2021 Mercedes-Benz A 220 TSBs

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by doubleclicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

CarPlay over Wi-Fi Audio cuts out Device not recognized No operation possible Cause There are multiple possible causes for an iPhone disconnecting from a vehicles head unit while using Apple CarPlay. These include hardware, software, and environmental factors: Environmental Interference External Sources: Passing under toll bridges, driving near airports, or areas with heavy electronic interference (e.g., as described in LI82.85-P-076157) can cause connection drops. Cellular Networks: Interference from nearby cell towers operating on similar frequencies (usually 2.4GHz or 5GHz) can disrupt the signal. Storage Location: Keeping your phone in a handbag or surrounded by other objects inside the vehicle can create physical or electronic interference. Device and Software Issues Head Unit Software/Hardware: Outdated firmware, bugs, or hardware faults in the vehicles head unit can prevent a stable connection. iPhone Software/Hardware: Similar issues in the iPhone, including buggy iOS updates or hardware problems, may affect performance. Reset or Reboot: Automatic rebooting or resetting of either the head unit or the iPhone will temporarily disrupt CarPlay. Connection and Settings Wired Connections: Faulty Cable: A damaged or poor-quality USB cable can cause intermittent or total loss of connection. USB Port Issues: Dust, debris, or physical damage in the USB port of either the head unit or the iPhone can also lead to disconnects. Wireless Connections: Intermittent Bluetooth/Wi-Fi: Unstable wireless communication (Bluetooth/Wi-Fi) can frequently break the Car- Play connection. Power Management: Battery Saver Mode: Enabling low power mode may restrict background processes, affecting CarPlay. Vehicles Electrical System: Unstable power delivery from the cars battery or electrical interruptions can cause the head unit to malfunction. Phone & App Configuration Phone Settings: Incorrect or conflicting settings (especially Bluetooth or Wi-Fi) on your iPhone can interfere with the CarPlay link. Third-Party Apps/Profiles: Installed apps or configuration profiles may conflict with CarPlays operation. Native apps are apple maps, apple music, audio books, apple news, podcasts, messages and phone. All other apps are considered third party apps. App Conflicts: Running conflicting apps that require similar system resources as CarPlay can cause instability. Mobile Data Plan: Streaming from online sources without sufficient mobile data can result in lost connectivity. Other Factors Heat & Overheating: If either the phone or the head unit overheats, they may disable certain functions to prevent damage, leading to disconnection. User Actions: Accidentally disconnecting the device in settings, or physically moving or bumping the phone or cable, may disrupt the connection. Remedy FUP6 (E605.8) software has been released for the following chassis: 118, 177, 243,247,206,254,167,294,295,296,223, 297. Flash available software for the head unit and test for function. The LI will be updated once available for the remaining chassis. If the complaint remains after the SW update please continue with the steps below. Guided Diagnostic Path for Apple CarPlay Connection Issues: Please follow the steps below to systematically diagnose and resolve CarPlay concerns:Update Devices: Ensure the iPhone is updated to the latest available iOS version. Ensure the vehicles head unit is updated to the latest software version available. Isolate the Issue: Check whether the symptom persists with another iPhone running the latest iOS version. Test both wireless and wired CarPlay connections: Does the issue only occur with wireless CarPlay? Does the wired connection to the phone function correctly? Further Troubleshooting Steps: Reboot the iPhone. See attachment for further instructions.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module NOTE: Occasionally to verify complaint, the steering column/vehicle needs to be in direct sunlight or hot conditions for a few hours. If noise only occurs when adjusting the steering column via electric actuation, please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on all pivot points including, but not limited to, green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, wipe excess grease off and perform greasing and movement to limit stops in all directions again. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. Include detailed items of the following: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

control unit (N112/9) is not supported for gray-market vehicles. Cause Before deactivating the HERMES control unit (N112/9), it must be clarified by the legal department of the respective MPC whether and under what conditions deactivation may be carried out. If deactivation is not permissible under applicable law, the HERMES control unit (N112/9) must not be deactivated. Remedy Please inform the customer that, following deactivation, the vehicle will no longer be able to place an automatic emergency call, nor will the customer be able to place a manual emergency call. After deactivation, the Mercedes-Benz Digital Extras will also no longer be available. Please have the attached sample form checked by your market's legal department, adapted to local requirements if necessary, and approved. Furthermore, after informing the customer about the effects of deactivation, please have the workshop complete and sign the approved form together with the customer, and send it to the MPC via a TIPS case for audit-compliant documentation. Furthermore, the workshop must affix a sticker to the emergency call button cover on the overhead control panel and to the emergency call button itself. After affixing, pictures of the overhead control panel need to be attached to the TIPS case for audit-proof documentation. After deactivation, the HERMES control unit (N112/9) is in the "Out of Service" operating status, and the display "SOS NOT READY" appears in the Audio/COMAND system. This display message tells the customer that the emergency call function is not available. In detail, the following steps must be carried out 1. The workshop must inform the customer about the effects of deactivation (see above) 2. Legal review by the MPC Legal department to determine whether deactivation is permissible for the vehicle and provision of a market-specific customer form based on the examples (see "Example - Deactivation communication module HERMES customer declaration English V3.0.pdf") 3. Completion of the market-specific customer form by the workshop and obtaining the customers signature 4. Creation of a XSS ticket by the workshop for the MPC with the signed customer form attached 5. Written confirmation of legally reviewed and approved deactivation by the MPC in the TIPS case (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, point 1) 6. Creation of an XSS ticket for documentation of the SA code "09o" (zero nine oh) in the Vehicle Documentation System (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, steps 27) 7. Ordering of stickers (part number A9078172900), quantity: 2 8. Affixing of the sticker (part number A9078172900) to the cover of the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 9. Affixing of the sticker (part number A9078172900) to the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 10. Taking photos of the applied stickers and attaching them to the TIPS case 11. After the XSS ticket has been successfully processed, the communication module must be deactivated using XENTRY: Connect XENTRY Diagnosis Access the HERMES control unit (N112/9) "Adaptation" tab, menu item "Teach-in processes" -> "Deactivation" Follow the instructions

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again and anywhere there are movement or friction points that the noise seems to be emanating from. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the Lock button", then doubleclick the Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 double-click on the locking button As of modification year 22/1, by pressing and holding the locking button + double-clicking on the release tab On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. Instrument panel support Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: Position of height and longitudinal adjustment when the noise occurs If possible, locate affected component part on steering column State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: vehicle technical issue? customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: Amperage setting of charger and time battery was on charger XENTRY Battery Tester results Voltage of battery taken with multimeter: Do not connect charger while taking measurements N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) Workshop analysis of conspicuous data Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Initial problem - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] - Delete fault memory and recheck vehicle Note - If wiring fault is found in newer vehicle, please send in a IFQ (Initial Field Quality) TIPS Case. 2. Subsequent problem after repair In this case, the workshop must perform the following operation steps: - Replace overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) - Clean electrical connectors of overhead control panel with commercially available contact cleaner and clean, purified compressed air. - Delete fault memory and recheck vehicle Note - If no remedy is found, please open a TIPS case and send to the Body/Chassis/Entertainment inbox.

In such cases, "Playback not active" is shown in the display. Cause Mute line between communication module N112/2 and sound control unit N40/3. Remedy Check the mute cable between control units N112/2 (communication module) and N40/3 (sound system). Inspect the cable and plug contacts for damage or deformation. Repair or replace the cable as needed. Important: If any plug contact is found to be deformed, you must also inspect the corresponding connector on the control unit to ensure it is not compromised.

complaints may be noted: - One or more menu selections (navigation, AMG, etc.) are missing from the instrument cluster display - The menu icons are present but the functionality does not appear in instrument cluster display after it is selected Cause - Communication between the instrument cluster control unit (N133/1) and the multifunction display (A40/16) - Incorrect instrument cluster control unit (N133/1) SCN coding Note: Some instrument cluster menu options are dependent on option code (i.e. the navigation menu option will only be present on vehicles equipped with navigation, code 365). Before Before beginning diagnosis, ensure that the vehicle is equipped with the accompanying option code Remedy If the first complaint is noted: - Perform a circuit 30 reset of the MBUX multimedia system (A26/17), the instrument cluster control unit (N133/1), and the multifunction display (A40/16). I.e. disconnect the control units from power simultaneously for 1 hour, or disconnect the ground cable for the 12V battery for 1 hour - If the above step does not remedy the complaint, perform initial start-up of the instrument cluster control unit (N133/1) with Xentry diagnosis software release 12/2019 and addon 14970 or newer - If the above steps do not remedy the complaint, perform initial start-up of the MBUX multimedia system (A26/17). Then perform a factory reset of the head unit (Settings -> System -> Reset) If the second complaint is noted: - SCN code the instrument cluster control unit (N133/1)

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465, 906 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174

our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage detection (DMTL) on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership.

CarPlay over Wi-Fi Audio cuts out Device not recognized No operation possible Cause There are multiple possible causes for an iPhone disconnecting from a vehicles head unit while using Apple CarPlay. These include hardware, software, and environmental factors: Environmental Interference External Sources: Passing under toll bridges, driving near airports, or areas with heavy electronic interference (e.g., as described in LI82.85-P-076157) can cause connection drops. Cellular Networks: Interference from nearby cell towers operating on similar frequencies (usually 2.4GHz or 5GHz) can disrupt the signal. Storage Location: Keeping your phone in a handbag or surrounded by other objects inside the vehicle can create physical or electronic interference. Device and Software Issues Head Unit Software/Hardware: Outdated firmware, bugs, or hardware faults in the vehicles head unit can prevent a stable connection. iPhone Software/Hardware: Similar issues in the iPhone, including buggy iOS updates or hardware problems, may affect performance. Reset or Reboot: Automatic rebooting or resetting of either the head unit or the iPhone will temporarily disrupt CarPlay. Connection and Settings Wired Connections: Faulty Cable: A damaged or poor-quality USB cable can cause intermittent or total loss of connection. USB Port Issues: Dust, debris, or physical damage in the USB port of either the head unit or the iPhone can also lead to disconnects. Wireless Connections: Intermittent Bluetooth/Wi-Fi: Unstable wireless communication (Bluetooth/Wi-Fi) can frequently break the Car- Play connection. Power Management: Battery Saver Mode: Enabling low power mode may restrict background processes, affecting CarPlay. Vehicles Electrical System: Unstable power delivery from the cars battery or electrical interruptions can cause the head unit to malfunction. Phone & App Configuration Phone Settings: Incorrect or conflicting settings (especially Bluetooth or Wi-Fi) on your iPhone can interfere with the CarPlay link. Third-Party Apps/Profiles: Installed apps or configuration profiles may conflict with CarPlays operation. Native apps are apple maps, apple music, audio books, apple news, podcasts, messages and phone. All other apps are considered third party apps. App Conflicts: Running conflicting apps that require similar system resources as CarPlay can cause instability. Mobile Data Plan: Streaming from online sources without sufficient mobile data can result in lost connectivity. Other Factors Heat & Overheating: If either the phone or the head unit overheats, they may disable certain functions to prevent damage, leading to disconnection. User Actions: Accidentally disconnecting the device in settings, or physically moving or bumping the phone or cable, may disrupt the connection. Remedy Guided Diagnostic Path for Apple CarPlay Connection Issues Please follow the steps below to systematically diagnose and resolve CarPlay concerns: Update Devices: Ensure the iPhone is updated to the latest available iOS version. Ensure the vehicles head unit is updated to the latest software version available. Isolate the Issue: Check whether the symptom persists with another iPhone running the latest iOS version. Test both wireless and wired CarPlay connections: Does the issue only occur with wireless CarPlay?

message "SOS - Service not activated" is displayed in the instrument cluster. Cause The message "SOS - Service not activated" tells the customer that "over-the-air" registration of the vehicle with the Mercedes Intelligent Cloud is not possible. On a gray import vehicle, this is due to the fact that the SIM card installed in the HERMES communications module cannot dial into the mobile phone network in the importing country. Remedy The only way of avoiding the message in the instrument cluster is to deactivate the HERMES module using the 09o deactivation process after obtaining the customer's consent. After deactivation, the HERMES control unit (N112/9) has the operating status "Inoperative". The message "SOS not ready" appears in the audio/COMAND display (A40/8) and may also appear in the instrument cluster. This display message tells the customer that the emergency call function is not available. In addition, the workshop must attach a label (2 x part number A9078172900 required) to the cover of the emergency call button in the overhead control panel and to the emergency call button itself. Replacing the hardware of the HERMES communication module is not effective.

Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled "New onboard electrical system diagnosis shown on BR 166". The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: vehicle technical issue? customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge, create a TIPS case. -Must include with the case: Amperage setting of charger and time battery was on charger XENTRY Battery Tester results Voltage of battery taken with multimeter: Do not connect charger while taking measurements N10/6 FSAM and N73/3 EZS CUL Workshop analysis of conspicuous data Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) NOTE: For expedited results when creating a case write customer complaint as "XENTRY Battery Tester implausible".

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Test: Please perform the new SCN coding for HOSWD control unit (N179/1) (available since May 2025). Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> Please create TIPS case! If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no fault is visible: Please open a TIPS case! In the event of a customer complaint and further fault code in HOSWD: B1E7713: Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). B1F1F04: Check hand detection system control unit; if necessary swap with donor vehicle (ensure that the HW part numbers are identical).

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Test: Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Reset the HOSWD control unit in line with the guided test in Xentry. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> replace steering wheel rim. If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no defect is visible: Please do not replace the steering wheel, but wait for new coding parameters which should be available 05/2025. Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. B1E7713: Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is now available for Star 3 vehicles only. Fault in IDC223 control unit: U186B29: Delete fault memory and flash the new IDC (N62/4) software A223 902 75 37. If the software update is not available, or the problem persists, create a TIPS case. Fault in IDC213 control unit: U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the HOSWD control unit then scan the steering wheel and check whether the fault is reproducible. If reproducible: Create a TIPS case, adding the

Cause Temperature sensor in overhead control panel (OCP) delivering incorrect values: The temperature sensor in the overhead control panel is malfunctioning. Fault code B110709 or fault code B11F697 are present in the overhead control panel with the status (active) or (active stored). or The temperature sensor in the overhead control panel measures an incorrect temperature (the temperature value can be checked against the actual value in the overhead control panel) If the above-mentioned fault code is not present, the cause could be malfunction on the air conditioning system. Remedy If one of the above-mentioned fault codes should occur, a TIPS case must be created here. If the above fault codes or actual value differences are present in the OCP - please send the case to the Body/Chassis/ Entertainment inbox. Otherwise, the case must be sent to the HV/LV inbox for support in A/C diagnosis. *** It is not necessary to replace the overhead control panel ***

Applicable fault codes on front right tire pressure sensor, see table "Control unit/fault code". Cause Coaxial cable from instrument cluster to instrument cluster control unit (under driver's seat) damaged. Remedy Check coaxial cable from display cluster for head unit/instrument cluster (A26/17 or A40/16 - depending on equipment variant) to head unit/display cluster control unit (N133/1 or N166). If the plug contact of the coaxial cable or the connector housing connection is faulty, replace coaxial cable (see XPI).

communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit.

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Enter AO Code O19 into VeDoc (O for Oscar, not "zero") 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 double-click on the locking button As of modification year 22/1, by pressing and holding the locking button + double-clicking on the release tab On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer.

CLA, CLS, E-Class, G-Class, GLA, GLB, GLC, GT, and S-Class (118, 177, 205, 213, 217, 222, 238, 247, 253, 257, 290, 463 platform) vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update. Parts Parts are not required

CLA, CLS, E-Class, EQB, GLB, GLE, GLS, AMG GT 4-Door, and S-Class (118, 167, 177, 205, 213, 222, 238, 243, 247, 257, 290 platform) vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

control units FSCM_GEN4/5/6 For these fault codes, the tests contained in XENTRY must be carried out P046109 / P206609 / P13E600 For these fault codes, the connector couplings/wiring harness routing must be checked for damage P206600 / P046100 Cause Various Remedy Carry out XENTRY tests for the listed fault codes in the FSCM (N118) and document the monitor graphics for the primary/ secondary lever-type sensors.

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware ISU = Initial Start Up LVDS = Low Voltage Differential Signal NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465, 906 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" No vehicles currently launched.

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. B1E7713: Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is now available for Star 3 vehicles only. Fault in IDC223 control unit: U186B29: Delete fault memory and flash the new IDC (N62/4) software A223 902 75 37. If the software update is not available, or the problem persists, create a TIPS case. Fault in IDC213 control unit: U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the HOSWD control unit then scan the steering wheel and check whether the fault is reproducible. If reproducible: Create a TIPS case, adding the note "reproducible". If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. New coding parameters (SCN) will be available in Q2/2025 for the HOSWD control unit.

We hope that you're enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air ("OTA") Service Campaign to update the communication module software on certain Model Year 2019-2025 A-Class, C-Class, CLA, CLE, CLS, E-Class, EQB, EOE, EQS, G-Class, GLA, GLB, GLC, GLE/GLS, AMG GT 4-Door, and S-Class vehicles. This update includes quality-enhancing optimizations and product improvements.

If you have symptoms with one or both displays, a TIPS case must be created. The TIPS case will be reviewed by MBUSA and GCSP. NOTE: Please perform the following steps before creating a TIPS case: Step 1: Check software release of the following control units to see if they are up to date; if necessary perform software update. Instrument cluster (IC177 / IC 177M) Head unit (HU6 / HU7) All displays (DISP6 / DISP7S2) Reassess for the symptom. If the symptom is still present, continue with step 2. Step 2: Perform swap (swap display with a display from a reference vehicle) and reassess for the symptom. If the problem relates to the display, replace display. If the problem does not relate to the display, continue with step 3. Step 3: Check electrical wiring harness and video line (LVDS) for routing and external damage. Check contact pins and contact sockets for corrosion and bonding (photo documentation in micro view format requested). Check electric wiring harness for conductivity and short circuit, document measurement results in a measurement report or referenced wiring diagram using the CDT four level model. If the wiring harness and the video line is OK, please complete the attached questionnaire, create TIPS case according to list of requirements. Please add the following documents to the TIPS case: Video of problem Completed questionnaire Current quick test with freeze frame results Measurement report and photo documentation of wiring harness Control unit log of head unit Control unit log of instrument cluster Control unit log of display cluster Log-files HU-logging (password via TIPS case) NOTE: Make sure to document the original customer complaint. NOTE: Please refer to this LI in the warranty claim in the "Notes" section. The damage code of the component determined to be the root cause of the symptom must be used in the warranty claim.

Please note that if the complaint "Fuel filler flap not opening" occurs, it is important to check the fuel filler flap before replacing the central locking actuator. For gasoline hybrid vehicles where the fuel filler flap fails to open or does so but slowly, observe the document "Fuel filler flap fails to open or does so but slowly on plug-in HYBRID gasoline vehicles"! Cause Central locking actuator may have an electrical fault and may not open. Remedy 1. Car locked: To rule out incorrect operation, operate the fuel filler flap in the area shown in Fig. 1 and listen out for the clicking noise of the microswitch in the central locking actuator. If no clicking can be heard, continue with point 4. 2. Car unlocked: Press area on flap to start the microswitch clicking. Flap opens - show the customer the area to press. 3. Car unlocked: Flap cannot be opened regardless of which area you press. Open the flap by operating the emergency release for the CL actuator (through trunk, fender gap cover, etc, depending on specific vehicle) 4. Central locking actuator pressed directly, no clicking of microswitch, no electrical release of central locking actuator => Clicking of microswitch, electrical release of central locking actuator => Tank filler recess/charging recess not OK; report results via a TIPS case to B/C/E Inbox. 5. Replace central locking actuator; check function of new part before installing it: Do not dispose of damaged part. New central locking actuator does not release: More detailed examination of connector coupling, wiring harness, electrics required.

control units FSCM_GEN4/5/6 For these fault codes, the tests contained in XENTRY must be carried out P046109 / P206609 / P13E600 For these fault codes, the connector couplings/wiring harness routing must be checked for damage P206600 / P046100 Cause Various Remedy Carry out XENTRY tests for the listed fault codes in the FSCM (N118) and document the monitor graphics for the primary/ secondary lever-type sensors.

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. B1E7713: Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is now available for Star 3 vehicles only. Fault in IDC223 control unit: U186B29: Delete fault memory and flash the new IDC (N62/4) software A223 902 75 37. If the software update is not available, or the problem persists, create a TIPS case.

If you have symptoms with one or both displays, a TIPS case must be created. The TIPS case will be reviewed by MBUSA and GCSP. NOTE: Please perform the following steps before creating a TIPS case: Step 1: Check software release of the following control units to see if they are up to date; if necessary perform software update. Instrument cluster (IC177 / IC 177M) Head unit (HU6 / HU7) All displays (DISP6 / DISP7S2) Reassess problem. If the problem is still present, continue with step 2. Step 2: Perform swap (swap display with a display from a reference vehicle) and reassess problem. If the problem relates to the display, replace display. If the problem does not relate to the display, continue with step 3. Step 3: Check electrical wiring harness and video line for routing, breakovers and external damage. Check contact springs and contact sockets for corrosion and bonding (photo documentation in micro view). Check electric wiring harness for conductivity and short circuit, document measurement results in a measurement report or referenced wiring diagram using the CDT four level model. If the wiring harness and the video line is OK, please complete the attached questionnaire, create TIPS case according to list of requirements. Please add the following documents to the TIPS case: Video of problem Completed questionnaire Current quick test with freeze frame results Measurement report and photo documentation of wiring harness Control unit log of head unit Control unit log of instrument cluster Control unit log of display cluster Log-files HU-logging (password via TIPS case) NOTE: Make sure to document the original customer complaint. NOTE: Please refer to this LI in the warranty claim in the "Notes" section. The damage code of the component determined to be the root cause of the symptom must be used in the warranty claim.

and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 01.06.2023 (Send to Body/Chassis/Entertainment Inbox) - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 01.06.2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.

and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.

"Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.

Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button

C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.

We hope that youre enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air (OTA) Service Campaign to update the Communication Module software on certain Model Year 2020-2023 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, and S-Class vehicles. This update will improve the system stability and allow for better accessibility of Mercedes me services. This OTA update will be provided free of charge and will be performed in the background. No action is needed on your behalf. Your vehicle does not appear to have an active Mercedes me connect subscription. In this case, the OTA update will be performed unless you choose to opt-out from receiving this OTA update. What will your Dealer do? NO DEALER ACTION IS NECESSARY for this OTA update. You do not need to visit a Mercedes-Benz dealer. Opting-out of this OTA Update: Customers who are not subscribed to the Mercedes me connect service may opt-out of this OTA update by emailing or by calling 1-800-FOR-MERCEDES. The opt-out period will start on January 5, 2024 and end on February 4, 2024. If you choose to opt-out, the described update will not be available for your vehicle as an additional workshop measure. No action is necessary for Opting-In. Once the opt-out period has closed on February 4, 2024, this OTA will be automatically downloaded and installed. Thank you for allowing us to continue taking care of your vehicle.

A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.

and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case - Open a TIPS case for vehicles: As of manufacturing date 01.02.2022, except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa As of manufacturing date 01.08.2022 and production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] 3. Remedy for vehicles prior to manufacturing date 01.02.2022 (except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) or 01.08.2022 (production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.

Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!

steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.

C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customers vehicle. The OTA may be validated as successful on the customers Mercedes Me connect app under Over-the-Air Vehicle Updates as Update for the communication module. If the OTA is successful it will show a green installed and date of installation in the Over-the-Air update section.

After the next ignition cycle, the ambient lighting functions again correctly. Cause Software in coupling elements (EKE) faulty. The coupling element software cannot be updated in After-Sales. Remedy In a complaint case, replace the respective wiring harness (coupling elements are installed on the wiring harness) for ambient lighting.

- Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. - Instrument panel support - Steering column switch module If the cause of the noise can be narrowed down to the steering column, create a PTSS case

CLA-Class, GLA-Class, GLE-Class, GLS-Class, A-Class, C-Class, E-Class, GLB-Class, CLS-Class, and AMG GT 4-doors/Coupe (118, 167, 177, 190, 213, 238, 247, 257, and 290 platform). The possibility exists that the information regarding radar sensor MMRV1 may be incorrect, and therefore the printed operators manual may not align with the internal vehicle specifications. What Were Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will check and replace the printed operators manual, if necessary.

enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage Detection ("DMTL") on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership. Why the Warranty extension? On certain Model Year 2018 - 2024 A / C / CLA / CLS / E / G / GLA / GLB / GLC / GLE / GLS / GT / S / SL Mercedes-Benz vehicles, under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code ("DTC") entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp ("MIL"). Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be covered under this extended warranty and performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

illuminated Shifts into N Concern disappears after ignition cycle When performing a quick test, the following fault code is stored in Y3/14 Transmission control for 8speed dualclutch transmission (DKG): P056300 The onboard power supply voltage is too high. Cause An overvoltage condition is detected exclusively within the transmission control unit, storing fault P056300 once the measured voltage exceeds 16V. Remedy This LI applies if the freeze frame data for P056300 show a supply voltage between 15.75 to 16.50 volts, and no other control units report overvoltage. (figure 1) Long Term Resolution: Software resolutions have been released. Check validity and ensure your Xentry is updated with latest Addons before continuing: 1. Perform software update for Y3/14 Transmission control for 8speed dualclutch transmission (DKG) available software listed in Parts 2. Clear fault memory and perform final test drive If the customer complaint matches this LI and the software currently installed on the vehicle is not listed, please submit a TIPS case to the Powertrain inbox with the following information: Initial Quick Test w/ Freeze Frame Data DKG Control Unit Log Latest EEPROM data Screenshot of software availability

illuminated Shifts into N Concern disappears after ignition cycle When performing a quick test, the following fault code is stored in Y3/14 - Transmission control for 8-speed dual-clutch transmission (DKG): P056300 The on-board power supply voltage is too high. Cause An overvoltage condition is detected exclusively within the transmission control unit, storing fault P056300 once the measured voltage exceeds 16V. Remedy This LI applies if the freeze frame data for P056300 show a supply voltage between 15.75 to 16.50 volts, and no other control units report overvoltage. (figure 1) Long Term Resolution: Software resolutions are being rolled out for various models. Check validity and ensure your Xentry is updated with latest Addons before continuing: 1. Perform software update for Y3/14 - Transmission control for 8-speed dual-clutch transmission (DKG) - available software listed in Parts 2. Clear fault memory and perform final test drive Short Term Resolution: Please clear faults and perform an extended test drive. The vehicle may be released to the customer until software is available. If the customer complaint matches this LI and the software currently installed on the vehicle is not listed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial Quick Test w/ Freeze Frame Data - DKG Control Unit Log - Latest EEPROM data - Screenshot of software availability

In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (MIL).

Emergency Stop Assist not available" "Active Lane Keeping Assist not available" "Active steering assist not available" Cause Possible causes: Hand detection mat, hand detection control unit, contacts, and electrical feed line. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Check: Please do not replace the HOSWD control unit. Please flash the new SW and perform the SCN coding for the HOSWD control unit (N179/1) (available from July 2026). The software can be flashed onto all HOSWD213 with HW number A0009011522 and all HOSWD223 with HW number A0009011422. Please also flash the SW for the IDC control unit (N62/4), if possible (only applies to HOSWD223). Erase fault memory Remedy: Turn on the ignition or start the engine without touching the steering wheel. If, after 10 seconds without touching the steering wheel, one of the three fault messages appears on the instrument cluster: Check the contacts and feed lines in the steering wheel by means of a visual inspection for damage, crimp connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace the steering wheel electronics or the feed lines. If there is not any visible damage -> replace the steering wheel rim. If a yellow message does not appear on the instrument cluster within 10 seconds: Grasp the steering wheel fully with both hands, including the chrome molding at the 6 o'clock position (see picture 1). If the fault is triggered by grasping the steering wheel rim or pressing the clip at the 6 o'clock position, check the contacts and feed lines in the steering wheel by means of a visual inspection for damage, kinked connections, loose connections, etc. (example in picture 2 and 3). Check the ground connections (screw connections and cables to the steering wheel rim); if necessary, retighten the screws/bolts and check for corrosion (picture 4). If there is visible damage -> replace the steering wheel electronics or the feed lines. If there is not any visible damage: Replace the steering wheel rim. Please do not replace the HOSWD control unit. A TIPS case should be created if fault profile is unclear. In the event of a customer complaint and a further fault code in HOSWD: B1E7713: Check the ground connections (screw connections and cables to the steering wheel rim); if necessary, retighten the screws/bolts and check for corrosion (picture 4). B1F1F04: Check the control unit of the hand detection system; if necessary, replace this with the control unit from a donor vehicle (make sure that the hardware part numbers are identical).

Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

-Engine runs rough. -Poor shifting or jerking when accelerating. -Fault codes stored related to mixture formation, injector quantity adjustment, or misfire. Note: One or more of the above symptoms can occur. It is possible that no fault codes are stored. Cause Leaking valve seat in cylinder head. Remedy -Perform cylinder leakage check as noted in WIS group 01.00. If excessive leakage is found determine if leak is from intake or exhaust valves. -If leakage is found from intake or exhaust valves, remove cylinder head and inspect valve seats. -The complete cylinder head must be replaced if valve seat damage is found. The valve seats can not be reworked. -Engine oil and filter should be changed after the repair. Workshop notes cylinder head repair: 1. The intake rocker arm roller is narrower than the exhaust and they must not be interchanged. Mark the rocker arms so they are reinstalled in their original location. 2. Inspect all parts that are being reused (i.e. camshafts, rocker arms) for signs of wear or damage. See WIS doc AH05.20-P-1000-09SZ for examples of normal and abnormal wear. Replace parts with new if damage or wear is found. 3. Check that all rocker arms are correctly located on the camshaft before installing cylinder head cover. Rotate engine at least 2 times and check that there are no problems with rocker arms. 4. The timing chain tensioner can be reused if it extends fully, has no noticeable problems in prior operation, and no chain drive components were replaced. 5. Care must be taken when removing fuel injectors to prevent damage. See WIS doc AR07.03-P-0004-03MM. 6. Cleanliness must be observed during repair to prevent subsequent complaint or engine damage: When cleaning engine block surface, ensure oil ports are sealed to prevent debris from entering oil circuit. Refer to SI01.40-P-0010A. No abrasive materials, sharp-edged tools, or unapproved cleaners should be used on engine block surface. Refer to AR01.00-P-0050-01A. Any debris from cleaning that has entered the cooling jacket should be removed before assembly of engine. The debris can otherwise cause blockage in the cooling circuit leading to engine overheating. If any of the parts listed below are found damaged or in need of replacement during cylinder head valveseat diagnosis or repair, and the vehicle has warranty coverage, they must be claimed on a separate partsonly line. These items are not covered under the cylinder head warranty extension and cannot be included with the claim. Camshafts Camshaft adjustment solenoids Camshaft positioners Fuel injectors Hydraulic valve play compensating elements Roller rocker arms Spark plugs Timing chain Timing chain guide rails

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% a negative charge balance A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked). Vehicles with code B01+801: When charging while stationary, the 48V battery must have a state of charge (SOC) of 70% before the 12V primary battery, or the secondary battery in the case of code 503, can be charged. To ensure optimum battery care, please also comply with the existing Service Information documents regarding the handling of stock vehicles (SI54.10-P-0024A) and on remaining in transport mode (SI54.00-P-0004A) until immediately before handover to end customers. Special note: Do not replace any parts, if the message has occurred due to battery discharge as a result of the driving profile or the ignition being switched on (see attached examples); in such cases separate warranty and goodwill invoicing is not possible, as this is a normal on-board electrical system protection function. Likewise battery care and recharging do not qualify as a W&G case. Please advise customers accordingly regarding the above-mentioned issues relating to vehicle use.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

-Engine runs rough. -Poor shifting or jerking when accelerating. -Fault codes stored related to mixture formation, injector quantity adjustment, or misfire. Note: One or more of the above symptoms can occur. It is possible that no fault codes are stored. Cause Leaking valve seat in cylinder head. Remedy -Perform cylinder leakage check as noted in WIS group 01.00. If excessive leakage is found determine if leak is from intake or exhaust valves. -If leakage is found from intake or exhaust valves, remove cylinder head and inspect valve seats. -The complete cylinder head must be replaced if valve seat damage is found. The valve seats can not be reworked. -Engine oil and filter should be changed after the repair. Workshop notes cylinder head repair: 1. The intake rocker arm roller is narrower than the exhaust and they must not be interchanged. Mark the rocker arms so they are reinstalled in their original location. 2. Inspect all parts that are being reused (i.e. camshafts, rocker arms) for signs of wear or damage. See WIS doc AH05.20-P-1000-09SZ for examples of normal and abnormal wear. Replace parts with new if damage or wear is found. 3. Check that all rocker arms are correctly located on the camshaft before installing cylinder head cover. Rotate engine at least 2 times and check that there are no problems with rocker arms. 4. The timing chain tensioner can be reused if it extends fully, has no noticeable problems in prior operation, and no chain drive components were replaced. 5. Care must be taken when removing fuel injectors to prevent damage. See WIS doc AR07.03-P-0004-03MM. 6. Cleanliness must be observed during repair to prevent subsequent complaint or engine damage: When cleaning engine block surface, ensure oil ports are sealed to prevent debris from entering oil circuit. Refer to SI01.40-P-0010A. No abrasive materials, sharp-edged tools, or unapproved cleaners should be used on engine block surface. Refer to AR01.00-P-0050-01A. Any debris from cleaning that has entered the cooling jacket should be removed before assembly of engine. The debris can otherwise cause blockage in the cooling circuit leading to engine overheating. If any of the parts listed below are found damaged or in need of replacement during cylinder head valveseat diagnosis or repair, and the vehicle has warranty coverage, they must be claimed on a separate partsonly line. These items are not covered under the cylinder head warranty extension and cannot be included with the claim. Camshafts Camshaft adjustment solenoids Camshaft positioners Fuel injectors Hydraulic valve play compensating elements Roller rocker arms Spark plugs Timing chain Timing chain guide rails Timing chain tensioner

"P0A7F00" stored in the 48 V battery G1/3 and/or is current. Remedy Update the 48V battery to SW 25/12 A0019020424 Then perform the following measures: - Switch on ignition - Read out actual value 209 in XENTRY Diagnosis for G1/3 (48 V battery) "State of Health Capacity-SOHC" -- If the value > 80% doesn't require a healing process -- If the value is < 80%, continue with the following steps Carry out capacity healing procedures: - Discharge 48 V battery in vehicle with ignition "On" and check the SOC of the 48 V battery in the workshop menu of the instrument cluster - At SOC <30%: Stop discharge and lock vehicle - with key out of range; (Bus idle) -Charging the 48V battery - When SOC reaches or exceeds 70%, stop charging and lock the vehicle with the key out of range; (bus idle) - After 1.5h bus idle: Switch on ignition Read out actual value 209 in XENTRY Diagnosis in the G1/3 (48 V battery) "State of Health Capacity-SOHC" - SOH > 90%: Procedure is finished and fault memory erased - SOH < 90%: Repeat the steps again. If the value is still too low after 5 repetitions: Abort healing process and open a TIPS case.

and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

"P0A7F00" stored in the 48 V battery G1/3 and/or is current. Remedy Update the 48V battery to SW 25/12 A0019020424 Then perform the following measures: - Switch on ignition - Read out actual value 209 in XENTRY Diagnosis for G1/3 (48 V battery) "State of Health Capacity-SOHC" -- If the value > 80% doesn't require a healing process -- If the value is < 80%, continue with the following steps Carry out capacity healing procedures: - Discharge 48 V battery in vehicle with ignition "On" and check the SOC of the 48 V battery in the workshop menu of the instrument cluster - At SOC <30%: Stop discharge and lock vehicle - with key out of range; (Bus idle) - After 1.5h bus idle: Switch on ignition Read out actual value 209 in XENTRY Diagnosis in the G1/3 (48 V battery) "State of Health Capacity-SOHC" - SOH > 90%: Procedure is finished and fault memory erased - SOH < 90%: Repeat the steps again. If the value is still too low after 5 repetitions: Abort healing process and open a TIPS case.

The concern of transmission limp-home mode disappears after the ignition is switched off and on again. P092500 The shift valve of the hollow shaft has a malfunction. _ is present in the DKG Control Unit (Y3/14n4), and the extended freeze frame data shows hex code 25 F2 (see attachments for reference) Cause Hydraulic fault caused by the transmission software. The engagement of 2nd gear by preselection after 4-3 downshift does not function due to activation fault. Remedy Check the transmission software level and follow the steps below: You can use the EEPROM as txt file for Program version (see attachments for reference) 18a software: Flash transmission control unit Y3/14nY with latest software using Xentry, version 09/2021 or 12/2021 and all add-ons (except model designations 118.351, 118.651, 177.051, 177.151, 177.951); delete fault memory. 18b software: Flash transmission control unit Y3/14nY with latest software using Xentry, version 12/2023 and all add-ons If there is no software available for the DKG Control Unit, or the concern is still present after the software update: Please submit a TIPS case to the Powertrain Inbox and include the following information: - Initial Quick Test w/ Freeze Frame Data - DKG Control Unit Log - Guided Test result for P092500 - Initial EEPROM (before performing any adaptations) - Current EEPROM data

"P0A7F00" stored in the 48 V battery G1/3 and/or is current. Remedy Update the 48V battery to SW 25/12 A0019020424

our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (MIL).

"P0A7F00" stored in the 48 V battery G1/3 and/or is current. Remedy Perform guided test for fault code "P0A7F00". Important! To ensure a bus idle of 90 minutes is achieved, the vehicle should be locked and the key placed a minimum of 30 feet from the vehicle) See SI82.85-P-0046A

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

"P0A7F00" stored in the 48 V battery G1/3 and/or is current. Remedy Perform guided test for fault code "P0A7F00". Important! To ensure a bus idle of 90 minutes is achieved, the vehicle should be locked and the key placed a minimum of 30 feet from the vehicle)

"P0A7F00" stored in the 48 V battery G1/3 and/or is current. Remedy Perform guided test for fault code "P0A7F00". Important! To ensure a bus idle of 90 minutes is achieved, the vehicle should be locked and the key placed a minimum of 30 feet from the vehicle) See SI82.85-P-0046A

"P0A7F00" stored in the 48 V battery G1/3 and/or is current. Remedy Perform guided test for fault code "P0A7F00". Important! To ensure a bus idle of 90 minutes is achieved, the vehicle should be locked and the key placed a minimum of 30 feet from the vehicle) See SI82.85-P-0046A

code "P0A7F00" stored in the 48 V battery G1/3 and/or is current. Remedy Perform guided test for fault code "P0A7F00". Important! To ensure a bus idle of 90 minutes is achieved, the vehicle should be locked and the key placed a minimum of 30 feet from the vehicle) See SI82.85-P-0046A

and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.

One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.

Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.

occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

Adaptation and misfire faults may also be stored. Vehicle may enter limp home mode. Cause False detection of rail pressure sensor out of range. Remedy Update software of engine control module N3/10. Reset mixture adaptation and clear fault codes.

Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the Fuel System Control Module (FSCM) software on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 1 S year: / 150,000 mile: (whichever occurs: first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2019 - 2021 A/CLA/ GLA/GLB/ GLE and GLS-Class vehicles, the FSCM software for the fuel pressure sensor and temperature plausibility checks may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ('MIL') might illuminate. Any repair: under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.

software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).

our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the exhaust valve system in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first). This extended warranty applies to the condition described below that may necessitate the repair or replacement of components related to the exhaust valve assembly (e.g. exhaust valve, cylinder head). The valve guide and/or seat ring may wear over time due to increased lateral forces during operation. This could potentially cause combustion misfire for cylinder 1 through 4, resulting in an activation of the check engine Malfunction Indicator Lamp (MIL). Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information, and may be audited. P030085 Combustion misfire has been detected P030x85 Cylinder x misfire detected. (x = the affected cylinder) P1CEF85 - Injector injection quantity adjustment for cylinder balancing has almost reached the upper limit value at atleast one cylinder. P1CE577 - Injector injection quantity adjustment for uniform mixture formation has detected an excessively lean mixture at atleast one cylinder. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Codes: 01201 Cylinder Head 05202 Exhaust Valve 01205 Valve seat ring exhaust valve 01206 Valve Guide Exhaust Valve

Noise may lessen as engine reaches operating temperature. Attachments File Description M260 noise.mp4 Noise example Cause Harmonics from timing chain drive. Remedy Replace timing chain tensioner with part A2600502000. Note: This noise will not cause damage to the engine or other symptoms. The chain tensioner should only be replaced in the event of a customer complaint.

Start Engine - see Operator's Manual Cause Root cause is a bus keepawake in either the Headlight control unit or in one of the following: ALC, IC, SAM, PTCU, ESP. Additionally, the quick test will show U116000 &#34;A bus keepawake control unit has been detected&#34; in the electronic ignition switch (EZS) control unit for this root cause. Remedy Eliminate bus keep awake issue flash new software where available:

Important: On vehicles with standard sound, the rear subwoofer (H21/35) emits the engine sound only (if equipped with M139 engine) On vehicles with code 853 (Advanced Sound) or 810 (Premium Sound), the rear subwoofer (H21/35) emits not only the engine sound, but also entertainment sound Remedy Perform a software update of the sound amp (N40/3) to the latest available version. Note: Do not replace any parts as this will not remedy the complaint.

This only occurs if the first Remote Start via the Mercedes me App was canceled and then started again. If the first attempt was stopped by unlocking the doors or if the engine ran for more than 10 minutes, then the second attempt is also successful

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10P067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. Please update the Head unit software to E505.9

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.

menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.

The UI continues to show the old stations artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The robustness measure has been identified and is planned for implementation in the A26/17 E505.9 software. The E505.9 software is expected to be available in XENTRY Q3 2026.

The UI continues to show the old stations artwork instead of updating to the new one. Cause Root cause currently being investigated. Remedy Please do not replace any parts. Please create a TIPS case to Body/Chassis/Entertainment inbox.

the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.

Cause Under Analysis Remedy 1.Reset the MBUX language (e.g., if the MBUX language is set to English, please change it to any other language and then set it back to English again) 2.If the issue still persists after the step 1, Perform a user data reset of the Head Unit. If the above 2 steps still don't repair the issue, please open a TIPS case. Note: Please do not replace any parts

the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

multifunction display of the instrument cluster while driving (see picture in attachment). Cause For vehicles with HERMES 3.0, A2389015700 A2389015800 A2389018400 A2389018900 A2389019000 A2389019800 A2579011200 A2579012100 the above-mentioned message is sporadically displayed in the instrument cluster once the over-the-air update to software release E843 (Software part number A2389022409) has been performed. The coding was performed incompletely here. Remedy A relevant over-the-air software update campaign for the control unit N112/9 (HERMES) is in preparation. If the vehicle is already on site, the problem can be rectified by manually commissioning the control unit N112/9 (HERMES) with XENTRY: XENTRY. "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

multifunction display of the instrument cluster while driving (see picture in attachment). Cause On vehicles with HERMES 3.0 currently, A2389015700 A2389015800 A2389018400 A2389018900 A2389019000 A2389019800 A2579011200 A2579012100 The above-mentioned message is sporadically displayed in the instrument cluster once Remedy Please manually commission the control unit N112/9 (HERMES) using XENTRY: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit" Invoice the required work using damage code 8251M/01 (damage location/damage type).

multifunction display of the instrument cluster while driving (see picture in attachment). Cause On vehicles with HERMES 3.0 currently, A2389015700 A2389015800 A2389018400 A2389018900 A2389019000 A2389019800 A2579011200 A2579012100 the above-mentioned message is sporadically displayed in the instrument cluster once the over-the-air updates to software release E843 (software part number A2389022409) have been performed. The issue is currently being analyzed; the cause is still unclear. Remedy Please manually commission the control unit N112/9 (HERMES) using XENTRY: XENTRY. "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit" Invoice the required work using damage code 8251M/01 (damage location/damage type).

Cause Without active navigation (code 365), MBUX cannot assign and install the regional database of the station logos. Remedy There is no remedy available. The function is not supported and therefore considered normal operation.

the vehicle is displayed as being in the middle of the ocean. Note: In the quick test, no relevant DTC is displayed for this. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the connector into the GNSS connection and ensure that the connector has engaged correctly and is fully seated.

B19C804 "Software tampering has been detected. There is an internal fault". </p> <p> </p> <p> Note: If there are no relevant customer complaints, then the DTC can be ignored as it does not directly affect functionality. If there is a customer complaint in addition to the above DTC, further diagnostic measures must be performed. </p> Cause The current software release of the MBUX multimedia system (A26/17) Remedy <p>Update the A26/17 to newest available software release.</p><p> </p><p>Note: Do not replace any parts.</p>

Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.

connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.

See attached picture for example. Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.

Temperature setting in Mmc mobile application settings incorrect Remedy Adjust the setting in the Mercedes me connect app via mobile phone (settings -> units)

Stations&#34; or a different category. Sometimes, the &#34;My Favorites&#34; category will be unavailable for the entire drive cycle. Cause Current MBUX Multimedia System (A26/17) software release Remedy Software update of MBUX Multimedia System (A26/17) to E905.4 (in development). This document will be updated once the software is released.

show the following message: "Map data does not match with your system. Please insert a medium containing the corresponding map data". the navigation menu cannot be opened "Activating..." is displayed beneath the navigation icon in the main menu or above the map display "Traffic Sign Assist Inoperative" message in the instrument cluster display The map data update cannot be carried out (on vehicles with code 2U0 car2go) Cause Navigation database was not successfully activated Remedy Perform the proposed measure in order to remedy the complaint: Ensure the MBUX multimedia system (A26/17) software is up-to-date (E870.9 or newer) Perform a user data reset ("Settings" -> "System" -> "Reset" in the MBUX display). Check functionality. If the complaint remains then continue with next steps Open the Dealer menu by pressing and holding down the "Home" and "Radio/Media" buttons simultaneously for approximately 8 seconds When in the Dealer menu, select "Navigation" - Then select "Delete MapData" Close the Dealer menu and reinstall the currently available NTG6 map data version from Download Manager COMAND/Hard-Disk navigation via USB Perform SCN coding of the MBUX multimedia system (A26/17) Check navigation functionality

(177 platform), CLA-Class (118 platform), CLS-Class (257 platform), E-Class (213 and 238 platform), GLA-Class, GLBClass (247 platform), GLC-Class (253 platform), GLE-Class, GLS-Class (167 platform), and GT-Class (290 platform) vehicles, the software for the MBUX control unit does not correspond with the latest series production configuration, and subsequently, navigation may not be available. What Were Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the MBUX control unit software.

Please insert a medium containing the corresponding map data". the navigation menu cannot be opened.

while attempting to communicate with the MBUX multimedia system (A26/17)

May be most noticeable when transitioning from a coasting condition to accelerator pedal application. May occur in all drive modes. Cause Dualclutch transmissions (DCT) inherently exhibit more dynamic shifting behavior compared to other types of transmissions. This is due to the use of physical clutches for starting and gear changes. In certain situations, dynamic driving behavior can lead to a slight jerk sensation which is a normal technical characteristic of the transmission. A typical example is a "Change of Mind" situation: The customer is coasting towards a red traffic light. The traffic light turns green while the vehicle is still coasting. The customer then presses the accelerator pedal. In these situations, a slight jerk may occur briefly because the transmission must quickly engage the appropriate gear and control the clutches accordingly. Since shift forks are responsible for engaging the gears during shifting, a slight shifting noise may also be noticeable. Please note driving programs S, S+, and M are designed to provide sportier vehicle behavior and are not optimized primarily for maximum comfort, so this operation may be more audible. Remedy Verify the customer's concern and confirm proper transmission operation. If no faults or abnormal operating conditions are identified by IPR (Intelligent Predictive Repair), no hardware replacement is necessary. Inform the customer that the transmission has been designed to provide direct gear engagement and responsive vehicle performance. Under certain operating conditions, brief shift sensations may be perceptible and are consistent with the operating characteristics of the dualclutch transmission

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CPR = Car Package Release (For MB.OS) CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 906 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465 907 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) Star 3.5 174 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174 178

Commonly used acronyms in LI's and TIPS cases. Control unit names, numbers, and how to identify. Network/wiring architecture groups to baumuster quick reference. Platform to baumuster quick reference. Cause Information only Remedy Acronyms: AV = Actual Values CU = Control Unit CUL = Control Unit Log DTC = Diagnostic Trouble Code E-Stand = Fresh-up head unit boot software (found in head unit control unit log) FUP = Fresh-up FW = Firmware HSVL = High Speed Video Line HU = Head Unit HW = Hardware IPD = Injector Performance Data ISU = Initial Start Up LVDS = Low Voltage Differential Signal NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) NSFT = Not Safe For Transport MOPF = Model Facelift (Ex: 167 MOPF) PiH = Plug-in Hybrid P3 Hybrid = AMG Plug-in Hybrid with rear drive unit SA Code = Sonderausstattungscode (Option Code) SCN = Software Calibration Number SW = Software TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) QT = Quicktest XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. Control Unit Name Control Unit Number Control Unit Short name Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 117, 156, 246 (MFA) 166, 176, 221, 242, 246, 292 Star 2 205, 213, 238, 253, 257, 290 (MRA) 117, 156, 246 (MFA) 118, 177, 243, 247 (MFA2) 167, 222, 292, 463, 465, 906 Star 3 294, 295, 296, 297 (EVA2) 206, 214, 223, 236, 254 (MRA2) 192 and 232 (MSA) 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": 205 213 222 238 253 257 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": 206 214 223 236 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 156 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" 118 177 243 247 EVA1.5 = "Electric Vehicle Architecture" 243 EVA2 = "Electric Vehicle Architecture - Generation 2" 294 295 296 297 MSA = "Mercedes-Benz Sport Architecture" 192 232 MMA = "Mercedes-Benz Modular Architecture" 174

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

Cause As part of the production process, the electrohydraulic controller units are subjected to a function test in an oil bath. Any oil residue remaining in the connector area can be regarded as production process-related. Since the oil used is a non-conducting, non-corrosive medium, the oil residue does not cause any technical impairment and does not result in any consequential damage. Remedy No action or replacement of parts is required! If necessary, clean the connector using compressed air only. Do not use any cleaning agents such as brake cleaner, as this could potentially cause consequential damage!

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).

The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Cause Coupling of the rear axle differential has reached the wear limit or a coupling issue is present. Remedy Please read off the part number of the rear axle differential installed on the vehicle and check the table below to determine if the differential can be repaired with a clutch repair kit. The table below is also in attachments. (If needed, check validity for further clarification of model designations). Complaint Instrument cluster message "4MATIC inoperative". The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Cause Coupling of the rear axle differential has reached the wear limit or a coupling issue is present. Remedy Please read off the part number of the rear axle differential installed on the vehicle and check the table below to determine if the differential can be repaired with a clutch repair kit. The table below is also in attachments. (If needed, check validity for further clarification of model designations)

and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Complaint Customer complaints regarding automatic transmission 724.1 (8FDCT & 8FDCT hybrid) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Complaint Customer complaints regarding automatic transmission 724.1 (8FDCT & 8FDCT hybrid) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process.

The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/ h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

The clunk is heard once when changing from forward to reverse (and vice versa). Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: Opening the camera cover for a maximum of 5 cumulative minutes. If the vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: Driving forward (typically less than 1 minute). Vehicle speed is < 35 km/h (<22 MPH). The steering wheel angle is < 10. During daylight. Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.

May be perceived as a noise from the transmission. Cause Controller instability of steering software, caused by reduced friction in steering (tolerance for production + running-in characteristics). Remedy Software A 247 902 11 16 available in Xentry with latest add-ons.

Individual or all tire pressure sensors are not recognized. Tire pressure monitoring system nonfunctional / temporarily unavailable. Cause Tires with excessively-large radio signal attenuation interfere with transmission of the tire pressure sensors. Remedy Check if one of the following tires is installed: If one of the tires listed above is installed with the corresponding DOT number, replace this tire. In accordance with the Warranty Manual, the costs for the tire shall be settled directly with the tire manufacturer.

Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

See Example Noise attachment Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy IMPORTANT: Do not apply document to vehicles outside of the listed validity range. The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. How to identify currently installed springs: Check for colored dots on the front springs. If no dots or color markings, please check if there is a parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please check for a barcode label with a 3 digit number. See "Spring Barcode" picture for example. Open a TIPS case with this number and list that it is from the barcode attached to the currently installed spring. If none of the above references can be found, open a TIPS case. How to identify next spring in line with color dots: Navigate to the parts catalog and enter the vehicle VIN/FIN. Navigate to group 32 sub-group 054 (front spring strut) and find the spring. The spring listed in the parts catalog will have a "color marking" indicator. If the dots on the spring and the color listed in the parts catalog is the same then you have the part number of the currently installed spring. If it does not, then you need to clear the vehicle specific filter by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). Proceed to finding the spring that matches the color dots on the vehicles currently installed spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".) How to identify next spring in line with part number tag: Navigate to the parts catalog and enter the vehicle VIN/FIN and the part number found from the spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. To do this, you need to clear the filters by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures).

See Example Noise attachment Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy IMPORTANT: Do not apply document to vehicles outside of the listed validity range. The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. How to identify currently installed springs: Check for colored dots on the front springs. If no dots or color markings, please check if there is a parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please check for a barcode label with a 3 digit number. See "Spring Barcode" picture for example. Open a TIPS case with this number and list that it is from the barcode attached to the currently installed spring. If none of the above references can be found, open a TIPS case. How to identify next spring in line with color dots: Navigate to the parts catalog and enter the vehicle VIN/FIN. Navigate to group 32 sub-group 054 (front spring strut) and find the spring. The spring listed in the parts catalog will have a "color marking" indicator. If the dots on the spring and the color listed in the parts catalog is the same then you have the part number of the currently installed spring. If it does not, then you need to clear the vehicle specific filter by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). Proceed to finding the spring that matches the color dots on the vehicles currently installed spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".) How to identify next spring in line with part number tag: Navigate to the parts catalog and enter the vehicle VIN/FIN and the part number found from the spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. To do this, you need to clear the filters by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".)

See "Sound Example" attachment. Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy IMPORTANT: Do not apply document to vehicles outside of the listed validity range. The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. How to identify currently installed springs: Check for colored dots on the front springs. If no dots or color markings, please check if there is a parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please check for a barcode label with a 3 digit number. See "Spring Barcode" picture for example. Open a TIPS case with this number and list that it is from the barcode attached to the currently installed spring. If none of the above references can be found, open a TIPS case. How to identify next spring in line with color dots: Navigate to the parts catalog and enter the vehicle VIN/FIN. Navigate to group 32 sub-group 054 (front spring strut) and find the spring. The spring listed in the parts catalog will have a "color marking" indicator. If the dots on the spring and the color listed in the parts catalog is the same then you have the part number of the currently installed spring. If it does not, then you need to clear the vehicle specific filter by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). Proceed to finding the spring that matches the color dots on the vehicles currently installed spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".) How to identify next spring in line with part number tag: Navigate to the parts catalog and enter the vehicle VIN/FIN and the part number found from the spring. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. To do this, you need to clear the filters by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".)

Cause A26/17 - MBUX multimedia system (head unit) software Remedy Update the A26/17 - MBUX multimedia system (head unit) to newest/latest software. Then recommission steering wheel electronics N135 - steering wheel electronics (LRE). If the problem is still present, please create a TIPS case. Note: Please do not replace any parts.

See Example Noise attachment Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. Verify currently installed spring in vehicle with use of color dots. NOTE: If no dots or color markings, please check the parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please open a TIPS case. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool.

See Example Noise attachment Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. Verify currently installed spring in vehicle with use of color dots. NOTE: If no dots or color markings, please check the parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. If the part label does not contain an MB part number, is missing or illegible, please open a TIPS case. In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number. IMPORTANT: Do not apply document to vehicles outside of the listed validity range.

Controller instability of steering software, caused by reduced friction in steering (tolerance for production + running-in characteristics). Software A 247 902 11 16 available in Xentry with latest add-ons.

with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams.

Remedy Grease/lubricate sealing area of input shaft. The steering components can be greased/lubricated while they are still installed

Possible when turning and also partly noticeable after changing to winter or all-season tires. Cause Controller stability of steering software, caused by reduced friction in steering (tolerance for production + running-in characteristics). Remedy Software update available in 1st quarter of 2023 (adaptation of stability limits)

Remedy Grease/lubricate sealing area of input shaft.

Remedy: Update software for steering wheel electronics control unit ("N 135 - Steering wheel electronics (LRE)"). Should the quick test carried out after the software update still show DTCs with the steering wheel heater and/or Distronic, replace the steering wheel control panels

Cause Insufficient sealing between the windshield lip seal and the body. Remedy Preliminary Check: Before beginning repairs, verify the source of the wind noise: 1. Mask off the joint between the windshield and the roof using tape. 2. Perform a test drive. 3. If the wind noise is no longer present, proceed with the repair steps below. 4. If the wind noise is still present, further diagnosis is required to locate the source of the noise. Repair Procedure: 1. Using tape, mask off the front edge of the roof along the entire length of the lip seal. (See Image1) 2. Apply window sealant between the lip seal and the body panel. (See Image 2) 3. Press the lip seal onto the front edge of the roof. 4. Clean the work area thoroughly and remove any excess sealant material. 5. Perform a road test to confirm the wind noise concern has been resolved.

(see attachment) Cause The cause is currently being investigated. Remedy Update the HU7 to the latest software version, then perform a factory reset of the HU7. Steps to perform factory reset: Navigate to Settings > System > Reset > Reset to factory settings and confirm If the problem persists, please record HU7 log and also a trace of the Body CAN (For Star 2 Body Can 1 and for Star 3 Body Can 2) during the symptom and send via a TIPS case to the Body/Chassis/Entertainment inbox. Note: Only collect and submit the log and trace if the symptom can be reliably reproduced.

TIREFIT sealant bottle may not meet specifications. The possibility exists that the sealant bottle may leak or may have otherwise been removed from the vehicle. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk.

(see attachment). Cause The cause is currently being investigated. Remedy Update the HU7 to the latest software version, then perform a factory reset of the HU7. Steps to perform factory reset: Navigate to Settings > System > Reset > Reset to factory settings and confirm. If the problem persists, please record HU7 log and also a trace of the Body CAN (For Star 2 Body Can 1 and for Star 3 Body Can 2) during the symptom and send via a TIPS case to the Telematics team. Note: Only collect and submit the log and trace if the symptom can be reliably reproduced.

Cause In rare cases, tension between the component parts of the LCP and trim of the center console could result in the buttons sticking. Remedy Remove LCP and reinstall while ensuring it is free of any tension. Replacement is not necessary.

Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: Perform SCN coding in control unit OMSH223 (N168). For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.

A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

Cause Sealing lip of inner sealing rail (see picture 1 and picture 2, pos. 40 and 130) folds down while side windows are being lowered (opened). When the side windows are raised (closed), the sealing lip is pulled back up again. Remedy Replace inner sealing rail. Then perform normalization of the window lifter system in the relevant door control unit.

Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead.

Remedy Replace B-pillar trim through optimized parts.

existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 9, 2026. After July 9th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.

The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Cause Coupling of the rear axle differential has reached the wear limit or a coupling defect is present. Remedy Please read off the installed part number of the rear axle differential. For model designations (flat model series and not AMG 35 variants) 118345; 118347; 118613; 118615; 118647; 177013; 177015; 177045; 177047; 177145; 177147; 177188; 177945; 247013; 247045; 247047, 247476 247747, 247646 247647 the following applies: If part number A2473502702 is not installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If part number A2473502702 is installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced. For model designations (high model series and AMG 35 variants) 177151; 177051; 118351; 118651; 177951, 247751 247753, 274651 the following applies: If one of the part numbers A2473502702; A2473502503; A2473504504 has not been installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part.

The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Coupling of the rear axle differential has reached the wear limit or a coupling defect is present. Remedy Please read off the installed part number of the rear axle differential. For model designations (flat model series and not AMG 35 variants) 118345; 118347; 118613; 118615; 118647; 177013; 177015; 177045; 177047; 177145; 177147; 177188; 177945; 247013; 247045; 247047, the following applies: If part number A2473502702 is not installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If part number A2473502702 is installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced. For model designations (high model series and AMG 35 variants) 177151; 177051; 118351; 118651; 177951, the following applies: If one of the part numbers A2473502702; A2473502503; A2473504504 has not been installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If one of the part numbers A2473502702; A2473502503; A2473504504 has been installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced.

CLS-Class, E-Class, GLA-Class, GLB-Class, GLC-Class, GLEClass, GLS-Class, and AMG GT (177, 118, 257, 213, 247, 253, 167 and 290 platform) vehicles without the augmented reality camera (ARC), as disclosed at the time of sale to the vehicle purchaser. As a result, the ARC and "Dash-cam" functions are currently not enabled. What Were Doing MBUSA will conduct a Service Campaign where an authorized Mercedes-Benz dealer will retrofit the ARC to the vehicle and enable the ARC and Dash-cam functions on applicable vehicles.

E-Class, GLA-Class, GLB-Class, GLE-Class, GLS-Class, and GT-Class (167, 177, 213, 247, 257, and 290 platform) vehicles without the augmented reality camera (ARC), as disclosed at the time of sale to the vehicle purchaser. As a result, the ARC and "Dash-cam" functions are currently not enabled. What Were Doing MBUSA will conduct a Service Campaign where an authorized Mercedes-Benz dealer will retrofit the augmented reality camera to the vehicle and enable the ARC and Dash-cam functions on applicable vehicles.

E-Class, GLA-Class, GLB-Class, GLE-Class, GLS-Class, and GT-Class (167, 177, 213, 247, 257, and 290 platform) vehicles without the augmented reality camera (ARC), as disclosed at the time of sale to the vehicle purchaser. As a result, the ARC and "Dash-cam" functions are currently not enabled. What Were Doing MBUSA will conduct a Service Campaign where an authorized Mercedes-Benz dealer will retrofit the augmented reality camera to the vehicle and enable the ARC and Dash-cam functions on applicable vehicles.

lights/intersections.

be that the welding spot for the "rear shelf crossmember/rear seat locking mechanism mount" at the left and right results in a noise complaint. Remedy Rework the welding points as described in the attachment using a high-strength rivet.

NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not preauthorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

function).</p><p>The result is a constant beep tone because no valid finger is detected and therefore no corresponding user profile can be assigned. </p> Cause <p>Software bug in A105 touchpad (TPAD).</p> Remedy <p>Perform software update in A105 touchpad (TPAD).</p>

Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.

Cause A setting on the iPhone may prevent control via the touchpad Remedy To remedy on the affected iPhone, navigate to "Settings" -> "Accessibility" -> "Touch" and turn the "BackTap" option OFF.

Cause Frictional vibrations between brake lining and brake disk. There is no impact to braking capabilities. Remedy Order and replace A0004202306 Linings of front axle as per parts catalog. It is not necessary to replace the brake disks; see also LI "Brake noises on AMG - vehicles" in design group 42.10.

mode and drive vehicle for approx 6mi. The DTC then switches to passive and the sensor can be calibrated

Cause Many possible root causes Remedy *Note - This Li does not apply if there are other Li's that apply to your concern OR you have a fault and/or guided test that leads to a root cause. AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements (Template attached to be used for submission of Warranty claim and/or TIPS case) Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour)

Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern Confirm the issue reported by the customer. Compare to Like Vehicle Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players Identify the diagnostic strategy and involved components/systems. Testing Perform relevant diagnostic tests. Refrigerant Quantity Record the amount of refrigerant recovered and compare it to the specified value (if applicable). Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements Cooling Capacity Test (If System Has a Charge) Before Repairs Gauge Readings High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) PPM of any leaks found. XENTRY Printouts Climate control AVs. HV compressor AVs (for heat and AC systems). Thermometer Readings Left and right dash vents. Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions Temperature and humidity from OCP AVs (if available). After Repairs - Warranty Submission Requirements on the Repair Order Gauge Readings High and Low pressure readings before and after repairs. Thermometer Readings Left and right dash vents before and after. Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation Complaint Analysis, Game/Players, and Testing Steps. Include expected results and technical justification for the diagnosis. Avoid listing R/I stepsfocus on diagnostic reasoning and root cause. All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found

to: Summer heat Direct sunlight Lack of air conditioning or ventilation Camera enters self-protection mode to prevent overheating. Remedy Do NOT replace any parts. The driver camera (NTG7: MDC295; CIVIC.i2: CIVIC206) is operating as designed. Allow the interior to cool down. If the message remains after cooling: Run XENTRY Diagnosis Check latest software for Actuation of Driver Camera (A26/17) No TIPS case required.

The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: Fluid intrusion Broken bushings or physical damage See attachments. Remedy If a component needs replacement but shows no visible external damage, submit a detailed TIPS case only when technical support is required. Include details of all connected external devices (such as charging cables, USB drives, and hard drives). If diagnostic results directly indicate component replacement, a TIPS case is not necessary.

Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: Fluid intrusion Broken bushings or physical damage See attachments. Remedy If a component needs replacement without visible external damage, submit a detailed TIPS case. Include information on all connected external devices (e.g., charging cables, USB drives, hard drives).

If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document. Conditions Instrument Cluster Message: "Park Assist Inoperative" and Hardware part numbers: A0009019716 or A0009016022 B223263 with Bosch-ID C259; A+S (Active and Stored) and B223255 with Bosch-ID 1B5D; A+S (Active and Stored) Notes: Other DTC's are permitted but the above three conditions must be met. If they are not met, this LI is not applicable. See attachment "LI Criteria" for an example. Attachment portrays a quick test with non-matching criteria and therefore does not require a TIPS case. Cause Under analysis. Remedy Please do not make any attempts to repair the park control unit. Do not flash or SCN code. Open a TIPS case.

If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document. Conditions Instrument Cluster Message: "Park Assist Inoperative" and Hardware part numbers: A0009019716 or A0009016022 B223263 with Bosch-ID C259; A+S (Active and Stored) and B223255 with Bosch-ID 1B5D; A+S (Active and Stored) Notes: Other DTC's are permitted but the above three conditions must be met. If they are not met, this LI is not applicable. See attachment "LI Criteria" for an example. Attachment portrays a quick test with non-matching criteria and therefore does not require a TIPS case. Cause Under analysis. Remedy Please do not make any attempts to repair the park control unit. Do not flash or SCN code. Open a TIPS case.

If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document. Conditions Instrument Cluster Message: "Park Assist Inoperative" and B223263 with Bosch-ID C259; A+S (Active and Stored) and B223255 with Bosch-ID 1B5D; A+S (Active and Stored) Notes: Other DTC's are permitted but the above three conditions must be met. If they are not met, this LI is not applicable. See attachment "LI Criteria" for an example. Attachment portrays a quick test with non-matching criteria and therefore does not require a TIPS case. Cause Under analysis. Remedy Please do not make any attempts to repair the park control unit. Do not flash or SCN code. Open a TIPS case.

If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document. Conditions Instrument Cluster Message: "Park Assist Inoperative" and B223263 with Bosch-ID C259; A+S (Active and Stored) and B223255 with Bosch-ID 1B5D; A+S (Active and Stored) Notes: Other DTC's are permitted but the above three conditions must be met. See Attachment for an example of Bosch ID location. Attachment portrays a quick test with non-matching criteria and therefore does not require a TIPS case. Cause Under analysis. Remedy Please do not make any attempts to repair the park control unit. Do not flash or SCN code. Open a TIPS case.

2020-2022 A-Class, C-Class, CLAClass, GLA-Class, GLB-Class, GLC-Class, GLE-Class, and GLS-Class (118, 167, 177, 205, 247, and 253 platform) vehicles, the mobile phone cradle control unit software does not correspond to the current series production specifications. It is therefore possible that the inductive charging function may not work as intended. What Were Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the mobile phone cradle control unit software.

Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.

periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!

A-Class, CLS-Class, E-Class, GLA-Class, GLB-Class, GLC-Class (118, 177, 213, 238, 247, 253, and 257 platform) vehicles were manufactured without the HERMES control unit, as disclosed to the vehicle purchaser at the time of sale. As a result, the Mercedes Me Connect services including the emergency call (eCall) function are currently not available. What Were Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will retrofit the HERMES control unit to the vehicle and enable the Mercedes Me Connect functions on applicable vehicles.