2012 Mazda Mazda3 TSBs

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

Foreign debris on the blower motor after servicing the cabin air filter may be the cause. During the removal of the cabin air filter, foreign debris (leaves, dust, dirt....ect.) may fall on the blower motor causing a fluttering type noise or odor.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).

These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.

Vehicles having this concern should use the following Inspection/Repair procedure.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location)

Stored in TCM Memory

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:

Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline, E85: A blend of 85% ethanol and 15% gasoline, All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V. What if a customer puts E85 in there Mazda vehicle? Symptoms include: Rough Running, Lean Codes, Misfires and/or misfire codes, Lack of power, Poor fuel economy, Spark knock, Mechanical engine damage.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on, P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on, P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on, P0780:00 - Gear shifting malfunction, P1738:00 Automatic transaxle internal malfunction. This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.

This may be caused by a customer installed aftermarket decorative trim and/or cover on the START/STOP ENGINE button. The aftermarket accessory may create electrical interference, which may interfere with programming.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

P0015:00 - Exhaust CMP timing over-retarded, P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? Yes - No repair is necessary. No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE).

head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H

This noise is a normal engine operation for improved exhaust gas emissions. The noise does not indicate a malfunction. ACCELERATED WARM-UP SYSTEM (AWS): All SKYACTIV-G engines adopt AWS to reduce exhaust gas emissions immediately after a cold engine start. AWS increases the engine idling speed and retards the ignition timing for about 20 seconds after the cold engine start to quickly warm up the catalytic converter. The customer may identify the engine sound during the AWS operation as a unusual noise.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.

Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.

P0300:00: Random misfire detected, P0301:00: Cylinder No.1 misfire detected, P0302:00: Cylinder No.2 misfire detected, P0303:00: Cylinder No.3 misfire detected, P0304:00: Cylinder No.4 misfire detected. Carbon may be deposited around the intake valves, resulting in unstable engine combustion and misfiring during the accelerated warm-up system (AWS) operation.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 - Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial checkis a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.

P0456: EVAP system leak detected (very small leak). The concern is most likely the result of the customer not getting the fuel cap completely closed after fueling the vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.

The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.

refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system. When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur to oxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

(e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely closed after fuelingthe vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/Cevaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers. This treatment provides a durable coating that will aid to prevent biological reactions that lead to odorconcerns. It is applied to the evaporator in a misted form that is introduced by way of the cabin air filter, the re-circulate door, the blower motor resistor access, or the blower motor air intake. Proper application requires the evaporator surface to be: Relatively clean and free of leaves, dust build-up and debris. Thoroughly dried, and the product cured onto it after application. NOTE: Keep the cooling unit dry by leaving the blower fan ON (at least on low), even if the A/C is not being used. In low humidity (dry) conditions, keep the ventilation system in the "FRESH" mode all the time, or as much as possible. In high humidity conditions, or if the air has a lot of dust or pollen, keep the system in the "RECIRCULATION" mode. A few minutes before reaching a destination, turn the A/C OFF, but leave the blower fan ON. This stops the accumulation of condensation on the evaporator/cooling unit, and it helps dry the inside of the cooling unit. A/C odor is not unique to Mazda vehicles as it will occur in other makes and models. To minimize A/C odor, suggest the following to the customers.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to MGSS online for proper diagnosis and repair procedure.

This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial check is a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.

P0015:00 - Exhaust CMP timing over-retarded P0524:00 - Engine oil pressure too low This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.

The unique oil filter can be identified with two white bands as shown below.

Vehicles having this concern should use the following Inspection/Repair procedure.

In order to do this, MNAO is collecting inflators for evaluation in certain zones. For 2003-2008 Mazda6 (including Mazdaspeed6) and 2004-2011 RX-8: Collect 30 Driver-side and 30 Pas-senger-side inflators (60 total) from vehicles that have completed Recall 8215F for Driver-side and Recall 9416E for Passenger-side airbags in the following zones. For 2010-2013 Mazda3: Collect 200 Passenger-side inflators from vehicles in the following zones.

P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the ?SpeedometerReplacement Label?.Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda?s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.With the use of SPECMO?s services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

Mazda3 vehicles produced from May 6, 2010 through July 19, 2013. The warranty coverage for instrument panel replacement due to warping or a gap is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date or April 30, 2018 whichever is later, with no mileage limitation. On certain 2010-2013 Mazda3 vehicles, the instrument panel just above the information display may be warping, generating a gap between the instrument panel and information display, if exposed to heat under high ambient temperature.

Mazda3 vehicles produced from May 6, 2010 through July 19, 2013. The warranty coverage for instrument panel replacement due to warping or a gap is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date or April 30, 2018 whichever is later, with no mileage limitation. On certain 2010-2013 Mazda3 vehicles, the instrument panel just above the information display may be warping, generating a gap between the instrument panel and information display, if exposed to heat under high ambient temperature.

Mazda3 vehicles produced from May 6, 2010 through July 19, 2013. The warranty coverage for instrument panel replacement due to warping or a gap is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date or April 30, 2018 whichever is later, with no mileage limitation. On certain 2010-2013 Mazda3 vehicles, the instrument panel just above the information display may be warping, generating a gap between the instrument panel and information display, if exposed to heat under high ambient temperature.

and/or P061B and/or driveability problem after reprogramming the PCM using IDS versions 105.02 to 105.04. If the PCM is reprogrammed with any software number included in the attached file and the throttle valve has too much carbon build up, the engine air amount calculation by the problem software may not be accurate. Perform the following Repair Procedure to correct this issue. NOTE Current version of IDS is 106.02.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION P1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.

THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES.

P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

INCREASE WITH ENGINE SPEED THE ATX DOES NOT SHIFT UP OR DOWN AS EXPECTED THE CONDITION MAY NOT ALWAYS BE ABLE TO BE REPRODUCED AND DTCS MAY NOT BE STORED WHEN THE VEHICLE IS BROUGHT IN. FOREIGN MATERIAL (IRON PARTICLES IN THE ATF) MAY ENTER THE ATX VALVE BODY AND CAUSE A TEMPORARY MALFUNCTION OF THE VALVE BODY AND/OR SENSOR (ATX FAIL-SAFE FUNCTION ACTIVATED). THE FAIL-SAFE FUNCTION IS CANCELED WITHOUT DTCS RECORDED IF THE MALFUNCTION GOES AWAY AND DOES NOT OCCUR AGAIN AT THE NEXT DRIVE CYCLE.

P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED CARBON MAY BE DEPOSITED AROUND THE INTAKE VALVES, RESULTING IN UNSTABLE ENGINE COMBUSTION AND MISFIRING DURING THE ACCELERATED WARM-UP SYSTEM (AWS) OPERATION.

P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.

P011A WHEN STARTING IN COLD WEATHER BELOW 32 F (0 C). P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.

P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

OIL IS REPLACED EVEN IF THE PLUG IS TIGHTENED TO THE SPECIFIED TORQUE WITH A NEW GASKET. OIL PAN DRAIN PLUG TIGHTENING TORQUE: 3041 NM {3.14.1 KGFM, 2330 FTLBF} SEATING SURFACE OF THE OIL PAN FOR THE DRAIN PLUG MAY HAVE POOR FLATNESS DUE TO IMPROPER SPOT WELDING AND/OR THE SURFACE MAY HAVE GOTTEN A SCRATCH DURING MANUFACTURING PROCESS.

AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.

DTC P0191:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (EXCEPT 2014 MAZDA3) DTC P0088:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (2014 MAZDA3) THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED.

STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 F (-10 C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.

AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.

STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL.P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTEDTHIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 F (-10 C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

THIS CONCERN MAY BE CAUSED BY IMPROPER OPERATION OF THE NON-RETURN VALVE IN THE FUEL TANK (TEMPORARILY STUCK OPEN). THE PRODUCTION PROCESS OF THE FUEL TANK HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN.

THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES. ALL SKYACTIV ENGINES EQUIPPED WITH OIL PRESSURE SWITCH PART NUMBER PE01-18-501A ARE APPLICABLE TO THIS ISSUE.

P011A WHEN STARTING IN COLD WEATHER BELOW 32 F (0 C). P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM. THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.

STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 F (-10 C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.

TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON.

INTERNAL MALFUNCTION) WITH/WITHOUT U0401, OR OTHER DTCS STORED IN MEMORY.OTHER DTCS (WITH THE ABOVE DTCS) - P0746:00, P0751:00, P0752:00, P0756:00, P0757:00, P0761:00, P0762:00, P0766:00, P0767:00, P0771:00, P0772:00, P079A:00, P0842:00, P0843:00, P0847:00, P0848:00, P0872:00, P0873:00, P0877:00, P0878:00, P1784:00TO CORRECT THE PROBLEM, A NEW PROGRAMMED VALVE BODY HAS BEEN ESTABLISHED.

P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

DTC P0191:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (EXCEPT 2014 MAZDA3) DTC P0192:00: FUEL PRESSURE SENSOR CIRCUIT LOW INPUT (2014 MAZDA3) THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED.

P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION. NOTE: THIS SERVICE INFORMATION IS ALSO APPLICABLE IF DTC P0780:00 IS STOREED INDEPENDENTLY. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

RANGE: AN INTERMITTENT HIGH ENGINE IDLE SPEED. AN INTERMITTENT ENGAGEMENT SHOCK. AN INTERMITTENT FORWARD LURCH. THESE CONDITIONS MAY OCCUR WHEN THE CUSTOMER DEPRESSES THE BRAKE PEDAL AND MAKES CONTACT WITH THE THROTTLE PEDAL SIMULTANEOUSLY.

P0872 AND/OR P0877 STORED IN THE TCM MEMORY. P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON THE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER. P0780:00 - GEAR SHIFTING MALFUNCTION P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

P0872 AND/OR P0877 STORED IN THE TCM MEMORY. P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON THE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER. P0780:00 - GEAR SHIFTING MALFUNCTION P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

INCREASE WITH ENGINE SPEED THE ATX DOES NOT SHIFT UP OR DOWN AS EXPECTED. THE CONDITION MAY NOT ALWAYS BE ABLE TO BE REPRODUCED AND DTCS MAY NOT BE STORED WHEN THE VEHICLE IS BROUGHT IN. FOREIGN MATERIAL (IRON PARTICLES IN THE ATF) MAY ENTER THE ATX VALVE BODY AND CAUSE A TEMPORARY MALFUNCTION OF THE VALVE BODY AND/OR SENSOR (ATX FAIL-SAFE FUNCTION ACTIVATED). THE FAIL-SAFE FUNCTION IS CANCELED WITHOUT DTCS RECORDED IF THE MALFUNCTION GOES AWAY AND DOES NOT OCCUR AGAIN AT THE NEXT DRIVE CYCLE. FAIL-SAFE FUNCTION OPERATION: IF A TECHNICAL FAULT IS DETECTED IN THE ATX BY THE MALFUNCTION DETECTION FUNCTION, THE FAIL-SAFE FUNCTION LIMITS THE ATX CONTROL (INHIBITS SOME GEARS OR SHIFT DOWN FUNCTIONS). EVEN IN CASE OF AN ATX MALFUNCTION, THE FAIL-SAFE FUNCTION ALLOWS MINIMUM VEHICLE DRIVEABILITY.

INTERNAL MALFUNCTION) WITH/WITHOUT U0401, OR OTHER DTCS STORED IN MEMORY. OTHER DTCS (WITH THE ABOVE DTCS) - P0746:00, P0751:00, P0752:00, P0756:00, P0757:00, P0761:00, P0762:00, P0766:00, P0767:00, P0771:00, P0772:00, P079A:00, P0842:00, P0843:00, P0847:00, P0848:00, P0872:00, P0873:00, P0877:00, P0878:00, P1784:00 TO CORRECT THE PROBLEM, A NEW PROGRAMMED VALVE BODY HAS BEEN ESTABLISHED.

THIS CONCERN WILL MOST LIKELY OCCUR DURING THE VEHICLES FIRST FORWARD MOVEMENT AFTER STARTING THE ENGINE. THIS IS A NORMAL OPERATING NOISE OF THE ANTI-LOCK BRAKE SYSTEM (ABS). DO NOT ATTEMPT ANY REPAIRS.

INTERNAL MALFUNCTION) WITH/WITHOUT U0401, OR OTHER DTCS STORED IN MEMORY.OTHER DTCS (WITH THE ABOVE DTCS) - P0746:00, P0751:00, P0752:00, P0756:00, P0757:00, P0761:00, P0762:00, P0766:00, P0767:00, P0771:00, P0772:00, P079A:00, P0842:00, P0843:00, P0847:00, P0848:00, P0872:00, P0873:00, P0877:00, P0878:00, P1784:00TO CORRECT THE PROBLEM, A NEW PROGRAMMED VALVE BODY HAS BEEN ESTABLISHED.

INTERNAL MALFUNCTION) WITH/WITHOUT U0401, OR OTHER DTCS STORED IN MEMORY.OTHER DTCS (WITH THE ABOVE DTCS) - P0746:00, P0751:00, P0752:00, P0756:00, P0757:00, P0761:00, P0762:00, P0766:00, P0767:00, P0771:00, P0772:00, P079A:00, P0842:00, P0843:00, P0847:00, P0848:00, P0872:00, P0873:00, P0877:00, P0878:00, P1784:00TO CORRECT THE PROBLEM, A NEW PROGRAMMED VALVE BODY HAS BEEN ESTABLISHED.

THIS IS CAUSED BY ONE OF TWO THINGS. 1. EXCESSIVE CLEARANCE BETWEEN THE MAP LIGHT AND LAMP UNIT POSITIONING RIB (FOR MAZDA3 VEHICLES WITH VINS LOWER THAN JM1BL******144839 / PRODUCED BEFORE APRIL 1, 2009). THE DESIGN OF THIS RIB HAS NOW BEEN CHANGED TO CORRECT THIS PROBLEM. 2. THE OVERHEAD CONSOLE BRACKET VIBRATES AND CONTACTS THE ROOF PANEL (FOR MAZDA3 VEHICLES WITH VINS JM1BL******144839 TO JM1BL******707082 / PRODUCED AFTER APRIL 1, 2009 AND BEFORE AUGUST 8, 2012. THE NOISE OCCURS ON VEHICLES THAT HAVE A NON-WOVEN TEXTILE ATTACHED AT THE FRONT STAY. THE MATERIAL OF THE PADS HAS NOW BEEN CHANGED TO CORRECT THIS PROBLEM.

P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

LONGER THAN 20 MINUTES, THERE IS A POSSIBILITY THAT THE FUEL INSIDE THE HIGH-PRESSURE FUEL PUMP MAY BE RAISED TO A HIGHER TEMPERATURE THAN USUAL. IF THE FUEL TEMPERATURE IS HIGHER THAN THE FUEL VAPOR TEMPERATURE, THE FUEL SUPPLY TO THE INJECTOR MAY BE INSUFFICIENT AND POTENTIALLY CAUSE ONE OF THE FOLLOWING CONDITIONS: THE VEHICLE MAY EXPERIENCE ROUGH IDLE AND/OR THE MALFUNCTION INDICATOR LIGHT (MIL) MAY ILLUMINATE WITH DTC P0191:00 (FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM) STORED IN THE PCM MEMORY. THE ENGINE MAY STALL DURING STOP AFTER IDLING FOR A LONG TIME, AND MAY NOT RESTART FOR A CERTAIN PERIOD OF TIME.

LONGER THAN 20 MINUTES, THERE IS A POSSIBILITY THAT THE FUEL INSIDE THE HIGH-PRESSURE FUEL PUMP MAY BE RAISED TO A HIGHER TEMPERATURE THAN USUAL. IF THE FUEL TEMPERATURE IS HIGHER THAN THE FUEL VAPOR TEMPERATURE, THE FUEL SUPPLY TO THE INJECTOR MAY BE INSUFFICIENT AND POTENTIALLY CAUSE ONE OF THE FOLLOWING CONDITIONS: THE VEHICLE MAY EXPERIENCE ROUGH IDLE AND/OR THE MALFUNCTION INDICATOR LIGHT (MIL) MAY ILLUMINATE WITH DTC P0191:00 (FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM) STORED IN THE PCM MEMORY. THE ENGINE MAY STALL DURING STOP AFTER IDLING FOR A LONG TIME, AND MAY NOT RESTART FOR A CERTAIN PERIOD OF TIME.

THIS IS CAUSED BY STICK-SLIP NOISE OCCURING AT THE CONTACT SURFACES BETWEEN THE NO. 4 ENGINE MOUNT RUBBER AND THE NO. 4 ENGINE MOUNT BRACKET WHEN THE ENGINE SHAKES BACK AND FORTH. TO CORRECT THE PROBLEM, THE NO. 4 ENGINE MOUNT IS REPLACED AND GREASE IS APPLIED ON THE CONTACT SURFACES OF THE NO. 4 ENGINE MOUNT BRACKET.

USING THE DE-CHOKE MODE WITH NO DTC RECORDED. THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.DE-CHOKE MODE1.FULLY DEPRESS THE ACCELERATOR PEDAL AND CRANK THE ENGINE FOR 4 TO 5 SECONDS.2.TURN THE IGNITION SWITCH TO THE LOCK POSITION AND RELEASE THE ACCELERATOR PEDAL.3.START THE ENGINE WITHOUT DEPRESSING THE ACCELERATOR PEDAL.

THIS IS CAUSED BY DUST ENTERING BETWEEN THE REAR STABILIZER BUSHING AND STABILIZER BAR, WHICH WEARS DOWN THE BUSHING. TO CORRECT THE PROBLEM, THE REAR STABILIZER BAR IS REPLACED WITH A MODIFIED ONE (WITH A SET OF STABI-LIZER BUSHINGS AND BRACKETS).

INTERNAL MALFUNCTION) WITH/WITHOUT U0401, OR OTHER DTCS STORED IN MEMORY.OTHER DTCS (WITH THE ABOVE DTCS) - P0746:00, P0751:00, P0752:00, P0756:00, P0757:00, P0761:00, P0762:00, P0766:00, P0767:00, P0771:00, P0772:00, P079A:00, P0842:00, P0843:00, P0847:00, P0848:00, P0872:00, P0873:00, P0877:00, P0878:00, P1784:00TO CORRECT THE PROBLEM, A NEW PROGRAMMED VALVE BODY HAS BEEN ESTABLISHED.

INTERNAL MALFUNCTION) WITH/WITHOUT U0401, OR OTHER DTCS STORED IN MEMORY.OTHER DTCS (WITH THE ABOVE DTCS) - P0746:00, P0751:00, P0752:00, P0756:00, P0757:00, P0761:00, P0762:00, P0766:00, P0767:00, P0771:00, P0772:00, P079A:00, P0842:00, P0843:00, P0847:00, P0848:00, P0872:00, P0873:00, P0877:00, P0878:00, P1784:00TO CORRECT THE PROBLEM, A NEW PROGRAMMED VALVE BODY HAS BEEN ESTABLISHED.

WHILE SHIFTING AROUND 30 KM/H (19 MPH). THE ENGINE RPM RETURNS TO IDLE IF THE DRIVER TAKES THEIR FOOT OFF THE ACCELERATOR PEDAL. THIS CONCERN IS CAUSED BY IMPROPER CALIBRATION OF THE PCM FOR TORQUE TRIM CONTROL. TORQUE TRIM CONTROL IS USED ON THIS M/T TO ADJUST THE ENGINE RPM TO A SUITABLE SPEED FOR THE GEAR AFTER SHIFTING. THE FUNCTION ONLY WORKS WHEN THE DRIVER STEPS ON THE ACCELERATOR PEDAL WHILE SHIFTING TO HELP ACHIEVE SMOOTH SHIFTS. TO CORRECT THE PROBLEM, THE PCM SOFTWARE HAS BEEN MODIFIED.

AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT)THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.

THIS IS CAUSED BY STICK-SLIP NOISE OCCURRING AT THE CONTACT SURFACES BETWEEN THE NO. 4 ENGINE MOUNT RUBBER AND THE NO. 4 ENGINE MOUNT BRACKET WHEN THE ENGINE SHAKES BACK AND FORTH.

USING THE DE-CHOKE MODE WITH NO DTC RECORDED. THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.DE-CHOKE MODE1.FULLY DEPRESS THE ACCELERATOR PEDAL AND CRANK THE ENGINE FOR 4 TO 5 SECONDS.2.TURN THE IGNITION SWITCH TO THE LOCK POSITION AND RELEASE THE ACCELERATOR PEDAL.3.START THE ENGINE WITHOUT DEPRESSING THE ACCELERATOR PEDAL.

TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT.

THIS SERVICE BULLETIN IS TO INFORM YOU ABOUT THE WATER PUMP SEALING MECHA-NISM AND THE CRITERIA IF REPLACEMENT IS NECESSARY OR NOT.

THE UNIQUE OIL FILTER CAN BE IDENTIFIED WITH TWO WHITE BANDS AS SHOWN BELOW.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT

ON OR LOW ENGINE OIL PRESSURE. *LJ

OCV OR OIL PUMP PRESSURE RELIEF VALVE. MODEL 2012-2014 MAZDA3, MAZDA6, CX-5. *PE

MODEL 2012-2014. *PE

30KM/H (19MPH) AND THEN RETURNS TO IDLE WHEN FOOT RELEASES ACCELERATOR PEDAL. MODEL 2012-2013 MAZDA3. *PE

The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section once a part is selected. Accessories E-catalog For models prior to 2016: Accessory Parts and Installation Instructions

for download.

license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the resetting tool.

Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.

FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.

FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.

PROPER USE, AND PLACEMENT, OF DRIVER'S FLOOR MAT. VARIOUS MODELS AND MODEL YEARS. *PE

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a good know terminal.To measure the voltage/resistance avoiding any terminal damage.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps):CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery's Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda GR8-1291, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

The terminal test kit enables you: To check pin fit drag of all terminals used in SKYACTIV vehicles and compare suspect terminal drag with a good know terminal. To measure the voltage/resistance avoiding any terminal damage.

Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No. 2 (C) socket covers have not been correctly installed or are missing due to improper prior repairs (i.e., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, HID module seal (D), or missing bumper brackets (E) is not covered by warranty policy.

When you encounter a customer with this concern, first verify the condition when the customer noticed this symptom. If the condition is similar to the following "CONTROL LOGIC OF AMBIENT TEMPERATURE" or "DIFFERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS", advise the customer that this is a normal characteristic of the vehicle and not a malfunction. If the condition does not meet the following and the sensor malfunction is suspected, make sure to inspect the sensor according to MGSSonline or Workshop Manual (section 09-22 AMBIENT TEMPERATURE SENSOR INSPECTION). Replace the sensor only when it fails the Workshop Manual inspection.

prevent the battery from discharging.

Operations is 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

IF ALL THE BULB SOCKETS ARE RESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET OVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.

THE TEST KIT IS DESIGNED PECIFICALLY FOR SKYACTIV MODULE TERMINALS. THE SST WILL BE SHIPPED BY MAZDAS TOOL VENDOR BOSCH STARTING JANUARY 15, 2016. PROCEDURES FOR USAGE ARE FOUND IN THE SKYACTIV WIRING TERMINAL TEST KIT WBT, COURSE #1649. THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST:

OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS.

IF ALL THE BULB SOCKETS ARE PRESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET COVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.

THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED.

THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED.

THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.

IT IS MOST NOTICEABLE WHEN THE A/C IS FIRST TURNED ON. THIS ODOR IS THE RESULT OF MOLD GROWTH IN THE A/C EVAPORATOR/COOLING UNIT WHICH IS CAUSED BY CONDENSATION, DUST, AND POLLEN WITHIN THE COOLING UNIT. THIS CONDITION IS USUALLY WORSE DURING HIGH HUMIDITY CONDITIONS. MAZDA AIR COOLING COIL COATING IS AVAILABLE TO ENCAPSULATE THE MOLD TO REDUCE ODORS. IF THE PRODUCT IS PROPERLY APPLIED, IT CAN EFFECTIVELY REDUCE THE MUSTY/MILDEW ODOR FOR UP TO THREE YEARS.NOTE:SEE PARTS INFORMATION FOR MAZDA AIR COOLING COIL COATING AND KIT PART NUMBERS.

THIS CONCERN IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.

THIS CONCERN IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.

THIS CONCERN IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.

WHEN YOU ENCOUNTER A CUSTOMER WITH THIS CONCERN, FIRST VERIFY THE CONDITION WHEN THE CUSTOMER NOTICED THIS SYMPTOM. IF THE CONDITION IS SIMILAR TO THE FOLLOWING CONTROL LOGIC OF AMBIENT TEMPERATURE OR DIFFERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS, ADVISE THE CUSTOMER THAT THIS IS A NORMAL CHARACTERISTIC OF THE VEHICLE AND NOT A MALFUNCTION. IF THE CONDITION DOES NOT MEET THE FOLLOWING AND THE SENSOR MALFUNCTION IS SUSPECTED, MAKE SURE TO INSPECT THE SENSOR ACCORDING TO MS3 ONLINE OR WORKSHOP MANUAL (SECTION 09-22 AMBIENT TEMPERATURE SENSOR INSPECTION).

IF ALL THE BULB SOCKETS ARE PRESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET COVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.

IF AN AFTERMARKET ALARM SYSTEM IS INSTALLED, THE REAR HARNESS MIGHT HAVE RECEIVED DAMAGE FROM ELECTRO-TAP CONNECTORS (A) OR TO THE PROTECTOR TUBE (B). THIS DAMAGE IS NOT COVERED UNDER WARRANTY.

IF NOT USED, THE CONTROL MODULE REPROGRAMMING MAY FAIL DUE TO A WEAK VEHICLE BATTERY.THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE PREVENTS THE VEHICLE BATTERY FROM BEING DISCHARGED. THIS ALLOWS THE IDS TO REPROGRAM A CONTROL MODULE WITHOUT INTERFERENCE FROM A WEAK OR UNDERCHARGED VEHICLE BATTERY. NOTE: CONTROL MODULE DAMAGE MAY OCCUR IF THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE IS NOT USED.

THIS MAY BE CAUSED BY AN OBSTRUCTION OF THE FRONT AND/OR REAR LIGHT SENSOR(S) (E.G. HANGING A PARKING PERMIT FROM THE MIRROR). USE A SOFT CLOTH WITH MILD DETERGENT TO CLEAN THE MIRROR. HARSH DETERGENT MAY DAMAGE THE FRONT AND/OR REAR LIGHT SENSOR(S).

2010 MAZDA3 DASHBOARD UPPER PANEL STICKY SURFACE SSP99), TAKE CAUTION WHEN RE-CONNECTING CONNECTORS 0918-501 AND 0920-403. BOTH CONNECTORS ARE IDENTICAL AND NEAR THE SAME LOCATION. IF CONNECTED INCORRECTLY, MULTIPLE ELECTRICAL MALFUNCTIONS WILL OCCUR (E.G. HAZARD LIGHTS STAY ON).

SOME VEHICLES MAY EXHIBIT BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THEHANDLING OF BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CREATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010. CUSTOMERS EXPERIENCING RELATED CONCERNS SHOULD HAVE THEIR VEHICLE AND/OR DEVICE INSPECTED ACCORDING TO THE FOLLOWING PROCEDURE.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

configuration.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

and lines must be power flushed completely before an overhauled or replacement A/T is installed (except SKYACTIV-DRIVE). The most common cause of repeat A/T failures is lack of lubrication to the front and rear planetary gears. This is usually caused by an accumulation of metal particles and debris (from a previous A/T failure) on the internal mesh type baffle of the oil cooler. Power flushing will remove the restriction by back flushing, followed by forward flushing to dislodge a restriction, then back flushing again. This will in turn ensure full ATF flow for the transmission when it is operating.

The noise: Depends on the vehicles speed only (the more speed, the more noise) Occurs with all types of driving (acceleration, deceleration, steady speed) Does not depend on rpm, gear, or ATF temperature

bump when accelerating after deceleration at 25-40 mph (40-65 km/h) Hard to shift into 3rd, 4th, 5th, and/or 6th gear Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.

and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order to re-install the original plug from the old transmission.

NOTE: The following Caution is included with every ATX that requires configuration.

when accelerating after deceleration at 25-40 mph (40-65 km/h), Hard to shift into 3rd, 4th, 5th, and/or 6th gear, Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.

The noise: Depends on the vehicles speed only (the more speed, the more noise)Occurs with all types of driving (acceleration, deceleration, steady speed)Does not depend on rpm, gear, or ATF temperature.This is caused by a damaged bearing in the transaxle due to improper configuration of the transaxle case. A modification has now been implemented on automatic transaxles with the following serial numbers: 7TN0820364 and higher (CX-3) / 8TN1090104 and higher (except CX-3) 8TR1008883 and higher 8TD1003276 and higher 8T50331192 and higher (CX-3) / 8T50329705 and higher (except CX-3).

This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the driveshaft. To correct this issue, the thickness of the dust cover has been increased.

This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the drive shaft. To correct this issue, the thickness of the dust cover has been increased.

configuration.

This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the driveshaft. To correct this issue, the thickness of the dust cover has been increased.

Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

Using the wrong ATF may cause shift quality complaints or may even damage the transmission. NOTE: ATF M-V (TYPE M5) IS NOT THE SAME FLUID AS MERCONV OR MERCONLV ATF. ATF M-V (TYPE M5) HAS A GREATER VISCOSITY THAN MERCONV AND MERCONLV ATF IN LOW TEMPERATURES. ATF M-V (TYPE M5) HAS A GREATER ANTI-JUDDER SPECIFICATION THAN MERCONV AND MERCONLV ATF. TRANSMISSION FLUID FLUSHING SHOULD ONLY BE PERFORMED WHEN INSTRUCTED BY THE WORKSHOP MANUAL OR ANY OTHER MAZDA PUBLICATION.

when accelerating after deceleration at 25-40 mph (40-65 km/h), Hard to shift into 3rd, 4th, 5th, and/or 6th gear, Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.

when accelerating after deceleration at 25-40 mph (40-65 km/h) Hard to shift into 3rd, 4th, 5th, and/or 6th gear Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.

BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR SHIFT LEVER VIBRATES WHEN DRIVING IN 3RD OR 4TH GEAR THIS IS CAUSED BY INAPPROPRIATE TRANSMISSION INTERNAL PARTS.

THE NOISE: DEPENDS ON THE VEHICLES SPEED ONLY (THE MORE SPEED, THE MORE NOISE) OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED) DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE. THIS IS CAUSED BY A DAMAGED BEARING IN THE TRANSAXLE DUE TO IMPROPER CONFIGURATION OF THE TRANSAXLE CASE. A MODIFICATION HAS NOW BEEN IMPLEMENTED ON AUTOMATIC TRANSAXLES WITH THE SERIAL NUMBER 3TR1111680 AND HIGHER OR 3TD1104906 AND HIGHER. THE SERIAL NUMBER CAN BE FOUND ON TOP OF THE TRANSAXLE CASE NEAR THE MANUAL SHAFT LEVER.

BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR SHIFT LEVER VIBRATES WHEN DRIVING IN 3RD OR 4TH GEAR THIS IS CAUSED BY INAPPROPRIATE TRANSMISSION INTERNAL PARTS.

USING THE WRONG ATF MAY CAUSE SHIFT QUALITY COMPLAINTS OR MAY EVEN DAMAGE THE TRANSMISSION.NOTE: ATF M-V (TYPE M5) IS NOT THE SAME FLUID AS MERCONV OR MERCONLV ATF. ATF M-V (TYPE M5) HAS A GREATER VISCOSITY THAN MERCONV AND MERCONLV ATF IN LOW TEMPERATURES. ATF M-V (TYPE M5) HAS A GREATER ANTI-JUDDER SPECIFICATION THAN MERCONV AND MERCONLV ATF. TRANSMISSION FLUID FLUSHING SHOULD ONLY BE PERFORMED WHEN INSTRUCTED BY THE WORKSHOP MANUAL OR ANY OTHER MAZDA PUBLICATION. CAUTION: USING ATF OTHER THAN ATF M-V (TYPE M5) IN AUTOMATIC TRANSMISSIONS DESIGNED TO USE ATF M-V (TYPE M5) MAY CAUSE SHIFT QUALITY COMPLAINTS. USING ANY OTHER ATF OTHER THAN THE SPECIFIED ATF IN AUTOMATIC TRANSMISSIONS MAY CAUSE TRANSMISSION DAMAGE. USING A GENERIC, MULTI-PURPOSE OR UNIVERSAL ATF MAY CAUSE TRANSMISSION DAMAGE. DAMAGE TO THE TRANSMISSION CAUSED BY USING THE INCORRECT ATF, OR A GENERIC, MULTI-PURPOSE OR UNIVERSAL ATF WILL NOT BE COVERED BY WARRANTY.

ONLY USE ATF-FZ TO FILL OR TOP OFF THE FLUID LEVEL. ATF-FZ IS SPECIALLY DESIGNED FOR USE IN THE SKYACTIV-DRIVE SERIES AT. IT IS A LOW VISCOSITY FORMULA WITH LESS FRICTION FOR BETTER FUEL ECONOMY. NOTE: ATF-FZ IS COLORED BLUE FOR EASY IDENTIFICATION. TO CHECK THE FLUID LEVEL, REMOVE THE BOLT, THEN REMOVE THE DIPSTICK. THE DIPSTICK IS MARKED WITH A FZ ON SKYACTIV-DRIVE FW6A-EL AT. WHEN FINISHED, INSERT THE DIPSTICK AND INSTALL THE BOLT.

SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) THIS IS CAUSED BY A FAILURE OF THE RELATED CLUTCH HUB(S). TO CORRECT THE PROBLEM OF HARD SHIFTING, THE SHAPE OF THE 3-4 AND 5-6 CLUTCH HUB HAS BEEN CHANGED. A SURFACE TREATMENT HAS NOW BEEN ADDED TO THE 3-4 CLUTCH HUB TO PREVENT 3RD GEAR FROM JUMPING OUT.

THE NOISE: DEPENDS ON THE VEHICLES SPEED ONLY (THE MORE SPEED, THE MORE NOISE) OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED) DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE THIS IS CAUSED BY A DAMAGED BEARING IN THE TRANSAXLE DUE TO IMPROPER CONFIGURATION OF THE TRANSAXLE CASE. A MODIFICATION HAS NOW BEEN IMPLEMENTED ON AUTOMATIC TRANSAXLES WITH THE SERIAL NUMBER 3TR1111680 AND HIGHER OR 3TD1104906 AND HIGHER. THE SERIAL NUMBER CAN BE FOUND ON TOP OF THE TRANSAXLE CASE NEAR THE MANUAL SHAFT LEVER.

SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) THIS IS CAUSED BY A FAILURE OF THE RELATED CLUTCH HUB(S). TO CORRECT THE PROBLEM OF HARD SHIFTING, THE SHAPE OF THE 3-4 AND 5-6 CLUTCH HUB HAS BEEN CHANGED. A SURFACE TREATMENT HAS NOW BEEN ADDED TO THE 3-4 CLUTCH HUB TO PREVENT 3RD GEAR FROM JUMPING OUT.

THE SST WILL BE SHIPPED AUTOMATICALLY BY MAZDAS TOOL VENDOR SNAP-ON TOOLS, STARTING IN MID-OCTOBER 2014.THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST.

3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H)THIS IS CAUSED BY THE FRICTION COEFFICIENT BETWEEN THE 3/4 CLUTCH HUB AND THE SLEEVE INCREASING. A SURFACE TREAT-MENT HAS NOW BEEN ADDED TO THE 3/4 CLUTCH HUB TO DECREASE THE FRICTION COEFFICIENT.

THE NOISE:DEPENDS ON THE VEHICLES SPEED ONLY (THE MORE SPEED, THE MORE NOISE)OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED)DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE

THE NOISE: DEPENDS ON THE VEHICLES SPEED ONLY (THE MORE SPEED, THE MORE NOISE) OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED) DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE. THIS IS CAUSED BY A DAMAGED BEARING IN THE TRANSAXLE DUE TO IMPROPER CONFIGURATION OF THE TRANSAXLE CASE. A MODIFICATION HAS NOW BEEN IMPLEMENTED ON AUTOMATIC TRANSAXLES WITH THE SERIAL NUMBER TR1111680 AND HIGHER OR TD1104906 AND HIGHER. THE SERIAL NUMBER CAN BE FOUND ON TOP OF THE TRANSAXLE CASE NEAR THE MANUAL SHAFT LEVER.

THE NOISE: DEPENDS ON THE VEHICLES SPEED ONLY (THE MORE SPEED, THE MORE NOISE) OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED) DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE. THIS IS CAUSED BY A DAMAGED BEARING IN THE TRANSAXLE DUE TO IMPROPER CONFIGURATION OF THE TRANSAXLE CASE. A MODIFICATION HAS NOW BEEN IMPLEMENTED ON AUTOMATIC TRANSAXLES WITH THE SERIAL NUMBER TR1111680 AND HIGHER OR TD1104906 AND HIGHER. THE SERIAL NUMBER CAN BE FOUND ON TOP OF THE TRANSAXLE CASE NEAR THE MANUAL SHAFT LEVER.

THIS IS CAUSED BY MISS LEARNING OF THE TCM FOR SHIFT TIMING. TO CORRECT THE PROBLEM, THE LEARNING LOGIC OF THE TCM HAS BEEN CHANGED.

TO R POSITION OR N TO R POSITION. WHEN THE TRANSMISSION SHIFTS IMMEDIATELY AFTER STARTING TO MOVE (IN D POSITION). WHEN THE TRANSMISSION SHIFTS AT CRUISING SPEED (IN D POSITION). THE INITIAL LEARNING MAY NOT HAVE BEEN COMPLETED AT THE TIME OF VEHICLE PRODUCTION. TO CORRECT THE PROBLEM, ONE OR MORE LEARNING PROCEDURES MAY NEED TO BE PERFORMED.

THIS IS CAUSED BY MISS LEARNING OF THE TCM FOR SHIFT TIMING. TO CORRECT THE PROBLEM, THE LEARNING LOGIC OF THE TCM HAS BEEN CHANGED.

USING THE WRONG ATF MAY CAUSE SHIFT QUALITY COMPLAINTS OR MAY EVEN DAMAGE THE TRANSMISSION.NOTE:ATF M-V (TYPE M5) IS NOT THE SAME FLUID AS MERCONV OR MERCONLV ATF.ATF M-V (TYPE M5) HAS A GREATER VISCOSITY THAN MERCONV AND MERCONLV ATF IN LOW TEMPERATURES. ATF M-V (TYPE M5) HAS A GREATER ANTI-JUDDER SPECIFICATION THAN MERCONV AND MERCONLV ATF.

ONLY USE ATF-FZ TO FILL OR TOP OFF THE FLUID LEVEL. ATF-FZ IS SPECIALLY DESIGNED FOR USE IN THE SKYACTIV-DRIVE SERIES AT. IT IS A LOW VISCOSITY FORMULA WITH LESS FRICTION FOR BETTER FUEL ECONOMY.NOTE:ATF-FZ IS COLORED BLUE FOR EASY IDENTIFICATION.TO CHECK THE FLUID LEVEL, REMOVE THE BOLT, THEN REMOVE THE DIPSTICK. THE DIPSTICK IS MARKED WITH A FZ ON SKY-ACTIV-DRIVE FW6A-EL AT. WHEN FINISHED, INSERT THE DIPSTICK AND INSTALL THE BOLT.

USING THE WRONG ATF MAY CAUSE SHIFT QUALITY COMPLAINTS OR MAY EVEN DAMAGE THE TRANSMISSION.NOTE:ATF M-V (TYPE M5) IS NOT THE SAME FLUID AS MERCONV OR MERCONLV ATF.ATF M-V (TYPE M5) HAS A GREATER VISCOSITY THAN MERCONV AND MERCONLV ATF IN LOW TEMPERATURES. ATF M-V (TYPE M5) HAS A GREATER ANTI-JUDDER SPECIFICATION THAN MERCONV AND MERCONLV ATF.TRANSMISSION FLUID FLUSHING SHOULD ONLY BE PERFORMED WHEN INSTRUCTED BY THE WORKSHOP MANUAL OR ANY OTHER MAZDA PUBLICATION.

the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with an active SAT radio.

This may be caused by an aftermarket accessory device.

Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. If swapped, the SD card that is installed into the other vehicle becomes linked to the VIN of that vehicle.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.

dashboard replacement for sticky surface condition only is extended to 10 years (120 months) from the original Warranty Start Date, with no mileage limitations. Any other condition for dashboard replacement, such as discoloration, warp, or material splitting, is covered only for 36 months or 36,000 miles, whichever comes first. SSPA9 - 2010-2013 MAZDA3 - GAP BETWEEN INSTRUMENT PANEL AND INFORMATION DISPLAY WARRANTY EXTENSION PROGRAM: On certain 2010-2013 Mazda3 vehicles, the instrument panel just above the information display may be warping, generating a gap between the instrument panel and information display, if exposed to heat under high ambient temperature. The warranty coverage for instrument panel replacement due to warping or a gap is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date or April 30, 2018 whichever is later, with no mileage limitation.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement. NOTE: Always check for a TSB that may modify or eliminate prior authorization for a specific symptom for a given component.

for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active working SAT radio.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement. NOTE: Always check for a TSB that may modify or eliminate prior authorization for a specific symptom for a given component.

for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active (working SAT radio).

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT.

TO IMPROVE THE HANDLING OF BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.

B.THE DASHBOARD UPPER PANEL JUST ABOVE THE INFORMATION DISPLAY (A) IS WARPING, GENERATING A GAP (B).

TO SHOW ACTUAL TEMPERATURE.WHEN YOU ENCOUNTER A CUSTOMER WITH THIS CONCERN, FIRST VERIFY THE CONDITION WHEN THE CUSTOMER NOTICED THIS SYMPTOM. IF THE CONDITION IS SIMILAR TO THE FOLLOWING CONTROL LOGIC OF AMBIENT TEMPERATURE OR DIF-FERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS, ADVISE THE CUSTOMER THAT THIS IS A NOR-MAL CHARACTERISTIC OF THE VEHICLE AND NOT A MALFUNCTION.

FOR ANY REASON, A CALL MUST BE MADE TO INFORM SIRIUSXM OF THE EXISTING RADIO ID AND THE NEW/ REPLACEMENT SAT RADIO ID AS SOON AS POSSIBLE TO ENSURE THE CUSTOMER LEAVES THE DEALERSHIP WITH ACTIVE (WORKING SAT RADIO.

EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. PLEASE CONTACT THE APPROPRIATE SOURCE BY REFERRING TO THE FOLLOWING TABLES.

PROCEDURE AND PART EXCHANGE PROGRAM EFFECTIVE FEB. 08, 2010 ON APPLICABLE VEHICLES. DUE TO THE COMPLEXITY OF SOFTWARE AND HARDWARE AVAILABLE ON VARIOUS CELLULAR PHONES AND CELL PHONE PROVIDER NETWORKS, IT IS ESSENTIAL FOR CUSTOMERS TO CONTACT THE MAZDA HANDS-FREE SYSTEM CUSTOMER CARE NUMBER AT (800) 430-0153 OR, FOR CUSTOMERS REQUIRING ADDITIONAL RESOURCES, PLEASE DIRECT THEM TO WWW.MAZDAUSA.COM/BLUETOOTH. REPRESENTATIVES OF THE CUSTOMER CARE CENTER ARE KNOWLEDGEABLE ON VERIFYING APPROVED PHONES AND PROPERLY PAIRING (PROGRAMMING) SPECIFIC PHONES TO THE VEHICLES BLUETOOTH SYSTEM. THEY ARE ALSO BEST EQUIPPED TO RESOLVE A MAJORITY OF THE PAIRING ISSUES AND OTHER BLUETOOTH RELATED CONCERNS WHEN COMMUNICATING DIRECTLY WITH MAZDA CUSTOMERS.

SWITCH CONNECTOR WITH ANOTHER CONNECTOR, SUCH AS THE BLUETOOTH MICROPHONE CONNECTOR. THE TWO CONNECTORS HAVE THE SAME NUMBER OF PINS.

TO IMPROVE THE HANDLING OF BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.CUSTOMERS EXPERIENCING RELATED CONCERNS SHOULD HAVE THEIR VEHICLE AND/OR DEVICE INSPECTED ACCORDING TO THE FOLLOWING PROCEDURE.

REPLACE DASHBOARD.

THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

PHONE CALLS WHEN THE SMARTPHONE IS PAIRED WITH A VEHICLE OR WIRELESS HEADSET. THE ISSUE EXTENDS TO GPS VOICE NAVIGATION FOR SOME, BUT STREAMING MUSIC OVER BLUETOOTH APPEARS TO BE UNAFFECTED. SPECIFICALLY, DOZENS OF USERS IN THE APPLE SUPPORT COMMUNITIES AND MACRUMORS DISCUSSION FORUMS CLAIM TO BE EXPERIENCING DISTORTED, STATICKY, OR INAUDIBLE PHONE CALLS WHEN USING AN IPHONE SE. IF YOU EXPERIENCE A CUSTOMER COMPLAINT, AND THE CUSTOMER HAS A NEW IPHONE SE, DO NOT REPLACE ANY PARTS ON THE VEHICLE. EXPLAIN TO THE CUSTOMER THAT THE IPHONE MAY BE THE PROBLEM. HAVE THE CUSTOMER VISIT THIS WEBSITE: HTTP://WWW.MACRUMORS.COM/2016/04/11/IPHONE-SE-BLUETOOTH-PHONE-CALL-AUDIO-ISSUES/

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

vehicle service.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit. Tool Number Description Pricing PC1923MAZ Pro-Cut On-Car Brake Lathe Check eStore or call for current pricing OBTAINING TOOLS This tool can be ordered through Mazda eStore. You can log on to eStore at: http://dealers.mazdausa.com CUSTOMER SERVICE INFORMATION For warranty or product information contact Mazda Authorized Service Equipment at 877-768-6657. Customer service representatives are available from 7:30 AM until 7:00 PM CST, Monday through Friday. SPECIAL SERVICE TOOL (SST) PART NAME: OVERVIEW Pro-Cut On-Car Brake Lathe PART NUMBER: PC1923MAZ APPLICABLE MODELS: All USAGE: To machine brake rotors on the vehicle.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare subject to denial or debit.

vehicle service.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

(SSP) A0 - Mazda has now opened Warranty Extension SSPA0 to subject vehicles in all states. On April 23, 2018 parts available notification letters will be sent to 160,686 affected owners. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with Mazda Warranty Policy and Procedures.

Effective today, March 23rd orders for the Mazda6 crash pad, part number GSYL-60-350 can be placed using the DAG Restricted Parts Order screen on MXConnect. Orders will be VIN specific using the SSPA0 Restricted Parts Order screen. Please contact the Dealer Assistance Group if you need any assistance with an order for GSYL-60-350.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

vehicle service.

IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.

THIS IS CAUSED BY A WORN PAD (A) ON THE WINDOW REGULATOR CABLE FROM REPEATED OPERATION OF THE WINDOW GLASS (B) GOING UP AND DOWN. THE CABLE THEN DIRECTLY CONTACTS THE WINDOW GLASS WHEN RECEIVING VIBRATIONS, CAUSING A RATTLING NOISE.

LATHES AS AN OPTION FOR MNAO AUTHORIZED EQUIPMENT. DUE TO YOUR FEEDBACK AND AFTER EVALUATING A FEW ON-CAR BRAKE LATHES, WE ARE PLEASED TO ANNOUNCE THAT WE HAVE ADDED THE PRO CUT ON-CAR BRAKE LATHE TO MNAO AUTHORIZED EQUIPMENT PROGRAM. THE ACCU-TURN IS STILL AN APPROVED BRAKE LATHE BUT IT IS NO LONGER AVAILABLE FOR PURCHASE FROM OUR VENDOR. IMPORTANT REMINDER ROTORS MUST BE MACHINED USING A MAZDA APPROVED ON-CAR BRAKE LATHE OR WARRANTY CLAIMS ARE SUBJECT TO DENIAL OR DEBIT.

IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.

THIS CONCERN IS CAUSED BY INADEQUATE ALTERNATOR OUTPUT (CONTROLLED BY THE PCM) WHEN THE BATTERY IS UNDER A HEAVY LOAD. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.

IN MOST CASES THE OIL THAT IS PRESENT IS NORMAL, AND A RESULT OF THE OIL THAT REMAINS ON THE SHAFT DURING THE NORMAL SWEEPING PROCESS OF THE SHAFT SEAL. FOLLOW THE INSPECTION GUIDELINES TO DETERMINE IF THE CONDITION IS A RESULT OF THE NORMAL SWEEPING PROCESS OR A FAILURE OF THE SHAFT SEAL.

*PE

(CONTROLLED BY PCM) WHEN BATTERY EXPERIENCE HEAVY LOAD. MODEL 2012-2013 MAZDA3. *PE

This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.

This may be caused by the sun's reflection.

This may be caused by the sun's reflection.

This may be caused by the sun's reflection.

This may be caused by the sun's reflection.

This may be caused by the sun's reflection.

This may be caused by the sun's reflection.

This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.

remedy, and warranty coverage (if applicable).

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

The damage extends to the front surface of the aluminum wheel partly or entirely.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

remedy, and warranty coverage (if applicable).

This TSB has been superseded to SSPA9.

other similar tools be used to hold the lift gate stay dampers. Use only the tools specified in the recall. Vice Grips or other similar tools can easily damage the stay dampers. NOTE: Stay damper parts received with Vice Grip marks will not be covered under warranty.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.Use extra care when cleaning wheels. The following are guidelines to follow when cleaning the wheels.-Mazda recommends using a mild soap or neutral detergent as stated in the owner's manual under Appear-ance Care in the Maintenance and Care section.-DO NOT use a cleaning products containing strong acid or alkali contents to clean the wheels.-DO NOT apply any type of specialized wheel cleaner to the wheels when they are hot (such as after driving the vehicle or if the vehicle has sat in the sun). Ensure wheel temperatures are the same as ambient tem-perature before cleaning.-Within 15 minutes after any cleaner is applied, rinse the wheel thoroughly to completely remove cleaner.-Stains on Mazda Wheels caused by improper cleaning are not covered under the Mazda Vehicle Warranty.

WHEN THESE TYPES OF CLEANERS ARE USED TO CLEAN THE WHEELS ON MAZDA VEHICLES, THE CHEMICALS CONTENTS PENETRATE THE CLEAR COATING OF THE WHEEL SURFACE AND DAMAGE THE PAINT UNDER THE CLEAR COATING. THE DAMAGED AREA HAS THE APPEARANCE OF DARK STAINS.

AND/OR REAR WINDOW WHEN DRIVING ON UNEVEN ROAD SURFACE. THIS HAPPENS WHEN THE AMBIENT TEMPERATURE IS APPROXIMATELY 14 F (-10 C) OR LOWER AND THE VEHICLE CABIN HAS NOT YET WARMED UP. THE NOISE IS CAUSED BY THE WINDSHIELD AND/OR REAR WINDOW LOCATING STOPPER CONTACTING THE PANEL.

VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE SPEEDOMETER REPLACE-MENT LABEL. LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.

THIS IS CAUSED BY THE OIL CONTENT SEPARATING FROM THE GREASE APPLIED TO THE BEARING AND SPLINE SEEPING FROM THE SEAL AND BRACKET.THERE IS NO FUNCTIONAL PROBLEM WITH THIS ISSUE SINCE THE AMOUNT OF OIL SEEPAGE IS VERY SMALL COMPARED TO THE AMOUNT OF GREASE. NOTE THAT THE OIL SEEPAGE WILL STOP WHILE THE VEHICLE IS IN USE.IF YOU ENCOUNTER A CUSTOMER COMPLAINT ABOUT THIS CONCERN, WIPE OFF THE OIL WITH A RAG. DO NOT REPLACE THE JOINT SHAFT.

AND/OR REAR WINDOW WHEN DRIVING ON UNEVEN ROAD SURFACE. THIS HAPPENS WHEN THE AMBIENT TEMPERATURE IS APPROXIMATELY 14 F (-10 C) OR LOWER AND THE VEHICLE CABIN HAS NOT YET WARMED UP. THE NOISE IS CAUSED BY THE WINDSHIELD AND/OR REAR WINDOW LOCATING STOPPER CONTACTING THE PANEL.

THIS IS CAUSED BY A VIBRATION WHILE DRIVING.

THE PAINT MAY BECOME DAMAGED BY WEATHERSTRIP CHAFING CAUSED BY LIFTGATE/TRUNK LID VIBRATION WHILE DRIVING. TO ELIMINATE THIS CONCERN ON CX-5, SILICONE IS APPLIED TO THE LIP OF THE WEATHERSTRIP TO REDUCE FRICTION AGAINST THE LIFTGATE.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

NOTE: You may see ?Selection not available? on IDS when a selecting ?Programming menu?, 108.07 included a timer extension for Programming menu application that had to be installed before the expiration date of 3/27/18. After the expiration, IDS can?t accept the extension. To correct this, uninstall IDS and re-install IDS 108.00 >IDS 108.07 up-date. Select "Remove Mazda data files and settings" as shown below.

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear incertain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Damage can occur when using some cleaners that contain strong acid, alkaline cleanser or organic solvent. Damage caused by using these cleaners is not covered by Mazda's New Vehicle Limited Warranty term.

THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMP-TOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM.

THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMPTOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM.

MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNERS MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDAS FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.

THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMPTOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL HENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM.

MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNERS MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDAS FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.

MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNERS MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDAS FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.

WITHIN AND SHOULD BE CHECKED AND REPLACED, IF NECESSARY FOR CORRECT INSTALLATION. *PE

road.

balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?

FOLLOW STEERING WHEEL ALIGNMENT PROCEDURE.

The following are possible causes of floor mat interference, which can be avoided with proper usage.

The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.

05-005/14.THIS BULLETIN SUPERSEDES THE PREVIOUS BULLETINS 05-003/14 ISSUED ON 04/04/14 AND 02/21/14 AND 05-005/13 ISSUED ON 09/23/13, 9/25/13,12/16/13, AND 12/17/13

THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE. FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION. INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED. FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.

THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE.FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION.INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED.FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.

This may be caused by a loose spare tire jack.

This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.

THE VEHICLE CAN SLIP OFF THE JACK AND SERI-OUSLY INJURE SOMEONE. IN THIS SERVICE INFORMATION, SOME IMPORTANT WARNINGS AND CAUTIONS HAVE BEEN TAKEN FROM THE OWNERS MANUAL. FOR MAZDA CUSTOMERS WHO HAVE QUESTIONS ABOUT SAFELY LIFTING THEIR VEHICLE TO CHANGE A FLAT TIRE OR TO INSTALL SNOW CHAINS, PLEASE PROVIDE A COPY OF THE ATTACHED HANDOUT FOR THEM. ALSO, BE SURE TO ALWAYS DIRECT CUSTOMERS TO FOL-LOW THE DIRECTIONS IN THE OWNER'S MANUAL.

THIS MAY BE CAUSED BY A LOOSE SPARE TIRE JACK.

December 2017 Special Service Program SSPB3 - Takata Inflator Extended Warranty was announced. The extended warranty was a result of the Takata airbag inflator class action settlement. Mazda will provide supplemental warranty coverage for all repairs and replacements (including parts and labor) to correct any defects in the materials or workmanship of Takata airbag inflators and the replacement inflators installed pursuant to the Takata airbag recalls. The program covers defects in the Inflator only and does not cover other items in the airbag system. Additionally, the program also does not cover airbags that have properly deployed as a result of a collision.

Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.

INFORMATION REGARDING IMPORTING AND SELLING OF COUNTERFEIT AIRBAGS MANUFACTURED IN CHINA AND SOME 2004, 2010-2012 MAZDA3 VEHICLES MAY HAVE THEM INSTALLED. *PE

INFORMATION PROVIDED REGARDING THE SELLING AND IMPORTING OF COUNTERFEIT AIRBAGS MANUFACTURED IN CHINA, INSTALLING IN SOME VEHICLES. MODELS 2004, 2010-2012 MAZDA3. *PE

FACTORY OR DEALER INSTALLED AND TO CONTACT DEALERS OR MANUFACTURER IF CONCERN OR UNSURE OF AIR BAGS IN VEHICLES. MODELS 2004, 2010-2012 MAZDA3. *PE

This includes the use of intermediate positions.

THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.

THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.

Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. E85: A blend of 85% ethanol and 15% gasoline All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V.

INSTEAD, THE WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING EVAP LEAK TESTER WILL BE USED TO TROUBLESHOOT EVAP SYSTEM LEAKS.

uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.

Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version.

THIS NOISE MAY BE CAUSED BY A LOOSE REAR STABILIZER CONTROL LINK.