2025 Mercedes-Benz AMG E 53 4Matic+ Wagon TSBs

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by doubleclicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again and anywhere there are movement or friction points that the noise seems to be emanating from. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

CarPlay over Wi-Fi Audio cuts out Device not recognized No operation possible Cause There are multiple possible causes for an iPhone disconnecting from a vehicles head unit while using Apple CarPlay. These include hardware, software, and environmental factors: Environmental Interference: External Sources: Passing under toll bridges, driving near airports, or areas with heavy electronic interference can cause connection drops. Cellular Networks: Interference from nearby cell towers operating on similar frequencies (usually 2.4GHz or 5GHz) can disrupt the signal. Storage Location: Keeping your phone in a handbag or surrounded by other objects inside the vehicle can create physical or electronic interference. Device and Software Topics: Head Unit Software/Hardware: Hardware causes or outdated firmware in the vehicles head unit can prevent a stable connection. iPhone Software/Hardware: Similar causes in the iPhone, including outdated iOS versions or hardware causes, may affect performance. Reset or Reboot: Automatic rebooting or resetting of either the head unit or the iPhone will temporarily disrupt CarPlay. Connection and Settings: Wired Connections Cables: A compromised or poor-quality iPhone-USB cable can cause intermittent or total loss of connection. USB Ports: Dust, debris, or physical deformation in the USB port of either the head unit or the iPhone can also lead to disconnects. Wireless Connections: Intermittent Bluetooth/Wi-Fi: Unstable wireless communication (Bluetooth/Wi-Fi) can frequently break the Car- Play connection. Power Management: Battery Saver Mode: Enabling low power mode may restrict background processes, affecting CarPlay. Vehicles Electrical System: Unstable power delivery from the cars battery or electrical interruptions can cause the head unit to malfunction. Phone & App Configuration: Phone Settings: Settings (especially Bluetooth or Wi-Fi) on your iPhone can interfere with the CarPlay link. Third-Party Apps/Profiles: Installed apps or configuration profiles may conflict with CarPlays operation. Native apps are apple maps, apple music, audio books, apple news, podcasts, messages and phone. All other apps are considered third party apps. App Conflicts: Running conflicting apps that require similar system resources as CarPlay can cause instability. Mobile Data Plan: Streaming from online sources without sufficient mobile data can result in lost connectivity. Other Factors: Heat & Overheating: If either the phone or the head unit overheats, they may disable certain functions to prevent damage, leading to disconnection. User Actions: Accidentally disconnecting the device in settings, or physically moving or bumping the phone or cable, may disrupt the connection. Remedy Guided Diagnostic Path for Apple CarPlay Connection Issues Please follow the steps below to systematically diagnose and resolve CarPlay concerns: Update Devices: Ensure the iPhone is updated to the latest available iOS version. Ensure the vehicles head unit is updated to the latest software version available. Isolate the Issue: Check whether the symptom persists with another iPhone running the latest iOS version. Test both wireless and wired CarPlay connections: Does the issue only occur with wireless CarPlay? Does the wired connection to the phone function correctly? Further Troubleshooting Steps: Reboot the iPhone. Reboot the head unit via the settings menu (user data reset). Remove saved CarPlay connections Delete the head unit information from the iPhone (see attached video for guidance). Delete the iPhone from the head units list of paired devices. Remove the head unit entry from CarPlay settings on the iPhone. Re-initiate pairing between the head unit and the iPhone to establish a new connection certificate. See attachment for complete text.

electrical system The following fault codes related to stuck contactor can be found in the High Voltage Control units : PTCU - N127 (Powertrain control unit) P154900 - There is a warning due to overcurrent in the charging system of the high-voltage electric circuit. P154A00 - There is a warning due to a detected crash event at standstill. P154B00 - There is a warning due to a stuck contactor. DCB223 - N116/5 (Direct current charge connection unit) P0E8929 - The input current of the on-board DC charging connection unit is too high. There is an invalid signal. P2BC500 - The contact ''Positive terminal'' of the contactor in the on-board DC current charge-connection unit is jammed closed P2BCC00 - The contact ''Negative terminal'' of the contactor in the on-board DC current charge-connection unit is jammed closed. Cause Current ripple due to EVSE (Electric Vehicle Supply Equipment) Overcurrent or Overvoltage due to EVSE (Electric Vehicle Supply Equipment) DCB contactors did not open immediately due to welding time at the end of DC charging Remedy Check for a new software availability for DCCU (N116/5 - Direct Current Charge connection Unit). If a new software is available, update the software first. Reset contactor fault through special procedure without password. ( N116/5 >> Special Procedure >> Resetting of contactor fault.) Important Note : Do not replace component DCB (N116/5) If fault codes are not erasable, please raise a TIPS case and send it to HQ.

software for the Mobile Access Unit (MAU) control unit may not correspond to the current series production configuration. This OTA software update for the Digital Vehicle Key (DVK) function within the MAU will improve battery management by disconnecting the vehicle network when it is not required. In addition, the software update contains general improvements for system stability and DVK device compatibility. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

Cause: Unfavorable manufacturing tolerances in the production process of the drive shaft. Remedy: If the above-mentioned customer complaint is present, a test drive and thorough NVH diagnosis must be performed in order to verify the root cause of the noise. If the axle shafts have been identified as the source of the noise, determine the vehicle production date and perform the following steps: (Date format > MM/DD/YYYY) Vehicles up to production date 12/09/2024: Replace both rear axles with A 214 350 44 06 Vehicles as of production date 12/10/2024: Do not replace any parts (wheel bearing, axle shaft) as it will not resolve the concern. A 214 350 44 06 must not be replaced. If rear axle shafts A214 350 44 06 are already installed and the noise is still present, please submit a TIPS case to the Powertrain inbox with the following information: - Initial Quick Test w/ Freeze Frame Data - Video or Sound file of the noise concern with details of where the recording was taken (ex. inside/outside vehicle, where sensors were placed) - Clear photos of part labels on both rear axle shafts - If possible, breakaway torque when loosening the axle bolt - Clear photos of the mating surfaces of rear axle shafts and wheel bearings

reduced range of functions" in relation to "FC151E29- The level sensor at front left has a malfunction. There is an invalid signal" in the HLI control unit. Cause HLI control units processing of level sensor data. Remedy Update the software for the HLI control units - starting with the left controller. After the updates, perform SCN coding of the EZS. Please ensure that the SW with the A item number A2239027738 (or newer) is used. Parts replacements will not resolve complaint. Do not replace parts. If concern is not resolved by software, please open a TIPS case and send to the Body/Chassis/Entertainment inbox. Concern does not impact drivability of the vehicle or the function of the headlights.

reduced range of functions" in relation to "FC151E29- The level sensor at front left has a malfunction. There is an invalid signal" in the HLI control unit. Cause HLI control units processing of level sensor data. Remedy Update the software for the HLI control units - starting with the left (driver side) controller. After the updates, perform SCN coding of the EZS. Parts replacements will not resolve complaint. Do not replace parts. If concern is not resolved by software, please open a TIPS case and send to the Body/Chassis/Entertainment inbox. Concern does not impact drivability of the vehicle or the function of the headlights.

coding for the electronic ignition lock control unit does not correspond to the latest series production configuration. The electronic ignition lock control unit will be updated to change the logic for locking and unlocking the vehicle via the door handles. To unlock the vehicle, the large outer contact surface of the door handle must be touched. To lock the vehicle, the small, recessed contact surface of the door handle must be touched. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: vehicle technical issue? customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge, create a TIPS case. -Must include with the case: Amperage setting of charger and time battery was on charger XENTRY Battery Tester results Voltage of battery taken with multimeter: Do not connect charger while taking measurements N10/6 FSAM and N73/3 EZS CUL Workshop analysis of conspicuous data Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Test: Please perform the new SCN coding for HOSWD control unit (N179/1) (available since May 2025). Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> Please create TIPS case! If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no fault is visible: Please open a TIPS case! In the event of a customer complaint and further fault code in HOSWD: B1E7713: Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). B1F1F04: Check hand detection system control unit; if necessary swap with donor vehicle (ensure that the HW part numbers are identical).

Cause Enhanced technical support process for CIVIC modules and associated displays Remedy Note: Do not replace any components. For all symptoms concerning CIVIC and displays create a TIPS case after performing initial diagnosis. Attach the following documents to this case: Quick test Control unit logs for CIVIC and all displays If possible, obtain customer consent for CIVIC logging that needs to be reviewed by GSP (see attachment). In some instances the CIVIC logs may not be required. After receiving the case if it is determined that CIVIC logging is required, a password will be generated for activation of the CIVIC logging (where the customer has approved this). This password and Xentry instruction on how to create a log will be communicated in the TIPS case. The password is case sensitive and only valid for 24 hours. Note: If unable to obtain the customer approval for CIVIC logging, simply state so in the TIPS case notes.

Cause Temperature sensor in overhead control panel (OCP) delivering incorrect values: The temperature sensor in the overhead control panel is malfunctioning. Fault code B110709 or fault code B11F697 are present in the overhead control panel with the status (active) or (active stored). or The temperature sensor in the overhead control panel measures an incorrect temperature (the temperature value can be checked against the actual value in the overhead control panel) If the above-mentioned fault code is not present, the cause could be malfunction on the air conditioning system. Remedy If one of the above-mentioned fault codes should occur, a TIPS case must be created here. If the above fault codes or actual value differences are present in the OCP - please send the case to the Body/Chassis/ Entertainment inbox. Otherwise, the case must be sent to the HV/LV inbox for support in A/C diagnosis. *** It is not necessary to replace the overhead control panel ***

reduced range of functions" in relation to "FC151E29- The level sensor at front left has a malfunction. There is an invalid signal" in the control unit HLI/LED headlamp range adjustment front left. Cause Electronic interference occurring at the sensor level of the front axle. Remedy Update of the HLI/LED headlamp range adjustment control units.

mobile device connection control unit software does not correspond to current production specifications. The mobile device connection control unit will receive an over-the-air (OTA) software update which improves general system stability and device compatibility for the Digital Vehicle Key functionality. The update is downloaded in the background and the customer will be prompted to accept or decline installation during the following ignition cycle. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

The software for the communication module does not correspond to the latest series production configuration. The communication module will receive an OTA update. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

Cause The problem was caused by a software error in the control unit N10/8 (Rear SAM). Remedy Software update to the control unit N10/8 (Rear SAM - Signal acquisition and actuation module rear control unit).

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Enter AO Code O19 into VeDoc (O for Oscar, not "zero") 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 double-click on the locking button As of modification year 22/1, by pressing and holding the locking button + double-clicking on the release tab On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

The vehicle starts or charges normally and without any problems. Current and saved fault code in DCCU and powertrain control unit (PTCU): P2E9873 The position sensor of the external socket flap of the vehicle socket (direct current) indicates an electrical fault. The actuator does not open. Cause Software in the control unit "N116/5 - DC charge-connection unit (DCCU)". Remedy Update software for N116/5 (DC charging control unit box) and perform SCN coding of N116/5. Once the SCN coding has been updated, the engine diagnosis indicator lamp (MIL) is no longer actuated with this fault code.

P13C273 P13C278 P140473 Cause Various Remedy Model year 2024 254 and 167 with engine M254 -Update software of N127 PTCU. New software: 254- A2549022611 167- A2549022811 -Clear fault codes and check operation of the exhaust flap. Models with M256, or models with M254 after SW update -Check exhaust flap for free movement via actuation. -Remove flap actuator and check movement of flap in exhaust pipe. Replace exhaust pipe section if flap is binding. -Replace flap actuator if above checks are ok. If fault code returns after performing the above steps, open a TIPS case with the powertrain team. Note: Codes P13C273 and P13C278- Right side flap Code P140473- Left side flap

Note: When ECO start-stop is active, the engine is shut off before the 2-1 shift and the complaint will not occur. Cause Software application when engine is running. Remedy Short-term remedy: Perform IPR and follow the instruction to perform standstill adaptations. Long-term Solution: Aftersales software is currently in development. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

with Easy Entry function), noise (breakaway noise) when leaving the limit stops of the height adjustment. Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Driver seat control unit software 2. Steering column height adjustment transmission Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Perform software update of driver's seat control unit 2. Replace repair kit for steering column height adjustment Procedure 1: Perform software update of driver seat control unit. ALL models except 205/253/293/222/217/231/463/213/238/257/290 up to special equipment code 801. Move out the fore/aft adjustment to the end position. Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward After releasing the jam, perform a software update of the driver's seat control unit If procedure 1 is not effective, there is no new software available for the driver seat control unit, or the chassis is not listed above (167, 223, 294, 206, 294, 295, 296, 297,232,214,254) then use procedure 2. Procedure 2: Replace repair kit for steering column height adjustment. Move out the fore/aft adjustment to the end position. Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward Remove footwell trim on driver's side. Determine type version of height adjustment in XENTRY Parts Information and order appropriate replacement part (refer to attachment). 1. Version A: A 231 460 77 00 2. Version B: A 205 460 38 03 Remove steering column. Remove height adjustment (adjustment repair kit). Install repair kit (adjustment repair kit) (observe tightening torque for screws in attachment). Install steering column. If possible, flash driver seat control unit to latest software release or code SCN again. Commission driver seat control unit (normalization of limit stops is deleted and learning process repeated).

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". 5. Apply heat-resistant lubricating paste to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 6. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. e) Finally drive approx. 3 miles to allow the system to cool. f) Reassess noise.

- Current and saved fault code in DCCU and powertrain control unit (PTCU): P2E9873 The position sensor of the external socket flap of the vehicle socket (direct current) indicates an electrical fault. The actuator does not open. - The vehicle starts or charges normally and without any problems. Cause Software in the control unit "N116/5 - DC charge-connection unit (DCCU)". Remedy For model series 167 (Only for USA): Remedy is available: Update software for N116/5 (DC charging control unit box) and perform SCN coding of N116/5. Once the SCN coding has been updated, the engine diagnosis indicator lamp (MIL) is no longer actuated with this fault code. For other model series: Work on the SW remedy for N116/5 (DC charging control unit box) is in progress. Once the software is available, update the software for N116/5 and perform SCN coding of N116/5. If this problem occurs, the vehicle start or charging functions are normally not affected; therefore do not replace any parts. Replacing parts does not solve this problem.

unit N127: P052497 The oil pressure is too low. The system function is restricted. P052400 The oil pressure is too low Cause Various Remedy If low oil level warning present diagnose cause of this first. -Check engine oil level and correct if necessary. Refer to vehicle specific instructions AP18.00-P-1848U -Check for external engine oil leaks -Measure engine oil pressure via graphical representation in MRG actual values. In one measurement capture the pressure at idle, 1000, 2000, and 3000 rpm. Hold each range for approx. 5 seconds. -Save results as CSV file -Create TIPS case and submit to the powertrain team, including Oil pressure test results CSV file Initial quick test Any additional test results or observations Any previous diagnosis or repairs performed

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10P067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations Teach-in processes ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.

Please also see LI54.65-P-080132 for additional listed red ring causes. Cause EMF interference. Remedy Camera functionality is not affected. Cameras and displays operate normally. For vehicles with a front facing actuating camera and flap (223 and 297): 223, 297 > Install clip on ferrite magnet on M35/1, pin 3. For vehicles with rear facing camera (223, 213 Facelift, 238, 257, 290, 297): 297 > Install 2 x ferrite magnets on M35/2, pin 3 and 4. 213 Facelift, 223, 238, 257, 290 > Install on M35/2, pin 4

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q4 2025 to early Q1 2026 to rectify concern.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Head unit software variant. Remedy For all chassis use Xentry to update head unit (A26/17). Target boot software number should be either: 247 904 6600 (E905.4) OR 247 904 7500 (E906.1) If vehicle fits all criteria and either target software is not available via Xentry, please open an XSS ticket. Damage code 5424x-01 may be used with a repair start date after June 2nd, 2025.

MBUX multimedia system software does not correspond with the latest series production configuration. The MBUX multimedia system software will receive an update to introduce new functions and improve the customer experience. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Under analysis. Remedy For chassis 118, 167, 177, 213, 238, 243, 247, 253, and 293 use Xentry to update headunit (A26/17). Target software number is 247 904 6600 (E905.4).

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: Fluid intrusion Broken bushings or physical damage See attachments. Remedy If a component needs replacement but shows no visible external damage, submit a detailed TIPS case only when technical support is required. Include details of all connected external devices (such as charging cables, USB drives, and hard drives). If diagnostic results directly indicate component replacement, a TIPS case is not necessary.

Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: Fluid intrusion Broken bushings or physical damage See attachments. Remedy If a component needs replacement without visible external damage, submit a detailed TIPS case. Include information on all connected external devices (e.g., charging cables, USB drives, hard drives).

if Digital Extra: Active Distance Assist DISTRONIC (207) has already been activated/purchased via the application. Cause On some vehicles with Digital Extra: Active Distance Assist DISTRONIC (code 207), it may be that the function cannot be enabled via the application or is no longer available in the "vehicle back end". Remedy Please open a case with the Customer Care Center ("CCC") to reactivate function on the "vehicle back end".

Cause Unfavorable manufacturing tolerances in the production process of the drive shaft. Remedy If the above-mentioned customer complaint is present, perform the following operation steps: 1. A test drive must be performed. 2. For a precise noise analysis (localization of the noise), make use of the noise case. If the side shafts of the rear axle have been unequivocally identified as the cause (source of the noise), both side shafts at the rear axle must be replaced. The following part numbers must be installed: A 214 350 44 06 Side shaft

Cause Unfavorable manufacturing tolerances in the production process of the drive shaft. Remedy If the above-mentioned customer complaint is present, perform the following operation steps: 1. A test drive must be performed. 2. For a precise noise analysis (localization of the noise), make use of the noise case. If the side shafts of the rear axle have been unequivocally identified as the cause (source of the noise), both side shafts at the rear axle must be replaced. The following part numbers must be installed: A 214 350 44 06 Side shaft

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

236.17 due to a global supply constraint. 236.17 ATF 1L and 5L (PNs: A002989060312 and A002989060313) bottles are out of stock or in limited supply at Zep. This LI has been created with the following intention: - Provide dealers with additional workshop-focused guidance regarding the current ATF 236.17 supply constraint and the planned introduction of ATF 236.18. - Supplement existing communications and address common workshop questions related to maintenance, repairs, and fluid applicability. - Provide technical clarification and practical workshop guidance during the temporary supply constraint period. Dealers should continue to reference the latest News Channel Updates (NCUs) for the most current information regarding availability, ordering processes, supply status, and other related updates. Cause Damage to the Shell production facility has resulted in 236.17 oil supply being reduced to 50% of normal output until the end of 2026. Remedy Please first check Latest NCU updates for latest detailed information. Please continue placing orders through Paragon as normal. Supply is expected to remain reduced and allocation measures are currently in place. We ask for your patience through this restricted supply period. Most orders will be filled in the order in which they were received, as supply is replenished. Those dealers with zero inventory, and pending orders, will receive priority. We expect supply to be stabilized in September 2026. Approved Fluids: Only use transmission fluid from the approved list found on the Mercedes-Benz Operating Fluids website. Non-approved fluid will result in mechanical damage to the transmission and must be avoided. https://operatingfluids.mercedes-benz.com/sheet/236.17 Approved fluids can be claimed as follows if there is no Mercedes-Benz part number: Part # ATFSUB1L - TRANSMISSION FLUID 1 LITER ATFSUB5L - TRANSMISSION FLUID 5 LITER Dealerships with Zero Inventory AND Grounded Vehicles: If a vehicle is currently grounded for repair at your dealer due to no 236.17 inventory, we may be able to expedite your order. Please open a StarSupport ticket including the following information: (Parts Related Inquiry>National Accounts>Zep) LI document number Short explanation of repair needed for grounded vehicle Current days down of RO Maintenance and Service Interval Guidance Published maintenance intervals remain unchanged. Vehicles should continue to be maintained in accordance with the applicable maintenance schedule. This LI does not revise or extend any published maintenance interval requirements. If all required parts and materials are not available prior to scheduling or beginning a transmission service, dealers should consider postponing routine preventative transmission maintenance until the necessary parts become available. For vehicles that have not yet reached the applicable maintenance interval and do not exhibit transmission-related concerns, there is no need to recommend preventative transmission services prior to the scheduled maintenance interval. When evaluating whether routine transmission maintenance can be deferred until parts become available, dealers should consider: Overall vehicle condition Vehicle usage and operating conditions Presence of transmission-related symptoms or customer complaints Customer expectations and vehicle operating requirements Availability of required parts and materials Introduction of New Fluid Specification 236.18 Mercedes-Benz is currently preparing the introduction of ATF 236.18 as an additional approved transmission fluid solution for applicable NAG3 transmissions. At the time of publication of this LI, ATF 236.18 is not yet available for dealer ordering or workshop use in the U.S. market. See attachment for further details.

It may be mistaken for a hard brake engagement Cause Poor learning of brake B06 adaptation values over time. Remedy Short-term remedy: 1. Perform IPR and follow the instructions. 2. Perform resetting of deceleration values (VGS > Special Procedures > Special procedure > Resetting learned values Deceleration mode) 3. Perform standard adaptation 4. Reevaluate the concern and release vehicle if no longer present Note: ALL steps (resetting learned values and standard adaptation) must be completed to fully resolve the complaint. Long-term measure: Aftersales software is currently in development.

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

Cause The cause is currently being investigated. Remedy A remedy is currently not available. A software update in the seat control unit does not solve the problem. The document will be updated once the reason has been analyzed and a remedy is available.

with one of the following scenarios: Flashing without a speed limit ("- -"). Flashing when current vehicle speed is under speed limit. Flashing between US speed limit symbol and European speed limit symbol. Cause Under Investigation Remedy Under investigation. One option is to turn off Traffic Sign Assist until the investigation is completed. Once completed this LI will be updated. No TIPS case is necessary. Do not replace parts.

If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document. Conditions Instrument Cluster Message: "Park Assist Inoperative" and Hardware part numbers: A0009019716 or A0009016022 B223263 with Bosch-ID C259; A+S (Active and Stored) and B223255 with Bosch-ID 1B5D; A+S (Active and Stored) Notes: Other DTC's are permitted but the above three conditions must be met. If they are not met, this LI is not applicable. See attachment "LI Criteria" for an example. Attachment portrays a quick test with non-matching criteria and therefore does not require a TIPS case. Cause Under analysis. Remedy Please do not make any attempts to repair the park control unit. Do not flash or SCN code. Open a TIPS case.

NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not preauthorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

TIREFIT sealant bottle may not meet specifications. The possibility exists that the sealant bottle may leak or may have otherwise been removed from the vehicle. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk.

Cause One or several locking clips on the trim strip are broken. Remedy Only applies to vehicles up to FIN end number: 214 xxx xx 159 188 Only applies to trim strips with the SA code "772+PUF" -> A 214 885 7802 -> A 214 885 7702 If the conditions mentioned apply, the defective trim strip must be replaced.

to: Summer heat Direct sunlight Lack of air conditioning or ventilation Camera enters self-protection mode to prevent overheating. Remedy Do NOT replace any parts. The driver camera (NTG7: MDC295; CIVIC.i2: CIVIC206) is operating as designed. Allow the interior to cool down. If the message remains after cooling: Run XENTRY Diagnosis Check latest software for Actuation of Driver Camera (A26/17) No TIPS case required.

sound does not meet the customer's expectations. Changing the sound settings, for example for the bass, does not provide the desired effect. Cause Sound parameter software in the A26/17 - MBUX multimedia system + Instrument cluster (Head unit) control unit Remedy For vehicles with standard sound and Midline sound system (code 853), new sound parameters are available. V/X 254: A 254 903 94 03 C 254: A 254 903 97 03 V/W 206: A 206 903 20 04 S 206: A 206 903 21 04 A/C 236: A 236 903 86 01 V/W 214: A 214 903 19 03 S 214: A 214 903 20 03 To update the sound parameters, please perform an update to the software for the A26/17 - MBUX multimedia system + Instrument cluster (Head unit) control unit.

instrument cluster upon vehicle start-up, prior to driving. No fault codes stored in the rear axle steering control unit N68/4. Cause Asynchronous start-up of control units in the vehicle. Remedy The message clears once the head unit receives the rear axle steering signal. Perform a software update to A26/17 control unit - MBUX multimedia system + instrument cluster (head unit) CIVIC206; the software version must be at least 333.8. NOTE: To verify the head unit is on the correct software version: Navigate to A26/17 (Head Unit) Control Unit Log. Locate "Control Unit Specific Data" near the bottom. Verify "E-Stand" number is at least 333.8.

Based on technician feedback, the OTA (code: 25P5496529) does not start even after an extended period of time and several driving cycles. In addition, the "Continue" button is grayed out. Cause The exact cause for the OTA not to start is currently under analysis. Remedy Please check whether the vehicle is affected by the field measure "Update software of Supplemental Restraint System (SRS) control unit" (code: 25P5496529) and if yes, perform this update using a XENTRY with all latest Add-Ons and bill under accounting number 5496529. If the vehicle is not affected by this field measure, in the event of a complaint update control unit ORC223 (N2/5 -Supplemental Restraint System SRS) using XENTRY and use damage code 8251M01. As of XENTRY Release Version 06/25, control unit ORC223 can also be updated in this context without a password. Provided control unit ORC223 is error-free after the update, the vehicle can be handed back. ***IMPORTANT*** -In isolated cases, the OTA update may continue to be displayed for up to 3-4 weeks even after flashing with XENTRY. Note: This LI applies only to the OTA update for occupant protection!

Cause Noise in the backrest adjustment mechanism Remedy The adjustment mechanism is treated with dry lubricant spray A000 989 35 60 to rectify the noise. To do this, proceed as follows: Move the seat to the front position and put the backrest into a lying position. Due to the risk of soiling on the left and right under the adjustment mechanism, cover and protect the area. Spray into the gap of the left and right adjustment mechanism with dry lubricant spray from above. If the noise persists, then repeat the process. Enough dry lubricant spray must be used Then wait 15 minutes and leave the seat in this position! Only then adjust the seat into the sitting position. Note: Both front seats must always be treated!