2016 Mazda MX-5 TSBs

Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with an active SAT radio.

The film of the center display may be peeled off. White dots may appear on the center display. Spider web-like cracking appearing in the corner(s) of the MAZDA CONNECT center display (the cracks are internal and cannot be felt by touch).

Peeling, spider cracks and white dots.

- The film of the center display may be peeled off. - White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.

- The film of the center display may be peeled off. - White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.

screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.

screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.

It includes new display repair kit part numbers for the 2018-2019 Mazda2, 2018-2020 CX-3 and 2018-2020 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White dots

There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Please use the table below when ordering the screen repair kits. This can also be found in Service Alert SA-041/22.

Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] * B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] * No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. * In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). * In other cases this DTC might be found without a related customer concern. NOTE: In most cases, no dealer visit is necessary.

- The film of the center display may be peeled off. - White dots may appear on the center display

Spider Cracks - Surface Peeling - White dots

Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

The cracks are internal and cannot be felt by touch. This concern may be caused by a lack of glue between the touch screen and the center display. To eliminate this concern in the future, the manufacturing process has been improved.

No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. 6 Bluetooth device will not pair No. 7 Incorrect GPS position No. 8 Voice Recognition Does Not Work No. 9 Cannot Make a Hands-Free Call No. 10 Cannot Play Bluetooth Audio No. 11 Other Symptoms No. 12 How to update the Navigation SD Card Map No. 13 How to Check Navi SD Card VIN Lock

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.230 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software. Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

This may be caused by an incorrect clock GPS Sync setting.

All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.

All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.

/ Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions

When the concern occurs, MAZDA CONNECT reboots repeatedly, and if the SD card is removed during this reboot cycle, the rebooting cycle ends. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error. To correct the concern, the SD card hardware has been changed.

Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles], B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles build on or before March 2, 2019], No DTC - Gen 7 vehicles built after March 2, 2019, DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

/ Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions

Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature.

This may be caused by an aftermarket accessory device.

Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. If swapped, the SD card that is installed into the other vehicle becomes linked to the VIN of that vehicle.

Navigation voice guidance will skip and cut out losing many words.Pandora will suddenly disconnect and MAZDA CONNECT will revert to the previously used source. If you encounter a vehicle with these issues, DO NOT attempt any repairs on the vehicle. There is nothing wrong with the vehicle. This is an issue with the Pandora APP. Have the customer contact Pandora at pandora-support@pandora.com. NOTE: If the Pandora APP works on the customer's phone, they can stream Pandora using Bluetooth.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.

CarPlay / Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS - Infotainment - MAZDA CONNECT Updates - Apple Carplay / Android Auto MDARS Activation Instructions

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update.

The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the SD card hardware has been changed.

The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the SD card hardware has been changed.

This may be caused by an incorrect clock GPS Sync setting.

of view B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.

Audio System, Bluetooth, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux Voice Command, How to Check Navi SD Card VIN Lock.

Use the troubleshooting chart below to repair the vehicle.

Use the troubleshooting chart below to repair the vehicle.

This may be caused by an incorrect clock GPS Sync setting.

B14F0:92 - General temporary failure in forward sensing camera (FSC). DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details. If the vehicle has this DTC, DO NOT replace the FSC. Read below.

NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software.Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

Use the flowchart below to repair the vehicle.

Many frequently asked question and the answers.

Use the flowchart below to repair the vehicle.

aha/Pandora/Stitcher/Bluetooth and the same device is also connected to the USB port for charging. The concerns may include: Blank Screen and/or No Audio Sound, Phone will not charge.Blank Screen and/or No Audio Sound These concerns may be caused by:The MAZDA CONNECT system has reached its capacity limits when streaming music with audio source aha/Pandora/Stitcher/Bluetooth and also connected to the USB port.The MAZDA CONNECT system has reached its capacity limits when the customer's USB device capacity exceeds 16 GB (e.g. 64 GB iPhone X). The MAZDA CONNECT system USB port capacity is 16 GB (FAT32).Mazda recommends not to connect any devices to the USB port when streaming music with audio source aha/Pandora/Stitcher/Bluetooth. When streaming music with audio source aha/Pandora/Stitcher/Bluetooth (without USB connection), the Connectivity Master Unit (CMU) is able to process Bluetooth digital data (A) and output audio sound and display Bluetooth audio information. If the same device is connected to the USB port for charging, the CMU processes both Bluetooth digital data (A) and USB digital data (B) from the same device at the same time. In this case, CMU resources may be exceeded, causing a Blank Screen and/or No Audio Sound.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement. NOTE: Always check for a TSB that may modify or eliminate prior authorization for a specific symptom for a given component.

for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active working SAT radio.

This is caused by a navigation map supplier software change. Customers can set preferences if needed. Example: A customer may have a Shell Gas Card and is only interested in Shell Gas Stations. The customer can set preference to only show Shell gas stations.

Use the flowchart below to repair the vehicle.

This is a normal condition. Album art and artist biographies are not provided by SiriusXM Satellite Radio, a blank white square frame is shown in place of the album art. Note: This information is also available at www.mazdahandsfree.com>FAQ>ENTERTAINMENT - SIRIUSXM. STATION LOGO SIRIUSXM satellite radio hardware is in the Tuner and Amp Unit (TAU). The station logo is not shown in the center display because there is no visual data communication cable between the TAU and the Connectivity Master Unit (CMU). A blank white square frame is shown in place of the station logo. Do NOT perform any repairs for these concerns.

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin.Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.100A or later). NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.

Use the flowchart below to repair the vehicle.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda's continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDACONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software. Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.

Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement. NOTE: Always check for a TSB that may modify or eliminate prior authorization for a specific symptom for a given component.

for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active (working SAT radio).

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.

The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during extremely cold temperatures. To correct the concern, the SD card hardware has been changed.

To resolve this concern, after the installation of the new CMU, check the software version.

aha/Pandora/Stitcher/Bluetooth and the same device is also connected to the USB port for charging. The concerns may include: Blank Screen and/or No Audio Sound, Phone will not charge, Blank Screen and/or No Audio Sound

The cracks are internal and cannot be felt by touch. This may be caused by a faulty center display.

This is a normal condition.

The cracks are internal and cannot be felt by touch. This concern may be caused by a lack of glue between the touch screen and the center display. To eliminate this concern in the future, the manufacturing process has been improved.

This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.

NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda's continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.

This may be caused by faulty navigation SD card software. TheSD card has been updated to eliminate this concern.

The concern occurs when the interior of the vehicle is cold and disappears when the interiorwarms up. This is caused by some for the MAZDA CONNECT navigation system SD cards beingmanufactured with improper hardware, resulting in a data reading error during cold temperatures. To correctthe concern, the SD card hardware has been changed.

This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping.The navigation SD card has a malfunction.

part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.

59.00.502or later).NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tabin MAZDA CONNECT Settingsbefore performing the update.

DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.

MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux, Voice Command

NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update.

part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502or later). NOTE: For CX-9 with version earlier than 59.00.441, the tachometer function has been removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software.

MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. This concern may be a normal operation of the CMU connecting to available devices on start up.

SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT.

TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750). EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750. NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT. SYSTEM DOES NOT RECOGNIZE USB/SD CARD. SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT. WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT. FAVORITES DISAPPEAR. VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH. REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN. TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE. WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCATION IS COMMA. CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE. NOTE: MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE,AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VERSION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

DIFFERENT SONG WILL PLAY.IF THE CUSTOMER SELECTS A DIFFERENT SONG, MOST OF THE TIME IT WILL CONTINUE PLAYING THE CURRENT SONG.IF THE CUSTOMER SHOULD SELECT THE CURRENT SONG AGAIN, IT MAY START PLAYING A DIFFERENT SONG.

TO IMPROVE THE HANDLING OF BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.CUSTOMERS EXPERIENCING RELATED CONCERNS SHOULD HAVE THEIR VEHICLE AND/OR DEVICE INSPECTED ACCORDING TO THE FOLLOWING PROCEDURE.

PART OF THE NEW CAR READY STEP 3 PROCESS. MAKE SURE THE NEW VEHICLE SPECIALIST RECEIVES A COPY OF THIS BULLETIN.SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 55.00.760 OR LATER).SOME STREET NAMES IN CANADA ARE NOT DISPLAYED.NAVIGATION DOES NOT ALLOW TO SET CERTAIN CITIES AS DESTINATION.NAVIGATION DOES NOT ANNOUNCE VOICE GUIDANCE FOR STREET NAMES.NAVIGATION TURNS TO A BLACK SCREEN REMAINING THE TASK BAR.TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750).EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750.NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT.SYSTEM DOES NOT RECOGNIZE USB/SD CARD.SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT.WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT.FAVORITES DISAPPEAR.VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH.REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN.TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE.WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCA-TION IS COMMA.CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE.NOTE:MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VER-SION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

56.00.760 OR LATER).SOME STREET NAMES IN CANADA ARE NOT DISPLAYED.NAVIGATION DOES NOT ALLOW TO SET CERTAIN CITIES AS DESTINATION.NAVIGATION DOES NOT ANNOUNCE VOICE GUIDANCE FOR STREET NAMES.NAVIGATION TURNS TO A BLACK SCREEN REMAINING THE TASK BAR.TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750).EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750.NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT.SYSTEM DOES NOT RECOGNIZE USB/SD CARD.SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT.WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT.FAVORITES DISAPPEAR.VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH.REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN.TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE.WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCA-TION IS COMMA.CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE.NOTE:MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VER-SION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

CONNECT.NAVIGATION VOICE GUIDANCE WILL SKIP AND CUT OUT LOSING MANY WORDS.PANDORA WILL SUDDENLY DISCONNECT AND MAZDA CONNECT WILL REVERT TO THE PREVIOUSLY USED SOURCE. IF YOU ENCOUNTER A VEHICLE WITH THESE ISSUES, DO NOT ATTEMPT ANY REPAIRS ON THE VEHICLE. THERE IS NOTHING WRONG WITH THE VEHICLE. THIS IS AN ISSUE WITH THE PANDORA APP. HAVE THE CUSTOMER CONTACT PANDORA AT PANDORA-SUPPORT@PANDORA.COM. NOTE: IF THE PANDORA APP WORKS ON THE CUSTOMER'S PHONE, THEY CAN STREAM PANDORA USING BLUETOOTH.

THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

PHONE CALLS WHEN THE SMARTPHONE IS PAIRED WITH A VEHICLE OR WIRELESS HEADSET. THE ISSUE EXTENDS TO GPS VOICE NAVIGATION FOR SOME, BUT STREAMING MUSIC OVER BLUETOOTH APPEARS TO BE UNAFFECTED. SPECIFICALLY, DOZENS OF USERS IN THE APPLE SUPPORT COMMUNITIES AND MACRUMORS DISCUSSION FORUMS CLAIM TO BE EXPERIENCING DISTORTED, STATICKY, OR INAUDIBLE PHONE CALLS WHEN USING AN IPHONE SE. IF YOU EXPERIENCE A CUSTOMER COMPLAINT, AND THE CUSTOMER HAS A NEW IPHONE SE, DO NOT REPLACE ANY PARTS ON THE VEHICLE. EXPLAIN TO THE CUSTOMER THAT THE IPHONE MAY BE THE PROBLEM. HAVE THE CUSTOMER VISIT THIS WEBSITE: HTTP://WWW.MACRUMORS.COM/2016/04/11/IPHONE-SE-BLUETOOTH-PHONE-CALL-AUDIO-ISSUES/

USE THIS VERSION FOR ALL MAZDA CONNECT UPDATES, INCLUDING OPEN SSP98 VEHICLES. IF SSP98 IS CLOSED, USE TSB 09-024/16 TO REPAIR THE VEHICLES.CLICK ON "IDS/INFOTAINMENT", THEN "MAZDA CONNECT UPDATES" TO DOWNLOAD IT. UPDATE YOUR USB DRIVES ACCORDING TO THE INSTRUCTIONS IN TSB 09-024/16.ALSO MAKE SURE TO SELECT "ALL FILES" FOR "SAVE AS TYPE:". IF LEFT AS "COMPRESSED (ZIPPED) FOLDER," THE FILE WILL BE SAVED AS A ".ZIP" NO MATTER WHAT YOU USE AS AN EXTENSION.ATTN: TECHNICIANS - BE SURE TO DOCUMENT THE SOFTWARE VERSION INSTALLED ON THE REPAIR ORDER AND INFORM YOUR WARRANTY ADMINISTRATOR TO PROVIDE THE INFORMATION IN THE REPAIR TEXT OF THE WARRANTY CLAIM.MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VERSION UPDATES CAN BE FOUND ON MS3.

55.00.760 OR LATER).SOME STREET NAMES IN CANADA ARE NOT DISPLAYED.NAVIGATION DOES NOT ALLOW TO SET CERTAIN CITIES AS DESTINATION.NAVIGATION DOES NOT ANNOUNCE VOICE GUIDANCE FOR STREET NAMES.NAVIGATION TURNS TO A BLACK SCREEN REMAINING THE TASK BAR.TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750).EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750.NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT.SYSTEM DOES NOT RECOGNIZE USB/SD CARD. SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT.WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT.FAVORITES DISAPPEAR.VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH.REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN.TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE.WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCA-TION IS COMMA.CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE.NOTE:MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VER-SION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

CONNECT.NAVIGATION VOICE GUIDANCE WILL SKIP AND CUT OUT LOSING MANY WORDS.PANDORA WILL SUDDENLY DISCONNECT AND MAZDA CONNECT WILL REVERT TO THE PREVIOUSLY USED SOURCE. IF YOU ENCOUNTER A VEHICLE WITH THESE ISSUES, DO NOT ATTEMPT ANY REPAIRS ON THE VEHICLE. THERE IS NOTHING WRONG WITH THE VEHICLE. THIS IS AN ISSUE WITH THE PANDORA APP. HAVE THE CUSTOMER CONTACT PANDORA AT PANDORA-SUPPORT@PANDORA.COM. NOTE: IF THE PANDORA APP WORKS ON THE CUSTOMER'S PHONE, THEY CAN STREAM PANDORA USING BLUETOOTH.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button

The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.

The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.

The changes are noted in Red. 01-008/23 06/05/23 Some vehicles may exhibit rattling noises from the engine compartment and oil leakage from the drive belt auto tensioner. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed. REPAIR PROCEDURE If the tensioner is found to be "No Good" after completing the Drive Belt Auto Tensioner Inspection, replace it with a modified part according to the instructions on MGSS online:

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). Only Mazda-approved key cutting machines can process these 10-digit codes. Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.

and/or making an abnormal noise while operating the power window switch. This may be caused by the cable of the power window motor being damaged from water entry through area (1) of the front beltline molding. Convertible Top: To eliminate this concern, the shape of the door glass has been modified during mass production to prevent water entry to the power window regulator. Retractable Hardtop: No mass production change is scheduled.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service. Examples of residue or seepage that may not be considered a leak and that may not require repair based on splash shield inspection.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

whine, groan, rattle or squeak) coming from the front combination lights when turning them on, or a few minutes after turning them off. The noise may be due to contamination by foreign matter during the manufacturing process and the fan motor bearing may become worn out during use. To eliminate this concern, the fan motor has been modified. NOTE: It is normal for some noise to occur within the first few seconds after starting the engine, when the front combination lights perform a self check (sweep).

Foreign debris on the blower motor after servicing the cabin air filter may be the cause. During the removal of the cabin air filter, foreign debris (leaves, dust, dirt....ect.) may fall on the blower motor causing a fluttering type noise or odor.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.

Vehicles having this concern should use the following Inspection/Repair procedure.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location)

This is caused when the vehicle decelerates, its weight, together with the pulses from the engine, excites the backlash in the transmission gears, causing them to buzz or rattle. Clearance between transmission gears (backlash) is normal and sometimes can become audible.

This is caused by a crack in the cooler pipe (HI) A (1) due to engine vibration. To correct this issue, the material and thickness of the cooler pipe (HI) A has been changed to increase durability (pipe diameter has been changed from 12mm to 16mm).

Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline, E85: A blend of 85% ethanol and 15% gasoline, All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V. What if a customer puts E85 in there Mazda vehicle? Symptoms include: Rough Running, Lean Codes, Misfires and/or misfire codes, Lack of power, Poor fuel economy, Spark knock, Mechanical engine damage.

This may be caused by a customer installed aftermarket decorative trim and/or cover on the START/STOP ENGINE button. The aftermarket accessory may create electrical interference, which may interfere with programming.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

This is caused by a crack in the cooler pipe (HI) A (1) due to engine vibration. To correct this issue, the material and thickness of the cooler pipe (HI) A has been changed to increase durability (pipe diameter has been changed from 12mm to 16mm).

P2610:00: Instrument cluster internal engine off timer performance problem. P2507:00: PCM battery voltage low input

and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery voltage low input.

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? Yes - No repair is necessary. No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE).

head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display F0-002 during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km).Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear Parking Sensors - Rear Seat Entertainment - Smartphone Screen Mirroring - Bumper Trim/Guards - Door Mirror Caps - Fog Lights - Moonroof Wind Deflector - Roof Rack - Side Window Deflectors - Splash Guards - Trailer Hitch - Thule Products - Wheels Locks - Aero Kit - Air Dam - Rear Spoiler - Tunnel Under Bars - Lower Arm Bar - Side Sill Extensions - Arm Rest - Illuminated Door sill Trim Plates - Interior Lighting

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.

Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.

Engine Start/Start Button Amber indicator light flashing Battery discharge Electrical relay buzzing noise DTC B13D3:94 (Communication error with remote transmitter) stored.This may be caused by: A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehicless wiring harness may create unusual electrical symptoms.

This may be caused by a plugged heater core. For 2014-2016 Mazda6 and 2013-2016 (US spec) / 2017 (Mexico spec) CX-5, the CHECK ENGINE light may turn on with DTC P011A:00 (ECT sensor No.1/No.2 performance problem) stored at the same time. NOTE: Refer to TSB 01-015/15 if the customer is using a block heater at temperatures below freezing. To solve this concern, two mass production changes have been implemented. a) The concentration of the coolant has been increased so that the amount of the contained anti-rust additive is higher. b) The composition of the coolant has been changed (the ratio of the anti-rust additive has increased).

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial checkis a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.

Unlike previous Mazda models, there is no key cylinder on the steering column. Therefore, the engine cannot be started with the auxiliary key if the room fuse is removed or if the transmitter battery is dead.

The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. This can happen if the ignition is turned OFF within 20 seconds after the ignition is turned ON in one of the following two situations. 1. The ?ROOM? fuse (Engine compartment) is NOT installed when battery level is low. 2. The CMU (Connectivity Master Unit) is NOT connected.

refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.

and/or making an abnormal noise while operating the power window switch. This may be caused by the cable of the power window motor being damaged from water entry through area (1) of the front beltline molding.To eliminate this concern, the shape of the door glass will be modified during mass production to prevent water entry to the power window regulator.

deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. This can happen if the ignition is turned OFF within 20 seconds after the ignition is turned ON in one of the following two situations. 1. The ?ROOM? fuse (Engine compartment) is NOT installed when battery level is low. 2. The CMU (Connectivity Master Unit) is NOT connected.

refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system. When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur to oxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise.This may be caused by: A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehicles?s wiring harness may create unusual electrical symptoms.

A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger, GPS tracker...) may create excessive electrical noise. The noise may interrupt some of the vehicle electrical systems. Below are a few examples of an aftermarket cell phone charger and GPS tracker that are interrupting the vehicle electrical systems.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

This is caused by a crack in the cooler pipe (HI) A (1) due to engine vibration. To correct this issue, the material and thickness of the cooler pipe (HI) A has been changed to increase durability. (1) Cooler pipe (HI) A (2) A/C compressor (3) Condenser Location of cracking.

Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing.

complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger) may create excessive electrical noise. The noise may interrupt some of the vehicle electrical systems. Below are a few examples of an aftermarket cell phone charger that is interrupting the vehicle electrical systems.

(e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

temperature), the engine oil may become diluted with fuel and the engine oil level will increase. Engine oil dilution with fuel occurring under this specific driving condition is normal with direct injection engines. If the vehicle is driven on a longer trip after a lot of short trips (where the engine reaches normal operating temperature), the Check Engine Light may turn ON with DTC P0172:00 (Fuel system too rich).

This is caused by a crack in the cooler pipe (HI) A (1) due to engine vibration. To correct this issue, the material and thickness of the cooler pipe (HI) A has been changed to increase durability.

This is caused by a crack in the cooler pipe (HI) A (1) due to engine vibration. To correct this issue, the material and thickness of the cooler pipe (HI) A has been changed to increase durability.

P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/Cevaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers. This treatment provides a durable coating that will aid to prevent biological reactions that lead to odorconcerns. It is applied to the evaporator in a misted form that is introduced by way of the cabin air filter, the re-circulate door, the blower motor resistor access, or the blower motor air intake. Proper application requires the evaporator surface to be: Relatively clean and free of leaves, dust build-up and debris. Thoroughly dried, and the product cured onto it after application. NOTE: Keep the cooling unit dry by leaving the blower fan ON (at least on low), even if the A/C is not being used. In low humidity (dry) conditions, keep the ventilation system in the "FRESH" mode all the time, or as much as possible. In high humidity conditions, or if the air has a lot of dust or pollen, keep the system in the "RECIRCULATION" mode. A few minutes before reaching a destination, turn the A/C OFF, but leave the blower fan ON. This stops the accumulation of condensation on the evaporator/cooling unit, and it helps dry the inside of the cooling unit. A/C odor is not unique to Mazda vehicles as it will occur in other makes and models. To minimize A/C odor, suggest the following to the customers.

This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial check is a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.

Unlike previous Mazdamodels, there is no key cylinder on the steering column. Therefore, the engine cannot be started with theauxiliary key if the room fuse is removed or if the transmitter battery is dead.NOTE: The auxiliary key can only be used to lock or unlock the doors. It cannot be used to start the engine. Two transmitters are placed in a vinyl bag and stored in the center console cup holder. Since the room fuse is not installed during vehicle assembly, a new procedure is required to start the engine. Refer to "Engine Start Procedure" below.

The unique oil filter can be identified with two white bands as shown below.

doors will not lock/unlock when using a request switch. The engine will start if you touch the backside of the remote (1) to the push button start (2). This may be caused by water running down between the windshield and the dashboard resulting in corrosion of the terminals at connectors C-16 and/or C-04. To correct this issue, shield plates have been attached to the upper dashboard to prevent water from dropping onto these connectors.

Vehicles having this concern should use the following Inspection/Repair procedure.

? A grinding noise occurs when the transmission is shifted from 1st to 2nd and/or from 2nd to 3rd gear or in the neutral position with the engine idling. ? It is impossible to shift into 2nd and/or 3rd gear while there is no problem shifting into other gears. This may be caused by damage to 2nd and/or 3rd gears if the vehicle was driven with rapid acceleration and deceleration using frequent shift changes. To eliminate this concern, the configuration of the 2nd and 3rd gears has been changed to increase the rigidity. NOTE: Transmissions with the serial No. ?6TJ0701679? or higher are modified.

A grinding noise occurs when the transmission is shifted from 1st to 2nd and/or from 2nd to 3rd gear or in the neutral position with the engine idling. It is impossible to shift into 2nd and/or 3rd gear while there is no problem shifting into other gears. This may be caused by damage to 2nd and/or 3rd gears if the vehicle was driven with rapid acceleration and deceleration using frequent shift changes. To eliminate this concern, the configuration of the 2nd and 3rd gears has been changed to increase the rigidity. NOTE: Transmissions with the serial No. ?6TJ0701679? or higher are modified.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the ?SpeedometerReplacement Label?.Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda?s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.With the use of SPECMO?s services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

A grinding noise occurs when the transmission is shifted from 1st to 2nd and/or from 2nd to 3rd gear or in the neutral position with the engine idling. It is impossible to shift into 2nd and/or 3rd gear while there is no problem shifting into other gears. This may be caused by damage to 2nd and/or 3rd gears if the vehicle was driven with rapid acceleration and deceleration using frequent shift changes. To eliminate this concern, the configuration of the 2nd and 3rd gears has been changed to increase the rigidity.

PIPE (HIGH PRESSURE SIDE) AT THE EXPANSION VALVE.

P2610:00: INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM P2507:00: PCM BATTERY VOLTAGE LOW INPUT AS A PAST MALFUNCTION, THE CUSTOMER WILL NOT NOTICE IT (NO WARNING LIGHT ILLUMINATED), BUT THE DTC MAY BE FOUND DURING A VEHICLE SERVICE. P2507 IN THIS SITUATION IS ONLY APPLICABLE ON 2016 AND LATER MODELS. THIS IS CAUSED BY THE ENGINE BEING STARTED 3 OR MORE TIMES AFTER A SHORT DURATION OF ENGINE OFF (LESS THAN 15 SECONDS) WITH THE ROOM FUSED REMOVED.

PIPE (HIGH PRESSURE SIDE) AT THE EXPANSION VALVE.

THE PURPOSE OF A PERMANENT DTC IS TO PREVENT CUSTOMERS FROM CLEARING THEM BY DISCONNECTING THE BATTERY CABLE IN ORDER TO PASS A SMOG CHECK. ALL PCM AND TCM DTCS THAT TURN ON THE CHECK ENGINE LIGHT CAN REMAIN AS A PERMANENT DTC. THEY WILL NOT TURN ON THE CHECK ENGINE LIGHT OR CAUSE DRIVABILITY CONCERNS. IF YOU ENCOUNTER A PERMANENT DTC, IGNORE IT AND DIAGNOSE THE CURRENT STORED OR PENDING DTC.

BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT.

THIS SERVICE BULLETIN IS TO INFORM YOU ABOUT THE WATER PUMP SEALING MECHA-NISM AND THE CRITERIA IF REPLACEMENT IS NECESSARY OR NOT.

THE UNIQUE OIL FILTER CAN BE IDENTIFIED WITH TWO WHITE BANDS AS SHOWN BELOW.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738).P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONP0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.NOTE:IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738).P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONP0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.NOTE:IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.

BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT

the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. In most cases, if the left-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" can be completed without any problem (See CAUTION below for more details). Other possible symptoms that may be found if the right-side BSM module is replaced alone: BSM aiming fails BSM OFF" indicator ON Center Display warning message BSM failsafe (No operation) DTC U3000:54 stored in memory DTC U1A4B:54 stored in memory (CX-3, MX-5 only) NOTE: Since a new BSM control module does not retain the vehicle specification information, it is necessary to acquire and store the vehicle specification information transmitted via CAN communication from the combination meter through automatic configuration after replacement.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.

lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.

lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced since December 2021 at the supplier.

This is caused by a failure in the ambient temperature sensor. To correct this issue, the ambient temperature sensor has been modified.

the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. Other possible symptoms that may be found if the right-side BSM module is replaced alone: * BSM aiming fails * "BSM OFF" indicator ON * Center Display warning message * BSM failsafe (No operation) * DTC U3000:54 stored in memory * DTC U1A4B:54 stored in memory (CX-3, MX-5 only)

activated, even though there is no occupant in the front passenger seat. When a passenger seat occupant sits with a load on the front side for a long time with the seat warmer on, the occupancy sensor becomes dented and sensitive. As a result, the sensor determines that there is an occupant in the front passenger seat even though the seat is empty.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

(SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.

maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a good know terminal.To measure the voltage/resistance avoiding any terminal damage.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc.) placed on the front passenger's seat.

data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage.

Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area. Adjacent vehicle (B) driving at same speed, even if the vehicle is still in the alert area. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address these customer concerns.

The symptoms may include: When the ignition is switched ON, the warning indicator light turns ON momentarily and then turns off after a few seconds. The BSM system does not operate after 1st key cycle (cold soak), No DTCs stored in memory, BSM system will function normally after 2nd key cycle and the vehicle is driven on the street

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all auxiliary keys are lost.

Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.

data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.

the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. Other possible symptoms that may be found if the right-side BSM module is replaced alone: BSM aiming fails, BSM OFF" indicator ON, Center Display warning message, BSM failsafe (No operation), DTC U3000:54 stored in memory, DTC U1A4B:54 stored in memory (CX-3, MX-5 only).

notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.

If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps):CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery's Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda GR8-1291, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The(BSM) radar aiming is performed whenever the (BSM) control module, the (BSM) bracket or the rear bumper is replaced. The tool is available for loan by contacting DAG.

notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed. This TSB is applicable for the following cases. The oil change due notification does not come on, even after mileage exceeded 10,000 miles. Oil life in the center display is still less than 40% even though the mileage exceeded 7,000 miles. To display "Flexible" setting and "Oil life" on the center screen, select the "Applications" screen, "Maintenance", then "Oil Change" tab. For complete details, refer to the the instructions on MGSS (MAINTENANCE MONITOR OPERATION PROCEDURE).

OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc.) placed on the front passenger's seat.

initialization was not performed correctly before customer delivery.TPMS INITIALIZATION PROCESS: When any of the services below is performed, BE SURE TO INITIALIZE THE TPMS BEFORE DRIVING THE VEHICLE by pushing and holding the TPMS Set Switch on the dash until the TPMS warning light flashes two times and the warning beep sounds once. The TPMS must be initialized in the following cases: 1. Tire pressures have been adjusted in one or more tires. 2. Tires have been rotated. 3. Tires or wheels have been replaced. 4. The vehicle's battery cable has been disconnected for any reason. 5. The vehicle's battery has been discharged. 6. The DSC HU/CM connector has been disconnected for any reason.

Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

Vehicle odometer under 62 miles ? VIN-lock occurs with key ON for 3 minutes or longer. 2. Vehicle odometer over 62 miles ? VIN-lock occurs at key ON. Navigation SD Card Map Update Note: Mazda Toolbox navigation SD card map update can only be performed on a navigation SD card that is VIN-locked. See VIN-lock procecure below.

Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The (BSM) radar aiming is performed whenever the (BSM) control module, the (BSM) bracket or the rear bumper is replaced. The tool is available for loan on Mazda e-Store.

vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area.? Adjacent vehicle (B) driving at same speed, even if the vehicle is still in the alert area. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address these customer concerns.

indicator light on the outer mirror glass does not illuminate. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address this customer concern.

modules detect dirt on the rear bumper surface): DTC U1A4B:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (RH)), DTC U3000:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (LH)), The BSM turns ?OFF? and the BSM OFF indicator turns ?ON? in the instrument cluster while driving, The BSM will not turn on again during the drive cycle, After cycling the ignition switch off and on again, the BSM operates normally, DTC U1A4B:97 or U3000:97 is stored in memory. To correct this problem, the control logic of the BSM control modules has been changed.

if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No. 2 (C) socket covers have not been correctly installed or are missing due to improper prior repairs (i.e., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, HID module seal (D), or missing bumper brackets (E) is not covered by warranty policy.

indicator light on the outer mirror glass does not illuminate. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address this customer concern.

When you encounter a customer with this concern, first verify the condition when the customer noticed this symptom. If the condition is similar to the following "CONTROL LOGIC OF AMBIENT TEMPERATURE" or "DIFFERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS", advise the customer that this is a normal characteristic of the vehicle and not a malfunction. If the condition does not meet the following and the sensor malfunction is suspected, make sure to inspect the sensor according to MGSSonline or Workshop Manual (section 09-22 AMBIENT TEMPERATURE SENSOR INSPECTION). Replace the sensor only when it fails the Workshop Manual inspection.

prevent the battery from discharging.

Operations is 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

modules detect dirt on the rear bumper surface):

IF ALL THE BULB SOCKETS ARE RESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET OVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.

THE TEST KIT IS DESIGNED PECIFICALLY FOR SKYACTIV MODULE TERMINALS. THE SST WILL BE SHIPPED BY MAZDAS TOOL VENDOR BOSCH STARTING JANUARY 15, 2016. PROCEDURES FOR USAGE ARE FOUND IN THE SKYACTIV WIRING TERMINAL TEST KIT WBT, COURSE #1649. THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST:

MODULES DETECT DIRT ON THE REAR BUMPER SURFACE): THE BSM TURNS OFF AND THE BSM OFF INDICATOR TURNS ON IN THE INSTRUMENT CLUSTER WHILE DRIVING THE BSM WILL NOT TURN ON AGAIN DURING THE DRIVE CYCLE AFTER CYCLING THE IGNITION SWITCH OFF AND ON AGAIN, THE BSM OPERATES NORMALLY DTC U1A4B:97 OR U3000:97 IS STORED IN MEMORY - DTC U1A4B:97 - RADAR SENSOR SENSITIVITY TEMPORARILY DECREASES DEPENDING ON VARIOUS EXTERNAL AND ENVIRONMENTAL FACTORS (BLIND SPOT MONITORING (BSM) CONTROL MODULE (RH)) - DTC U3000:97 - RADAR SENSOR SENSITIVITY TEMPORARILY DECREASES DEPENDING ON VARIOUS EXTERNAL AND ENVIRONMENTAL FACTORS (BLIND SPOT MONITORING (BSM) CONTROL MODULE (LH)) TO CORRECT THIS PROBLEM, THE CONTROL LOGIC OF THE BSM CONTROL MODULES HAS BEEN CHANGED.

TO COMPLETE THE RADAR AIMING PROCEDURE (IT IS OK TO REPLACE THE LEFT BSM ALONE). REASON IF THE RIGHT-SIDE BSM CONTROL MODULE IS REPLACED ALONE, AUTOMATIC CONFIGURATION IS NOT PERFORMED DUE TO A PROGRAM ERROR IN THE MODULE. BECAUSE OF THIS, THE REQUIRED BSM RADAR AIMING CANNOT BE PERFORMED. AUTOMATIC CONFIGURATION AS WELL AS BSM RADAR AIMING CAN BE PERFORMED, IF THE LEFT-SIDE BSM CONTROL MODULE IS REPLACED ALONE OR TOGETHER WITH THE RIGHT-SIDE BSM CONTROL MODULE.

TOOL (SST) TO ALLOW FOR THE RADAR AIMING OF THE BLIND SPOT MONITORING (BSM) SYSTEM. THE (BSM) RADAR AIMING IS PERFORMED WHENEVER THE (BSM) CONTROL MODULE, THE (BSM) BRACKET OR THE REAR BUMPER IS REPLACED. THE TOOL IS AVAILABLE FOR LOAN ON MAZDA E-STORE.

TO COMPLETE THE RADAR AIMING PROCEDURE (IT IS OK TO REPLACE THE LEFT BSM ALONE). REASON IF THE RIGHT-SIDE BSM CONTROL MODULE IS REPLACED ALONE, AUTOMATIC CONFIGURATION IS NOT PERFORMED DUE TO A PROGRAM ERROR IN THE MODULE. BECAUSE OF THIS, THE REQUIRED BSM RADAR AIMING CANNOT BE PERFORMED. AUTOMATIC CONFIGURATION AS WELL AS BSM RADAR AIMING CAN BE PERFORMED, IF THE LEFT-SIDE BSM CONTROL MODULE IS REPLACED ALONE OR TOGETHER WITH THE RIGHT-SIDE BSM CONTROL MODULE.

(2) DOOR LOCKS REPEATEDLY LOCK AND UNLOCK WHEN APPROACHING THE VEHICLE WITH THE ADVANCED KEY. (3) KEY WARNING LIGHT (RED) ON WHILE DRIVING AND DTC B10D1:23 AND/OR B10D3:23 IS(ARE) STORED. B10D1:23 REQUEST SWITCH (LF) CIRCUIT MALFUNCTION B10D3:23 REQUEST SWITCH (RF) CIRCUIT MALFUNCTION

TOOL (SST) TO ALLOW FOR THE RADAR AIMING OF THE BLIND SPOT MONITORING (BSM) SYSTEM. THE (BSM) RADAR AIMING IS PERFORMED WHENEVER THE (BSM) CONTROL MODULE, THE (BSM) BRACKET OR THE REAR BUMPER IS REPLACED. THE TOOL IS AVAILABLE FOR LOAN ON MAZDA E-STORE.

IF NOT USED, THE CONTROL MODULE REPROGRAMMING MAY FAIL DUE TO A WEAK VEHICLE BATTERY.THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE PREVENTS THE VEHICLE BATTERY FROM BEING DISCHARGED. THIS ALLOWS THE IDS TO REPROGRAM A CONTROL MODULE WITHOUT INTERFERENCE FROM A WEAK OR UNDERCHARGED VEHICLE BATTERY. NOTE: CONTROL MODULE DAMAGE MAY OCCUR IF THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE IS NOT USED.

THIS MAY BE CAUSED BY AN OBSTRUCTION OF THE FRONT AND/OR REAR LIGHT SENSOR(S) (E.G. HANGING A PARKING PERMIT FROM THE MIRROR). USE A SOFT CLOTH WITH MILD DETERGENT TO CLEAN THE MIRROR. HARSH DETERGENT MAY DAMAGE THE FRONT AND/OR REAR LIGHT SENSOR(S).

IF AN AFTERMARKET ALARM SYSTEM IS INSTALLED, THE REAR HARNESS MIGHT HAVE RECEIVED DAMAGE FROM ELECTRO-TAP CONNECTORS (A) OR TO THE PROTECTOR TUBE (B). THIS DAMAGE IS NOT COVERED UNDER WARRANTY.

UNPLUG THE MODULE FOR AT LEAST 10 SECONDS.RECONNECT THE BATTERY, WAIT 60 SECONDS AND THEN HAVE THE CUSTOMER TRY THE APP AGAIN.IF THE VEHICLE STARTS, ORDER MODULE 0000-8F-Z80A.NOTE: THERE IS A LIMITED SUPPLY OF THE MODULE AT THIS TIME, THEREFORE ONLY USE THIS PART FOR THIS SPECIFIC CONDITION.DUE TO THE LIMITED SUPPLY, MAKE SURE YOU WERE SHIPPED THE A LEVEL PART AND NOT THE ORIGINAL PART BEFORE INSTALLING THE PART.INSTALL THE MODULE AND PROGRAM IT PER MMS PROGRAMMING INSTRUCTIONS.INSTRUCT THE CUSTOMER TO UPDATE THEIR ACCOUNT WITH THE NEW MODULE INFORMATION, OTHERWISE THE MMS WILL NOT WORK FROM THE APP.

SOME VEHICLES WITH BLIND SPOT MONITORING (BSM) MAY EXPERIENCE THE FOLLOWING CONDITIONS (SIMILAR TO WHEN THE BSM CONTROL MODULES DETECT DIRT ON REAR BUMPERS SURFACE): BSM TURNS "OFF" AND BSM OFF INDICATOR TURNS "ON" IN THE INSTRUMENT CLUSTER WHILE DRIVING; BSM WILL NOT TURN ON AGAIN DURING DRIVE CYCLE; AFTER CYCLING, IGNITION SWITCH OFF AND ON AGAIN, BSM OPERATES NORMALLY; DTC U1A4B:97 OR U3000:97 IS STORED IN MEMORY.

IF RIGHT-DIDE BSM CONTROL MODULE REQURES REPLACEMENT FOR ANY REPAIR, ALSO REPLACE LEFT SIDE BSM CONTROL MODULE TO COMPELTE THE RADAR AIMING PROCEDURE (IT'S OK TO REPLACE THE LEFT BSM ALONE). IF THE RIGHT-SIDE BSM CONTROL MODULE IS REPLACED ALONE, "AUTOMATIC CONFIGURATION" IS NOT PERFORMED DUE TO PROGRAM ERROR IN MODULE. BECAUSE OF THIS, THE REQUIRED "BSM RADAR AIMING" CANNOT BE PERFORMED. "AUTOMATIC CONFIGURATION" AS WELL AS "BSM RADAR AIMING" CAN BE PERFORMED IF LEFT-SIDE BSM CONTROL MODULE IS REPLACED ALONE OR TOGETHER WITH RIGHT-SIDE BSM CONTROL MODULE.

SOME VEHICLES MAY EXHIBIT BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THEHANDLING OF BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CREATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010. CUSTOMERS EXPERIENCING RELATED CONCERNS SHOULD HAVE THEIR VEHICLE AND/OR DEVICE INSPECTED ACCORDING TO THE FOLLOWING PROCEDURE.

Due to assembly variations, the clearance between the seat back bar garnish and the convertible top is too small on some vehicles. REPAIR PROCEDURE 6. Install the seat back crossmember assembly from the vehicle according to the instructions on MGSS online or the Workshop Manual (section 09-10 SEAT BACK CROSSMEMBER ASSEMBLY REMOVAL/INSTALLATION). 7. Reinstall the rear seat back bar garnish while twisting the garnish so that the garnish can be kept closer to the seat back bar and away from the convertible top (for both left and right sides).

There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

Due to assembly variations, the clearance between the seat back bar garnish and the convertible top is too small on some vehicles.

The molding material on the retractable hardtop quarter garnish may accelerate the deterioration of the quarter garnish, resulting in the cracks. To eliminate this concern, the molding material on the retractable hardtop quarter garnish has been improved.

top (3).

Due to assembly variations, the clearance between the seat back bar garnish and the convertible top is too small on some vehicles.

A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section once a part is selected. Accessories E-catalog For models prior to 2016: Accessory Parts and Installation Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method A. Auxiliary Key Trace Cut Method If only one auxiliary key is lost/missing, some key cutting machines can trace cut a new key blank. 1. Trace cut the new auxiliary key blank(s). B. Auxiliary Key Code Cut Method If both auxiliary keys are lost/missing, use this method for cutting new auxiliary key blank(s). 1. Confirm you have access to a Mazda approved key cutting machine. See Mazda Approved Key Cutting Machine table.

A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

Due to assembly variations, the clearance between the seat back bar garnish and the convertible top is too small on some vehicles.

Due to assembly variations, the clearance between the seat back bar garnish and the convertible top is too small on some vehicles.

seat back surface.Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.

https://ecatalog.mazdausa.com

top (3).Due to assembly variations, the clearance between the seat back bar garnish and the convertible top is too small on some vehicles.On later 2016 models (starting with VINs JM1ND******117681), the link stopper of the convertible top has been changed to adjust the opening angle and folding position of the convertible top. This increased the gap between the seat back bar garnish and the convertible top when folded down. On these later models, the issue seems to occur if the customer does not completely lock the convertible top down when lowered. NOTE: Make the customer aware that the top needs to be completely locked down when lowered to prevent this from happening. With the convertible top lowered, press down on both the front and rear areas of the top (as shown with the arrows) until a latch sound is heard and the top does not pop up.

for download.

https://ecatalog.trademotion.com/

Due to assembly variations, the clearance between the seat back bar garnish and the convertible top is too small on some vehicles.On later 2016 models (starting with VINs JM1ND******117681), the link stopper of the convertible top has been changed to adjust the opening angle and folding position of the convertible top. This increased the gap between the seat back bar garnish and the convertible top when folded down. On these later models, the issue seems to occur if the customer does not completely lock the convertible top down when lowered. NOTE: Make the customer aware that the top needs to be completely locked down when lowered to prevent this from happening. With the convertible top lowered, press down on both the front and rear areas of the top (as shown with the arrows) until a latch sound is heard and the top does not pop up.

license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the resetting tool.

Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.

DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.

Due to assembly variations, the clearance between the seat back bar garnish and the convertible top is too small on some vehicles. On later 2016 models (starting with VINs JM1ND******117681), the link stopper of the convertible top has been changed to adjust the opening angle and folding position of the convertible top. This increased the gap between the seat back bar garnish and the convertible top when folded down. On these later models, the issue seems to occur if the customer does not completely lock the convertible top down when lowered. NOTE: Make the customer aware that the top needs to be completely locked down when lowered to prevent this from happening. With the convertible top lowered, press down on both the front and rear areas of the top (as shown with the arrows) until a latch sound is heard and the top does not pop up.

CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the resetting tool.

seat back surface.

WHEN WIPING IT WITH CLOTH OR REMOVING THE PROTECTIVE COVER ON IT. THE RETAINING FORCE OF THE SCUFF PLATE CLIPS (B) MAY BE INSUFFICIENT. TO CORRECT THE PROBLEM, THE SHAPE OF THE SCUFF PLATE CLIPS HAS BEEN CHANGED TO INCREASE THE RETAINING FORCE.

DUE TO ASSEMBLY VARIATIONS, THE CLEARANCE BETWEEN THE SEAT BACK BAR GARNISH AND THE CONVERTIBLE TOP IS TOO SMALL ON SOME VEHICLES.

TOP (C).DUE TO ASSEMBLY VARIATIONS, THE CLEARANCE BETWEEN THE SEAT BACK BAR GARNISH AND THE CONVERTIBLE TOP IS TOO SMALL ON SOME VEHICLES.

DUE TO ASSEMBLY VARIATIONS, THE CLEARANCE BETWEEN THE SEAT BACK BAR GARNISH AND THE CONVERTIBLE TOP IS TOO SMALL ON SOME VEHICLES.TO CORRECT THE CONCERN, THE LINK STOPPER OF CONVERTIBLE TOP HAS BEEN CHANGED TO ADJUST THE OPENING ANGLE AND FOLDING POSITION OF THE CONVERTIBLE TOP. THIS WILL INCREASE THE GAP BETWEEN THE SEAT BACK BAR GARNISH AND THE CON-VERTIBLE TOP WHEN FOLDED DOWN.

DTC C1001:92 SETS AS A PAST RECORD FOR LOW VISIBILITY OF THE FORWARD SENSING CAMERA (FSC). IT DOES NOT MEAN THERE IS AN ACTUAL FSC DEFECT. IN SOME CASES THE CUSTOMER MAY HAVE A CONCERN WITH THE LANE DEPARTURE WARNING SYSTEM (LDWS) AND/OR HIGH BEAM CONTROL SYSTEM (HBC). IN OTHER CASES THIS DTC MIGHT BE FOUND WITHOUT A RELATED CUSTOMER CONCERN.

FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.

DUE TO ASSEMBLY VARIATIONS, THE CLEARANCE BETWEEN THE SEAT BACK BAR GARNISH AND THE CONVERTIBLE TOP IS TOO SMALL ON SOME VEHICLES.

SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.

FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.

DUE TO ASSEMBLY VARIATIONS, THE CLEARANCE BETWEEN THE SEAT BACK BAR GARNISH AND THE CONVERTIBLE TOP IS TOO SMALL ON SOME VEHICLES.TO CORRECT THE CONCERN, THE LINK STOPPER OF CONVERTIBLE TOP HAS BEEN CHANGED TO ADJUST THE OPENING ANGLE AND FOLDING POSITION OF THE CONVERTIBLE TOP. THIS WILL INCREASE THE GAP BETWEEN THE SEAT BACK BAR GARNISH AND THE CON-VERTIBLE TOP WHEN FOLDED DOWN.

THE 2016 MX-5, 2016 CX-3 AND NEW 2016 CX-9 BSM SYSTEM VEHJICLE DETECTION HAS CHANGED. ALTHOUGH THE OVERALL FUNCTION IS THE SAME AS PREVIOUS VEJHICLES, VEHICLE DETECTION IS DIFFERENT.

To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.

This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.

view of the back window.

The rearview mirror (1) rattles up and down (2) while adjusting the mirror. 2. The rearview mirror (1) makes a rattle noise depending on the road surface conditions while driving. This concern is caused during rearview mirror installation. The adhesive is squeezed out between the windshield and the mirror base. The rearview mirror is assembled on top of the overextended adhesive. The adhesive is softened by heat, and loosening screws, results in a rattling concern.

This may be caused by the sun's reflection.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This is caused by: CASE A: The J-hook binding holding the inner cloth coming loose because the convertible top is opened/closed a lot or from high ambient temperatures. CASE B: After the previous improvement carried out at the supplier since January 19, 2016, some J-hooks have still been found coming loose to bind and hold the inner cloth during the assembly process. To correct the problem: CASE A: Two top-protector clips have been additionally installed to both side edges of the J-hook to prevent the J-hook from loosening and separating. CASE B: An improved inspection process has been started at the supplier to check the appearance of the inner cloth after installation of the clip.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

This may be caused by clogging in the roof drainpipe and improper drainage cleaning. Some customers may not be aware of the necessity of drainage cleaning and foreign matter (dust or fallen leaves) may accumulate in the drainpipe. Explain the necessity of the cleaning and its procedure described in the owners manual to the customer

end causing a poor appearance and obstructing the view of the back window.

This may be caused by the sun's reflection.

view of the back window.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.

This is caused by: CASE A: The J-hook binding holding the inner cloth coming loose because the convertible top is opened/closed a lot or from high ambient temperatures. CASE B: After the previous improvement carried out at the supplier since January 19, 2016, some J-hooks have still been found coming loose to bind and hold the inner cloth during the assembly process.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

color) instead of athe conventional methanol type (blue color). This change is for European compliance Mazda has decided to make the change for all markets.

Some vehicles may exhibit the driver andf/or passenger side tension band(S) (A) hanging down from the convertible top. Upon inspection, the plastic plate. To correct this issue, the configuration of the tension band will be changed to increase the strength

This is caused by the J-hook binding holding the inner cloth coming loose during the opening/closing of the convertible top, from vibration during driving or from high ambient temperatures. To correct the problem, two top-protector clips have been additionally installed to both side edges of the J-hook to prevent the J-hook from loosening and separating.

The console mat is fixed at both ends and warpage of the center part is caused by heat influence. To prevent the console mat from warping, double-sided adhesive tape (A) has been added between the console mat (B) and the console panel (C).

remedy, and warranty coverage (if applicable).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

The paint on the quarter glass guide gets damaged from vibration when the door is closed and when driving. This concern is caused by the beltline molding contacting the quarter glass guide due to production variances. To correct this concern, a spacer has been attached at the contact area to assure an appropriate clearance between the beltline molding and the quarter glass guide.

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may becaused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

remedy, and warranty coverage (if applicable).

Upon inspection, the plastic plate (A) of tension band is broken where it is riveted to the header panel (B). This is caused by insufficient strength of the plastic plate. To correct this issue, the configuration of the tension band will be changed to increase the strength. NOTE: The header panel is shown with the fabric top removed.

This concern happens especially when the door glass is wet with moisture or after a car wash. This is caused by stick-slip noise occurring at the contact surfaces between the door glass and the weather strip. With repeated moving up and down, the anti-noise paint on the weather strip peels off. To prevent the stick-slip noise, a polyester film has been attached at the applicable location of the weatherstrip.

The paint on the quarter glass guide gets damaged from vibration when the door is closed and when driving.This concern is caused by the beltline molding contacting the quarter glass guide due to production variances. To correct this concern, a spacer has been attached at the contact area to assure an appropriate clearance between the beltline molding and the quarter glass guide.

Warning System (LDWS) warning light turns ON while stopping or driving at a very slow speed. DTC C1001:92 (Poor functioning of Forward Sensing Camera (FSC)) is stored in memory. 2) High Beam Control (HBC) System warning light turns ON while stopping or driving at a very slow speed. DTC C1001:92 (Poor functioning of Forward Sensing Camera (FSC)) is stored in memory. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear).

WHEN THESE TYPES OF CLEANERS ARE USED TO CLEAN THE WHEELS ON MAZDA VEHICLES, THE CHEMICALS CONTENTS PENETRATE THE CLEAR COATING OF THE WHEEL SURFACE AND DAMAGE THE PAINT UNDER THE CLEAR COATING. THE DAMAGED AREA HAS THE APPEARANCE OF DARK STAINS.

THE HEADER PANEL (A) IS FORMED BY TWO ALUMINUM PANELS, INNER (B) AND OUTER (C). WHEN RECEIVING AN INPUT FORCE BY DRIVING ON A ROUGH ROAD, THE TWO PANELS AT THE PROBLEM AREA, WHERE SPOT WELDS ARE LOCATED (D), MAY WARP AND CHANGE RELATIVE POSITION CAUSING THE RATTLING NOISE. (F=FRONT)TO CORRECT THE PROBLEM, A SPOT WELD (E) HAS BEEN ADDED TO THE PROBLEM AREA, WHERE THE ORIGINAL SPOT WELDS ARE LOCATED (D), TO INCREASE THE RIGIDITY AND PREVENT THE WARPING.

THE HEADER PANEL (A) IS FORMED BY TWO ALUMINUM PANELS, INNER (B) AND OUTER (C). WHEN RECEIVING AN INPUT FORCE BY DRIVING ON A ROUGH ROAD, THE TWO PANELS AT THE PROBLEM AREA, WHERE SPOT WELDS ARE LOCATED (D), MAY WARP AND CHANGE RELATIVE POSITION CAUSING THE RATTLING NOISE. (F=FRONT)TO CORRECT THE PROBLEM, A SPOT WELD (E) HAS BEEN ADDED TO THE PROBLEM AREA, WHERE THE ORIGINAL SPOT WELDS ARE LOCATED (D), TO INCREASE THE RIGIDITY AND PREVENT THE WARPING.

THIS IS CAUSED BY THE J-HOOK BINDING HOLDING THE INNER CLOTH COMING LOOSE DURING THE OPENING/CLOSING OF THE CON-VERTIBLE TOP, FROM VIBRATION DURING DRIVING OR FROM HIGH AMBIENT TEMPERATURES.TO CORRECT THE PROBLEM, TWO TOP-PROTECTOR CLIPS HAVE BEEN ADDITIONALLY INSTALLED TO BOTH SIDE EDGES OF THE J-HOOK TO PREVENT THE J-HOOK FROM LOOSENING AND SEPARATING.

THE CONSOLE MAT IS FIXED AT BOTH ENDS AND WARPAGE OF THE CENTER PART IS CAUSED BY HEAT INFLUENCE. TO PREVENT THE CONSOLE MAT FROM WARPING, DOUBLE-SIDED ADHESIVE TAPE (A) HAS BEEN ADDED BETWEEN THE CONSOLE MAT (B) AND THE CONSOLE PANEL (C).

THERE IS NO DAMAGE ON THE INNER SURFACE. THE MARKS ARE LOCATED UPWARD OF THE DOOR GLASS REAR EDGE AND AROUND THE EDGE OF THE SOFT TOP STITCH. EACH MARK IS CAUSED FROM CONTACT WITH THE CONVERTIBLE TOP FRAME WHEN THE TOP IS OPENED AND CLOSED.

VIEW OF THE BACK WINDOW.THIS IS CAUSED BY THE J-HOOK BINDING HOLDING THE INNER CLOTH COMING LOOSE DURING THE OPENING/CLOSING OF THE CON-VERTIBLE TOP, FROM VIBRATION DURING DRIVING OR FROM HIGH AMBIENT TEMPERATURES.THIS IS CAUSED BY THE J-HOOK BINDING HOLDING THE INNER CLOTH COMING LOOSE DURING THE OPENING/CLOSING OF THE CON-VERTIBLE TOP, FROM VIBRATION DURING DRIVING OR FROM HIGH AMBIENT TEMPERATURES.TO CORRECT THE PROBLEM, TWO TOP-PROTECTOR CLIPS HAVE BEEN ADDITIONALLY INSTALLED TO BOTH SIDE EDGES OF THE J-HOOK TO PREVENT THE J-HOOK FROM LOOSENING AND SEPARATING.

THIS CONCERN HAPPENS ESPECIALLY WHEN THE DOOR GLASS IS WET WITH MOISTURE OR AFTER A CAR WASH.THIS IS CAUSED BY STICK-SLIP NOISE OCCURRING AT THE CONTACT SURFACES BETWEEN THE DOOR GLASS AND THE WEATHER STRIP. WITH REPEATED MOVING UP AND DOWN, THE ANTI-NOISE PAINT ON THE WEATHER STRIP PEELS OFF. TO PREVENT THE STICK-SLIP NOISE, A HIGH SLIDE-ABILITY TAPE HAS BEEN ADDED TO THE WEATHER STRIP.

THIS IS CAUSED BY THE J-HOOK BINDING HOLDING THE INNER CLOTH COMING LOOSE DURING THE OPENING/CLOSING OF THE CON-VERTIBLE TOP, FROM VIBRATION DURING DRIVING OR FROM HIGH AMBIENT TEMPERATURES.TO CORRECT THE PROBLEM, TWO TOP-PROTECTOR CLIPS HAVE BEEN ADDITIONALLY INSTALLED TO BOTH SIDE EDGES OF THE J-HOOK TO PREVENT THE J-HOOK FROM LOOSENING AND SEPARATING.

THE CONSOLE MAT IS FIXED AT BOTH ENDS AND WARPAGE OF THE CENTER PART IS CAUSED BY HEAT INFLUENCE. TO PREVENT THE CONSOLE MAT FROM WARPING, DOUBLE-SIDED ADHESIVE TAPE (A) HAS BEEN ADDED BETWEEN THE CONSOLE MAT (B) AND THE CONSOLE PANEL (C).

SOME VEHICLES MAY EXHIBIT A RATTLE NOISE (A) FROM THE HEADER PANEL (B) OF THE CONVERTIBLE TOP WHEN DRIVING ON A ROUGHT ROAD. THE HEADER PANEL (A) IS FORMED BY TWO ALUMINUM PANELS, INNER (B) AND OUTER (C).

SOME VEHICLES MAY EXHIBIT A RATTLE NOISE (A) FROM THE HEADER PANEL (B) OF THE CONVERTIBLE TOP WHEN DRIVING ON A ROUGH ROAD.

THIS CONCERN IS MOST LIKELY TO BE FOUND IN COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEN PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED ARE TO REMOVE STAIN(S).

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

vehicle service.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit. Tool Number Description Pricing PC1923MAZ Pro-Cut On-Car Brake Lathe Check eStore or call for current pricing OBTAINING TOOLS This tool can be ordered through Mazda eStore. You can log on to eStore at: http://dealers.mazdausa.com CUSTOMER SERVICE INFORMATION For warranty or product information contact Mazda Authorized Service Equipment at 877-768-6657. Customer service representatives are available from 7:30 AM until 7:00 PM CST, Monday through Friday. SPECIAL SERVICE TOOL (SST) PART NAME: OVERVIEW Pro-Cut On-Car Brake Lathe PART NUMBER: PC1923MAZ APPLICABLE MODELS: All USAGE: To machine brake rotors on the vehicle.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.

Vibration from the road surface shakes the brake caliper causing the brake pads in the caliper to move and hit the caliper support. The noise will disappear when the parking brake is lightly applied. To correct the problem, the rear brake caliper support and rear brake pads have been changed.

properly initialize the system.The Tire Pressure Monitoring System (TPMS) monitors the tire pressure of all four tires indirectly using the data sent from the ABS wheel speed sensors. If the air pressure of one or more tires is too low compared with the specified value (the initial value learned by the system), the system warns the driver with the TPMS warning light in the instrument cluster and a beep sound. To allow the TPMS to operate correctly, it is essential that the TPMS be initialized to learn new conditions whenever a tire related service is performed.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare subject to denial or debit.

vehicle service.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

This noise is caused by the upper part of the speaker interfering with the headrest pad. To correct the concern, the shape of the headrest pad will be changed to create sufficient clearance between the speaker and the headrest pad.

IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.

THE OWNER'S MANUAL PROVIDES 7 EXAMPLES: OBJECTS ON THE ROAD AT THE ENTRANCE TO A CURVE.VEHICLES PASSING IN THE OPPOSITE LANE WHILE MAKING A CURVE.METAL OBJECTS, BUMPS, OR PROTRUDING OBJECTS ON THE ROAD.WHEN PASSING THROUGH A TOLL GATE.WHEN PASSING UNDER A VINYL CURTAIN OR FLAG.PLASTIC OBJECTS SUCH AS PYLONS.TWO-WHEELED VEHICLES, PEDESTRIANS, ANIMALS OR STANDING TREES.THIS M-TIP ARTICLE PROVIDES 2 ADDITIONAL EXAMPLES:A. THERE IS FOGGING ON THE INNER SURFACE OF THE WINDSHIELD.B. THERE IS/ARE FOGGING/WATER DROPS ON THE OUTER SURFACE OF THE WINDSHIELD.THE NEAR INFRARED LASER BEAM IS A LIGHT BEAM AND IS REFRACTED BY WATER DROPS OR FOREIGN MATERIAL ON THE WINDSHIELD. IN THIS CASE, THE NEAR INFRARED LASER BEAM MAY NOT DETECT AN OBSTRUCTION AHEAD CORRECTLY.

THIS CONCERN MAY BE CAUSED BY THE TOP TWO WINDINGS OF THE REAR SHOCK ABSORBER COIL SPRING (A) INTERFERING WITH ONE ANOTHER AND CAUSING A STICK-SLIP NOISE.TO CORRECT THE CONCERN, A RESIN PROTECTOR (A) HAS BEEN INSTALLED ONTO THE COIL SPRING.

THIS CONCERN MAY BE CAUSED BY THE TOP TWO WINDINGS OF THE REAR SHOCK ABSORBER COIL SPRING (A) INTERFERING WITH ONE ANOTHER AND CAUSING A STICK-SLIP NOISE.TO CORRECT THE CONCERN, A RESIN PROTECTOR (A) HAS BEEN INSTALLED ONTO THE COIL SPRING.

This is considered normal and NO repair should be performed. During production, differential ring and pinion gears receive a manganese phosphate coating (commonly referred to as black oxide). This coating forms a porous, oil-retentive surface that improves boundary lubrication and reduces adhesive wear during initial contact cycles. Designed as a sacrificial layer, it is gradually removed under load throughout the break-in process. As a result, after the first few hundred miles, or at the initial gear oil service interval, the lubricant may appear darkened by the worn-off coating. It will contain trace ferrous particles from the normal run-in of the gear teeth and bearing surfaces. This condition is expected and does not, by itself, indicate an issue with the differential or PTO gears.

essential to first classify the issue into one of three primary categories: Noise, Vibration, or Harshness. Many customer complaints may involve overlapping symptoms, such as both noise and vibration, so identifying the dominant characteristic is critical. Once the primary symptom is determined, follow the appropriate diagnostic path. For example, if a concern includes both noise and vibration but is related to vehicle speed, the vibration diagnostic path should be followed. When considering component replacement during the diagnostic process, it is best practice to start with the lowest cost or most accessible part unless diagnostic evidence clearly identifies a more expensive or complex component as the root cause. This approach helps minimize repair costs and avoids unnecessary part replacements. For example, a growling or bearing whine noise may be mistakenly attributed to internal components in the differential, transfer unit, or transmission, when the actual source is a wheel bearing. Misdiagnosis like this can lead to unnecessary repairs, added time and cost. To help prevent this, always follow the guidelines in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.

the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.

The system performance has been improved as follows: Ver. 74.00.324 fixes these software errors (bugs): * If the shift lever is operated quickly while displaying the CarPlayTM screen, the rear view screen may not return to the CarPlayTM screen. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into the R position.

configuration.

As the vehicle mileage increases, the ATF color changes. The color change does not affect vehicle performance.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Use a clean towel damped in leather/vinyl cleaner or mild soap to clean the steering wheel. NOTE: Upholstery maintenance and care information can also be found in the Owner's Manual.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

NOTE: The following Caution is included with every ATX that requires configuration.

Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the oil cooler was missing altogether. IMPORTANT NOTE: ALWAYS REMEMBER TO INCLUDE THE ORIGINAL OIL COOLER WITH THE RETURNED TRANSMISSION CORE!

of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

configuration.

Using the wrong ATF may cause shift quality complaints or may even damage the transmission. NOTE: ATF M-V (TYPE M5) IS NOT THE SAME FLUID AS MERCONV OR MERCONLV ATF. ATF M-V (TYPE M5) HAS A GREATER VISCOSITY THAN MERCONV AND MERCONLV ATF IN LOW TEMPERATURES. ATF M-V (TYPE M5) HAS A GREATER ANTI-JUDDER SPECIFICATION THAN MERCONV AND MERCONLV ATF. TRANSMISSION FLUID FLUSHING SHOULD ONLY BE PERFORMED WHEN INSTRUCTED BY THE WORKSHOP MANUAL OR ANY OTHER MAZDA PUBLICATION.

button cover during installation. 1. Install the lock release button cover (A) in the select lever knob. a. Set the hook (B) of the cover in the select lever knob. b. Push in on the lower edge of the cover in the direction of the arrow to snap the tab (C) into place.

USING THE WRONG ATF MAY CAUSE SHIFT QUALITY COMPLAINTS OR MAY EVEN DAMAGE THE TRANSMISSION.NOTE: ATF M-V (TYPE M5) IS NOT THE SAME FLUID AS MERCONV OR MERCONLV ATF. ATF M-V (TYPE M5) HAS A GREATER VISCOSITY THAN MERCONV AND MERCONLV ATF IN LOW TEMPERATURES. ATF M-V (TYPE M5) HAS A GREATER ANTI-JUDDER SPECIFICATION THAN MERCONV AND MERCONLV ATF. TRANSMISSION FLUID FLUSHING SHOULD ONLY BE PERFORMED WHEN INSTRUCTED BY THE WORKSHOP MANUAL OR ANY OTHER MAZDA PUBLICATION. CAUTION: USING ATF OTHER THAN ATF M-V (TYPE M5) IN AUTOMATIC TRANSMISSIONS DESIGNED TO USE ATF M-V (TYPE M5) MAY CAUSE SHIFT QUALITY COMPLAINTS. USING ANY OTHER ATF OTHER THAN THE SPECIFIED ATF IN AUTOMATIC TRANSMISSIONS MAY CAUSE TRANSMISSION DAMAGE. USING A GENERIC, MULTI-PURPOSE OR UNIVERSAL ATF MAY CAUSE TRANSMISSION DAMAGE. DAMAGE TO THE TRANSMISSION CAUSED BY USING THE INCORRECT ATF, OR A GENERIC, MULTI-PURPOSE OR UNIVERSAL ATF WILL NOT BE COVERED BY WARRANTY.

VEHICLE ACCELERATES/DECELERATES RAPIDLY. THIS IS CAUSED BY A STICK-SLIP NOISE OCCURRING AT THE CONTACT SURFACE BETWEEN THE POWER PLANT FRAME (PPF) (A) AND THE REAR DIFFERENTIAL. TO ELIMINATE THIS CONCERN, THE TIGHTENING TORQUE OF THE STUD BOLTS AND NUTS HAS BEEN INCREASED.

SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owners Manual, Workshop Manual, Technical Service Bulletin, etc.).

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface.

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

The marks may occur on the right and/or left side(s). This is caused by the top fabric receiving vibration and the stitching line (hard) touching the top fabric while the vehicle is running with the convertible top opened (top fabric folded and piled up). To correct this concern, the link stopper of the convertible top has been changed to adjust the opening angle of the convertible top, thereby decreasing the contact pressure applied to the top fabric when folded and piled up. NOTE: Compared to the top fabric with inner cloth, the top fabric without inner cloth is more likely to have this concern because the folded height is set lower, therefore the top fabric is folded and piled up in more tight condition.

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

NOTE: You may see ?Selection not available? on IDS when a selecting ?Programming menu?, 108.07 included a timer extension for Programming menu application that had to be installed before the expiration date of 3/27/18. After the expiration, IDS can?t accept the extension. To correct this, uninstall IDS and re-install IDS 108.00 >IDS 108.07 up-date. Select "Remove Mazda data files and settings" as shown below.

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear incertain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Damage can occur when using some cleaners that contain strong acid, alkaline cleanser or organic solvent. Damage caused by using these cleaners is not covered by Mazda's New Vehicle Limited Warranty term.

THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMP-TOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM.

ALTHOUGH THE OVERALL FUNCTION IS THE SAME AS PREVIOUS VEHICLES, VEHICLE DETECTION IS DIFFERENT. FOR DETAILED BSM SYSTEM INFORMATION, REFER TO SERVICE HIGHLIGHTS.

The following are possible causes of floor mat interference, which can be avoided with proper usage.

However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts. CAUTION: Be aware that when cleaning the brand emblem, never use cleaning products that are highly acidic/alkaline detergent, organic solvents or those with aggressive chemical products, otherwise, the brand emblem may become cracked and/or deformed (as shown in the example below). Always refer customers to the owners manual for proper cleaning using cold or lukewarm water and a mild, neutral detergent.

The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.

THE SST WILL BE SHIPPED AUTOMATICALLY BY MAZDAS TOOL VENDOR BOSCH DURING THE MONTH OF NOVEMBER 2015.

THE SSTS WILL BE SHIPPED AUTOMATICALLY BY MAZDAS TOOL VENDOR BOSCH IN THE MONTH OF OCTOBER, 2015. THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST.

SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.THIS SERVICE BULLETIN IS ONLY FOR SUBLET REPAIR. A QUALIFIED UPHOLSTERY REPAIR SPECIALIST IS REQUIRED FOR THIS REPAIR PROCEDURE. PLEASE PRINT A COPY OF THIS BULLETIN FOR THE UPHOLSTERY REPAIR SPECIALIST.

SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.THIS SERVICE BULLETIN IS ONLY FOR SUBLET REPAIR. A QUALIFIED UPHOLSTERY REPAIR SPECIALIST IS REQUIRED FOR THIS REPAIR PROCEDURE. PLEASE PRINT A COPY OF THIS BULLETIN FOR THE UPHOLSTERY REPAIR SPECIALIST.

be wet.

be wet.

be wet.

This includes the use of intermediate positions.

Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.

UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR).OTE FOR CUSTOMER: THE FSC MAY NOT WORK PROPERLY UNDER THE CONDITIONS:THE WINDSHIELD IS NOT CLEAR. THE FSC LENS IS NOT CLEAR. DRIVING IN HEAVY RAIN, DENSE FOG OR SNOW, OR INTO THE SUN. DRIVING ON A ROAD WITH NO OR BLURRED ROAD LANE MARKINGS. WHEN THE WINDSHIELD BECOMES FOGGY IN THE WINTER TIME OR OTHER COLD WEATHER CONDITIONS AND LDWS/HBC WARN-ING LIGHTS TURN ON, DRIVE WITH THE DEFROSTER ON FOR ABOUT 10 MINUTES. THIS WILL HELP CLEAR THE FOGGY WINDSHIELD AT THE FSC.

THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.

THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.

UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR).OTE FOR CUSTOMER: THE FSC MAY NOT WORK PROPERLY UNDER THE CONDITIONS:THE WINDSHIELD IS NOT CLEAR. THE FSC LENS IS NOT CLEAR. DRIVING IN HEAVY RAIN, DENSE FOG OR SNOW, OR INTO THE SUN. DRIVING ON A ROAD WITH NO OR BLURRED ROAD LANE MARKINGS. WHEN THE WINDSHIELD BECOMES FOGGY IN THE WINTER TIME OR OTHER COLD WEATHER CONDITIONS AND LDWS/HBC WARN-ING LIGHTS TURN ON, DRIVE WITH THE DEFROSTER ON FOR ABOUT 10 MINUTES. THIS WILL HELP CLEAR THE FOGGY WINDSHIELD AT THE FSC.

road.

Customers having this concern should have their vehicle repaired using the following repair procedure.

balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?

74.00.311 or later).

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.352 or later).

uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.

Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version.

The new version number is 59.00.502. Please refer to TSB 09-017/17 for a list of improvements to the system.

This is caused by the seat belt, seat belt guide and seat belt anchor (A) accumulating dust and dirt from hands and/or from the outside when driving with the top down. An increase in friction makes the seat belt retraction difficult. Keeping the seat belts clean will prevent this from happening.

because the shape of the seat belt guide is inadequate.

downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. When parked, new messages can be displayed or read by the system. When driving, new messages can be read to the vehicle occupants.

downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. When parked, new messages can be displayed or read by the system. When driving, new messages can be read to the vehicle occupants.

Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.

BECAUSE THE SHAPE OF THE SEAT BELT GUIDE IS INADEQUATE.TO CORRECT THE PROBLEM, THE SHAPE OF THE SEAT BELT GUIDE HAS BEEN CHANGED.

THIS IS CAUSED BY THE SEAT BELT, SEAT BELT GUIDE AND SEAT BELT ANCHOR (A) ACCUMULATING DUST AND DIRT FROM HANDS AND/OR FROM THE OUTSIDE WHEN DRIVING WITH THE TOP DOWN. AN INCREASE IN FRICTION MAKES THE SEAT BELT RETRACTION DIFFICULT. KEEPING THE SEAT BELTS CLEAN WILL PREVENT THIS FROM HAPPENING.

Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. E85: A blend of 85% ethanol and 15% gasoline All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V.

Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).

Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).

INSTEAD, THE WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING EVAP LEAK TESTER WILL BE USED TO TROUBLESHOOT EVAP SYSTEM LEAKS.

This may be caused by a loose spare tire jack.

This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.

THIS MAY BE CAUSED BY A LOOSE SPARE TIRE JACK.

rattling of the bush of the upper lateral link in the rear hub support. Dimensional variation of the bush boots in the rear hub support may cause insufficient sealing which allows water to enter the rear hub support, resulting in rust on the pillow-ball. The rust then accelerates the pillow-ball wear and causes a gap between the body and the bearing, resulting in the clunk noise during driving. To eliminate this concern, the boots in the rear hub support have been modified to improve sealing.