2023 Mazda MX-30 TSBs

The changes are noted in Red text. SA-042/26 06/30/26 DESCRIPTION Frequently Asked Questions (FAQ) Index General Questions MAZDA CONNECT Indication Setup and Getting Started Dealer Processes Registration / Enrollment / Take-Over Customer Subscription Status WI-FI General Informatio Opening the TCU Communication Line WI-FI How-To Conditions for Remote Engine Start Will Not Function WI-FI Trial Period Conditions for Remote Engine Start Function Will turn engine OFF Interacting With The App TCU Communication Line Status Service Issues Educational Videos Troubleshooting Resources MyMazda App Error Codes Customer Opt-Out

interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button

The changes are noted in Red text. SA-038/26 06/15/26 DESCRIPTION Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote functions inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\". Index MAZDA CONNECT 2 Center Display Status Icon MAZDA CONNECT 3 Center Display Status Icon Remote Engine Start Will Not Function Remote Engine Start Function Will turn engine OFF Customer Subscription Status TCU Communication Line Status

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\". Index MAZDA CONNECT 2 Center Display Status Icon MAZDA CONNECT 3 Center Display Status Icon Remote Engine Start Will Not Function Remote Engine Start Function Will turn engine OFF Customer Subscription Status TCU Communication Line Status

The changes are noted in Red text. SA-017/25 12/16/25, 09/08/25, 07/14/25, 05/15/25 and 03/21/25 DESCRIPTION Mazda Connect Frequently Asked Questions (FAQ) Index General Questions MAZDA CONNECT Indication Setup and Getting Started Dealer Processes Registration / Enrollment / Take-Over Customer Subscription Status WI-FI General Informatio Opening the TCU Communication Line WI-FI How-To Conditions for Remote Engine Start Will Not Function WI-FI Trial Period Conditions for Remote Engine Start Function Will turn engine OFF Interacting With The App TCU Communication Line Status Service Issues Educational Videos Troubleshooting Resources MyMazda App Error Codes Customer Opt-Out

The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.

The changes are noted below in Red. SA-029/25 10/16/25 and 06/02/25 DESCRIPTION This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure. REPAIR PROCEDURE HIGH VOLTAGE BATTERY MAINTENANCE Verify the State-of-charge (SOC) in the instrument cluster. MX-30 EV: If the SOC is lower than 26%, charge it to 50% (either by normal charging or quick charging). CX-90/CX-70 PHEV: If the SOC is lower than 1%, charge it to 10% (either by normal charging, quick charging or engine running).

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). Only Mazda-approved key cutting machines can process these 10-digit codes. Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\". Page

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

whine, groan, rattle or squeak) coming from the front combination lights when turning them on, or a few minutes after turning them off. The noise may be due to contamination by foreign matter during the manufacturing process and the fan motor bearing may become worn out during use. To eliminate this concern, the fan motor has been modified. NOTE: It is normal for some noise to occur within the first few seconds after starting the engine, when the front combination lights perform a self check (sweep).

Foreign debris on the blower motor after servicing the cabin air filter may be the cause. During the removal of the cabin air filter, foreign debris (leaves, dust, dirt....ect.) may fall on the blower motor causing a fluttering type noise or odor.

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

power consumption is restricted, thereby extending the transmitter battery life and the following will occur: The engine will not start unless the key transmitter is held over the Start Stop button. Outside door handle lock/unlock touch sensor is inoperative. Key transmitter indicator lights are inoperative. The following DTC's may be stored: DTC B13D3:94 (Communication error with remote transmitter) DTC P1260:00 (Immobilizer system problem).

power consumption is restricted, thereby extending the transmitter battery life. NOTE: Some customers may complain about an engine no start. This may be caused by the customer inadvertently putting the key transmitter in Power Saving Function.

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control

MX-30 and PHEV vehicles do not have a Remote Engine Start function; instead, they are equipped with the following remote functions: Start / Stop Charge Climate On / Off

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. The auto close operation of the power liftgate is not performed (The liftgate can be closed manually). To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified. Customers

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control

If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified.

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF, Climate control

Processes, Registration / Enrollment, TCU Activation, WI-FI General Information, Conditions for Remote Engine Start Will Not Function, WI-FI How-To Conditions for Remote Engine Start Function Will turn engine OFF, WI-FI Trial Period, Deactivation Mode, Interacting With The App, Educational Videos, Service Issues, Resources, Troubleshooting Page.

Processes, Registration / Enrollment, TCU Activation, WI-FI General Information, Conditions for Remote Engine Start Will Not Function, WI-FI How-To Conditions for Remote Engine Start Function Will turn engine OFF, WI-FI Trial Period, Deactivation Mode, Interacting With The App, Educational Videos, Service Issues, Resources, Troubleshooting Page.

Processes Registration / Enrollment TCU Activation WI-FI General Informatio Conditions for Remote Engine Start Will Not Function WI-FI How-To Conditions for Remote Engine Start Function Will turn engine OFF WI-FI Trial Period Deactivation Mode Interacting With The App Educational Videos Service Issues Resources Troubleshooting Page

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

whine, groan, rattle or squeak) coming from the front combination lights when turning them on, or a few minutes after turning them off. The noise may be due to contamination by foreign matter during the manufacturing process. The fan motor bearing may become worn out during use. To eliminate the noise, the production process at the supplier and the material has been modified. NOTE: It is normal for some noise to occur within the first few seconds after starting the engine, when the front combination lights perform a self check (sweep).

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

whine, groan, rattle or squeak) coming from the front combination lights when turning them on, or a few minutes after turning them off. The noise may be due to contamination by foreign matter during the manufacturing process. The fan motor bearing may become worn out during use. To eliminate the noise, the production process at the supplier and the material has been modified. NOTE: It is normal for some noise to occur within the first few seconds after starting the engine, when the front combination lights perform a self check (sweep).

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF, 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative.Engine Start / Stop,Door Lock / Unlock,Lights ON / OFF. 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

The changes are noted in Red text. SA-006/23 01/23/23 DESCRIPTION Some customers may complain about the infotainment system and/or the MyMazda App showing incorrect clock and/or tire pressures and/or tire pressure missing. This may be caused by: Incorrect calendar entry (month/day/year) after a battery disconnect Infotainment system software update. BCM TPMS unlearn during vehicle storage or transport. Wheel/Tire change REPAIR PROCEDURE This can be corrected by the customer driving the vehicle for a day or two so that the following will occur.

The changes are noted below in Red. SA-027/26 04/16/26 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. REPAIR PROCEDURE 1. Perform appropriate repair to vehicle. If needed, use the Battery Diagnostics of the DCA-8000 to test the charging and starting systems by following the on-screen instructions for entering the appropriate information. Refer to the Mazda DCA-8000 Instruction Manual for more information.

The changes are noted below in Red. SA-007/25 10/22/25, 06/02/25 and 02/03/25 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a batterys Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries. TEST PROCEDURE 1. Connect the charger clamps to the appropriate battery posts.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery.

Removing the charging cable while it is energized can cause sparks because the airs insulation breaks down. To eliminate this concern, the control logic of the PCM has been modified to temporarily stop AC charging upon a door unlock trigger.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a batterys Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result

This is due to improper PAU (Parking Assist Unit) control software. To eliminate this concern, the PAU control software has been modified.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

When the front door is being closed with a hand touching one or both of the touch sensors on the front outer handle, the out-of-area (reception area) type auto lock function may fail. Control software of the LF control unit (LFU) has been modified.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

Radio station selection (AM, FM, SiriusXM) changes unintentionally after turning the ignition on. Audio source cannot be changed. Diagnosing according to MGSS online does not solve the problem. These concerns may be caused by the remote tuner not operating properly under certain situations. To eliminate these concerns, the remote tuner control software has been modified.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.

lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

When the front door is being closed with a hand touching one or both of the touch sensors on the front outer handle, the out-of-area (reception area) type auto lock function may fail. Control software of the LF control unit (LFU) has been modified.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.

The changes are noted in Red text. SA-038/26 08/18/26 and 06/15/26 DESCRIPTION Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App

VIEW VEHICLE STATUS MONITOR FOR DETAILS" on the center display even after the recall has been completed. NOTE: Once the warranty claim for the recall campaign is approved by Mazda Japan, the recall notification will be automatically removed via Connected Services on the following day or later. This condition may occur if the Connected Services subscription was canceled while the recall notification was still active. ACTION TO BE TAKEN If you encounter the situation above, use MDARS to manually remove the center display recall notification. Note: MDARS can only remove the recall notification when MCVV shows no CV contract.

The changes are noted in Red. SA-009/25 08/22/25 and 02/18/25 DESCRIPTION Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs. Index System Outline MYMAZDA App Connected Vehicle (CV) Error Codes Vehicle Confirmation Instructions Troubleshooting Instructions Resources

The changes are noted in Red text. SA-012/25 10/06/25, 08/21/25, 05/15/25 and 02/27/25 DESCRIPTION Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE NOTE: Before proceeding: Document the vehicle's current MAZDA CONNECT CMU software version. 2019-2022 Models - Go to TSB 16-003/23 and confirm the CMU Serial Number is not within the affected range. Document customer device Brand/Model/Model Number/software version on the repair order. Confirm that the Connectivity Master Unit (CMU) is updated to the latest software version. Go to MGSS -> Infotainment -> MAZDA CONNECT Updates If possible, complete the Microsoft Forms Questionnaire. Go to MGSS -> Infotainment -> MAZDA CONNECT Questionnaire.

Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with an active SAT radio.

Navigation Data Unavailable" or "Check Navigation SD Card" in the meter while driving.

The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs.

NOTE: When the warranty claim for the recall campaign is accepted at Mazda Japan, the recall notification will be automatically deleted via the Connected Service on the next day or later. This situation occurs if the Connected Service subscription has been cancelled while the recall notifications remain.

The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs.

DTC U3000:04 (FSC) is stored in memory DTC U3000:04 (FSC) - Forward sensing camera (FSC) internal malfunction This may be caused by a hardware failure in an internal device of the FSC that results in the malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

navigation information.

The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs.

As this phenomenon is not a system failure, do not make any repairs or replace any parts. Explain the cause of this occurrence to the customer as follows: The 360view monitor is a system that provides a complete picture of the vehicle surroundings by combining the pictures captured by 4 separate cameras. These cameras are installed in the front, rear, right and left sides of the vehicle. Each camera has a color adjustment function (white balance) that operates independently from each other, which can result in color discrepancy when the combined picture is displayed on the screen. This is especially true when one of the cameras captures more green objects than the remaining cameras.

As this phenomenon is not a system failure, do not make any repairs or replace any parts.

This concern may be caused by the remote tuner not operating properly under certain situations. To eliminate this concern, the remote tuner control software has been modified.

This concern may be caused by the remote tuner not operating properly under certain situations. To eliminate this concern, the remote tuner control software has been modified.

navigation information.

As a reminder, dealers have 90 days, after the order is placed, to return the exchanged part. Failure to return the exchanged part will result in a debit of the full component price. It is highly recommended to set a calendar reminder at the time of the order for no more than 60 days to ensure all orders are returned if repaired and if not repaired, contact the customer to cancel the order and return the unit.

navigation information.

NOTE: iPod, iPhone, and Apple CarPlayTM are registered trademarks of Apple Inc. Android and Android AutoTM are registered trademarks of Google LLC. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. (Ver. 7000C0A-NA10_10004) fixes these software errors (bugs): The screen does not show proper picture when receiving SiriusXM data.

There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. Wrinkles may not be completely removed after the repair is completed. Leather is a natural material and may develop some wrinkles due to aging and wear during normal useage.

seat back surface.

seat back surface.

seat back surface.

The pads wear down by about 0.1 in (3 mm) every 6200 miles (10,000 km), and may require replacement at less than 12,400 miles (20,000 km). This is caused by intrusion of dirt and sand into the gap between the pad and the rotor. To eliminate this concern, the shape of the dust cover has been changed, and the brake pad chamfer shape has been revised.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.

The pads wear down by about 0.1 in (3 mm) every 6200 miles (10,000 km), and may require replacement at less than 12,400 miles (20,000 km). This is caused by intrusion of dirt and sand into the gap between the pad and the rotor. To eliminate this concern, the shape of the dust cover has been changed.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle.

This is due to rust on the rear brake disc plate. The brake pad has insufficient disc-rust prevention performance, resulting in the disc plate rusting. To eliminate this concern, the pad material has been improved to prevent rust on the disc surface. Symptom 2: Some vehicles may exhibit a squeal noise from the rear brakes when braking lightly while driving at a slow speed. The squeal noise is caused by the disc pad surface fluctuating. To eliminate this concern, the brake pads have been modified.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

This is due to rust on the rear brake disc plate. The brake pad has insufficient disc-rust prevention performance, resulting in the disc plate rusting. To eliminate this concern, the pad material has been improved to prevent rust on the disc surface. Symptom 2: Some vehicles may exhibit a squeal noise from the rear brakes when braking lightly while driving at a slow speed. The squeal noise is caused by the disc pad surface fluctuating.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

This is due to rust on the rear brake disc plate. Symptom 2: Some vehicles may exhibit a squeal noise from the rear brakes when braking lightly while driving at a slow speed. The squeal noise is caused by the disk pad surface fluctuating.

Inq. -> RECALLS / SPECIAL SERVICE PROGRAMS -> Status) and check for Open campaigns. If any of the following campaigns are open, complete the campaign before proceeding with this service information. SSPC5 - 2019-2021 MAZDA3 AND 2020-2021 CX-30 - CONTROL UNITS REPROGRAMMING 4219L - 2019MY MAZDA3 SUDDEN DECELERATION FROM FALSE BRAKE ACTIVATION 2024 CX-90 with VINS lower than JM2KK******151673 (produced before November 25, 2023), VCM software update available using TSB 15-001/24. DESCRIPTION This information will give you the necessary knowledge to respond to customers concerns of Smart Brake Support (SBS) unintended braking. By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle. IMPORTANT: Humans recognize an object with their eyes and decide whether or not to apply the brakes using their brain. The vehicle recognizes objects using the Forward Sensing Camera (FSC) and Front Radar sensor (FR), to determine brake application. Therefore, drivers may feel that the operation does not match the human feeling.

By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

This is due to rust on the rear brake disc plate. Symptom 2: Some vehicles may exhibit a squeal noise from the rear brakes when braking lightly while driving at a slow speed. The squeal noise is caused by the disk pad surface fluctuating.

The changes are noted in Red text. SA-047/25 10/07/25 DESCRIPTION When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated. CAUTION: DO NOT swap TCU with another vehicle as the TCU is VIN locked after activation. A TCU swap with another vehicle will disable Connected Services on both vehicles. If TCU activation is not performed, connected vehicle functions will not operate. This will have a negative impact on the customer because they will need to return to the dealer for repairs. If the Telematics Control Unit (TCU) replacement is necessary, check "Vehicle Communication Line Status Reference" status detail first. The TCU can only be replaced under the following "Status Detail" conditions: Open Completed (OK) Closed Completed (OK) If the TCU is replaced under the following "Status Detail" conditions, the customer may not be able to enroll into the replacement TCU. Processing (NG) Request Failed (NG) Open Failed (NG) Flag Setting Failed TCU Activation 1. Install the new TCU.

SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owners Manual, Workshop Manual, Technical Service Bulletin, etc.).

new upholstery is installed under Warranty repair. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. Wrinkles may not be completely removed after the repair is completed. Leather is a natural material and may develop some wrinkles due to aging and wear during normal usage.

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface.

This may be caused by light glare on the SST.

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

unit internal malfunction) stored.

Connected Vehicle Reception Icon shows "X".

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.

DTC U3000:04 STORED (DOES NOT APPLY TO 09-001/23)

To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.

This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.

This condition may be caused by worn or contaminated wiper blades. It can also be caused by bent wiper arms, or loose wiper arm retaining nuts due to improper handling. Improper handling occurs when pulling on or forcing the wiper arms. Technicians should be aware that while replacement of the wiper blade may resolve some cases, correction of bent components or repositioning of the wiper arms, particularly when the retaining nut is loose, requires additional steps to ensure proper alignment and function.

This may be caused by the lower window cable corrosion and damage. To eliminate this concern, the following improvements have been made: The shape of the power window regulator pulley has been modified to prevent cable damage. The shape of the carrier plate has been modified to prevent the cable from being exposed to water/moisture.

This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

The charge lid may or may not be missing.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

The charge lid may or may not be missing.

This may be caused by the sun's reflection.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.

Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.

Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.

(Emergency call unit/telematics communication unit internal malfunction) or U3000:04-TCU (Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.

(Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.

(Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.

(Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.

(Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.

(Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.

U3000:04-TCU (Telematics communication unit internal malfunction) stored after the connected service contract has been discontinued. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified

Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.. CAUTION: DO NOT swap TCU with another vehicle as the TCU is VIN locked after activation. A TCU swap with another vehicle will disable Connected Services on both vehicles. If TCU activation is not performed, connected vehicle functions will not operate. This will have a negative impact on the customer because they will need to return to the dealer for repairs.

The changes are noted in Red text. SA-039/26 06/15/26 Mazda Connect Symptom Troubleshooting DESCRIPTION Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.

Some vehicles may have steering wheel stains caused by chemicals such as hand lotions.

Some vehicles may have steering wheel stains caused by chemicals such as hand lotions.

driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).

Some vehicles may have steering wheel stains caused by chemicals such as hand lotions.

driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).

essential to first classify the issue into one of three primary categories: Noise, Vibration, or Harshness. Many customer complaints may involve overlapping symptoms, such as both noise and vibration, so identifying the dominant characteristic is critical. Once the primary symptom is determined, follow the appropriate diagnostic path. For example, if a concern includes both noise and vibration but is related to vehicle speed, the vibration diagnostic path should be followed. When considering component replacement during the diagnostic process, it is best practice to start with the lowest cost or most accessible part unless diagnostic evidence clearly identifies a more expensive or complex component as the root cause. This approach helps minimize repair costs and avoids unnecessary part replacements. For example, a growling or bearing whine noise may be mistakenly attributed to internal components in the differential, transfer unit, or transmission, when the actual source is a wheel bearing. Misdiagnosis like this can lead to unnecessary repairs, added time and cost. To help prevent this, always follow the guidelines in the repair procedure.

seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.

the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.

be wet.

be wet.

This is caused by: Improper dimensional accuracy of the lid actuator lock mechanism Incomplete control logic in the R-ESU software To eliminate this concern: The mold design of the lid actuator was modified. The control software of the R-ESU was revised.

Sidewall waviness/indentations/undulations are common on radial tires and are more noticeable on tires with taller sidewalls. The higher the tire pressure, the more noticeable the effect will be. Be sure to set the tire pressures at the recommended tire pressure on the vehicle tire label. Sidewall indentations are a cosmetic condition that does not affect the performance of the tires.

This is caused by the seat belt buckle resting against the seat.

This may caused by the onboard charger not being compatible with some brand chargers. NOTE: For reference, EVTronic," and "Alpitronic brands are reported as the inapplicable type of DC charger at this moment. To eliminate this concern, the control software of the onboard charger has been modified.