2017 Mercedes-Benz AMG GLE43 TSBs

and 725.1 (NAG3 facelift/9GTRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the ongoing quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 Classic AMG sport model (AMG 43 and AMG 53 with converter, automatic transmission 725.0) NAG3 Classic Hybrid (automatic transmission 725.0) NAG3 Classic AMG 63 (automatic transmission 725.0) NAG3 MOPF ISG2 (automatic transmission 725.1) NAG3 MOPF Hybrid (automatic transmission 725.1) NAG3 MOPF AMG sport model (AMG 53/AMG 53e with ISG48V2 & converter /hybrid, automatic transmission 725.1) NAG3 MOPF AMG 43/63 with engine 139/177 (automatic transmission 725.1) Steps for the Service Advisor: Important: The more information and detail that can be given to the workshop about the complaint, then the more effective the subsequent diagnosis with IPR can be. To this end, a detailed service reception questionnaire has been provided to help the Service Advisor ask the right questions about the complaint. Ask precise details about the customer complaint and the conditions and context. Fill out the service reception questionnaire (please see WIS document: OF27.00P300005A) for customer complaints in detail and forward it to the workshop. Operation steps for the workshop employee: 1. Perform quick test 2. Access the transmission control unit via XENTRY Diagnosis 3. Select "A customer complaint has been received" and carry out all subsequent operation steps (IPR diagnosis path). 4. The IPR repair instructions are displayed, Carry out the IPR repair instructions without performing any further diagnostic or repair steps. Important: The IPR repair instructions are binding and must be carried out. Differing repairs are possible; such repairs must be documented in XENTRY in free text. Please observe the information regarding the IPR diagnosis process in XENTRY. Conventional diagnosis and subsequent appropriate repairs are only permitted if IPR does not specify any repair instructions. Invoicing for the guided IPR steps: Operation item 270640 and 0.1 hours Notice regarding warranty: The use of IPR in association with warranty claims is mandatory! If the IPR repair instructions are disregarded without justification, the warranty claims may be rejected and/or are subject to debit. IPR will provide a measure to repair the vehicle based on various data sources (EEPROM, fault codes, etc). Please consider the vehicle maintenance record of the vehicle. For warranty and goodwill repairs, the transmission ECU test log and/or IPR test result must be uploaded into Paperless XENTRY Diagnosis (pXD) . If repair is being determined based of oil pan condition pictures of oil pan MUST be provided to warranty as justification. Tamperproof documentation: The IPR repair instructions are stored in the control unit log. Please file this document in a tamperproof manner either in digital form or as a hardcopy printout and also enclose a printout with the damaged part. In this regard, please comply with the countryspecific warranty requirements of the MPC/general distributor.

This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 Allwheel drive (ARS) N127 'Drivetrain' (PTCU) control unit Y3/8 Transmission control for 9gear transmission (VGS) N3/10 Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications Collect an oil sample of the original fluid 5. Complete all transfer case Techin processes located under VG Control Unit > Adaptations Resetting the oil service data Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature (>60C ) 6. Operate vehicle in full circle with steering at full lock 5x to the left 5x to the right Return the vehicle to the client and request they drive the vehicle for at least 200 miles and return if the concern is not resolved. The extended drive will ensure the clutches are properly conditioned with the new oil and should resolve the concern. If this LI has already been applied to the vehicle, please submit a TIPS case to the Powertrain inbox with the following information: Initial quick test with fault freeze frame data Initial transmission EEPROM data VGS and Transfer Case Control Unit Log (N45 or N15/7) Special Acquisition Data .txt file (Transfer Case Control Unit > Special Procedures > Procedures for support queries to market support > Special Data Acquisition) Photo of the original oil condition What color was the fluid drained from the transfer case before the oil change? Was an oil sample collected, and can you provide a photo of the original fluid? What color and part number fluid was used during the oil change? How far was the vehicle driven after?

and 725.1 (NAG3 facelift/9GTRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the ongoing quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 AMG sports models (AMG 43 and AMG 53 with converter) NAG3 AMG 63 NAG3 Hybrid NAG3 Facelift (automatic transmission 725.1) NAG3 facelift (725.1) with engine 139/177 (AMG 43/63) Steps for the Service Advisor: Important: The more information and detail that can be given to the workshop about the complaint, then the more effective the subsequent diagnosis with IPR can be. To this end, a detailed service reception questionnaire has been provided to help the Service Advisor ask the right questions about the complaint. Ask precise details about the customer complaint and the conditions and context. Fill out the service reception questionnaire (please see WIS document: OF27. 00P300005A) for customer complaints in detail and forward it to the workshop. Operation steps for the workshop employee: Perform quick test Access the transmission control unit via XENTRY Diagnosis Select "A customer complaint has been received" and carry out all subsequent operation steps (IPR diagnosis path). The IPR repair instructions are displayed. Carry out the IPR repair instructions without performing any further diagnostic or repair steps. Important: The IPR repair instructions are binding and must be carried out. Differing repairs are possible; such repairs must be documented in XENTRY in free text. Please observe the information regarding the IPR diagnosis process in XENTRY. Conventional diagnosis and subsequent appropriate repairs are only permitted if IPR does not specify any repair instructions. Invoicing for the guided IPR steps: Operation item 270640 and 0.1 hours !!!!! Notice regarding warranty: !!!!! The use of IPR in association with warranty claims is mandatory! If the IPR repair instructions are disregarded without justification, the warranty claims may be rejected and/or are subject to debit. IPR will provide a measure to repair the vehicle based on various data sources (EEPROM, fault codes, etc). Please consider the vehicle maintenance record of the vehicle. For warranty and goodwill repairs, the transmission ECU test log and/or IPR test result must be uploaded into Paperless XENTRY Diagnosis (pXD) . If repair is being determined based of oil pan condition pictures of oil pan MUST be provided to warranty as justification. Tamperproof documentation: The IPR repair instructions are stored in the control unit log. Please file this document in a tamperproof manner either in digital form or as a hardcopy printout and also enclose a printout with the damaged part. In this regard, please comply with the countryspecific warranty requirements of the MPC/general distributor.

Cause Frictional vibrations Remedy The intent of this document is to reduce noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some scenarios are normal and some are induced by driving style like those listed below: Driving style such as two footed driving where the pad might be in constant contact with the rotor. Brake pressure and application style (stopandgo traffic with consistent light brake pressure riding brakes where the brakes cannot cool sufficiently between applications). This can cause the brake pads to glaze and have a smooth/glassy surface which can induce noise. When ambient temperatures rise during summer peak and during cooling and cold winter months. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 34 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to reassessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the pistonside brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and reapply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper /carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the pistonside brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off

It will also ensure that if a case is necessary, all supporting documentation is available. This should not be used on its own as justification for creating a TIPS case. Cause The root cause will vary depending on the complaint. The goal of this document is to provide diagnostic checks and procedures that may help resolve customer complaints without opening a TIPS case. Remedy Before opening a transmission-related TIPS case, the following steps must be performed to ensure all relevant data has been collected and possible remedies (when applicable) have been performed. Please Note: At minimum, the documents below must be collected before proceeding to ensure the data in its original state when the vehicle arrived is captured. - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - Initial EEPROM data (.txt format) - IPR Result (if applicable. See LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool) - Transmission Heath Page If the vehicle has previously been repaired for the same concern, note the date, mileage, and TIPS case or RO number, along with a brief description of the prior work performed. IPR Guidance: The IPR recommended repair should be completed prior to following any steps in this LI and prior to case creation. IPR repairs do not require additional warranty approvals or a TIPS case to validate/confirm the results. To ensure efficient case handling, please avoid opening TIPS cases for this reason. For further information regarding IPR please see the following documents: LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool Oil Pan Condition Evaluation: In some situations, IPR will advise checking the oil pan condition and determining a repair based on the evaluation. Example photos in Xentry can be found in two ways: Use the blue hyperlink in the IPR result, and it will take you to the Condition check of transmission oil Navigate to Xentry Bluebook > Help for control unit > Condition check of transmission oil If a different repair that what is recommended by IPR is performed, attaching photo documentation of the complaint vehicle oil pan and the IPR example to the claim is required. Reproducing the Concern: Proper evaluation of transmission concerns generally requires the condition to be reproducible. It is recommended to compare the vehicle to a similar model, if available, to help determine whether the shift behavior is characteristic of the drivetrain or uncharacteristic for the vehicle. If the concern cannot be duplicated: A test drive with the customer may assist in understanding and reproducing the complaint. The vehicle shift quality should be compared to a known-good vehicle with identical drivetrain and model year. Check Shift Quality History (VGS Control Unit > Adaptations > Shift Quality History) Shift Quality History will show the last 5 noticeable harsh shifts and some of the parameters in which it occurred. You can use this to attempt recreation of the operating conditions and increase likelihood of reproducing the complaint. Complaint A: Shift Quality Note: Certain AMG variants may exhibit more firm and noticeable shift behavior as a normal characteristic. Refer to LI27.60P075147 for additional information. 1. Perform Valve flushing procedure 2. Perform 5 Torque Converter adaptions in a row - Allow the vehicle to warm up naturally, DO NOT power brake as it will increase the temperature in the torque converter. - After the 5th adaptation, collect a screen shot showing all 5 on one page 3. Perform a standstill adaption - collect a screen shot Recheck vehicle operation. If the concern has not improved, driving adaptations should be performed to target specific gear shifts.

Whats Included In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz is extending the warranty of the engine control unit software for fault codes related to the outside temperature sensor for the affected vehicles to a total of 10 years or 120,000 miles (whichever occurs first) from the vehicles original New Vehicle Limited Warranty start date. This addendum to the ECU software coverage applies to the vehicle regardless of ownership. This warranty extension only covers updates of the engine control unit (ECU) software to resolve faults related to the outside temperature sensor. The following vehicles are included:

2018 Mercedes-Benz vehicles listed below, the engine control unit (ECU) software may not meet current specifications. In certain circumstances when the vehicles are parked for a long duration, an erroneous activation of the Check Engine Lamp for the outside temperature sensor might occur. In our continuing efforts to assure the proper performance of Mercedes-Benz products and to ensure the satisfaction of our customers, the warranty for the ECU software in the subject vehicles has been extended from the original 4 years/50,000 miles to 10 years/120,000 miles. This ECU software extended warranty is applicable to the following vehicles: In the event of an illuminated Check Engine Lamp which leads to a diagnosis of a fault with the outside temperature sensor, the following fault codes may be present: Motor Electronics (ME) N3/10 P007128 (for M274/276LA engine) Ambient Air Temperature Sensor Circuit A Range/Performance signal bias level out of range/zero adjustment failure or ME N3/10 P007028 (for M270 engine) Ambient Air Temperature Sensor Circuit A signal bias level out of range/zero adjustment failure In this event, guided tests will be available in Xentry which will lead to the update of the engine control unit software. The following damage codes may be used: 54 575 90 Update Engine Control Unit Software. Please check the VIN in Netstar/VMI before scheduling the appointment for the repair. Applicable vehicles will display an extended warranty service package in Netstar/VMI on March 12, 2019. After the distribution of this NCU, a letter will be sent to owners of certain vehicles informing them that the warranty for the ECU software for fault codes related to the Outside Temperature Sensor will be extended from the original 4 years/50,000 miles to a total of 10 years or 120,000 miles (whichever occurs first). If customers have already paid to have the outside temperature sensor replaced, they may be eligible for reimbursement. Please advise the customer to follow the instructions detailed below (also included in a copy of the customer letter).

Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% a negative charge balance A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked). Vehicles with code B01+801: When charging while stationary, the 48V battery must have a state of charge (SOC) of 70% before the 12V primary battery, or the secondary battery in the case of code 503, can be charged. To ensure optimum battery care, please also comply with the existing Service Information documents regarding the handling of stock vehicles (SI54.10-P-0024A) and on remaining in transport mode (SI54.00-P-0004A) until immediately before handover to end customers. Special note: Do not replace any parts, if the message has occurred due to battery discharge as a result of the driving profile or the ignition being switched on (see attached examples); in such cases separate warranty and goodwill invoicing is not possible, as this is a normal on-board electrical system protection function. Likewise battery care and recharging do not qualify as a W&G case. Please advise customers accordingly regarding the above-mentioned issues relating to vehicle use.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. **NOTE - As of Sept 2025 the pressure testing tool is not finalized and may require modifications to fit properly. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

'A' has a short circuit to positive stored in VGS control unit. Cause Electrical failure of oil pressure sensor integrated into VGS Control Unit Remedy Intelligent Predictive Repair (IPR) recognizes this fault pattern and will provide the necessary repair suggestion. 1. Perform IPR and follow the recommended procedures 2. Replace complete EHS valve body, fill to near max fluid level, & complete initial start-up - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement.

This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications - Collect an oil sample of the original fluid 5. Complete all transfer case Tech-in processes located under VG Control Unit > Adaptations - Resetting the oil service data - Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature ( >60C ) 6. Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Return the vehicle to the client and request they drive the vehicle for at least 200 miles and return if the concern is not resolved. The extended drive will ensure the clutches are properly conditioned with the new oil and should resolve the concern. If the concern continues to occur with the control unit disconnected or after the above steps have been performed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial quick test with fault freeze frame data - Initial transmission EEPROM data - VGS and Transfer Case Control Unit Log (N45 or N15/7) - Photo of the original oil condition - What color was the fluid drained from the transfer case before the oil change? - Was an oil sample collected, and can you provide a photo of the original fluid? - What color and part number fluid was used during the oil change? - How far was the vehicle driven after?

the vehicle is stationary and ECO Start/Stop is active (combustion engine is off). The noise is more noticeable outside the vehicle and in acoustically shielded areas such as closed rooms or garages. Cause The noise in the valve body (EHS) is caused by superimposed pressure peaks acting on the valves. This phenomenon occurs only after a certain running-in period due to the influence of micro-contamination in the valve bores. Remedy A hardware modification of the electro-hydraulic control unit (EHS) is currently being implemented (no change to the part number). This will be incorporated into series production and as a spare part starting from 12/2025. This is only a comfort-related complaint and has no impact on the functionality or service life of the transmission. For sensitive customers, the following measures can be performed: 1. Replace the electro-hydraulic control unit (EHS), the oil pan, and the transmission fluid. - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement. (See attached location guide)

EEPROM or Transmission Health system following the replacement of the below components: - The electrohydraulic control unit (EHS valve body) in transmission 725.0/725.1 - The repair kit for the control unit (VGS) in transmission 725.0 Cause Missing, incorrectly installed, or damaged guide tubes on the EHS valve body. Remedy Check for the correct installation of the guide tubes (refer to attachments under Cause), correct installation if necessary. Parts Catalog References: NAG3M 725.1 AND NAG3C 725.0 (AMG only): Part numbers 100, 120, 150, 160 NAG3C 725.0 (Non AMG): Part numbers 280, 290, 330, 340 NOTE: If any of these guide tubes are not installed and the vehicle is driven, it will create several rinse and slipping events in the EEPROM data. These values caused by incorrect installation need to be erased to prevent future misdiagnosis. Submit a TIPS case to the Powertrain inbox with the following to receive the necessary reset password: - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - IPR Result - Initial EEPROM data (before repairs) - Latest EEPROM data - Photo of oil level ultrasonic measurement next to XENTRY specifications Please provide detail regarding the reasoning for the initial replacement in your workshop findings and measures performed. (This topic was covered in the July 2022 and July 2024 Passenger Car Tech Topics)

This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications - Collect an oil sample of the original fluid 5. Complete all transfer case Tech-in processes located under VG Control Unit > Adaptations - Resetting the oil service data - Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature ( >60C ) 6. Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right 7. Perform an extended 200mi road test to ensure the clutches are properly conditioned with the new oil. 8. Reassess the concern and release the vehicle if no longer present. If the concern continues to occur with the control unit disconnected or after the above steps have been performed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial quick test with fault freeze frame data - Initial transmission EEPROM data - VGS and Transfer Case Control Unit Log (N45 or N15/7) - Photo of the original oil condition - What color was the fluid drained from the transfer case before the oil change? - Was an oil sample collected, and can you provide a photo of the original fluid? - What color and part number fluid was used during the oil change? - How far was the vehicle driven after?

Cause In the groove where the pan seal is placed, there may be imperfections (porosity) in the casting causing fluid to leak past the seal. The supplier states this only affects rear differentials with 2023 production date. The production date can be found stamped on the housing cover (see attachment). Remedy 1. Follow the attached instructions to inspect the rear differential cover for porosity. 2. Repair the vehicle with the applicable repair kit for the chassis. - The new oil pans that come with the repair kit should be produced in 2024 and not have this issue. *When submitting the claim, please reference this LI document and if porosity was found.*

and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

Oil discoloration is present during oil change (water in oil) 3. Oil leakage from the breather cap Cause The bleed line of rear differential may be misaligned, causing the rubber end pieced to rest on the wheel well liner. When driving in the rain, water enters through the rubber elbow from the soaked wheel well liner. Remedy Perform a road test and determine the location of the noise using NVH equipment. If the rear axle differential is the root cause of the noise, continue with the following: 1. Drain oil from rear axle differential and check for signs of water intrusion (discoloration/cloudiness) Remedy A: If no water is found 2. Remove/install left wheel well trim. 3. Remove rubber end piece from the bleed line. 4. Install modified end piece with the part number A 167 351 50 00. 5. Identify source of the noise and, if necessary, replace the parts causing the concern. Remedy B: If water is found 2. Remove/install left wheel well trim. 3. Remove rubber end piece from the bleed line. 4. Install modified end piece with the part number A 167 351 50 00. 5. Replace rear axle differential

Cause Frictional vibrations Remedy The intent of this document is to reduce or eliminate noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some of the scenarios are: Driving style Brake pressure and application style (stop-and-go traffic with consistent low brake pressure riding brakes where the brakes cannot cool sufficiently between applications). Ambient temperatures 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and re-apply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake application

Cause Frictional vibrations Remedy The intent of this document is to reduce or eliminate noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some of the scenarios are: Driving style Brake pressure and application style (stop-and-go traffic with consistent low brake pressure riding brakes where the brakes cannot cool sufficiently between applications). Ambient temperatures 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and brake paste as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". If adhesive is already installed on backing plate, you may gently scrape off and re-apply a new adhesive. In some instances the adhesive may be very carefully removed and Molykote applied instead. 4. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 5. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 6. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. e) Finally drive approx. 3 miles to allow the system to cool. f) Reassess noise.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". 5. Apply heat-resistant lubricating paste to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 6. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. e) Finally drive approx. 3 miles to allow the system to cool. f) Reassess noise.

Cause Silicate granulate may have escaped from a damaged bag in the expansion reservoir (not visible), reducing the coolant flow in the heater heat exchanger (see picture). Remedy With the aforementioned complaint, make sure that the cooling circuit is inspected for silicate residues after all standard tests are completed. The silicate residues tend to accumulate upstream of the shutoff valve for the heater hot water pulsed valve. If there are silicate residues in the coolant, the engine must be flushed thoroughly. To make sure that all silicate residues are removed from the cooling circuit, the following parts must also be replaced (cleaning of these components is not sufficient): Coolant expansion reservoir, radiator, oil/water heat exchanger (oil cooler), heater valve, heat exchanger of heater, coolant and, if installed, the electric water pump for the residual heat utilization system. Determine the parts for the respective vehicle in the EPC.

parking See video for example Cause Noise originates within the transmission valvebody Remedy Take a video from underneath vehicle recording the noise Pull EEPROM data, Inital Quick Test, and Control Unit Log Please open a TIPs case providing all data to assess next steps.

incorrectly Remedy Adjustment of the windows or window guides as specified in AR72.10-P-1960GQS . A video with further information on instructions can be found in the attachment. Description of the videos: Safety Information: 1. AS00.00-Z-0011-01A Risk of injury with trapped or crushed fingers when performing removal/installation and adjustment work on hoods, doors, lids and sliding roof 2. AH67.00-P-0003-01FB Notes on avoiding damage to glass and windows of special protection vehicles Work Procedures: 1. Connect the operating switch to the door wiring harness and partially raise the window (not illustrated) 2. Slacken and remove the upper nuts on both spacers 3. Carefully lift the window off the spacer and move it towards the rear against the rear window guide 4. Lower the window again and check the offset between the spacer and the mounting holes at the rear and front 5. Adjust the mounting at the rear - The window must lie parallel against the rear guide along its entire length - Undo the fasteners of the bracket on the window lifter - Align the bracket with spacer to the bore in the window mounting, first in the longitudinal direction and then vertically - Tighten the fasteners of the bracket/window lifter (M6) 12 + 5 Nm - Fit the nut on the spacer at the top but do not tighten it 6. Adjust the mounting at the front - Lift the window; it must lie parallel against the rear guide along its entire length - Undo the fasteners for fore/aft adjustment - Align the bracket with spacer to the bore in the window mounting, first in the longitudinal direction and then vertically - Tighten the fasteners of the bracket/window lifter (M6) 12 + 5 Nm. Fit the nut on the spacer at the top and tighten it (M6) 12 + 5 Nm 7. Now tighten the nut on the rear spacer at the top (M6) 12 + 5 Nm 8. Check the movement of the window - On the outside of the window, mark the position of the window relative to the rear window guide with tape - Open and close the window several times - The movement of the window should run parallel and uniformly along the guide, free of any tilting motion - Repeat the adjustment procedure if necessary 9. To complete the adjustment, check the window for ease of movement. To do this, measure the power consumption of the window lifter motor. The maximum current draw is approximately 9 Amps while the window is being raised.

and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.

Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.

Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data

that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?

C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.

Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data

Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

generates a cracking noise when exiting the upper /lower adjustment position (e.g. for Easy Entry function). Cause: Height adjustment runs into upper / lower limit stop and jams there or generates a breakaway cracking noise when exiting the jammed limit stop. Remedy: 1. Move fore/aft adjustment to the end position. 2. Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel. At the same time, push adjusting switch (downwards). 3. Commission driver's seat control unit. While doing so, - the control unit software is updated, if necessary - the limit stops are cleared and normalized again - and any renewed jamming is prevented 4. Once commissioning has been completed the vehicle can be handed over to the customer.

Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.

The control unit 'Roll control' has a malfunction. 2. In vehicles up to VIN 166 ### #A 097760 with code 803 or vehicles as of VIN 166 ### #A 097761, the following fault code is logged in the quick test: P1C9564. The rotation direction valve of the torsion bar ''Front axle'' has a malfunction.

clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.

unit: P100000: The oil pressure at the front axle is too low. (Veh. up to approx. 7/2012) P100200: The oil pressure at the rear axle is too low. (Veh. up to approx. 7/2012) P1C9C00: The oil pressure at the front axle is too low. (Current veh.) P1C9E00: The oil pressure at the rear axle is too low. (Current veh.) In addition, the following complaints may occur depending on symptoms: Gushing/flow noises from the front or rear axle area when cornering. Oil leaking via the ACS reservoir.

1. Left cylinder head: Oil passage plug hole on left beside mechanical vacuum pump. 2. Right cylinder head: Oil passage plug hole below high-pressure pump housing.

Fault code 20B91B, 20B913 (The output for the heating element of the AdBlue pressure line has an electrical fault or an open circuit) is stored in the SCR control unit.

Fault code 20BE1B and/or 20BD1B (The heating element of the AdBlue tank has a malfunction) is logged in the Blue-Tec control unit.

Fault code 20BE1B and/or 20BD1B (The heating element of the AdBlue tank has a malfunction) is logged in the Blue-Tec control unit.

OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: Hitting the curb/posts with the front wheels. Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). Cracks (1) High pressure cleaner (2) Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

236.17 due to a global supply constraint. 236.17 ATF 1L and 5L (PNs: A002989060312 and A002989060313) bottles are out of stock or in limited supply at Zep. This LI has been created with the following intention: - Provide dealers with additional workshop-focused guidance regarding the current ATF 236.17 supply constraint and the planned introduction of ATF 236.18. - Supplement existing communications and address common workshop questions related to maintenance, repairs, and fluid applicability. - Provide technical clarification and practical workshop guidance during the temporary supply constraint period. Dealers should continue to reference the latest News Channel Updates (NCUs) for the most current information regarding availability, ordering processes, supply status, and other related updates. Cause Damage to the Shell production facility has resulted in 236.17 oil supply being reduced to 50% of normal output until the end of 2026. Remedy Please first check Latest NCU updates for latest detailed information. Please continue placing orders through Paragon as normal. Supply is expected to remain reduced and allocation measures are currently in place. We ask for your patience through this restricted supply period. Most orders will be filled in the order in which they were received, as supply is replenished. Those dealers with zero inventory, and pending orders, will receive priority. We expect supply to be stabilized in September 2026. Approved Fluids: Only use transmission fluid from the approved list found on the Mercedes-Benz Operating Fluids website. Non-approved fluid will result in mechanical damage to the transmission and must be avoided. https://operatingfluids.mercedes-benz.com/sheet/236.17 Approved fluids can be claimed as follows if there is no Mercedes-Benz part number: Part # ATFSUB1L - TRANSMISSION FLUID 1 LITER ATFSUB5L - TRANSMISSION FLUID 5 LITER Dealerships with Zero Inventory AND Grounded Vehicles: If a vehicle is currently grounded for repair at your dealer due to no 236.17 inventory, we may be able to expedite your order. Please open a StarSupport ticket including the following information: (Parts Related Inquiry>National Accounts>Zep) LI document number Short explanation of repair needed for grounded vehicle Current days down of RO Maintenance and Service Interval Guidance Published maintenance intervals remain unchanged. Vehicles should continue to be maintained in accordance with the applicable maintenance schedule. This LI does not revise or extend any published maintenance interval requirements. If all required parts and materials are not available prior to scheduling or beginning a transmission service, dealers should consider postponing routine preventative transmission maintenance until the necessary parts become available. For vehicles that have not yet reached the applicable maintenance interval and do not exhibit transmission-related concerns, there is no need to recommend preventative transmission services prior to the scheduled maintenance interval. When evaluating whether routine transmission maintenance can be deferred until parts become available, dealers should consider: Overall vehicle condition Vehicle usage and operating conditions Presence of transmission-related symptoms or customer complaints Customer expectations and vehicle operating requirements Availability of required parts and materials Introduction of New Fluid Specification 236.18 Mercedes-Benz is currently preparing the introduction of ATF 236.18 as an additional approved transmission fluid solution for applicable NAG3 transmissions. At the time of publication of this LI, ATF 236.18 is not yet available for dealer ordering or workshop use in the U.S. market. See attachment for further details.

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CPR = Car Package Release (For MB.OS) CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465, 906 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

The clunk is heard once when changing from forward to reverse (and vice versa). Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.

and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid

transmission may perform an "Automatic P function" at speeds below 6 km/h.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

control unit (N112/9) is not supported for gray-market vehicles. Cause Before deactivating the HERMES control unit (N112/9), it must be clarified by the legal department of the respective MPC whether and under what conditions deactivation may be carried out. If deactivation is not permissible under applicable law, the HERMES control unit (N112/9) must not be deactivated. Remedy Please inform the customer that, following deactivation, the vehicle will no longer be able to place an automatic emergency call, nor will the customer be able to place a manual emergency call. After deactivation, the Mercedes-Benz Digital Extras will also no longer be available. Please have the attached sample form checked by your market's legal department, adapted to local requirements if necessary, and approved. Furthermore, after informing the customer about the effects of deactivation, please have the workshop complete and sign the approved form together with the customer, and send it to the MPC via a TIPS case for audit-compliant documentation. Furthermore, the workshop must affix a sticker to the emergency call button cover on the overhead control panel and to the emergency call button itself. After affixing, pictures of the overhead control panel need to be attached to the TIPS case for audit-proof documentation. After deactivation, the HERMES control unit (N112/9) is in the "Out of Service" operating status, and the display "SOS NOT READY" appears in the Audio/COMAND system. This display message tells the customer that the emergency call function is not available. In detail, the following steps must be carried out 1. The workshop must inform the customer about the effects of deactivation (see above) 2. Legal review by the MPC Legal department to determine whether deactivation is permissible for the vehicle and provision of a market-specific customer form based on the examples (see "Example - Deactivation communication module HERMES customer declaration English V3.0.pdf") 3. Completion of the market-specific customer form by the workshop and obtaining the customers signature 4. Creation of a XSS ticket by the workshop for the MPC with the signed customer form attached 5. Written confirmation of legally reviewed and approved deactivation by the MPC in the TIPS case (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, point 1) 6. Creation of an XSS ticket for documentation of the SA code "09o" (zero nine oh) in the Vehicle Documentation System (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, steps 27) 7. Ordering of stickers (part number A9078172900), quantity: 2 8. Affixing of the sticker (part number A9078172900) to the cover of the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 9. Affixing of the sticker (part number A9078172900) to the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 10. Taking photos of the applied stickers and attaching them to the TIPS case 11. After the XSS ticket has been successfully processed, the communication module must be deactivated using XENTRY: Connect XENTRY Diagnosis Access the HERMES control unit (N112/9) "Adaptation" tab, menu item "Teach-in processes" -> "Deactivation" Follow the instructions

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: vehicle technical issue? customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: Amperage setting of charger and time battery was on charger XENTRY Battery Tester results Voltage of battery taken with multimeter: Do not connect charger while taking measurements N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) Workshop analysis of conspicuous data Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

message "SOS - Service not activated" is displayed in the instrument cluster. Cause The message "SOS - Service not activated" tells the customer that "over-the-air" registration of the vehicle with the Mercedes Intelligent Cloud is not possible. On a gray import vehicle, this is due to the fact that the SIM card installed in the HERMES communications module cannot dial into the mobile phone network in the importing country. Remedy The only way of avoiding the message in the instrument cluster is to deactivate the HERMES module using the 09o deactivation process after obtaining the customer's consent. After deactivation, the HERMES control unit (N112/9) has the operating status "Inoperative". The message "SOS not ready" appears in the audio/COMAND display (A40/8) and may also appear in the instrument cluster. This display message tells the customer that the emergency call function is not available. In addition, the workshop must attach a label (2 x part number A9078172900 required) to the cover of the emergency call button in the overhead control panel and to the emergency call button itself. Replacing the hardware of the HERMES communication module is not effective.

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware ISU = Initial Start Up LVDS = Low Voltage Differential Signal NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465, 906 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" No vehicles currently launched.

Please note that if the complaint "Fuel filler flap not opening" occurs, it is important to check the fuel filler flap before replacing the central locking actuator. For gasoline hybrid vehicles where the fuel filler flap fails to open or does so but slowly, observe the document "Fuel filler flap fails to open or does so but slowly on plug-in HYBRID gasoline vehicles"! Cause Central locking actuator may have an electrical fault and may not open. Remedy 1. Car locked: To rule out incorrect operation, operate the fuel filler flap in the area shown in Fig. 1 and listen out for the clicking noise of the microswitch in the central locking actuator. If no clicking can be heard, continue with point 4. 2. Car unlocked: Press area on flap to start the microswitch clicking. Flap opens - show the customer the area to press. 3. Car unlocked: Flap cannot be opened regardless of which area you press. Open the flap by operating the emergency release for the CL actuator (through trunk, fender gap cover, etc, depending on specific vehicle) 4. Central locking actuator pressed directly, no clicking of microswitch, no electrical release of central locking actuator => Clicking of microswitch, electrical release of central locking actuator => Tank filler recess/charging recess not OK; report results via a TIPS case to B/C/E Inbox. 5. Replace central locking actuator; check function of new part before installing it: Do not dispose of damaged part. New central locking actuator does not release: More detailed examination of connector coupling, wiring harness, electrics required.

CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.

Because of this the previous telematics DVDs A 204 827 03 65 and A 204 827 10 65 must continue to be used for control unit programming. If required, these are still available for ordering. With XENTRY DVD 03/2014 a new telematics DVD with part number A 166 827 21 00 is being shipped. This telematics DVD replaces the previous telematics DVDs.

in the stowage compartment of the center console.

As described in AR68.30-P-4300GQ, 2-component adhesive A 005 989 09 71 is to be used for gluing on the headliner magnets. Any missing magnets can be reordered as of 03/2014.

or "Stage 2" in the instrument cluster.

NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not preauthorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify.

Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles in the below FIN range. FIN range up to: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Axle Half Shaft noise when changing direction - Front) LI33.30-P-056665 (Axle Half Shaft noise when changing direction - Rear) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range above): 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.

Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.

Sometimes a single jolt can also be felt at the steering wheel.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Cause Possible tolerance complaint regarding the door handle Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3).

Cause Alignment of door handle bearing bracket is not correct. Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace the door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3).

Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Suitable interior protection ensures that the interior monitoring function continues to operate correctly.

on rough roads.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10P067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.

Cause Many possible root causes Remedy *Note - This Li does not apply if there are other Li's that apply to your concern OR you have a fault and/or guided test that leads to a root cause. AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements (Template attached to be used for submission of Warranty claim and/or TIPS case) Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements Cooling Capacity Test (If System Has a Charge) Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs - Warranty Submission Requirements on the Repair Order Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found

message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, June 11, 2026. After June 11th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

The deadline for all dealer returns is no later than Thursday, June 4, 2026. After June 4th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

and play them with Windows Media Player. Cause Driving with summer tires in combination with low outside temperatures. At low outside temperatures or in wet conditions, a noise may be produced at the outer wheel on the front axle while maneuvering with sharp steering angles. Note: AMG vehicles with 4MATIC of model series 217 (without code 494) and model series 222 have a modified axle geometry compared with series production vehicles to provide more sporty handling. The problem cannot be remedied by changing the axle settings.

cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.

instructions on how the HVAC Service Warranty repair must be carried out. To enhance the satisfaction of our customers, avoid further costs of litigation, and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew odors originating from the HVAC system. Although the settlement has received court approval, warranty coverage will not take effect until December 7, 2020, when the appeal period for class members will have expired. If the settlement takes effect, warranty coverage will include cleaning of the evaporator and replacement of the HVAC filters.

Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters

periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!

The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.

The clunk is heard once when changing from forward to reverse (and vice versa).