2025 Mercedes-Benz AMG GLE53 4Matic+ Coupe TSBs

and 725.1 (NAG3 facelift/9GTRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the ongoing quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 Classic AMG sport model (AMG 43 and AMG 53 with converter, automatic transmission 725.0) NAG3 Classic Hybrid (automatic transmission 725.0) NAG3 Classic AMG 63 (automatic transmission 725.0) NAG3 MOPF ISG2 (automatic transmission 725.1) NAG3 MOPF Hybrid (automatic transmission 725.1) NAG3 MOPF AMG sport model (AMG 53/AMG 53e with ISG48V2 & converter /hybrid, automatic transmission 725.1) NAG3 MOPF AMG 43/63 with engine 139/177 (automatic transmission 725.1) Steps for the Service Advisor: Important: The more information and detail that can be given to the workshop about the complaint, then the more effective the subsequent diagnosis with IPR can be. To this end, a detailed service reception questionnaire has been provided to help the Service Advisor ask the right questions about the complaint. Ask precise details about the customer complaint and the conditions and context. Fill out the service reception questionnaire (please see WIS document: OF27.00P300005A) for customer complaints in detail and forward it to the workshop. Operation steps for the workshop employee: 1. Perform quick test 2. Access the transmission control unit via XENTRY Diagnosis 3. Select "A customer complaint has been received" and carry out all subsequent operation steps (IPR diagnosis path). 4. The IPR repair instructions are displayed, Carry out the IPR repair instructions without performing any further diagnostic or repair steps. Important: The IPR repair instructions are binding and must be carried out. Differing repairs are possible; such repairs must be documented in XENTRY in free text. Please observe the information regarding the IPR diagnosis process in XENTRY. Conventional diagnosis and subsequent appropriate repairs are only permitted if IPR does not specify any repair instructions. Invoicing for the guided IPR steps: Operation item 270640 and 0.1 hours Notice regarding warranty: The use of IPR in association with warranty claims is mandatory! If the IPR repair instructions are disregarded without justification, the warranty claims may be rejected and/or are subject to debit. IPR will provide a measure to repair the vehicle based on various data sources (EEPROM, fault codes, etc). Please consider the vehicle maintenance record of the vehicle. For warranty and goodwill repairs, the transmission ECU test log and/or IPR test result must be uploaded into Paperless XENTRY Diagnosis (pXD) . If repair is being determined based of oil pan condition pictures of oil pan MUST be provided to warranty as justification. Tamperproof documentation: The IPR repair instructions are stored in the control unit log. Please file this document in a tamperproof manner either in digital form or as a hardcopy printout and also enclose a printout with the damaged part. In this regard, please comply with the countryspecific warranty requirements of the MPC/general distributor.

shown in red on vehicles with low mileage. Cause Directional control valve may stick. Remedy 1 Read off oil level in instrument cluster and correct if necessary. 2 Perform approx. 1015 engine starts, then clear fault codes. 3 Perform road test with vehicle. If fault code reoccurs during road test: Install new directional control valve.

Fault codes U019F00 or U019F87 current/stored in MRG1 control unit. Cause Various causes Remedy Perform guided test for fault code U019F with XENTRY diagnosis. Verify the following connections are clean and tight. Correct any problems and retest pump actuation: 12V plug at M75/11 48V plug at M75/11 48V connector X192/4 Connections at 48V fuse box F153/2 Sockets 1,2, and 5 at connector 2 of MRG1 control unit M75/11 circuit 41 ground If actuation and above connections are OK, but resistance between M75/11 and engine block is less than 2 ohms or heat shield touching coolant pump, proceed with below steps. 1Modify engine insulation per attached instructions. 2Remove engine control module and measure continuity within control unit between connector 2 pin 1 and connector 6 pin 2. 2aIf open circuit is found, replace engine control unit (MRG1) and perform initial startup. Refer to XENTRY parts information group 54/054 item 300. 3Clear faults and verify M75/11 operating normally.

This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 Allwheel drive (ARS) N127 'Drivetrain' (PTCU) control unit Y3/8 Transmission control for 9gear transmission (VGS) N3/10 Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications Collect an oil sample of the original fluid 5. Complete all transfer case Techin processes located under VG Control Unit > Adaptations Resetting the oil service data Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature (>60C ) 6. Operate vehicle in full circle with steering at full lock 5x to the left 5x to the right Return the vehicle to the client and request they drive the vehicle for at least 200 miles and return if the concern is not resolved. The extended drive will ensure the clutches are properly conditioned with the new oil and should resolve the concern. If this LI has already been applied to the vehicle, please submit a TIPS case to the Powertrain inbox with the following information: Initial quick test with fault freeze frame data Initial transmission EEPROM data VGS and Transfer Case Control Unit Log (N45 or N15/7) Special Acquisition Data .txt file (Transfer Case Control Unit > Special Procedures > Procedures for support queries to market support > Special Data Acquisition) Photo of the original oil condition What color was the fluid drained from the transfer case before the oil change? Was an oil sample collected, and can you provide a photo of the original fluid? What color and part number fluid was used during the oil change? How far was the vehicle driven after?

(figure 1) On the abovementioned vehicles with a mileage up to 15,000 km (about 9,300 mi), noises can occur from the rear axle differential. Cause Drivetrain resonance caused by the gear mesh of the ring and pinion in the rear axle differential in combination with installed damper elements on the axle shafts. Remedy For precise noise analysis and localization, use the chassis ear/NVH kit and the following driving procedure: 1. Drive the vehicle in a tight circle with the steering at full lock in both clockwise and counter clockwise directions. Vary engine load during the maneuvers If a foghornlike noise occurs comparable to the reference video, the vehicle exhibits the condition If the noise is present: 1. Add 15 ml of additive (Friction Modifier) into the rear axle differential via the filler plug IMPORTANT NOTE: Do NOT use Friction Modifier in vehicles equipped with an electronically controlled locking differential (Code 467). 2. Tighten the filler plug 3. Drive the vehicle until the rear axle differential reaches operating temperature Note: Proper activation of the additive requires elevated oil temperatures After the test drive to operating temperature, evaluate the noise when the rear axle is cold and when warm. If the noise is no longer present: The issue is resolved and the vehicle can be released. If there is noticeable improvement: The vehicle can be released with the explanation that the noise will gradually disappear over an extended driving distance. If the noise is still present and remains unchanged: Replace the rear axle differential.

*NOTE Use of tracer DYE for leak checks is not approved. Only approved leak check procedures as per WIS are approved. Cause Possible refrigerant leak. Remedy Perform the following measures : *Important* Photo documentation requirement is no longer in effect as of 10/1/2025. Remedy 1: Replace Evaporator (Only applies to vehicles produced PRIOR to April 15, 2022 and has NOT had the evaporator replaced previously) 1. Ensure that the rest of the AC system has been thoroughly checked for leaks with forming gas as per WIS before condemning the evaporator. 2. If no other leaks are found, replace the evaporator 3. *Important* when you get the new evaporator, check the expansion valve bracket to see if there are any bends (see attachment "Bent Bracket"). a. If bent, remove the expansion valve and bracket and check for damage to the flange (see attachment "Flange Damage"). i. If damage is found, order another evaporator and claim the part under parts warranty. The warranty claim MUST include a photo of the damage found. ii. If no damage is found, flip the bracket and torque to 7Nm. Check the evaporator for proper sealing before fully installing. b. If no bends are found, the evaporator should be installed in the vehicle. Note *If the evaporator housing has been opened or the evaporator or housing has been tampered with, the claim will be debited. Remedy 2: (Applies to all vehicles produced on or AFTER April 15, 2022 up to August 1, 2025) 1. Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . 2. If no leaks were found AND the system came in with no cooling/low charge, OR the evaporator is suspected of leaking: 3. Replace ONLY the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00, in accordance with the procedure outlined in WIS document AR83.30P5520ME. 4. IF THE PRODUCTION DATE IS BETWEEN JUNE 1, 2023 AND JULY 1, 2024, REPLACE THE DRYER AS WELL. (NOT THE CONDENSER) 5. After, charge the system and perform a few drive cycles. 6. Recheck the vehicle for leaks. 7. If no leaks are found, the vehicle can be released. 8. If a minor leak is detected that is less than 50ppm, then perform the following steps: If a leak is detected, fill the system with forming gas Close all doors and windows for 10 minutes. Vehicle off with no blower activation. Open the driver's door and measure ppm detection as soon as the door is open and the sniffer goes into the vehicle. If no leaks are measured, fill the system and release. Remedy 3: (Only applies to vehicles produced AFTER August 1, 2025) Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . If no leaks are found or the expansion valve has been found to be leaking, remove the expansion valve and check the bracket. If the bracket is bent, replace the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00. In the warranty submission, include photos of both sides of the bracket and a side profile so it can be seen that the bracket is bent. If the bracket is NOT bent or leaks from other locations are found, then open a TIPS case with the following: 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 4. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel if the evaporator is suspected. (see attached videos) 5. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 6. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the

and 725.1 (NAG3 facelift/9GTRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the ongoing quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 AMG sports models (AMG 43 and AMG 53 with converter) NAG3 AMG 63 NAG3 Hybrid NAG3 Facelift (automatic transmission 725.1) NAG3 facelift (725.1) with engine 139/177 (AMG 43/63) Steps for the Service Advisor: Important: The more information and detail that can be given to the workshop about the complaint, then the more effective the subsequent diagnosis with IPR can be. To this end, a detailed service reception questionnaire has been provided to help the Service Advisor ask the right questions about the complaint. Ask precise details about the customer complaint and the conditions and context. Fill out the service reception questionnaire (please see WIS document: OF27. 00P300005A) for customer complaints in detail and forward it to the workshop. Operation steps for the workshop employee: Perform quick test Access the transmission control unit via XENTRY Diagnosis Select "A customer complaint has been received" and carry out all subsequent operation steps (IPR diagnosis path). The IPR repair instructions are displayed. Carry out the IPR repair instructions without performing any further diagnostic or repair steps. Important: The IPR repair instructions are binding and must be carried out. Differing repairs are possible; such repairs must be documented in XENTRY in free text. Please observe the information regarding the IPR diagnosis process in XENTRY. Conventional diagnosis and subsequent appropriate repairs are only permitted if IPR does not specify any repair instructions. Invoicing for the guided IPR steps: Operation item 270640 and 0.1 hours !!!!! Notice regarding warranty: !!!!! The use of IPR in association with warranty claims is mandatory! If the IPR repair instructions are disregarded without justification, the warranty claims may be rejected and/or are subject to debit. IPR will provide a measure to repair the vehicle based on various data sources (EEPROM, fault codes, etc). Please consider the vehicle maintenance record of the vehicle. For warranty and goodwill repairs, the transmission ECU test log and/or IPR test result must be uploaded into Paperless XENTRY Diagnosis (pXD) . If repair is being determined based of oil pan condition pictures of oil pan MUST be provided to warranty as justification. Tamperproof documentation: The IPR repair instructions are stored in the control unit log. Please file this document in a tamperproof manner either in digital form or as a hardcopy printout and also enclose a printout with the damaged part. In this regard, please comply with the countryspecific warranty requirements of the MPC/general distributor.

Cause Frictional vibrations Remedy The intent of this document is to reduce noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some scenarios are normal and some are induced by driving style like those listed below: Driving style such as two footed driving where the pad might be in constant contact with the rotor. Brake pressure and application style (stopandgo traffic with consistent light brake pressure riding brakes where the brakes cannot cool sufficiently between applications). This can cause the brake pads to glaze and have a smooth/glassy surface which can induce noise. When ambient temperatures rise during summer peak and during cooling and cold winter months. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 34 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to reassessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the pistonside brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and reapply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper /carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the pistonside brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off

Cause Optimized brake pads may produce some noise and is normal at low speeds and light pressure. If the noise begins when the weather is colder, brake noise during this time is normal and the below remedy will not rectify. Remedy NOTE: Exchanging brake discs for noise is not a permanent measure for noise mitigation and cannot be claimed under warranty according to this LI. If the brake pads have not been exchanged prior, vehicle is newer, and this is the first visit for brake noise: Wipe down brake disc and remove any brake dust from holes in brake disc. GLE ONLY Replace brake pads and spring clips. Ensure the double sided adhesive is applied to all locations where the pistons contact the brake pad backing plate. See attachment "Adhesive and Copper Paste Application Area Series 167". Apply Molykote to the sides of the brake pad backing plate in the location shown in the attachment "Adhesive and Copper Paste Application Area Series 167". Clean brake components thoroughly from brake dust, road debris, and other foreign material. After replacing, place the vehicle in sport or sport plus mode and engage brake pedal for 30 seconds. Bed brakes during quality checking according to LI42.10P063502 but only perform once. If the brake pads have been exchanged in a prior visit: The following portion is not warrantable, some brake noise, especially with sport brake packages, is normal. The below is intended to assist in reducing or mitigating brake noise for customer satisfaction purposes. Inspect the condition of the brake system per WIS. Some level of noise is acceptable and cannot be mitigated or removed at all times. Below is a list of items that can cause or exacerbate noises but are normal. With use there will be dirt, debris, brake dust, and other foreign contaminants. If the system is dirty, components should be thoroughly cleaned and wiped down. Inspect the condition of the brake pads and discs. Note any visual anomalies such as glazing, excess rust formation, pad imprints from long stationary times, etc... Driving styles. Does the noise only occur at very low speeds when coming to a stop such as with very light brake pressure? When coming to a stop and applying increased brake pressure, does the noise reduce or disappear? If so, this is normal operation. Brake pressure and application style (stopandgo traffic with consistent low brake pressure riding brakes where the brakes cannot cool sufficiently between applications). Ambient temperatures, especially colder ambient temperatures. Lower ambient temperatures can also introduce additional road debris, such as salt.

Remedy Check the compressor's index and part number Figure 1 against Table 1. If listed please perform the following: 1. Replace the compressor, drier, and expansion valve using the applicable WIS instructions. 2. Flush the system using the applicable WIS instructions.

Cause During diagnostics of a front end noise, workshop is under the impression the noise is coming from the steering gear. Remedy If the root cause of the noise cannot be found and is seemingly from the steering rack, perform the below LI's and diagnostics. If they have been performed and the root cause still cannot be determined, a TIPS case must be opened to the Body/Chassis/Entertainment team prior to replacing the steering rack. LI46.35P067339 "Rattling, Humming, Dry Sliding/Gravel Noise When Steering" LI46.35P071461 "Check Tie Rod Outer Joint of Steering Gear" LI46.10P077391 "Knocking Noise In The Area Of The Steering Gear or Steering Column Tube When Braking Or Moving Off; The Steering Wheel Can Also Be Felt To "Crack"" Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Keep the boot clamps in case the rack is returned. If the noise is described as "clacking" or "knocking" when moving the wheel back and forth in quick oscillations and the thrust element in the steering rack has NOT been checked yet, please perform a check and subsequent adjustment, if necessary, as detailed in AR46.20P0601ME. Remove sway bar links and see if noise persists. Perform NVH timedomain noise diagnosis pointing to the steering rack as the root cause. The TIPS case must contain the following: Video underneath the vehicle with clearly audible noise while engine is running. Video inside the vehicle with clearly audible noise while engine is running. Vehicle checked for history of collisions. Vehicle history checked for other noise complaints in the area. List of other checked components (suspension, drive line components, wheel bearings, etc...). Along with the audible noise, does the feel/noise change through only a certain part of the steering arc sweep? Provide the thrust element before and after readings.

It will also ensure that if a case is necessary, all supporting documentation is available. This should not be used on its own as justification for creating a TIPS case. Cause The root cause will vary depending on the complaint. The goal of this document is to provide diagnostic checks and procedures that may help resolve customer complaints without opening a TIPS case. Remedy Before opening a transmission-related TIPS case, the following steps must be performed to ensure all relevant data has been collected and possible remedies (when applicable) have been performed. Please Note: At minimum, the documents below must be collected before proceeding to ensure the data in its original state when the vehicle arrived is captured. - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - Initial EEPROM data (.txt format) - IPR Result (if applicable. See LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool) - Transmission Heath Page If the vehicle has previously been repaired for the same concern, note the date, mileage, and TIPS case or RO number, along with a brief description of the prior work performed. IPR Guidance: The IPR recommended repair should be completed prior to following any steps in this LI and prior to case creation. IPR repairs do not require additional warranty approvals or a TIPS case to validate/confirm the results. To ensure efficient case handling, please avoid opening TIPS cases for this reason. For further information regarding IPR please see the following documents: LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool Oil Pan Condition Evaluation: In some situations, IPR will advise checking the oil pan condition and determining a repair based on the evaluation. Example photos in Xentry can be found in two ways: Use the blue hyperlink in the IPR result, and it will take you to the Condition check of transmission oil Navigate to Xentry Bluebook > Help for control unit > Condition check of transmission oil If a different repair that what is recommended by IPR is performed, attaching photo documentation of the complaint vehicle oil pan and the IPR example to the claim is required. Reproducing the Concern: Proper evaluation of transmission concerns generally requires the condition to be reproducible. It is recommended to compare the vehicle to a similar model, if available, to help determine whether the shift behavior is characteristic of the drivetrain or uncharacteristic for the vehicle. If the concern cannot be duplicated: A test drive with the customer may assist in understanding and reproducing the complaint. The vehicle shift quality should be compared to a known-good vehicle with identical drivetrain and model year. Check Shift Quality History (VGS Control Unit > Adaptations > Shift Quality History) Shift Quality History will show the last 5 noticeable harsh shifts and some of the parameters in which it occurred. You can use this to attempt recreation of the operating conditions and increase likelihood of reproducing the complaint. Complaint A: Shift Quality Note: Certain AMG variants may exhibit more firm and noticeable shift behavior as a normal characteristic. Refer to LI27.60P075147 for additional information. 1. Perform Valve flushing procedure 2. Perform 5 Torque Converter adaptions in a row - Allow the vehicle to warm up naturally, DO NOT power brake as it will increase the temperature in the torque converter. - After the 5th adaptation, collect a screen shot showing all 5 on one page 3. Perform a standstill adaption - collect a screen shot Recheck vehicle operation. If the concern has not improved, driving adaptations should be performed to target specific gear shifts.

Cause During diagnostics of a front end noise, workshop is under the impression the noise is coming from the steering gear. Remedy Workshop diagnostics point to the steering gear as the root cause of the noise and the below LI's and items have been ruled out. LI46.35-P-067339 - "Rattling or Humming Noise When Steering" LI46.35-P-071461 - "Check Tie Rod Outer Joint of Steering Gear" LI46.10-P-077391 - "Knocking Noise In The Area Of The Steering Gear or Steering Column Tube When Braking Or Moving Off; The Steering Wheel Can Also Be Felt To "Crack"" If the noise is described as "clacking" or "knocking" and the thrust element in the steering rack has NOT been checked yet, please perform a check and subsequent adjustment, if necessary, as detailed in AR46.20-P-0601ME. If the above has been completed and the noise is still present, please continue with the below: Video underneath the vehicle with clearly audible noise. Video inside the vehicle with clearly audible noise. Vehicle checked for history of collisions. List of other checked components (suspension, drive line components, wheel bearings, etc...). Check integrity of dust boots and dust boot clamps. Ensure no water has entered into the steering rack. Along with the audible noise, does the feel/noise change through only a certain part of the steering arc sweep? Provide the thrust element before and after readings. If the above is completed and no findings are noted, please open a TIPS case to the Body/Chassis/Entertainment inbox.

Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% a negative charge balance A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked). Vehicles with code B01+801: When charging while stationary, the 48V battery must have a state of charge (SOC) of 70% before the 12V primary battery, or the secondary battery in the case of code 503, can be charged. To ensure optimum battery care, please also comply with the existing Service Information documents regarding the handling of stock vehicles (SI54.10-P-0024A) and on remaining in transport mode (SI54.00-P-0004A) until immediately before handover to end customers. Special note: Do not replace any parts, if the message has occurred due to battery discharge as a result of the driving profile or the ignition being switched on (see attached examples); in such cases separate warranty and goodwill invoicing is not possible, as this is a normal on-board electrical system protection function. Likewise battery care and recharging do not qualify as a W&G case. Please advise customers accordingly regarding the above-mentioned issues relating to vehicle use.

Cause Optimized brake pads may produce some noise. Remedy If the brake pads have not been exchanged prior and this is the first visit: Wipe down brake disc and remove any brake dust from holes in brake disc. Replace brake pads and spring clips. Ensure the double sided adhesive is applied to all locations where the pistons contact the brake pad backing plate. See attachment "Adhesive and Copper Paste Application Area - Series 167". Apply Molykote to the sides of the brake pad backing plate in the location shown in the attachment "Adhesive and Copper Paste Application Area - Series 167". Clean brake components thoroughly from brake dust, road debris, and other foreign material. After replacing, place the vehicle in sport or sport plus mode and engage brake pedal for 30 seconds. Bed brakes according to LI42.10-P-063502 but only perform once. If the brake pads have been exchanged in a prior visit: Inspect the condition of the brake system per WIS. Some level of noise is acceptable and cannot be mitigated or removed at all times. Below is a list of items that can cause or exacerbate noises but are normal. With use there will be dirt, debris, brake dust, and other foreign contaminants. If the system is dirty, components should be thoroughly cleaned and wiped down. Inspect the condition of the brake pads and discs. Note any visual anomalies such as glazing, excess rust formation, pad imprints from long stationary times, etc... Driving styles. Does the noise only occur at very low speeds when coming to a stop such as with very light brake pressure? When coming to a stop and applying increased brake pressure, does the noise reduce or disappear? If so, this is normal operation. Brake pressure and application style (stop-and-go traffic with consistent low brake pressure riding brakes where the brakes cannot cool sufficiently between applications). Ambient temperatures, especially colder ambient temperatures. Lower ambient temperatures can also introduce additional road debris, such as salt. NOTE: Exchanging brake discs for noise is not a permanent measure for noise mitigation and is not recommended for noise concerns unless there are other factors involved.

*NOTE - Use of tracer DYE for leak checks is not approved. Only approved leak check procedures as per WIS are approved. Cause Possible refrigerant leak. Remedy Perform the following measures : *Important* - Photo documentation requirement is no longer in effect as of 10/1/2025. Remedy 1: Replace Evaporator (Only applies to vehicles produced PRIOR to April 15, 2022 and has NOT had the evaporator replaced previously) 1. Ensure that the rest of the AC system has been thoroughly checked for leaks with forming gas as per WIS before condemning the evaporator. 2. If no other leaks are found, replace the evaporator Note - *If the evaporator housing has been opened or the evaporator or housing has been tampered with, the claim will be debited. Remedy 2: (Applies to all vehicles produced on or AFTER April 15, 2022 up to August 1, 2025) 1. Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . 2. If no leaks were found AND the system came in with no cooling/low charge, OR the evaporator is suspected of leaking: 3. Replace ONLY the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00, in accordance with the procedure outlined in WIS document AR83.30-P-5520ME. 4. IF THE PRODUCTION DATE IS BETWEEN JUNE 1, 2023 AND JULY 1, 2024, REPLACE THE DRYER AS WELL. (NOT THE CONDENSER) 5. After, charge the system and perform a few drive cycles. 6. Recheck the vehicle for leaks. 7. If no leaks are found, the vehicle can be released. 8. If a minor leak is detected that is less than 50ppm, then perform the following steps: If a leak is detected, fill the system with forming gas Close all doors and windows for 10 minutes. Vehicle off with no blower activation. Open the driver's door and measure ppm detection as soon as the door is open and the sniffer goes into the vehicle. If no leaks are measured, fill the system and release. Remedy 3: (Only applies to vehicles produced AFTER August 1, 2025) Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . If no leaks are found or the expansion valve has been found to be leaking, remove the expansion valve and check the bracket. If the bracket is bent, replace the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00. In the warranty submission, include photos of both sides of the bracket and a side profile so it can be seen that the bracket is bent. If the bracket is NOT bent or leaks from other locations are found, then open a TIPS case with the following: 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 4. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel if the evaporator is suspected. (see attached videos) 5. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 6. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 7. Provide photos of both sides of the bracket and a side profile so it can be seen that the bracket is not bent. 8. Open a TIPS case in the HV/LV inbox labeled "167 AC leak after April 1, 2025" with all attachments. NOTE: (Applies to all 167's) Please see the list of WIS documents for forming gas leak check and recharging of the system. Review PCTT 9/25 for forming gas best practices. Review PCTT 5/25 for bracket removal best practices. See attachment for further instructions.

Please follow the relevant guided tests for the 223 and 206. For 223 with fault code B1FCB97 follow LI54.10-P-076026. Various causes are possible. The faults listed in the various causes do not all have to be present at all times. Some of these complaints may overlap. Rely on the faults listed in the Cause section for identifying the correct Remedy. 1. No start 2. Yellow or red instrument cluster message for 48 V on-board electrical system battery (G1/3) 3. Limp home mode, overheating, A/C not blowing cold, or loss of acceleration 4. Check Engine Light Cause Cause 1: Software causes Intermittent No Starts with fault B183387 in DC/DC converter N83/1 Cause 2: Software causes Permanent No Start with fault B183349. May also have fault B183371. Cause 3: Hardware short circuit in 48V system causes fault B183319 in 48V battery. May also have fault B183371. Cause 4: Internal 48V battery Peltier cooling element failure causes fault B183397 Cause 5: This will Always have fault code B183371 but different from cause 2 and 3 -- it will Not have B183349, B183319, or any other faults in the 48V battery. This will only have fault B183371 in 48V battery. Cause 5 is from the 48V battery detecting an abnormality which then causes the 48V battery to disconnect itself. The disconnected 48V battery then causes subsequent symptoms: Limp Home Mode, overheating, A/C not blowing cold, or loss of acceleration Cause 6: Check Engine Light with fault P0606F1 in the N127 PTCU Cause 7: Check Engine Light with possible no start and fault P057FF1 Remedy Note: each of these remedies correspond to a specific cause. Make sure to match correct Cause with Remedy. Remedy 1: 1. Check the 12V power supply and LIN connection 2. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 3. Road test and release vehicle if no further symptoms Remedy 2: 1. Charge the 12V battery (Charging current <5A) 2. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 3. Road test and release vehicle if no further symptoms If the faults return or cannot be cleared: 1. XENTRY MUST be connected with VCI cable to correctly complete this remedy. 2. Complete guided test for B183349. 3. If guided test completes, vehicle starts, and drive cycles show no further symptoms, release vehicle. 4. If after guided test completes, XENTRY states to replace 48V battery: replace only 48V battery. If vehicle is a MY21 w/M256 engine, update SW in 48V battery 5. If this is a repeat visit for fault B183349 and guided test has already been completed, open a TIPS case. 6. If guided test does not complete OR symptoms are still present open a TIPS case. 7. If communication cannot be established with 48V battery perform physical layer check at 12V wiring to DCDC. If no abnormalities found, replace the 48V battery. 8. If guided test completes but a new fault code is present (such as B183319, B183371, etc.) follow the relevant Cause/Remedy for that fault in this LI. Remedy for 3: (If this occurred after Campaign 2025050001, this Li does not apply and LI54.10-P-079772 should be followed) 1. If fault is not Current (only Stored): 1. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 2. Road test and release vehicle if no further symptoms If the faults return or this is a second visit after the SW update: 1. Complete the guided test for B183319 2. Perform XENTRY actuations for all 48V components. 3. Create a TIPS case with ALL Preliminary measures required as noted below for Remedy 5 4. Upload to TIPS case ISA performance data from the N129. 5. ISA performance data location in XD: 6. N129 control unit under Special Procedures 7. "Procedures for support queries to market support" 8. "Collation of diagnosis performance data" 9. "engine at idle" See attachment for further instructions.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

'A' has a short circuit to positive stored in VGS control unit. Cause Electrical failure of oil pressure sensor integrated into VGS Control Unit Remedy Intelligent Predictive Repair (IPR) recognizes this fault pattern and will provide the necessary repair suggestion. 1. Perform IPR and follow the recommended procedures 2. Replace complete EHS valve body, fill to near max fluid level, & complete initial start-up - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement.

Cause During diagnostics of a front end noise, workshop is under the impression the noise is coming from the steering gear. Remedy Workshop diagnostics point to the steering gear as the root cause of the noise and the below LI's have been ruled out. LI46.35-P-067339 - "Rattling or Humming Noise When Steering" LI46.35-P-071461 - "Check Tie Rod Outer Joint of Steering Gear" LI46.10-P-077391 - "Knocking Noise In The Area Of The Steering Gear or Steering Column Tube When Braking Or Moving Off; The Steering Wheel Can Also Be Felt To "Crack"" If the above has been completed and the noise is still present, please continue with the below: Video underneath the vehicle with clearly audible noise. Video inside the vehicle with clearly audible noise. Vehicle checked for history of collisions. List of other checked components (suspension, drive line components, wheel bearings, etc...). Check integrity of dust boots and dust boot clamps. Ensure no water has entered into the steering rack. Along with the audible noise, does the feel/noise change through only a certain part of the steering arc sweep? If noise is described as a "clacking" noise when moving the steering wheel back and forth, please navigate to WIS and find and perform the document "Setting play between thrust element and steering rack". Provide both pre-adjustment and post-adjustment numbers. If the above is completed and no findings are noted, please open a TIPS case to the Body/Chassis/Entertainment inbox.

or without Illumination of Check Engine Light with DTC's C10159A (A108/2, A108/3) and P0AFB00 (N129) Cause PTCU software robustness. Remedy Check N127 - PTCU (Powertrain Control Unit) hardware and software numbers. If software number matches a "Hardware Number" and "Predecessor Software #", update software. If software number is not shown in "Predecessor Software #" and condition exists, open a TIPS case to the High Voltage/ Low Voltage inbox.

P13C273 P13C278 P140473 Cause Various Remedy Model year 2024 254 and 167 with engine M254 -Update software of N127 PTCU. New software: 254- A2549022611 167- A2549022811 -Clear fault codes and check operation of the exhaust flap. Models with M256, or models with M254 after SW update -Check exhaust flap for free movement via actuation. -Remove flap actuator and check movement of flap in exhaust pipe. Replace exhaust pipe section if flap is binding. -Replace flap actuator if above checks are ok. If fault code returns after performing the above steps, open a TIPS case with the powertrain team. Note: Codes P13C273 and P13C278- Right side flap Code P140473- Left side flap

This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications - Collect an oil sample of the original fluid 5. Complete all transfer case Tech-in processes located under VG Control Unit > Adaptations - Resetting the oil service data - Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature ( >60C ) 6. Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Return the vehicle to the client and request they drive the vehicle for at least 200 miles and return if the concern is not resolved. The extended drive will ensure the clutches are properly conditioned with the new oil and should resolve the concern. If the concern continues to occur with the control unit disconnected or after the above steps have been performed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial quick test with fault freeze frame data - Initial transmission EEPROM data - VGS and Transfer Case Control Unit Log (N45 or N15/7) - Photo of the original oil condition - What color was the fluid drained from the transfer case before the oil change? - Was an oil sample collected, and can you provide a photo of the original fluid? - What color and part number fluid was used during the oil change? - How far was the vehicle driven after?

ME-SFI control unit software does not meet current production specifications. As a result, a check engine malfunction indicator lamp might erroneously be triggered. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the ME-SFI control unit software.

*NOTE - Use of tracer DYE for leak checks is not approved. Only approved leak check procedures as per WIS are approved. Cause Possible refrigerant leak. Remedy Perform the following measures : *Important* - Photo documentation requirement is no longer in effect as of 10/1/2025. Remedy 1: Replace Evaporator (Only applies to vehicles produced PRIOR to April 15, 2022 and has NOT had the evaporator replaced previously) 1. Ensure that the rest of the AC system has been thoroughly checked for leaks with forming gas as per WIS before condemning the evaporator. 2. If no other leaks are found, replace the evaporator Note - *If the evaporator housing has been opened or the evaporator or housing has been tampered with, the claim will be debited. Remedy 2: (Applies to all vehicles produced on or AFTER April 15, 2022 up to April 1, 2025) 1. Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . 2. If no leaks were found AND the system came in with no cooling/low charge, OR the evaporator is suspected of leaking: 3. Replace ONLY the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00, in accordance with the procedure outlined in WIS document AR83.30-P-5520ME. 4. IF THE PRODUCTION DATE IS BETWEEN JUNE 1, 2023 AND JULY 1, 2024, REPLACE THE DRYER AS WELL. (NOT THE CONDENSER) 5. After, charge the system and perform a few drive cycles. 6. Recheck the vehicle for leaks. 7. If no leaks are found, the vehicle can be released. 8. If a minor leak is detected that is less than 50ppm, then perform the following steps: If a leak is detected, fill the system with forming gas Close all doors and windows for 10 minutes. Vehicle off with no blower activation. Open the driver's door and measure ppm detection as soon as the door is open and the sniffer goes into the vehicle. If no leaks are measured, fill the system and release. Remedy 3: (Only applies to vehicles produced AFTER April 1, 2025) *TIPS Case Required if leak is found other than a bent bracket* Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . If no leaks are found or the expansion valve has been found to be leaking, remove the expansion valve and check the bracket. If the bracket is bent, replace the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00. In the warranty submission, include photos of both sides of the bracket and a side profile so it can be seen that the bracket is bent. If the bracket is NOT bent or leaks from other locations are found, then open a TIPS case with the following: 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 4. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel if the evaporator is suspected. (see attached videos) 5. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 6. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 7. Provide photos of both sides of the bracket and a side profile so it can be seen that the bracket is not bent. 8. Open a TIPS case in the HV/LV inbox labeled "167 AC leak after April 1, 2025" with all attachments. NOTE: (Applies to all 167's) Please see the list of WIS documents for forming gas leak check and recharging of the system. Review PCTT 9/25 for forming gas best practices. See attachment for complete instructions

the vehicle is stationary and ECO Start/Stop is active (combustion engine is off). The noise is more noticeable outside the vehicle and in acoustically shielded areas such as closed rooms or garages. Cause The noise in the valve body (EHS) is caused by superimposed pressure peaks acting on the valves. This phenomenon occurs only after a certain running-in period due to the influence of micro-contamination in the valve bores. Remedy A hardware modification of the electro-hydraulic control unit (EHS) is currently being implemented (no change to the part number). This will be incorporated into series production and as a spare part starting from 12/2025. This is only a comfort-related complaint and has no impact on the functionality or service life of the transmission. For sensitive customers, the following measures can be performed: 1. Replace the electro-hydraulic control unit (EHS), the oil pan, and the transmission fluid. - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement. (See attached location guide)

Cause Vehicles with engine M264 and transmission 725.0 may be equipped with specific software versions. Remedy Update Transmission Software (VGSNAG3). 1. Perform IPR and update transmission control unit software - see list of new software numbers below A0009027479 A0009027579 A0009027779 A0019026209 A0019025909 A0019025809 A0019025609 A0019024809 A0019024309 A0019024709 After updating the software, isolated/intermittent instances of the concern may occur. 2. Perform a standstill adaptation and reevaluate concern. The vehicle can be released if no longer present

EEPROM or Transmission Health system following the replacement of the below components: - The electrohydraulic control unit (EHS valve body) in transmission 725.0/725.1 - The repair kit for the control unit (VGS) in transmission 725.0 Cause Missing, incorrectly installed, or damaged guide tubes on the EHS valve body. Remedy Check for the correct installation of the guide tubes (refer to attachments under Cause), correct installation if necessary. Parts Catalog References: NAG3M 725.1 AND NAG3C 725.0 (AMG only): Part numbers 100, 120, 150, 160 NAG3C 725.0 (Non AMG): Part numbers 280, 290, 330, 340 NOTE: If any of these guide tubes are not installed and the vehicle is driven, it will create several rinse and slipping events in the EEPROM data. These values caused by incorrect installation need to be erased to prevent future misdiagnosis. Submit a TIPS case to the Powertrain inbox with the following to receive the necessary reset password: - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - IPR Result - Initial EEPROM data (before repairs) - Latest EEPROM data - Photo of oil level ultrasonic measurement next to XENTRY specifications Please provide detail regarding the reasoning for the initial replacement in your workshop findings and measures performed. (This topic was covered in the July 2022 and July 2024 Passenger Car Tech Topics)

This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications - Collect an oil sample of the original fluid 5. Complete all transfer case Tech-in processes located under VG Control Unit > Adaptations - Resetting the oil service data - Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature ( >60C ) 6. Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right 7. Perform an extended 200mi road test to ensure the clutches are properly conditioned with the new oil. 8. Reassess the concern and release the vehicle if no longer present. If the concern continues to occur with the control unit disconnected or after the above steps have been performed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial quick test with fault freeze frame data - Initial transmission EEPROM data - VGS and Transfer Case Control Unit Log (N45 or N15/7) - Photo of the original oil condition - What color was the fluid drained from the transfer case before the oil change? - Was an oil sample collected, and can you provide a photo of the original fluid? - What color and part number fluid was used during the oil change? - How far was the vehicle driven after?

engine control unit software does not correspond to current production specification. The affected vehicles could exhibit rough engine running and noticeable vehicle vibrations, and misfire during the catalytic heating phase, resulting in check engine Malfunction Indicator (MIL) Lamp to illuminate. Additionally, it is possible that on-board diagnostics and/or exhaust gas emissions requirements may not be fulfilled. MBUSA will conduct an emission service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicle.

engine control unit software does not correspond to current production specification. The affected vehicles could exhibit rough engine running and noticeable vehicle vibrations, and misfire during the catalytic heating phase, resulting in check engine Malfunction Indicator (MIL) Lamp to illuminate. Additionally, it is possible that on-board diagnostics and/or exhaust gas emissions requirements may not be fulfilled. Remedy MBUSA will conduct an emission service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicle.

Cause In the groove where the pan seal is placed, there may be imperfections (porosity) in the casting causing fluid to leak past the seal. The supplier states this only affects rear differentials with 2023 production date. The production date can be found stamped on the housing cover (see attachment). Remedy 1. Follow the attached instructions to inspect the rear differential cover for porosity. 2. Repair the vehicle with the applicable repair kit for the chassis. - The new oil pans that come with the repair kit should be produced in 2024 and not have this issue. *When submitting the claim, please reference this LI document and if porosity was found.*

*NOTE - Use of tracer DYE for leak checks is not approved. Only approved leak check procedures as per WIS are approved. Cause Possible refrigerant leak. Remedy Perform the following measures : *Important* - Photo documentation requirement is no longer in effect as of 10/1/2025. Remedy 1: Replace Evaporator (Only applies to vehicles produced PRIOR to April 15, 2022 and has NOT had the evaporator replaced previously) 1. Ensure that the rest of the AC system has been thoroughly checked for leaks with forming gas as per WIS before condemning the evaporator. 2. If no other leaks are found, replace the evaporator Note - *If the evaporator housing has been opened or the evaporator or housing has been tampered with, the claim will be debited. Remedy 2: (Applies to all vehicles produced on or AFTER April 15, 2022 up to April 1, 2025) 1. Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . 2. If no leaks were found AND the system came in with no cooling/low charge, OR the evaporator is suspected of leaking: 3. Replace ONLY the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00, in accordance with the procedure outlined in WIS document AR83.30-P-5520ME. 4. IF THE PRODUCTION DATE IS BETWEEN JUNE 1, 2023 AND JULY 1, 2024, REPLACE THE DRYER AS WELL. (NOT THE CONDENSER) 5. After, charge the system and perform a few drive cycles. 6. Recheck the vehicle for leaks. 7. If no leaks are found, the vehicle can be released. 8. If a minor leak is detected that is less than 50ppm, then perform the following steps: If a leak is detected, fill the system with forming gas Close all doors and windows for 10 minutes. Vehicle off with no blower activation. Open the driver's door and measure ppm detection as soon as the door is open and the sniffer goes into the vehicle. If no leaks are measured, fill the system and release. Remedy 3: (Only applies to vehicles produced AFTER April 1, 2025) *TIPS Case Required if leak is found* Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . If any leaks are found, then open a TIPS case with the following: 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 4. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel if the evaporator is suspected. (see attached videos) 5. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 6. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 7. Open a TIPS case in the HV/LV inbox labeled "167 AC leak after April 1, 2025" with all attachments. NOTE: (Applies to all 167's) Please see the list of WIS documents for forming gas leak check and recharging of the system. Review PCTT 9/25 for forming gas best practices. Review PCTT 5/25 for bracket removal best practices. Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available. Ensure that the correct damage code is used for failed component. (see list of damage codes) Evaporator housings that have been disassembled, present with physical damage, or tags that show signs of tampering will be debited in full.

Cause During diagnostics of a front end noise, workshop is under the impression the noise is coming from the steering gear. Remedy Workshop diagnostics point to the steering gear as the root cause of the noise and the below LI's have been ruled out. LI46.35-P-067339 - "Rattling or Humming Noise When Steering" LI46.35-P-071461 - "Check Tie Rod Outer Joint of Steering Gear" LI46.10-P-077391 - "Knocking Noise In The Area Of The Steering Gear or Steering Column Tube When Braking Or Moving Off; The Steering Wheel Can Also Be Felt To "Crack"" After the above has been completed and the diagnostics point to a steering rack noise, please open a TIPS case to the Body/Chassis/Entertainment inbox with the following information: Video underneath the vehicle with clearly audible noise. Vehicle checked for history of collisions. List of other checked components (suspension, drive line components, wheel bearings, etc...).

system battery) from software release A 000 902 50 48 to software release A 000 902 15 89, the fault code B183319 may be output. B183319 "The battery for the 48V on-board electrical system has a malfunction. The limit value for current has been exceeded" Cause Anomaly in the software update Remedy Please perform the following steps in the specified sequence: 1.) Delete fault codes 2.) Disconnect XENTRY Diagnosis and the 12 V battery charger 3.) Disconnect ground cable from the 12 V battery 4.) Ensure bus idle for at least 10 minutes 5.) Re-connect ground cable to the 12 V battery 6.) Delete fault codes again 7.) Perform a test drive 8.) Check fault codes > If fault code B183319 is still current, continue with the guided fault analysis in XENTRY Diagnosis. > If fault code B183319 goes to stored and can be cleared, no further action is required.

clattering) can be heard underneath the bench seat, particularly in the case of a full tank (1/1 fill level). Cause The vibrating air column of the purge flow volume triggers the fill limit vent valve (FLVV) to open and close repeatedly when the fuel tank is full. Remedy By reducing the fuel quantity by around 5 liters, the noise can no longer be heard. In isolated cases, the noise can also be amplified by a fuel tank installed under stress and therefore lines adjacent to the body-in-white (above the fuel tank). In this case, the installation position of the fuel tank and the contact surfaces to the body-in-white must be checked. To do so, loosen the fuel tank and refasten it. Please do not replace component parts such as the fuel tank, activated charcoal canister, purge valve or delivery module, as this does not provide a remedy. If a similar noise can be heard with a tank fill level of, for example, 3/4 or 1/4 and not with a full tank (1/1), there is a different issue.

Cause Possible ME control unit software Remedy On applicable vehicles with complaint above, check for ME software updates and update as available. Afterwards ensure that the mixture adaptations are cleared by viewing the injector performance data in the ME. Perform a sensor rotor adaptation then perform an AMG engine adaptation drive. Afterwards drive the vehicle in "C" with ECO disabled for about 50 miles. This drive needs to be on surface streets (no steady state highway driving). Afterwards let the car go to sleep, then test drive it again and QC. If the complaint is no longer present, release the car to the customer. If there is no software update available OR if the complaint reoccurs, process the car via LI07.61-P-070707.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10P067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. Please update the Head unit software to E505.9

with one of the following scenarios: Flashing without a speed limit (" "). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. NOTE: Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Update head unit software to latest version and the recheck function in the same location. NOTE: Updated head unit software for AMG's has NOT been released yet. ETA 12/2026. If vehicle is still exhibiting one of the symptoms as described exactly as in the complaint section or as shown in the video attachments, open a TIPS case to the Body/Chassis/Entertainment inbox with the following: Video of the concern. Exact location (latitude and longitude is best)

with one of the following scenarios: Flashing without a speed limit (" "). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. NOTE: Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Update head unit software to latest version and the recheck function in the same location. If vehicle is still exhibiting one of the symptoms as described exactly as in the complaint section or as shown in the video attachments, open a TIPS case to the Body/Chassis/Entertainment inbox with the following: Video of the concern. Exact location (latitude and longitude is best)

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. NOTE: Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: The vehicle must be exhibiting the concern as shown in the attachment videos. The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. If the geographic location is known, it is very important that it is provided. Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q3 2026.

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.

2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. The following applies to model series 167 from AEJ 22/1 onward, 192 AMG, 206, 214, 223, 232 AMG, 236, 254, 290 AMG from AEJ 23 onward, 294, 295, 296, 297 and 465: Reinitialize ASSYST Plus under Adaptations Teach-in processes ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.

menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.

2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations Teach-in processes ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.

2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations Teach-in processes ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.

Cause Software A 40/12 - Head-up display and N133/1 - Instrument cluster (IC). Remedy Please do not replace any parts The following steps need to be performed in the order shown below: 1. Xentry > Special functions > 'Entry for retrofits and modifications' add SA code 2O8 (Two 'O' eight) (Please see the attachment) 2. Update the HUD177 software update to the latest available version 3. Update the IC177M software update to the latest available version (software A1779048302 )

Remedy Please do not replace any parts. Step1: Please add SA code 2O8 to the vehicle. Step2: Update the HUD177 to the latest SW Step3: Update the IC177M software update to the latest available version (software A1779048302 ) (E216.0)

Remedy Please do not replace any parts. Step1: Please add SA code 2O8 to the vehicle. Step2: Update the HUD177 to the latest SW Step3: Update the IC177M software update to the latest available version (software A1779048302 ) (E216.0)

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The robustness measure has been identified and is planned for implementation in the A26/17 E505.9 software. The E505.9 software is expected to be available in XENTRY Q3 2026.

REAR COMFORT PACKAGE (P08), the rear seat heating cannot be activated via voice control. However, the voice control erroneously provides feedback that the seat heating has been activated. Cause A26/17 - MBUX multimedia system (Head unit) software Remedy Software E604 (FUP6) corrects the erroneous feedback from the head unit regarding the activation of the seat heating. Important note: The feature "Activation of seat heating via voice control" is only available in vehicles with codes REAR SEAT ENTERTAINMENT (854/447/864) and 903 REAR COMFORT SEAT HEATING (903) or REAR COMFORT PACKAGE (P08) Availability: Software FUP6 is planned to be released in Q3 2026. Note: Please do not replace any parts for this concern.

The UI continues to show the old stations artwork instead of updating to the new one. Cause Root cause currently being investigated. Remedy Please do not replace any parts. Please create a TIPS case to Body/Chassis/Entertainment inbox.

NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. Cause Calibration of the reversing camera is in progress. This is not a malfunction, but an intended system behavior. Remedy An optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Update both control units and perform on SCN coding: A26/17 (Head Unit) N62/* (PARK Control Unit) IMPORTANT: After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. Prior to releasing the vehicle, please verify the following: Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will reopen, when calibrating, at 9 MPH. The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. This is only for customer satisfaction purposes. Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. Remedy For customer satisfaction purposes, an optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Update both control units and perform on SCN coding: A26/17 (Head Unit) N62/* (PARK Control Unit) IMPORTANT: After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. Prior to releasing the vehicle, please verify the following: Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will reopen, when calibrating, at 9 MPH. The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q4 2025 to early Q1 2026 to rectify concern.

NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. This is only for customer satisfaction purposes. Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. Remedy For customer satisfaction purposes, an optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Update both control units and perform on SCN coding: A26/17 (Head Unit) N62/* (PARK Control Unit) IMPORTANT: After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. Prior to releasing the vehicle, please verify the following: Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will reopen, when calibrating, at 9 MPH. The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. This is only for customer satisfaction purposes. Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. Remedy For customer satisfaction purposes, an optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Update both control units and perform on SCN coding: A26/17 (Head Unit) N62/* (PARK Control Unit) IMPORTANT: After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. Prior to releasing the vehicle, please verify the following: Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will reopen, when calibrating, at 9 MPH. The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

attachment) Head-up display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus (see attachment) Cause Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC) Remedy Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC). Update: A new software version is planned to be released by the end of 2026. Once confirmed the LI will be updated. TIPS cases are no longer needed. Note: Please do not replace any parts for this complaint. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

Cause Under Analysis Remedy 1.Reset the MBUX language (e.g., if the MBUX language is set to English, please change it to any other language and then set it back to English again) 2.If the issue still persists after the step 1, Perform a user data reset of the Head Unit. If the above 2 steps still don't repair the issue, please open a TIPS case. Note: Please do not replace any parts

the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.

NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. This is only for customer satisfaction purposes. Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. Remedy For customer satisfaction purposes, an optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Update both control units and perform on SCN coding: A26/17 (Head Unit) N62/* (PARK Control Unit) IMPORTANT: After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. Prior to releasing the vehicle, please verify the following: Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will reopen, when calibrating, at 9 MPH. The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q4 2025 to early Q1 2026 to rectify concern.

attachment) Head-up display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus (see attachment) Cause Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC) Remedy Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC). Update: A new software version is planned to be released by the end of 2025. Once confirmed the LI will be updated. TIPS cases are no longer needed. Note: Please do not replace any parts for this complaint. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

attachment) Head-up display permanently or sporadically unavailable - without warning message in driver display. Display permanently or sporadically discolored and out of focus (see attachment). Cause Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC). Remedy Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC). Update: A new software version is planned to be released by the end of 2025. Once confirmed the LI will be updated. TIPS cases are no longer needed. Note: Please do not replace any parts for this complaint. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

attachment) Head-up display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus (see attachment) Cause Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC) Remedy Software for the A40/12 - Head-up display and N133/1 - Instrument cluster (IC) is now available. Please update both control units. TIPS cases are no longer needed. Note that issues may still occur even after the software updates. Please do not replace any parts. We will inform you as soon as a solution is available. Note: Please do not replace any parts for this complaint. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

REAR COMFORT PACKAGE (P08), the rear seat heating cannot be activated via voice control. However, the voice control erroneously provides feedback that the seat heating has been activated. Cause A26/17 - MBUX multimedia system (Head unit) software Remedy Software E604 (FUP6) corrects the erroneous feedback from the head unit regarding the activation of the seat heating. Important note: The feature "Activation of seat heating via voice control" is only available in vehicles with codes REAR SEAT ENTERTAINMENT (854/447/864) and 903 REAR COMFORT SEAT HEATING (903) or REAR COMFORT PACKAGE (P08) Availability: Software FUP6 is planned to be released in Q4 2025. Note: Please do not replace any parts for this concern.

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Head unit software variant. Remedy For all chassis use Xentry to update head unit (A26/17). Target boot software number should be either: 247 904 6600 (E905.4) OR 247 904 7500 (E906.1) If vehicle fits all criteria and either target software is not available via Xentry, please open an XSS ticket. Damage code 5424x-01 may be used with a repair start date after June 2nd, 2025.

control unit software for the front signal acquisition and actuation module (SAM-F) may not correspond to the current series production configuration and it is possible that a communication error may occur. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will perform a software update of the front signal acquisition and actuation module.

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by doubleclicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module NOTE: Occasionally to verify complaint, the steering column/vehicle needs to be in direct sunlight or hot conditions for a few hours. If noise only occurs when adjusting the steering column via electric actuation, please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on all pivot points including, but not limited to, green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, wipe excess grease off and perform greasing and movement to limit stops in all directions again. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. Include detailed items of the following: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

Complaint No. 1: Sporadic "Headlamp Inoperative" message in the instrument cluster (IC), fault code in control unit N10/6 FSAM: U118A02 communication with the left headlamp range adjustment control unit is faulty. General signal fault. or U118A08 Communication with the left headlamp range adjustment control unit is faulty. Faulty signal or faulty message. Complaint No. 2: The instrument cluster (IC) displays the message "Adaptive High Beam Assist inoperative"; fault code present in LED control unit E1n11 or E2n11: B178392 "LED driving light actuation" control unit is faulty. Function or command is faulty. Cause Complaint No. 1: software fault. Complaint No. 2: undervoltage threshold value set inappropriately during vehicle start. Remedy For complaint No. 1 and No. 2: Perform a software update on all headlamp and LED control units: E1n9, E1n11, E2n9 and E2n11 If the fault persists: For complaint No. 1: Replace HLI E1n9 control unit. For complaint No. 2: Replace PXL E1n11 or E2n11 control unit. Note: Headlamps must not be replaced for these complaints.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again and anywhere there are movement or friction points that the noise seems to be emanating from. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

There is an implausible signal." In the quick test, there are also no other DTC's in other control units that point to or reference N80 Steering Column Control Module ("SCCM"). There is no effect on any other components or vehicle functions and it does not cause an instrument cluster light. Cause The DTC only ever occurs during initialization (initialization occurs after bus sleep). The SCCM then resets itself. Remedy 1. If the error is stored and no other control unit points to the N80 SCCM ignore and erase. Software expected in Q4 2026. 2.If the DTC is in the N80 SCCM AND the following DTC's are in N30/3 (Electronic Stability Program) and N68 (Electric Power Steering): N30/3 ESP: U071286, Steering column tube module control unit has a malfunction. There is an incorrect signal. N68 EPS: U042986, Implausible data were received from the steering column module. There is an incorrect signal. Please open a TIPS case to the Body/Chassis/Entertainment inbox.

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 double-click on the locking button As of modification year 22/1, by pressing and holding the locking button + double-clicking on the release tab On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

U013281 - Communication with control unit "Suspension" has a malfunction. Incorrect data were received. C156F00 - The signal values of the level sensors are implausible. Cause Physical layer wiring to the level control sensors B22/X. Remedy Check A108/2 and A108/3 for freeze frame data section "ZF_error_handler". The text will provide a good place to start. Example: "SPC_FEHLER_VehLvl_Stat_HP_AMG_AR2_SNA_VehLvl_RR_V2_AMG" indicates the Right Rear may have initiated the DTC. See attached picture for reference. Is concern reproducible? If so, watch actual values in Xentry and see which sensor is setting the implausible value. Use Hioki to measure wiring to all four level sensors from N51/8. Use above DTC freeze frame data to physically inspect specific wiring as mentioned in the freeze frame data above. Check all level sensors for damage, correct mounting, level sensors bound or not moving, etc... If vehicle exhibits concern after all of the above is completed, please open a TIPS case to the Body, Chassis, Entertainment Inbox.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The instrument cluster message and the FC memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 206 and 223 with code 802: Perform SCN coding in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Please do not replace any parts even if the FC P0CFE00 coding continues to appear after successfully completing this step. A new software fix is currently in development and will likely be published in 01/2026. Replacing parts will not remedy the issue. For model series 243: The correction is already available. Perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

The instrument cluster display will remain operational. - No audio is present from the sound system - MBUX multimedia system (A26/17) may not be shown on the initial quick test - Various other MBUX multimedia system (A26/17) related complaints Cause Water ingress through the air vent under the front passenger seat (see attached, note that the vents are facing the rear of the vehicle). As a result, the head unit (A26/17) may become damaged. Inspect the MBUX multimedia system (A16/17) hardware, including all attached wiring and connectors, for traces of water and/or corrosion (see attached picture for example). Remedy Avoid using rubber floor mats for the second row seats on which water can collect and subsequently enter the air vent under the front passenger seat. An optimized cover is now available for the air vent under the front passenger seat (see parts note). To avoid a reoccurrence of water damage, install this cover. Note: Only primary losses resulting from the ingress of fluids that can be attributed to a production error is covered by the warranty. Fluids that are introduced into the vehicle as a result of environmental influences, incorrect repairs or incorrect use by the customer are not covered by the warranty. The damage code specified in this document only applies for the installation of the fan shroud.

P0CFE00 is stored in control unit "N83 - AC charger for high-voltage battery (SG-LG)". The fault message and the fault memory entry can also appear at the beginning of the charging pause during delayed charging. Both only occur in combination with active pre-entry climate control. Cause Software in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Remedy For model series 167, 214, 254 and 223 with code 802: Perform SCN coding in control unit "N83 - AC charger for high-voltage battery (SG-LG)". Please do not replace any parts even if the FC P0CFE00 coding continues to appear after successfully completing this step. A new software is currently in development and will become available in late 01/2026. Replacing parts will not remedy the issue. For model series 243: The correction is already available. Please inform the workshop to perform a software update and SCN coding for the control units "N116/5 - Direct current charging connection unit (DCCU)" and "N83/11 - AC charger for high-voltage battery (SG-LG)" in order to remedy the problem.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Coolant odor or leaking from coolant expansion reservoir. Cause Coolant wicking through electrical contacts, or level sensor electrical connections not present in expansion reservoir. Remedy **Important: If the coolant expansion tank is replaced due to leak at the level sensor contact area, ensure that the expansion tank is marked as the main damage part in the warranty claim 1- Inspect expansion tank level sensor electrical connection for missing contacts. Additionally the triangular sticker may not be present on top of reservoir. See example of OK and NOK part. Replace the expansion reservoir if contacts are found to be missing. A TIPS case is not needed. Proceed to step 3. 2- With contacts present, inspect coolant level sensor electrical connection for leakage past contact seals. Visible coolant at the connection indicates leakage. Capture photos if leakage is identified and create a TIPS case with the Powertrain team. Replace the expansion reservoir. 3- Repair any damage to wiring or electrical contacts on wiring harness from S41 to N10/6. Check the front SAM N10/6 for coolant contamination and replace if necessary. Inspect electrical connectors at base of A-pillar for contamination and repair/replace as necessary.

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: vehicle technical issue? customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: Amperage setting of charger and time battery was on charger XENTRY Battery Tester results Voltage of battery taken with multimeter: Do not connect charger while taking measurements N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) Workshop analysis of conspicuous data Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

U013281 - Communication with control unit "Suspension" has a malfunction. Incorrect data were received. C156F00 - The signal values of the level sensors are implausible. Cause Physical layer wiring to the level control sensors B22/X. Remedy Check A108/2 and A108/3 for freeze frame data section "ZF_error_handler". The text will provide a good place to start. Example: "SPC_FEHLER_VehLvl_Stat_HP_AMG_AR2_SNA_VehLvl_RR_V2_AMG" indicates the Right Rear may have initiated the DTC. See attached picture for reference. Use Hioki to measure wiring to all four level sensors. Use above DTC freeze frame data to inspect specific wiring. In some instances, level sensors may rectify concern although wiring to a different level sensor may be the cause. If vehicle exhibits concern after all of the above is completed, please open a TIPS case to the Body, Chassis, Entertainment Inbox.

and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Initial problem - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] - Delete fault memory and recheck vehicle Note - If wiring fault is found in newer vehicle, please send in a IFQ (Initial Field Quality) TIPS Case. 2. Subsequent problem after repair In this case, the workshop must perform the following operation steps: - Replace overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) - Clean electrical connectors of overhead control panel with commercially available contact cleaner and clean, purified compressed air. - Delete fault memory and recheck vehicle Note - If no remedy is found, please open a TIPS case and send to the Body/Chassis/Entertainment inbox.

OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: Hitting the curb/posts with the front wheels. Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). Cracks (1) High pressure cleaner (2) Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

236.17 due to a global supply constraint. 236.17 ATF 1L and 5L (PNs: A002989060312 and A002989060313) bottles are out of stock or in limited supply at Zep. This LI has been created with the following intention: - Provide dealers with additional workshop-focused guidance regarding the current ATF 236.17 supply constraint and the planned introduction of ATF 236.18. - Supplement existing communications and address common workshop questions related to maintenance, repairs, and fluid applicability. - Provide technical clarification and practical workshop guidance during the temporary supply constraint period. Dealers should continue to reference the latest News Channel Updates (NCUs) for the most current information regarding availability, ordering processes, supply status, and other related updates. Cause Damage to the Shell production facility has resulted in 236.17 oil supply being reduced to 50% of normal output until the end of 2026. Remedy Please first check Latest NCU updates for latest detailed information. Please continue placing orders through Paragon as normal. Supply is expected to remain reduced and allocation measures are currently in place. We ask for your patience through this restricted supply period. Most orders will be filled in the order in which they were received, as supply is replenished. Those dealers with zero inventory, and pending orders, will receive priority. We expect supply to be stabilized in September 2026. Approved Fluids: Only use transmission fluid from the approved list found on the Mercedes-Benz Operating Fluids website. Non-approved fluid will result in mechanical damage to the transmission and must be avoided. https://operatingfluids.mercedes-benz.com/sheet/236.17 Approved fluids can be claimed as follows if there is no Mercedes-Benz part number: Part # ATFSUB1L - TRANSMISSION FLUID 1 LITER ATFSUB5L - TRANSMISSION FLUID 5 LITER Dealerships with Zero Inventory AND Grounded Vehicles: If a vehicle is currently grounded for repair at your dealer due to no 236.17 inventory, we may be able to expedite your order. Please open a StarSupport ticket including the following information: (Parts Related Inquiry>National Accounts>Zep) LI document number Short explanation of repair needed for grounded vehicle Current days down of RO Maintenance and Service Interval Guidance Published maintenance intervals remain unchanged. Vehicles should continue to be maintained in accordance with the applicable maintenance schedule. This LI does not revise or extend any published maintenance interval requirements. If all required parts and materials are not available prior to scheduling or beginning a transmission service, dealers should consider postponing routine preventative transmission maintenance until the necessary parts become available. For vehicles that have not yet reached the applicable maintenance interval and do not exhibit transmission-related concerns, there is no need to recommend preventative transmission services prior to the scheduled maintenance interval. When evaluating whether routine transmission maintenance can be deferred until parts become available, dealers should consider: Overall vehicle condition Vehicle usage and operating conditions Presence of transmission-related symptoms or customer complaints Customer expectations and vehicle operating requirements Availability of required parts and materials Introduction of New Fluid Specification 236.18 Mercedes-Benz is currently preparing the introduction of ATF 236.18 as an additional approved transmission fluid solution for applicable NAG3 transmissions. At the time of publication of this LI, ATF 236.18 is not yet available for dealer ordering or workshop use in the U.S. market. See attachment for further details.

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CPR = Car Package Release (For MB.OS) CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465, 906 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).

Cause Software application. Remedy 1. Perform IPR and follow the instructions. 2. Perform software update on transmission control unit VGS2NAG3M (N15/15), available since 09/2025. (New software numbers) A0019021921 A0019022121 3. In Xentry, go to transmission control unit under Special Functions > Special Function: Reset Learned Values (Deceleration Mode). 4. Perform standstill adaptation. NOTE: All steps (software update, resetting learned values, and standard adaptation) must be completed to fully resolve the complaint.

Charging is interrupted after 15 minutes. Following malfunctions on Instrument Cluster (IC) can appear : "AC charging inoperative Consult workshop" "Performance severely limited Hybrid drive system The following fault codes related to the failure can be found in the below Control units : PTCU - N127 (Drivetrain control unit) P0667FA - On-board charger P0F7FFA - On-board charger OBL223_GEN4 - N83/11 (Alternating current charger for high-voltage battery): P0667FA - The internal temperature sensor of the control unit has a malfunction. P0F7FFA - The signals of coolant temperature sensors 1 and 2 of the on-board charger are implausible in comparison with each other. P0D8F97 - The cooling of the on-board charger is inadequate. The system function is restricted. INV1G40 - N147 (Power electronics control unit): P0A9300 - The cooling system for the low temperature circuit has a malfunction Cause The coolant lines of the LT1 (low temperature) cooling circuit for the power electronics (N147) and the LT2 (low temperature) cooling circuit for the AC charger (OBL), may have been installed in reverse order Remedy It is possible that the coolant hoses highlighted in the pictures are installed in reverse order. Interchange these two coolant lines and check if the vehicle is charging without any malfunction.

It may be mistaken for a hard brake engagement Cause In certain driving scenarios, the transmission torque adaptation for the 5-4 downshift is recorded at a higher value. This skews the learning which leads to harsh engagement of the B06 clutches, creating the harsh 5-4 downshift. Remedy "Phase 1" software was released 11/14/2024 to slow the adaptation process and reduce the frequency of the complaint. However, it was possible that the clients driving style could cause suboptimal adaptations, and this would result in the concern returning sooner than anticipated for some vehicles. "Phase 2" software has been released as of 09/04/2025 and will correct the root cause of the poor adaptation learning. See software list below. A0019021721 A0019021821 A0019021921 A0019022021 A0019022121 Please follow IPR recommended procedures. IPR has been trained to recognize this pattern and will advise the necessary steps below. ***ALL STEPS MUST BE PERFORMED! *** The concern will still be present or may return if not completely correctly. Ensure all steps are documented in paperless, the previous warranty print out with the check marks is no longer required. 1. Perform resetting of learned values "deceleration mode" (VGS > Special Procedures > Special procedure > Resetting learned values Deceleration mode) 2. Perform 5 standstill adaptions in a row followed by 5 torque converter adaptations 3. Perform software update for the VGS Control Unit 4. Clear all faults 5. Perform final QC test drive & confirm normal operation of all shifts If issues arise during the process or the concern has returned with phase 2 software, please submit a TIPS case to the Powertrain inbox with the following information: - Initial Quick Test w/ freeze frame data - VGS Control Unit Log - Initial EEPROM data (before any procedures) - Current EEPROM data (after LI/IPR procedures) - Relevant screenshots (standstill adaptations, software update, etc)

It may be mistaken for a hard brake engagement Cause Poor learning of brake B06 adaptation values over time. Remedy Short-term remedy: 1. Perform IPR and follow the instructions. 2. Perform resetting of deceleration values (VGS > Special Procedures > Special procedure > Resetting learned values Deceleration mode) 3. Perform standard adaptation 4. Reevaluate the concern and release vehicle if no longer present Note: ALL steps (resetting learned values and standard adaptation) must be completed to fully resolve the complaint. Long-term measure: Aftersales software is currently in development.

It may be mistaken for a hard brake engagement Cause In certain driving scenarios, the transmission torque adaptation for the 5-4 downshift is recorded at a higher value. This skews the learning which leads to harsh engagement of the B06 clutches, creating the harsh 5-4 downshift Remedy "Phase 1" software was released 11/14/2024 to slow the adaptation process and reduce the frequency of the complaint. However, it was possible that the clients driving style could cause suboptimal adaptations, and this would result in the concern returning sooner than anticipated for some vehicles. "Phase 2" software has been released as of 09/04/2025 and will correct the root cause of the poor adaptation learning. See software list below. (format: Hardware - Old SW >> New SW) A0009011705 - A0019021614 >> A0019021721 A0009011705 - A0019021914 >> A0019021821 A0009011705 - A0019021714 >> A0019021921 A0009011705 - A0019022014 >> A0019022021 A0009011705 - A0019021814 >> A0019022121 Please follow IPR recommended procedures. IPR has been trained to recognize this pattern and will advise the necessary steps below. ***ALL STEPS MUST BE PERFORMED TO REMEDY THE CONCERN*** As of 03/06/2025 ALL warranty claims must include a print out of the IPR screen showing a check mark next to each required step as an indication that all steps have been completed in order to be approved and paid. See attached example of needed IPR screenshot 1. Perform resetting of learned values "deceleration mode" (VGS > Special Procedures > Special procedure > Resetting learned values Deceleration mode) 2. Perform 5 standstill adaptions in a row followed by 5 torque converter adaptations 3. Perform software update for the VGS Control Unit 4. Clear all faults 5. Perform final QC test drive & confirm normal operation of all shifts If issues arise during the process or the concern has returned with phase 2 software, please submit a TIPS case to the Powertrain inbox with the following information: - Initial Quick Test w/ freeze frame data - VGS Control Unit Log - Initial EEPROM data (before any procedures) - Current EEPROM data (after LI/IPR procedures) - Relevant screenshots (standstill adaptations, software update, etc)

Howling in overdrive mode around 5th gear. Models 167.1/3 and 167.9 up to 03/2022 (except 167.987) occurs between 40-50mph Model 167.987 up to 03/2022 occurs between 55-65mph Cause Unfavorable overlapping of vibrations between drivetrain and rear axle carrier at different speeds and selected drive range. Remedy Install additional vibration damper at front axle subframe suspension of rear axle. For basic data, see AR35.10- P-0044ME Note: Chamfer at vibration damper must be between axle subframe suspension and rear axle carrier (see attachment)

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not preauthorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

generated by a micromovement on the contact surface between the rim and the brake disk (wheel bolt group) and may be intensified by potential soiling. The more lightweight rim (AMG forged rim) transmits the noise louder; in the case of cast rims, the noise is generally not perceptible. This is not a technical defect, but rather a complaint concerning comfort. Safe operation of the vehicle is ensured at all times. Remedy Important note: The operations described below do not represent a permanent remedy in every case. The noise may reoccur again after an indefinite period of time; sanding the rims with abrasive media multiple times is not permissible. Only cleaning using the Hazet tool 4960-160 (recommendation) can be performed without any concerns each time the wheel is changed or if the complaint reoccurs. Replacing the parts (rim, wheel bolts, wheel bearings, wheel hub, brake disk) is not expedient in the event of this complaint. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Clean the components of the wheel bolt connection according to the WIS instructions Sand down the rim and brake disk bowl by performing the following steps: Manually sand rim (old design only) in area of water drain bores (Figure 1; item A), approx. 1.5 cm left and right of water drain bore (Figure 2) Note: Use abrasive paper with grit size 80. The grooving in this area should no longer be visible (sand down approx. 0.1-0.2mm) Also sand brake disk bowl using emery cloth or abrasive paper with a grain size of 120 For vehicles equipped with the AMG ceramic brake system (B07), abrasive paper may not be used for cleaning on the brake disk side Note: Do not use any cleaning agent when cleaning on the rim side. Cleaning using abrasive paper with a grain size of 80 will suffice. Do not apply any grease, lubricant or paste after cleaning The brake disk bowl should be "bare metal" in the area of the imprints made by the hole (Figure 3)

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Vehicle production date prior to December 2025. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Vehicle production date prior to December 2025. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Axle Half Shaft noise when changing direction - Front) LI33.30-P-056665 (Axle Half Shaft noise when changing direction - Rear) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Vehicle production date prior to December 2025. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Lane Keeping Assist, Blind Spot Assist, Adaptive Brake Assist, and/or ATTENTION ASSIST may be temporarily unavailable. The brake system continues to operate with normal effectiveness. The support functions listed may be unavailable, but are available again after an ignition off/on cycle.</p><p>One or more of the faults listed under 'Control unit/ fault code' for the accelerator pedal (B37) is logged in the PTCU control unit (N127). Consequential faults may have been logged in the ESP control unit.</p> Cause <p>Resistance at accelerator pedal contacts.</p> Remedy <p>The remedy refers only to the model series listed and is not compatible with other published TIPS documents for other model series.</p><p>If all the test steps stored in XENTRY Diagnosis have been performed and no component faults were found, the following work must be carried out:</p><p>- Replace the connector/ feed line to the accelerator pedal sensor (B37) using the wiring harness repair kit (see parts table).</p><p>Please ensure that the twisted lines are untwisted as little as possible.</p><p>Please do not replace any other components (e.g. accelerator pedal sensor).</ p><p> </p><p>Reoccurrence of the problem:</p><p>If the fault occurs again, or if this is a reoccurrence of the same problem, please make sure that the line connectors between the repair wiring harness and the interior wiring harness are fitted correctly and that the solder has dispersed evenly. In case of doubt, please repeat the repair. If the problem reoccurs after the second repair attempt, please create a TIPS case with informative photos of all line connectors.</ p><p> </p><p>Information on alternative to repair wiring harness:</p><p>If there should be any supply bottlenecks with regard to the repair wiring harness, then the contact sockets on the accelerator pedal sensor can be replaced as an alternative.</ p>

function).</p><p>The result is a constant beep tone because no valid finger is detected and therefore no corresponding user profile can be assigned. </p> Cause <p>Software bug in A105 touchpad (TPAD).</p> Remedy <p>Perform software update in A105 touchpad (TPAD).</p>

Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify.

generated by a micromovement on the contact surface between the rim and the brake disk (wheel bolt group) and may be intensified by potential soiling. The more lightweight rim (AMG forged rim) transmits the noise louder; in the case of cast rims, the noise is generally not perceptible. This is not a technical defect, but rather a complaint concerning comfort. Safe operation of the vehicle is ensured at all times. Remedy Important note: The operations described below do not represent a permanent remedy in every case. The noise may reoccur again after an indefinite period of time; sanding the rims with abrasive media multiple times is not permissible. Only cleaning using the Hazet tool 4960-160 (recommendation) can be performed without any concerns each time the wheel is changed or if the complaint reoccurs. Replacing the parts (rim, wheel bolts, wheel bearings, wheel hub, brake disk) is not expedient in the event of this complaint. Clean the components of the wheel bolt connection according to the WIS instructions Sand down the rim and brake disk bowl by performing the following steps: Manually sand rim (old design only) in area of water drain bores (Figure 1; item A), approx. 1.5 cm left and right of water drain bore (Figure 2) Note: Use abrasive paper with grit size 80. The grooving in this area should no longer be visible (sand down approx. 0.1-0.2mm) Also sand brake disk bowl using emery cloth or abrasive paper with a grain size of 120 For vehicles equipped with the AMG ceramic brake system (B07), abrasive paper may not be used for cleaning on the brake disk side Note: Do not use any cleaning agent when cleaning on the rim side. Cleaning using abrasive paper with a grain size of 80 will suffice. Do not apply any grease, lubricant or paste after cleaning The brake disk bowl should be "bare metal" in the area of the imprints made by the hole (Figure 3)

Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2 3 key cycles. The vehicle can be released back to the customer.

Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 23rd, 2026. After July 23rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

Cause Signal timing error. Remedy 167: SW has been released. Update the FSAM to the latest SW version. 465, 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

Cause Signal timing error. Remedy 167: SW has been released. Update the FSAM to the latest SW version. 465, 290: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, June 11, 2026. After June 11th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

The deadline for all dealer returns is no later than Thursday, June 4, 2026. After June 4th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

movement of the wiper on the driver's side or front passenger side (see Figure 1). Cause During replacement of worn wiper blades, the wrong blades were installed, contrary to the specifications. Left-hand drive vehicle: Incorrect: A1678209201 Correct: A1678208703 The standard wiper system from model series 167 was changed in October 2022. The wiper arms of the standard system after the switchover have a higher clamping force and are not compatible with the wiper blades before the switchover. The wiper lip of a wiper blade before switchover is deformed due to the higher contact pressure of the wiper arm, which can result in a 510 cm wide strip in the area of the wiper blade attachment not being fully wiped. Identification of the wiper blades installed on the vehicle: Wiper blades for vehicles up to October 2022 have a clip between the connector and the end of the blade Wiper blades for vehicles produced from October 2022 onwards do not have a clip between the connector and the tip of the blade See Picture 2 Note: The correct wiper blades were installed on the vehicle at the factory. This does not constitute a defect attributable to the manufacturer. Remedy Install the correct wiper blades intended for the vehicle

The deadline for all dealer returns is no later than Thursday, April 23, 2026. After April 23rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

movement of the wiper on the driver's side or front passenger side (see Figure 1). Cause During replacement of worn wiper blades, the wrong blades were installed, contrary to the specifications. Right-hand drive vehicle: Incorrect: A1678209301 Correct: A1678208803 The standard wiper system from model series 167 was changed in October 2022. The wiper arms of the standard system after the switchover have a higher clamping force and are not compatible with the wiper blades before the switchover. The wiper lip of a wiper blade before switchover is deformed due to the higher contact pressure of the wiper arm, which can result in a 510 cm wide strip in the area of the wiper blade attachment not being fully wiped. Identification of the wiper blades installed on the vehicle: Wiper blades for vehicles up to October 2022 have a clip between the connector and the end of the blade Wiper blades for vehicles produced from October 2022 onwards do not have a clip between the connector and the tip of the blade See Picture 2 Note: The correct wiper blades were installed on the vehicle at the factory. This does not constitute a defect attributable to the manufacturer. Remedy Install the correct wiper blades intended for the vehicle

Cause Signal timing error. Remedy This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer. There is software in development for this concern.

Cause Delamination of film on carrier plate. Remedy Additional replacement part numbers have been approved for the affected model series V/C/X167, X294 and X296.

(see attachment) Cause The cause is currently being investigated. Remedy Update the HU7 to the latest software version, then perform a factory reset of the HU7. Steps to perform factory reset: Navigate to Settings > System > Reset > Reset to factory settings and confirm If the problem persists, please record HU7 log and also a trace of the Body CAN (For Star 2 Body Can 1 and for Star 3 Body Can 2) during the symptom and send via a TIPS case to the Body/Chassis/Entertainment inbox. Note: Only collect and submit the log and trace if the symptom can be reliably reproduced.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

TIREFIT sealant bottle may not meet specifications. The possibility exists that the sealant bottle may leak or may have otherwise been removed from the vehicle. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk.

(see attachment). Cause The cause is currently being investigated. Remedy Update the HU7 to the latest software version, then perform a factory reset of the HU7. Steps to perform factory reset: Navigate to Settings > System > Reset > Reset to factory settings and confirm. If the problem persists, please record HU7 log and also a trace of the Body CAN (For Star 2 Body Can 1 and for Star 3 Body Can 2) during the symptom and send via a TIPS case to the Telematics team. Note: Only collect and submit the log and trace if the symptom can be reliably reproduced.

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Cause Internal tolerances of the electric rollbar. Remedy 1. Confirm front or rear roll bar. 2. Remove the affected sway bar links and carefully drive vehicle. Noise not resolved with sway bar links removed > Not appliable to this LI, noise is from a different component. Noise resolved with sway bar links removed > Current parts may make some noise and is currently state of the art. Optimized, quieter parts will be available Q4 2026, please release vehicle until such time parts are available. For further questions, inquiries, or sound levels approximately equal to or above what is shown in the attachment, open a TIPS case to the Body, Chassis, Entertainment inbox.

Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: Fluid intrusion Broken bushings or physical damage See attachments. Remedy If a component needs replacement but shows no visible external damage, submit a detailed TIPS case only when technical support is required. Include details of all connected external devices (such as charging cables, USB drives, and hard drives). If diagnostic results directly indicate component replacement, a TIPS case is not necessary.

Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: Fluid intrusion Broken bushings or physical damage See attachments. Remedy If a component needs replacement without visible external damage, submit a detailed TIPS case. Include information on all connected external devices (e.g., charging cables, USB drives, hard drives).

Cause Many possible root causes Remedy *Note - This Li does not apply if there are other Li's that apply to your concern OR you have a fault and/or guided test that leads to a root cause. AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements (Template attached to be used for submission of Warranty claim and/or TIPS case) Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements Cooling Capacity Test (If System Has a Charge) Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs - Warranty Submission Requirements on the Repair Order Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found

to: Summer heat Direct sunlight Lack of air conditioning or ventilation Camera enters self-protection mode to prevent overheating. Remedy Do NOT replace any parts. The driver camera (NTG7: MDC295; CIVIC.i2: CIVIC206) is operating as designed. Allow the interior to cool down. If the message remains after cooling: Run XENTRY Diagnosis Check latest software for Actuation of Driver Camera (A26/17) No TIPS case required.

Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

and play them with Windows Media Player. Cause Driving with summer tires in combination with low outside temperatures. At low outside temperatures or in wet conditions, a noise may be produced at the outer wheel on the front axle while maneuvering with sharp steering angles. Note: AMG vehicles with 4MATIC of model series 217 (without code 494) and model series 222 have a modified axle geometry compared with series production vehicles to provide more sporty handling. The problem cannot be remedied by changing the axle settings.

TIPS case with the below information and send to the Body/Chassis/Entertainment Inbox: Open the flap and take a detailed photo of the fuel tank strap attached at the hinge arm. Is the attachment bent or kinked? Are there pressure marks in the recess where the retaining strap is located when closed? Check position of the fuel tank strap in the closed state - is it being pinched? Check if the clipping is correct to see if the attachment surfaces are damaged. Removal of the recess to check the seal whether it is folded down. Detach the fuel tank strap from the fuel filler neck at the hinge arm and place it in the recess, then close the flap again and check the protrusion. Is the protrusion better? Does the flap open with less force?

TIPS case with the below information and send to the Body/Chassis/Entertainment Inbox: Open the flap and take a detailed photo of the fuel tank strap attached at the hinge arm. Is the attachment bent or kinked? Are there pressure marks in the recess where the retaining strap is located when closed? Check position of the fuel tank strap in the closed state - is it being pinched? Check if the clipping is correct to see if the attachment surfaces are damaged. Removal of the recess to check the seal whether it is folded down. Detach the fuel tank strap from the fuel filler neck at the hinge arm and place it in the recess, then close the flap again and check the protrusion. Is the protrusion better? Does the flap open with less force?