2014 MINI Clubman TSBs

The Service Engine Soon lamp is illuminated after reprogramming the vehicle to integration level R056-11-11503 (ISTA/P P45.1.3.0) or higher. When diagnosed, the following fault code is stored in DME fault memory: ??37DE Engine ventilation, heating, triggering: open circuit CAUSE Due to a DME software change, the diagnostic monitoring capability is improved for the engine ventilation heating system. However, a fault will be stored in the fault memory because the engine ventilation heater circuit has a malfunction currently present.

INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, ""Removing and installing or replacing high-pressure pump (N14, N18)"" has a procedure error. The current version of the Repair Instruction states to replace the highpressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15601.2.M130113... 8/30/2013 Page 2 of 2 All vehicles equipped with the N18 engine and produced from 3/2012 and later. When the engine is fitted with a Bosch High-pressure Pump (1) the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightning torques are correct. Refer to EPC for the applicable part numbers when making repairs. "

The customer states that the Service Engine Soon lamp is illuminated and the following fault is stored in the DME: FC 2BF2 Rail pressure sensor, workspace: pressure too high CAUSE A DME calibration error in the fuel pressure diagnostics results in an increased sensitivity.

NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. SUBJECT Service Action: Retrofit of Engine Coolant Temperature Sensor. Internal corrosion can form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading can lead to difficulty in the engine starting and/or a ""Service Engine Soon"" lamp being illuminated."

CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

Vehicles produced from 3/2013 are no longer equipped with an engine coolant thermostat that incorporates the engine coolant temperature sensor (thermostat P/N 11 53 7 647 751). The engine coolant temperature sensor is now an individual component. To accommodate this component change, there was also a production change to the engine wiring harness; this also includes the replacement engine harnesses for earlier produced vehicles. The replacement harness is no longer equipped with the four pin connector for the thermostat / engine coolant temperature sensor, but two separate twopin connectors, one for the coolant thermostat and one for the engine coolant temperature sensor. *The N16 engine switched production to the 11 53 7 534 521 thermostat in 3/2012. This thermostat, like the new 751, incorporates a separate engine coolant temperature sensor. The connectors on the 521 thermostat will not match up to the connectors on a new, replacement engine harness. The 521 thermostat will need to be replaced with the 751 thermostat during this repair.

After reprogramming the vehicle to integration level R056-11-11-503 (ISTA/P P45.1.3.0) or higher, one of the following fault codes are stored in the DME fault memory: Vehicles with N16 engine: * 2F42 Engine ventilation heating, Control The Service Engine Soon lamp is not illuminated. Vehicles with N18 engine: * 37DE Engine ventilation, heating, triggering: open circuit The Service Engine Soon lamp is illuminated. CAUSE Due to a DME software change, the diagnostic monitoring capability is improved for the engine ventilation heating system. However, a fault will be stored in the fault memory because the engine ventilation heater circuit has a malfunction currently present.

Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.

CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

Based on Motorer feedback, MINI has determined that during the first three years of service, some vehicles may require specific additional service work to be performed. MINI USA, a division of BMW of North America, LLC ("MINI USA") is pleased to announce the following Motorer-Focused Satisfaction (MFS) Program. This new program's procedure will be available for your dealer to address these Motorers' concerns, starting with claim repairs dates on or after September 1, 2014. As part of our Motorer Pledge to deliver an incredible MINI motoring experience, for the above-referenced MINI vehicles, we developed this program to increase our Motorers' satisfaction by helping to prevent unexpected dealer service repair visits.

Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a "Service Engine Soon" lamp being illuminated.

Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a "Service Engine Soon" lamp being illuminated.

Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a "Service Engine Soon" lamp being illuminated.

CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

designates changes to this revision SUBJECT N16 and N18 Engine: Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC

increased to 15 years / 186,000 miles as determined from the original first in-service / delivery date.

the MINI Footwell Module (FRM) may become unresponsive. As a result, one or more of the following vehicle electric system-related issues may occur: Headlights including the high beams, and/or taillights are not turning on or off Interior lights are not turning on Turn indicators are not working Instrument cluster indicator lights stay on The IHKA climate control system is not working Power windows are not working Folding mirrors are not working, and/or a Functional remote-control key FOB will not unlock and lock the doors

increased to 15 years / 186,000 miles as determined from the original first in-service / delivery date.

increased to 15 years / 240,000 miles as determined from the original first in-service / delivery date.

As a result, the demand on the batteries has increased. Breakdowns due to an empty battery or problems in the vehicles electrical system can have various causes, most of which are not due to the battery itself. For this reason, a battery replacement will permanently eliminate the problem only in the rarest of cases. The energy diagnosis test module helps to localize these causes. This document covers important information for the dealer on how to handle discharged battery complaints. Without performing the energy diagnosis test plan, the root cause of a discharged battery cannot be identified. In order to properly repair the vehicle the first time, it is very important that the diagnostic test plan is performed to completion; with all results taken into consideration.

During vehicle programming, the CAS (Car Access System) module fails to program with CoAPI error 2082 displayed. Refer to the attachment, which lists the affected CAS serial numbers. The following part numbers are affected: 61 35 9 287 534 61 35 9 226 238 61 35 9 227 053 61 35 9 287 535

When performing an Energy Diagnosis test plan, the battery charge condition information is not available. CAUSE The power management system was not reset properly at the end of vehicle production, leaving the IBS in a failsafe mode.

INFORMATION Parts replacement will not solve the problem if one or more of the conditions described in the situation above caused the alarm to trigger. The sensitivity of the interior ultrasonic sensor cannot be reduced. If the customer wishes to park the vehicle with the sunroof tilted, the window partially open, and/or in an area with excessive local noise, the interior sensor must be switched off by using the following procedure: Press the lock button on the remote control twice in succession. The LEDs flash in short succession for approx. 2 seconds. The interior ultrasonic sensor is switched off until the vehicle is unlocked and locked the next time. NOTE: This information can be found in the Owner's Manual in the ""Controls"" section under ""Switching off the tilt alarm sensor and interior movement detector."""

MINI electrical systems and advancements in vehicle technology have resulted in an increased demand on the vehicle battery. This SI will help the dealer handle ""discharged battery"" complaints. A discharged battery can have various causes, most unrelated to the battery. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to http://www.batteryuniversity.com/parttwo-42B.htm. For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. To repair the vehicle properly the first time in the workshop, the diagnostic test plans must be performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair. CAUSE Discharged battery."

INFORMATION Do not replace parts and do not perform a repair attempt! Explain to the customer that this only happens at high ambient temperatures, which keep the fan running after the ignition is turned off. This Service Information will be updated as soon as a solution is available. A software solution is expected to be available with ISTA/P 2.49.0 in March 2013. New integration level: R056-13-03-501 or higher.

Extension For the above-referenced vehicles, MINI USA, a division of BMW of North America, LLC (MINI USA) is extending the limited warranty for the front passenger's OC3 seat occupancy mat (shown) to: 10 years/120,000 miles as determined by the vehicle's original in-service date.

supersedes SI M01 02 18 dated May 2018.

supersedes SI M01 02 18 dated May 2018.

This Service Information bulletin supersedes SI 01 11 16 dated December 2016.

3rd Party App Metadata ? the album art and song title do not update when streaming audio from Pandora or Spotify, etc

There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware

SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: z Apple iPhones z Samsung S6 and the S6 Edge. Connectivity failure examples are: z Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. z Contact List incomplete z General connection failures z Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) z Samsung S6 and S6 Edge device firmware

The customer is not connected to MINI Customer Relations after dialing the number displayed in the vehicle Kombi or radio. CAUSE During the Pre-Delivery Inspection (PDI), the incorrect telephone number is being written into the vehicle. INFORMATION 1. When performing the PDI test plan, it is extremely important that you select MINI if the ISID is configured for both BMW and MINI. 2. After completion of the PDI test plan, verify that the customer relations number stored in the vehicle is correct. 3. The correct customer relations phone number is 1(866) 275-6464. 4. If the number stored in the vehicle is incorrect and the correct test plan was used, contact your 3g Administrator and have him or her verify the number stored in the ISID. 5.This picture shows the correct number stored in the Combox control unit. Note: To read out telephone number:

Rear camber cannot be adjusted properly. CAUSE Repair instructions not followed properly

A noise may be heard from the front driver's seat back when the customer applies sideways pressure during cornering. CAUSE Surface corrosion on the metal seat back frame can make a squeaking noise when rubbing against the foam rubber padding of the seat back.

designates changes to this revision SUBJECT Erroneous ""Service due"" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness."

The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness.

Mechanism (Gearshift lug assembly portion) has been extended to: 10 years/120,000 miles as determined by the vehicles original in-service date, When a gearshift lug repair kit (item # 2) installation procedure is required to be performed to address a displayed Check Control message (CCM) that states: "P not engaged - secure vehicle with parking brake against rolling away."

The customer may complain of a ""stiff diagonal shift"" (e.g., N-R, R-N, 2-3/3-2 or 4-5/5-4). Also, in some cases, gears cannot be selected, or the selector gear does not go into the neutral position. CAUSE 1. The deflection lever circlip of the gearshift mechanism is damaged or missing. 2. Possible corrosion at the gearshift mechanism (shift cables or transmission gearshift unit)"

The new wheel electronics are identified as Huf Generation 5. These new wheel electronics will need to be programmed using the new tool when replaced or when depressurized (0 psi) for more than 2 minutes.

When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes. Shut-off period varies based on detected situation. This is normal operational behavior.