2025 Mercedes-Benz AMG SL63 S E TSBs

This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 Allwheel drive (ARS) N127 'Drivetrain' (PTCU) control unit Y3/8 Transmission control for 9gear transmission (VGS) N3/10 Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications Collect an oil sample of the original fluid 5. Complete all transfer case Techin processes located under VG Control Unit > Adaptations Resetting the oil service data Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature (>60C ) 6. Operate vehicle in full circle with steering at full lock 5x to the left 5x to the right Return the vehicle to the client and request they drive the vehicle for at least 200 miles and return if the concern is not resolved. The extended drive will ensure the clutches are properly conditioned with the new oil and should resolve the concern. If this LI has already been applied to the vehicle, please submit a TIPS case to the Powertrain inbox with the following information: Initial quick test with fault freeze frame data Initial transmission EEPROM data VGS and Transfer Case Control Unit Log (N45 or N15/7) Special Acquisition Data .txt file (Transfer Case Control Unit > Special Procedures > Procedures for support queries to market support > Special Data Acquisition) Photo of the original oil condition What color was the fluid drained from the transfer case before the oil change? Was an oil sample collected, and can you provide a photo of the original fluid? What color and part number fluid was used during the oil change? How far was the vehicle driven after?

Cause Frictional vibrations Remedy The intent of this document is to reduce noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some scenarios are normal and some are induced by driving style like those listed below: Driving style such as two footed driving where the pad might be in constant contact with the rotor. Brake pressure and application style (stopandgo traffic with consistent light brake pressure riding brakes where the brakes cannot cool sufficiently between applications). This can cause the brake pads to glaze and have a smooth/glassy surface which can induce noise. When ambient temperatures rise during summer peak and during cooling and cold winter months. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 34 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to reassessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the pistonside brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and reapply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper /carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the pistonside brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off

software application causing elevated K81/K27/B05 fill time adaptations and elevated torque adaptations for concerning shift. Note: Shift quality in E Performance models can be affected if the HV Battery state of charge (SOC) reaches 25% or below. Remedy Check VGS software level, and follow relevant remedy instructions. (see attachment) AMG 43 models with VGS software levels up to 22A: As of 4/18/2025, an aftersales software improvement has been released. This software has been implemented in production as of model year 2024, however this LI should still be followed if the concern is present. 232 A0009025699 206 A0009025599 Please ensure your Xentry machine is up to date with the latest Add Ons and continue with the following steps: Note: ALL steps must be performed to rectify concern 1. Perform software update all control units included in VGS software update. 2. Check transmission oil level and correct, if necessary (transmission oil temperature > 60 C) 3. Perform Xentry Valve Flushing procedure at least 3x 4. Perform resetting of deceleration values (VGS > Special Procedures > Special procedure > Resetting learned values Deceleration mode) 5. Perform a standstill adaptation, then read out new EEPROM data 6. Perform driving adaptation(s) while adhering to the below parameters for at least 2030 miles. Note: There is no menu in Xentry for this procedure. We recommend displaying the torque in the instrument cluster. If all below parameters are met at the time the shift, a driving adaptation will automatically occur. Harsh 12 Perform a driving adaptation of 45 (adapts K81 for the 12 shift) Harsh 23 Perform a driving adaptation of 67 (adapts B05 for the 23 shift) Harsh 34 Perform a driving adaptation of 34 (adapts K27 directly) See attached PDF for min/max torque, and RPM parameters Transmission oil temperature > 30C (>86F) Level track (no incline/decline) Slippery drive program Display the torque in the instrument cluster Constant engine torque Do not shift via paddle AMG 63 models with VGS software levels up to 22A: No aftersales software resolution is planned. Perform above steps and release the vehicle. If the vehicle returns and already had ALL steps in this LI performed on a previous visit, or has software level 23A and newer: Please submit a TIPS case to the Powertrain inbox and ensure the following is included: Initial Quick Test w/ Freeze Frame Data VGS Control Unit Log Initial EEPROM (before any adaptations or Xentry procedures were performed) Detailed vehicle history of the complaint

investigation) Remedy If oil leaks are found at left or right cylinder head cover area please collect the following information and open TIPS case. 1. Collect photos of the leak 2. Include close up and wide view photos to accurately represent the location 3. Include if the vehicle has a "check oil level" Light on in the cluster or fault codes 4. Check oil level as per WIS to verify level and calculate possible oil loss from the leak 5. Identify and communicate the severity of the leak and provide supporting documentation 6. Open a TIPS case with the above information and submit to the Powertrain team for processing

It will also ensure that if a case is necessary, all supporting documentation is available. This should not be used on its own as justification for creating a TIPS case. Cause The root cause will vary depending on the complaint. The goal of this document is to provide diagnostic checks and procedures that may help resolve customer complaints without opening a TIPS case. Remedy Before opening a transmission-related TIPS case, the following steps must be performed to ensure all relevant data has been collected and possible remedies (when applicable) have been performed. Please Note: At minimum, the documents below must be collected before proceeding to ensure the data in its original state when the vehicle arrived is captured. - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - Initial EEPROM data (.txt format) - IPR Result (if applicable. See LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool) - Transmission Heath Page If the vehicle has previously been repaired for the same concern, note the date, mileage, and TIPS case or RO number, along with a brief description of the prior work performed. IPR Guidance: The IPR recommended repair should be completed prior to following any steps in this LI and prior to case creation. IPR repairs do not require additional warranty approvals or a TIPS case to validate/confirm the results. To ensure efficient case handling, please avoid opening TIPS cases for this reason. For further information regarding IPR please see the following documents: LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool Oil Pan Condition Evaluation: In some situations, IPR will advise checking the oil pan condition and determining a repair based on the evaluation. Example photos in Xentry can be found in two ways: Use the blue hyperlink in the IPR result, and it will take you to the Condition check of transmission oil Navigate to Xentry Bluebook > Help for control unit > Condition check of transmission oil If a different repair that what is recommended by IPR is performed, attaching photo documentation of the complaint vehicle oil pan and the IPR example to the claim is required. Reproducing the Concern: Proper evaluation of transmission concerns generally requires the condition to be reproducible. It is recommended to compare the vehicle to a similar model, if available, to help determine whether the shift behavior is characteristic of the drivetrain or uncharacteristic for the vehicle. If the concern cannot be duplicated: A test drive with the customer may assist in understanding and reproducing the complaint. The vehicle shift quality should be compared to a known-good vehicle with identical drivetrain and model year. Check Shift Quality History (VGS Control Unit > Adaptations > Shift Quality History) Shift Quality History will show the last 5 noticeable harsh shifts and some of the parameters in which it occurred. You can use this to attempt recreation of the operating conditions and increase likelihood of reproducing the complaint. Complaint A: Shift Quality Note: Certain AMG variants may exhibit more firm and noticeable shift behavior as a normal characteristic. Refer to LI27.60P075147 for additional information. 1. Perform Valve flushing procedure 2. Perform 5 Torque Converter adaptions in a row - Allow the vehicle to warm up naturally, DO NOT power brake as it will increase the temperature in the torque converter. - After the 5th adaptation, collect a screen shot showing all 5 on one page 3. Perform a standstill adaption - collect a screen shot Recheck vehicle operation. If the concern has not improved, driving adaptations should be performed to target specific gear shifts.

There are no drivability concerns related to this complaint. Cause Root cause varies Remedy Prior to performing any repairs for this complaint: With a cold engine, pressurize the high temp coolant circuit and while it's under pressure, release the cap on the low temp coolant circuit and check if the pressure drops right away or not. If the pressure drops, the lower coolant hoses are swapped. Correct this, fill, bleed and test drive the vehicle. If the complaint returns, then continue with the steps below. IMPORTANT: Use VMI to check for the following emission extended warranty > Engine Thermostat (incl. software update) MY19-23, Various Models and Platforms (167, 190, 205, 213, 217, 222, 223, 232, 253, 290, 463) If the vehicle is covered under the above emission extended warranty, please perform steps outlined in the accompanying NCU prior to those outlined in this document. If vehicle is not covered under the above emission extended warranty or the complaint continues to occur, then proceed as follows: Check for available software updates to the ME (N3/10). If updated software is available, perform the update, clear the DTC and the perform each of the "WARM START" and "COLD START" test drives listed below twice. If the code does not re-appear then release the vehicle. If there is no new software available OR the DTC returns after the test drives then perform the following steps: Drain the coolant through a fine mesh sieve and check for signs of debris. Additionally, inspect the coolant reservoir for debris. If any debris is found take pictures of the reservoir and the mesh filter and "flush" the system at least 2-3 times to clear as much of the debris as possible Replace the thermostat and bleed the system as outlined in AR20.00-P-1142-04A, evacuate the system for 20-30 minutes instead of the 5 minutes specified in step 22 NOTE: Please use all the tools specified in the AR document. The DTC will continue to populate if the circuit is not properly bled NOTE: There are two valid thermostats to choose from in the parts section of this LI. Please verify which PN is applicable for the vehicle being worked on via XENTRY Parts Information After bleeding the system clear the DTC and perform each of the "WARM START" and "COLD START" test drives listed below twice. If the DTC does not reappear after the tests, release the vehicle If the ME (N3/10) software is up to date, the thermostat has already been replaced, and the complaint persists open a TIPS case and attach the following documents: Initial quick test ME (N3/10) control unit log The results of an R48 test from a yes response and from a no response Pictures of the coolant reservoir and mesh sieve (mentioned above) WARM START Begin with the engine coolant temperature at approximately 50 degrees C Activate the AC system, if defrost is not in use open the windows Drive the car normally until a coolant temperature of 75 degrees C is achieved Depress the accelerator pedal 50% for ~5 seconds (partial acceleration) Let off the accelerator pedal and let the car coast for ~10 seconds Continue to drive the car normally COLD START Drive for ~7 miles (normal driving) Shut off the engine in a parking lot (or similar), wait 30 seconds, then restart and continue driving Depress the accelerator pedal 50% for ~5 seconds (partial acceleration) Let off the accelerator pedal and let the car coast for ~10 seconds Continue to drive the car normally

The Following DTC's are present P210185 - The throttle valve actuator has a malfunction. There is a signal above the permissible limit value. P213500 - The values from the position sensors of the throttle valve are implausible relative to each other P213600 - The values from position sensors "A/C" of the throttle valve are implausible relative to each other P210B85 - The throttle valve actuator 2 has a malfunction. There is a signal above the permissible limit value. P2AD300 - The values from the position sensors "A/G" of the throttle valve are implausible relative to each other Cause Increased electrical resistance in pins for left and right throttle actuators. (M16/60 and M16/61) Remedy Replaced left and right throttle actuator Sockets with updated part. Silver Coated Pins 8x A 003 982 70 26 (according to wiring diagram 0,5mm) Gold Coated Pins 4x A 003 982 75 26 (according to wiring diagram 0,75mm) ELA Seals 12x A 001 545 50 80

The Following DTC's are present P210185 - The throttle valve actuator has a malfunction. There is a signal above the permissible limit value. P213500 - The values from the position sensors of the throttle valve are implausible relative to each other P213600 - The values from position sensors "A/C" of the throttle valve are implausible relative to each other Cause Increased electrical resistance in pins for left and right throttle actuators. (M16/60 and M16/61) Remedy Replaced left and right throttle actuator Sockets with updated part. Silver Coated Pins 8x A 003 982 70 26 (according to wiring diagram 0,5mm) 4x A 003 982 75 26 (according to wiring diagram 0,75mm) ELA Seals 12x A 001 545 50 80

There are no drivability concerns related to the complaint. Cause Root cause varies Remedy Prior to performing any repairs for this complaint: With a cold engine, pressurize the high temp coolant circuit and while it's under pressure, release the cap on the low temp coolant circuit and check if the pressure drops right away or not. If the pressure drops, the lower hoses are swapped. Correct this, fill, bleed and test drive the vehicle. If the complaint returns, then continue with the steps below. IMPORTANT: Use VMI to check for emission extended warranty Engine Thermostat (incl. software update) MY19-23, Various Models and Platforms (167, 190, 205, 213, 217, 222, 223, 232, 253, 290, 463) If the vehicle is covered under an emission extended warranty, Please perform steps outlined in the NCU for repairs. If vehicle is not covered under an emission extended warranty, then proceed as follows: Check for available software updates to the ME (N3/10). If updated software is available, perform the update, clear the DTC and the perform each of the "WARM START" and "COLD START" test drives listed below twice. If the code does not re-appear then release the vehicle If there is no new software available OR the DTC returns after the test drives then perform the following steps: Drain the coolant through a fine mesh sieve and check for signs of debris. Additionally, inspect the coolant reservoir for debris. If any debris is found, flush the system several times to clear as much of the debris as possible Replace the thermostat and bleed the system as outlined in AR20.00-P-1142-04A, evacuate the system for 20-30 minutes instead of the 5 minutes specified in step 22 NOTE: Please use all the tools specified in the AR document NOTE: There are two valid thermostats to choose from in the parts section of this LI. Please verify which PN is applicable for the vehicle being worked on via XENTRY Parts Information After bleeding the system clear the DTC and perform each of the "WARM START" and "COLD START" test drives listed below twice. If the DTC does not reappear after the tests, release the vehicle If there is no new software available, the thermostat has already been replaced, and the DTC returns open a TIPS case and attach the following documents: Initial quick test ME (N3/10) control unit log The results of an R48 test from a yes response and from a no response WARM START Begin with the engine coolant temperature at approximately 50 degrees C Activate the AC system, if defrost is not in use open the windows Drive the car normally until a coolant temperature of 75 degrees C is achieved Depress the accelerator pedal 50% for ~5 seconds (partial acceleration) Let off the accelerator pedal and let the car coast for ~10 seconds Continue to drive the car normally COLD START Drive for ~7 miles (normal driving) Shut off the engine in a parking lot (or similar), wait 30 seconds, then restart and continue driving Depress the accelerator pedal 50% for ~5 seconds (partial acceleration) Let off the accelerator pedal and let the car coast for ~10 seconds Continue to drive the car normally

Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% a negative charge balance A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked). Vehicles with code B01+801: When charging while stationary, the 48V battery must have a state of charge (SOC) of 70% before the 12V primary battery, or the secondary battery in the case of code 503, can be charged. To ensure optimum battery care, please also comply with the existing Service Information documents regarding the handling of stock vehicles (SI54.10-P-0024A) and on remaining in transport mode (SI54.00-P-0004A) until immediately before handover to end customers. Special note: Do not replace any parts, if the message has occurred due to battery discharge as a result of the driving profile or the ignition being switched on (see attached examples); in such cases separate warranty and goodwill invoicing is not possible, as this is a normal on-board electrical system protection function. Likewise battery care and recharging do not qualify as a W&G case. Please advise customers accordingly regarding the above-mentioned issues relating to vehicle use.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

'A' has a short circuit to positive stored in VGS control unit. Cause Electrical failure of oil pressure sensor integrated into VGS Control Unit Remedy Intelligent Predictive Repair (IPR) recognizes this fault pattern and will provide the necessary repair suggestion. 1. Perform IPR and follow the recommended procedures 2. Replace complete EHS valve body, fill to near max fluid level, & complete initial start-up - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement.

Concern is mainly felt when coasting. Cause Parameters of the 54 neutral downshift (the shift method used in EV operation). Remedy This shift concern is considered normal for vehicles with this drivetrain. Hardware replacement does not change the root cause of the concern, as the observed shift behavior is characteristic of normal system function rather than a componentrelated fault. The following adaptations may improve the shift quality: 1. Check transmission oil level (transmission oil temperature > 60C) 2. Flush valves via Xentry procedure 3. Perform standstill adaptation 4. Perform driving adaptations for the 54 shift while following the below parameters: - Drive program: Slippery - Display torque in the instrument cluster - Do not shift using the paddles During coasting downshift 5-4: - Torque between 90 and 15 Nm (-66 and -11 ft-lb) - Maximum engine speed: 1,300 rpm

This is not an issue that affects drivability or performance and is not a safety concern. The vehicle remains safe to operate with this code, but the measures listed in the "Remedy" section are recommended. Remedy 1. Use VMI to check for Emission Extended Warranty Engine Thermostat (incl. software update) MY19-23, Various Models and Platforms (167, 190, 205, 213, 217, 222, 223, 232, 253, 290, 463) 2. If the vehicle is covered under the Emission Extended Warranty, Please perform steps outlined in the NCU for repairs. 3. If vehicle does not fall into the covered area of the Extended Warranty please check for Software updates to the ME control unit and then proceed with "Remedy Instructions" in attachments. Due to formatting issues please see "remedy instructions" in attachments

This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications - Collect an oil sample of the original fluid 5. Complete all transfer case Tech-in processes located under VG Control Unit > Adaptations - Resetting the oil service data - Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature ( >60C ) 6. Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Return the vehicle to the client and request they drive the vehicle for at least 200 miles and return if the concern is not resolved. The extended drive will ensure the clutches are properly conditioned with the new oil and should resolve the concern. If the concern continues to occur with the control unit disconnected or after the above steps have been performed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial quick test with fault freeze frame data - Initial transmission EEPROM data - VGS and Transfer Case Control Unit Log (N45 or N15/7) - Photo of the original oil condition - What color was the fluid drained from the transfer case before the oil change? - Was an oil sample collected, and can you provide a photo of the original fluid? - What color and part number fluid was used during the oil change? - How far was the vehicle driven after?

ME-SFI control unit software does not meet current production specifications. As a result, a check engine malfunction indicator lamp might erroneously be triggered. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the ME-SFI control unit software.

Vehicle has one or more DTC's Present P164B00, P164B09, P2B4400, P005A07, P005C07, P005A09, P005C09, P003C07, P2B5007, P003C09, P2B5009, P34C200, P34C109, P34C800, P34BE00, P34BD09 Cause Software and Hardware Remedy 1. Check for available Software updates for the Engine Control Unit ME N3/10. Perform update if available. 2. Check part numbers on ALL CAMTRONIC actuators to ensure latest part numbers are installed. 3. A177 982 03 03 and A177 982 17 00 should be replaced by A177 982 19 00 4. A177 982 02 03 and A177 982 16 00 should be replaced by A177 982 18 00 5. Remove engine cover and check for heat damage on the engine cover and wiring harness in the area above the engine compartment bulkhead and near the windshield. 6. In the event of wiring harness damage please open a TIPS case with photos of the harness and include a Lambda Line Graph Test for evaluation.

This is not an issue that affects drivability or performance and is not a safety concern. The vehicle remains safe to operate with this code, but the measures listed in the "Remedy" section are recommended. Remedy 1. Use VMI to check for Emission Extended Warranty Engine Thermostat (incl. software update) MY19-23, Various Models and Platforms (167, 190, 205, 213, 217, 222, 223, 232, 253, 290, 463) 2. If the vehicle is covered under the Emission Extended Warranty, Please perform steps outlined in the NCU for repairs. 3. If vehicle does not fall into the covered area of the Extended Warranty please proceed with "Remedy Instructions" in attachments. Due to formatting issues please see "remedy instructions" in attachments

the vehicle is stationary and ECO Start/Stop is active (combustion engine is off). The noise is more noticeable outside the vehicle and in acoustically shielded areas such as closed rooms or garages. Cause The noise in the valve body (EHS) is caused by superimposed pressure peaks acting on the valves. This phenomenon occurs only after a certain running-in period due to the influence of micro-contamination in the valve bores. Remedy A hardware modification of the electro-hydraulic control unit (EHS) is currently being implemented (no change to the part number). This will be incorporated into series production and as a spare part starting from 12/2025. This is only a comfort-related complaint and has no impact on the functionality or service life of the transmission. For sensitive customers, the following measures can be performed: 1. Replace the electro-hydraulic control unit (EHS), the oil pan, and the transmission fluid. - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement. (See attached location guide)

EEPROM or Transmission Health system following the replacement of the below components: - The electrohydraulic control unit (EHS valve body) in transmission 725.0/725.1 - The repair kit for the control unit (VGS) in transmission 725.0 Cause Missing, incorrectly installed, or damaged guide tubes on the EHS valve body. Remedy Check for the correct installation of the guide tubes (refer to attachments under Cause), correct installation if necessary. Parts Catalog References: NAG3M 725.1 AND NAG3C 725.0 (AMG only): Part numbers 100, 120, 150, 160 NAG3C 725.0 (Non AMG): Part numbers 280, 290, 330, 340 NOTE: If any of these guide tubes are not installed and the vehicle is driven, it will create several rinse and slipping events in the EEPROM data. These values caused by incorrect installation need to be erased to prevent future misdiagnosis. Submit a TIPS case to the Powertrain inbox with the following to receive the necessary reset password: - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - IPR Result - Initial EEPROM data (before repairs) - Latest EEPROM data - Photo of oil level ultrasonic measurement next to XENTRY specifications Please provide detail regarding the reasoning for the initial replacement in your workshop findings and measures performed. (This topic was covered in the July 2022 and July 2024 Passenger Car Tech Topics)

This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications - Collect an oil sample of the original fluid 5. Complete all transfer case Tech-in processes located under VG Control Unit > Adaptations - Resetting the oil service data - Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature ( >60C ) 6. Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right 7. Perform an extended 200mi road test to ensure the clutches are properly conditioned with the new oil. 8. Reassess the concern and release the vehicle if no longer present. If the concern continues to occur with the control unit disconnected or after the above steps have been performed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial quick test with fault freeze frame data - Initial transmission EEPROM data - VGS and Transfer Case Control Unit Log (N45 or N15/7) - Photo of the original oil condition - What color was the fluid drained from the transfer case before the oil change? - Was an oil sample collected, and can you provide a photo of the original fluid? - What color and part number fluid was used during the oil change? - How far was the vehicle driven after?

and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

starter-alternator defective Remedy Requirement: Before carrying out test work, it must be ensured that the person performing the work has successfully completed the required qualification for work on the high-voltage system. Note: In order to check whether the high-voltage belt-driven starter-alternator is defective, please carry out the test below. If the fault "P0E2F00 The electrical fuse B for the high voltage has a malfunction" is stored in the N82/10 BMS control unit, the HV protocol must be checked to see whether the fuse for the auxiliary consumers is defective. In this case, the high-voltage battery must be replaced after the short circuit has been eliminated. (See attachment) The defective high-voltage belt-driven starter-alternator must always be sent back via the existing return delivery process for analysis. Check: Please disconnect the high-voltage plug at the high-voltage belt-driven starter-alternator and connect test adapter 000 589 94 63 00. Measure resistance HV+ to HV-. If the final measurement result is between 01 ohm, the high-voltage belt-driven starter-alternator with the short circuit must be replaced. If either one of or both the fault codes P0C0B16 and P0C0B17 are saved in the high-voltage belt-driven starter-alternator control unit G2/3, please replace the high-voltage belt-driven starter-alternator, since no short circuit can be measured here and this therefore concerns a hardware defect. Please check the serial number on the silver adhesive label below the SW number on the front of the high-voltage belt-driven starter-alternator. Example: 2314300044 (the first 10 digits, see attachment) Important note: If the number is greater than 2329100027, a TIPS case must be created. In this instance, please attach the following documents to the TIPS case: Quick test High-voltage event log Picture of the silver adhesive label on the front of the high-voltage belt-driven starter-alternator (serial number) Attach the measurement results with pictures

Cause Frictional vibrations Remedy The intent of this document is to reduce or eliminate noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some of the scenarios are: Driving style Brake pressure and application style (stop-and-go traffic with consistent low brake pressure riding brakes where the brakes cannot cool sufficiently between applications). Ambient temperatures 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and re-apply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake application

Cause Frictional vibrations Remedy The intent of this document is to reduce or eliminate noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some of the scenarios are: Driving style Brake pressure and application style (stop-and-go traffic with consistent low brake pressure riding brakes where the brakes cannot cool sufficiently between applications). Ambient temperatures 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and brake paste as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". If adhesive is already installed on backing plate, you may gently scrape off and re-apply a new adhesive. In some instances the adhesive may be very carefully removed and Molykote applied instead. 4. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 5. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 6. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. e) Finally drive approx. 3 miles to allow the system to cool. f) Reassess noise.

Upon inspection oil will be seen at or around the rear of the engine and at the engine/transmission interface. Cause Oil leaking from rear main seal and/or rear main seal plate. Remedy If the rear main seal plate has been previously replaced per the instructions in this LI, open a TIPS case before proceeding. Inspect the rear main seal very carefully. Make sure the seal is not sucked in, rolled, or cut (see pictures in attachments). Confirm the leak location is at the rear main seal and/or rear main seal plate by cleaning the area thoroughly and applying trace powder to the suspected area. Allow the vehicle to run either on a lift or at low speed in a controlled environment (do not attempt at high speed or in wet areas as this will make the results difficult to assess). If the leak is emanating from the seal: replace both air/oil separators. Then clean the bellhousing area completely and test with trace powder again to see if the leak remains. If it doesn't, release the car. If the leak remains pull the rear main seal plate, clean the block mating surface completely and replace the rear main seal plate and rear main seal. When the new seal is installed make sure the sealant path is followed exactly as it is shown per the drawing in the attachments. Apply the sealant to the BLOCK instead of the plate to ensure adequate coverage is attained. After installation lubricate a feeler gauge with oil and run it between the rear main seal and the crank to clear any small debris that may be present and to break any binding or stiction.

with Easy Entry function), noise (breakaway noise) when leaving the limit stops of the height adjustment. Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Driver seat control unit software 2. Steering column height adjustment transmission Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Perform software update of driver's seat control unit 2. Replace repair kit for steering column height adjustment Procedure 1: Perform software update of driver seat control unit. ALL models except 205/253/293/222/217/231/463/213/238/257/290 up to special equipment code 801. Move out the fore/aft adjustment to the end position. Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward After releasing the jam, perform a software update of the driver's seat control unit If procedure 1 is not effective, there is no new software available for the driver seat control unit, or the chassis is not listed above (167, 223, 294, 206, 294, 295, 296, 297,232,214,254) then use procedure 2. Procedure 2: Replace repair kit for steering column height adjustment. Move out the fore/aft adjustment to the end position. Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward Remove footwell trim on driver's side. Determine type version of height adjustment in XENTRY Parts Information and order appropriate replacement part (refer to attachment). 1. Version A: A 231 460 77 00 2. Version B: A 205 460 38 03 Remove steering column. Remove height adjustment (adjustment repair kit). Install repair kit (adjustment repair kit) (observe tightening torque for screws in attachment). Install steering column. If possible, flash driver seat control unit to latest software release or code SCN again. Commission driver seat control unit (normalization of limit stops is deleted and learning process repeated).

Cause Potential causes: Assembly of the underfloor paneling with unloaded body (results in tension after compression of vehicle in K0- design level) Relative movement between front and rear engine compartment lining Torque loss of the screw connection Accumulation of stones and dirt Remedy Screw connection in K0-design level (vehicle sitting on ground on it's own weight) and taking into account the correct screw sequence Additional screw connection points (minimization of relative movement) Increase in tightening torque Integration of spacer rings (reduction of accumulation of stones and dirt) In order to rule out that other component parts may be responsible for the noise, remove the underfloor paneling first. If the noise complaints are NO LONGER present after removal, proceed with underfloor paneling rework. Underfloor paneling rework 1. Order after-sales kit with item number A2326207003 for the rework. 2. After receiving the after-sales kit (A2326207003), check the contents: 22 screws (A0109902604) / 14 rivet nuts (A0009902349) / 4 spacer washers (A2326207203). If the content is complete, start rework in the next step. 3. Disassemble underfloor paneling. If front and rear engine compartment lining are bonded to one another, order new parts (A2326201101, A2326268900). 4. Clean underfloor paneling and integral carrier. 5. Mark four additional screw connection points on the front engine compartment lining (see attachment 1). See appendix 2 for dimensions. 6. Drill holes with d=9 mm on the markings. 7. Screw front and rear engine compartment lining together using the screw connection points already available (see attachment 3). Both linings are therefore aligned to one another. Important: Pay attention to alignment of the elongated holes on the external edges. 8. Drill into the rear engine compartment lining using the four additional holes with d=9 mm (see attachment 4). 9. Disassemble front and rear engine compartment lining. 10. Drill out three existing rivet nuts with d=9 mm (see attachment 5). 11. Insert seven new rivet nuts (A0009902349) (see attachment 6). 12. Drill out seven existing rivet nuts in the integral carrier with d=9 mm (see attachment 7). Caution: Do not damage integral carrier. 13. Remove remaining rivets that have fallen off from the integral carrier using a magnetic tube (see attachment 8). 14. Insert new rivet nuts (A0009902349) in the integral carrier (see attachment 9). 15. Fix four spacer rings (A2326207203) in place using bonding points between underfloor paneling and integral carrier (for position, see attachment 10 and attachment 11). Caution: No adhesive can be applied to the contact areas (risk of torque loss). 16. Install underfloor paneling on vehicle with 16 Nm (observe screw sequence in attachment 12). Important: Use screw item number A0109902604.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". 5. Apply heat-resistant lubricating paste to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 6. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. e) Finally drive approx. 3 miles to allow the system to cool. f) Reassess noise.

Cause Potential causes: Assembly of the underfloor paneling with unloaded body (results in tension after compression of vehicle in K0- design level) Relative movement between front and rear engine compartment lining Torque loss of the screw connection Accumulation of stones and dirt Remedy Screw connection in K0-design level (vehicle compressed) and taking into account the correct screw sequence Additional screw connection points (minimization of relative movement) Increase in tightening torque Integration of spacer rings (reduction of accumulation of stones and dirt) -> see underfloor paneling rework instructions 1. Create a TIPS case and send to Body/Chassis/Entertainment inbox. 2. Attach video/recording of the noise problem to the case. Be sure the recording is clear and audible. 3. After entering the TIPS case, the aftersales kit required for rework is sent (the required parts are not yet available via the replacement parts service). 4. After receiving the aftersales kit (A2326207003), check the contents: 22 screws (A0109902604) / 14 rivet nuts + 1 replacement rivet nut (A0009902349) / 4 spacer rings (A2326207203) Underfloor paneling rework 1. Disassemble underfloor paneling. If front and rear engine compartment lining are bonded to one another, order new parts (A2326201101, A2326268900). 2. Clean underfloor paneling and integral carrier. 3. Mark four additional screw connection points on the front engine compartment lining (see attachment 1). See appendix 2 for dimensions. 4. Drill holes with d=9 mm on the markings. 5. Screw front and rear engine compartment lining together using the screw connection points already available (see attachment 3). Both linings are therefore aligned to one another. Important: Pay attention to alignment of the elongated holes on the external edges. 6. Drill into the rear engine compartment lining using the four additional holes with d=9 mm (see attachment 4). 7. Disassemble front and rear engine compartment lining. 8. Drill out three existing rivet nuts with d=9 mm (see attachment 5). 9. Insert seven new rivet nuts (A0009902349) (see attachment 6). 10. Drill out seven existing rivet nuts in the integral carrier with d=9 mm (see attachment 7). Caution: Do not damage integral carrier. 11. Remove remaining rivets that have fallen off from the integral carrier using a magnetic tube (see attachment 8). 12. Insert new rivet nuts (A0009902349) in the integral carrier (see attachment 9). 13. Fix four spacer rings (A2326207203) in place using bonding points between underfloor paneling and integral carrier (for position, see attachment 10 and attachment 11). Caution: No adhesive can be applied to the contact areas (risk of torque loss). 14. Install underfloor paneling on vehicle with 17 Nm (observe screw sequence in attachment 12). Important: Use screw item number A0109902604.

parking See video for example Cause Noise originates within the transmission valvebody Remedy Take a video from underneath vehicle recording the noise Pull EEPROM data, Inital Quick Test, and Control Unit Log Please open a TIPs case providing all data to assess next steps.

The update is free of charge and runs in the background, which takes about 8 minutes to install. During this time, the vehicle can be driven without any restrictions, and the new software will be active with the next ignition cycle. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

CarPlay over Wi-Fi Audio cuts out Device not recognized No operation possible Cause There are multiple possible causes for an iPhone disconnecting from a vehicles head unit while using Apple CarPlay. These include hardware, software, and environmental factors: Environmental Interference External Sources: Passing under toll bridges, driving near airports, or areas with heavy electronic interference (e.g., as described in LI82.85-P-076157) can cause connection drops. Cellular Networks: Interference from nearby cell towers operating on similar frequencies (usually 2.4GHz or 5GHz) can disrupt the signal. Storage Location: Keeping your phone in a handbag or surrounded by other objects inside the vehicle can create physical or electronic interference. Device and Software Issues Head Unit Software/Hardware: Outdated firmware, bugs, or hardware faults in the vehicles head unit can prevent a stable connection. iPhone Software/Hardware: Similar issues in the iPhone, including buggy iOS updates or hardware problems, may affect performance. Reset or Reboot: Automatic rebooting or resetting of either the head unit or the iPhone will temporarily disrupt CarPlay. Connection and Settings Wired Connections: Faulty Cable: A damaged or poor-quality USB cable can cause intermittent or total loss of connection. USB Port Issues: Dust, debris, or physical damage in the USB port of either the head unit or the iPhone can also lead to disconnects. Wireless Connections: Intermittent Bluetooth/Wi-Fi: Unstable wireless communication (Bluetooth/Wi-Fi) can frequently break the Car- Play connection. Power Management: Battery Saver Mode: Enabling low power mode may restrict background processes, affecting CarPlay. Vehicles Electrical System: Unstable power delivery from the cars battery or electrical interruptions can cause the head unit to malfunction. Phone & App Configuration Phone Settings: Incorrect or conflicting settings (especially Bluetooth or Wi-Fi) on your iPhone can interfere with the CarPlay link. Third-Party Apps/Profiles: Installed apps or configuration profiles may conflict with CarPlays operation. Native apps are apple maps, apple music, audio books, apple news, podcasts, messages and phone. All other apps are considered third party apps. App Conflicts: Running conflicting apps that require similar system resources as CarPlay can cause instability. Mobile Data Plan: Streaming from online sources without sufficient mobile data can result in lost connectivity. Other Factors Heat & Overheating: If either the phone or the head unit overheats, they may disable certain functions to prevent damage, leading to disconnection. User Actions: Accidentally disconnecting the device in settings, or physically moving or bumping the phone or cable, may disrupt the connection. Remedy FUP6 (E605.8) software has been released for the following chassis: 118, 177, 243,247,206,254,167,294,295,296,223, 297. Flash available software for the head unit and test for function. The LI will be updated once available for the remaining chassis. If the complaint remains after the SW update please continue with the steps below. Guided Diagnostic Path for Apple CarPlay Connection Issues: Please follow the steps below to systematically diagnose and resolve CarPlay concerns:Update Devices: Ensure the iPhone is updated to the latest available iOS version. Ensure the vehicles head unit is updated to the latest software version available. Isolate the Issue: Check whether the symptom persists with another iPhone running the latest iOS version. Test both wireless and wired CarPlay connections: Does the issue only occur with wireless CarPlay? Does the wired connection to the phone function correctly? Further Troubleshooting Steps: Reboot the iPhone. See attachment for further instructions.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

Cause The firmware installation was incomplete. Remedy In the A26/17 control unit "MBUX multimedia system" (head unit), use XENTRY to carry out the special process "All Modules"; this will reinstall the firmware completely.

Cause The firmware installation was incomplete. Remedy In the A26/17 control unit "MBUX multimedia system" (head unit), use XENTRY to carry out the special process "All Modules"; this will reinstall the firmware completely.

The following fault codes are stored in the PTCM control unit: P1CA000 B188C2A Cause If the trunk lid is repeatedly opened manually or the vehicle has experienced undervoltage, the trunk lid loses its normalization due to faulty software coding. Remedy For vehicles with a production date up to 01/22/26 (SL (232)) or 01/27/26 (GT (192)) 1. Update the HKS N121/1 control unit and perform SCN coding. (If no new software is available, still perform SCN coding) 2. Perform normalization of component 'N121/1 (Liftgate control control unit)'. Vehicles produced from January 22, 2026 (SL (232)) and January 27, 2026 (GT (192)) onward were factory-fitted with the correct Software Calibration Number Table.

implausible (>365 days) for the following conditions: for the date of the vehicle handover or the last conducted and confirmed Service A/B Cause Case 1: Observe the following on vehicles with a disconnected on-board electrical system battery (12V/48V): The period in which the on-board electrical system battery is disconnected cannot be counted by the maintenance computer. As soon as the on-board electrical system battery is connected again, the maintenance computer automatically starts counting without making a correction to the remaining time (days until the next service). Case 2: If a disconnected on-board electrical system battery (12V/48V) can be ruled out as the cause, it is possible that: The daily turnover counter inside the electronic ignition lock (EIS) has experienced memory loss. This anomaly was detected in the EIS software from modification year 2022 onward. To do this, please check the plausibility of the daily turnover counter as follows: If "TUSZ Assyst Plus" < the actual days since "Handover Date/DAY/Month/Year," then proceed to remedy for case 2. Information: A variation of 2-3 days is still considered plausible. If "TUSZ Assyst Plus" is plausible, or if a remaining time of 365 days is permanently displayed, check whether the vehicle has been handed over. These types of cases have different causes. (The respective values are included in the maintenance data in the control unit log of the instrument cluster). Remedy For case 1: When the on-board electrical system battery is disconnected, this period must always be taken into account for these vehicles, and the following condition must be met for a correct calculation to be made: (A): The number of days from the "date of vehicle handover or last service A/B" to the "date on which the vehicle arrived at the workshop." (B): Remaining time (days until the next service, as shown in the instrument cluster). (C): Days on which the on-board electrical system battery was disconnected. The formula requires the following condition to be complied with. 365 - (A) [days] = (B) - (C) [days] For case 2: If the on-board electrical system battery (12 V/48 V) was not disconnected and the remaining time shown in the customer or workshop menu on the instrument cluster (days until the next service) is implausible in terms of the date of the vehicle handover or the last performed and confirmed service A/B, or the condition in the formula was not met, the service can still be performed and confirmed. For vehicles arriving more than 90 days after the service due date, the DSB service history can only be corrected by re-entering "Vehicle regularly serviced." A software fix for the EIS (electronic ignition lock) is currently in planning. The objective is to have a remedy available for 2026. Until the remedy is available, it is advisable to inform the customer that the next service is due again after 365 days at the latest.

192 Cause Increased quiescent current Remedy 1. Conduct quiescent current measurement. DO NOT USE A DVOM IN LINE - this will blow the fuse in your meter. Use an amp clamp with either a DVOM or XENTRY Scope and wait until the vehicle has gone to sleep (usually takes 6-10 minutes). Once the vehicle is asleep, observe the quiescent current for 10-15 minutes and note down the values. A stable quiescent current should be less than 50 mA. Values higher than this figure are considered not OK (NOK) and require further analysis. 2. If the quiescent current is higher (> 50 to 100 mA): Check whether software updates are available for relevant control units: Door control units (DMD (N69/1), DMP (N69/2), DMRL (N69/3), DMRR (N69/4)), EIS (N73/3), PTCU (N127), OHCM (N70), GW (N73/3*1) After installing the updates: measure the quiescent current again If the quiescent current is < 50 mA, the vehicle is OK If the quiescent current is between 50 and 100 mA, continue with step 5 If the quiescent current is between 100 and 200 mA, continue with step 3 If the quiescent current is between 200 mA and 1 A, continue with step 4 3. For no-load current values of 100 to 200 mA: Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. Disconnect door separation points (A-pillar connection) when the vehicle is asleep, starting with the driver's side Document the quiescent current value If there is no change: Disconnect the door separation point on the front passenger side and note down the value again If the quiescent current falls below 50 mA after the door separation point is opened, the respective outer door handle must be replaced If the quiescent current drops below 50mA, the draw has been addressed and the vehicle can be released If the quiescent current remains above 50mA after the relevant door handles have been successfully replaced, please create a TIPS case to the LV/HV inbox and retain the removed door handles for the time being If the quiescent current does not change after the door separation point is opened, please carry out step 5 4. For quiescent current values between 200 mA and 1 A: Important: Before pulling out F320 and F304, the tow-away protection and interior protection must be deactivated to prevent an alarm from triggering Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. Wait until the vehicle has gone to sleep Pull out the fuses one after the other, starting with F323 (PTCU CU/N127), and note down the quiescent current value Perform the same test one at a time if the value is still high for each additional fuse: F119 (PTCU CU/N127), F324 (EIS CU/N73/3), F305 (EIS CU/N73/3), F320 (OCP CU/N70), F304 (OCP CU/N70) If pulling out the fuse reduces the quiescent current to below 50 mA, replace the corresponding control unit. After replacing, please measure and assess the quiescent current again If the quiescent current remains unchanged after the fuses listed above are pulled out, please carry out step 5 5. If the quiescent current remains above 50 mA after all controls have been implemented: Create a TIPS case Document all the completed steps and measurement results Attach the XENTRY Scope trace of the draws that you have seen and identify where certain steps were taken. Attach the latest N73 and N73/3*1 CUL's If the quiescent current is higher than 1 A, the bus keep awake control unit should be identified via the EIS gateway

87 32) may trigger a fault message ("48 V Service Required" with fault codes P0ADA91, P0ADE91, P0AA100, P0ADD00 or P0AA000) in the instrument cluster. This fault message may prevent the 48 V battery contactors from opening automatically if the 12 V power supply is interrupted. In this case, the 48 V on-board electrical system, including connected components, remain energized. Cause The contactors of the 48 V battery do not open, resulting in residual voltage (> 3V) even when the 12 V battery is disconnected. Remedy When working on the 48 V on-board electrical system or connected components, ensure the component being repaired is de-energized in the 48 V system after disconnecting the 12 V ground line. Use a DVOM and ensure that there is less than 3V across the 48V terminals. If the voltage is less than 3V, the repair can be continued in accordance with the WIS documentation. If the voltage is greater than 3V, disconnect the ground line from the 48 V on-board electrical system battery and secure from contacting any ground points of the vehicle before continuing the repair. Once the work has been completed, follow the procedure for clearing the 48 V battery fault message as specified.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Mercedes me services - activation not possible Notes: - The event code "B16AC00 - The configuration of the SIM card is erroneous" is active and stored - The head unit shows no internet connection Cause The RAMSES module may be faulty. This fault profile can be recognized as follows: With XENTRY Diagnosis, enter the "ACTUAL values" menu of the RAMSES control unit and read out the values with position 175 and 727. ACTUAL values in the event of a fault: Type of mobile service (position 175): No reception Operating mode (position 727): Ready mode Remedy If B16AC00 is permanently active and saved and position 175 is no reception and position 727 is ready mode, it is highly likely that the communication module is faulty. In this case, an initial start up must be carried out. If the problem persists even after an initial start up, please create a TIPS case.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

The following fault codes are stored in the Tailgate Control (HKS) control unit: P1CA000 & B188C2A Cause If the trunk lid is repeatedly opened manually or the vehicle has experienced undervoltage, the trunk lid loses its normalization due to faulty software coding. Remedy For vehicles with a production date up to 01/22/26 (232) or 01/27/26 (192): Update the HKS N121/1 control unit and perform SCN coding. If no new software is available, perform SCN coding. Vehicles with a production date 01/22/2026 (232) or 01/27/2026 (192) and later have already received the correct QNT from the factory.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

There is an implausible signal." In the quick test, there are also no other DTC's in other control units that point to or reference N80 Steering Column Control Module ("SCCM"). There is no effect on any other components or vehicle functions and it does not cause an instrument cluster light. Cause The DTC only ever occurs during initialization (initialization occurs after bus sleep). The SCCM then resets itself. Remedy 1. If the error is stored and no other control unit points to the N80 SCCM ignore and erase. Software expected in Q4 2026. 2.If the DTC is in the N80 SCCM AND the following DTC's are in N30/3 (Electronic Stability Program) and N68 (Electric Power Steering): N30/3 ESP: U071286, Steering column tube module control unit has a malfunction. There is an incorrect signal. N68 EPS: U042986, Implausible data were received from the steering column module. There is an incorrect signal. Please open a TIPS case to the Body/Chassis/Entertainment inbox.

192 Cause Increased quiescent current Remedy 1. Conduct quiescent current measurement. DO NOT USE A DVOM IN LINE - this will blow the fuse in your meter. Use an amp clamp with either a DVOM or XENTRY Scope and wait until the vehicle has gone to sleep (usually takes 6-10 minutes). Once the vehicle is asleep, observe the quiescent current for 10-15 minutes and note down the values. A stable quiescent current should be less than 50 mA. Values higher than this figure are considered not OK (NOK) and require further analysis. 2. If the quiescent current is higher (> 50 to 100 mA): Check whether software updates are available for relevant control units: Door control units (DMD (N69/1), DMP (N69/2), DMRL (N69/3), DMRR (N69/4)), EIS (N73/3), PTCU (N127), OHCM (N70), GW (N73/3*1) After installing the updates: measure the quiescent current again If the quiescent current is < 50 mA, the vehicle is OK If the quiescent current is between 50 and 100 mA, continue with step 5 If the quiescent current is between 100 and 200 mA, continue with step 3 If the quiescent current is between 200 mA and 1 A, continue with step 4 3. For no-load current values of 100 to 200 mA: Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. Disconnect door separation points (A-pillar connection) when the vehicle is asleep, starting with the driver's side Document the quiescent current value If there is no change: Disconnect the door separation point on the front passenger side and note down the value again If the quiescent current falls below 50 mA after the door separation point is opened, the respective outer door handle must be replaced If the quiescent current drops below 50mA, the draw has been addressed and the vehicle can be released If the quiescent current remains above 50mA after the relevant door handles have been successfully replaced, please create a TIPS case to the LV/HV inbox and retain the removed door handles for the time being If the quiescent current does not change after the door separation point is opened, please carry out step 5 4. For quiescent current values between 200 mA and 1 A: Important: Before pulling out F320 and F304, the tow-away protection and interior protection must be deactivated to prevent an alarm from triggering Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. Wait until the vehicle has gone to sleep Pull out the fuses one after the other, starting with F323 (PTCU CU/N127), and note down the quiescent current value Perform the same test one at a time if the value is still high for each additional fuse: F119 (PTCU CU/N127), F324 (EIS CU/N73/3), F305 (EIS CU/N73/3), F320 (OCP CU/N70), F304 (OCP CU/N70) If pulling out the fuse reduces the quiescent current to below 50 mA, replace the corresponding control unit. After replacing, please measure and assess the quiescent current again Please create a TIPS case for information purposes If the quiescent current remains unchanged after the fuses listed above are pulled out, please carry out step 5 5. If the quiescent current remains above 50 mA after all controls have been implemented: Create a TIPS case Document all the completed steps and measurement results Attach the XENTRY Scope trace of the draws that you have seen and identify where certain steps were taken. Attach the latest N73 and N73/3*1 CUL's If the quiescent current is higher than 1 A, the bus keep awake control unit should be identified via the EIS gateway

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

192 Cause Increased quiescent current Remedy 1. Conduct quiescent current measurement. DO NOT USE A DVOM IN LINE - this will blow the fuse in your meter. Use an amp clamp with either a DVOM or XENTRY Scope and wait until the vehicle has gone to sleep (usually takes 6-10 minutes). Once the vehicle is asleep, observe the quiescent current for 10-15 minutes and note down the values. A stable quiescent current should be less than 50 mA. Values higher than this figure are considered not OK (NOK) and require further analysis. 2. If the quiescent current is higher (> 50 to 100 mA): Check whether software updates are available for relevant control units: Door control units (DMD (N69/1), DMP (N69/2), DMRL (N69/3), DMRR (N69/4)), EIS (N73/3), PTCU (N127), OHCM (N70), GW (N73/3*1) After installing the updates: measure the quiescent current again If the quiescent current is < 50 mA, the vehicle is OK If the quiescent current is between 50 and 100 mA, continue with step 5 If the quiescent current is between 100 and 200 mA, continue with step 3 If the quiescent current is between 200 mA and 1 A, continue with step 4 3. For no-load current values of 100 to 200 mA: Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. Disconnect door separation points (A-pillar connection) when the vehicle is asleep, starting with the driver's side Document the quiescent current value If there is no change: Disconnect the door separation point on the front passenger side and note down the value again If the quiescent current falls below 50 mA after the door separation point is opened, the respective outer door handle must be replaced If the quiescent current remains low after the relevant door handles have been successfully replaced, please create a TIPS case to the LV/HV inbox and retain the removed door handles for the time being If the quiescent current does not change after the door separation point is opened, please carry out step 5 4. For quiescent current values between 200 mA and 1 A: Important: Before pulling out F320 and F304, the tow-away protection and interior protection must be deactivated to prevent an alarm from triggering Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. Wait until the vehicle has gone to sleep Pull out the fuses one after the other, starting with F323 (PTCU CU/N127), and note down the quiescent current value Perform the same test one at a time if the value is still high for each additional fuse: F119 (PTCU CU/N127), F324 (EIS CU/N73/3), F305 (EIS CU/N73/3), F320 (OCP CU/N70), F304 (OCP CU/N70) If pulling out the fuse reduces the quiescent current to below 50 mA, replace the corresponding control unit. After replacing, please measure and assess the quiescent current again Please create a TIPS case for information purposes If the quiescent current remains unchanged after the fuses listed above are pulled out, please carry out step 5 5. If the quiescent current remains above 50 mA after all controls have been implemented: Create a TIPS case Document all the completed steps and measurement results Attach the XENTRY Scope trace of the draws that you have seen and identify where certain steps were taken. Attach the latest N73 and N73/3*1 CUL's If the quiescent current is higher than 1 A, the bus keep awake control unit should be identified via the EIS gateway

192 Cause Increased quiescent current Remedy 1. Conduct quiescent current measurement. DO NOT USE A DVOM IN LINE - this will blow the fuse in your meter. Use an amp clamp with either a DVOM or XENTRY Scope and wait until the vehicle has gone to sleep (usually takes 6-10 minutes). Once the vehicle is asleep, observe the quiescent current for 10-15 minutes and note down the values. A stable quiescent current should be less than 50 mA. Values higher than this figure are considered not OK (NOK) and require further analysis. 2. If the quiescent current is higher (> 50 to 100 mA): Check whether software updates are available for relevant control units: Door control units (DMD (N69/1), DMP (N69/2), DMRL (N69/3), DMRR (N69/4)), EIS (N73/3), PTCU (N127), OHCM (N70), GW (N73/3*1) After installing the updates: measure the quiescent current again If the quiescent current is < 50 mA, the vehicle is OK If the quiescent current is between 50 and 100 mA, continue with step 5 If the quiescent current is between 100 and 200 mA, continue with step 3 If the quiescent current is between 200 mA and 1 A, continue with step 4 3. For no-load current values of 100 to 200 mA: Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. Disconnect door separation points (A-pillar connection) when the vehicle is asleep, starting with the driver's side Document the quiescent current value If there is no change: Disconnect the door separation point on the front passenger side and note down the value again If the quiescent current falls below 50 mA after the door separation point is opened, the respective outer door handle must be replaced If the quiescent current remains low after the relevant door handles have been successfully replaced, please create a TIPS case to the LV/HV inbox and retain the removed door handles for the time being If the quiescent current does not change after the door separation point is opened, please carry out step 5 4. For quiescent current values between 200 mA and 1 A: Important: Before pulling out F320 and F304, the tow-away protection and interior protection must be deactivated to prevent an alarm from triggering Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. Wait until the vehicle has gone to sleep Pull out the fuses one after the other, starting with F323 (PTCU CU/N127), and note down the quiescent current value Perform the same test one at a time if the value is still high for each additional fuse: F119 (PTCU CU/N127), F324 (EIS CU/N73/3), F305 (EIS CU/N73/3), F320 (OCP CU/N70), F304 (OCP CU/N70) If pulling out the fuse reduces the quiescent current to below 50 mA, it must be replaced. After replacing the fuse, please measure and assess the quiescent current again Please create a TIPS case for information purposes If the quiescent current remains unchanged after the fuses listed above are pulled out, please carry out step 5 5. If the quiescent current remains above 50 mA after all controls have been implemented: Create a TIPS case Document all the completed steps and measurement results Attach the XENTRY Scope trace of the draws that you have seen and identify where certain steps were taken. Attach the latest N73 and N73/3*1 CUL's If the quiescent current is higher than 1 A, the bus keep awake control unit should be identified via the EIS gateway

electronic ignition switch (EIS) control unit does not correspond to current production specifications. This OTA software update for the 12-V EIS will improve battery management and enhance the robustness of the vehicles electrical system. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

Electronic Ignition Lock control unit coding does not correspond to current series production configuration. As a result, battery management could be affected and cause low battery voltage. A 12V battery message may appear in the instrument cluster after the vehicle has been dormant for an extended period of time. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will SCN code the Electronic Ignition Lock control unit. The new SCN coding improves battery management, improving the efficiency of the 12V electrical system.

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: vehicle technical issue? customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: Amperage setting of charger and time battery was on charger XENTRY Battery Tester results Voltage of battery taken with multimeter: Do not connect charger while taking measurements N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) Workshop analysis of conspicuous data Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

High Voltage Battery (HVB) AC charger software does not correspond to current production specifications. As a consequence, a HVB MIL may illuminate during charging due to fluctuations in power consumption of the charging socket actuator. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the HVB AC Charger Software.

Battery Management System control unit software does not correspond to current production specifications. As a result, the battery Malfunction Indicator Lamp (MIL) may illuminate when no system fault occurs. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the Battery Management System control unit software.

To verify the supplier and software number of the steering column module. See attachment "Supplier Identification" for assistance. Cause MRSM/SCCM flashed to SW A2239028729 Remedy Please send VIN specific ID1 Support Package online using the XENTRY Kit used during the time the error occurred. Then, create an XSS ticket using the Support Tool icon under XENTRY Diagnosis.

CarPlay over Wi-Fi Audio cuts out Device not recognized No operation possible Cause There are multiple possible causes for an iPhone disconnecting from a vehicles head unit while using Apple CarPlay. These include hardware, software, and environmental factors: Environmental Interference External Sources: Passing under toll bridges, driving near airports, or areas with heavy electronic interference (e.g., as described in LI82.85-P-076157) can cause connection drops. Cellular Networks: Interference from nearby cell towers operating on similar frequencies (usually 2.4GHz or 5GHz) can disrupt the signal. Storage Location: Keeping your phone in a handbag or surrounded by other objects inside the vehicle can create physical or electronic interference. Device and Software Issues Head Unit Software/Hardware: Outdated firmware, bugs, or hardware faults in the vehicles head unit can prevent a stable connection. iPhone Software/Hardware: Similar issues in the iPhone, including buggy iOS updates or hardware problems, may affect performance. Reset or Reboot: Automatic rebooting or resetting of either the head unit or the iPhone will temporarily disrupt CarPlay. Connection and Settings Wired Connections: Faulty Cable: A damaged or poor-quality USB cable can cause intermittent or total loss of connection. USB Port Issues: Dust, debris, or physical damage in the USB port of either the head unit or the iPhone can also lead to disconnects. Wireless Connections: Intermittent Bluetooth/Wi-Fi: Unstable wireless communication (Bluetooth/Wi-Fi) can frequently break the Car- Play connection. Power Management: Battery Saver Mode: Enabling low power mode may restrict background processes, affecting CarPlay. Vehicles Electrical System: Unstable power delivery from the cars battery or electrical interruptions can cause the head unit to malfunction. Phone & App Configuration Phone Settings: Incorrect or conflicting settings (especially Bluetooth or Wi-Fi) on your iPhone can interfere with the CarPlay link. Third-Party Apps/Profiles: Installed apps or configuration profiles may conflict with CarPlays operation. Native apps are apple maps, apple music, audio books, apple news, podcasts, messages and phone. All other apps are considered third party apps. App Conflicts: Running conflicting apps that require similar system resources as CarPlay can cause instability. Mobile Data Plan: Streaming from online sources without sufficient mobile data can result in lost connectivity. Other Factors Heat & Overheating: If either the phone or the head unit overheats, they may disable certain functions to prevent damage, leading to disconnection. User Actions: Accidentally disconnecting the device in settings, or physically moving or bumping the phone or cable, may disrupt the connection. Remedy Guided Diagnostic Path for Apple CarPlay Connection Issues Please follow the steps below to systematically diagnose and resolve CarPlay concerns: Update Devices: Ensure the iPhone is updated to the latest available iOS version. Ensure the vehicles head unit is updated to the latest software version available. Isolate the Issue: Check whether the symptom persists with another iPhone running the latest iOS version. Test both wireless and wired CarPlay connections: Does the issue only occur with wireless CarPlay?

coding for the electronic ignition lock control unit does not correspond to the latest series production configuration. The electronic ignition lock control unit will be updated to change the logic for locking and unlocking the vehicle via the door handles. To unlock the vehicle, the large outer contact surface of the door handle must be touched. To lock the vehicle, the small, recessed contact surface of the door handle must be touched. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: vehicle technical issue? customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge, create a TIPS case. -Must include with the case: Amperage setting of charger and time battery was on charger XENTRY Battery Tester results Voltage of battery taken with multimeter: Do not connect charger while taking measurements N10/6 FSAM and N73/3 EZS CUL Workshop analysis of conspicuous data Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Test: Please perform the new SCN coding for HOSWD control unit (N179/1) (available since May 2025). Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> Please create TIPS case! If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no fault is visible: Please open a TIPS case! In the event of a customer complaint and further fault code in HOSWD: B1E7713: Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). B1F1F04: Check hand detection system control unit; if necessary swap with donor vehicle (ensure that the HW part numbers are identical).

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Test: Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Reset the HOSWD control unit in line with the guided test in Xentry. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> replace steering wheel rim. If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no defect is visible: Please do not replace the steering wheel, but wait for new coding parameters which should be available 05/2025. Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. B1E7713: Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is now available for Star 3 vehicles only. Fault in IDC223 control unit: U186B29: Delete fault memory and flash the new IDC (N62/4) software A223 902 75 37. If the software update is not available, or the problem persists, create a TIPS case. Fault in IDC213 control unit: U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the HOSWD control unit then scan the steering wheel and check whether the fault is reproducible. If reproducible: Create a TIPS case, adding the

Cause Temperature sensor in overhead control panel (OCP) delivering incorrect values: The temperature sensor in the overhead control panel is malfunctioning. Fault code B110709 or fault code B11F697 are present in the overhead control panel with the status (active) or (active stored). or The temperature sensor in the overhead control panel measures an incorrect temperature (the temperature value can be checked against the actual value in the overhead control panel) If the above-mentioned fault code is not present, the cause could be malfunction on the air conditioning system. Remedy If one of the above-mentioned fault codes should occur, a TIPS case must be created here. If the above fault codes or actual value differences are present in the OCP - please send the case to the Body/Chassis/ Entertainment inbox. Otherwise, the case must be sent to the HV/LV inbox for support in A/C diagnosis. *** It is not necessary to replace the overhead control panel ***

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10P067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

with one of the following scenarios: Flashing without a speed limit (" "). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. NOTE: Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Update head unit software to latest version and the recheck function in the same location. NOTE: Updated head unit software for AMG's has NOT been released yet. ETA 12/2026. If vehicle is still exhibiting one of the symptoms as described exactly as in the complaint section or as shown in the video attachments, open a TIPS case to the Body/Chassis/Entertainment inbox with the following: Video of the concern. Exact location (latitude and longitude is best)

with one of the following scenarios: Flashing without a speed limit (" "). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. NOTE: Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Update head unit software to latest version and the recheck function in the same location. If vehicle is still exhibiting one of the symptoms as described exactly as in the complaint section or as shown in the video attachments, open a TIPS case to the Body/Chassis/Entertainment inbox with the following: Video of the concern. Exact location (latitude and longitude is best)

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

a new software update for the MBUX Infotainment System. An OTA update will further enhance functionality and stability of the MBUX Infotainment System. This OTA update will include New DIGITAL LIGHT projections for opening/closing the vehicle doors, Apple iPhone notifications synchronization, and removal of online Metadata Enrichment (e.g. album cover pictures, composer information, and pictures of the artist). MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. NOTE: Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: The vehicle must be exhibiting the concern as shown in the attachment videos. The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. If the geographic location is known, it is very important that it is provided. Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q3 2026.

2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. The following applies to model series 167 from AEJ 22/1 onward, 192 AMG, 206, 214, 223, 232 AMG, 236, 254, 290 AMG from AEJ 23 onward, 294, 295, 296, 297 and 465: Reinitialize ASSYST Plus under Adaptations Teach-in processes ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.

when using flashing method ethernet to USB-C. Until further notice, please flash via VCI only.

2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations Teach-in processes ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.

2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations Teach-in processes ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. NOTE: Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q2 2026.

the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q4 2025 to early Q1 2026 to rectify concern.

the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q4 2025 to early Q1 2026 to rectify concern.

OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: Hitting the curb/posts with the front wheels. Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). Cracks (1) High pressure cleaner (2) Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

- The departure time, charging pause, location-based charging or target SOC limit is automatically set to 50% or to a random value in the Mercedes me application or in the charging settings on the head unit display. (Picture 1 & 3) - Incorrect notifications appear in the Mercedes me application for charging-related functions. (Picture 2) Related DTCs in quick test: No related fault codes (DTCs) are stored in the relevant control units. CPC3 - N127 (Drivetrain control unit) OBL223_GEN4 - N83/11 (Alternating current charger for high-voltage battery) DCB223 - N116/5 - Direct current charge connection unit (DCCU) Picture1 The target SOC limit is automatically set to 50% or any random values during charging. Picture 2 Incorrect notification Example Unable to unlock charging cable. Picture 3 Incorrect settings of charge interruption or pause. (If applicable) Cause - The Customer shares their Mercedes me credentials (password) with a third-party application, for example, a wall box application. This causes the Mercedes Benz backend server to receive random requests to reset the maximum SOC, departure time, charging pause, etc. - Charging settings are set incorrectly, for example, incorrect departure time, charging program, charging interruption/ pause, etc. Remedy The remedies below may vary depending on the customer complaint. Refer to the remedy that best matches the customer complaint. Remedy 1: The target SOC limit is automatically set to 50% or to random values during charging. - Change the Mercedes me login password on the Mercedes me homepage. (My Account > Login and Security > Reset). (Refer to Annex 1). Previously granted authorizations should then be revoked so that the charging settings can no longer be changed by external applications. Advise customers not to share the new password again. - Are there any sub-users? If yes, revoke their rights and reassess the function. -If differences between the vehicle and the Mercedes me app are visible, a new synchronization is recommended. Turn off Digital Extras through the Mercedes me app or the MMCR portal, and then turn the services on again. Remedy 2: Incorrect notifications in the Mercedes me app for charging-related functions. - Restart synchronization between the app and backend. Turn off Digital Extras through the Mercedes me app or the MMCR portal, and then turn the services on again. (Refer to Annex 2) Remedy 3: Incorrect charge interruption or pause setting. - Perform a factory reset of the head unit (A26/17). (Home > Functions > System > Reset), or turn off/correct all charging settings. (Refer to Annex 3) Additional Information: (Good to know) The LED on the charging inlet or socket indicates whether charging is completed or paused. 1) If the target SOC is reached, the charging inlet LED lights up Blue/Green without flashing. 2) If charging is paused, the charging inlet LED lights up orange without flashing. Additionally, the head unit charging settings display a charging pause. Note: Do not replace any hardware components for these complaints. If the complaint cannot be solved, please contact via TIPS or CAC.

236.17 due to a global supply constraint. 236.17 ATF 1L and 5L (PNs: A002989060312 and A002989060313) bottles are out of stock or in limited supply at Zep. This LI has been created with the following intention: - Provide dealers with additional workshop-focused guidance regarding the current ATF 236.17 supply constraint and the planned introduction of ATF 236.18. - Supplement existing communications and address common workshop questions related to maintenance, repairs, and fluid applicability. - Provide technical clarification and practical workshop guidance during the temporary supply constraint period. Dealers should continue to reference the latest News Channel Updates (NCUs) for the most current information regarding availability, ordering processes, supply status, and other related updates. Cause Damage to the Shell production facility has resulted in 236.17 oil supply being reduced to 50% of normal output until the end of 2026. Remedy Please first check Latest NCU updates for latest detailed information. Please continue placing orders through Paragon as normal. Supply is expected to remain reduced and allocation measures are currently in place. We ask for your patience through this restricted supply period. Most orders will be filled in the order in which they were received, as supply is replenished. Those dealers with zero inventory, and pending orders, will receive priority. We expect supply to be stabilized in September 2026. Approved Fluids: Only use transmission fluid from the approved list found on the Mercedes-Benz Operating Fluids website. Non-approved fluid will result in mechanical damage to the transmission and must be avoided. https://operatingfluids.mercedes-benz.com/sheet/236.17 Approved fluids can be claimed as follows if there is no Mercedes-Benz part number: Part # ATFSUB1L - TRANSMISSION FLUID 1 LITER ATFSUB5L - TRANSMISSION FLUID 5 LITER Dealerships with Zero Inventory AND Grounded Vehicles: If a vehicle is currently grounded for repair at your dealer due to no 236.17 inventory, we may be able to expedite your order. Please open a StarSupport ticket including the following information: (Parts Related Inquiry>National Accounts>Zep) LI document number Short explanation of repair needed for grounded vehicle Current days down of RO Maintenance and Service Interval Guidance Published maintenance intervals remain unchanged. Vehicles should continue to be maintained in accordance with the applicable maintenance schedule. This LI does not revise or extend any published maintenance interval requirements. If all required parts and materials are not available prior to scheduling or beginning a transmission service, dealers should consider postponing routine preventative transmission maintenance until the necessary parts become available. For vehicles that have not yet reached the applicable maintenance interval and do not exhibit transmission-related concerns, there is no need to recommend preventative transmission services prior to the scheduled maintenance interval. When evaluating whether routine transmission maintenance can be deferred until parts become available, dealers should consider: Overall vehicle condition Vehicle usage and operating conditions Presence of transmission-related symptoms or customer complaints Customer expectations and vehicle operating requirements Availability of required parts and materials Introduction of New Fluid Specification 236.18 Mercedes-Benz is currently preparing the introduction of ATF 236.18 as an additional approved transmission fluid solution for applicable NAG3 transmissions. At the time of publication of this LI, ATF 236.18 is not yet available for dealer ordering or workshop use in the U.S. market. See attachment for further details.

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

drivetrain control unit does not meet current production specifications. The system may experience an excessively high quiescent current draw on the vehicle, which could lead to an increased discharge of the 12V battery. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the drivetrain control unit software.

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465, 906 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174

drivetrain control unit does not meet current production specifications. The system may experience an excessively high quiescent current draw on the vehicle, which could lead to an increased discharge of the 12V battery. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the drivetrain control unit software.

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 23rd, 2026. After July 23rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, June 11, 2026. After June 11th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

The deadline for all dealer returns is no later than Thursday, June 4, 2026. After June 4th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

charging function does not correspond to the current series production configuration. The charging system software will be updated to stabilize the charging function of the vehicle. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

The updated software improves system stability and enhances the robustness of the driver assistance system. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

Cause The seat can be adjusted too far to the rear beyond the correct limit (combination of seat adjustment and seat backrest angle). Remedy Remedy SW A2329038302 for the SEAT control unit to limit the adjustment range of the mechanical seat components.

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not preauthorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Axle Half Shaft noise when changing direction - Front) LI33.30-P-056665 (Axle Half Shaft noise when changing direction - Rear) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

N51/1 - "The pressure control system has a malfunction. There is an implausible signal." C128864 in N51/1 - "The level control system has a malfunction. The duration of the actuation was exceeded: overload protection is active." Note: Only applies to vehicles up to production date October 15, 2025 Cause Coding in the suspension control unit N51/1 (EHRC232). Remedy SCN code the suspension control unit N51/1 (EHRC232). Verify no instrument cluster light illuminates when actuating the front axle lifter to the raised and lowered position.

Cause Many possible root causes Remedy *Note - This Li does not apply if there are other Li's that apply to your concern OR you have a fault and/or guided test that leads to a root cause. AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements (Template attached to be used for submission of Warranty claim and/or TIPS case) Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements Cooling Capacity Test (If System Has a Charge) Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs - Warranty Submission Requirements on the Repair Order Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found

Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

and play them with Windows Media Player. Cause Driving with summer tires in combination with low outside temperatures. At low outside temperatures or in wet conditions, a noise may be produced at the outer wheel on the front axle while maneuvering with sharp steering angles. Note: AMG vehicles with 4MATIC of model series 217 (without code 494) and model series 222 have a modified axle geometry compared with series production vehicles to provide more sporty handling. The problem cannot be remedied by changing the axle settings.

E61.0 Remedy In the IC Control Unit Log, please check the following information: Verify whether DTCs B228229, B228287, and B226656 are present in either A or A+S. Verify that Status SchlsselID = "ID is not valid" and Anlernstatus = "IC is initialized", as shown in the attached image (image_2). Please run the XENTRY guided test for the listed DTCs and provide the results.

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. Cause Under Investigation Remedy Under investigation. One option is to turn off Traffic Sign Assist until the investigation is completed. Once completed this LI will be updated. No TIPS case is necessary. Do not replace parts.

control unit software for the trunk lid control does not correspond to the current series status. The new software update stabilizes the automatic trunk lid opening height when automatically opened. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. Mercedes-Benz is continuously updating the operating system of its vehicles for a better customer experience.

Adjustment of the side window panes Adjustment of the doors Influence of seals Influence of assembly Remedy If the wind noises only occur on one side: Perform comparison of right/left of the window and door adjustment If necessary, correct window and door adjustment according to WIS. For the windows, observe the insertion depth in the Z position and the Y position on the mirror triangle in particular. Check inner seal for deformations. To do so, observe attachment 1 and attachment 2. If a deformation (waviness) can be ascertained: Replace seal or reform back into place using heat and fix in place using cold. Check outer sealing rail to vertical sealing lip of the mirror triangle. To do so, observe attachment 3. If the sealing rail collides with the vertical sealing lip of the mirror triangle: Either route it such that it rests above the vertical sealing lip of the mirror triangle or shorten. Check external sealing rail for correct assembly. To do this, ensure that it is engaged into the three existing mounting straps on the door. See Attachment 4. Also ensure that the outer sealing rail is correctly positioned in the x-direction and closes off flush. See Attachments 5 and 6 for this. Also ensure during assembly that the outer sealing rail is inserted beneath the mirror triangle. See Attachment 7. Check the inner seal, especially in the mirror triangle area, for correct assembly. See Attachment 8.

Replace no parts. Open a TIPS case and include: Initial quick test with freeze frame ME control unit log

Replace no parts. Open a TIPS case and include: Initial quick test with freeze frame ME control unit log

Based on technician feedback, the OTA (code: 25P5496529) does not start even after an extended period of time and several driving cycles. In addition, the "Continue" button is grayed out. Cause The exact cause for the OTA not to start is currently under analysis. Remedy Please check whether the vehicle is affected by the field measure "Update software of Supplemental Restraint System (SRS) control unit" (code: 25P5496529) and if yes, perform this update using a XENTRY with all latest Add-Ons and bill under accounting number 5496529. If the vehicle is not affected by this field measure, in the event of a complaint update control unit ORC223 (N2/5 -Supplemental Restraint System SRS) using XENTRY and use damage code 8251M01. As of XENTRY Release Version 06/25, control unit ORC223 can also be updated in this context without a password. Provided control unit ORC223 is error-free after the update, the vehicle can be handed back. ***IMPORTANT*** -In isolated cases, the OTA update may continue to be displayed for up to 3-4 weeks even after flashing with XENTRY. Note: This LI applies only to the OTA update for occupant protection!

Based on technician feedback, the OTA (code: 25P5496529) does not start even after an extended period of time and several driving cycles. In addition, the "Continue" button is grayed out. Cause The exact cause for the OTA not to start is currently under analysis. Remedy Please check whether the vehicle is affected by the field measure "Update software of Supplemental Restraint System (SRS) control unit" (code: 25P5496529) and if yes, perform this update using a XENTRY with all latest Add-Ons and bill under accounting number 5496529. If the vehicle is not affected by this field measure, in the event of a complaint update control unit ORC223 using XENTRY and use damage code 8251M01. As of XENTRY Release Version 06/25, control unit ORC223 can also be updated in this context without a password. Provided control unit ORC223 is error-free after the update, the vehicle can be handed back. ***IMPORTANT*** -In isolated cases, the OTA update may continue to be displayed for up to 3-4 weeks even after flashing with XENTRY. Note: This LI applies only to the OTA update for occupant protection!

a new software release for the MBUX Infotainment system. An OTA update will enhance both functionality and entertainment features. The update introduces Dolby Atmos support for in-car apps, improvements to the MBUX calendar app, and the launch of MBUX SOUND DRIVE. To deliver a better music streaming experience, new apps will be installed and existing integrations with online streaming providers will be removed. Each provider will now require a separate app, which will be installed during the update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.