2008 Mazda Mazdaspeed3 TSBs

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

THIS CONCERN WILL MOST LIKELY OCCUR DURING THE VEHICLES FIRST FORWARD MOVEMENT AFTER STARTING THE ENGINE. THIS IS A NORMAL OPERATING NOISE OF THE ANTI-LOCK BRAKE SYSTEM (ABS). DO NOT ATTEMPT ANY REPAIRS.

THE REPAIR PROCEDURE FLOWCHART, REPAIR PROCEDURE AND WARRANTY INFORMATION HAVE BEEN REVISED. ALSO INCLUDED MODEL MAZDASPEED3 MODEL YEAR 2010 *JS

DUE TO WEAR ON LOCK PIN HOLE IN VVT ROTOR OR BREAKAGE OF VVT CASE, LOUD TICKING NOISE (KNOCKING/RATTLE) IS HEARD, FROM TIMING COVER AND/OR VALVE (CYLINDER HEAD) COVER, WHEN ENGINE IS STARTED AFTER COLD CONDITION. *PE

DUE TO INSUFFICIENT CRANK CASE VENTILATION, HEAVY WHITE SMOKE APPEARS FROM EXHAUST PIPES, AFTER LONG IDLE PERIODS, RESULTING IN OIL LEAKAGE PAST EXHAUST TURGINE SHAFT SEAL. *PE UPDATED 5/14/12. *PE UPDATED 12/18/12. *PE

THIS MAY BE CAUSED BY DAMAGE TO THE VALVE NUT AND/OR VALVE STEM OF THE WHEEL. *KB

*RM UPDATED 4/18/2012. *KB

THIS COULD BE CAUSED BY OIL PROBLEMS. *RM

DURING LONG PERIODS OF SLOW SPEED OR IDLING THERE MAY BE WHITE/BLUE SMOKE COMING FROM THE TAILPIPE. THERE COULD BE PROBLEM WITH THE TURBOCHARGER. *RM

PROBLEM IS DUE TO THE ACCUMULATION OF CARBON DEPOSITS INSIDE THE THROTTLE BODY CAUSING AIR FLOW TO DECREASE. *PE

*NJ

*NJ

*NJ

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

Operations is 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.

To determine the location of the evaporative system leak, follow the repair procedure below. P0441 - Evaporative emission control system incorrect purge flow P0442 - EVAP system leak detected (small leak) P0455 - EVAP system leak detected (gross leak) P0456 - EVAP system leak detected (very small leak) NOTE: P0441 is a DTC for purge flow, however, it can be stored when evaporative emissions are leaking from the fuel filler cap. Evaporative emissions leak from the fuel filler cap when the cap is not closed properly after refueling. When diagnosing an evaporative emissions leak from the fuel filler cap, DO NOT TOUCH the fuel filler cap.

*RM

SOME VEHICLES MAY HAVE A MIL ILLUMINATION WITH DTCS STORED IN MEMORY. *PE UPDATED 4/18/11. *PE

It has been unpublished and superseded by the Field Quality Information Report (FQIR) reporting system.

The following are possible causes of floor mat interference, which can be avoided with proper usage.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

remedy, and warranty coverage (if applicable).

VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE SPEEDOMETER REPLACE-MENT LABEL. LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.

This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.

EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. PLEASE CONTACT THE APPROPRIATE SOURCE BY REFERRING TO THE FOLLOWING TABLES.

VEHICLES WITH VIN'S LOWER THAN JM1 BK**** **823850 (PRODUCED BEFORE SEPT. 11, 2007). *NJ