2020 Mercedes-Benz CLA 250 4Matic TSBs

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by doubleclicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module NOTE: Occasionally to verify complaint, the steering column/vehicle needs to be in direct sunlight or hot conditions for a few hours. If noise only occurs when adjusting the steering column via electric actuation, please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on all pivot points including, but not limited to, green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, wipe excess grease off and perform greasing and movement to limit stops in all directions again. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. Include detailed items of the following: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again and anywhere there are movement or friction points that the noise seems to be emanating from. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 double-click on the locking button As of modification year 22/1, by pressing and holding the locking button + double-clicking on the release tab On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The instrument cluster message and the FC memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 206 and 223 with code 802: Perform a software update and SCN coding for the control unit "N83/11 - AC charger for high-voltage battery (SGLG)" in order to remedy the problem. For model series 243: The correction is already available. Perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The instrument cluster message and the FC memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 206 and 223 with code 802: Perform SCN coding in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Please do not replace any parts even if the FC P0CFE00 coding continues to appear after successfully completing this step. A new software fix is currently in development and will likely be published in 01/2026. Replacing parts will not remedy the issue. For model series 243: The correction is already available. Perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10P067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. Please update the Head unit software to E505.9

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.

menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The robustness measure has been identified and is planned for implementation in the A26/17 E505.9 software. The E505.9 software is expected to be available in XENTRY Q3 2026.

The UI continues to show the old stations artwork instead of updating to the new one. Cause Root cause currently being investigated. Remedy Please do not replace any parts. Please create a TIPS case to Body/Chassis/Entertainment inbox.

the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.

Cause Under Analysis Remedy 1.Reset the MBUX language (e.g., if the MBUX language is set to English, please change it to any other language and then set it back to English again) 2.If the issue still persists after the step 1, Perform a user data reset of the Head Unit. If the above 2 steps still don't repair the issue, please open a TIPS case. Note: Please do not replace any parts

the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.

When performing a quick test, the following fault code is stored in Y3/14 Transmission control for 8speed dualclutch transmission (DKG): P24F100 The wakeup line of the control unit has a short circuit to positive. Cause Possible signal timing between EZS control unit and Transmission Control Unit (DKG) Remedy As of 7/15/2026, new SCN coding is available for the EZS control unit. IPR will advise to open a TIPS case for EZS (N73), this is due to GLA models requiring support for SCN coding procedure. GLB (X247) and CLA (118) No TIPS case necessary. 1. SCN coding of EZS Control Unit 2. Clear all faults and perform extended road test with multiple drive cycles GLA (H247) Special function password required. 1. Verify if special procedure Central Locking Development Data is present in EZS (figure 1) 2. Submit a TIPS case to the Powertrain Inbox with the following information: Initial Quick Test w/ freeze frame data IPR Result DKG Control Unit Log EZS Control Unit Log Initial EEPROM data EZS special procedure menu If the vehicle has had this LI performed and P24F100 has returned, please submit a TIPS case to the Powertrain Inbox.

enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage Detection ("DMTL") on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership. Why the Warranty extension? On certain Model Year 2018 - 2024 A / C / CLA / CLS / E / G / GLA / GLB / GLC / GLE / GLS / GT / S / SL Mercedes-Benz vehicles, under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code ("DTC") entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp ("MIL"). Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be covered under this extended warranty and performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (MIL).

Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

-Engine runs rough. -Poor shifting or jerking when accelerating. -Fault codes stored related to mixture formation, injector quantity adjustment, or misfire. Note: One or more of the above symptoms can occur. It is possible that no fault codes are stored. Cause Leaking valve seat in cylinder head. Remedy -Perform cylinder leakage check as noted in WIS group 01.00. If excessive leakage is found determine if leak is from intake or exhaust valves. -If leakage is found from intake or exhaust valves, remove cylinder head and inspect valve seats. -The complete cylinder head must be replaced if valve seat damage is found. The valve seats can not be reworked. -Engine oil and filter should be changed after the repair. Workshop notes cylinder head repair: 1. The intake rocker arm roller is narrower than the exhaust and they must not be interchanged. Mark the rocker arms so they are reinstalled in their original location. 2. Inspect all parts that are being reused (i.e. camshafts, rocker arms) for signs of wear or damage. See WIS doc AH05.20-P-1000-09SZ for examples of normal and abnormal wear. Replace parts with new if damage or wear is found. 3. Check that all rocker arms are correctly located on the camshaft before installing cylinder head cover. Rotate engine at least 2 times and check that there are no problems with rocker arms. 4. The timing chain tensioner can be reused if it extends fully, has no noticeable problems in prior operation, and no chain drive components were replaced. 5. Care must be taken when removing fuel injectors to prevent damage. See WIS doc AR07.03-P-0004-03MM. 6. Cleanliness must be observed during repair to prevent subsequent complaint or engine damage: When cleaning engine block surface, ensure oil ports are sealed to prevent debris from entering oil circuit. Refer to SI01.40-P-0010A. No abrasive materials, sharp-edged tools, or unapproved cleaners should be used on engine block surface. Refer to AR01.00-P-0050-01A. Any debris from cleaning that has entered the cooling jacket should be removed before assembly of engine. The debris can otherwise cause blockage in the cooling circuit leading to engine overheating. If any of the parts listed below are found damaged or in need of replacement during cylinder head valveseat diagnosis or repair, and the vehicle has warranty coverage, they must be claimed on a separate partsonly line. These items are not covered under the cylinder head warranty extension and cannot be included with the claim. Camshafts Camshaft adjustment solenoids Camshaft positioners Fuel injectors Hydraulic valve play compensating elements Roller rocker arms Spark plugs Timing chain Timing chain guide rails

Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% a negative charge balance A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked). Vehicles with code B01+801: When charging while stationary, the 48V battery must have a state of charge (SOC) of 70% before the 12V primary battery, or the secondary battery in the case of code 503, can be charged. To ensure optimum battery care, please also comply with the existing Service Information documents regarding the handling of stock vehicles (SI54.10-P-0024A) and on remaining in transport mode (SI54.00-P-0004A) until immediately before handover to end customers. Special note: Do not replace any parts, if the message has occurred due to battery discharge as a result of the driving profile or the ignition being switched on (see attached examples); in such cases separate warranty and goodwill invoicing is not possible, as this is a normal on-board electrical system protection function. Likewise battery care and recharging do not qualify as a W&G case. Please advise customers accordingly regarding the above-mentioned issues relating to vehicle use.

control unit software for the engine electronics does not correspond to the current series production configuration. This may cause the electrical fault diagnosis of the lambda sensor to not operate as intended, so that in the event of a fault, the check engine indicator lamp may not illuminate. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the software for the engine electronics control unit on the affected vehicles.

-Engine runs rough. -Poor shifting or jerking when accelerating. -Fault codes stored related to mixture formation, injector quantity adjustment, or misfire. Note: One or more of the above symptoms can occur. It is possible that no fault codes are stored. Cause Leaking valve seat in cylinder head. Remedy -Perform cylinder leakage check as noted in WIS group 01.00. If excessive leakage is found determine if leak is from intake or exhaust valves. -If leakage is found from intake or exhaust valves, remove cylinder head and inspect valve seats. -The complete cylinder head must be replaced if valve seat damage is found. The valve seats can not be reworked. -Engine oil and filter should be changed after the repair. Workshop notes cylinder head repair: 1. The intake rocker arm roller is narrower than the exhaust and they must not be interchanged. Mark the rocker arms so they are reinstalled in their original location. 2. Inspect all parts that are being reused (i.e. camshafts, rocker arms) for signs of wear or damage. See WIS doc AH05.20-P-1000-09SZ for examples of normal and abnormal wear. Replace parts with new if damage or wear is found. 3. Check that all rocker arms are correctly located on the camshaft before installing cylinder head cover. Rotate engine at least 2 times and check that there are no problems with rocker arms. 4. The timing chain tensioner can be reused if it extends fully, has no noticeable problems in prior operation, and no chain drive components were replaced. 5. Care must be taken when removing fuel injectors to prevent damage. See WIS doc AR07.03-P-0004-03MM. 6. Cleanliness must be observed during repair to prevent subsequent complaint or engine damage: When cleaning engine block surface, ensure oil ports are sealed to prevent debris from entering oil circuit. Refer to SI01.40-P-0010A. No abrasive materials, sharp-edged tools, or unapproved cleaners should be used on engine block surface. Refer to AR01.00-P-0050-01A. Any debris from cleaning that has entered the cooling jacket should be removed before assembly of engine. The debris can otherwise cause blockage in the cooling circuit leading to engine overheating. If any of the parts listed below are found damaged or in need of replacement during cylinder head valveseat diagnosis or repair, and the vehicle has warranty coverage, they must be claimed on a separate partsonly line. These items are not covered under the cylinder head warranty extension and cannot be included with the claim. Camshafts Camshaft adjustment solenoids Camshaft positioners Fuel injectors Hydraulic valve play compensating elements Roller rocker arms Spark plugs Timing chain Timing chain guide rails Timing chain tensioner

May be most noticeable when transitioning from a coasting condition to accelerator pedal application. May occur in all drive modes. Cause Dualclutch transmissions (DCT) inherently exhibit more dynamic shifting behavior compared to other types of transmissions. This is due to the use of physical clutches for starting and gear changes. In certain situations, dynamic driving behavior can lead to a slight jerk sensation which is a normal technical characteristic of the transmission. A typical example is a "Change of Mind" situation: The customer is coasting towards a red traffic light. The traffic light turns green while the vehicle is still coasting. The customer then presses the accelerator pedal. In these situations, a slight jerk may occur briefly because the transmission must quickly engage the appropriate gear and control the clutches accordingly. Since shift forks are responsible for engaging the gears during shifting, a slight shifting noise may also be noticeable. Please note driving programs S, S+, and M are designed to provide sportier vehicle behavior and are not optimized primarily for maximum comfort, so this operation may be more audible. Remedy Verify the customer's concern and confirm proper transmission operation. If no faults or abnormal operating conditions are identified by IPR (Intelligent Predictive Repair), no hardware replacement is necessary. Inform the customer that the transmission has been designed to provide direct gear engagement and responsive vehicle performance. Under certain operating conditions, brief shift sensations may be perceptible and are consistent with the operating characteristics of the dualclutch transmission

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CPR = Car Package Release (For MB.OS) CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465, 906 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

Cause As part of the production process, the electrohydraulic controller units are subjected to a function test in an oil bath. Any oil residue remaining in the connector area can be regarded as production process-related. Since the oil used is a non-conducting, non-corrosive medium, the oil residue does not cause any technical impairment and does not result in any consequential damage. Remedy No action or replacement of parts is required! If necessary, clean the connector using compressed air only. Do not use any cleaning agents such as brake cleaner, as this could potentially cause consequential damage!

Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

See Example Noise attachment Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy IMPORTANT: Do not apply document to vehicles outside of the listed validity range. The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. How to identify currently installed springs: Check for colored dots on the front springs. If no dots or color markings, please check if there is a parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please check for a barcode label with a 3 digit number. See "Spring Barcode" picture for example. Open a TIPS case with this number and list that it is from the barcode attached to the currently installed spring. If none of the above references can be found, open a TIPS case. How to identify next spring in line with color dots: Navigate to the parts catalog and enter the vehicle VIN/FIN. Navigate to group 32 sub-group 054 (front spring strut) and find the spring. The spring listed in the parts catalog will have a "color marking" indicator. If the dots on the spring and the color listed in the parts catalog is the same then you have the part number of the currently installed spring. If it does not, then you need to clear the vehicle specific filter by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). Proceed to finding the spring that matches the color dots on the vehicles currently installed spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".) How to identify next spring in line with part number tag: Navigate to the parts catalog and enter the vehicle VIN/FIN and the part number found from the spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. To do this, you need to clear the filters by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures).

See Example Noise attachment Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy IMPORTANT: Do not apply document to vehicles outside of the listed validity range. The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. How to identify currently installed springs: Check for colored dots on the front springs. If no dots or color markings, please check if there is a parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please check for a barcode label with a 3 digit number. See "Spring Barcode" picture for example. Open a TIPS case with this number and list that it is from the barcode attached to the currently installed spring. If none of the above references can be found, open a TIPS case. How to identify next spring in line with color dots: Navigate to the parts catalog and enter the vehicle VIN/FIN. Navigate to group 32 sub-group 054 (front spring strut) and find the spring. The spring listed in the parts catalog will have a "color marking" indicator. If the dots on the spring and the color listed in the parts catalog is the same then you have the part number of the currently installed spring. If it does not, then you need to clear the vehicle specific filter by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). Proceed to finding the spring that matches the color dots on the vehicles currently installed spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".) How to identify next spring in line with part number tag: Navigate to the parts catalog and enter the vehicle VIN/FIN and the part number found from the spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. To do this, you need to clear the filters by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".)

Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

Cause Signal timing error. Remedy 167: SW has been released. Update the FSAM to the latest SW version. 465, 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

Cause Many possible root causes Remedy *Note - This Li does not apply if there are other Li's that apply to your concern OR you have a fault and/or guided test that leads to a root cause. AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements (Template attached to be used for submission of Warranty claim and/or TIPS case) Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements Cooling Capacity Test (If System Has a Charge) Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs - Warranty Submission Requirements on the Repair Order Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

(see attachment) Cause The cause is currently being investigated. Remedy Update the HU7 to the latest software version, then perform a factory reset of the HU7. Steps to perform factory reset: Navigate to Settings > System > Reset > Reset to factory settings and confirm If the problem persists, please record HU7 log and also a trace of the Body CAN (For Star 2 Body Can 1 and for Star 3 Body Can 2) during the symptom and send via a TIPS case to the Body/Chassis/Entertainment inbox. Note: Only collect and submit the log and trace if the symptom can be reliably reproduced.

TIREFIT sealant bottle may not meet specifications. The possibility exists that the sealant bottle may leak or may have otherwise been removed from the vehicle. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk.

NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not preauthorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.