2024 Mercedes-Benz EQB 250+ TSBs

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by doubleclicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module NOTE: Occasionally to verify complaint, the steering column/vehicle needs to be in direct sunlight or hot conditions for a few hours. If noise only occurs when adjusting the steering column via electric actuation, please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on all pivot points including, but not limited to, green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, wipe excess grease off and perform greasing and movement to limit stops in all directions again. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. Include detailed items of the following: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again and anywhere there are movement or friction points that the noise seems to be emanating from. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

the journey Workshop findings: Refrigerant line between refrigerant compressor and condenser is cracked If listed line is cracked, please conduct the following tests 1. Are the fault codes B19A200 or P053400 current or stored in air conditioner control unit N10*1? 2. Check dryer cartridge at condenser for particles: Remove dryer cartridge, illuminate inlet of dryer cartridge using flashlight (A), and examine filter screen through outlet of dryer cartridge (B) -> see comparison picture bad/good Further possible signs for this fault profile are: Refrigerant level clearly too low (target: 670 g): In this case, please first of all check where a leak is present in the system Loud noises from compressor: If loud noises are coming from the compressor, this finding must be validated with the two tests specified above (check the dryer cartridges or the specified fault codes). Loud noises alone are no reason to replace the compressor, since these can be very subjectively perceived in individual cases. Cause The refrigerant line between the A/C compressor and capacitor may be damaged due to a high refrigerant temperature. Remedy If the tests listed have been carried out and the results correspond to the described fault profile, please carry out the following steps: If the tests listed have been carried out and the results correspond to the described fault profile, please carry out the following steps: 1. Flushing of the refrigerant circuit as per AR83.30-P-1785EQA 2. Then replace the following parts: A/C compressor (***IMPORTANT: If the A/C compressor A0008304404 or A0008307704 is installed in the vehicle, it must be replaced by part number A0008307804***) If the capacitor A0998301100 is installed, then replace the complete capacitor (including dryer cartridge and PT sensor). If capacitor A0998301400/1500 is installed, only new dryer cartridge (A2938350500) Refrigerant line between refrigerant compressor and capacitor (A2438308600) 3. To use the new refrigerant line A2438308600, the electric line for pressure sensor B161/2 must be extended using the adapter wiring harness A2435408724. Disconnect plug from pT sensor Route the adapter line A2435408724 to the newly positioned pT sensor and secure it with a cable tie to prevent chafing 4. Insert the blind plug from the adapter wiring harness onto the old sensor. 5. Check SAM (N10) for latest software. If necessary, perform software update. 6. Finally, please check whether all heating and cooling functions are working; if not, please create a TIPS case with the following information: Detailed description of the customer complaint and the workshop measures carried out Initial quick test Photos of the filter screen of the dryer cartridge

the journey Workshop findings: Refrigerant line between refrigerant compressor and condenser is cracked If listed line is cracked, please conduct the following tests 1. Are the fault codes B19A200 or P053400 current or stored in air conditioner control unit N10*1? 2. Check dryer cartridge at condenser for particles: Remove dryer cartridge, illuminate inlet of dryer cartridge using flashlight (A), and examine filter screen through outlet of dryer cartridge (B) -> see comparison picture bad/good Cause The refrigerant line between the A/C compressor and capacitor may be damaged due to a high refrigerant temperature. Remedy If the tests listed have been carried out and the results correspond to the described fault profile, please carry out the following steps: If the tests listed have been carried out and the results correspond to the described fault profile, please carry out the following steps: 1. Flushing of the refrigerant circuit as per AR83.30-P-1785EQA 2. Then replace the following parts: A/C compressor (***IMPORTANT: If the A/C compressor A0008304404 or A0008307704 is installed in the vehicle, it must be replaced by part number A0008307804***) If the capacitor A0998301100 is installed, then replace the complete capacitor (including dryer cartridge and PT sensor). If capacitor A0998301400/1500 is installed, only new dryer cartridge (A2938350500) Refrigerant line between refrigerant compressor and capacitor (A2438308600) 3. To use the new refrigerant line A2438308600, the electric line for pressure sensor B161/2 must be extended using the adapter wiring harness A2435408724. Disconnect plug from pT sensor Route the adapter line A2435408724 to the newly positioned pT sensor and secure it with a cable tie to prevent chafing 4. Insert the blind plug from the adapter wiring harness onto the old sensor. 5. Check SAM (N10) for latest software. If necessary, perform software update. 6. Finally, please check whether all heating and cooling functions are working; if not, please create a TIPS case with the following information: Detailed description of the customer complaint and the workshop measures carried out Initial quick test Photos of the filter screen of the dryer cartridge

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored in the same ignition cycle, additional warning messages, e.g. red HV warning message and yellow HV drive system warning message may be shown. The DC/DC converter has stored a combination of the following two fault code groups: 1. P0C3B00, P0E9700, P0E5400, P0C4000. 2. P1D0B00, P1CA000, U011500. In some cases, not all DTCs from one of these groups are triggered. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00 can be set. This triggers the yellow HV drive system warning message. In the ignition cycle in which the red 12 V fault message is displayed, the DC/DC converter does not support the 12 V on-board electrical system. This means the 12 V battery may be discharged in the event of longer use. Cause In individual ignition cycles, this may result in faulty wake-up behavior of the DC/DC converter. The DCDC DTCs and warning messages may appear with a time delay. When accessing the vehicle, the white (243/465) HV warning message is displayed. When the HV system is switched on (charging, 12V supports, precon, ignition on), the yellow HV drive system warning message is displayed on the 243 with BMS30EB02 (see below for details). When the vehicle is started/PT-ready (displayed in the IC), the red 12V battery warning message is displayed for 243 and 465. - This warning message indicates that the DC/DC was not properly initialized in the current cycle and the 12V on-board electrical system is not being supplied. Since the BMS on 243 uses the HV voltage value to check the auxiliary assembly fuse, the auxiliary assembly DTC can (with BMS30EB02) be stored as a consequence and the second (yellow) HV drive system warning message can be displayed in the IC. Remedy 243 EB330 (BMS30EB02): Update the DC/DC converter software to version A0019024327 + Erase fault memory. 465: Update the DC/DC converter software to version A0019024327 + Erase fault memory. !!! Important note: Problems relating to this topic must be invoiced on the damage code for the DC/DC converter 54720. !!

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 double-click on the locking button As of modification year 22/1, by pressing and holding the locking button + double-clicking on the release tab On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The fault message and the fault memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For plug-in Model Series167, 206, 214, 223, 247, 254: Carry out software update and SCN coding for the control unit "N83 AC charger for high-voltage battery (SG-LG)". For model series 243: Carry out software update and SCN coding for the control units "N116/5 DC charge-connection unit (DCCU)" and "N83/11 AC charger for high-voltage battery (SG-LG)"

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The fault message and the fault memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For the plug-in hybrid model series 118, 167, 206, 214, 223, 247, 254: Carry out software update and SCN coding for the control unit "N83 AC charger for high-voltage battery (SG-LG)". For model series 243: Carry out software update and SCN coding for the control units "N116/5 DC charge-connection unit (DCCU)" and "N83/11 AC charger for high-voltage battery (SG-LG)"

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The instrument cluster message and the FC memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 206 and 223 with code 802: Perform a software update and SCN coding for the control unit "N83/11 - AC charger for high-voltage battery (SGLG)" in order to remedy the problem. For model series 243: The correction is already available. Perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The instrument cluster message and the FC memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 206 and 223 with code 802: Perform SCN coding in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Please do not replace any parts even if the FC P0CFE00 coding continues to appear after successfully completing this step. A new software fix is currently in development and will likely be published in 01/2026. Replacing parts will not remedy the issue. For model series 243: The correction is already available. Perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The fault message and the fault memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 167, 214, 254 and 223 with code 802: Perform SCN coding in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Please do not replace any parts even if the FC P0CFE00 coding continues to appear after successfully completing this step. A new software is currently in development and will become available in late 01/2026. Replacing parts will not remedy the issue. For model series 243: The correction is already available. Please inform the workshop to perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

system The following fault codes related to interlock can be found in the High Voltage Control units : PTCU (N127) : P154700 - There is a warning due to a detected fault in the interlock circuit. BMS (N82/9) : P0A0B00 - The interlock circuit of the high-voltage on-board electrical system has a malfunction. P0A0D00 - The interlock circuit of the high-voltage on-board electrical system has a short circuit to positive. DCB (N116/5): P0A0A00 - The interlock circuit of the high-voltage on-board electrical system has an electrical fault. P0A0B00 - The interlock circuit of the high-voltage on-board electrical system has a malfunction. P0A0C00 - The interlock circuit of the high-voltage on-board electrical system has a short circuit to ground. OBL (N83/11) : P0A0B00 - The interlock circuit of the high-voltage on-board electrical system has a malfunction. P0A0C00 - The interlock circuit of the high-voltage on-board electrical system has a short circuit to ground. Instrument cluster warning messages : Cause Oxidation in interlock circuit pins of the low voltage connectors in the components Twisted harness Harness scratching with the body Wiring harness chafed/cut at the ECUs Broken interlock connector Improperly connected HV connectors Interlock pins on HV components are bent or deformed Important Note : In case of interlock failures, the High-voltage component is less likely to cause the issue. Remedy Remedy 1: Interlock loop resistance measurement (Refer attachment "243 Interlock Resistance Measurements.pdf") Remedy 2: Additional check points for interlock issues

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The fault message and the fault memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 167, 214, 254 and 223 with code 802: Perform SCN coding in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Please do not replace any parts even if the FC P0CFE00 coding continues to appear after successfully completing this step. A new software is currently in development and will become available in late 12/2025. Replacing parts will not remedy the issue. For model series 243: The correction is already available. Please inform the workshop to perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

system The following fault codes related to interlock can be found in the High Voltage Control units : PTCU (N127) : P154700 - There is a warning due to a detected fault in the interlock circuit. BMS (N82/9) : P0A0B00 - The interlock circuit of the high-voltage on-board electrical system has a malfunction. P0A0D00 - The interlock circuit of the high-voltage on-board electrical system has a short circuit to positive. DCB (N116/5): P0A0A00 - The interlock circuit of the high-voltage on-board electrical system has an electrical fault. P0A0B00 - The interlock circuit of the high-voltage on-board electrical system has a malfunction. P0A0C00 - The interlock circuit of the high-voltage on-board electrical system has a short circuit to ground. OBL (N83/11) : P0A0B00 - The interlock circuit of the high-voltage on-board electrical system has a malfunction. P0A0C00 - The interlock circuit of the high-voltage on-board electrical system has a short circuit to ground. Cause Oxidation in interlock circuit pins of the low voltage connectors in the components Twisted harness Harness scratching with the body Wiring harness chafed/cut at the ECUs Broken interlock connector Improperly connected HV connectors Interlock pins on HV components are bent or deformed Important Note : In case of interlock failures, the High-voltage component is less likely to cause the issue. Remedy Remedy 1: Interlock loop resistance measurement (Refer attachment "243 Interlock Resistance Measurements.pdf") Remedy 2: Additional check points for interlock issues

electrical system The following fault codes related to stuck contactor can be found in the High Voltage Control units : PTCU - N127 (Powertrain control unit) P154900 - There is a warning due to overcurrent in the charging system of the high-voltage electric circuit. P154A00 - There is a warning due to a detected crash event at standstill. P154B00 - There is a warning due to a stuck contactor. DCB223 - N116/5 (Direct current charge connection unit) P0E8929 - The input current of the on-board DC charging connection unit is too high. There is an invalid signal. P2BC500 - The contact ''Positive terminal'' of the contactor in the on-board DC current charge-connection unit is jammed closed P2BCC00 - The contact ''Negative terminal'' of the contactor in the on-board DC current charge-connection unit is jammed closed. Cause Current ripple due to EVSE (Electric Vehicle Supply Equipment) Overcurrent or Overvoltage due to EVSE (Electric Vehicle Supply Equipment) DCB contactors did not open immediately due to welding time at the end of DC charging Remedy Check for a new software availability for DCCU (N116/5 - Direct Current Charge connection Unit). If a new software is available, update the software first. Reset contactor fault through special procedure without password. ( N116/5 >> Special Procedure >> Resetting of contactor fault.) Important Note : Do not replace component DCB (N116/5) If fault codes are not erasable, please raise a TIPS case and send it to HQ.

the journey Workshop findings: Refrigerant line between refrigerant compressor and condenser is cracked If listed line is cracked, please conduct the following tests 1. Are the fault codes B19A200 or P053400 current or stored in air conditioner control unit N10*1? 2.Check dryer cartridge at condenser for particles: Remove dryer cartridge, illuminate inlet of dryer cartridge using flashlight (A), and examine filter screen through outlet of dryer cartridge (B) -> see comparison picture bad/good Further possible signs for this fault profile are: Refrigerant level clearly too low (target: 670 g): In this case, please first of all check where a leak is present in the system Loud noises from compressor: If loud noises are coming from the compressor, this finding must be validated with the two tests specified above (check the dryer cartridges or the specified fault codes). Loud noises alone are no reason to replace the compressor, since these can be very subjectively perceived in individual cases. Cause The refrigerant line between the A/C compressor and capacitor may be damaged due to a high refrigerant temperature. Remedy If the tests listed have been carried out and the results correspond to the described fault profile, please carry out the following steps: 1. Flushing of the refrigerant circuit as per AR83.30-P-1785EQA 2. Then replace the following parts: A/C compressor (***IMPORTANT: If the A/C compressor A0008304404 or A0008307704 is installed in the vehicle, it must be replaced by part number A0008307804***) Refrigerant line between refrigerant compressor and condenser If the capacitor A0998301100 is installed, then replace the complete capacitor (including dryer cartridge and PT sensor). If capacitor A0998301400/1500 is installed, only new dryer cartridge (A2938350500) 33. In order to use the new refrigerant line A2438308600, the electrical wire of pressure sensor B161/2 must be extended. Disconnect plug from pT sensor. Remove insulation approx. 15 cm from the plug. Extend lines by 425 mm. For this purpose, please observe the Basic data for wiring harness repairs with axial solder connectors (AR54.18-P-0100-06A). Wrap wiring harness with complete insulation wrapping. Route wire to the newly positioned pT sensor and secure with cable tie to prevent scouring. 4. Install 4 blind plugs (4x A0005458780) in coupling housing A0285458362 and fit it onto the old sensor. 5. Check SAM (N10) for latest software. If necessary, perform software update. 6. Please then check whether all of the heating and cooling functions are active. If not, please create a TIPS case with the following information: Detailed description of the customer complaint and the workshop measures carried out Initial quick test Photos of the filter screen of the dryer cartridge

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: vehicle technical issue? customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: Amperage setting of charger and time battery was on charger XENTRY Battery Tester results Voltage of battery taken with multimeter: Do not connect charger while taking measurements N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) Workshop analysis of conspicuous data Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The fault message and the fault memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 167, 214, 254 and 223 with code 802: Perform SCN coding in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Please do not replace any parts even if the FC P0CFE00 coding continues to appear after successfully completing this step. A new software is currently in development and will become available in 11/2025. Replacing parts will not remedy the issue. For model series 243: The correction is already available. Please inform the workshop to perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Initial problem - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] - Delete fault memory and recheck vehicle Note - If wiring fault is found in newer vehicle, please send in a IFQ (Initial Field Quality) TIPS Case. 2. Subsequent problem after repair In this case, the workshop must perform the following operation steps: - Replace overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) - Clean electrical connectors of overhead control panel with commercially available contact cleaner and clean, purified compressed air. - Delete fault memory and recheck vehicle Note - If no remedy is found, please open a TIPS case and send to the Body/Chassis/Entertainment inbox.

In such cases, "Playback not active" is shown in the display. Cause Mute line between communication module N112/2 and sound control unit N40/3. Remedy Check the mute cable between control units N112/2 (communication module) and N40/3 (sound system). Inspect the cable and plug contacts for damage or deformation. Repair or replace the cable as needed. Important: If any plug contact is found to be deformed, you must also inspect the corresponding connector on the control unit to ensure it is not compromised.

Cause There are several reasons for the activation of the Reduced Drive Power Warning, Here are a few examples: Hood is not closed properly Valet Service Mode is activated Beginner Driver Mode is activated Remedy If no relevant fault codes are present, first ensure the hood is securely closed and verify that neither Valet Service Mode nor Beginner Driver Mode is activated in MBUX. If relevant fault codes are detected, then proceed with diagnosing and resolving those specific faults.

the journey Workshop findings: Refrigerant line between refrigerant compressor and condenser is cracked If listed line is cracked, please conduct the following tests 1. Are the fault codes B19A200 or P053400 current or stored in air conditioner control unit N10*1? 2. Check dryer cartridge at condenser for particles: Remove dryer cartridge, illuminate inlet of dryer cartridge using flashlight (A), and examine filter screen through outlet of dryer cartridge (B) -> see comparison picture bad/good Further possible signs for this fault profile are: Refrigerant level clearly too low (target: 670 g): In this case, please first of all check where a leak is present in the system Loud noises from compressor: If loud noises are coming from the compressor, this finding must be validated with the two tests specified above (check the dryer cartridges or the specified fault codes). Loud noises alone are no reason to replace the compressor, since these can be very subjectively perceived in individual cases. Cause The refrigerant line between the A/C compressor and capacitor may be damaged due to a high refrigerant temperature. Remedy If the tests listed have been carried out and the results correspond to the described fault profile, please carry out the following steps: 1. Flushing of the refrigerant circuit as per AR83.30-P-1785EQA 2. Then replace the following parts: A/C compressor (***IMPORTANT: If the A/C compressor A0008304404 or A0008307704 is installed in the vehicle, it must be replaced by part number A0008307804***) Refrigerant line between refrigerant compressor and condenser If the capacitor A0998301100 is installed, then replace the complete capacitor (including dryer cartridge and PT sensor). If capacitor A0998301400/1500 is installed, only new dryer cartridge (A2938350500) 3. Check SAM (N10) for latest software. If necessary, perform software update. 4. Please then check whether all of the heating and cooling functions are active. If not, please create a TIPS case with the following information: Detailed description of the customer complaint and the workshop measures carried out Initial quick test Photos of the filter screen of the dryer cartridge

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: vehicle technical issue? customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge, create a TIPS case. -Must include with the case: Amperage setting of charger and time battery was on charger XENTRY Battery Tester results Voltage of battery taken with multimeter: Do not connect charger while taking measurements N10/6 FSAM and N73/3 EZS CUL Workshop analysis of conspicuous data Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Test: Please perform the new SCN coding for HOSWD control unit (N179/1) (available since May 2025). Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> Please create TIPS case! If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no fault is visible: Please open a TIPS case! In the event of a customer complaint and further fault code in HOSWD: B1E7713: Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). B1F1F04: Check hand detection system control unit; if necessary swap with donor vehicle (ensure that the HW part numbers are identical).

stored in the "N83 - AC charger for high-voltage battery (SG-LG)" control unit. The fault message and the fault memory entry can also appear during time-delayed charging at the start of the pause in charging. Both only occur in combination with active pre-entry climate control. Cause Software in the "N83 - AC charger for high-voltage battery (SG-LG)" control unit. Remedy For 206 and 223 model lines with code 802 - Perform SCN coding in control unit "N83 - AC charger for high-voltage battery (SG-LG)". If, even after the coding has been successfully completed, the FC P0CFE00 continues to occur, please do not replace any parts. New software fix is currently in development and it is expected to be released by 08/2025. Replacing of parts will not bring in any remedial action. For 243 model line - Fix is already available. Please tell the workshop to perform software update and SCN coding for control units "N116/5 - Direct current charge connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" to resolve the problem.

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Test: Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Reset the HOSWD control unit in line with the guided test in Xentry. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> replace steering wheel rim. If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no defect is visible: Please do not replace the steering wheel, but wait for new coding parameters which should be available 05/2025. Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. B1E7713: Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is now available for Star 3 vehicles only. Fault in IDC223 control unit: U186B29: Delete fault memory and flash the new IDC (N62/4) software A223 902 75 37. If the software update is not available, or the problem persists, create a TIPS case. Fault in IDC213 control unit: U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the HOSWD control unit then scan the steering wheel and check whether the fault is reproducible. If reproducible: Create a TIPS case, adding the

Cause Temperature sensor in overhead control panel (OCP) delivering incorrect values: The temperature sensor in the overhead control panel is malfunctioning. Fault code B110709 or fault code B11F697 are present in the overhead control panel with the status (active) or (active stored). or The temperature sensor in the overhead control panel measures an incorrect temperature (the temperature value can be checked against the actual value in the overhead control panel) If the above-mentioned fault code is not present, the cause could be malfunction on the air conditioning system. Remedy If one of the above-mentioned fault codes should occur, a TIPS case must be created here. If the above fault codes or actual value differences are present in the OCP - please send the case to the Body/Chassis/ Entertainment inbox. Otherwise, the case must be sent to the HV/LV inbox for support in A/C diagnosis. *** It is not necessary to replace the overhead control panel ***

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Enter AO Code O19 into VeDoc (O for Oscar, not "zero") 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 double-click on the locking button As of modification year 22/1, by pressing and holding the locking button + double-clicking on the release tab On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. B1E7713: Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is now available for Star 3 vehicles only. Fault in IDC223 control unit: U186B29: Delete fault memory and flash the new IDC (N62/4) software A223 902 75 37. If the software update is not available, or the problem persists, create a TIPS case. Fault in IDC213 control unit: U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the HOSWD control unit then scan the steering wheel and check whether the fault is reproducible. If reproducible: Create a TIPS case, adding the note "reproducible". If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. New coding parameters (SCN) will be available in Q2/2025 for the HOSWD control unit.

If you have symptoms with one or both displays, a TIPS case must be created. The TIPS case will be reviewed by MBUSA and GCSP. NOTE: Please perform the following steps before creating a TIPS case: Step 1: Check software release of the following control units to see if they are up to date; if necessary perform software update. Instrument cluster (IC177 / IC 177M) Head unit (HU6 / HU7) All displays (DISP6 / DISP7S2) Reassess for the symptom. If the symptom is still present, continue with step 2. Step 2: Perform swap (swap display with a display from a reference vehicle) and reassess for the symptom. If the problem relates to the display, replace display. If the problem does not relate to the display, continue with step 3. Step 3: Check electrical wiring harness and video line (LVDS) for routing and external damage. Check contact pins and contact sockets for corrosion and bonding (photo documentation in micro view format requested). Check electric wiring harness for conductivity and short circuit, document measurement results in a measurement report or referenced wiring diagram using the CDT four level model. If the wiring harness and the video line is OK, please complete the attached questionnaire, create TIPS case according to list of requirements. Please add the following documents to the TIPS case: Video of problem Completed questionnaire Current quick test with freeze frame results Measurement report and photo documentation of wiring harness Control unit log of head unit Control unit log of instrument cluster Control unit log of display cluster Log-files HU-logging (password via TIPS case) NOTE: Make sure to document the original customer complaint. NOTE: Please refer to this LI in the warranty claim in the "Notes" section. The damage code of the component determined to be the root cause of the symptom must be used in the warranty claim.

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. B1E7713: Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is now available for Star 3 vehicles only. Fault in IDC223 control unit: U186B29: Delete fault memory and flash the new IDC (N62/4) software A223 902 75 37. If the software update is not available, or the problem persists, create a TIPS case.

If you have symptoms with one or both displays, a TIPS case must be created. The TIPS case will be reviewed by MBUSA and GCSP. NOTE: Please perform the following steps before creating a TIPS case: Step 1: Check software release of the following control units to see if they are up to date; if necessary perform software update. Instrument cluster (IC177 / IC 177M) Head unit (HU6 / HU7) All displays (DISP6 / DISP7S2) Reassess problem. If the problem is still present, continue with step 2. Step 2: Perform swap (swap display with a display from a reference vehicle) and reassess problem. If the problem relates to the display, replace display. If the problem does not relate to the display, continue with step 3. Step 3: Check electrical wiring harness and video line for routing, breakovers and external damage. Check contact springs and contact sockets for corrosion and bonding (photo documentation in micro view). Check electric wiring harness for conductivity and short circuit, document measurement results in a measurement report or referenced wiring diagram using the CDT four level model. If the wiring harness and the video line is OK, please complete the attached questionnaire, create TIPS case according to list of requirements. Please add the following documents to the TIPS case: Video of problem Completed questionnaire Current quick test with freeze frame results Measurement report and photo documentation of wiring harness Control unit log of head unit Control unit log of instrument cluster Control unit log of display cluster Log-files HU-logging (password via TIPS case) NOTE: Make sure to document the original customer complaint. NOTE: Please refer to this LI in the warranty claim in the "Notes" section. The damage code of the component determined to be the root cause of the symptom must be used in the warranty claim.

and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 01.06.2023 (Send to Body/Chassis/Entertainment Inbox) - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 01.06.2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.

and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.

Charging bar stops at 0%. (Picture in attachment) Cause Communication between light control unit and HU Remedy Software update to latest version: - A26/17 - MBUX multimedia system (head unit) - E1n14 - Front left digital headlamp control unit (DHLS-CU-VL) - E2n14 - Front right digital headlamp control unit (DHLS-CU-VR)

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.

Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button

Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

the software for the DC charge-connection unit (DCCU) control unit does not correspond to current production specifications. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update software of DCCU control unit. This software update will enable compatibility with Plug & Charge functionality on the Tesla Supercharger network.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

voltage battery state of charge (SOC) is >80% Recouperation settings active (Intelligent, D-, or D) Cause The high voltage battery cannot achieve full recouperation from the electric motor due to the already high battery state of charge and is supported via the hydraulic portion of the brakes. The sound is from the hydraulic portion of the braking system. Remedy The noise is normal, no parts need to be replaced and no further action required.

vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored in the same ignition cycle, additional warning messages, e.g. red HV warning message and yellow HV drive system warning message may be shown. The DC/DC converter has stored a combination of the following two fault code groups: 1. P0C3B00, P0E9700, P0E5400, P0C4000. 2. P1D0B00, P1CA000, U011500. In some cases, not all DTCs from one of these groups are triggered. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00 can be set. This triggers the yellow HV drive system warning message. In the ignition cycle in which the red 12 V fault message is displayed, the DC/DC converter does not support the 12 V on-board electrical system. This means the 12 V battery may be discharged in the event of longer use. Cause In individual ignition cycles, this may result in faulty wake-up behavior of the DC/DC converter. The DCDC DTCs and warning messages may appear with a time delay. When accessing the vehicle, the white (243/465) HV warning message is displayed. When the HV system is switched on (charging, 12V supports, precon, ignition on), the yellow HV drive system warning message is displayed on the 243 with BMS30EB02 (see below for details). When the vehicle is started/PT-ready (displayed in the IC), the red 12V battery warning message is displayed for 243 and 465. - This warning message indicates that the DC/DC was not properly initialized in the current cycle and the 12V on-board electrical system is not being supplied. Since the BMS on 243 uses the HV voltage value to check the auxiliary assembly fuse, the auxiliary assembly DTC can (with BMS30EB02) be stored as a consequence and the second (yellow) HV drive system warning message can be displayed in the IC. Remedy 243 EB330 (BMS30EB02): Update the DC/DC converter software to version A0019024327 465: Perform reset of the DC/DC converter, e.g. through a BUS idle or by clearing the fault memory, to exit the faulty state. Update the DC/DC converter software to the latest version. !!! Important note: Problems relating to this topic must be invoiced on the damage code for the DC/DC converter 54720. !!!

vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored in the same ignition cycle, additional warning messages, e.g. red HV warning message and yellow HV drive system warning message may be shown. The DC/DC converter has stored a combination of the following two fault code groups: 1. P0C3B00, P0E9700, P0E5400, P0C4000. 2. P1D0B00, P1CA000, U011500. In some cases, not all DTCs from one of these groups are triggered. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00 can be set. This triggers the yellow HV drive system warning message. In the ignition cycle in which the red 12 V fault message is displayed, the DC/DC converter does not support the 12 V on-board electrical system. This means the 12 V battery may be discharged in the event of longer use. Cause In individual ignition cycles, this may result in faulty wake-up behavior of the DC/DC converter. The DCDC DTCs and warning messages may appear with a time delay. When accessing the vehicle, the white (243/465) HV warning message is displayed. When the HV system is switched on (charging, 12V supports, precon, ignition on), the yellow HV drive system warning message is displayed on the 243 with BMS30EB02 (see below for details). When the vehicle is started/PT-ready (displayed in the IC), the red 12V battery warning message is displayed for 243 and 465. Since the BMS on 243 uses the HV voltage value to check the auxiliary assembly fuse, the auxiliary assembly DTC can (with BMS30EB02) be stored as a consequence and the second (yellow) HV drive system warning message can be displayed in the IC. Remedy The faulty state of the DC/DC converter can always be rectified with an ignition change with BUS idle. The fact that the red 12 V warning message does not appear again is an indication of this. On vehicles with the yellow hybrid drive system message, it is still displayed because it is not automatically reset once the faulty state is reset. Check the DC/DC converter for functionality via Xentry Diagnostics in the workshop: Actuate BUCK mode for approx. 30 s The output current normally jumps to a high value (e.g. 100 A) and then falls slowly to the current specified value e.g. 50 A and then only changes slowly and in small increments. 243 EB311/312 (BMS30EB01): Perform reset of the DC/DC converter, e.g. through a BUS idle or by clearing the fault memory, to exit the faulty state. 243 EB330 (BMS30EB02): Clear the fault memory, since the DTC for the auxiliary assembly fuse and the yellow hybrid drive system warning message are not automatically reset. 465: Perform reset of the DC/DC converter, e.g. through a BUS idle or by clearing the fault memory, to exit the faulty state. !!! Important note: Problems in this area do not have to be invoiced on the damage code for the DC/DC converter 54720. !!! Information: Cause analysis is still ongoing in order to determine a long-term remedy. In cases in which the fault profile occurs multiple times, replacement of the DC/DC converter can be carried out. This may help delay the fault profile from reoccurring.

12V battery (red) Different combinations of the following DTCs present in the ESP: B23AA77, B23AB77, B23D177 and in part (C100BE0, C100BE1, B23AA1B, B23D152) Cause Due to a reduction in resistance at the HV voltage divider, the DC/DC converter measures an incorrect HV voltage. Regulation of the 12 V output voltage therefore becomes unstable. I.e. the output voltage starts to fluctuate and the output current starts to jump instead of slowly regulating to the currently requested value. The EPB position is calculated by the voltage and the current. Since these fluctuate, the ESP control unit loses its position and sets the DTCs. Remedy Check of the DC/DC converter via XENTRY Diagnosis Actuate BUCK mode for approx. 40 s The output current normally jumps to a high value (e.g. 100 A) and then falls slowly to the current specified value e.g. 50 A and then only changes slowly and in small increments. In the event of this fault cause, the output current is subject to strong fluctuations/jumps (multiple 1-10 A) (see videos in attachment) Perform in XENTRY -> DC/DC converter N83/1 -> Special procedures -> "Evaluation of the HV resistance reduction of the DC/DC converter control unit". The special procedure compares the serial number of the installed DC/DC converter with the list of potentially affected parts. Depending on the result: If the serial number can be found in the list of potentially affected component parts, then replace the DC/DC converter. If the serial number cannot be found in the list of potentially affected parts, XENTRY reports that the part is not malfunction. If the problem from this LI applies, please open a TIPS case and forward to HQ. Subsequent complaint, malfunction on the EPB: Check of the actuators and brake caliper piston Manually extend and retract the piston on the brake caliper completely using the suitable socket If the piston sticks at a certain point, the rotation force increases significantly If the brake caliper piston sticks, the brake caliper has to be replaced If the retaining ring of the actuator is broken, the actuator has to be replaced In XENTRY, edit the stored test instructions of the remaining DTCs

vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored, additional further warning messages (e.g. red HV warning message and yellow HV drive system warning message) are displayed. The DC/DC converter has saved the four following fault codes at most: P0C3B00, P0E9700, P0E5400, P0C4000. In some cases, not all of these DTCs are triggered. The following DTCs either be triggered additionally or, in rare cases, without the previous DTCs: P1D0B00, P1CA000, U011500. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00 can be set. That triggers the yellow HV drive system warning message. Cause: This may result in incorrect wake-up behavior of the DC/DC converter. The DCDC DTCs and warning messages may appear with a time delay. When accessing the vehicle, the white (243/465) HV warning message is displayed. When the HV system is switched on (charging, 12V supports, precon, ignition on), the yellow HV drive system warning message is displayed on the 243 with BMS30EB02 (see below for details). When the vehicle is started/PT-ready (displayed in the IC), the red 12V battery warning message is displayed for 243 and 465. Since the BMS on 243 uses the HV voltage value to check the auxiliary assembly fuse, the auxiliary assembly DTC can (with BMS30EB02) be stored and the second (yellow) HV drive system warning message can be displayed in the IC. Remedy: Check of the DC/DC converter via XENTRY Diagnosis Actuate BUCK mode for approx. 30 s The output current normally jumps to a high value (e.g. 100 A) and then falls slowly to the current specified value e.g. 50 A and then only changes slowly and in small increments. 243 EB330 (BMS30EB02): Clear the fault memory, since the DTC for the auxiliary assembly fuse and the yellow hybrid drive system warning message can only be reset in this way. 465: Perform a reset of the DC/DC converter, e.g. through a BUS idle or by clearing the fault memory, to exit the error state. Information: Cause analysis is still ongoing in order to determine a long-term remedy. In cases in which the fault profile occurs multiple times, please open a TIPS case.

vehicles with BMS30EB02 yellow HV drive system 465: Red 12V battery message, white HV warning message, warning message in the IC If the initial warning messages are ignored, additional further warning messages (e.g. red HV warning message and yellow HV drive system warning message) are displayed. The DC/DC converter has saved the four following fault codes at most: P0C3B00, P0E9700, P0E5400, P0C4000. In some cases, not all of these DTCs are triggered. The following DTCs either be triggered additionally or, in rare cases, without the previous DTCs: P1D0B00, P1CA000, U011500. 243: As a consequence, on vehicles with BMS30EB02, the DTC for the auxiliary assembly fuse P0E2F00 can be set. That triggers the yellow HV drive system warning message. Cause: This may result in incorrect wake-up behavior of the DC/DC converter. The DCDC DTCs and warning messages may appear with a time delay. When accessing the vehicle, the white (243/465) HV warning message is displayed. When the HV system is switched on (charging, 12V supports, precon, ignition on), the yellow HV drive system warning message is displayed on the 243 with BMS30EB02 (see below for details). When the vehicle is started/PT-ready (displayed in the IC), the red 12V battery warning message is displayed for 243 and 465. Since the BMS on 243 uses the HV voltage value to check the auxiliary assembly fuse, the auxiliary assembly DTC can (with BMS30EB02) be stored and the second (yellow) HV drive system warning message can be displayed in the IC. Remedy: Check of the DC/DC converter via XENTRY Diagnosis Actuate BUCK mode for approx. 30 s The output current normally jumps to a high value (e.g. 100 A) and then falls slowly to the current specified value e.g. 50 A and then only changes slowly and in small increments. 243 EB330 (BMS30EB02):Clear the fault memory, since the DTC for the auxiliary assembly fuse and the yellow hybrid drive system warning message can only be reset in this way. 465:Perform a reset of the DC/DC converter, e.g. through a BUS idle or by clearing the fault memory, to exit the error state. Information: Cause analysis is still ongoing in order to determine a long-term remedy. In cases in which the fault profile occurs multiple times, please open a TIPS case.

Cause The lower connection of the shock absorber (damper) to the lower transverse control arm might not have been torqued to specification. Remedy Tighten threaded connection to listed appropriate torque. (See WIS). Replacing the shock absorber (damper) does not remedy the problem. Invoice SSL 32D07 and 32S07 for this. Note: The threaded connection is self-locking and will not detach. Noise is the only byproduct.

12 V battery (red) Different combinations of the following DTCs present in the ESP: B23AA77, B23AB77, B23D177 and in part (C100BE0, C100BE1, B23AA1B, B23D152) Cause Due to a reduction in resistance at the HV voltage divider, the DC/DC converter measures an incorrect HV voltage. Regulation of the 12 V output voltage therefore becomes unstable. I.e. the output voltage starts to fluctuate and the output current starts to jump instead of slowly regulating to the currently requested value. The EPB position is calculated by the voltage and the current. Since these fluctuate, the ESP control unit loses its position and sets the DTCs. Remedy Check of the DC/DC converter via XENTRY Diagnosis: Compare the serial number of the DC/DC converter with a list of potentially affected parts in XENTRY -> DC/DC converter N83/1 -> Special Processes. If the evaluation comes back as defective - Replace the DC/DC converter and inspect the EPB for Subsequent complaint, defect. If the evaluation comes comes back not affected: Actuate BUCK mode for approx. 30 s The output current normally jumps to a high value (e.g. 100 A) and then falls slowly to the current specified value e.g. 50 A and then only changes slowly and in small increments. In the event of this fault cause, the output current is subject to strong fluctuations/jumps (multiple 1-10 A) (see videos in attachment). In the event of strong fluctuations and the S/N not identified in the Special Process, please open a TIPS case and attach print out of DC/DC special procedure and buck mode actual values. Subsequent complaint, defect on the EPB: Check of the actuators and brake caliper piston Manually extend and retract the piston on the brake caliper completely using the suitable socket If the piston sticks at a certain point, the rotation force increases significantly If the brake caliper piston sticks, the brake caliper has to be replaced If the retaining ring of the actuator is broken, the actuator has to be replaced In XENTRY, edit the stored test instructions of the remaining DTCs

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

Fault code P25567B ('Coolant level' sensor has detected a fault, fluid level is too low.) is stored in the signal acquisition and actuation module (SAM) control unit N10. Cause The vehicle's electric drive motor transports air into the cooling system. The air transported into the cooling system leads to the formation of an air cushion in the expansion reservoir, which in turn causes the coolant level to drop below the warning threshold of the coolant's fill level sensor when driving. After opening the closing cap, the coolant level is OK again. Remedy Replace the black cap A210 501 06 15 of the large working chamber of the expansion reservoir with a red cap A297 500 51 00 and the coolant level rises by roughly 20 mm above the MAX. marking. On vehicles in which the problem cannot be rectified by this procedure, the expansion reservoir A 243 500 41 00 is replaced by the modified container A243 500 60 00. The new expansion reservoir is to have two red closing caps A 297 500 51 00 fitted to it, and the coolant level is to be set to the MAX. marking.

purchased at an authorized Mercedes-Benz Dealer. During your visit, an authorized Mercedes-Benz dealer will install a NACS adapter information label on your vehicles charging flap, free of charge.

Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

Fault code P25567B (The 'Coolant level' sensor has a malfunction. The fluid level is too low) is stored in the signal acquisition and actuation module (SAM) control unit N10. Cause The electric drive motor of the vehicle conveys air into the cooling system. The air conveyed into the cooling system leads to an air cushion forming in the expansion reservoir, which in turn causes the coolant level to fall below the warning threshold of the coolant level sensor during travel. After the cap is opened, the coolant level is once again OK. Remedy Replace the black cap A210 501 06 15 of the large working chamber of the expansion reservoir with a red cap A297 500 51 00 and increase the coolant level by 20 mm over the max. marking. On vehicles where this process does not remedy the issue, the expansion reservoir A 243 500 41 00 is replaced by the modified container A243 500 41 00 28. If the problem is still present, please create a TIPS case.

Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

GLC vehicles (243, 247, and 254 platform), the B-pillar certification label might not contain the vehicles rim size, tire size, and cold tire inflation pressure information as required by FMVSS 110. In this case, relevant regulatory requirements might not be met. Mercedes-Benz believes this issue has no impact on vehicle safety. Mercedes-Benz intends to submit a petition to NHTSA for exemption from the notification and remedy requirements of 49 U.S.C. chapter 301, pursuant to 49 CFR Part 556, on the basis that this noncompliance is inconsequential as it relates to motor vehicle safety.

Cause Leaves/foreign objects have entered through the water drain grille in the water drain thereby causing an imbalance and noise in the blower wheel. Remedy Instructions for the installation of Retrofit Kit TOP598-MFA2 Bermuda foam for model series X243/X247 A2478351400 Sealing frame A2478351500 Sealing frame A2478351600 Sealing frame A2478351700 Sealing frame A2478351800 Sealing frame A2478351900 Sealing frame A2478300104 Housing cover A2478320200 Drainage fitting Steps: 1- Remove windshield wiper as per work instructions: AR82.30-P-6100MFA 2- Remove water baffle cover as per work instructions:AR83.10-P-1411MFB 3- Thoroughly clean body/body-in-white at marked positions and remove plastic cover to air inlet. Then extract air filter. 4- Attach body-in-white foam A2478351600 to cutout at body-in-white. If necessary, fix part in place with light pressure. 5- Attach foam mat A2478351400 to previously cleaned part of body-in-white. Ensure that hole of foam mat is over the hole in the body-in-white. 6- Attach sealing frame A2478351800 along edge as shown in picture. Ensure that the plastic strip is inserted flush with the offset in the previously attached foam mat. 7- Attach sealing frame A2478351700 as shown in the picture. Take care here as the strip should be attached flush to the foam strip positioned lengthwise and must run vertically on the body-in-white downward in the direction of the seam. 8- Attach sealing frame A2478351900 as shown in the picture. Ensure that the foam strip must run along the seam and must be curved outward along the running direction at the end. (As a guide, the curvature should run so that there is a space of approx. 1 cm between the foam strip and the threaded hole). Alternatively, if the corresponding foam in the right picture is present, place the sealing frame A2478351900 along the foam as shown in the picture. 9- Insert drainage fitting A2478320200. When doing so, ensure that the foam flap is aligned in the direction of the fender as shown in the picture and does not fold upward during insertion. Insert fitting with light pressure until it audibly engages. 10- Attach sealing frame A2478351500 to water baffle as in the picture and insert inlet sieve A2478300104 (see picture). 11- Insert water baffle. When doing so, ensure that sealing frame A2478351600 does not fall out of position. Also ensure that the foam frames A2478351700, A2478351800 and A2478351900 run between the body-in-white and the water baffle (see picture). 12 - Clean out the water drains of any debris and ensure proper water flow away from the blower area. 13- Reinstallation of water baffle and windshield wiper (see step 1).

platform), EQB (243 platform), GLA (247 platform), EQE (294 platform), EQS (296 platform), and GLC (254 platform) vehicles, the B-pillar certification label might not contain the vehicles rim size, tire size, and cold tire inflation pressure information as required by FMVSS 110. In this case, relevant regulatory requirements might not be met. Mercedes-Benz believes this issue has no impact on vehicle safety. Mercedes-Benz intends to submit a petition to NHTSA for exemption from the notification and remedy requirements of 49 U.S.C. chapter 301, pursuant to 49 CFR Part 556, on the basis that this noncompliance is inconsequential as it relates to motor vehicle safety. MBUSA will conduct a service campaign to remedy new vehicles in dealer inventory. An authorized Mercedes-Benz dealer will replace the certification label on the B-Pillar.

platform), EQB (243 platform), GLA (247 platform), EQE (294 platform), EQS (296 platform), and GLC (254 platform) vehicles, the B-pillar certification label might not contain the vehicles rim size, tire size, and cold tire inflation pressure information as required by FMVSS 110. In this case, relevant regulatory requirements might not be met. Mercedes-Benz believes this issue has no impact on vehicle safety. Mercedes-Benz intends to submit a petition to NHTSA for exemption from the notification and remedy requirements of 49 U.S.C. chapter 301, pursuant to 49 CFR Part 556, on the basis that this noncompliance is inconsequential as it relates to motor vehicle safety. MBUSA will conduct a service campaign to remedy new vehicles in dealer inventory. An authorized Mercedes-Benz dealer will replace the certification label on the B-Pillar.

platform), EQB (243 platform), GLA (247 platform), EQE (294 platform), EQS (296 platform), and GLC (254 platform) vehicles, the B-pillar certification label might not contain the vehicles rim size, tire size, and cold tire inflation pressure information as required by FMVSS 110. In this case, relevant regulatory requirements might not be met. Mercedes-Benz believes this issue has no impact on vehicle safety. Mercedes-Benz intends to submit a petition to NHTSA for exemption from the notification and remedy requirements of 49 U.S.C. chapter 301, pursuant to 49 CFR Part 556, on the basis that this noncompliance is inconsequential as it relates to motor vehicle safety. MBUSA will conduct a service campaign to remedy new vehicles in dealer inventory. An authorized Mercedes-Benz dealer will replace the certification label on the B-Pillar.

platform), EQB (243 platform), GLA (247 platform), EQE (294 platform), EQS (296 platform), and GLC (254 platform) vehicles, the B-pillar certification label might not contain the vehicles rim size, tire size, and cold tire inflation pressure information as required by FMVSS 110. In this case, relevant regulatory requirements might not be met. Mercedes-Benz believes this issue has no impact on vehicle safety. Mercedes-Benz intends to submit a petition to NHTSA for exemption from the notification and remedy requirements of 49 U.S.C. chapter 301, pursuant to 49 CFR Part 556, on the basis that this noncompliance is inconsequential as it relates to motor vehicle safety. MBUSA will conduct a service campaign to remedy new vehicles in dealer inventory. An authorized Mercedes-Benz dealer will replace the certification label on the B-Pillar.

platform), EQB (243 platform), GLA (247 platform), EQE (294 platform), EQS (296 platform), and GLC (254 platform) vehicles, the B-pillar certification label might not contain the vehicles rim size, tire size, and cold tire inflation pressure information as required by FMVSS 110. In this case, relevant regulatory requirements might not be met. Mercedes-Benz believes this issue has no impact on vehicle safety. Mercedes-Benz intends to submit a petition to NHTSA for exemption from the notification and remedy requirements of 49 U.S.C. chapter 301, pursuant to 49 CFR Part 556, on the basis that this noncompliance is inconsequential as it relates to motor vehicle safety. MBUSA will conduct a service campaign to remedy new vehicles in dealer inventory. An authorized Mercedes-Benz dealer will replace the certification label on the B-Pillar.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10P067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. Please update the Head unit software to E505.9

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Head unit software variant. Remedy For all chassis use Xentry to update head unit (A26/17). Target boot software number should be either: 247 904 6600 (E905.4) OR 247 904 7500 (E906.1) If vehicle fits all criteria and either target software is not available via Xentry, please open an XSS ticket. Damage code 5424x-01 may be used with a repair start date after June 2nd, 2025.

multifunction display of the instrument cluster while driving (see picture in attachment). Cause For vehicles with HERMES 3.0, A2389015700 A2389015800 A2389018400 A2389018900 A2389019000 A2389019800 A2579011200 A2579012100 the above-mentioned message is sporadically displayed in the instrument cluster once the over-the-air update to software release E843 (Software part number A2389022409) has been performed. The coding was performed incompletely here. Remedy A relevant over-the-air software update campaign for the control unit N112/9 (HERMES) is in preparation. If the vehicle is already on site, the problem can be rectified by manually commissioning the control unit N112/9 (HERMES) with XENTRY: XENTRY. "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Head unit software variant. Remedy For all chassis use Xentry to update head unit (A26/17). Target boot software number should be either: 247 904 6600 (E905.4) OR 247 904 7500 (E906.1) If vehicle fits all criteria and either target software is not available via Xentry, please open an XSS ticket.

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Under analysis. Remedy For chassis 118, 167, 177, 213, 238, 243, 247, 253, and 293 use Xentry to update headunit (A26/17). Target software number is 247 904 6600 (E905.4). If vehicle fits all criteria and target software is not available via Xentry, please open an XSS ticket.

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Under analysis. Remedy For chassis 118, 167, 177, 213, 238, 243, 247, 253, and 293 use Xentry to update headunit (A26/17). Target software number is 247 904 6600 (E905.4).

AMG GT, EQE, EQS, G-CLASS, GLB, GLC, GLE, GLS, S-CLASS, AMG SL (206, 118, 243, 290, 192, 294, 295, 296, 297, 465, 247, 254, 167, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

vehicles, the BMS software does not correspond with current production specifications. In this case, a yellow malfunction warning message could erroneously be triggered and displayed in the instrument cluster. This warning message presents no impact to the functionality of the vehicle. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the software of the BMS control unit.

the vehicle is displayed as being in the middle of the ocean. Note: In the quick test, no relevant DTC is displayed for this. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the connector into the GNSS connection and ensure that the connector has engaged correctly and is fully seated.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.

The affected vehicles will be removed from display in VMI on June 12, 2024. Campaign will be deactivated since the remedy is still under analysis.

2024-2025 CLA, EQB, GLA, GLB, GLE, GLS, and AMG GT 4-door (118, 243, 247, 167, and 290 platform). The vehicles will be visible and flagged in VMI as OPEN on February 23, 2024. Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2024-2025 CLA, EQB, GLA, GLB, GLE, GLS, and AMG GT 4-door (118, 243, 247, 167, and 290 platform) vehicles, the MBUX control unit software might not correspond to current production specifications which may result in the radio being inoperative. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the MBUX Control Unit software.

TIREFIT sealant bottle may not meet specifications. The possibility exists that the sealant bottle may leak or may have otherwise been removed from the vehicle. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk.

When opening the rear hatch, the rear spoiler rests at the roof edge, which can result in damage to the rear spoiler and roof if the hatch is forcefully opened when the rear spoiler is bulged over (picture 1-2). Cause In the event of higher outside temperatures, the spoiler of the rear-end door thermally expands and may be above the roof by several millimeters. When opening the rear hatch when the rear spoiler is in a bulged condition, this can result in a collision between the rear spoiler and the roof edge. The cause may be related to fastening clips of the rear spoiler that have become loose. Remedy Remove rear spoiler, replace all fastening clips. Install rear spoiler again. In the event of damage, repair the vehicle. After assembly of the rear spoiler, check whether the clip is completely locked: When the rear-end door is open, press against the rear spoiler with your thumbs with around 5 kg of pressure (picture) 4). If it is possible to easily press the rear spoiler against the roof edge, the clip is not locked or may be damaged.

Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: Perform SCN coding in control unit OMSH223 (N168). For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

Cause Under analysis Remedy 1. Grease liftgate lock at the marked position with A0009893860 and then carry out an additional drive to assess the noise. 2. If the noise is remedied, vehicle return to the customer 3. If the noise continues, please create TIPS case with videos of the problem and send to the Body/Chassis/Entertainment inbox.

Cause Under analysis. Remedy Please create a TIPS case with the below information and send to the Body/Chassis/Entertainment inbox. -- Video of the complaint with and without the rear hatch interior trims installed. -- Vehicle history (accidents, damage, etc.)

Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

Cause The cause is being clarified. Remedy If wind noises can be clearly attributed to the roof railing, create a TIPS case with the following information: Detailed pictures of the roof railing in the actual state Detailed pictures of the roof railing in the taped-up state List of the work to pinpoint the cause Result of test to see whether the component part moves -> establish there is no rattle

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.

A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: Hitting the curb/posts with the front wheels. Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). Cracks (1) High pressure cleaner (2) Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

- The departure time, charging pause, location-based charging or target SOC limit is automatically set to 50% or to a random value in the Mercedes me application or in the charging settings on the head unit display. (Picture 1 & 3) - Incorrect notifications appear in the Mercedes me application for charging-related functions. (Picture 2) Related DTCs in quick test: No related fault codes (DTCs) are stored in the relevant control units. CPC3 - N127 (Drivetrain control unit) OBL223_GEN4 - N83/11 (Alternating current charger for high-voltage battery) DCB223 - N116/5 - Direct current charge connection unit (DCCU) Picture1 The target SOC limit is automatically set to 50% or any random values during charging. Picture 2 Incorrect notification Example Unable to unlock charging cable. Picture 3 Incorrect settings of charge interruption or pause. (If applicable) Cause - The Customer shares their Mercedes me credentials (password) with a third-party application, for example, a wall box application. This causes the Mercedes Benz backend server to receive random requests to reset the maximum SOC, departure time, charging pause, etc. - Charging settings are set incorrectly, for example, incorrect departure time, charging program, charging interruption/ pause, etc. Remedy The remedies below may vary depending on the customer complaint. Refer to the remedy that best matches the customer complaint. Remedy 1: The target SOC limit is automatically set to 50% or to random values during charging. - Change the Mercedes me login password on the Mercedes me homepage. (My Account > Login and Security > Reset). (Refer to Annex 1). Previously granted authorizations should then be revoked so that the charging settings can no longer be changed by external applications. Advise customers not to share the new password again. - Are there any sub-users? If yes, revoke their rights and reassess the function. -If differences between the vehicle and the Mercedes me app are visible, a new synchronization is recommended. Turn off Digital Extras through the Mercedes me app or the MMCR portal, and then turn the services on again. Remedy 2: Incorrect notifications in the Mercedes me app for charging-related functions. - Restart synchronization between the app and backend. Turn off Digital Extras through the Mercedes me app or the MMCR portal, and then turn the services on again. (Refer to Annex 2) Remedy 3: Incorrect charge interruption or pause setting. - Perform a factory reset of the head unit (A26/17). (Home > Functions > System > Reset), or turn off/correct all charging settings. (Refer to Annex 3) Additional Information: (Good to know) The LED on the charging inlet or socket indicates whether charging is completed or paused. 1) If the target SOC is reached, the charging inlet LED lights up Blue/Green without flashing. 2) If charging is paused, the charging inlet LED lights up orange without flashing. Additionally, the head unit charging settings display a charging pause. Note: Do not replace any hardware components for these complaints. If the complaint cannot be solved, please contact via TIPS or CAC.

The white LED on the charging inlet completely goes OFF after plugging in the charging cable. Related DTCs in quick test: There are no related fault codes (DTCs) stored in relevant control units. CPC3 - N127 (Drivetrain control unit) OBL223_GEN4 - N83/11 (Alternating current charger for high-voltage battery) DCB223 - N116/5 - Direct current charge connection unit (DCCU) Cause Control pilot (CP) circuit in DCB (N116/5: Direct current charge connection unit) might be not functional due to electrical overstress from EVSE (Electric Vehicle Supply Equipment | Charging Station). Remedy Refer to the charging cable actual values in DCB (N116/5). The actual value Charging cable at charging station and status of pilot function shows Charging cable NOT PLUGGED IN & CP not connected respectively, even though the charging cable is connected on both sides. This confirms a possible breakdown of Control Pilot (CP) circuit inside the DCB. Measurement of the resistance of Proximity Pilot (PP) and Control Pilot (CP) at the charging socket (G10) (see Annex Resistance measurement Proximity Pilot (CP) and Control Pilot (CP))

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

(transmission mount) A 243 240 25 00 can cause the noise complaint. Remedy Replacing parts will have no useful effect. Remove affected bearing and coat with anti-seize agent A 000 989 36 60 (Krytox), as specified in pictures, and install bearing again.

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.

Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

See Example Noise attachment Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy IMPORTANT: Do not apply document to vehicles outside of the listed validity range. The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. How to identify currently installed springs: Check for colored dots on the front springs. If no dots or color markings, please check if there is a parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please check for a barcode label with a 3 digit number. See "Spring Barcode" picture for example. Open a TIPS case with this number and list that it is from the barcode attached to the currently installed spring. If none of the above references can be found, open a TIPS case. How to identify next spring in line with color dots: Navigate to the parts catalog and enter the vehicle VIN/FIN. Navigate to group 32 sub-group 054 (front spring strut) and find the spring. The spring listed in the parts catalog will have a "color marking" indicator. If the dots on the spring and the color listed in the parts catalog is the same then you have the part number of the currently installed spring. If it does not, then you need to clear the vehicle specific filter by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). Proceed to finding the spring that matches the color dots on the vehicles currently installed spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".) How to identify next spring in line with part number tag: Navigate to the parts catalog and enter the vehicle VIN/FIN and the part number found from the spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. To do this, you need to clear the filters by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures).

See Example Noise attachment Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy IMPORTANT: Do not apply document to vehicles outside of the listed validity range. The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. How to identify currently installed springs: Check for colored dots on the front springs. If no dots or color markings, please check if there is a parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please check for a barcode label with a 3 digit number. See "Spring Barcode" picture for example. Open a TIPS case with this number and list that it is from the barcode attached to the currently installed spring. If none of the above references can be found, open a TIPS case. How to identify next spring in line with color dots: Navigate to the parts catalog and enter the vehicle VIN/FIN. Navigate to group 32 sub-group 054 (front spring strut) and find the spring. The spring listed in the parts catalog will have a "color marking" indicator. If the dots on the spring and the color listed in the parts catalog is the same then you have the part number of the currently installed spring. If it does not, then you need to clear the vehicle specific filter by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). Proceed to finding the spring that matches the color dots on the vehicles currently installed spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".) How to identify next spring in line with part number tag: Navigate to the parts catalog and enter the vehicle VIN/FIN and the part number found from the spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. To do this, you need to clear the filters by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".)

See "Sound Example" attachment. Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy IMPORTANT: Do not apply document to vehicles outside of the listed validity range. The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. How to identify currently installed springs: Check for colored dots on the front springs. If no dots or color markings, please check if there is a parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please check for a barcode label with a 3 digit number. See "Spring Barcode" picture for example. Open a TIPS case with this number and list that it is from the barcode attached to the currently installed spring. If none of the above references can be found, open a TIPS case. How to identify next spring in line with color dots: Navigate to the parts catalog and enter the vehicle VIN/FIN. Navigate to group 32 sub-group 054 (front spring strut) and find the spring. The spring listed in the parts catalog will have a "color marking" indicator. If the dots on the spring and the color listed in the parts catalog is the same then you have the part number of the currently installed spring. If it does not, then you need to clear the vehicle specific filter by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). Proceed to finding the spring that matches the color dots on the vehicles currently installed spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".) How to identify next spring in line with part number tag: Navigate to the parts catalog and enter the vehicle VIN/FIN and the part number found from the spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. To do this, you need to clear the filters by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".)

Cause A26/17 - MBUX multimedia system (head unit) software Remedy Update the A26/17 - MBUX multimedia system (head unit) to newest/latest software. Then recommission steering wheel electronics N135 - steering wheel electronics (LRE). If the problem is still present, please create a TIPS case. Note: Please do not replace any parts.

See Example Noise attachment Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. Verify currently installed spring in vehicle with use of color dots. NOTE: If no dots or color markings, please check the parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please open a TIPS case. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool.

See Example Noise attachment Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. Verify currently installed spring in vehicle with use of color dots. NOTE: If no dots or color markings, please check the parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please open a TIPS case. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number. IMPORTANT: Do not apply document to vehicles outside of the listed validity range.

No warning message is displayed and no fault codes are stored. Steering assist returns to normal after key cycle or at speeds greater than 7 MPH but condition may return until remedy is performed. Cause Software in the electric power steering (ES) N68. Remedy Perform software update of electric power steering (ES) N68. Disclaimer NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

Cause Signal timing error. Remedy 167: SW has been released. Update the FSAM to the latest SW version. 465, 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

EQE, EQS, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (118, 167, 192, 206, 223, 232, 243, 247, 254, 290, 294, 295, 296 and 297 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for a better entertainment experience. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

Cause There may be limitations on the indicator in the display due to incorrect parametrization in the head unit and PTCU SW. Remedy Open and XSS ticket and request "Delete code O98 from the data card" After, perform SCN coding for HU7 and PTCU software update (N127)

Cause Many possible root causes Remedy *Note - This Li does not apply if there are other Li's that apply to your concern OR you have a fault and/or guided test that leads to a root cause. AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements (Template attached to be used for submission of Warranty claim and/or TIPS case) Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements Cooling Capacity Test (If System Has a Charge) Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs - Warranty Submission Requirements on the Repair Order Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found

to: Summer heat Direct sunlight Lack of air conditioning or ventilation Camera enters self-protection mode to prevent overheating. Remedy Do NOT replace any parts. The driver camera (NTG7: MDC295; CIVIC.i2: CIVIC206) is operating as designed. Allow the interior to cool down. If the message remains after cooling: Run XENTRY Diagnosis Check latest software for Actuation of Driver Camera (A26/17) No TIPS case required.

Cause There may be limitations on the indicator in the display due to incorrect parametrization in the head unit and PTCU SW. Remedy PTCU software update (N127)

NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not preauthorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

function).</p><p>The result is a constant beep tone because no valid finger is detected and therefore no corresponding user profile can be assigned. </p> Cause <p>Software bug in A105 touchpad (TPAD).</p> Remedy <p>Perform software update in A105 touchpad (TPAD).</p>

Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify.

Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: Fluid intrusion Broken bushings or physical damage See attachments. Remedy If a component needs replacement but shows no visible external damage, submit a detailed TIPS case only when technical support is required. Include details of all connected external devices (such as charging cables, USB drives, and hard drives). If diagnostic results directly indicate component replacement, a TIPS case is not necessary.

Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: Fluid intrusion Broken bushings or physical damage See attachments. Remedy If a component needs replacement without visible external damage, submit a detailed TIPS case. Include information on all connected external devices (e.g., charging cables, USB drives, hard drives).

contactors for the DCCU are jammed closed and must be reset via Xentry. Short test found fault code P154B00 in PTCU warning for stuck contactor. Remedy Check for new DCCU (N116/5) SW. Perform SW update to DCCU (N116/5) via XENTRY. Reset contactors through special procedures through N116/5. If no new SW is available - Open TIPS case. Please provide HV CUL and QT in TIPS case.

G-Class (243, 294, 295, 296, 297, 465 platform) vehicles, a new NACS adapter informational label is required for the use of an approved Mercedes-Benz DC Fast Charging Adapter.

Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.