2013 Mercedes-Benz G550 TSBs

our customers, Mercedes-Benz USA ("MBUSA") is extending the coverage for the exhaust valve assembly on your vehicle as follows: Why the warranty extension? On certain Model Year 2011-2016 CL/CLS/S/E/ML/SL/G/GL/GLE-Class vehicles with V8 engines, the exhaust valve assembly might not work properly and result in an engine misfire and potential illumination of the check engine Malfunction Indicator Lamp ('MIL'). Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be covered under this extended warranty and performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to additional expenses as identified in the Service and Warranty Information booklet.

and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

(EHS) or of repair kit controller unit (VGS). Cause The wrong older A-code ("Generation EHS") is documented in VeDoc for the newly installed transmission or the newly installed electrohydraulic controller unit (EHS)/repair kit controller unit (VGS). Old VGS2 hardware A0335457332 (from quick test) New VGS3 hardware A0034460310 or A0009018008 (from quick test) Remedy Delete the old A-code and redocument the new A-code in VeDoc, then perform commissioning. A. If Diagnosis at the vehicle is possible: To determine the correct EHS item number, the currently installed EHS/VGS hardware should be read out first: In XENTRY Diagnostics via the tab "Control unit view" - "Current quick test" - "Fully integrated transmission control" - "EHS part number". Order the new EHS with this read-off item number. DAS: "Quick test" - "EGS - Electronic transmission control serial number". Order the new EHS with this read-off serial number. B. If Diagnosis at the vehicle is no longer possible, The number must be read off directly from the EHS, and the ordering process must be initiated using this number. Exception: For engine 629 with transmission 722.9, EHS A220 270 24 06 must be installed. Read-off part number is A 220 270 12 06 In this case, the following must be observed for making a correct order: Exclusively for model 219.356, 171.456 with transmission 722.906 up to and including model year 2005 (code 805) A 220 270 12 06 is no longer available --> Please install EHS A220 270 27 06 and document A92 in Vedoc If this does not work, please open a TIPS case and provide both the original EHS part number/A code and new EHS part number/A code Read-off part number + old A-code in VeDoc --> EHS item number and new A-code ("Generation EHS") J valve body plate with VGS3 old A-code A28/A29: A2202701306 + code A28/A29 --> A2202702706, delete code A28/A29 and document A92 in VeDoc A2202701406 + code A28/A29 --> A2202702706, delete code A28/A29 and document A92 in VeDoc A2202701206 + code A28/A29 --> A2202702706 delete code A28/A29 and document A92 in VeDoc O valve body plate with VGS3 old A-code A45: A2202701206 + code A45 --> A2202702906, delete code A45 and document A94 in VeDoc A2202701406 + code A45 --> A2202702906, delete code A45 and document A94 in VeDoc A2202702106 + code A45 --> A2202702906, delete code A45 and document A94 in VeDoc P valve body plate with VGS3 old A-code A46: A2202701906 + code A46 --> A2202703006, delete code A46 and document A97 in VeDoc A2202702206 + code A46 --> A2202703006, delete code A46 and document A97 in VeDoc N valve body plate with VGS3 old A-code A39: A2202701206 + code A39 --> A2202703106, delete code A39 and document A95 in VeDoc A2202701406 + code A39 --> A2202703106, delete code A39 and document A95 in VeDoc A2202701806 + code A39 --> A2202703106, delete code A39 and document A95 in VeDoc M valve body plate with VGS3 old A-code A38: A2202701406 + code A38 --> A2202703206, delete code A38 and document A96 in VeDoc A2202701906 + code A38 --> A2202703206, delete code A38 and document A96 in VeDoc K valve body plate VGS3 with old A-code A30: Old A-code A30 --> delete code A30 and document A93 in VeDoc N valve body plate VGS3 with old A-code A27: Old A-code A27 --> delete code A27 and document A95 in VeDoc

with Easy Entry function), noise (breakaway noise) when leaving the limit stops of the height adjustment. Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Driver seat control unit software 2. Steering column height adjustment transmission Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Perform software update of driver's seat control unit 2. Replace repair kit for steering column height adjustment Procedure 1: Perform software update of driver seat control unit. ALL models except 205/253/293/222/217/231/463/213/238/257/290 up to special equipment code 801. Move out the fore/aft adjustment to the end position. Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward After releasing the jam, perform a software update of the driver's seat control unit If procedure 1 is not effective, there is no new software available for the driver seat control unit, or the chassis is not listed above (167, 223, 294, 206, 294, 295, 296, 297,232,214,254) then use procedure 2. Procedure 2: Replace repair kit for steering column height adjustment. Move out the fore/aft adjustment to the end position. Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward Remove footwell trim on driver's side. Determine type version of height adjustment in XENTRY Parts Information and order appropriate replacement part (refer to attachment). 1. Version A: A 231 460 77 00 2. Version B: A 205 460 38 03 Remove steering column. Remove height adjustment (adjustment repair kit). Install repair kit (adjustment repair kit) (observe tightening torque for screws in attachment). Install steering column. If possible, flash driver seat control unit to latest software release or code SCN again. Commission driver seat control unit (normalization of limit stops is deleted and learning process repeated).

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.

that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.

Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

the exhaust valve assembly might not work properly and result in an engine misfire and potential illumination of the check engine Malfunction Indicator Lamp (MIL).

vehicle.

The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).

Fault code 20BE1B and/or 20BD1B (The heating element of the AdBlue tank has a malfunction) is logged in the Blue-Tec control unit.

Fault code 20BE1B and/or 20BD1B (The heating element of the AdBlue tank has a malfunction) is logged in the Blue-Tec control unit.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

Cause The parking sensors are detecting the front brush guard. Remedy Complaint must be consistently reproducible and can occur multiple times a key cycle without obvious cause. NOTE: The parking system serves solely as an aid. Please review both the system function and system limitations as shown in the Operator's Manual. Certain environmental factors can affect system functionality such as hot exhaust gases or extreme heat, sensor interference, or other outside influences or aftermarket modifications. If after verifying the complaint is consistently reproducible: 1. Determine if the complaint is reproducible only in high ambient temperatures. If complaint does not occur in cooler ambient temperatures, it is due to system limitations. You may proceed with the below work but the vehicle may be released afterwards as it is due to system limitations. 2. Remove the brush guard and verify the park distance sensors function as expected. 3. Reinstall brush guard and adjust so that it is as far away from the park sensors as possible. Typically only small adjustments are possible. 4. Check function. If the concern is still consistently reproducible, please apply clear matte film to the locations as shown below at a minimum, although the clear matte film may be applied to the whole brush guard. Picture: Above shown is the 465 brush guard variant. Although similar to the 463, there are some key differences such as the 465 being fitted with a front camera.

Cause The parking sensors are detecting the front brush guard. Remedy Complaint must be consistently reproducible and can occur multiple times a key cycle without obvious cause. NOTE: The parking system serves solely as an aid. Please review both the system function and system limitations as shown in the Operator's Manual. Certain environmental factors can affect system functionality such as hot exhaust gases or extreme heat, sensor interference, or other outside influences or aftermarket modifications. If after verifying the complaint is consistently reproducible: 1. Determine if the complaint is reproducible only in high ambient temperatures. If complaint does not occur in cooler ambient temperatures, it is due to system limitations. You may proceed with the below work but the vehicle may be released afterwards as it is due to system limitations. 2. Remove the brush guard and verify the park distance sensors function as expected. 3. Reinstall brush guard and adjust so that it is as far away from the park sensors as possible. Typically only small adjustments are possible. 4. Check function. If the concern is still consistently reproducible, please apply clear matte film to the locations as shown below at a minimum, although the clear matte film may be applied to the whole brush guard.

Cause The parking sensors are detecting the front brush guard. Remedy Complaint must be consistently reproducible and can occur multiple times a key cycle without obvious cause. NOTE: The parking system serves solely as an aid. Please review both the system function and system limitations as shown in the Operator's Manual. Certain environmental factors can affect system functionality such as hot exhaust gases or extreme heat, sensor interference, or other outside influences or aftermarket modifications. If after verifying the complaint is consistently reproducible: 1. Remove the brush guard and verify the park distance sensors function as expected. 2. Reinstall brush guard and adjust so that it is as far away from the park sensors as possible. Typically only small adjustments are possible. 3. Check function. If the concern is still consistently reproducible, please apply clear matte film to the locations as shown below at a minimum, although the clear matte film may be applied to the whole brush guard.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Cause: The noises occur due to insufficient greasing of the steering column adjustment guide. Remedy: Disassemble bellows of steering column tube module. Move steering column entirely out and entirely down. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). Move column up 1/4 of the way and grease again. Continue until upper limit stop is reached. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. If noise does not resolve, perform above procedure again. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. If noise still does not resolve, please open a TIPS case.

message "SOS - Service not activated" is displayed in the instrument cluster. Cause The message "SOS - Service not activated" tells the customer that "over-the-air" registration of the vehicle with the Mercedes Intelligent Cloud is not possible. On a gray import vehicle, this is due to the fact that the SIM card installed in the HERMES communications module cannot dial into the mobile phone network in the importing country. Remedy The only way of avoiding the message in the instrument cluster is to deactivate the HERMES module using the 09o deactivation process after obtaining the customer's consent. After deactivation, the HERMES control unit (N112/9) has the operating status "Inoperative". The message "SOS not ready" appears in the audio/COMAND display (A40/8) and may also appear in the instrument cluster. This display message tells the customer that the emergency call function is not available. In addition, the workshop must attach a label (2 x part number A9078172900 required) to the cover of the emergency call button in the overhead control panel and to the emergency call button itself. Replacing the hardware of the HERMES communication module is not effective.

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: vehicle technical issue? customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge, create a TIPS case. -Must include with the case: Amperage setting of charger and time battery was on charger XENTRY Battery Tester results Voltage of battery taken with multimeter: Do not connect charger while taking measurements N10/6 FSAM and N73/3 EZS CUL Workshop analysis of conspicuous data Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware ISU = Initial Start Up LVDS = Low Voltage Differential Signal NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465, 906 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" No vehicles currently launched.

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy Follow guided tests as described.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10P067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.

Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.E-Navigator 7.iHeartRadio 8.Traffic Cams Cause Analysis ongoing. Remedy Please track the LI for further updates. Note: Please do not create TIPS cases. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

The contact list may not be fully populated and in some instances, the call list will display telephone numbers but no names.

B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software

message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

The deadline for all dealer returns is no later than Thursday, April 23, 2026. After April 23rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommissioning of the HERMES control unit (N112/9) using XENTRY Diagnosis version 12/2025. This is mandatory: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

informing them that they need to have an i-button call performed to ensure their mbrace device has registered with the Verizon Telematics systems. If the i-button call failed or if the customer was unable to perform the i-button call, the mbrace agent instructed the customer to make an appointment with their dealer to have the issue corrected and/or i-button call performed. The vehicles impacted range from model year 2002 to 2014.

speeds Cause The airstream can excite the rubber strip of the windshield to whistle. Note: To troubleshoot, tape down the strip. Remedy Seal the lower lip of the rubber strip at the top of the windshield in the installed state across the entire width with window adhesive.

Cause The airstream can excite the rubber strip of the windshield to whistle. Note: To troubleshoot, tape down the strip. Remedy Seal the lower lip of the rubber strip at the top of the windshield in the installed state across the entire width with window adhesive.

Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.

See figure A for example. Cause The insert (breathable filter) is designed to be inside for dust protection and air flow control. Remedy Do not remove the breathable filter from the microphone assembly. This part is designed to be in the microphone and should remain in the vehicle. Note: If TIPS support is required for microphone symptoms please open a TIPS case and reference this LI.

NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not preauthorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify.

on the instrument cluster during startup or while driving AND stored DTC in quick test U0416FE - "Implausible data were received from control unit Traction system" in A108/1 (Distronic). Cluster messages will remain and mentioned system functionality is limited until key is cycled. Cause Under investigation. Symptom may occur with one or a combination of the following: 1. Low battery health 2. Battery state of charge 3. Repeated short drive cycles. Cluster messages will resolve after a vehicle key cycle. Remedy Please open a TIPS case with: Quick test A108/1 (Distronic) control unit log Instrument cluster message memory Driving Battery Cycle "Individual values while driving" Log (Front SAM) Battery health Battery state of charge

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CPR = Car Package Release (For MB.OS) CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

See arrow direction in attached pictures. Cause Slipped thrust bearing ring on the height adjustment. Remedy Install repair kit for height adjustment of the steering column. For tightening torque, see attachment.

cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: Fluid intrusion Broken bushings or physical damage See attachments. Remedy If a component needs replacement without visible external damage, submit a detailed TIPS case. Include information on all connected external devices (e.g., charging cables, USB drives, hard drives).

Cause In the area of the rounding at the D-pillar, a leakage may occur between the rear side wall and the roof paneling. Remedy Troubleshooting: Locate the area of the leak by performing a pressure test and using leak detector spray or soapy water. To do this, tape up the rear vents on the D-pillars and set the ventilation system to the maximum blower setting. If leaks are verified, proceed with sealing of the drip rail: 1. Remove the corner seal strip of the drip rail (see AR88.80-P-4005XG). 2. Clean and apply primer to the marked areas (see figure 1). 3. Replace the corner seal strip and fill with sealant, then mount it straight onto the flange. 4. Remove any excess adhesive and Install outer drip rail. Apply adhesive to inside corner. 5. After installing the drip rails, perform a water test (approx. 0.5 hours).

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.

Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters

nonfunctional

periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!