2026 Mercedes-Benz GLE 450 4Matic TSBs

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10P067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. Please update the Head unit software to E505.9

with one of the following scenarios: Flashing without a speed limit (" "). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. NOTE: Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Update head unit software to latest version and the recheck function in the same location. NOTE: Updated head unit software for AMG's has NOT been released yet. ETA 12/2026. If vehicle is still exhibiting one of the symptoms as described exactly as in the complaint section or as shown in the video attachments, open a TIPS case to the Body/Chassis/Entertainment inbox with the following: Video of the concern. Exact location (latitude and longitude is best)

with one of the following scenarios: Flashing without a speed limit (" "). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. NOTE: Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Update head unit software to latest version and the recheck function in the same location. If vehicle is still exhibiting one of the symptoms as described exactly as in the complaint section or as shown in the video attachments, open a TIPS case to the Body/Chassis/Entertainment inbox with the following: Video of the concern. Exact location (latitude and longitude is best)

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. NOTE: Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: The vehicle must be exhibiting the concern as shown in the attachment videos. The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. If the geographic location is known, it is very important that it is provided. Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q3 2026.

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.

2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. The following applies to model series 167 from AEJ 22/1 onward, 192 AMG, 206, 214, 223, 232 AMG, 236, 254, 290 AMG from AEJ 23 onward, 294, 295, 296, 297 and 465: Reinitialize ASSYST Plus under Adaptations Teach-in processes ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.

menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.

2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations Teach-in processes ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.

2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations Teach-in processes ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.

Cause Software A 40/12 - Head-up display and N133/1 - Instrument cluster (IC). Remedy Please do not replace any parts The following steps need to be performed in the order shown below: 1. Xentry > Special functions > 'Entry for retrofits and modifications' add SA code 2O8 (Two 'O' eight) (Please see the attachment) 2. Update the HUD177 software update to the latest available version 3. Update the IC177M software update to the latest available version (software A1779048302 )

Remedy Please do not replace any parts. Step1: Please add SA code 2O8 to the vehicle. Step2: Update the HUD177 to the latest SW Step3: Update the IC177M software update to the latest available version (software A1779048302 ) (E216.0)

Remedy Please do not replace any parts. Step1: Please add SA code 2O8 to the vehicle. Step2: Update the HUD177 to the latest SW Step3: Update the IC177M software update to the latest available version (software A1779048302 ) (E216.0)

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. NOTE: Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q2 2026.

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The robustness measure has been identified and is planned for implementation in the A26/17 E505.9 software. The E505.9 software is expected to be available in XENTRY Q3 2026.

REAR COMFORT PACKAGE (P08), the rear seat heating cannot be activated via voice control. However, the voice control erroneously provides feedback that the seat heating has been activated. Cause A26/17 - MBUX multimedia system (Head unit) software Remedy Software E604 (FUP6) corrects the erroneous feedback from the head unit regarding the activation of the seat heating. Important note: The feature "Activation of seat heating via voice control" is only available in vehicles with codes REAR SEAT ENTERTAINMENT (854/447/864) and 903 REAR COMFORT SEAT HEATING (903) or REAR COMFORT PACKAGE (P08) Availability: Software FUP6 is planned to be released in Q3 2026. Note: Please do not replace any parts for this concern.

The UI continues to show the old stations artwork instead of updating to the new one. Cause Root cause currently being investigated. Remedy Please do not replace any parts. Please create a TIPS case to Body/Chassis/Entertainment inbox.

NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. Cause Calibration of the reversing camera is in progress. This is not a malfunction, but an intended system behavior. Remedy An optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Update both control units and perform on SCN coding: A26/17 (Head Unit) N62/* (PARK Control Unit) IMPORTANT: After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. Prior to releasing the vehicle, please verify the following: Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will reopen, when calibrating, at 9 MPH. The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. This is only for customer satisfaction purposes. Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. Remedy For customer satisfaction purposes, an optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Update both control units and perform on SCN coding: A26/17 (Head Unit) N62/* (PARK Control Unit) IMPORTANT: After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. Prior to releasing the vehicle, please verify the following: Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will reopen, when calibrating, at 9 MPH. The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q4 2025 to early Q1 2026 to rectify concern.

NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. This is only for customer satisfaction purposes. Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. Remedy For customer satisfaction purposes, an optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Update both control units and perform on SCN coding: A26/17 (Head Unit) N62/* (PARK Control Unit) IMPORTANT: After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. Prior to releasing the vehicle, please verify the following: Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will reopen, when calibrating, at 9 MPH. The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. This is only for customer satisfaction purposes. Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. Remedy For customer satisfaction purposes, an optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Update both control units and perform on SCN coding: A26/17 (Head Unit) N62/* (PARK Control Unit) IMPORTANT: After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. Prior to releasing the vehicle, please verify the following: Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will reopen, when calibrating, at 9 MPH. The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

attachment) Head-up display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus (see attachment) Cause Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC) Remedy Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC). Update: A new software version is planned to be released by the end of 2026. Once confirmed the LI will be updated. TIPS cases are no longer needed. Note: Please do not replace any parts for this complaint. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

Cause Under Analysis Remedy 1.Reset the MBUX language (e.g., if the MBUX language is set to English, please change it to any other language and then set it back to English again) 2.If the issue still persists after the step 1, Perform a user data reset of the Head Unit. If the above 2 steps still don't repair the issue, please open a TIPS case. Note: Please do not replace any parts

the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.

NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. This is only for customer satisfaction purposes. Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. Remedy For customer satisfaction purposes, an optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Update both control units and perform on SCN coding: A26/17 (Head Unit) N62/* (PARK Control Unit) IMPORTANT: After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. Prior to releasing the vehicle, please verify the following: Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will reopen, when calibrating, at 9 MPH. The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

shown in red on vehicles with low mileage. Cause Directional control valve may stick. Remedy 1 Read off oil level in instrument cluster and correct if necessary. 2 Perform approx. 1015 engine starts, then clear fault codes. 3 Perform road test with vehicle. If fault code reoccurs during road test: Install new directional control valve.

Fault codes U019F00 or U019F87 current/stored in MRG1 control unit. Cause Various causes Remedy Perform guided test for fault code U019F with XENTRY diagnosis. Verify the following connections are clean and tight. Correct any problems and retest pump actuation: 12V plug at M75/11 48V plug at M75/11 48V connector X192/4 Connections at 48V fuse box F153/2 Sockets 1,2, and 5 at connector 2 of MRG1 control unit M75/11 circuit 41 ground If actuation and above connections are OK, but resistance between M75/11 and engine block is less than 2 ohms or heat shield touching coolant pump, proceed with below steps. 1Modify engine insulation per attached instructions. 2Remove engine control module and measure continuity within control unit between connector 2 pin 1 and connector 6 pin 2. 2aIf open circuit is found, replace engine control unit (MRG1) and perform initial startup. Refer to XENTRY parts information group 54/054 item 300. 3Clear faults and verify M75/11 operating normally.

(figure 1) On the abovementioned vehicles with a mileage up to 15,000 km (about 9,300 mi), noises can occur from the rear axle differential. Cause Drivetrain resonance caused by the gear mesh of the ring and pinion in the rear axle differential in combination with installed damper elements on the axle shafts. Remedy For precise noise analysis and localization, use the chassis ear/NVH kit and the following driving procedure: 1. Drive the vehicle in a tight circle with the steering at full lock in both clockwise and counter clockwise directions. Vary engine load during the maneuvers If a foghornlike noise occurs comparable to the reference video, the vehicle exhibits the condition If the noise is present: 1. Add 15 ml of additive (Friction Modifier) into the rear axle differential via the filler plug IMPORTANT NOTE: Do NOT use Friction Modifier in vehicles equipped with an electronically controlled locking differential (Code 467). 2. Tighten the filler plug 3. Drive the vehicle until the rear axle differential reaches operating temperature Note: Proper activation of the additive requires elevated oil temperatures After the test drive to operating temperature, evaluate the noise when the rear axle is cold and when warm. If the noise is no longer present: The issue is resolved and the vehicle can be released. If there is noticeable improvement: The vehicle can be released with the explanation that the noise will gradually disappear over an extended driving distance. If the noise is still present and remains unchanged: Replace the rear axle differential.

*NOTE Use of tracer DYE for leak checks is not approved. Only approved leak check procedures as per WIS are approved. Cause Possible refrigerant leak. Remedy Perform the following measures : *Important* Photo documentation requirement is no longer in effect as of 10/1/2025. Remedy 1: Replace Evaporator (Only applies to vehicles produced PRIOR to April 15, 2022 and has NOT had the evaporator replaced previously) 1. Ensure that the rest of the AC system has been thoroughly checked for leaks with forming gas as per WIS before condemning the evaporator. 2. If no other leaks are found, replace the evaporator 3. *Important* when you get the new evaporator, check the expansion valve bracket to see if there are any bends (see attachment "Bent Bracket"). a. If bent, remove the expansion valve and bracket and check for damage to the flange (see attachment "Flange Damage"). i. If damage is found, order another evaporator and claim the part under parts warranty. The warranty claim MUST include a photo of the damage found. ii. If no damage is found, flip the bracket and torque to 7Nm. Check the evaporator for proper sealing before fully installing. b. If no bends are found, the evaporator should be installed in the vehicle. Note *If the evaporator housing has been opened or the evaporator or housing has been tampered with, the claim will be debited. Remedy 2: (Applies to all vehicles produced on or AFTER April 15, 2022 up to August 1, 2025) 1. Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . 2. If no leaks were found AND the system came in with no cooling/low charge, OR the evaporator is suspected of leaking: 3. Replace ONLY the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00, in accordance with the procedure outlined in WIS document AR83.30P5520ME. 4. IF THE PRODUCTION DATE IS BETWEEN JUNE 1, 2023 AND JULY 1, 2024, REPLACE THE DRYER AS WELL. (NOT THE CONDENSER) 5. After, charge the system and perform a few drive cycles. 6. Recheck the vehicle for leaks. 7. If no leaks are found, the vehicle can be released. 8. If a minor leak is detected that is less than 50ppm, then perform the following steps: If a leak is detected, fill the system with forming gas Close all doors and windows for 10 minutes. Vehicle off with no blower activation. Open the driver's door and measure ppm detection as soon as the door is open and the sniffer goes into the vehicle. If no leaks are measured, fill the system and release. Remedy 3: (Only applies to vehicles produced AFTER August 1, 2025) Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . If no leaks are found or the expansion valve has been found to be leaking, remove the expansion valve and check the bracket. If the bracket is bent, replace the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00. In the warranty submission, include photos of both sides of the bracket and a side profile so it can be seen that the bracket is bent. If the bracket is NOT bent or leaks from other locations are found, then open a TIPS case with the following: 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 4. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel if the evaporator is suspected. (see attached videos) 5. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 6. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the

Cause Optimized brake pads may produce some noise and is normal at low speeds and light pressure. If the noise begins when the weather is colder, brake noise during this time is normal and the below remedy will not rectify. Remedy NOTE: Exchanging brake discs for noise is not a permanent measure for noise mitigation and cannot be claimed under warranty according to this LI. If the brake pads have not been exchanged prior, vehicle is newer, and this is the first visit for brake noise: Wipe down brake disc and remove any brake dust from holes in brake disc. GLE ONLY Replace brake pads and spring clips. Ensure the double sided adhesive is applied to all locations where the pistons contact the brake pad backing plate. See attachment "Adhesive and Copper Paste Application Area Series 167". Apply Molykote to the sides of the brake pad backing plate in the location shown in the attachment "Adhesive and Copper Paste Application Area Series 167". Clean brake components thoroughly from brake dust, road debris, and other foreign material. After replacing, place the vehicle in sport or sport plus mode and engage brake pedal for 30 seconds. Bed brakes during quality checking according to LI42.10P063502 but only perform once. If the brake pads have been exchanged in a prior visit: The following portion is not warrantable, some brake noise, especially with sport brake packages, is normal. The below is intended to assist in reducing or mitigating brake noise for customer satisfaction purposes. Inspect the condition of the brake system per WIS. Some level of noise is acceptable and cannot be mitigated or removed at all times. Below is a list of items that can cause or exacerbate noises but are normal. With use there will be dirt, debris, brake dust, and other foreign contaminants. If the system is dirty, components should be thoroughly cleaned and wiped down. Inspect the condition of the brake pads and discs. Note any visual anomalies such as glazing, excess rust formation, pad imprints from long stationary times, etc... Driving styles. Does the noise only occur at very low speeds when coming to a stop such as with very light brake pressure? When coming to a stop and applying increased brake pressure, does the noise reduce or disappear? If so, this is normal operation. Brake pressure and application style (stopandgo traffic with consistent low brake pressure riding brakes where the brakes cannot cool sufficiently between applications). Ambient temperatures, especially colder ambient temperatures. Lower ambient temperatures can also introduce additional road debris, such as salt.

Remedy Check the compressor's index and part number Figure 1 against Table 1. If listed please perform the following: 1. Replace the compressor, drier, and expansion valve using the applicable WIS instructions. 2. Flush the system using the applicable WIS instructions.

Cause During diagnostics of a front end noise, workshop is under the impression the noise is coming from the steering gear. Remedy If the root cause of the noise cannot be found and is seemingly from the steering rack, perform the below LI's and diagnostics. If they have been performed and the root cause still cannot be determined, a TIPS case must be opened to the Body/Chassis/Entertainment team prior to replacing the steering rack. LI46.35P067339 "Rattling, Humming, Dry Sliding/Gravel Noise When Steering" LI46.35P071461 "Check Tie Rod Outer Joint of Steering Gear" LI46.10P077391 "Knocking Noise In The Area Of The Steering Gear or Steering Column Tube When Braking Or Moving Off; The Steering Wheel Can Also Be Felt To "Crack"" Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Keep the boot clamps in case the rack is returned. If the noise is described as "clacking" or "knocking" when moving the wheel back and forth in quick oscillations and the thrust element in the steering rack has NOT been checked yet, please perform a check and subsequent adjustment, if necessary, as detailed in AR46.20P0601ME. Remove sway bar links and see if noise persists. Perform NVH timedomain noise diagnosis pointing to the steering rack as the root cause. The TIPS case must contain the following: Video underneath the vehicle with clearly audible noise while engine is running. Video inside the vehicle with clearly audible noise while engine is running. Vehicle checked for history of collisions. Vehicle history checked for other noise complaints in the area. List of other checked components (suspension, drive line components, wheel bearings, etc...). Along with the audible noise, does the feel/noise change through only a certain part of the steering arc sweep? Provide the thrust element before and after readings.

Cause During diagnostics of a front end noise, workshop is under the impression the noise is coming from the steering gear. Remedy Workshop diagnostics point to the steering gear as the root cause of the noise and the below LI's and items have been ruled out. LI46.35-P-067339 - "Rattling or Humming Noise When Steering" LI46.35-P-071461 - "Check Tie Rod Outer Joint of Steering Gear" LI46.10-P-077391 - "Knocking Noise In The Area Of The Steering Gear or Steering Column Tube When Braking Or Moving Off; The Steering Wheel Can Also Be Felt To "Crack"" If the noise is described as "clacking" or "knocking" and the thrust element in the steering rack has NOT been checked yet, please perform a check and subsequent adjustment, if necessary, as detailed in AR46.20-P-0601ME. If the above has been completed and the noise is still present, please continue with the below: Video underneath the vehicle with clearly audible noise. Video inside the vehicle with clearly audible noise. Vehicle checked for history of collisions. List of other checked components (suspension, drive line components, wheel bearings, etc...). Check integrity of dust boots and dust boot clamps. Ensure no water has entered into the steering rack. Along with the audible noise, does the feel/noise change through only a certain part of the steering arc sweep? Provide the thrust element before and after readings. If the above is completed and no findings are noted, please open a TIPS case to the Body/Chassis/Entertainment inbox.

Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

Cause Optimized brake pads may produce some noise. Remedy NOTE: Exchanging brake discs for noise is not a permanent measure for noise mitigation and cannot be claimed under warranty according to this LI. If the brake pads have not been exchanged prior and this is the first visit: Wipe down brake disc and remove any brake dust from holes in brake disc. Replace brake pads and spring clips. Ensure the double sided adhesive is applied to all locations where the pistons contact the brake pad backing plate. See attachment "Adhesive and Copper Paste Application Area - Series 167". Apply Molykote to the sides of the brake pad backing plate in the location shown in the attachment "Adhesive and Copper Paste Application Area - Series 167". Clean brake components thoroughly from brake dust, road debris, and other foreign material. After replacing, place the vehicle in sport or sport plus mode and engage brake pedal for 30 seconds. Bed brakes during quality checking according to LI42.10-P-063502 but only perform once. If the brake pads have been exchanged in a prior visit: The following portion is not warrantable, some brake noise, especially with sport brake packages, is normal. The below is intended to assist in reducing or mitigating brake noise for customer satisfaction purposes. Inspect the condition of the brake system per WIS. Some level of noise is acceptable and cannot be mitigated or removed at all times. Below is a list of items that can cause or exacerbate noises but are normal. With use there will be dirt, debris, brake dust, and other foreign contaminants. If the system is dirty, components should be thoroughly cleaned and wiped down. Inspect the condition of the brake pads and discs. Note any visual anomalies such as glazing, excess rust formation, pad imprints from long stationary times, etc... Driving styles. Does the noise only occur at very low speeds when coming to a stop such as with very light brake pressure? When coming to a stop and applying increased brake pressure, does the noise reduce or disappear? If so, this is normal operation. Brake pressure and application style (stop-and-go traffic with consistent low brake pressure riding brakes where the brakes cannot cool sufficiently between applications). Ambient temperatures, especially colder ambient temperatures. Lower ambient temperatures can also introduce additional road debris, such as salt.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% a negative charge balance A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked). Vehicles with code B01+801: When charging while stationary, the 48V battery must have a state of charge (SOC) of 70% before the 12V primary battery, or the secondary battery in the case of code 503, can be charged. To ensure optimum battery care, please also comply with the existing Service Information documents regarding the handling of stock vehicles (SI54.10-P-0024A) and on remaining in transport mode (SI54.00-P-0004A) until immediately before handover to end customers. Special note: Do not replace any parts, if the message has occurred due to battery discharge as a result of the driving profile or the ignition being switched on (see attached examples); in such cases separate warranty and goodwill invoicing is not possible, as this is a normal on-board electrical system protection function. Likewise battery care and recharging do not qualify as a W&G case. Please advise customers accordingly regarding the above-mentioned issues relating to vehicle use.

Cause Optimized brake pads may produce some noise. Remedy If the brake pads have not been exchanged prior and this is the first visit: Wipe down brake disc and remove any brake dust from holes in brake disc. Replace brake pads and spring clips. Ensure the double sided adhesive is applied to all locations where the pistons contact the brake pad backing plate. See attachment "Adhesive and Copper Paste Application Area - Series 167". Apply Molykote to the sides of the brake pad backing plate in the location shown in the attachment "Adhesive and Copper Paste Application Area - Series 167". Clean brake components thoroughly from brake dust, road debris, and other foreign material. After replacing, place the vehicle in sport or sport plus mode and engage brake pedal for 30 seconds. Bed brakes according to LI42.10-P-063502 but only perform once. If the brake pads have been exchanged in a prior visit: Inspect the condition of the brake system per WIS. Some level of noise is acceptable and cannot be mitigated or removed at all times. Below is a list of items that can cause or exacerbate noises but are normal. With use there will be dirt, debris, brake dust, and other foreign contaminants. If the system is dirty, components should be thoroughly cleaned and wiped down. Inspect the condition of the brake pads and discs. Note any visual anomalies such as glazing, excess rust formation, pad imprints from long stationary times, etc... Driving styles. Does the noise only occur at very low speeds when coming to a stop such as with very light brake pressure? When coming to a stop and applying increased brake pressure, does the noise reduce or disappear? If so, this is normal operation. Brake pressure and application style (stop-and-go traffic with consistent low brake pressure riding brakes where the brakes cannot cool sufficiently between applications). Ambient temperatures, especially colder ambient temperatures. Lower ambient temperatures can also introduce additional road debris, such as salt. NOTE: Exchanging brake discs for noise is not a permanent measure for noise mitigation and is not recommended for noise concerns unless there are other factors involved.

*NOTE - Use of tracer DYE for leak checks is not approved. Only approved leak check procedures as per WIS are approved. Cause Possible refrigerant leak. Remedy Perform the following measures : *Important* - Photo documentation requirement is no longer in effect as of 10/1/2025. Remedy 1: Replace Evaporator (Only applies to vehicles produced PRIOR to April 15, 2022 and has NOT had the evaporator replaced previously) 1. Ensure that the rest of the AC system has been thoroughly checked for leaks with forming gas as per WIS before condemning the evaporator. 2. If no other leaks are found, replace the evaporator Note - *If the evaporator housing has been opened or the evaporator or housing has been tampered with, the claim will be debited. Remedy 2: (Applies to all vehicles produced on or AFTER April 15, 2022 up to August 1, 2025) 1. Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . 2. If no leaks were found AND the system came in with no cooling/low charge, OR the evaporator is suspected of leaking: 3. Replace ONLY the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00, in accordance with the procedure outlined in WIS document AR83.30-P-5520ME. 4. IF THE PRODUCTION DATE IS BETWEEN JUNE 1, 2023 AND JULY 1, 2024, REPLACE THE DRYER AS WELL. (NOT THE CONDENSER) 5. After, charge the system and perform a few drive cycles. 6. Recheck the vehicle for leaks. 7. If no leaks are found, the vehicle can be released. 8. If a minor leak is detected that is less than 50ppm, then perform the following steps: If a leak is detected, fill the system with forming gas Close all doors and windows for 10 minutes. Vehicle off with no blower activation. Open the driver's door and measure ppm detection as soon as the door is open and the sniffer goes into the vehicle. If no leaks are measured, fill the system and release. Remedy 3: (Only applies to vehicles produced AFTER August 1, 2025) Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . If no leaks are found or the expansion valve has been found to be leaking, remove the expansion valve and check the bracket. If the bracket is bent, replace the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00. In the warranty submission, include photos of both sides of the bracket and a side profile so it can be seen that the bracket is bent. If the bracket is NOT bent or leaks from other locations are found, then open a TIPS case with the following: 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 4. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel if the evaporator is suspected. (see attached videos) 5. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 6. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 7. Provide photos of both sides of the bracket and a side profile so it can be seen that the bracket is not bent. 8. Open a TIPS case in the HV/LV inbox labeled "167 AC leak after April 1, 2025" with all attachments. NOTE: (Applies to all 167's) Please see the list of WIS documents for forming gas leak check and recharging of the system. Review PCTT 9/25 for forming gas best practices. Review PCTT 5/25 for bracket removal best practices. See attachment for further instructions.

Please follow the relevant guided tests for the 223 and 206. For 223 with fault code B1FCB97 follow LI54.10-P-076026. Various causes are possible. The faults listed in the various causes do not all have to be present at all times. Some of these complaints may overlap. Rely on the faults listed in the Cause section for identifying the correct Remedy. 1. No start 2. Yellow or red instrument cluster message for 48 V on-board electrical system battery (G1/3) 3. Limp home mode, overheating, A/C not blowing cold, or loss of acceleration 4. Check Engine Light Cause Cause 1: Software causes Intermittent No Starts with fault B183387 in DC/DC converter N83/1 Cause 2: Software causes Permanent No Start with fault B183349. May also have fault B183371. Cause 3: Hardware short circuit in 48V system causes fault B183319 in 48V battery. May also have fault B183371. Cause 4: Internal 48V battery Peltier cooling element failure causes fault B183397 Cause 5: This will Always have fault code B183371 but different from cause 2 and 3 -- it will Not have B183349, B183319, or any other faults in the 48V battery. This will only have fault B183371 in 48V battery. Cause 5 is from the 48V battery detecting an abnormality which then causes the 48V battery to disconnect itself. The disconnected 48V battery then causes subsequent symptoms: Limp Home Mode, overheating, A/C not blowing cold, or loss of acceleration Cause 6: Check Engine Light with fault P0606F1 in the N127 PTCU Cause 7: Check Engine Light with possible no start and fault P057FF1 Remedy Note: each of these remedies correspond to a specific cause. Make sure to match correct Cause with Remedy. Remedy 1: 1. Check the 12V power supply and LIN connection 2. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 3. Road test and release vehicle if no further symptoms Remedy 2: 1. Charge the 12V battery (Charging current <5A) 2. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 3. Road test and release vehicle if no further symptoms If the faults return or cannot be cleared: 1. XENTRY MUST be connected with VCI cable to correctly complete this remedy. 2. Complete guided test for B183349. 3. If guided test completes, vehicle starts, and drive cycles show no further symptoms, release vehicle. 4. If after guided test completes, XENTRY states to replace 48V battery: replace only 48V battery. If vehicle is a MY21 w/M256 engine, update SW in 48V battery 5. If this is a repeat visit for fault B183349 and guided test has already been completed, open a TIPS case. 6. If guided test does not complete OR symptoms are still present open a TIPS case. 7. If communication cannot be established with 48V battery perform physical layer check at 12V wiring to DCDC. If no abnormalities found, replace the 48V battery. 8. If guided test completes but a new fault code is present (such as B183319, B183371, etc.) follow the relevant Cause/Remedy for that fault in this LI. Remedy for 3: (If this occurred after Campaign 2025050001, this Li does not apply and LI54.10-P-079772 should be followed) 1. If fault is not Current (only Stored): 1. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 2. Road test and release vehicle if no further symptoms If the faults return or this is a second visit after the SW update: 1. Complete the guided test for B183319 2. Perform XENTRY actuations for all 48V components. 3. Create a TIPS case with ALL Preliminary measures required as noted below for Remedy 5 4. Upload to TIPS case ISA performance data from the N129. 5. ISA performance data location in XD: 6. N129 control unit under Special Procedures 7. "Procedures for support queries to market support" 8. "Collation of diagnosis performance data" 9. "engine at idle" See attachment for further instructions.

Cause Optimized brake pads may produce some noise. Remedy If the brake pads have not been exchanged prior and this is the first visit: Wipe down brake disc and remove any brake dust from holes in brake disc. Replace brake pads and spring clips. Ensure the double sided adhesive is applied to all locations where the pistons contact the brake pad backing plate. See attachment "Adhesive and Copper Paste Application Area - Series 167". Apply Molykote to the sides of the brake pad backing plate in the location shown in the attachment "Adhesive and Copper Paste Application Area - Series 167". Clean brake components thoroughly from brake dust, road debris, and other foreign material. After replacing, place the vehicle in sport or sport plus mode and engage brake pedal for 30 seconds. Bed brakes according to LI42.10-P-063502 but only perform once. If the brake pads have been exchanged in a prior visit: Inspect the following portions of the brake system. Please note that the list is not exhaustive and WIS should be consulted for additional measures: With use there will be dirt, debris, brake dust, and other foreign contaminants. Noise can be caused and exacerbated due to the aforementioned reasons. If the system is dirty, components should be thoroughly cleaned and wiped down. Inspect the condition of the brake pads and discs. Note any visual anomalies such as glazing, excess rust formation, pad imprints from long stationary times, etc... These items should be addressed as they can cause or contribute to noise. Driving styles. Does the noise only occur at very low speeds when coming to a stop such as with very light brake pressure? When coming to a stop and applying increased brake pressure, does the noise reduce or disappear? If so, this is normal operation. NOTE: Exchanging brake discs for noise is not a permanent measure for noise mitigation unless there are other factors involved, such as glazing of the brake pads.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

Cause During diagnostics of a front end noise, workshop is under the impression the noise is coming from the steering gear. Remedy Workshop diagnostics point to the steering gear as the root cause of the noise and the below LI's have been ruled out. LI46.35-P-067339 - "Rattling or Humming Noise When Steering" LI46.35-P-071461 - "Check Tie Rod Outer Joint of Steering Gear" LI46.10-P-077391 - "Knocking Noise In The Area Of The Steering Gear or Steering Column Tube When Braking Or Moving Off; The Steering Wheel Can Also Be Felt To "Crack"" If the above has been completed and the noise is still present, please continue with the below: Video underneath the vehicle with clearly audible noise. Video inside the vehicle with clearly audible noise. Vehicle checked for history of collisions. List of other checked components (suspension, drive line components, wheel bearings, etc...). Check integrity of dust boots and dust boot clamps. Ensure no water has entered into the steering rack. Along with the audible noise, does the feel/noise change through only a certain part of the steering arc sweep? If noise is described as a "clacking" noise when moving the steering wheel back and forth, please navigate to WIS and find and perform the document "Setting play between thrust element and steering rack". Provide both pre-adjustment and post-adjustment numbers. If the above is completed and no findings are noted, please open a TIPS case to the Body/Chassis/Entertainment inbox.

or without Illumination of Check Engine Light with DTC's C10159A (A108/2, A108/3) and P0AFB00 (N129) Cause PTCU software robustness. Remedy Check N127 - PTCU (Powertrain Control Unit) hardware and software numbers. If software number matches a "Hardware Number" and "Predecessor Software #", update software. If software number is not shown in "Predecessor Software #" and condition exists, open a TIPS case to the High Voltage/ Low Voltage inbox.

*NOTE - Use of tracer DYE for leak checks is not approved. Only approved leak check procedures as per WIS are approved. Cause Possible refrigerant leak. Remedy Perform the following measures : *Important* - Photo documentation requirement is no longer in effect as of 10/1/2025. Remedy 1: Replace Evaporator (Only applies to vehicles produced PRIOR to April 15, 2022 and has NOT had the evaporator replaced previously) 1. Ensure that the rest of the AC system has been thoroughly checked for leaks with forming gas as per WIS before condemning the evaporator. 2. If no other leaks are found, replace the evaporator Note - *If the evaporator housing has been opened or the evaporator or housing has been tampered with, the claim will be debited. Remedy 2: (Applies to all vehicles produced on or AFTER April 15, 2022 up to April 1, 2025) 1. Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . 2. If no leaks were found AND the system came in with no cooling/low charge, OR the evaporator is suspected of leaking: 3. Replace ONLY the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00, in accordance with the procedure outlined in WIS document AR83.30-P-5520ME. 4. IF THE PRODUCTION DATE IS BETWEEN JUNE 1, 2023 AND JULY 1, 2024, REPLACE THE DRYER AS WELL. (NOT THE CONDENSER) 5. After, charge the system and perform a few drive cycles. 6. Recheck the vehicle for leaks. 7. If no leaks are found, the vehicle can be released. 8. If a minor leak is detected that is less than 50ppm, then perform the following steps: If a leak is detected, fill the system with forming gas Close all doors and windows for 10 minutes. Vehicle off with no blower activation. Open the driver's door and measure ppm detection as soon as the door is open and the sniffer goes into the vehicle. If no leaks are measured, fill the system and release. Remedy 3: (Only applies to vehicles produced AFTER April 1, 2025) *TIPS Case Required if leak is found other than a bent bracket* Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . If no leaks are found or the expansion valve has been found to be leaking, remove the expansion valve and check the bracket. If the bracket is bent, replace the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00. In the warranty submission, include photos of both sides of the bracket and a side profile so it can be seen that the bracket is bent. If the bracket is NOT bent or leaks from other locations are found, then open a TIPS case with the following: 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 4. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel if the evaporator is suspected. (see attached videos) 5. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 6. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 7. Provide photos of both sides of the bracket and a side profile so it can be seen that the bracket is not bent. 8. Open a TIPS case in the HV/LV inbox labeled "167 AC leak after April 1, 2025" with all attachments. NOTE: (Applies to all 167's) Please see the list of WIS documents for forming gas leak check and recharging of the system. Review PCTT 9/25 for forming gas best practices. See attachment for complete instructions

the vehicle is stationary and ECO Start/Stop is active (combustion engine is off). The noise is more noticeable outside the vehicle and in acoustically shielded areas such as closed rooms or garages. Cause The noise in the valve body (EHS) is caused by superimposed pressure peaks acting on the valves. This phenomenon occurs only after a certain running-in period due to the influence of micro-contamination in the valve bores. Remedy A hardware modification of the electro-hydraulic control unit (EHS) is currently being implemented (no change to the part number). This will be incorporated into series production and as a spare part starting from 12/2025. This is only a comfort-related complaint and has no impact on the functionality or service life of the transmission. For sensitive customers, the following measures can be performed: 1. Replace the electro-hydraulic control unit (EHS), the oil pan, and the transmission fluid. - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement. (See attached location guide)

control unit software for the front signal acquisition and actuation module (SAM-F) may not correspond to the current series production configuration and it is possible that a communication error may occur. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will perform a software update of the front signal acquisition and actuation module.

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by doubleclicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module NOTE: Occasionally to verify complaint, the steering column/vehicle needs to be in direct sunlight or hot conditions for a few hours. If noise only occurs when adjusting the steering column via electric actuation, please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on all pivot points including, but not limited to, green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, wipe excess grease off and perform greasing and movement to limit stops in all directions again. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. Include detailed items of the following: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

Complaint No. 1: Sporadic "Headlamp Inoperative" message in the instrument cluster (IC), fault code in control unit N10/6 FSAM: U118A02 communication with the left headlamp range adjustment control unit is faulty. General signal fault. or U118A08 Communication with the left headlamp range adjustment control unit is faulty. Faulty signal or faulty message. Complaint No. 2: The instrument cluster (IC) displays the message "Adaptive High Beam Assist inoperative"; fault code present in LED control unit E1n11 or E2n11: B178392 "LED driving light actuation" control unit is faulty. Function or command is faulty. Cause Complaint No. 1: software fault. Complaint No. 2: undervoltage threshold value set inappropriately during vehicle start. Remedy For complaint No. 1 and No. 2: Perform a software update on all headlamp and LED control units: E1n9, E1n11, E2n9 and E2n11 If the fault persists: For complaint No. 1: Replace HLI E1n9 control unit. For complaint No. 2: Replace PXL E1n11 or E2n11 control unit. Note: Headlamps must not be replaced for these complaints.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again and anywhere there are movement or friction points that the noise seems to be emanating from. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

There is an implausible signal." In the quick test, there are also no other DTC's in other control units that point to or reference N80 Steering Column Control Module ("SCCM"). There is no effect on any other components or vehicle functions and it does not cause an instrument cluster light. Cause The DTC only ever occurs during initialization (initialization occurs after bus sleep). The SCCM then resets itself. Remedy 1. If the error is stored and no other control unit points to the N80 SCCM ignore and erase. Software expected in Q4 2026. 2.If the DTC is in the N80 SCCM AND the following DTC's are in N30/3 (Electronic Stability Program) and N68 (Electric Power Steering): N30/3 ESP: U071286, Steering column tube module control unit has a malfunction. There is an incorrect signal. N68 EPS: U042986, Implausible data were received from the steering column module. There is an incorrect signal. Please open a TIPS case to the Body/Chassis/Entertainment inbox.

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 double-click on the locking button As of modification year 22/1, by pressing and holding the locking button + double-clicking on the release tab On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The instrument cluster message and the FC memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 206 and 223 with code 802: Perform SCN coding in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Please do not replace any parts even if the FC P0CFE00 coding continues to appear after successfully completing this step. A new software fix is currently in development and will likely be published in 01/2026. Replacing parts will not remedy the issue. For model series 243: The correction is already available. Perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

The instrument cluster display will remain operational. - No audio is present from the sound system - MBUX multimedia system (A26/17) may not be shown on the initial quick test - Various other MBUX multimedia system (A26/17) related complaints Cause Water ingress through the air vent under the front passenger seat (see attached, note that the vents are facing the rear of the vehicle). As a result, the head unit (A26/17) may become damaged. Inspect the MBUX multimedia system (A16/17) hardware, including all attached wiring and connectors, for traces of water and/or corrosion (see attached picture for example). Remedy Avoid using rubber floor mats for the second row seats on which water can collect and subsequently enter the air vent under the front passenger seat. An optimized cover is now available for the air vent under the front passenger seat (see parts note). To avoid a reoccurrence of water damage, install this cover. Note: Only primary losses resulting from the ingress of fluids that can be attributed to a production error is covered by the warranty. Fluids that are introduced into the vehicle as a result of environmental influences, incorrect repairs or incorrect use by the customer are not covered by the warranty. The damage code specified in this document only applies for the installation of the fan shroud.

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The fault message and the fault memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 167, 214, 254 and 223 with code 802: Perform SCN coding in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Please do not replace any parts even if the FC P0CFE00 coding continues to appear after successfully completing this step. A new software is currently in development and will become available in late 01/2026. Replacing parts will not remedy the issue. For model series 243: The correction is already available. Please inform the workshop to perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2 3 key cycles. The vehicle can be released back to the customer.

Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 23rd, 2026. After July 23rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

Cause Signal timing error. Remedy 167: SW has been released. Update the FSAM to the latest SW version. 465, 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

Cause Signal timing error. Remedy 167: SW has been released. Update the FSAM to the latest SW version. 465, 290: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

movement of the wiper on the driver's side or front passenger side (see Figure 1). Cause During replacement of worn wiper blades, the wrong blades were installed, contrary to the specifications. Left-hand drive vehicle: Incorrect: A1678209201 Correct: A1678208703 The standard wiper system from model series 167 was changed in October 2022. The wiper arms of the standard system after the switchover have a higher clamping force and are not compatible with the wiper blades before the switchover. The wiper lip of a wiper blade before switchover is deformed due to the higher contact pressure of the wiper arm, which can result in a 510 cm wide strip in the area of the wiper blade attachment not being fully wiped. Identification of the wiper blades installed on the vehicle: Wiper blades for vehicles up to October 2022 have a clip between the connector and the end of the blade Wiper blades for vehicles produced from October 2022 onwards do not have a clip between the connector and the tip of the blade See Picture 2 Note: The correct wiper blades were installed on the vehicle at the factory. This does not constitute a defect attributable to the manufacturer. Remedy Install the correct wiper blades intended for the vehicle

The deadline for all dealer returns is no later than Thursday, April 23, 2026. After April 23rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

movement of the wiper on the driver's side or front passenger side (see Figure 1). Cause During replacement of worn wiper blades, the wrong blades were installed, contrary to the specifications. Right-hand drive vehicle: Incorrect: A1678209301 Correct: A1678208803 The standard wiper system from model series 167 was changed in October 2022. The wiper arms of the standard system after the switchover have a higher clamping force and are not compatible with the wiper blades before the switchover. The wiper lip of a wiper blade before switchover is deformed due to the higher contact pressure of the wiper arm, which can result in a 510 cm wide strip in the area of the wiper blade attachment not being fully wiped. Identification of the wiper blades installed on the vehicle: Wiper blades for vehicles up to October 2022 have a clip between the connector and the end of the blade Wiper blades for vehicles produced from October 2022 onwards do not have a clip between the connector and the tip of the blade See Picture 2 Note: The correct wiper blades were installed on the vehicle at the factory. This does not constitute a defect attributable to the manufacturer. Remedy Install the correct wiper blades intended for the vehicle

Cause Signal timing error. Remedy This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer. There is software in development for this concern.

transmission control unit (VGS) in the automatic transmission does not meet current MBAG specifications. The polarities of the magnets in the transmission control unit (VGS) may have been inadvertently swapped. This, in turn, could lead to complaints regarding shift quality and gear lockups. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace fully integrated transmission control unit (Y3/8n4) for the automatic transmission.

OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: Hitting the curb/posts with the front wheels. Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). Cracks (1) High pressure cleaner (2) Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CPR = Car Package Release (For MB.OS) CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465, 906 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not preauthorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Axle Half Shaft noise when changing direction - Front) LI33.30-P-056665 (Axle Half Shaft noise when changing direction - Rear) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Cause Internal tolerances of the electric rollbar. Remedy 1. Confirm front or rear roll bar. 2. Remove the affected sway bar links and carefully drive vehicle. Noise not resolved with sway bar links removed > Not appliable to this LI, noise is from a different component. Noise resolved with sway bar links removed > Current parts may make some noise and is currently state of the art. Optimized, quieter parts will be available Q4 2026, please release vehicle until such time parts are available. For further questions, inquiries, or sound levels approximately equal to or above what is shown in the attachment, open a TIPS case to the Body, Chassis, Entertainment inbox.

squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Cause Delamination of film on carrier plate. Remedy Additional replacement part numbers have been approved for the affected model series V/C/X167, X294 and X296.

(see attachment) Cause The cause is currently being investigated. Remedy Update the HU7 to the latest software version, then perform a factory reset of the HU7. Steps to perform factory reset: Navigate to Settings > System > Reset > Reset to factory settings and confirm If the problem persists, please record HU7 log and also a trace of the Body CAN (For Star 2 Body Can 1 and for Star 3 Body Can 2) during the symptom and send via a TIPS case to the Body/Chassis/Entertainment inbox. Note: Only collect and submit the log and trace if the symptom can be reliably reproduced.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Cause Many possible root causes Remedy *Note - This Li does not apply if there are other Li's that apply to your concern OR you have a fault and/or guided test that leads to a root cause. AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements (Template attached to be used for submission of Warranty claim and/or TIPS case) Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements Cooling Capacity Test (If System Has a Charge) Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs - Warranty Submission Requirements on the Repair Order Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found

Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.