2020 Mazda Mazda6 TSBs

2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a Software Update record for the PCM when using MDARS or IDS. MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. IDS Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealers expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.

As a result, PYFD-15-16ZA is no longer available. PW5S-15-16Z is supplied with a dummy plug pre-installed. Critical Installation Requirement: When replacing PW5S-15-16Z, the Powertrain Control Module (PCM) must also be updated to the latest software version. Failure to perform the PCM update may result in drivability concerns or diagnostic trouble codes.

2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a Software Update record for the PCM when using MDARS or IDS. MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. IDS Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealers expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.

2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a Software Update record for the PCM when using MDARS or IDS. MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. IDS Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealers expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). Only Mazda-approved key cutting machines can process these 10-digit codes. Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.

following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.

following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.

2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a Software Update record for the PCM when using MDARS or IDS. MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. IDS Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealers expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.

2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a Software Update record for the PCM when using MDARS or IDS. MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. IDS Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealers expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.

2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a Software Update record for the PCM when using MDARS or IDS. MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. IDS Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealers expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.

2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a Software Update record for the PCM when using MDARS or IDS. MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. IDS Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealers expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.

following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.

For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service. Examples of residue or seepage that may not be considered a leak and that may not require repair based on splash shield inspection.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

Foreign debris on the blower motor after servicing the cabin air filter may be the cause. During the removal of the cabin air filter, foreign debris (leaves, dust, dirt....ect.) may fall on the blower motor causing a fluttering type noise or odor.

warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat in the coolant control valve on certain CX-5, Mazda3, CX-3, Mazda6 and CX-30 vehicles that are equipped with the suspected coolant control valve. The warranty coverage for a specific repair of fail-safe thermostat has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. Concern Outline:On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: Engine takes longer to warm up, Engine temperature gauge fluctuates, Low coolant temperature indicator (blue) light stays on longer or turns on while driving, Poor heater performance, especially at idle.This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair under this Special Service Program.

Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat in the coolant control valve on certain CX-5, Mazda3, CX-3, Mazda6 and CX-30 vehicles that are equipped with the suspected coolant control valve. The warranty coverage for a specific repair of fail-safe thermostat has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. Concern Outline:On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: Engine takes longer to warm up, Engine temperature gauge fluctuates, Low coolant temperature indicator (blue) light stays on longer or turns on while driving, Poor heater performance, especially at idle.This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair under this Special Service Program.

following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.

adhesion.

power consumption is restricted, thereby extending the transmitter battery life and the following will occur: The engine will not start unless the key transmitter is held over the Start Stop button. Outside door handle lock/unlock touch sensor is inoperative. Key transmitter indicator lights are inoperative. The following DTC's may be stored: DTC B13D3:94 (Communication error with remote transmitter) DTC P1260:00 (Immobilizer system problem).

power consumption is restricted, thereby extending the transmitter battery life. NOTE: Some customers may complain about an engine no start. This may be caused by the customer inadvertently putting the key transmitter in Power Saving Function.

specific repair of the fail-safe thermostat installed inside of the suspected coolant control valve on certain 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6 and 2020-2023 CX-30 vehicles. The warranty coverage for an applicable repair has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. If you are a recipient of this notice, your vehicle is included in this warranty extension program. What is the problem? On certain subject vehicles, the check engine light is illuminated with diagnostic trouble code (DTC) P0126, due to the fail-safe thermostat being stuck open. Additionally, you may notice one or more of the following symptoms: -Engine takes longer to warm up. -Engine temperature gauge fluctuates. -Low coolant temperature indicator (blue) light stays on longer or turns on while driving. -Poor heater performance, especially at idle. This warranty extension program applies only to the replacement of fail-safe thermostat of the vehicle exhibiting the concerns mentioned above. If the check engine light illumination is determined to be unrelated to the fail-safe thermostat being stuck open, the inspection and repair are not covered under this program.

CX-9, or 2018-2020 Mazda6 vehicle was equipped with a SKYACTIV-G 2.5T (Turbocharged) engine (Covered Vehicle). Mazda Motor Corporation has decided to conduct a Customer Service Program CSP (11) to inform you that Mazda is extending the limited powertrain warranty to provide necessary repairs free of charge if your Covered Vehicle has coolant leaks at the cylinder head around the exhaust manifold and to inform you that you may be eligible to receive reimbursement for past out-of-pocket expenses you previously incurred for such repairs on the terms and conditions as described below. Powertrain Warranty Extension: Mazda is extending the limited powertrain warranty to 10 years or 120,000-miles, whichever occurs first, to provide necessary repairs at no cost to you if your Covered Vehicle has coolant leaks at the cylinder head around the exhaust manifold. A dealer must inspect and confirm your Covered Vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for you to receive the repairs at no cost to you.

fail-safe thermostat being stuck open. Additionally, you may notice one or more of the following symptoms: -Engine takes longer to warm up. -Engine temperature gauge fluctuates. -Low coolant temperature indicator (blue) light stays on longer or turns on while driving. -Poor heater performance, especially at idle. This warranty extension program applies only to the replacement of fail-safe thermostat of the vehicle exhibiting the concerns mentioned above. If the check engine light illumination is determined to be unrelated to the fail-safe thermostat being stuck open, the inspection and repair are not covered under this program.

Mazda6 that are equipped with SKYACTIV-G 2.5T engine, the warranty coverage for specific repair of the coolant leak at cylinder head is extended to: 10 years (120 months) or 120,000 miles (192,000 km) whichever comes first, from the original warranty start date CONDITION OF CONCERN On certain subject vehicles, the coolant may leak at the cylinder head around the exhaust manifold.

There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold flange (2) on the cylinder head.

following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle.

specific repair of the fail-safe thermostat in the coolant control valve on certain CX-5, Mazda3, CX-3, Mazda6 and CX-30 vehicles that are equipped with the suspected coolant control valve. The warranty coverage for a specific repair of fail-safe thermostat has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. Concern Outline: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: Engine takes longer to warm up, Engine temperature gauge fluctuates, Low coolant temperature indicator (blue) light stays on longer or turns on while driving, Poor heater performance, especially at idle. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair under this Special Service Program.

specific repair of the fail-safe thermostat in the coolant control valve on certain CX-5, Mazda3, CX-3, Mazda6 and CX-30 vehicles that are equipped with the suspected coolant control valve. The warranty coverage for a specific repair of fail-safe thermostat has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. Concern Outline: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: Engine takes longer to warm up, Engine temperature gauge fluctuates, Low coolant temperature indicator (blue) light stays on longer or turns on while driving, Poor heater performance, especially at idle. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair under this Special Service Program.

Warranty Information is at the bottom of the TSB Parts and Warranty information and Repair Procedures will be available by October 25, 2024. Until that time if a vehicle is presented to your dealer with a complaint and CSP11 is visible in eMDCS, please click here and follow instructions in TSB 01-002/23 COOLANT LEAKS AT CYLINDER HEAD and hold claims until the Parts and Warranty Information is available in eMDCS and MGSS.

warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.

warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.

warranty to 10 years or 120,000 miles, whichever occurs first, for necessary repairs if the covered vehicle has coolant leaks at the cylinder head, around the exhaust manifold. A dealer must inspect and confirm the covered vehicle is exhibiting coolant leaks at the cylinder head around the exhaust manifold matching Technical Service Bulletin 01-002/23 (Feb. 10, 2023) for the repair to be covered.

Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. Hotline and MASH authorization is not required to order parts for performing this repair. If there are any questions on part ordering or part status, contact the Dealer Assistance Group.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle.

this causes the battery to be completely discharged and not rechargeable. This is caused by a deterioration in the seat ventilation control unit. To eliminate this concern, the material for the circuit of the seat ventilation control unit has been modified.

Mazda has introduced a replacement kit of the thermostat located within the Coolant Control Valve (CCV). NOTE: It is no longer necessary to replace the CCV for this DTC.

adhesion.

following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.

following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.

following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.

This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.

Contamination in the engine oil may cause the engine oil solenoid valve to become stuck, resulting in improper operation of the oil pump and improper oil pressure.

A steering column nut loosens due to excessive load when driving on irregular roads. To eliminate this concern, the tightening torque for the steering column nut has been increased.

following symptoms: The engine takes longer to warm up The engine temperature gauge fluctuates The low coolant temperature indicator (blue) light stays on longer or comes on while driving Poor heater performance, especially at idle

This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. Dealers can now utilize the Limited Parts Ordering (LPO) page on eMDCS to order the repair parts for 2.5L (with cylinder deactivation) and 2.5L turbo cylinder head repairs. Hotline and MASH authorization is not required to order parts for performing this repair. If there are any questions on part ordering or part status, contact the DAG group for assistance.

Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. Dealers can now utilize the Limited Parts Ordering (LPO) page on eMDCS to order the repair parts for 2.5L (with cylinder deactivation) and 2.5L turbo cylinder head repairs. Hotline and MASH authorization is not required to order parts for performing this repair. If there are any questions on part ordering or part status, contact the DAG group for assistance.

This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).

adhesion.

this causes the battery to be completely discharged and not rechargeable. This is caused by a deterioration in the seat ventilation control unit. To eliminate this concern, the material for the circuit of the seat ventilation control unit has been modified.

following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose according to the instructions on MGSS online. Due to production variety of the failsafe thermostat integrated in the coolant control valve, engine coolant may enter into a dry hollow in the failsafe thermostat, resulting in unintended opening of the failsafe thermostat at lower temperatures (104-176 F (40-80 C)). To eliminate this concern, the production process of the coolant control valve has been modified.

Contamination in the engine oil may cause the engine oil solenoid valve to become stuck, resulting in improper operation of the oil pump and improper oil pressure. DTC P0524:00 (Engine oil pressure too low), DTC P055F:00 (Engine oil pressure malfunction). The control software of the PCM has been modified to eliminate this concern. In addition, the production process has been modified to reduce contamination in the engine oil solenoid valve, oil pump, spacer and oil filter.

There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold flange (2) on the cylinder head.

P0302:00, P0303:00, P0304:00.NOTE: Only turbo engines are applicable; non-turbo engines are NOT applicable. In most cases, DTCs P030X stores, but sometimes not. Sometimes the CHECK ENGINE light does not recognize this engine concern. This is caused by the variable valve in the exhaust manifold seizing and causing the exhaust port to become hot and the exhaust valve seat to wear unevenly, resulting in compression leakage. To eliminate this concern, the design of the exhaust manifold has been modified.

There may be cracks at the stud bolt hole or at the outside of the exhaust manifold. Cracks may be caused by: - Deformation of the exhaust manifold during usage causing unexpected force to certain areas of the cylinder head. - Residual stress generated during production in the cylinder head material may be greater than expected. The external force from the exhaust system when driving over bumps may cause unexpected force to certain areas of the cylinder head. To eliminate this concern, the design of the exhaust manifold gasket and the cylinder head has been modified to reduce the force on the cylinder head.

(only turbo engines are applicable; non-turbo engines are NOT applicable). - In most cases, P030X is stored, but sometimes not. - Sometimes the CHECK ENGINE light does not recognize this engine concern. This is caused by the variable valve in the exhaust manifold seizing and causing the exhaust port to become hot and the exhaust valve seat to wear unevenly, resulting in compression leakage. To eliminate this concern, the design of the exhaust manifold has been modified.

These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.

Vehicles having this concern should use the following Inspection/Repair procedure.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location)

following symptoms: * The engine takes longer to warm up * The engine temperature gauge fluctuates * The low coolant temperature indicator (blue) light stays on longer or comes on while driving * Poor heater performance, especially at idle NOTE: * Vehicles with SKYACTIV-G 2.5T are not applicable. * If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies, this information is not applicable. Diagnose according to the instructions in MGSS. Due to production variety of the failsafe thermostat integrated in the coolant control valve, engine coolant may enter into a dry hollow in the failsafe thermostat, resulting in unintended opening of the failsafe thermostat at lower temperatures (104-176 F (40-80 C)). To eliminate this concern, the production process of the coolant control valve has been modified.

control valve is closed and air in the engine cannot escape during ignition ON. Therefore, turn the ignition OFF when refilling engine coolant using the radiator filler neck.

this causes the battery to be completely discharged and not rechargeable. This is caused by a deterioration in the seat ventilation control unit. To eliminate this concern, the material for the circuit of the seat ventilation control unit has been modified.

fast idle to normal idle speed during cold start. This is caused by a variable valve being stuck in the closed position. When returning from fast idle to normal, the stuck valve suddenly opens due to thermal change around it which causes abnormal noise. To eliminate this concern, the internal design of the exhaust manifold has been modified.

this causes the battery to be completely discharged and not rechargeable. This is caused by a deterioration in the seat ventilation control unit. To eliminate this concern, the material for the circuit of the seat ventilation control unit has been modified.

There may be cracks at the stud bolt hole or at the outside of the exhaust manifold. Cracks may be caused by: - Deformation of the exhaust manifold during usage causing unexpected force to certain areas of the cylinder head. - Residual stress generated during production in the cylinder head material may be greater than expected. The external force from the exhaust system when driving over bumps may cause unexpected force to certain areas of the cylinder head. To eliminate this concern, the design of the exhaust manifold gasket and the cylinder head has been modified to reduce the force on the cylinder head.

been produced with a combination of Type A timing chain with 2 yellow-colored links with a Type B crankshaft sprocket.

Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly.

SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly.

The door lock/unlock operation will not work using the remote transmitter button. 2. The door lock/unlock operation will not work using the door lock/release touch sensor. 3. The engine will not start using the ignition switch. 4. The transmitter operates by itself. 5. The key battery drains faster than usual. Symptoms 1-3: This may be caused when excess load is applied to the remote transmitter, deforming the electrical terminals and creating poor contact with the battery. To eliminate this concern, the structure in the remote transmitter has been modified to reduce the deformation of the electrical terminals. Symptom 4-5: This may be caused when excessive load is applied to the remote transmitter, creating a gap around the gasket where moisture enters and corrodes the circuit board which in turn drains the key battery faster than usual. To eliminate this concern, the thickness of the case wall on the gasket mounting surface has been increased and the bonding strength of the components has been improved to prevent deformation. Customers having this concern should have their vehicle repaired using the following repair procedure.

There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2).

Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. Dealers can now utilize the Limited Parts Ordering (LPO) page on eMDCS to order the repair parts for 2.5L (with cylinder deactivation) and 2.5L turbo cylinder head repairs. There is no longer a need to contact hotline for part ordering. If there are any questions on part ordering or part status, contact the DAG group for assistance.

Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly.

There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2). Cracks may be caused by: Deformation of the exhaust manifold during usage causing unexpected force to certain areas of the cylinder head. Residual stress generated during production in the cylinder head material may be greater than expected. The external force from the exhaust system when driving over bumps may cause unexpected force to certain areas of the cylinder head. To eliminate this concern, the design of the exhaust manifold gasket and the cylinder head has been modified to reduce the force on the cylinder head.

malfunction) stored, the cylinder deactivation oil control valve may be plugged with plastic debris from the oil filter wrapper. The debris may enter the center of the oil filter when poking a hole in the filter wrapper during removal, and then travel through the engine and plug the cylinder deactivation oil control valve.

Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline, E85: A blend of 85% ethanol and 15% gasoline, All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V. What if a customer puts E85 in there Mazda vehicle? Symptoms include: Rough Running, Lean Codes, Misfires and/or misfire codes, Lack of power, Poor fuel economy, Spark knock, Mechanical engine damage.

This is caused by burrs that were not trimmed completely in the manufacturing process of the blower motor. To eliminate this concern, the manufacturing process of the blower motor has been modified to efficiently trim burrs.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on, P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on, P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on, P0780:00 - Gear shifting malfunction, P1738:00 Automatic transaxle internal malfunction. This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.

following symptoms: The engine takes longer to warm up, The engine temperature gauge fluctuates, The low coolant temperature indicator (blue) light stays on longer or comes on while driving, Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable. Due to production variety of the failsafe thermostat integrated in the coolant control valve, engine coolant may enter into a dry hollow in the failsafe thermostat, resulting in unintended opening of the failsafe thermostat at lower temperatures (104-176 F (40-80 C)). To eliminate this concern, the production process of the coolant control valve has been modified.

Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly.

The door lock/unlock operation will not work using the door lock/release touch sensor. The engine will not start using the ignition switch. This is caused when excess load is applied to the remote transmitter and the electrical terminals in it may be deformed, causing poor contact with the battery. To eliminate this concern, the structure in the remote transmitter has been modified to reduce the deformation of the electrical terminals.

Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. DUE TO A SUPPLY ISSUE FOR CYLINDER HEADS, GASKET SETS, AND PARTIAL ENGINE, PLEASE CONTACT HOTLINE FOR REPAIR GUIDANCE.

This may be caused by a customer installed aftermarket decorative trim and/or cover on the START/STOP ENGINE button. The aftermarket accessory may create electrical interference, which may interfere with programming.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

Contamination in the engine oil may cause the engine oil solenoid valve to become stuck, resulting in improper operation of the oil pump and improper oil pressure. DTC P0524:00 (Engine oil pressure too low), DTC P055F:00 (Engine oil pressure malfunction). The control software of the PCM has been modified to eliminate this concern. In addition, the production process has been modified to reduce contamination in the engine oil solenoid valve, oil pump, spacer and oil filter.

The tapping noise may be caused by the switchable hydraulic lash adjuster (HLA), which may not work properly due to air bubbles accumulated in the oil passage in it. To eliminate this concern, the switchable HLA has been modified for increased oil supply to reduce air bubbles in the oil passage. NOTE: The switchable HLA can be pressed down with a finger if air bubbles have accumulated in it.

following symptoms: The engine takes longer to warm up, The engine temperature gauge fluctuates, The low coolant temperature indicator (blue) light stays on longer or comes on while driving, Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable. Due to production variety of the failsafe thermostat integrated in the coolant control valve, engine coolant may enter into a dry hollow in the failsafe thermostat, resulting in unintended opening of the failsafe thermostat at lower temperatures (104-176 F (40-80 C)). To eliminate this concern, the production process of the coolant control valve has been modified.

COOLANT TEMPERATURE (BLUE) LIGHT ON: Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle.

after being left on when turning off the engine. The logic has changed from previous Mazdas where the seat warmers and seat ventilation automatically turned on when the engine was restarted.

P2610:00: Instrument cluster internal engine off timer performance problem. P2507:00: PCM battery voltage low input

The tapping noise may be caused by the switchable hydraulic lash adjuster (HLA), which may not work properly due to air bubbles accumulated in the oil passage in it.

Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. NOTE: Cylinder head replacement requires MASH authorization.

following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle.

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? Yes - No repair is necessary. No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE).

The tapping noise may be caused by the switchable hydraulic lash adjuster (HLA), which may not work properly due to air bubbles accumulated in the oil passage in it.

head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H

U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. For Mazda6 and CX-5, the following error messages may appear in the instrument cluster. Front camera sensor system malfunction Forward Smart City Brake Support Malfunction Driver attention alert system malfunction. This may be caused by the battery voltage falling and the EPS control module failing the initial learning for the steering center position while cranking. The FSC detects the error notified by the EPS control module. To correct this concern, the control software of the EPS control module has been modified while the repair procedure modifies the FSC for earlier repairs in the market.

malfunction) stored, the cylinder deactivation oil control valve may be plugged with plastic debris from the oil filter wrapper. The debris may enter the center of the oil filter when poking a hole in the filter wrapper during removal, and then travel through the engine and plug the cylinder deactivation oil control valve.

DTC U0420:68 [Forward sensing camera (FSC)]: Error signal received from electric power steering (EPS) control module. For Mazda6 and CX-5, the following error messages may appear in the instrument cluster. Front camera sensor system malfunction Forward Smart City Brake Support Malfunction Driver attention alert system malfunction. This may be caused by the battery voltage falling and the EPS control module failing the initial learning for the steering center position while cranking. The FSC detects the error notified by the EPS control module. To correct this concern, the control software of the EPS control module has been modified while the repair procedure modifies the FSC for earlier repairs in the market.

Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. NOTE: Cylinder head replacement requires MASH authorization.

are 597 vehicles contained in this DRW, and all had a paid Pre-Delivery Inspection performed at the port and were to be used as fleet vehicles. These vehicles have since been reallocated to dealerships and due to significant idle time prior to arriving at dealers, the vehicle should have a new Pre-Delivery Inspection performed in order to support a perfect delivery to the customer.

Valves, valve springs, valve spring seats and cotters (IN/EX) are included in the new assembly.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

P2229:00 (BARO sensor circuit high input). This concern will most likely occur on vehicles that have aftermarket wax applied in the engine compartment. Aftermarket wax applied in the engine compartment may adhere on the breather hole located at the bottom of the PCM, which may collect dust and result in a plugged filter. This breather hole is actually a filter for the air pressure sensor in the PCM. When the PCM gets hot, the internal air pressure may rise due to the plugged filter and result in DTC P2229:00. To eliminate this concern, the shape of the PCM bracket has been modified to not cover the breather hole and eliminate a gap between it and the PCM that may promote the residual liquid wax.

power consumption is restricted, thereby extending the transmitter battery life. IMPORTANT: The engine will not start unless the key transmitter is held over the Start Stop button. Outside door handle lock/unlock touch sensor is inoperative. Key transmitter indicator lights are inoperative.The key transmitter control functions (i.e. locking/unlocking door, etc.) are operational when pressing the transmitter switches, even while the key power saving function is turned ON.

The tapping noise may be caused by the switchable hydraulic lash adjuster (HLA), which may not work properly due to air bubbles accumulated in the oil passage in it.

following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle.

following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle.

after being left on when turning off the engine. The logic has changed from previous Mazdas where the seat warmers and seat ventilation automatically turned on when the engine was restarted. NOTE: Customers in cold weather are more likely to complain about this if their vehicle is equipped with Mazda Mobile Start (MMS) (not available on Mazda3 or CX-30) because the MMS accessory instructions state the seat warmers WILL turn on when the engine is restarted. The same can happen in the hotter weather with the seat ventilation. This information is incorrect for these vehicles. Both features will now require a manual setting every time the vehicles are restarted after being turned off. Consult the vehicles owners manual for more details on proper seat warmer/seat ventilation operation.

P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display F0-002 during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km).Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear Parking Sensors - Rear Seat Entertainment - Smartphone Screen Mirroring - Bumper Trim/Guards - Door Mirror Caps - Fog Lights - Moonroof Wind Deflector - Roof Rack - Side Window Deflectors - Splash Guards - Trailer Hitch - Thule Products - Wheels Locks - Aero Kit - Air Dam - Rear Spoiler - Tunnel Under Bars - Lower Arm Bar - Side Sill Extensions - Arm Rest - Illuminated Door sill Trim Plates - Interior Lighting

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.

Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.

overnight) or after it has been idling for an extended time. The tapping noise will decreases as the vehicle is being driven or if the rpm is held above 2500-3000 RPM. This may be caused by the valve Hydraulic Lifters (HLA) bleeding down as the engine cools or when the engine has been idling for an extended period of time, creating excessive valve lash clearance.

Engine Start/Start Button Amber indicator light flashing Battery discharge Electrical relay buzzing noise DTC B13D3:94 (Communication error with remote transmitter) stored.This may be caused by: A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehicless wiring harness may create unusual electrical symptoms.

DTC P2096:00 - Air fuel too lean. NOTE: This concern occurs only on vehicles with PCMs manufactured by MITSUBISHI. Due to improper control logic of the PCM, a false error may be detected. To eliminate this concern, the PCM software has been modified.

There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. Wrinkles may not be completely removed after the repair is completed. Leather is a natural material and may develop some wrinkles due to aging and wear during normal useage.

seat back surface.

seat back surface.

seat back surface.

A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method

Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. The accumulated coolant is solidified and plugs the gap in high temperature environment and the seepage is stopped and does not progress. This is normal and does not require a part replacement, clean off the dried coolant from around the pipe with a wire brush.

Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

This is caused by the seat back decoration plate not being strong enough. To eliminate this concern, the seatback decoration plates have been modified.

The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section once a part is selected. Accessories E-catalog For models prior to 2016: Accessory Parts and Installation Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method A. Auxiliary Key Trace Cut Method If only one auxiliary key is lost/missing, some key cutting machines can trace cut a new key blank. 1. Trace cut the new auxiliary key blank(s). B. Auxiliary Key Code Cut Method If both auxiliary keys are lost/missing, use this method for cutting new auxiliary key blank(s). 1. Confirm you have access to a Mazda approved key cutting machine. See Mazda Approved Key Cutting Machine table.

A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.

https://ecatalog.mazdausa.com

style remote transmitter as they use a different key code than the previous transmitter key. Follow the repair procedure if one or both auxiliary keys are lost:

Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.

different key code than the previous transmitter key. Follow the repair procedure if one or both auxiliary keys are lost:

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a batterys Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission

lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.

lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.

lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced since December 2021 at the supplier.

This is caused by a failure in the ambient temperature sensor. To correct this issue, the ambient temperature sensor has been modified.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a good know terminal.To measure the voltage/resistance avoiding any terminal damage.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc.) placed on the front passenger's seat.

data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage.

power consumption is restricted, thereby extending the transmitter battery life.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all auxiliary keys are lost.

The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.

data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage.

The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.

This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all auxiliary keys are lost.

The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.

This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all auxiliary keys are lost.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

function grayed out SiriusXM stops playing No sound from SiriusXM but other sources work SiriusXM system recovers after ignition OFF-ON. Do not perform any repairs at this time. Mazda is aware of the concerns and is working on a repair. This service information will be updated when a repair is available. NOTE: An interim solution is available for the SiriusXM concerns.

If it is mistakenly replaced with the conventional CR2025 used in the previous type remote transmitter, it may cause a malfunction. Verify the button cell battery type before replacing it.

Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with an active SAT radio.

on the front window and/or display.

on the front window and/or display.

Peeling, spider cracks and white dots.

screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.

screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.

It includes new display repair kit part numbers for the 2018-2019 Mazda2, 2018-2020 CX-3 and 2018-2020 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White dots

There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Please use the table below when ordering the screen repair kits. This can also be found in Service Alert SA-041/22.

Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] * B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] * No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. * In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). * In other cases this DTC might be found without a related customer concern. NOTE: In most cases, no dealer visit is necessary.

Spider Cracks - Surface Peeling - White dots

Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

Surface Peeling - Spider Cracks Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.

Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.

No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. 6 Bluetooth device will not pair No. 7 Incorrect GPS position No. 8 Voice Recognition Does Not Work No. 9 Cannot Make a Hands-Free Call No. 10 Cannot Play Bluetooth Audio No. 11 Other Symptoms No. 12 How to update the Navigation SD Card Map No. 13 How to Check Navi SD Card VIN Lock

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.230 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software. Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

This may be caused by an incorrect clock GPS Sync setting.

All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.

All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.

/ Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions

Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles], B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles build on or before March 2, 2019], No DTC - Gen 7 vehicles built after March 2, 2019, DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

/ Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.

CarPlay / Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS - Infotainment - MAZDA CONNECT Updates - Apple Carplay / Android Auto MDARS Activation Instructions

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update.

This may be caused by an incorrect clock GPS Sync setting.

of view B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.

Both of these services provide information in the U.S. & Canada. NOTE: SiriusXM Traffic Plus and Travel Link subscription is free of charge for 3 years only if equipped with factory installed navigation system. NOTE: 2019-2020 Mazda3 and 2020 CX-30 are not equipped with factory installed navigation system,however, it is available as a dealer installed accessory. SiriusXM Traffic Plus and Travel Link are available on the 2019-2020 Mazda3 and 2020 CX-30 Preferred Package and above, as a paid subscription. Traffic Plus feature requires in-vehicle navigation SD card. SiriusXM Satellite Radio trial subscription is free of charge for 3 months.

Audio System, Bluetooth, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux Voice Command, How to Check Navi SD Card VIN Lock.

Use the troubleshooting chart below to repair the vehicle.

The subject vehicles were parked outside when Typhoon No.17 passed through Hiroshima and Hofu, Japan, and might have been exposed to misty seawater caused by a heavy wind. The sampling inspection revealed that the chrome plated window moldings of certain vehicles became rusty due to seawater mist. All of the potentially affected vehicles have been rinsed with fresh water prior to shipment. OUTLINE OF REPAIR: If the vehicle has a port hangtag with direction to repair a chrome molding, but does not show DRW27 in eMDCS Warranty Vehicle Inquiry, please contact Dealer Recall Help on MXConnect > Warranty. Look for a hangtag placed in the vehicle by the port. If one is found and the vehicle displays DRW27 in eMDCS, inspect the affected molding(s) and perform a secondary cleaning with polishing compound. If any rust or pitting is still present, replace that affected molding(s) with new parts(s).

This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.

The rearview mirror (1) rattles up and down (2) while adjusting the mirror. 2. The rearview mirror (1) makes a rattle noise depending on the road surface conditions while driving. This concern is caused during rearview mirror installation. The adhesive is squeezed out between the windshield and the mirror base. The rearview mirror is assembled on top of the overextended adhesive. The adhesive is softened by heat, and loosening screws, results in a rattling concern.

This may be caused by the sun's reflection.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

remedy, and warranty coverage (if applicable).

This may be caused by the sun's reflection.

This may be caused by the sun's reflection.

This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by: 1. The electric fold-in unit inside the outer mirror may be damaged by corrosion from water entry due to insufficient water tightness. 2. The electric fold-in unit may interfere with the outer mirror frame due to improper installation of the electric fold-in unit. 3. The friction around the shaft of the folding mechanism may increase.

remedy, and warranty coverage (if applicable).

This may be caused by: 1. The electric fold-in unit inside the outer mirror may be damaged by corrosion from water entry due to insufficient water tightness. 2. The electric fold-in unit may interfere with the outer mirror frame due to improper installation of the electric fold-in unit. 3. The friction around the shaft of the folding mechanism may increase. To eliminate this concern, the following changes have been implemented: 1. The overlapping part of the water-proof sealing inside the electric fold-in unit (it cannot be seen from the outside) has been extended and the flange (1) has been attached instead of a water proof seal. 2. The height of the mirror frame rib has been changed. 3. The material of the washer has been changed and another washer has been added to the shaft.

This may be caused by the sun's reflection.

This may be caused by: 1. The electric fold-in unit inside the outer mirror may be damaged by corrosion from water entry due to insufficient water tightness. 2. The electric fold-in unit may interfere with the outer mirror frame due to improper installation of the electric fold-in unit. 3. The friction around the shaft of the folding mechanism may increase To eliminate this concern, the following changes have been implemented: 1. The overlapping part of the water-proof sealing inside the electric fold-in unit (it cannot be seen from the outside) has been extended and the flange (1) has been attached instead of a water proof seal. 2. The height of the mirror frame rib has been changed. 3. The material of the washer has been changed and another washer has been added to the shaft

This is caused by the gap between the roof molding attachment clips and the roof panel not being wide enough to allow paint to be appropriately applied to the roof panel. To eliminate this concern, the shape of the roof molding clip has been changed to enable paint application between the clip's rib and roof during the manufacturing process.

This may be caused by the sun's reflection.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.

This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier.

remedy, and warranty coverage (if applicable).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

remedy, and warranty coverage (if applicable).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise. To eliminate this concern, the brake pad material has been changed in order to improve the rust-removing capability.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: - The windshield is dirty - The FSC lens is foggy - There is low visibility due to rain, fog or snow - It is at night and there is not enough light - There is direct or reflected sunlight on the FSC - There is problem with the FSC * There is a problem with the AUTOHOLD control function. * There is a problem with the electric parking brake (EPB).

This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.

This is caused by a brake torque variation due to an uneven coating of the brake pad friction material forming on the surface of the disc plate. To eliminate this concern, the surface processing on the disc plate has been changed.

This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.

This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise. To eliminate this concern, the brake pad material has been changed in order to improve the rust-removing capability.

This is caused by a brake torque variation due to an uneven coating of the brake pad friction material forming on the surface of the disc plate. To eliminate this concern, the surface processing on the disc plate has been changed.

cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: The windshield is dirty The FSC lens is foggy There is low visibility due to rain, fog or snow It is at night and there is not enough light There is direct or reflected sunlight on the FSC There is problem with the FSC There is a problem with the AUTOHOLD control function. There is a problem with the electric parking brake (EPB).

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

This may be caused by a brake torque variation at that speed due to an inappropriate machining process of the brake disc surface. Customers having this concern should have their vehicle repaired using the following repair procedure.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

This may be caused by a brake torque variation at that speed due to an inappropriate machining process of the brake disc surface.

essential to first classify the issue into one of three primary categories: Noise, Vibration, or Harshness. Many customer complaints may involve overlapping symptoms, such as both noise and vibration, so identifying the dominant characteristic is critical. Once the primary symptom is determined, follow the appropriate diagnostic path. For example, if a concern includes both noise and vibration but is related to vehicle speed, the vibration diagnostic path should be followed. When considering component replacement during the diagnostic process, it is best practice to start with the lowest cost or most accessible part unless diagnostic evidence clearly identifies a more expensive or complex component as the root cause. This approach helps minimize repair costs and avoids unnecessary part replacements. For example, a growling or bearing whine noise may be mistakenly attributed to internal components in the differential, transfer unit, or transmission, when the actual source is a wheel bearing. Misdiagnosis like this can lead to unnecessary repairs, added time and cost. To help prevent this, always follow the guidelines in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.

Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.

This may be caused by the automatic transaxle fluid (ATF) being contaminated by iron powder due to excessive wearing of the lock up clutch in the torque converter.

This may be caused by the automatic transaxle fluid (ATF) being contaminated by iron powder due to excessive wearing of the lock up clutch in the torque converter.

The symptom can be temporarily repaired by A/T initial learning procedure, but may recur after multiple driving cycles.

The system performance has been improved as follows: Ver. 74.00.324 fixes these software errors (bugs): * If the shift lever is operated quickly while displaying the CarPlayTM screen, the rear view screen may not return to the CarPlayTM screen. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into the R position.

Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

configuration.

The symptom can be temporarily repaired by A/T initial learning procedure, but may recur after multiple driving cycles. Applicable situations: *Shifting up: 2-3, (4-5) *Shifting down: 4-3, (6-5) NOTE: (4-5) and (6-5) are felt more than others due to the gear ratio. *Shifting into R: D-R, N-R, P-R Improper control logic of the TCM may cause improper learning of R-3-5 brake engaging speed during certain driving situations. To correct this concern, the control logic of the TCM has been modified.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Use a clean towel damped in leather/vinyl cleaner or mild soap to clean the steering wheel. NOTE: Upholstery maintenance and care information can also be found in the Owner's Manual.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order to re-install the original plug from the old transmission.

The symptom can be temporarily repaired by A/T initial learning procedure, but may recur after multiple driving cycles. Applicable situations: Shifting up: 2-3, (4-5) Shifting down: 4-3, (6-5) NOTE:(4-5) and (6-5) are felt more than others due to the gear ratio. Shifting into R: D-R, N-R, P-R. Improper control logic of the TCM may cause improper learning of R-3-5 brake engaging speed during certain driving situations. To correct this concern, the control logic of the TCM has been modified.

NOTE: The following Caution is included with every ATX that requires configuration.

Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the oil cooler was missing altogether. IMPORTANT NOTE: ALWAYS REMEMBER TO INCLUDE THE ORIGINAL OIL COOLER WITH THE RETURNED TRANSMISSION CORE!

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface.

This may be caused by light glare on the SST.

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.

This is caused by the edge of the lens support part interfering with the inner lens of the headlight under a strong vibration during driving, scratching the inside of the inner lens. As a result, the resin powder adheres to the inside of the headlight lens. To eliminate this concern, the support rib location of the inner lens has been changed to prevent the interference.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

If B61L-67-XCX* appears in the GEPC search, the VIN is applicable for this repair only if the part has been previously replaced with KDD1-67-XCX. Some vehicles may exhibit the master warning light (and other warning lights) illuminated while driving, with DTC B115E:76 stored in memory.

This may be caused by light glare on the SST.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Use the information below to troubleshoot the customers complaint: MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE CANNOT COMMUNICATE WITH VEHICLE ERROR MESSAGE INSTALLED ON ANDROID DEVICES COMMUNICATION ERRORS MMS CHECK MODE - Use to verify system operation (see below).

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

A steering column nut loosens due to excessive load when driving on irregular roads. To eliminate this concern, the tightening torque for the steering column nut has been increased.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

Customers having this concern should have their vehicle repaired using the following repair procedure.

be wet.

be wet.

be wet.

74.00.311 or later).

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.352 or later).

Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. E85: A blend of 85% ethanol and 15% gasoline All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V.

Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).

The following are possible causes of floor mat interference, which can be avoided with proper usage.

However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts. CAUTION: Be aware that when cleaning the brand emblem, never use cleaning products that are highly acidic/alkaline detergent, organic solvents or those with aggressive chemical products, otherwise, the brand emblem may become cracked and/or deformed (as shown in the example below). Always refer customers to the owners manual for proper cleaning using cold or lukewarm water and a mild, neutral detergent.

The noise is most noticeable when duplicating the driving conditions of going up or down an incline while simultaneously making a turn. NOTE: For Mazda6 vehicles, the noise may only be heard once per day. To reproduce the concern, allow the vehicle to sit overnight and then drive it. The noise has been traced to the front stabilizer (sway bar) bushings and the recommended action is the following repair information (if the noise can be duplicated). NOTE: The repair itself is not complex, but accurately replicating the concern may require additional time. To minimize inconvenience to the customer, ensure that they are provided with a loaner vehicle while the diagnosis and repair take place.

This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.