated.

The Service Engine Soon (MIL) light is on together with the following fault stored in the Digital Motor Electronics (DME). Fault Code: Control Unit: Fault Code Text: 118002 DME Mixture control: Fuel-air mixture too rich In the situation being described the fault is only stored during the cold winter months. Note: Various other causes for a rich mixture fault are possible and should not be overlooked. DME software diagnostic is too sensitive This situation is most likely to occur if the driving profile is one of frequent cold engine starts and/or primarily short distance trips (idle / low load operation) where full engine operating temperature is not reached Due to the lower engine oil temperatures crankcase vapors that contain a higher fuel content are not completely drawn off via the crankcase ventilation system A false DME adaptation routine could then lead to this fault being set.

droning noise heard from the lower engine area. CAUSE The bushing in the lower engine stabilizer link is working its way out of its aluminum housing thereby rubbing against the engine oil pan.

inner door panel of the front right door in the area of the window frame.

completely sealed, causing a water leak.

production.

production.

Dynamic Stability Control (DSC) unit via the On Board Diagnostic (OBD) socket. The DSC data is not processed correctly in the BDC and therefore cannot transmit any diagnostic requests via the OBD using aftermarket scan tools.

lower A-Pillars near the bottom corners of the windshield. Interference between 2 sheet metal panels.

Dynamic Stability Control (DSC) unit via the On Board Diagnostic (OBD) socket. The DSC data is not processed correctly in the BDC and therefore cannot transmit any diagnostic requests via the OBD using aftermarket scan tools.

In some cases after opening they may not correctly latch. A missing seal on the inner Bowden release cable may allow water to enter the cable sheathing and freeze.

As a result, the demand on the batteries has increased. Breakdowns due to an empty battery or problems in the vehicles electrical system can have various causes, most of which are not due to the battery itself. For this reason, a battery replacement will permanently eliminate the problem only in the rarest of cases. The energy diagnosis test module helps to localize these causes. This document covers important information for the dealer on how to handle discharged battery complaints. Without performing the energy diagnosis test plan, the root cause of a discharged battery cannot be identified. In order to properly repair the vehicle the first time, it is very important that the diagnostic test plan is performed to completion; with all results taken into consideration.

As a result, the 12 V positive battery cable may rub against the battery box cover.

securely closed and locked.

unexpectedly not provide power to the vehicle.

unexpectedly not provide power to the vehicle. The high-voltage battery cells may not have been produced according to specifications.

unexpectedly not provide power to the vehicle. The high-voltage battery cells may not have been produced according to specifications.

There may be a potential issue in the welding process of the HV-modules.

This causes the scan tool to read out only the fault memory that was stored first so that any further faults are not displayed.

installation.

(predominantly left turns)

inoperative.

Acoustic abnormality in the area of the recirculated air flap (recirculation flap closing and opening several times). The above may occur individually or in combination.

The locking operation of the door is not affected by the incorrect display.

This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and came in vehicles with option code 609. This uses map North America EVO. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and came in vehicles with option 6UM. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and came in vehicles with option code 609 or 6NP . This uses map North America WAY.

illuminated screen which does not go away after a key cycle or sleep mode. Dead pixels in the Liquid Crystal Display (LCD) diodes. Each individual light pixel on an LCD screen is made up of three diodes- red, blue and green. If all three fail, the pixel will appear as a permanent black dot. Dead pixels can occur as a result of: Blunt force contact to the screen that does not result in a cracked surface Non-functioning diodes Manufacturer defects (e.g., gas bubble).

vehicle is being charged, with the air conditioning running at the same time.

deactivated while the vehicle is in park or neutral. Prior to turning off the A/C, the system was functional and cooling properly. A/C compressor, or The power supply to the A/C compressor is too low.

deactivated while the vehicle is in park or neutral. Prior to turning off the A/C, the system was functional and cooling properly. A/C compressor, or The power supply to the A/C compressor is too low.

The condensate drain hose is blocked by the heat shield - The condensate drain hose is not attached properly to the housing - The condensate drain hose was damaged during installation or previous repair.

boots.

This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via Voice over LTE (VoLTE) function. For this purpose, the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, MINI Assistance and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.

The Connected Drive voice services (Concierge Call, MINI Assistance and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.

The cap was not installed correctly during assembly.

The cap was not installed correctly during assembly.

12,500 may experience premature wear of the left rear brakes. In some cases, there also may be visible damage due to thermal overload.

operating up to customer expectations. Customers can report system errors such as: Vehicle equipped with camera-based ACC, brakes without apparent reason and then does not accelerate When ACC is active, the vehicle does not brake, although it is obvious it should brake; or it even accelerates KAFAS system deactivates independently, due to system limitations that are not clear to the customer KAFAS system cannot be activated due to system limitations that are not clear to the customer When accelerating from a standstill, the vehicle does not automatically start in "Follow mode" Road signs are sporadically not detected Lane departure warning sporadically fails to function For the situations described in this service information bulletin that pertain to normal system limitations, ISTA diagnosis does not show any relevant fault codes stored.

When attempting to stow the convertible top it does not compress into a fully locked position on the left side. This prevents the soft-top bow cover from moving forward into proper operating position as shown in video 54 01 17. Additionally a warning gong sounds and a Check Control Message "Roof not locked" appears. One or both can apply: An issue with the convertible top assembly gripper hook Improper adjustment of the convertible top storage spacer adjustment bolt Damaged folding top felt pad.

evaporator drips, below the instrument panel, into the passenger's footwell. During assembly, the cover of the fresh air intake was not fully seated when the screws were tightened. This cover can then leak condensation out through the existing gap.

evaporator drips, below the instrument panel, into the passenger's footwell. During assembly, the cover of the fresh air intake was not fully seated when the screws were tightened. This cover can then leak condensation out through the existing gap.

The new wheel electronics are identified as Huf Generation 5. These new wheel electronics will need to be programmed using the new tool when replaced or when depressurized (0 psi) for more than 2 minutes.

the front driver's or passenger's seat during forward/back seat adjustment.

e.g., parking lot maneuvers) or accelerating with a medium to large steering angle: Humming or creaking noises from the rear area; slight vibrations, also noticeable from the driver's seat; the vehicle may also jerk slightly.

activated.