2019 Mercedes-Benz GLC350E TSBs

enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage Detection ("DMTL") on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership. Why the Warranty extension? On certain Model Year 2018 - 2024 A / C / CLA / CLS / E / G / GLA / GLB / GLC / GLE / GLS / GT / S / SL Mercedes-Benz vehicles, under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code ("DTC") entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp ("MIL"). Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be covered under this extended warranty and performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (MIL).

G-Class, GLC, GT, S-Class (205, 463, 253, 190 & 222 platforms) vehicles, the engine control unit software does not correspond to current production specifications. It is therefore possible that on-board diagnostics and/or exhaust gas emissions requirements may not be fulfilled.

our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valve might also increase exhaust gas emission. Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) hereby notifies you of additional benefits regarding your vehicle. Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has extended the warranty for the accelerator pedal wiring harness and connectors from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles for certain Model Year (MY) 2016-2019 Mercedes-Benz E-Class and GLC-Class vehicles (213, 238, and 253 platforms). This warranty extension applies to the electrical wiring and plug connection on the accelerator pedal, as it may not meet current production specifications. When the vehicle is being driven, contact resistance could occur in the accelerator pedal signal lines which would be detected by the engine control unit. As a result, the engine could go in to limp home mode. Also, ESP, BAS, PRE-SAFE, HOLD function, Hill-Start Assist and ESP trailer stabilization may be unavailable, and the Adaptive Brake Assist and/or ATTENTION ASSIST may be temporarily deactivated. These support functions are available again after an ignition off/on cycle. The brake, steering, and ABS systems continue to operate with normal effectiveness. These restrictions are immediately indicated in the instrument cluster with multiple messages.

enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) hereby notifies you of additional benefits regarding your vehicle. Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has extended the warranty for the accelerator pedal wiring harness and connectors from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles for certain Model Year (MY) 2016-2019 Mercedes-Benz E-Class and GLC-Class vehicles (213, 238, and 253 platforms). This warranty extension applies to the electrical wiring and plug connection on the accelerator pedal, as it may not meet current production specifications. When the vehicle is being driven, contact resistance could occur in the accelerator pedal signal lines which would be detected by the engine control unit. As a result, the engine could go in to limp home mode. Also, ESP, BAS, PRE-SAFE, HOLD function, Hill-Start Assist and ESP trailer stabilization may be unavailable, and the Adaptive Brake Assist and/or ATTENTION ASSIST may be temporarily deactivated. These support functions are available again after an ignition off/on cycle. The brake, steering, and ABS systems continue to operate with normal effectiveness. These restrictions are immediately indicated in the instrument cluster with multiple messages.

our customers, Mercedes-Benz USA, LLC (MBUSA) hereby notifies you of additional benefits regarding your vehicle. Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has extended the warranty for the accelerator pedal wiring harness and connectors from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles for certain Model Year (MY) 2016-2019 Mercedes-Benz E-Class and GLC-Class vehicles (213, 238, and 253 platforms). This warranty extension applies to the electrical wiring and plug connection on the accelerator pedal, as it may not meet current production specifications. When the vehicle is being driven, contact resistance could occur in the accelerator pedal signal lines which would be detected by the engine control unit. As a result, the engine could go in to limp home mode. Also, ESP, BAS, PRE-SAFE, HOLD function, Hill-Start Assist and ESP trailer stabilization may be unavailable, and the Adaptive Brake Assist and/or ATTENTION ASSIST may be temporarily deactivated. These support functions are available again after an ignition off/on cycle. The brake, steering, and ABS systems continue to operate with normal effectiveness. These restrictions are immediately indicated in the instrument cluster with multiple messages.

In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the intake line assembly in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended,resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valvemight also increase exhaust gas emission. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has amalfunction.

Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% a negative charge balance A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked). Vehicles with code B01+801: When charging while stationary, the 48V battery must have a state of charge (SOC) of 70% before the 12V primary battery, or the secondary battery in the case of code 503, can be charged. To ensure optimum battery care, please also comply with the existing Service Information documents regarding the handling of stock vehicles (SI54.10-P-0024A) and on remaining in transport mode (SI54.00-P-0004A) until immediately before handover to end customers. Special note: Do not replace any parts, if the message has occurred due to battery discharge as a result of the driving profile or the ignition being switched on (see attached examples); in such cases separate warranty and goodwill invoicing is not possible, as this is a normal on-board electrical system protection function. Likewise battery care and recharging do not qualify as a W&G case. Please advise customers accordingly regarding the above-mentioned issues relating to vehicle use.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. **NOTE - As of Sept 2025 the pressure testing tool is not finalized and may require modifications to fit properly. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

Cause Vehicles with engine M264 and transmission 725.0 may be equipped with specific software versions. Remedy Update Transmission Software (VGSNAG3). 1. Perform IPR and update transmission control unit software - see list of new software numbers below A0009027479 A0009027579 A0009027779 A0019026209 A0019025909 A0019025809 A0019025609 A0019024809 A0019024309 A0019024709 After updating the software, isolated/intermittent instances of the concern may occur. 2. Perform a standstill adaptation and reevaluate concern. The vehicle can be released if no longer present

Fault code stored P012800-The coolant temperature is below the coolant thermostat specified temperature. Cause Various possible causes Remedy 1- Update HVAC with latest software 2- Perform guided test for fault P012800 and performed repairs per XENTRY diagnosis. - If thermostat requires replacement flush cooling circuit in both directions with 150L of water. MY 2020 GLC350e 253.953 only 3- Update the software of engine control unit N3/10. New version A2749022102 A2749032506. Note- If the guided test passes no repair should be performed. SW update for remaining hybrid models is in development for ME control unit to resolve this fault.

and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (MIL).

Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy **Important** Replacement of the engine wiring harness or control unit is not needed if oil is found at the electrical connection of the crankcase ventilation valve or control unit. Replacement is only allowed if other symptoms or faults are present. Perform either remedy A or remedy B depending on the model Remedy A: SLK/SLC300, C350e hybrid, and GLC350e hybrid Perform guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. Software is not planned for models SLK/SLC300, C350e, and GLC350e. Remedy B: All other vehicles- (Replacement of intake line assembly is not required.) 1- Perform software update for N3/10 Engine control unit. 2- Remove upper engine cover. 3- Unclip ME-SFI control unit (N3/10) with bracket and place to one side with connected lines (see AR07.08-P-7013MRD). 4- Release and disconnect electrical connector (4) of partial-load operation crankcase ventilation valve (Y58/2). 5- Fit cap A094 545 50 03 on electrical connector (4) of engine wiring harness partial load operation crankcase ventilation valve (Y58/2) and ensure correct seating on plug of electrical connector (4). 6- Strap down electrical line (4) of partial load operation crankcase ventilation system valve (Y58/2) at wiring harness. Ensure that electrical line (4) is routed free of tension. 7- Clip in ME-SFI[ ME] control unit (N3/10) with bracket, ensure control unit is correctly seated at attachment points. New software part numbers: 2015-2017 C300 w/722.9 transmission- 2749021202 2749031506 2016-2018 C300 and GLC300 w/725 transmission- 2749021802 2749031806 2019 GLC300- 2749020802 2749031306 2017-2018 E300- 2749021902 2749031906 2019 E300- 2749020702 2749031206 This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy **Important** Replacement of the engine wiring harness or control unit is not needed if oil is found at the electrical connection of the crankcase ventilation valve or control unit. Replacement is only allowed if other symptoms or faults are present. Perform either remedy A or remedy B depending on the model Remedy A: SLK/SLC300, C350e hybrid, and GLC350e hybrid Perform guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. Software is not planned for models SLK/SLC300, C350e, and GLC350e. Remedy B: All other vehicles- (Replacement of intake line assembly is not required.) 1- Perform software update for N3/10 Engine control unit. 2- Remove upper engine cover. 3- Unclip ME-SFI control unit (N3/10) with bracket and place to one side with connected lines (see AR07.08-P-7013MRD). 4- Release and disconnect electrical connector (4) of partial-load operation crankcase ventilation valve (Y58/2). 5- Fit cap A094 545 50 03 on electrical connector (4) of engine wiring harness partial load operation crankcase ventilation valve (Y58/2) and ensure correct seating on plug of electrical connector (4). 6- Strap down electrical line (4) of partial load operation crankcase ventilation system valve (Y58/2) at wiring harness. Ensure that electrical line (4) is routed free of tension. 7- Clip in ME-SFI[ ME] control unit (N3/10) with bracket, ensure control unit is correctly seated at attachment points. New software part numbers: 2015-2017 C300 w/722.9 transmission- 2749021202 2749031506 2016-2018 C300 and GLC300 w/725 transmission- 2749021802 2749031806 2019 GLC300- 2749020802 2749031306 2017-2018 E300- 2749021902 2749031906 2019 E300- 2749020702 2749031206 This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".

- In the speed range up to 45mph - Type of noise: "rattling" / "whirring" / "creaking" Cause Attachment points between strut on shock absorber tower and firewall. Remedy Proceed as described below: 1. Measure the current torque at the rear screws/bolts (strut to bulkhead) and document the result 2. Loosen screw/bolt and move vehicle forwards and backwards approx. 2-3 m (to remove tension) 3. Re-tighten screws/bolts to specified torque (35Nm +/-3.5Nm) 4. Perform test drive and if noise issue is rectified, OK => No further measures required. 5. If the noise complaint is still present after the test drive then measure and document the current torque at the front screws/bolts (strut to spring tower mounting console) 6. Re-tighten to the specified torque value (50Nm+/-5Nm) 7. Perform test drive and if noise issue is rectified, OK => No further measures required. 8. If the noise issue is still present after the test drive, then it is more than likely not related to the mounting of the struts on the body-in-white.

Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy **Important** Replacement of the engine wiring harness or control unit is not needed if oil is found at the electrical connection of the crankcase ventilation valve or control unit. Replacement is only allowed if other symptoms or faults are present. ALL model year SLK/SLC300, C350e hybrid, and GLC350e hybrid Perform guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. Software is not planned for models SLK/SLC300, C350e, and GLC350e. All other vehicles Replacement of intake line assembly is not required. 1- Perform software update for N3/10 Engine control unit. 2- Remove upper engine cover. 3- Unclip ME-SFI control unit (N3/10) with bracket and place to one side with connected lines (see AR07.08-P-7013MRD). 4- Release and disconnect electrical connector (4) of partial-load operation crankcase ventilation valve (Y58/2). 5- Fit cap A094 545 50 03 on electrical connector (4) of engine wiring harness partial load operation crankcase ventilation valve (Y58/2) and ensure correct seating on plug of electrical connector (4). 6- Strap down electrical line (4) of partial load operation crankcase ventilation system valve (Y58/2) at wiring harness. Ensure that electrical line (4) is routed free of tension. 7- Clip in ME-SFI[ ME] control unit (N3/10) with bracket, ensure control unit is correctly seated at attachment points. New software part numbers: 2015-2017 C300 w/722.9 transmission- 2749021202 2749031506 2016-2018 C300 and GLC300 w/725 transmission- 2749021802 2749031806 2019 GLC300- 2749020802 2749031306 2017-2018 E300- 2749021902 2749031906 2019 E300- 2749020702 2749031206 This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".

and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.

Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.

One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case.

Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Model year 2015-2018 Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2015-2018 vehicles. Model year 2019 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".

our customers, Mercedes-Benz USA, LLC ("MBUSA") is extending the warranty coverage on the HV Refrigerant Compressor & Condenser in certain Model Year ("MY") vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles, whichever occurs first, due to the following condition: The copper wire winding in the HV refrigerant compressor might corrode over time and could cause the battery management system to diagnose a lower insulation resistance leading to an insulation error. Due to the physical connection of the HV refrigerant compressor to the HV electrical system, the insulation error would trigger a fault in the entire HV electrical system. A warning message may be displayed (e.g., battery symbol with text malfunction, without restarting engine - visit workshop, towing prohibited see owner's manual) in the instrument cluster. Both electric and combustion engine driving is possible. However, if the driver ignores the visit workshop without restarting a message and switches off the vehicle, it would no longer be able to start.

software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).

our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage for the pressure sensor in certain Model Year (MY) hybrid vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles, whichever occurs first, due to the following issue: The pressure sensor installed on the fuel tank or on the fuel filler neck might detect an electrical error as a result of contaminated fuel, which could cause the check engine malfunction indicator lamp (MIL) to illuminate. Please note, the error can only occur either on the tank or on the filler neck pressure sensor. It cannot occur simultaneously on both sensors. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P1B9D28 Pressure Sensor on filler pipe. P045128 Pressure Sensor Tank. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 47147 Pressure Sensor, Fuel Tank Part(s): A 000 905 59 04 Pressure Sensor (To tank) or- A 000 905 89 16 Pressure Sensor (Filler neck) Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty.

Check engine light may be activated. Various causes Up to Model year 2018 Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the guided test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. If fault code P06DA00 is activating the check engine light, update software of the ME control unit. No further repairs needed if the code no longer activates check engine light after 2 drive cycles. Model year 2019 and later Fault code P06DA00 will activate check engine light as of model year 2019. No driveability concerns will be observed, only illumination of the CEL. This fault code indicates high resistance or open in the circuit to Y130 oil pump control valve. Perform guided test for component Y130 under list of tests in ME. Diagnose location of high resistance or open in Y130 circuit and repair as necessary. Warranty claims submitted without supporting guided test results may be subject to debit.

our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2015 - 2020 C/E/GLC/SLC and SLK vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valve might also increase exhaust gas emission. . Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.

Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. Do not perform software update of N3/10 Engine control unit at this time. This LI will be updated once the software solution is available. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".

our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the intake line assembly in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended,resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valvemight also increase exhaust gas emission. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has amalfunction. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 0101D Solenoid valve, crankcase ventilation system Part(s): A 274 090 5600 80 Intake Line Assembly (inclusive of oil separator, partial load ventilation valve and full-load ventilationvalve.) Where applicable, an ECU software update will be provided for certain vehicle variants. Time Allowed: Intake Line Assembly : 5 hours 40 minutes Software Update: 1 hour Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty.

C-Class (205 platform), E-Class (213 platform) and GLC (253 platform) vehicles, the air conditioning control unit software may not meet production specifications. There is a possibility that a stuck open thermostat may wrongly be detected causing the check engine Malfunction Indicator Lamp (MIL) to illuminate. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will perform a software update to the air conditioning control unit on the affected vehicles.

stored in PTCU (N127) Cause Electric coolant pump communication Remedy 1-Check electric connections on electric coolant pump M75/11 for clean/tight installation. Repair as needed. 2-Update software of MED40 control unit. 3-Replace electric coolant pump M75/11 with part A2742004900.

- Vehicle level is not adjusted correctly, the vehicle possibly leans at an angle Cause Moisture in the compressor freezes at temperatures below zero and may block the compressor. As a result, the starting current when the compressor starts up is too high. Fuse is triggered Remedy Replace compressor, fuse, and relay. Update software and SCN coding. Please invoice the case using damage code 32671 73. Addition: Unscrew pressure line between compressor and valve block and check for moisture. If there is moisture in the pressure line, it can be assumed that there is also moisture in the AIRMATIC valve block. Replace AIRMATIC valve unit.

and 130 km/h over an obstacle. Driving over deeply recessed manhole covers Driving over cross joints Driving over extreme surface undulations 2. Permanent or long-lasting vibrations at specific speed or engine speed noticeable on steering wheel. Roadway surface excitations when DTR+Q is switched on Cause Control oscillations in the electric power steering

The adjustment application by the driver does not correspond to the adjustment direction of the steering column. Cause Polarity reversal of the lines M20/1 (steering column adjustment motor, forward and backward) and M20/2 (steering column adjustment motor, upward and downward) results in a malfunction of the electric steering column adjustment. Remedy Check the lines (line colors) of M20/1 and M20/2 as per the WIS circuit diagram and correct if necessary.

Fault code stored P012800-The coolant temperature is below the coolant thermostat specified temperature. Cause Various possible causes Remedy 1- Update HVAC with latest software 2- Perform guided test for fault P012800 and performed repairs per XENTRY diagnosis.

and 130 km/h over an obstacle. Driving over deeply recessed manhole covers Driving over cross joints Driving over extreme surface undulations 2. Permanent or long-lasting vibrations at specific speed or engine speed noticeable on steering wheel. Roadway surface excitations when DTR+Q is switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68).

Driving over deeply recessed manhole covers Driving over cross joints Driving over extreme surface undulations 2. Permanent or long-lasting vibrations at specific speed or engine speed noticeable on steering wheel. Roadway surface excitations when DTR+Q is switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). If this measure is unsuccessful, do not perform any further repairs. An update will be published as soon as revised software is available

order to detect the fault, please perform the following test steps: 1. Connect manometer of air conditioning service unit in order to read off high pressure and low pressure 2. Connect XENTRY and bring up all climate control actual values in air conditioning menu under "actual values" 3. Set blower to speed 7 4. Set temperature on both sides (driver and front passenger) to LOW 5. Activate AC ON Result 1: Only a small pressure ratio is established (e.g high pressure 7-8 bar; low pressure 5-6 bar). Continue with step (A) Result 2: A larger pressure ratio is established (e.g high pressure 12-16 bar; low pressure 0-2 bar). Continue with step (B) (A): Check the dryer package for black oil and particles. (A.1) Black oil and particles present: Replace refrigerant compressor and valves, flush refrigerant circuit according to instructions in WIS (Refrigerant-only flushing method). Then put system into operation. If the high pressure and low pressure values are OK and the system functions as intended, the vehicle can be returned to the customer. If the pressure ratio is still not correct, continue with step (C) (A.2) No black oil or particles present: continue with step (B) (B): Disconnect vehicle-side power supply for shutoff valve Y19/3 and externally power shutoff valve Y19/3 with 12 V. With the blower setting still set to speed 7, allow the air conditioning system to run. Measure the low pressure while this occurs.

and AMG GT (205, 253, and 290 platform) vehicles, the software for the AMG drive unit control unit does not correspond to the current series production configuration. As a result, noise may occur from the engine mounts. An authorized Mercedes-Benz dealer will update the software as necessary.

C-Class (model series 205), E-Class (model series 213), GLC (model series 253), and AMG GT (model series 290) vehicles cannot be energized after a failure of the acceleration sensors. As a result, noises from the rear axle differential would be noticeable. This is why a software update of the AMG drive unit control unit must be performed in the affected vehicles. The work required for this purpose can be found in the attached work description.

ME

The fault code 162500 (water level message - Bosch) or P226997 (water level message - Delphi) or 171600 (filter load - Bosch) is stored in the engine control unit.

unit

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10P067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Head unit software variant. Remedy For all chassis use Xentry to update head unit (A26/17). Target boot software number should be either: 247 904 6600 (E905.4) OR 247 904 7500 (E906.1) If vehicle fits all criteria and either target software is not available via Xentry, please open an XSS ticket. Damage code 5424x-01 may be used with a repair start date after June 2nd, 2025.

Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.E-Navigator 7.iHeartRadio 8.Traffic Cams Cause Analysis ongoing. Remedy Please track the LI for further updates. Note: Please do not create TIPS cases. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Head unit software variant. Remedy For all chassis use Xentry to update head unit (A26/17). Target boot software number should be either: 247 904 6600 (E905.4) OR 247 904 7500 (E906.1) If vehicle fits all criteria and either target software is not available via Xentry, please open an XSS ticket.

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Under analysis. Remedy For chassis 118, 167, 177, 213, 238, 243, 247, 253, and 293 use Xentry to update headunit (A26/17). Target software number is 247 904 6600 (E905.4). If vehicle fits all criteria and target software is not available via Xentry, please open an XSS ticket.

multifunction display of the instrument cluster while driving (see picture in attachment). Cause On vehicles with HERMES 3.0 currently, A2389015700 A2389015800 A2389018400 A2389018900 A2389019000 A2389019800 A2579011200 A2579012100 the above-mentioned message is sporadically displayed in the instrument cluster once the over-the-air updates to software release E843 (software part number A2389022409) have been performed. The issue is currently being analyzed; the cause is still unclear. Remedy Please manually commission the control unit N112/9 (HERMES) using XENTRY: XENTRY. "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit" Invoice the required work using damage code 8251M/01 (damage location/damage type).

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Under analysis. Remedy For chassis 118, 167, 177, 213, 238, 243, 247, 253, and 293 use Xentry to update headunit (A26/17). Target software number is 247 904 6600 (E905.4).

B19C804 "Software tampering has been detected. There is an internal fault". </p> <p> </p> <p> Note: If there are no relevant customer complaints, then the DTC can be ignored as it does not directly affect functionality. If there is a customer complaint in addition to the above DTC, further diagnostic measures must be performed. </p> Cause The current software release of the MBUX multimedia system (A26/17) Remedy <p>Update the A26/17 to newest available software release.</p><p> </p><p>Note: Do not replace any parts.</p>

control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.

Temperature setting in Mmc mobile application settings incorrect Remedy Adjust the setting in the Mercedes me connect app via mobile phone (settings -> units)

Stations&#34; or a different category. Sometimes, the &#34;My Favorites&#34; category will be unavailable for the entire drive cycle. Cause Current MBUX Multimedia System (A26/17) software release Remedy Software update of MBUX Multimedia System (A26/17) to E905.4 (in development). This document will be updated once the software is released.

and/or stored in the MBUX Multimedia System (A26/17) Cause Current MBUX Multimedia System (A26/17) software release Remedy If there is no customer complaint present, the DTC can be ignored. A future MBUX Multimedia System (A26/17) software release (E905.3) will prevent the DTC from occurring. This document will be updated when the software is available.

show the following message: "Map data does not match with your system. Please insert a medium containing the corresponding map data". the navigation menu cannot be opened "Activating..." is displayed beneath the navigation icon in the main menu or above the map display "Traffic Sign Assist Inoperative" message in the instrument cluster display The map data update cannot be carried out (on vehicles with code 2U0 car2go) Cause Navigation database was not successfully activated Remedy Perform the proposed measure in order to remedy the complaint: Ensure the MBUX multimedia system (A26/17) software is up-to-date (E870.9 or newer) Perform a user data reset ("Settings" -> "System" -> "Reset" in the MBUX display). Check functionality. If the complaint remains then continue with next steps Open the Dealer menu by pressing and holding down the "Home" and "Radio/Media" buttons simultaneously for approximately 8 seconds When in the Dealer menu, select "Navigation" - Then select "Delete MapData" Close the Dealer menu and reinstall the currently available NTG6 map data version from Download Manager COMAND/Hard-Disk navigation via USB Perform SCN coding of the MBUX multimedia system (A26/17) Check navigation functionality

Please insert a medium containing the corresponding map data". the navigation menu cannot be opened.

The contact list may not be fully populated and in some instances, the call list will display telephone numbers but no names.

while attempting to communicate with the MBUX multimedia system (A26/17)

without user input and does not provide any audio notification. - The MBUX multimedia system (A26/17) does not give any spoken or visual driving instructions. Only the destination information and the current route are shown in the MBUX multimedia system (A26/17)

the mobile phone is briefly lost

See example file in the attachments area: "MRSMSchleifgerusch_SCCMGrindingNoises. MOV". Cause Under analysis. Remedy Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: Loosen screws of the MRSM/SCCM and steering wheel, realign the MRSM/SCCM, and refasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: When installing the MRSM/SCCM, make sure that no damage occurs! If the noise is due to the steering wheel (see attachment "LenkradSchleifgerusch_SteeringWheelGrindingNoises.mp4"), please use LI46.10P077313. Only disassemble and mount all component parts in the "straightahead position" (see also WIS). Please refer to this LI in the "Notes" section of the warranty claim!

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by doubleclicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

control unit (N112/9) is not supported for gray-market vehicles. Cause Before deactivating the HERMES control unit (N112/9), it must be clarified by the legal department of the respective MPC whether and under what conditions deactivation may be carried out. If deactivation is not permissible under applicable law, the HERMES control unit (N112/9) must not be deactivated. Remedy Please inform the customer that, following deactivation, the vehicle will no longer be able to place an automatic emergency call, nor will the customer be able to place a manual emergency call. After deactivation, the Mercedes-Benz Digital Extras will also no longer be available. Please have the attached sample form checked by your market's legal department, adapted to local requirements if necessary, and approved. Furthermore, after informing the customer about the effects of deactivation, please have the workshop complete and sign the approved form together with the customer, and send it to the MPC via a TIPS case for audit-compliant documentation. Furthermore, the workshop must affix a sticker to the emergency call button cover on the overhead control panel and to the emergency call button itself. After affixing, pictures of the overhead control panel need to be attached to the TIPS case for audit-proof documentation. After deactivation, the HERMES control unit (N112/9) is in the "Out of Service" operating status, and the display "SOS NOT READY" appears in the Audio/COMAND system. This display message tells the customer that the emergency call function is not available. In detail, the following steps must be carried out 1. The workshop must inform the customer about the effects of deactivation (see above) 2. Legal review by the MPC Legal department to determine whether deactivation is permissible for the vehicle and provision of a market-specific customer form based on the examples (see "Example - Deactivation communication module HERMES customer declaration English V3.0.pdf") 3. Completion of the market-specific customer form by the workshop and obtaining the customers signature 4. Creation of a XSS ticket by the workshop for the MPC with the signed customer form attached 5. Written confirmation of legally reviewed and approved deactivation by the MPC in the TIPS case (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, point 1) 6. Creation of an XSS ticket for documentation of the SA code "09o" (zero nine oh) in the Vehicle Documentation System (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, steps 27) 7. Ordering of stickers (part number A9078172900), quantity: 2 8. Affixing of the sticker (part number A9078172900) to the cover of the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 9. Affixing of the sticker (part number A9078172900) to the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 10. Taking photos of the applied stickers and attaching them to the TIPS case 11. After the XSS ticket has been successfully processed, the communication module must be deactivated using XENTRY: Connect XENTRY Diagnosis Access the HERMES control unit (N112/9) "Adaptation" tab, menu item "Teach-in processes" -> "Deactivation" Follow the instructions

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

wiring harness and connectors from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles for certain Model Year (MY) 2016-2019 Mercedes-Benz E-Class and GLC-Class vehicles (213, 238, and 253 platforms). This extended warranty is applicable to the following vehicles: This warranty extension applies to the electrical wiring and plug connection on the accelerator pedal, as it may not meet current production specifications. The extended warranty will be indicated in VMI under Service Packages.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage detection (DMTL) on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership.

message "SOS - Service not activated" is displayed in the instrument cluster. Cause The message "SOS - Service not activated" tells the customer that "over-the-air" registration of the vehicle with the Mercedes Intelligent Cloud is not possible. On a gray import vehicle, this is due to the fact that the SIM card installed in the HERMES communications module cannot dial into the mobile phone network in the importing country. Remedy The only way of avoiding the message in the instrument cluster is to deactivate the HERMES module using the 09o deactivation process after obtaining the customer's consent. After deactivation, the HERMES control unit (N112/9) has the operating status "Inoperative". The message "SOS not ready" appears in the audio/COMAND display (A40/8) and may also appear in the instrument cluster. This display message tells the customer that the emergency call function is not available. In addition, the workshop must attach a label (2 x part number A9078172900 required) to the cover of the emergency call button in the overhead control panel and to the emergency call button itself. Replacing the hardware of the HERMES communication module is not effective.

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: vehicle technical issue? customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge, create a TIPS case. -Must include with the case: Amperage setting of charger and time battery was on charger XENTRY Battery Tester results Voltage of battery taken with multimeter: Do not connect charger while taking measurements N10/6 FSAM and N73/3 EZS CUL Workshop analysis of conspicuous data Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

Fault code in N10/8 - rear signal acquisition and actuation module in the quick test: B164B49 The rear right turn signal lamp has malfunctioned. There is an internal electrical fault. and/or B164A49 The rear left turn signal lamp has malfunctioned. There is an internal electrical fault. Cause Sensitive fault detection in N10/8 - rear signal acquisition and actuation module (BC_R) Remedy 1. Check rear lamp for failure of the individual LEDs In the event that an LED fails, the rear lamp must be replaced 2. Check the software release of the Rear SAM (BC_R) and update if necessary 3. Add AO code "o70" via VeDoc 4. Perform SCN coding of Rear SAM (BC_R). 5. If concern occurred on left, use damage code 82C20 73 6. If concern occurred on right, use damage code 82R20 73

CLA, CLS, E-Class, G-Class, GLA, GLB, GLC, GT, and S-Class (118, 177, 205, 213, 217, 222, 238, 247, 253, 257, 290, 463 platform) vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update. Parts Parts are not required

control units FSCM_GEN4/5/6 For these fault codes, the tests contained in XENTRY must be carried out P046109 / P206609 / P13E600 For these fault codes, the connector couplings/wiring harness routing must be checked for damage P206600 / P046100 Cause Various Remedy Carry out XENTRY tests for the listed fault codes in the FSCM (N118) and document the monitor graphics for the primary/ secondary lever-type sensors.

Please note that if the complaint "Fuel filler flap not opening" occurs, it is important to check the fuel filler flap before replacing the central locking actuator. For gasoline hybrid vehicles where the fuel filler flap fails to open or does so but slowly, observe the document "Fuel filler flap fails to open or does so but slowly on plug-in HYBRID gasoline vehicles"! Cause Central locking actuator may have an electrical fault and may not open. Remedy 1. Car locked: To rule out incorrect operation, operate the fuel filler flap in the area shown in Fig. 1 and listen out for the clicking noise of the microswitch in the central locking actuator. If no clicking can be heard, continue with point 4. 2. Car unlocked: Press area on flap to start the microswitch clicking. Flap opens - show the customer the area to press. 3. Car unlocked: Flap cannot be opened regardless of which area you press. Open the flap by operating the emergency release for the CL actuator (through trunk, fender gap cover, etc, depending on specific vehicle) 4. Central locking actuator pressed directly, no clicking of microswitch, no electrical release of central locking actuator => Clicking of microswitch, electrical release of central locking actuator => Tank filler recess/charging recess not OK; report results via a TIPS case to B/C/E Inbox. 5. Replace central locking actuator; check function of new part before installing it: Do not dispose of damaged part. New central locking actuator does not release: More detailed examination of connector coupling, wiring harness, electrics required.

control units FSCM_GEN4/5/6 For these fault codes, the tests contained in XENTRY must be carried out P046109 / P206609 / P13E600 For these fault codes, the connector couplings/wiring harness routing must be checked for damage P206600 / P046100 Cause Various Remedy Carry out XENTRY tests for the listed fault codes in the FSCM (N118) and document the monitor graphics for the primary/ secondary lever-type sensors.

Cause Quick test shows FC P0A7F00 The state of health limit of the hybrid/high-voltage battery module has been reached. No drivability concerns occurred and vehicle drives as normal. Remedy Do not replace any parts!! 254: SW has been released. Ensure all Add-ons are installed. Update A66 with the latest SW A 000 903 51 75 MY24 206: SW has been released. Ensure all Add-ons are installed. Update A66 with the latest SW A 000 903 52 75 After SW has been updated, perform the following reset procedure: Step 1: Read the State of Health Resistance - (SOH-R) Step 2: If SOH-R <=125%: Clear fault memory in PTCU(N127) and 48V battery (A66). Procedure finished. If SOH > 125%: Drive for a duration of 60 minutes to retrain the SOH-R value. Step 3: Read the State of Health Resistance - (SOH-R) If SOH-R <=125%: Clear fault memory in PTCU(N127) and 48V battery (A66). Procedure finished. If SOH > 125%: Park vehicle in Workshop for >12 hours in warm ambient temperature >60F, afterwards drive for a duration of 60 minutes. Step 4: Read the State of Health Resistance - (SOH-R) If SOH-R <=125%: Clear fault memory in PTCU(N127) and 48V battery (A66). Procedure finished. If SOH-R is still >125%, open a TIPS case.

Cause The following information is being provided for educational purposes only: At Mercedes-Benz, we believe that our vehicles should display to the driver a range that in all probability can actually be achieved. These ranges are predictions - the range actually achieved may therefore differ from the range shown. The calculation for the predicted range takes into account the current outside temperature, the set temperature of the air conditioning system, the battery capacity and the characteristics of previous journeys (sporty/anticipatory driving style). Where previous journeys are concerned, factors given particular consideration are individual driving style and the use of other power consumers (seat heating, lights, charging function for smartphones, etc.). It is therefore possible that data from the last few hundred kilometers driven is also used in the calculation. Consequently any change in usage behavior will only slowly affect the predicted range. If active navigation or active commuter route is used, additional information about the route ahead (for example elevation profile, traffic volume) can be included in the range calculation. Remedy The customer's individual input to the range can be reset. Depending on the vehicle, the reset can be done in the instrument cluster or the head unit. For plug-in hybrid vehicles of model series 166 (all), 205 (up to modification year 18/1), 213 (up to modification year 17/2), 222 (up to modification year 17/2), 253 (up to modification year 19/1), the range can be reset by resetting the trip computer ("From reset", "From start" and "Day cycle counter"). After the reset, a value based on the certified range will be shown. For electric and plug-in hybrid vehicles of model series 205 (from modification year 18/2), 213 (from modification year 18/1), 222 (from modification year 18/1), 253 (from modification year 19/2) and model series 118, 167, 177, 206, 223, 247, 293, 295, 297 a reset is only possible by resetting the head unit to the factory settings. This will delete all saved customer data and any settings made (e.g. radio settings, navigation destinations). If necessary, therefore, back up the customer data onto a USB flash drive using the Backup function before performing a reset. As from vehicles with NTG 7, Mercedes me is used for the making the backup. After the reset, an empirical value is displayed that is based on normal use of the vehicle and the current climatic conditions (set temperature and outside temperature - commensurately higher values will be achieved if the air conditioning system is switched off). Depending on driving style, outside temperature and which power consumers are actually switched on, the achieved range may significantly exceed this range, but likewise may also fall significantly short of it. Further information on battery capacity and aging can be found in document SI47.70-P-0070A.

Make sure to follow the operation steps exactly as described in XENTRY Diagnosis. Use a battery charger to ensure sufficient power supply of the vehicle on-board electrical system battery (greater than 12.5 V). If XENTRY Diagnosis is already connected to the vehicle, start with operation step 2. If two or more software updates or SCN codings are performed during one workshop visit, operation items 02-4762 and 02-5058 may be invoiced only once for each workshop order. Work procedure 1. Connect XENTRY Diagnosis. 2. Update N129/1 - power electronics (SG-EM) control unit software. To do this, select menu item "Quick test view N129/1 - power electronics (SG-EM) Adaptations Control unit update Update of control unit software". Then follow the user guidance in XENTRY Diagnosis. 3. Disconnect XENTRY Diagnosis.

CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.

A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.

Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!

steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.

C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customers vehicle. The OTA may be validated as successful on the customers Mercedes Me connect app under Over-the-Air Vehicle Updates as Update for the communication module. If the OTA is successful it will show a green installed and date of installation in the Over-the-Air update section.

wiring harness and connectors from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles for certain Model Year (MY) 2016-2019 Mercedes-Benz E-Class and GLC-Class vehicles (213, 238, and 253 platforms).

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy Follow guided tests as described.

heard coming from the area of the instrument panel or the driver's footwell.

OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: Hitting the curb/posts with the front wheels. Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). Cracks (1) High pressure cleaner (2) Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

May be most noticeable when transitioning from a coasting condition to accelerator pedal application. May occur in all drive modes. Cause Dualclutch transmissions (DCT) inherently exhibit more dynamic shifting behavior compared to other types of transmissions. This is due to the use of physical clutches for starting and gear changes. In certain situations, dynamic driving behavior can lead to a slight jerk sensation which is a normal technical characteristic of the transmission. A typical example is a "Change of Mind" situation: The customer is coasting towards a red traffic light. The traffic light turns green while the vehicle is still coasting. The customer then presses the accelerator pedal. In these situations, a slight jerk may occur briefly because the transmission must quickly engage the appropriate gear and control the clutches accordingly. Since shift forks are responsible for engaging the gears during shifting, a slight shifting noise may also be noticeable. Please note driving programs S, S+, and M are designed to provide sportier vehicle behavior and are not optimized primarily for maximum comfort, so this operation may be more audible. Remedy Verify the customer's concern and confirm proper transmission operation. If no faults or abnormal operating conditions are identified by IPR (Intelligent Predictive Repair), no hardware replacement is necessary. Inform the customer that the transmission has been designed to provide direct gear engagement and responsive vehicle performance. Under certain operating conditions, brief shift sensations may be perceptible and are consistent with the operating characteristics of the dualclutch transmission

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

The clunk is heard once when changing from forward to reverse (and vice versa). Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

This may cause noises (clattering/vibrating) at the underbody. Cause Due to insufficient holding ability of the catch tab at the underbody cable duct, the cable duct may become unhooked. Remedy Perform a visual check of the cable duct and the attachment point. Apply a high-temperature cable tie (see remedy and parts).

This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.

This may cause noises (clattering/vibrating) at the underbody. Cause Due to insufficient holding ability of the catch tab at the underbody cable duct, the cable duct may become unhooked. Remedy Perform a visual check of the cable duct and the attachment point. Apply a high-temperature cable tie (see remedy and parts).

with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Steering column height adjustment transmission 2. Seat control unit software Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit

Individual or all tire pressure sensors are not recognized. Tire pressure monitoring system nonfunctional / temporarily unavailable. Cause Tires with excessively-large radio signal attenuation interfere with transmission of the tire pressure sensors. Remedy Check if one of the following tires is installed: If one of the tires listed above is installed with the corresponding DOT number, replace this tire. In accordance with the Warranty Manual, the costs for the tire shall be settled directly with the tire manufacturer.

Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.

GLE-Class (253, and 292 platform) vehicles, the automatic transmission does not meet specification, and thus the possibility exists that a hard and delayed shift operation may occur.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

TIREFIT sealant bottle may not meet specifications. The possibility exists that the sealant bottle may leak or may have otherwise been removed from the vehicle. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk.

Cause Possible tolerance complaint regarding the door handle Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3).

Cause Alignment of door handle bearing bracket is not correct. Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace the door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3).

Cause Possible tolerance complaint regarding the door handle Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3).

Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead.

protective coating (due to poor original optimization of coating) of door beltline trim strips, door upper trim strips and side window trim element. Remedy 1. Check if the complaint cannot be rectified by polishing the trim bars with the polish. 2. If the complaint cannot be rectified, replace the door beltline trim bars, door upper trim bars and rear side window with trim element with optimized protective coating.

protective coating of door beltline trim strips, door upper trim strips and side window trim element due to strong alkaline detergent in car washes. Remedy 1. Check if the complaint cannot be rectified by polishing the trim bars with the polish. 2. If the complaint cannot be rectified, replace the door beltline trim bars, door upper trim bars and rear side window with trim element with optimized protective coating.

NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not preauthorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Axle Half Shaft noise when changing direction - Front) LI33.30-P-056665 (Axle Half Shaft noise when changing direction - Rear) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles in the below FIN range. FIN range up to: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Axle Half Shaft noise when changing direction - Front) LI33.30-P-056665 (Axle Half Shaft noise when changing direction - Rear) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range above): 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.

Cause Until now the rear axle shock absorber support bushing was only available together with the rear axle shock absorber as a replacement part. In future, the rear axle shock absorber support bushing will be available individually as a replacement part to avoid any unnecessary shock absorber noise. Remedy For noise problems on the rear axle shock absorbers, please always make a noise diagnosis, for example using Chassis Ear to localize any sources of noise on shock absorbers or support bushings. If the noise originates from the upper part of the shock absorbers, it is enough to replace the support bushings. Otherwise the complete shock absorber including support bushing have to be replaced. The modified support bushings must be replaced in pairs the first time so that any mixed installation of old and new is reliably ruled out.

existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 9, 2026. After July 9th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

instructions on how the HVAC Service Warranty repair must be carried out. To enhance the satisfaction of our customers, avoid further costs of litigation, and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew odors originating from the HVAC system. Although the settlement has received court approval, warranty coverage will not take effect until December 7, 2020, when the appeal period for class members will have expired. If the settlement takes effect, warranty coverage will include cleaning of the evaporator and replacement of the HVAC filters.

Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Cause Aluminum cassette scrapes on the inside of the end cap. The contact point causes creaking noises. Remedy Disassemble end caps of load compartment cover by pressing the guide pins (see attachment) inwards and removing the end caps. Cut 2 felt strips to required size of 25 mm/15 mm/1 mm (length/width/height). Glue a piece of felt (see attachment) to each top corner in the direction of the roller blind outlet (left and right side). Then reinstall the end caps with springs.

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. Cause Under Investigation Remedy Under investigation. One option is to turn off Traffic Sign Assist until the investigation is completed. Once completed this LI will be updated. No TIPS case is necessary. Do not replace parts.

The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.

nonfunctional

periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!