2016 Mazda Mazda2 TSBs

interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button

The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.

The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

may complain of leakage at or around the washer motor (1). This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section. This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location)

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on, P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on, P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on, P0780:00 - Gear shifting malfunction, P1738:00 Automatic transaxle internal malfunction. This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.

may complain of leakage at around the washer motor (1).This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section.

Some customers may complain about an unusual noise coming from the engine compartment for about 20 seconds after a cold engine start. This noise is a normal engine operation for improved exhaust gas emissions. The noise does not indicate a malfunction.

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? Yes - No repair is necessary. No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE).

This noise is a normal engine operation for improved exhaust gas emissions. The noise does not indicate a malfunction. ACCELERATED WARM-UP SYSTEM (AWS): All SKYACTIV-G engines adopt AWS to reduce exhaust gas emissions immediately after a cold engine start. AWS increases the engine idling speed and retards the ignition timing for about 20 seconds after the cold engine start to quickly warm up the catalytic converter. The customer may identify the engine sound during the AWS operation as a unusual noise.

The noise may be caused by a broken bound (bump) stopper that breaks because of deterioration from environmental factors and bad road conditions. To eliminate this concern, a dust boot has been added in order to protect the bound (bump) stopper from water and the mounting rubber has been changed accordingly.

DTC C0051:62 - EPS control module[when the vehicle is driven in a straight line, the difference between the steering angle (calculated by each sensor) and the steering angle (from the steering angle sensor) is greater than the specification]. This concern most likely occurs during the following situations: When the vehicle is turning in reverse, right after starting the engine. When the vehicle is going over a bump or a curb, right after starting the engine. This concern may be caused when the DSC HU/CM performs the steering center position calibration. During the learning process, if a shock is applied to the vehicle by a bump or curb etc., the steering center position may not be properly detected and creates a steering center position error. To eliminate this concern, the DSC HU/CM control software has been modified

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

A knocking/popping noise occurs when passing over speed bumps. A squeaking noise occurs when turning the steering wheel with vehicle at a standstill or at low speed. This is caused by the bump stopper (2) contacting the strut bearing (3) when the front shock absorber (1) is compressed. To eliminate this concern, the shape of the bump stopper has been modified.

NOTE: Engine misfire related DTCs (P0301, P0302, P0303, P0304) are usually stored at the same time. P0201:00 : Fuel injector circuit/open cylinder No.1 P0202:00 : Fuel injector circuit/open cylinder No.2 P0203:00 : Fuel injector circuit/open cylinder No.3 P0204:00 : Fuel injector circuit/open cylinder No.4 This concern may be caused by an internal failure of the PCM (DENSO produced only). To correct the concern, the PCM internal failure has been eliminated.

THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES.

BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT.

BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT

The film of the center display may be peeled off. White dots may appear on the center display. Spider web-like cracking appearing in the corner(s) of the MAZDA CONNECT center display (the cracks are internal and cannot be felt by touch).

Peeling, spider cracks and white dots.

The film of the center display may be peeled off. White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts.

- The film of the center display may be peeled off. - White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.

- The film of the center display may be peeled off. - White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.

screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.

screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.

It includes new display repair kit part numbers for the 2018-2019 Mazda2, 2018-2020 CX-3 and 2018-2020 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White dots

There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Please use the table below when ordering the screen repair kits. This can also be found in Service Alert SA-041/22.

- The film of the center display may be peeled off. - White dots may appear on the center display

Spider Cracks - Surface Peeling - White dots

Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.230 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software. Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.

All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.

After the installation of a new instrument cluster, the message "Fctry" is displayed instead of the odometer. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.

Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature.

This may be caused by an aftermarket accessory device.

Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. If swapped, the SD card that is installed into the other vehicle becomes linked to the VIN of that vehicle.

Replace the Active Driving Display.

This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping.The navigation SD card has a malfunction.

Replace the Active Driving Display.

MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux, Voice Command

MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. This concern may be a normal operation of the CMU connecting to available devices on start up.

REPLACE THE ACTIVE DRIVING DISPLAY.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

REPLACE THE ACTIVE DRIVING DISPLAY.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

This may be caused by the sun's reflection.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

This may be caused by the sun's reflection.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

This is caused by the gap between the roof molding attachment clips and the roof panel not being wide enough to allow paint to be appropriately applied to the roof panel. To eliminate this concern, the shape of the roof molding clip has been changed to enable paint application between the clip's rib and roof during the manufacturing process.

end causing a poor appearance and obstructing the view of the back window.

This may be caused by the sun's reflection.

This may be caused by the sun's reflection.

This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.

color) instead of athe conventional methanol type (blue color). This change is for European compliance Mazda has decided to make the change for all markets.

remedy, and warranty coverage (if applicable).

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

remedy, and warranty coverage (if applicable).

WHEN THESE TYPES OF CLEANERS ARE USED TO CLEAN THE WHEELS ON MAZDA VEHICLES, THE CHEMICALS CONTENTS PENETRATE THE CLEAR COATING OF THE WHEEL SURFACE AND DAMAGE THE PAINT UNDER THE CLEAR COATING. THE DAMAGED AREA HAS THE APPEARANCE OF DARK STAINS.

THIS CONCERN IS MOST LIKELY TO BE FOUND IN COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEN PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED ARE TO REMOVE STAIN(S).

the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. In most cases, if the left-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" can be completed without any problem (See CAUTION below for more details). Other possible symptoms that may be found if the right-side BSM module is replaced alone: BSM aiming fails BSM OFF" indicator ON Center Display warning message BSM failsafe (No operation) DTC U3000:54 stored in memory DTC U1A4B:54 stored in memory (CX-3, MX-5 only) NOTE: Since a new BSM control module does not retain the vehicle specification information, it is necessary to acquire and store the vehicle specification information transmitted via CAN communication from the combination meter through automatic configuration after replacement.

the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. Other possible symptoms that may be found if the right-side BSM module is replaced alone: * BSM aiming fails * "BSM OFF" indicator ON * Center Display warning message * BSM failsafe (No operation) * DTC U3000:54 stored in memory * DTC U1A4B:54 stored in memory (CX-3, MX-5 only)

Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . * The display operation does not fully open/close. * It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the act ive driving display which activates pinching detection. Customer having this concern should have their vehicle repaired using the following repair procedure.

This concern may also occur when a room fuse is installed in a new vehicle. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required. NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected.

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. Customers concern can be resolved by sanding off paint at ground point (3) where attachment bolt (4) is seated. After installing the bolt (4), apply touch-up paint to the exposed base material area of the front fender stay.

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.

This concern may also occur when a room fuse is installed in a new vehicle.Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected.CX-3 shown:Vehicles having this concern should have their vehicle repaired using the following procedure.

When you encounter a customer with this concern, first verify the condition when the customer noticed this symptom. If the condition is similar to the following "CONTROL LOGIC OF AMBIENT TEMPERATURE" or "DIFFERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS", advise the customer that this is a normal characteristic of the vehicle and not a malfunction. If the condition does not meet the following and the sensor malfunction is suspected, make sure to inspect the sensor according to MGSSonline or Workshop Manual (section 09-22 AMBIENT TEMPERATURE SENSOR INSPECTION). Replace the sensor only when it fails the Workshop Manual inspection.

Operations is 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

Forward Sensing Camera (FSC) and Laser Sensor. Replace the windshield with a new one instead.

TO COMPLETE THE RADAR AIMING PROCEDURE (IT IS OK TO REPLACE THE LEFT BSM ALONE). REASON IF THE RIGHT-SIDE BSM CONTROL MODULE IS REPLACED ALONE, AUTOMATIC CONFIGURATION IS NOT PERFORMED DUE TO A PROGRAM ERROR IN THE MODULE. BECAUSE OF THIS, THE REQUIRED BSM RADAR AIMING CANNOT BE PERFORMED. AUTOMATIC CONFIGURATION AS WELL AS BSM RADAR AIMING CAN BE PERFORMED, IF THE LEFT-SIDE BSM CONTROL MODULE IS REPLACED ALONE OR TOGETHER WITH THE RIGHT-SIDE BSM CONTROL MODULE.

TO COMPLETE THE RADAR AIMING PROCEDURE (IT IS OK TO REPLACE THE LEFT BSM ALONE). REASON IF THE RIGHT-SIDE BSM CONTROL MODULE IS REPLACED ALONE, AUTOMATIC CONFIGURATION IS NOT PERFORMED DUE TO A PROGRAM ERROR IN THE MODULE. BECAUSE OF THIS, THE REQUIRED BSM RADAR AIMING CANNOT BE PERFORMED. AUTOMATIC CONFIGURATION AS WELL AS BSM RADAR AIMING CAN BE PERFORMED, IF THE LEFT-SIDE BSM CONTROL MODULE IS REPLACED ALONE OR TOGETHER WITH THE RIGHT-SIDE BSM CONTROL MODULE.

IF NOT USED, THE CONTROL MODULE REPROGRAMMING MAY FAIL DUE TO A WEAK VEHICLE BATTERY.THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE PREVENTS THE VEHICLE BATTERY FROM BEING DISCHARGED. THIS ALLOWS THE IDS TO REPROGRAM A CONTROL MODULE WITHOUT INTERFERENCE FROM A WEAK OR UNDERCHARGED VEHICLE BATTERY. NOTE: CONTROL MODULE DAMAGE MAY OCCUR IF THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE IS NOT USED.

THIS MAY BE CAUSED BY AN OBSTRUCTION OF THE FRONT AND/OR REAR LIGHT SENSOR(S) (E.G. HANGING A PARKING PERMIT FROM THE MIRROR). USE A SOFT CLOTH WITH MILD DETERGENT TO CLEAN THE MIRROR. HARSH DETERGENT MAY DAMAGE THE FRONT AND/OR REAR LIGHT SENSOR(S).

IF THE HARNESS IS NOT CONNECTED PROPERLY, THE AD-DISP MAY NOT OPERATE.

IF THE HARNESS IS NOT CONNECTED PROPERLY, THE AD-DISP MAY NOT OPERATE.

IF RIGHT-DIDE BSM CONTROL MODULE REQURES REPLACEMENT FOR ANY REPAIR, ALSO REPLACE LEFT SIDE BSM CONTROL MODULE TO COMPELTE THE RADAR AIMING PROCEDURE (IT'S OK TO REPLACE THE LEFT BSM ALONE). IF THE RIGHT-SIDE BSM CONTROL MODULE IS REPLACED ALONE, "AUTOMATIC CONFIGURATION" IS NOT PERFORMED DUE TO PROGRAM ERROR IN MODULE. BECAUSE OF THIS, THE REQUIRED "BSM RADAR AIMING" CANNOT BE PERFORMED. "AUTOMATIC CONFIGURATION" AS WELL AS "BSM RADAR AIMING" CAN BE PERFORMED IF LEFT-SIDE BSM CONTROL MODULE IS REPLACED ALONE OR TOGETHER WITH RIGHT-SIDE BSM CONTROL MODULE.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

The system performance has been improved as follows: Ver. 74.00.324 fixes these software errors (bugs): * If the shift lever is operated quickly while displaying the CarPlayTM screen, the rear view screen may not return to the CarPlayTM screen. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into the R position.

Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

As the vehicle mileage increases, the ATF color changes. The color change does not affect vehicle performance.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. The accumulated coolant is solidified and plugs the gap in high temperature environment and the seepage is stopped and does not progress. This is normal and does not require a part replacement, clean off the dried coolant from around the pipe with a wire brush.

FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.

FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.

vehicle service.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

vehicle service.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with a vehicle ahead is imminent. In addition, the system reduces damage in the event of a collision by operating the brake control when the system determines that a collision is unavoidable. It may also be possible to avoid a collision depending on the relative speed between your vehicle and the vehicle in front of you. In addition, when the driver depresses the brake pedal, the brakes are applied firmly and quickly to assist.

IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.

If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.

If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.

If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.

IF ANY TYPE OF GREASE OR LUBRICATION IS APPLIED TO THE BUSHINGS, IT MAY CREATE NOISE DUE TO BUSHING SLIPPAGE.

THIS MAKES IT DIFFICULT TO CHANGE THE SEAT BACK RECLINING POSITION. THIS MAY BE CAUSED BY A RETURN RECLINER LEVER KNOB SPRING (A) THAT IS TOO STRONG

IF ANY TYPE OF GREASE OR LUBRICATION IS APPLIED TO THE BUSHINGS, IT MAY CREATE NOISE DUE TO BUSHING SLIPPAGE.

be wet.

be wet.

This includes the use of intermediate positions.

This may be caused by a refrigerant leak from the condenser due to corrosion where an anti-corrosion coating was uneven.

THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.

THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.

This may be caused by improper brazing (A) of the evaporator (B) causing a refrigerant leak fr om the joint between the tubes and the header (D)

Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).

This may be caused by improper brazing of the evaporator, causing a refrigerant leak from the joint between the tubes and the header.

Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).

This may be more noticeable when the outside temperature is approximately 50 degrees Fahrenheit (10 Celsius).

FAHRENHEIT (0 DEGREES CELSIUS).THE ACCELERATOR PEDAL HAS BEEN CHANGED TO INCREASE DURABILITY.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Damage can occur when using some cleaners that contain strong acid, alkaline cleanser or organic solvent. Damage caused by using these cleaners is not covered by Mazda's New Vehicle Limited Warranty term.

This may be caused by a loose spare tire jack.

This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.

THE VEHICLE CAN SLIP OFF THE JACK AND SERI-OUSLY INJURE SOMEONE. IN THIS SERVICE INFORMATION, SOME IMPORTANT WARNINGS AND CAUTIONS HAVE BEEN TAKEN FROM THE OWNERS MANUAL. FOR MAZDA CUSTOMERS WHO HAVE QUESTIONS ABOUT SAFELY LIFTING THEIR VEHICLE TO CHANGE A FLAT TIRE OR TO INSTALL SNOW CHAINS, PLEASE PROVIDE A COPY OF THE ATTACHED HANDOUT FOR THEM. ALSO, BE SURE TO ALWAYS DIRECT CUSTOMERS TO FOL-LOW THE DIRECTIONS IN THE OWNER'S MANUAL.

THIS MAY BE CAUSED BY A LOOSE SPARE TIRE JACK.

balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?

A VIBRATION IS FELT AT THE STEERING WHEEL WHEN THE NOISE OCCURS. THIS CONCERN MAY BE CAUSED BY A LACK OF GREASE APPLICATION TO THE SPLINES OF THE INTERMEDIATE SHAFT AT THE PRODUCTION LINE. THE GREASE APPLICATION PROCESS HAS BEEN IMPROVED.

The following are possible causes of floor mat interference, which can be avoided with proper usage.