2005 Mercedes Benz Ml320 TSBs

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

Cause Silicate granulate may have escaped from a damaged bag in the expansion reservoir (not visible), reducing the coolant flow in the heater heat exchanger (see picture). Remedy With the aforementioned complaint, make sure that the cooling circuit is inspected for silicate residues after all standard tests are completed. The silicate residues tend to accumulate upstream of the shutoff valve for the heater hot water pulsed valve. If there are silicate residues in the coolant, the engine must be flushed thoroughly. To make sure that all silicate residues are removed from the cooling circuit, the following parts must also be replaced (cleaning of these components is not sufficient): Coolant expansion reservoir, radiator, oil/water heat exchanger (oil cooler), heater valve, heat exchanger of heater, coolant and, if installed, the electric water pump for the residual heat utilization system. Determine the parts for the respective vehicle in the EPC.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).

The fault code 162500 (water level message - Bosch) or P226997 (water level message - Delphi) or 171600 (filter load - Bosch) is stored in the engine control unit.

Fault code 20BE1B and/or 20BD1B (The heating element of the AdBlue tank has a malfunction) is logged in the Blue-Tec control unit.

Fault code 20BE1B and/or 20BD1B (The heating element of the AdBlue tank has a malfunction) is logged in the Blue-Tec control unit.

the ethanol sensor"

STORED IN THE ENGINE CONTROL UNIT. MODELS 171, 203, 209, 211, 219, 221, 216, 230, 164, 251, AND 403. NO MODEL YEARS LISTED. *PE

INSUFFICIENT VALVE CURRENT IN MODELS SERIES 211, 219; FC5260 DRAIN VALVE OPEN CIRCUIT OR INSUFFICIENT VALVE CURRENT IN MODEL 221; FC5250 DRAIN OPEN CIRCUIT OR INSUFFICIENT VALVE CURRENT IN MODEL SERIES 251, 164. DEFECTIVE CONNECTING CABLES TO DRAIN VALVE AT AIRMATIC COMPRESSOR. THIS RESULTS IN THE SETTING OF THE FAULT CODES. NO MODEL YEARS LISTED. *PE

SOFTWARE CALIBRATION NUMBER (SCN) CODING; ENGINE CONTROL MODULE. THE VEHICLES FUEL TANK LEAK DIAGNOSIS SYSTEM MAY HAVE BEEN INADVERTENTLY DEACTIVATED DURING A VISIT TO THE WORKSHOP. THIS MAY CAUSE THE AFFECTED VEHICLES TO FAIL TO MEET THE STATUTORY REQUIREMENTS FOR INSPECTION AND OR MAINTENANCE (EMISSIONS INSPECTION). *PE

CHANGES TO LIP HOME MODE, POOR OUTPUT, POOR FUEL ECONOMY, COMBUSTION NOISE, VEHICLE STALLS). MAY BE CAUSED BY MALFUNCTION AT PRESSURE REGULATOR VALVE (PRV) DUE TO IMPROPER INSTALLATION. *PE

CAUSED BY AN INSUFFICIENT SEALING OF AIR/WATER BOX WHEN WATER IS USED WHEN ENGINE COMPARTMENT IS CLEANED NEAR RIGHT SIDE OF FIREWALL.

FUEL LOSS AT THE PRESSURE REGULATOR VALVE AND/OR POOR ENGINE RUNNING CHARACTERISTICS (SHAKES, KNOCKS, SURGES, CHANGES TO LIMP HOME MODE, POOR OUTPUT, POOR FUEL ECONOMY, COMBUSTION NOISE). *PE

MODEL YEARS UNKNOWN. *PE

MERCEDES-BENZ MODEL C230, C280, C350, SLK280, SLK350, CLK350, CLK550, E350, E550, CLS550, S600, AND SL550. EQUIPPED WITH M272 ENGINE OR M273 ENGINE. *NJ UPDATED 8/28/08. *PE

Transportability of High-Voltage Batteries Form? accompanied by: , the removed part, the quick test printout, the BMS control unit log printout, the repair documentation and with all required documentation listed in Section E of the Form.

*RM

A WARNING MESSAGE ABOUT LOCKING THE 3RD SEAT ROW MAY ALSO APPEAR IN THE DISPLAY. *PE

FAULT MESSAGE IS DISPLAYED IF THE CHARGE LEVEL IS TOO LOW OR THE PARK PAWL ADDITIONAL BATTERY IS DEFECTIVE. IN ADDITION FAULT CODE FC 9061 AND/OR FC 9062 IS STORED IN THE FRONT SAM. *PE

WHEN INSTALLING THE LEFT OR RIGHT FUEL LEVEL SENSOR, IT IS ESSENTIAL FOR IT TO HAVE UNRESTRICTED, UNOBSTRUCTED MOVEMENT. *PE

MODELS ML63, ML320, ML350, ML500, ML550, GL320, GL450, GL550, R63, R320, R350, R500. MODEL YEAR ALL. *NJ

*RM

MODELS 164.122/8SS (ML 320 AND GL320); 211.022 (E320); 251.122 (4320). YEARS UNKNOWN. *PE

*PE

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

The clunk is heard once when changing from forward to reverse (and vice versa). Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

THE TRANSMISSION PILOT BUSHING MAY HAVE BEEN INSTALLED ON THE CONTROL UNITS WITH NON-TEMPERED SEALING RINGS WHICH MAY CAUSE A SMALL LEAK TO OCCUR. *TT UPDATED 04-11-07. *KB

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

informing them that they need to have an i-button call performed to ensure their mbrace device has registered with the Verizon Telematics systems. If the i-button call failed or if the customer was unable to perform the i-button call, the mbrace agent instructed the customer to make an appointment with their dealer to have the issue corrected and/or i-button call performed. The vehicles impacted range from model year 2002 to 2014.

REFERENCES REVISED AND REFERENCE TO AF DELETED/SUPERSEDES DTB TB 42.45/42. ESP LAMP ON. CONTACT FAULT AT CONNECTION FOR ESP CONTROL UNIT MK25 (N47). NO MODEL YEARS LISTED. *PE

(VEHICLES WITHOUT LED TAIL LAMPS) *PE UPDATED 5/13/09. *PE UPDATED 4/20/11. REPAIR DOES NOT APPLY TO LED TAIL LAMPS. *PE

Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Suitable interior protection ensures that the interior monitoring function continues to operate correctly.

*NJ

ROAD AND WHEN ACCELERATING OR BRAKING, THERE WOULD BE CRACKING NOISES. MODELS 164, 251. NO MODEL YEARS LISTED. *PE

THE SPACER BETWEEN THE BRAKE LINE AND FUEL LINE MAY NOT HAVE BEEN INSTALLED. CHECK FOR PRESENCE OF A SPACER, AND IF MISSING, INSTALL THE SPACER. CHECK THE BRAKE LINE FOR CHAFE MARKS FROM THE FUEL LINE AND REPLACE THE BRAKE LINE IF NECESSARY. MODEL 163. *PE

WHEN TURNING STEERING WHEEL OR MOVING OFF OR BRAKING. THIS MAY BE EMANATING FROM THE BEARING AND HOUSING OF UPPER STEERING SHAFT (FIREWALL PIVOT POINT) OR STEERING COUPLING (LOWER STEERING SHAFT). MODELS 164 AND 251. MODEL YEARS UNKNOWN. *PE

NO MODEL YEARS GIVEN. ALSO INCLUDED MODELS 168 AND 172. *JS

ADHESION BETWEEN CHROME PLATING AND BASE MATERIAL. MODELS 164 AND 251. MODEL YEARS UNKNOWN. *PE

MODELS 203, 209, 210, 211, 215, 220, 230. MERCEDES BENZ. *KB UPDATED 5/13/09. *PE

DUE TO A BENT PIN IN THE DYNAMIC BALANCER, THE SUPPORT SPRING OF THE BEARING BRACKET CAN SLIDE OUT OF PLACE OR BECOME UNHOOKED. MODELS 164, 251, 166, 204, 212. NO MODEL YEARS LISTED. *PE UPDATED 2/1/12. *PE UPDATED 10/3/12. *PE UPDATED 10/21/13. *PE

INOPERATIVE/ (VISIT WORKSHOP) DISPLAYED IN INSTRUMENT CLUSTER. MODEL YEAR UNKNOWN. *NJ UPDATED 3/11/08. *NJ

periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!

MODELS 164, 211, 219, 221 AND 251. INCLUDED 4MATIC, AMG (COMPRESSOR) AMG, BLUETEC AND WAGON. MODEL YEARS UNKNOWN. *PE UPDATED 9/18/09. *PE

SYSTEM (INDIRECT ESP BASED) WITH RUN FLAT TIRES -- MODEL YEAR 2005 TO 2007 (TIRE PRESSURE MONITORING INACTIVE) DISPLAYED IN INSTRUMENT CLUSTER. *NJ