2023 Mercedes-Benz AMG GLE63 TSBs

It will also ensure that if a case is necessary, all supporting documentation is available. This should not be used on its own as justification for creating a TIPS case. Cause The root cause will vary depending on the complaint. The goal of this document is to provide diagnostic checks and procedures that may help resolve customer complaints without opening a TIPS case. Remedy Before opening a transmission-related TIPS case, the following steps must be performed to ensure all relevant data has been collected and possible remedies (when applicable) have been performed. Please Note: At minimum, the documents below must be collected before proceeding to ensure the data in its original state when the vehicle arrived is captured. - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - Initial EEPROM data (.txt format) - IPR Result (if applicable. See LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool) - Transmission Heath Page If the vehicle has previously been repaired for the same concern, note the date, mileage, and TIPS case or RO number, along with a brief description of the prior work performed. IPR Guidance: The IPR recommended repair should be completed prior to following any steps in this LI and prior to case creation. IPR repairs do not require additional warranty approvals or a TIPS case to validate/confirm the results. To ensure efficient case handling, please avoid opening TIPS cases for this reason. For further information regarding IPR please see the following documents: LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool Oil Pan Condition Evaluation: In some situations, IPR will advise checking the oil pan condition and determining a repair based on the evaluation. Example photos in Xentry can be found in two ways: Use the blue hyperlink in the IPR result, and it will take you to the Condition check of transmission oil Navigate to Xentry Bluebook > Help for control unit > Condition check of transmission oil If a different repair that what is recommended by IPR is performed, attaching photo documentation of the complaint vehicle oil pan and the IPR example to the claim is required. Reproducing the Concern: Proper evaluation of transmission concerns generally requires the condition to be reproducible. It is recommended to compare the vehicle to a similar model, if available, to help determine whether the shift behavior is characteristic of the drivetrain or uncharacteristic for the vehicle. If the concern cannot be duplicated: A test drive with the customer may assist in understanding and reproducing the complaint. The vehicle shift quality should be compared to a known-good vehicle with identical drivetrain and model year. Check Shift Quality History (VGS Control Unit > Adaptations > Shift Quality History) Shift Quality History will show the last 5 noticeable harsh shifts and some of the parameters in which it occurred. You can use this to attempt recreation of the operating conditions and increase likelihood of reproducing the complaint. Complaint A: Shift Quality Note: Certain AMG variants may exhibit more firm and noticeable shift behavior as a normal characteristic. Refer to LI27.60P075147 for additional information. 1. Perform Valve flushing procedure 2. Perform 5 Torque Converter adaptions in a row - Allow the vehicle to warm up naturally, DO NOT power brake as it will increase the temperature in the torque converter. - After the 5th adaptation, collect a screen shot showing all 5 on one page 3. Perform a standstill adaption - collect a screen shot Recheck vehicle operation. If the concern has not improved, driving adaptations should be performed to target specific gear shifts.

In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (MIL).

Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

Cause Incorrectly installed (rotated) rotational speed sensors on the EHS (VGS Control Unit) can cause abnormalities in signals. As a result, poor adaptation values are stored and harsh gearshifts are felt. This only affects vehicles with VGS control units produced between days 182-296 of 2025 (July 4, 2025-October 23, 2025). Remedy 1. Collect initial transmission EEPROM file 2. Check EEPROM .txt file for VGS control unit serial number and production date (attachment figure 1) - If the valve body is already removed, you can inspect the control unit for its stamped serial number (attachment figure 2) If the production date is or is within 25182-25296 (07/4/25-10/23/25): The complete valve body will require replacement. 1. Remove transmission oil pan & inspect fluid/pan/filter condition - compare findings to extended fluid condition examples provided in Xentry blue book under general information for VGS 2. Replace complete EHS valve body, fill to near max fluid level, & complete initial start-up - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement. (See photos in WIS instructions) - Verify the new valve body production date is outside of day 182-296 of 2025 (attachment figure 2) If the production date is outside of this range: This LI is not applicable. 1. Perform IPR and follow recommended instruction

engine control unit software does not correspond to current production specifications. As a consequence, the functionality of the post-catalyst oxygen sensor may be impaired due to increased thermal loading. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.

Vehicle has one or more DTC's Present P164B00, P164B09, P2B4400, P005A07, P005C07, P005A09, P005C09, P003C07, P2B5007, P003C09, P2B5009, P34C200, P34C109, P34C800, P34BE00, P34BD09 Cause Software and Hardware Remedy 1. Check for available Software updates for the Engine Control Unit ME N3/10. Perform update if available. 2. Check part numbers on ALL CAMTRONIC actuators to ensure latest part numbers are installed. 3. A177 982 03 03 and A177 982 17 00 should be replaced by A177 982 19 00 4. A177 982 02 03 and A177 982 16 00 should be replaced by A177 982 18 00 5. Remove engine cover and check for heat damage on the engine cover and wiring harness in the area above the engine compartment bulkhead and near the windshield. 6. In the event of wiring harness damage please open a TIPS case with photos of the harness and include a Lambda Line Graph Test for evaluation.

the vehicle is stationary and ECO Start/Stop is active (combustion engine is off). The noise is more noticeable outside the vehicle and in acoustically shielded areas such as closed rooms or garages. Cause The noise in the valve body (EHS) is caused by superimposed pressure peaks acting on the valves. This phenomenon occurs only after a certain running-in period due to the influence of micro-contamination in the valve bores. Remedy A hardware modification of the electro-hydraulic control unit (EHS) is currently being implemented (no change to the part number). This will be incorporated into series production and as a spare part starting from 12/2025. This is only a comfort-related complaint and has no impact on the functionality or service life of the transmission. For sensitive customers, the following measures can be performed: 1. Replace the electro-hydraulic control unit (EHS), the oil pan, and the transmission fluid. - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement. (See attached location guide)

EEPROM or Transmission Health system following the replacement of the below components: - The electrohydraulic control unit (EHS valve body) in transmission 725.0/725.1 - The repair kit for the control unit (VGS) in transmission 725.0 Cause Missing, incorrectly installed, or damaged guide tubes on the EHS valve body. Remedy Check for the correct installation of the guide tubes (refer to attachments under Cause), correct installation if necessary. Parts Catalog References: NAG3M 725.1 AND NAG3C 725.0 (AMG only): Part numbers 100, 120, 150, 160 NAG3C 725.0 (Non AMG): Part numbers 280, 290, 330, 340 NOTE: If any of these guide tubes are not installed and the vehicle is driven, it will create several rinse and slipping events in the EEPROM data. These values caused by incorrect installation need to be erased to prevent future misdiagnosis. Submit a TIPS case to the Powertrain inbox with the following to receive the necessary reset password: - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - IPR Result - Initial EEPROM data (before repairs) - Latest EEPROM data - Photo of oil level ultrasonic measurement next to XENTRY specifications Please provide detail regarding the reasoning for the initial replacement in your workshop findings and measures performed. (This topic was covered in the July 2022 and July 2024 Passenger Car Tech Topics)

This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications - Collect an oil sample of the original fluid 5. Complete all transfer case Tech-in processes located under VG Control Unit > Adaptations - Resetting the oil service data - Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature ( >60C ) 6. Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right 7. Perform an extended 200mi road test to ensure the clutches are properly conditioned with the new oil. 8. Reassess the concern and release the vehicle if no longer present. If the concern continues to occur with the control unit disconnected or after the above steps have been performed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial quick test with fault freeze frame data - Initial transmission EEPROM data - VGS and Transfer Case Control Unit Log (N45 or N15/7) - Photo of the original oil condition - What color was the fluid drained from the transfer case before the oil change? - Was an oil sample collected, and can you provide a photo of the original fluid? - What color and part number fluid was used during the oil change? - How far was the vehicle driven after?

release A 000 902 50 48 to software release A 000 902 15 89, the fault code B183319 may be output. B183319 "The battery for the 48V on-board electrical system has a malfunction. The limit value for current has been exceeded" Cause Anomaly in the software update Remedy Please perform the following steps in the specified sequence: 1.) Delete fault codes 2.) Disconnect XENTRY Diagnosis and the 12 V battery charger 3.) Disconnect ground cable from the 12 V battery 4.) Ensure bus idle for at least 10 minutes 5.) Re-connect ground cable to the 12 V battery 6.) Delete fault codes again 7.) Perform a test drive 8.) Check fault codes > If fault code B183319 is still current, continue with the guided fault analysis in XENTRY Diagnosis. > If fault code B183319 goes to stored and can be cleared, no further action is required.

Oil discoloration is present during oil change (water in oil) 3. Oil leakage from the breather cap Cause The bleed line of rear differential may be misaligned, causing the rubber end pieced to rest on the wheel well liner. When driving in the rain, water enters through the rubber elbow from the soaked wheel well liner. Remedy Perform a road test and determine the location of the noise using NVH equipment. If the rear axle differential is the root cause of the noise, continue with the following: 1. Drain oil from rear axle differential and check for signs of water intrusion (discoloration/cloudiness) Remedy A: If no water is found 2. Remove/install left wheel well trim. 3. Remove rubber end piece from the bleed line. 4. Install modified end piece with the part number A 167 351 50 00. 5. Identify source of the noise and, if necessary, replace the parts causing the concern. Remedy B: If water is found 2. Remove/install left wheel well trim. 3. Remove rubber end piece from the bleed line. 4. Install modified end piece with the part number A 167 351 50 00. 5. Replace rear axle differential

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". 5. Apply heat-resistant lubricating paste to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 6. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. e) Finally drive approx. 3 miles to allow the system to cool. f) Reassess noise.

clattering) can be heard underneath the bench seat, particularly in the case of a full tank (1/1 fill level). Cause The vibrating air column of the purge flow volume triggers the fill limit vent valve (FLVV) to open and close repeatedly when the fuel tank is full. Remedy By reducing the fuel quantity by around 5 liters, the noise can no longer be heard. In isolated cases, the noise can also be amplified by a fuel tank installed under stress and therefore lines adjacent to the body-in-white (above the fuel tank). In this case, the installation position of the fuel tank and the contact surfaces to the body-in-white must be checked. To do so, loosen the fuel tank and refasten it. Please do not replace component parts such as the fuel tank, activated charcoal canister, purge valve or delivery module, as this does not provide a remedy. If a similar noise can be heard with a tank fill level of, for example, 3/4 or 1/4 and not with a full tank (1/1), there is a different issue.

Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Do NOT remove the expansion valve from the evaporator prior to being advised to in a TIPS case. 2. Initial Quick Test 3. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 4. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 5. OBS recording of XENTRY AC actual values of compressor request to be on and current value (Instructions in Attachments) 6. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 7. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 8. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 9. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments.

- Current and saved fault code in DCCU and powertrain control unit (PTCU): P2E9873 The position sensor of the external socket flap of the vehicle socket (direct current) indicates an electrical fault. The actuator does not open. - The vehicle starts or charges normally and without any problems. Cause Software in the control unit "N116/5 - DC charge-connection unit (DCCU)". Remedy For model series 167 (Only for USA): Remedy is available: Update software for N116/5 (DC charging control unit box) and perform SCN coding of N116/5. Once the SCN coding has been updated, the engine diagnosis indicator lamp (MIL) is no longer actuated with this fault code. For other model series: Work on the SW remedy for N116/5 (DC charging control unit box) is in progress. Once the software is available, update the software for N116/5 and perform SCN coding of N116/5. If this problem occurs, the vehicle start or charging functions are normally not affected; therefore do not replace any parts. Replacing parts does not solve this problem.

eight-cylinder engine, the sealing ring in the engine thermostat could detach, causing a delay in the heating of the engine coolant. This may also cause the check engine Malfunction Indicator Lamp ('MIL') to illuminate.

In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the engine thermostat (including software update) installed in certain Model Year (MY) vehicles (with engines M176, M177, M178) listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first), due to the following condition In the affected vehicles, the sealing ring in the engine thermostat could detach, causing a delay in the heating of the engine coolant. This may also cause the check engine Malfunction Indicator Lamp (MIL) to illuminate.

Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it and then continue with1b. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: NOTE: If brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise.

Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise.

Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Do NOT remove the expansion valve from the evaporator prior to being advised to in a TIPS case. 2. Initial Quick Test 3. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 4. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 5. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 6. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 7. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 8. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 9. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments.

Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. Please see the list of WIS documents for forming gas leak check and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. Ensure that a full vacuum is pulled on the system for at least 30 minutes after replacement Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available.

platform), E-Class (213 and 238 platform), GLE (167 platform), and AMG GT 4-Door (290 platform) vehicles, the engine control unit software does not correspond to current production specifications. As a consequence, the functionality of the post-catalyst oxygen sensor may be impaired due to increased thermal loading. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures and open a TIPS case labeled "167 Evaporator Suspected of Leaking" In the case, please include the following: 1. Attach the Initial Quick Test 2. Short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (s 5. Video recording of the leak being found via sniffer and location. Note - Please see the list of WIS documents for forming gas leak check, AC flushing and recharging of the system. The dryer must be replaced when there is a leak in the AC system.

can also be felt at the steering wheel. Particularly when braking or accelerating Stick/slip effect in sliding piece of steering coupling. Replace steering coupling.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10P067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

attachment) Head-up display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus (see attachment) Cause Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC) Remedy Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC) is now available. Please update both control units. TIPS cases are no longer needed. Note that issues may still occur even after the software updates. Please do not replace any parts. We will inform you as soon as a solution is available. Note: Please do not replace any parts for this complaint. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

REAR COMFORT PACKAGE (P08), the rear seat heating cannot be activated via voice control. However, the voice control erroneously provides feedback that the seat heating has been activated. Cause A26/17 - MBUX multimedia system (Head unit) software Remedy Software E604 (FUP6) corrects the erroneous feedback from the head unit regarding the activation of the seat heating. Important note: The feature "Activation of seat heating via voice control" is only available in vehicles with codes REAR SEAT ENTERTAINMENT (854/447/864) and 903 REAR COMFORT SEAT HEATING (903) or REAR COMFORT PACKAGE (P08) Availability: Software FUP6 is planned to be released in Q4 2025. Note: Please do not replace any parts for this concern.

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Head unit software variant. Remedy For all chassis use Xentry to update head unit (A26/17). Target boot software number should be either: 247 904 6600 (E905.4) OR 247 904 7500 (E906.1) If vehicle fits all criteria and either target software is not available via Xentry, please open an XSS ticket. Damage code 5424x-01 may be used with a repair start date after June 2nd, 2025.

REAR COMFORT PACKAGE (P08), the rear seat heating cannot be activated via voice control. However, the voice control erroneously provides feedback that the seat heating has been activated. Cause A26/17 - MBUX multimedia system (Head unit) software Remedy Software E604 (FUP6) corrects the erroneous feedback from the head unit regarding the activation of the seat heating. Important note: The feature "Activation of seat heating via voice control" is only available in vehicles with codes REAR SEAT ENTERTAINMENT (854/447/864) and 903 REAR COMFORT SEAT HEATING (903) or REAR COMFORT PACKAGE (P08)

multifunction display of the instrument cluster while driving (see picture in attachment). Cause On vehicles with HERMES 3.0 currently, A2389015700 A2389015800 A2389018400 A2389018900 A2389019000 A2389019800 A2579011200 A2579012100 The above-mentioned message is sporadically displayed in the instrument cluster once Remedy Please manually commission the control unit N112/9 (HERMES) using XENTRY: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit" Invoice the required work using damage code 8251M/01 (damage location/damage type).

attachment) Head-up display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus (see attachment) Cause Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC) Remedy control units. If symptoms persist after the software update, please fill out the attached questionnaire and open a TIPS case. Note: Please do not replace any parts for this complaint.

Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy Update of head unit A26/17 to the new software: FUP5 opt. E505.4 (A 297 904 05 01)

AMG GT, EQE, EQS, G-CLASS, GLB, GLC, GLE, GLS, S-CLASS, AMG SL (206, 118, 243, 290, 192, 294, 295, 296, 297, 465, 247, 254, 167, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.

Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy The remedy is currently being developed. Note: A remedy is not yet available. Replacing the hardware does not resolve the symptom. Do not replace the MBUX for this concern. The information will be updated accordingly as soon as a remedy is available.

display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus Cause Previous N133/1 - Instrument cluster (IC) control unit software. Remedy Update the N133/1 - Instrument cluster (IC) software.

"Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. Routine change in software in instrument cluster N133/1. Vehicle handover has not taken place. First manually commission the already installed instrument cluster control unit N133/1 and then perform the special procedure to re-initialize ASSYST data in powertrain control unit N127. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

EQE, EQS, GLC, GLE, GLS, S-Class, SL (206, 294, 295, 296, 297, 254, 167, 223, 232 platform) vehicles, the MBUX System software does not correspond with the latest series production configuration. The MBUX control unit will receive an OTA update that includes functional improvements and new features such as: Dolby Atmos, video streaming, personalized images on the front passenger display, and additional commands for the MBUX Voice Assistant. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

See attached picture for example. Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module NOTE: Occasionally to verify complaint, the steering column/vehicle needs to be in direct sunlight or hot conditions for a few hours. If noise only occurs when adjusting the steering column via electric actuation, please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on all pivot points including, but not limited to, green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, wipe excess grease off and perform greasing and movement to limit stops in all directions again. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. Include detailed items of the following: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

U013281 - Communication with control unit "Suspension" has a malfunction. Incorrect data were received. C156F00 - The signal values of the level sensors are implausible. Cause Physical layer wiring to the level control sensors B22/X. Remedy Check A108/2 and A108/3 for freeze frame data section "ZF_error_handler". The text will provide a good place to start. Example: "SPC_FEHLER_VehLvl_Stat_HP_AMG_AR2_SNA_VehLvl_RR_V2_AMG" indicates the Right Rear may have initiated the DTC. See attached picture for reference. Is concern reproducible? If so, watch actual values in Xentry and see which sensor is setting the implausible value. Use Hioki to measure wiring to all four level sensors from N51/8. Use above DTC freeze frame data to physically inspect specific wiring as mentioned in the freeze frame data above. Check all level sensors for damage, correct mounting, level sensors bound or not moving, etc... If vehicle exhibits concern after all of the above is completed, please open a TIPS case to the Body, Chassis, Entertainment Inbox.

our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage detection (DMTL) on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership.

communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

control units FSCM_GEN4/5/6 For these fault codes, the tests contained in XENTRY must be carried out P046109 / P206609 / P13E600 For these fault codes, the connector couplings/wiring harness routing must be checked for damage P206600 / P046100 Cause Various Remedy Carry out XENTRY tests for the listed fault codes in the FSCM (N118) and document the monitor graphics for the primary/ secondary lever-type sensors.

We hope that you're enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air ("OTA") Service Campaign to update the communication module software on certain Model Year 2019-2025 A-Class, C-Class, CLA, CLE, CLS, E-Class, EQB, EOE, EQS, G-Class, GLA, GLB, GLC, GLE/GLS, AMG GT 4-Door, and S-Class vehicles. This update includes quality-enhancing optimizations and product improvements.

Please note that if the complaint "Fuel filler flap not opening" occurs, it is important to check the fuel filler flap before replacing the central locking actuator. For gasoline hybrid vehicles where the fuel filler flap fails to open or does so but slowly, observe the document "Fuel filler flap fails to open or does so but slowly on plug-in HYBRID gasoline vehicles"! Cause Central locking actuator may have an electrical fault and may not open. Remedy 1. Car locked: To rule out incorrect operation, operate the fuel filler flap in the area shown in Fig. 1 and listen out for the clicking noise of the microswitch in the central locking actuator. If no clicking can be heard, continue with point 4. 2. Car unlocked: Press area on flap to start the microswitch clicking. Flap opens - show the customer the area to press. 3. Car unlocked: Flap cannot be opened regardless of which area you press. Open the flap by operating the emergency release for the CL actuator (through trunk, fender gap cover, etc, depending on specific vehicle) 4. Central locking actuator pressed directly, no clicking of microswitch, no electrical release of central locking actuator => Clicking of microswitch, electrical release of central locking actuator => Tank filler recess/charging recess not OK; report results via a TIPS case to B/C/E Inbox. 5. Replace central locking actuator; check function of new part before installing it: Do not dispose of damaged part. New central locking actuator does not release: More detailed examination of connector coupling, wiring harness, electrics required.

and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.

This complaint only occurs when "voice amplification" is active. Coupling noise of microphone signal in voice amplification. Intermediate remedy: The interference noise can be remedied by deactivating voice amplification: "Home" -> "Settings" -> "System" -> "Audio" and de-select "Voice amplification to rear" to switch off the function (see attachment). Note: To activate or deactivate the function, the ignition must be switched on, seat belts (at rear and front) must be fitted and the doors, windows and roof must be closed. Permanent solution: Perform software update of MBUX multimedia system (A26/17) to E419.5 (available from 06/19) or greater. Deactivate the voice amplification feature. Inform customer of function and effects of additional sounds caused by driving over bumps or uneven road surfaces.

2. Update left rear seat control unit software. - To do this, select menu item "Quick test view N32/5 Left rear electrical seat adjustment Adaptations Update of control unit software". - Then follow the user guidance in XENTRY Diagnosis. 3. Update right rear seat control unit software. - To do this, select menu item "Quick test view N32/6 Right rear electrical seat adjustment Adaptations Update of control unit software". - Then follow the user guidance in XENTRY Diagnosis. 4. Disconnect XENTRY Diagnosis.

Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button

C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.

A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.

and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case - Open a TIPS case for vehicles: As of manufacturing date 01.02.2022, except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa As of manufacturing date 01.08.2022 and production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] 3. Remedy for vehicles prior to manufacturing date 01.02.2022 (except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) or 01.08.2022 (production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.

Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!

steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.

C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

(see attachment). Cause The cause is currently being investigated. Remedy Update the HU7 to the latest software version, then perform a factory reset of the HU7. Steps to perform factory reset: Navigate to Settings > System > Reset > Reset to factory settings and confirm. If the problem persists, please record HU7 log and also a trace of the Body CAN (For Star 2 Body Can 1 and for Star 3 Body Can 2) during the symptom and send via a TIPS case to the Telematics team. Note: Only collect and submit the log and trace if the symptom can be reliably reproduced.

Cause Incorrect replacement wiper blades may have been installed A167 820 92 01 may have been installed instead of A167 820 87 03. After longer periods of non-use, the wiper blade lip may compress slightly and result in streaking. Only vehicles built before October 20th, 2022 should use wiper A167 820 92 01. Remedy Install the correct part number for the replacement wiper blades.

Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.

E-Class, EQE, EQS, GLC, GLE, GLS, GT, S-Class, and SL vehicles (205, 206, 236, 213, 214, 238, 294, 295, 296, 297, 253, 167, 290, 223, 232 platform), the tire sealant bottle may not meet specifications. The possibility exists that the tire sealant bottle may leak within the installation location. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk.

(167 platform) vehicles, corrosion on the solenoid may occur in the electric coolant pump. In this scenario, a yellow coolant warning lamp may be shown in the instrument cluster. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will inspect the electric coolant pump and replace it, if necessary.

NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not preauthorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Vehicle production date prior to December 2025. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify.

vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions. These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. (Extract from the owner's manual) If customer complaints are received, please proceed as follows: Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it Check whether the complaint can be reproduced and at which axle the noises occur (ideally together with the customer while driving) Check the friction pairings of the affected axle for wear, mechanical damage or localized overheating damage. a) If this is the case, replace the damaged component parts and assess the brake again with regard to noise. b) If there no obvious visible or technical problems with the brake system, we recommend bedding in the brakes by following the procedure below: Before trip, the mileage incurred must be clarified with the customer (approx. 50 km) Select a suitable route Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 100 km/h to 50 km/h (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1.5 km between brake applications Finally drive approx. 5 km to allow the system to cool Reassess the problem If this action fails to deliver the desired success, create a TIPS case with the following information: Observe SI00.00-P-0086A Have parts already been replaced? If yes, when and which parts (date, mileage)? How is the customer's driving profile, and when/where is it reproducible? Create a video/ sound file Attach usable pictures of the brake components on the affected axle (important: including the back of the lining)

If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document. Conditions Instrument Cluster Message: "Park Assist Inoperative" and Hardware part numbers: A0009019716 or A0009016022 B223263 with Bosch-ID C259; A+S (Active and Stored) and B223255 with Bosch-ID 1B5D; A+S (Active and Stored) Notes: Other DTC's are permitted but the above three conditions must be met. If they are not met, this LI is not applicable. See attachment "LI Criteria" for an example. Attachment portrays a quick test with non-matching criteria and therefore does not require a TIPS case. Cause Under analysis. Remedy Please do not make any attempts to repair the park control unit. Do not flash or SCN code. Open a TIPS case.

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. Cause Under Investigation Remedy Under investigation. One option is to turn off Traffic Sign Assist until the investigation is completed. Once completed this LI will be updated. No TIPS case is necessary. Do not replace parts.

If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document. Conditions Instrument Cluster Message: "Park Assist Inoperative" and Hardware part numbers: A0009019716 or A0009016022 B223263 with Bosch-ID C259; A+S (Active and Stored) and B223255 with Bosch-ID 1B5D; A+S (Active and Stored) Notes: Other DTC's are permitted but the above three conditions must be met. If they are not met, this LI is not applicable. See attachment "LI Criteria" for an example. Attachment portrays a quick test with non-matching criteria and therefore does not require a TIPS case. Cause Under analysis. Remedy Please do not make any attempts to repair the park control unit. Do not flash or SCN code. Open a TIPS case.

If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document. Conditions Instrument Cluster Message: "Park Assist Inoperative" and B223263 with Bosch-ID C259; A+S (Active and Stored) and B223255 with Bosch-ID 1B5D; A+S (Active and Stored) Notes: Other DTC's are permitted but the above three conditions must be met. If they are not met, this LI is not applicable. See attachment "LI Criteria" for an example. Attachment portrays a quick test with non-matching criteria and therefore does not require a TIPS case. Cause Under analysis. Remedy Please do not make any attempts to repair the park control unit. Do not flash or SCN code. Open a TIPS case.

If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document. Conditions Instrument Cluster Message: "Park Assist Inoperative" and B223263 with Bosch-ID C259; A+S (Active and Stored) and B223255 with Bosch-ID 1B5D; A+S (Active and Stored) Notes: Other DTC's are permitted but the above three conditions must be met. See Attachment for an example of Bosch ID location. Attachment portrays a quick test with non-matching criteria and therefore does not require a TIPS case. Cause Under analysis. Remedy Please do not make any attempts to repair the park control unit. Do not flash or SCN code. Open a TIPS case.

The deadline for all dealer returns is no later than Thursday, June 4, 2026. After June 4th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

EQE, EQS, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (118, 167, 192, 206, 223, 232, 243, 247, 254, 290, 294, 295, 296 and 297 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for a better entertainment experience. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

The clunk is heard once when changing from forward to reverse (and vice versa). Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Vehicle VIN is one of the following: 4JGFB6BB5SB390103 4JGFD6BB1SB391761 4JGFB6BB4SB391033 4JGFD8KB6SB392142 4JGFD8KBXSB392127 4JGFB8KB1SB390739 4JGFD6BB7SB390047 4JGFD6BB6SB390475 4JGFB8KB9SB391413 4JGFD6BB6SB390296 4JGFB6BB2SB390740 4JGFD6BB4SB392399 4JGFD6BB5SB390077 4JGFD6BB2SB390893 4JGFD6BB1SB391999 4JGFD6BB3SB391325 NOTE: If VIN is outside of range, LI is NOT applicable. Cause Strut length not to specification. Remedy Replace front left and right strut. There is no drivability concern, only vehicle comfort.

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Cause A26/17 - MBUX multimedia system (head unit) software Remedy Update the A26/17 - MBUX multimedia system (head unit) to newest/latest software. Then recommission steering wheel electronics N135 - steering wheel electronics (LRE). If the problem is still present, please create a TIPS case. Note: Please do not replace any parts.

cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.

Cause Many possible root causes Remedy *Note - This Li does not apply if there are other Li's that apply to your concern OR you have a fault and/or guided test that leads to a root cause. AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements (Template attached to be used for submission of Warranty claim and/or TIPS case) Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.

Cause Under analysis. Remedy Neither of the two event codes is relevant for the functioning of control unit IDC213 - N62/4 (Intelligent Drive control unit) and can be ignored.

periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!