2017 Mazda Mazda5 TSBs

Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

When you encounter a customer with this concern, first verify the condition when the customer noticed this symptom. If the condition is similar to the following "CONTROL LOGIC OF AMBIENT TEMPERATURE" or "DIFFERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS", advise the customer that this is a normal characteristic of the vehicle and not a malfunction. If the condition does not meet the following and the sensor malfunction is suspected, make sure to inspect the sensor according to MGSSonline or Workshop Manual (section 09-22 AMBIENT TEMPERATURE SENSOR INSPECTION). Replace the sensor only when it fails the Workshop Manual inspection.

This may be caused by the sun's reflection.

This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.

remedy, and warranty coverage (if applicable).

This concern only occurs on vehicles where the liftgate stay damper recall (9916H) was previously performed. Some of the liftgate stay damper rods used for the recall were chrome-plated, which is smooth and may cause a shortage of oil film to the stay damper rod. The squeak noise occurs due to the friction between the gas sealing and the damper rod when opening and/or closing the liftgate.

on MS3 under the "IDs/Infotainment" tab.

Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature.

for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active (working SAT radio).

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

The following are possible causes of floor mat interference, which can be avoided with proper usage.

balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?