2016 Mazda CX-5 TSBs

interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button

The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.

The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.

The changes are noted in Red text. MT-003/22 03/02/22 DESCRIPTION Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. The concern will likely occur if the fuel tank is overfilled (more fuel is added after the fuel pump nozzle shuts off automatically) or filled up normally in high ambient temperatures and the fuel expands. No repair is needed. Explain to the customer not to continue filling after nozzle shut off.

The changes are noted in Red. 01-008/23 06/05/23 Some vehicles may exhibit rattling noises from the engine compartment and oil leakage from the drive belt auto tensioner. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed. REPAIR PROCEDURE If the tensioner is found to be "No Good" after completing the Drive Belt Auto Tensioner Inspection, replace it with a modified part according to the instructions on MGSS online:

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). Only Mazda-approved key cutting machines can process these 10-digit codes. Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service. Examples of residue or seepage that may not be considered a leak and that may not require repair based on splash shield inspection.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

Foreign debris on the blower motor after servicing the cabin air filter may be the cause. During the removal of the cabin air filter, foreign debris (leaves, dust, dirt....ect.) may fall on the blower motor causing a fluttering type noise or odor.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

November 1, 2014 through May 13, 2016. If you are a recipient of this notice, your vehicle is included in Special Service Program (SSP) A6. What is the problem? Certain 2016 CX-5 vehicles were evaluated under NHTSAs new frontal oblique crash test, and the evaluation revealed that the fabric of the passenger frontal air bag may be torn during deployment of the air bag. NHTSA performed a frontal oblique crash being evaluated for inclusion in the New Car Assessment Program (NCAP). The NCAP test being evaluated is not a requirement of the current vehicle safety regulations or NCAP ratings, but will be used for NCAP safety ratings for future model year vehicles. Even though 2016 CX-5 vehicles fully satisfy the current vehicle safety regulations, we are conducting the SSP to minimize any potential safety risk. Action required: As previously advised the MDRT Tool loaner software expired July 15, 2020. All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by August 21, 2020. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge. New Mazda dealers that do not have this tool, please fill out the Dealer Recall Help form on MXConnect > Warranty to advise you do not have the tool.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

November 1, 2014 through May 13, 2016. If you are a recipient of this notice, your vehicle is included in Special Service Program (SSP) A6. What is the problem? Certain 2016 CX-5 vehicles were evaluated under NHTSAs new frontal oblique crash test, and the evaluation revealed that the fabric of the passenger frontal air bag may be torn during deployment of the air bag. NHTSA performed a frontal oblique crash being evaluated for inclusion in the New Car Assessment Program (NCAP). The NCAP test being evaluated is not a requirement of the current vehicle safety regulations or NCAP ratings, but will be used for NCAP safety ratings for future model year vehicles. Even though 2016 CX-5 vehicles fully satisfy the current vehicle safety regulations, we are conducting the SSP to minimize any potential safety risk. Action required: As previously advised the MDRT Tool loaner software expired July 15, 2020. All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by August 21, 2020. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge. New Mazda dealers that do not have this tool, please fill out the Dealer Recall Help form on MXConnect > Warranty to advise you do not have the tool.

November 1, 2014 through May 13, 2016. If you are a recipient of this notice, your vehicle is included in Special Service Program (SSP) A6. What is the problem? Certain 2016 CX-5 vehicles were evaluated under NHTSAs new frontal oblique crash test, and the evaluation revealed that the fabric of the passenger frontal air bag may be torn during deployment of the air bag. NHTSA performed a frontal oblique crash being evaluated for inclusion in the New Car Assessment Program (NCAP). The NCAP test being evaluated is not a requirement of the current vehicle safety regulations or NCAP ratings, but will be used for NCAP safety ratings for future model year vehicles. Even though 2016 CX-5 vehicles fully satisfy the current vehicle safety regulations, we are conducting the SSP to minimize any potential safety risk. Action required: As previously advised the MDRT Tool loaner software expired July 15, 2020. All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by August 21, 2020. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge. New Mazda dealers that do not have this tool, please fill out the Dealer Recall Help form on MXConnect > Warranty to advise you do not have the tool.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).

These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.

Vehicles having this concern should use the following Inspection/Repair procedure.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location)

fast idle to normal idle speed during cold start. This is caused by a variable valve being stuck in the closed position. When returning from fast idle to normal, the stuck valve suddenly opens due to thermal change around it which causes abnormal noise. To eliminate this concern, the internal design of the exhaust manifold has been modified.

Stored in TCM Memory

other engine air/fuel related DTC are stored. This may be caused by improper PCM control logic

The concern will likely occur if the fuel tank is overfilled (more fuel is added after the fuel pump nozzle shuts off automatically) or filled up normally in high ambient temperatures and the fuel expands. No repair is needed. Explain to the customer not to continue filling after nozzle shut off. Refer customer to Owner's Manual Warning:

Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline, E85: A blend of 85% ethanol and 15% gasoline, All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V. What if a customer puts E85 in there Mazda vehicle? Symptoms include: Rough Running, Lean Codes, Misfires and/or misfire codes, Lack of power, Poor fuel economy, Spark knock, Mechanical engine damage.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on, P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on, P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on, P0780:00 - Gear shifting malfunction, P1738:00 Automatic transaxle internal malfunction. This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.

This may be caused by a customer installed aftermarket decorative trim and/or cover on the START/STOP ENGINE button. The aftermarket accessory may create electrical interference, which may interfere with programming.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

This concern may be caused by companion flange oil seal wear. The oil seal has been improved to increase the wear resistance.

The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the case due to inadequate fabric wrapped around the cable. The fabric thickness has been increased to eliminate the noise.

As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

P2610:00: Instrument cluster internal engine off timer performance problem. P2507:00: PCM battery voltage low input

higher.

when turning the steering wheel while the vehicle is stopped.

P0015:00 - Exhaust CMP timing over-retarded, P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.

Some vehicles may exhibit a knocking noise from the rear of the vehicle. Upon inspection, cracks may be found in rear differential mount bushing, causing the noise. The is caused by insufficient durability of the bushing. To eliminate the noise, the shape of the bushing has been changed.

and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery voltage low input.

As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? Yes - No repair is necessary. No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE).

head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H

This noise is a normal engine operation for improved exhaust gas emissions. The noise does not indicate a malfunction. ACCELERATED WARM-UP SYSTEM (AWS): All SKYACTIV-G engines adopt AWS to reduce exhaust gas emissions immediately after a cold engine start. AWS increases the engine idling speed and retards the ignition timing for about 20 seconds after the cold engine start to quickly warm up the catalytic converter. The customer may identify the engine sound during the AWS operation as a unusual noise.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic.

P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display F0-002 during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km).Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear Parking Sensors - Rear Seat Entertainment - Smartphone Screen Mirroring - Bumper Trim/Guards - Door Mirror Caps - Fog Lights - Moonroof Wind Deflector - Roof Rack - Side Window Deflectors - Splash Guards - Trailer Hitch - Thule Products - Wheels Locks - Aero Kit - Air Dam - Rear Spoiler - Tunnel Under Bars - Lower Arm Bar - Side Sill Extensions - Arm Rest - Illuminated Door sill Trim Plates - Interior Lighting

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.

Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.

This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.

Engine Start/Start Button Amber indicator light flashing Battery discharge Electrical relay buzzing noise DTC B13D3:94 (Communication error with remote transmitter) stored.This may be caused by: A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehicless wiring harness may create unusual electrical symptoms.

This may be caused by a poor C-11 or C-12 electrical connection.

This may be caused by a plugged heater core. For 2014-2016 Mazda6 and 2013-2016 (US spec) / 2017 (Mexico spec) CX-5, the CHECK ENGINE light may turn on with DTC P011A:00 (ECT sensor No.1/No.2 performance problem) stored at the same time. NOTE: Refer to TSB 01-015/15 if the customer is using a block heater at temperatures below freezing. To solve this concern, two mass production changes have been implemented. a) The concentration of the coolant has been increased so that the amount of the contained anti-rust additive is higher. b) The composition of the coolant has been changed (the ratio of the anti-rust additive has increased).

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.

DTC C0051:62 - The difference between the initial learned value of the steering angle (as calculated by each sensor) and the steering angle (as calculated by the steering angle sensor) while driving in a straight line, has exceeded its allowable tolerance (or threshold). NOTE: For vehicles equipped with the Smart City Brake System (SCBS), the master warning light also comes ON with the message "SCBS Inspection Required" in the display. The symptoms may occur when the following conditions are met: After starting the engine, the vehicle is driven backwards while the steering wheel is turned to the left or to the right or going forward over a bump while turning the steering wheel. The vehicle is then driven forward and begins accelerating while the steering wheel is still turned. To eliminate this concern, the DSC HU/CM software has been changed.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 - Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.

when driving in high temperatures at high elevations. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem This concern may be caused by improper PCM control logic. The engine torque calculation error may increase in high temperatures at high elevations. To eliminate this concern, the PCM software has been modified.

DTC C0051:62 - The difference between the initial learned value of the steering angle (as calculated by each sensor) and the steering angle (as calculated by the steering angle sensor) while driving in a straight line, has exceeded its allowable tolerance (or threshold). NOTE: For vehicles equipped with the Smart City Brake System (SCBS), the master warning light also comes ON with the message "SCBS Inspection Required" in the display. The symptoms may occur when the following conditions are met: After starting the engine, the vehicle is driven backwards while the steering wheel is turned to the left or to the right or going forward over a bump while turning the steering wheel. The vehicle is then driven forward and begins accelerating while the steering wheel is still turned. To eliminate this concern, the DSC HU/CM software has been changed.

when driving in high temperatures at high elevations. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem.This concern may be caused by improper PCM control logic. The engine torque calculation error may increase in high temperatures at high elevations. To eliminate this concern, the PCM software has been modified.

lock release button (1) on the selector lever knob. Although the selector lever is in the "P" position and the engine shuts off normally, the ignition may stay on (in accessory mode). NOTE: This TSB only applies if the selector lever knob is BHN2-46-030* or BHN4-46-030* with the lock release button. If not, this TSB does not apply. This may be caused by the lock release button in the selector lever knob sticking in the pressed position. An improper production process is causing an internal part to expand with moisture and interfere with other parts. To eliminate this concern, the production process has been modified.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial checkis a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.

Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory. P0300 - Random misfire detected P0301 - Cylinder No. 1 misfire detected P0302 - Cylinder No. 2 misfire detected P0303 - Cylinder No. 3 misfire detected P0304 - Cylinder No.4 misfire detected. This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow.

Unlike previous Mazda models, there is no key cylinder on the steering column. Therefore, the engine cannot be started with the auxiliary key if the room fuse is removed or if the transmitter battery is dead.

P0456: EVAP system leak detected (very small leak). The concern is most likely the result of the customer not getting the fuel cap completely closed after fueling the vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.

The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. This can happen if the ignition is turned OFF within 20 seconds after the ignition is turned ON in one of the following two situations. 1. The ?ROOM? fuse (Engine compartment) is NOT installed when battery level is low. 2. The CMU (Connectivity Master Unit) is NOT connected.

refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.

These symptoms may be caused by a broken rear coil spring at its lower side. This is caused by corrosion from dust between the rear coil spring and the spring sheet, resulting in a broken rear coil spring. To eliminate this concern, the shape of the rear coil spring has been modified.

deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. This can happen if the ignition is turned OFF within 20 seconds after the ignition is turned ON in one of the following two situations. 1. The ?ROOM? fuse (Engine compartment) is NOT installed when battery level is low. 2. The CMU (Connectivity Master Unit) is NOT connected.

refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

when driving in high temperatures at high elevations. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. This concern may be caused by improper PCM control logic. The engine torque calculation error may increase in high temperatures at high elevations. To eliminate this concern, the PCM software has been modified.

memory.DTC C0051:62 - The difference between the initial learned value of the steering angle (as calculated by each sensor) and the steering angle (as calculated by the steering angle sensor) while driving in a straight line, has exceeded its allowable tolerance (or threshold). NOTE: For vehicles equipped with the Smart City Brake System (SCBS), the master warning light also comes ON with the message "SCBS Inspection Required" in the display. The symptoms may occur when the following conditions are met: After starting the engine, the vehicle is driven backwards while the steering wheel is turned to the left or to the right or going forward over a bump while turning the steering wheel. The vehicle is then driven forward and begins accelerating while the steering wheel is still turned. To eliminate this concern, the DSC HU/CM software has been changed.

This concern may be caused by companion flange oil seal wear. The oil seal has been improved to increase the wear resistance.

These symptoms may be caused by a broken rear coil spring at its lower side. This is caused by corrosion from dust between the rear coil spring and the spring sheet, resulting in a broken rear coil spring. To eliminate this concern, the shape of the rear coil spring has been modified.

It becomes very noticable with dust adhesion. In some cases, the area of oil residue extends down to around the joint portion (B) between the engine front cover and the oil pan. This may be caused by oil escaping from a fine clearance created at the sealant applied to joint (A) between the cylinder block (B) and head (C) when the engine was pressurized during leak testing on the engine assembly line.

The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system. When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur to oxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise.This may be caused by: A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehicles?s wiring harness may create unusual electrical symptoms.

A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger, GPS tracker...) may create excessive electrical noise. The noise may interrupt some of the vehicle electrical systems. Below are a few examples of an aftermarket cell phone charger and GPS tracker that are interrupting the vehicle electrical systems.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing.

complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger) may create excessive electrical noise. The noise may interrupt some of the vehicle electrical systems. Below are a few examples of an aftermarket cell phone charger that is interrupting the vehicle electrical systems.

(e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the cable casing due to inadequately wrapped fabric around the cable. To eliminate this concern, the power seat cable has been changed to a type that produces less friction and noise.

temperature), the engine oil may become diluted with fuel and the engine oil level will increase. Engine oil dilution with fuel occurring under this specific driving condition is normal with direct injection engines. If the vehicle is driven on a longer trip after a lot of short trips (where the engine reaches normal operating temperature), the Check Engine Light may turn ON with DTC P0172:00 (Fuel system too rich).

P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely closed after fuelingthe vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.

P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/Cevaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers. This treatment provides a durable coating that will aid to prevent biological reactions that lead to odorconcerns. It is applied to the evaporator in a misted form that is introduced by way of the cabin air filter, the re-circulate door, the blower motor resistor access, or the blower motor air intake. Proper application requires the evaporator surface to be: Relatively clean and free of leaves, dust build-up and debris. Thoroughly dried, and the product cured onto it after application. NOTE: Keep the cooling unit dry by leaving the blower fan ON (at least on low), even if the A/C is not being used. In low humidity (dry) conditions, keep the ventilation system in the "FRESH" mode all the time, or as much as possible. In high humidity conditions, or if the air has a lot of dust or pollen, keep the system in the "RECIRCULATION" mode. A few minutes before reaching a destination, turn the A/C OFF, but leave the blower fan ON. This stops the accumulation of condensation on the evaporator/cooling unit, and it helps dry the inside of the cooling unit. A/C odor is not unique to Mazda vehicles as it will occur in other makes and models. To minimize A/C odor, suggest the following to the customers.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to MGSS online for proper diagnosis and repair procedure.

This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial check is a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.

Unlike previous Mazdamodels, there is no key cylinder on the steering column. Therefore, the engine cannot be started with theauxiliary key if the room fuse is removed or if the transmitter battery is dead.NOTE: The auxiliary key can only be used to lock or unlock the doors. It cannot be used to start the engine. Two transmitters are placed in a vinyl bag and stored in the center console cup holder. Since the room fuse is not installed during vehicle assembly, a new procedure is required to start the engine. Refer to "Engine Start Procedure" below.

P0015:00 - Exhaust CMP timing over-retarded P0524:00 - Engine oil pressure too low This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.

The unique oil filter can be identified with two white bands as shown below.

Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory. P0300 - Random misfire detected P0301 - Cylinder No.1 misfire detected P0302 - Cylinder No.2 misfire detected P0303 - Cylinder No.3 misfire detected P0304 - Cylinder No.4 misfire detected. This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow.

The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the cable casing due to inadequately wrapped fabric around the cable. To eliminate this concern, the power seat cable has been changed to a type that produces less friction and noise.

when turning the steering wheel while the vehicle is stopped.The noise may be due to: Upper front strut bearing (A) damage. (CX-5 and Mazda6) Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6) The bump stopper (C) may be contacting the strut bearing when the front shock absorber is compressed, causing a popping noise. (Mazda6 only) The front lower arm bushing (D) is making a creak type noise in wet road conditions. (CX-5 and Mazda6).Front Shock Absorber Front Lower Arm To eliminate the noise, the following mass-production changes have been made: 1. The material and production method of the front strut bearing (A) has been changed. (CX-5 and Mazda6) 2. A protector has been installed onto the coil spring. (CX-5 and Mazda6) 3. The shape of the bump stopper (C) will be modified in the future. (Mazda6 only) 4. The shape of the coil spring has been changed. (CX-3 only) 5. Friction of the lower arm bushing has been reduced by adding a dry coating. (CX-5 and Mazda6). NOTE: The piston rod nut (B) requires replacement.

Vehicles having this concern should use the following Inspection/Repair procedure.

service loaner program for Special Service Program (SSPA6). The purpose of this email is to inform all Mazda dealerships that the loaner program has been extended for an additional 3 months to improve the completion rate for campaign SSPA6.

This may be caused by a clogged heater unit. For Mazda6 and CX-5, the check engine light may illuminate with the DTC P011A:00 stored at the same time. P011A:00 ECT sensor No.1/No.2 performance problem. NOTE: Refer to TSB 01-015/15 if the customer is using a block heater at temperatures below freezing.

P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.

NOTE: Engine misfire related DTCs (P0301, P0302, P0303, P0304) are usually stored at the same time. P0201:00 : Fuel injector circuit/open cylinder No.1 P0202:00 : Fuel injector circuit/open cylinder No.2 P0203:00 : Fuel injector circuit/open cylinder No.3 P0204:00 : Fuel injector circuit/open cylinder No.4 This concern may be caused by an internal failure of the PCM (DENSO produced only). To correct the concern, the PCM internal failure has been eliminated.

when turning the steering wheel while the vehicle is stopped.The noise may be due to:? Upper front strut bearing (A) damage. (CX-5 and Mazda6)? Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6)? The bump stopper (C) may be contacting the strut bearing when the front shock absorber is compressed, causing a popping noise. (Mazda6 only)? The front lower arm bushing (D) is making a creak type noise in wet road conditions. (CX-5 and Mazda6).

It becomes very noticable with dust adhesion. In some cases, the area of oil residue extends down to around the joint portion (B) between the engine front cover and the oil pan. This may be caused by oil escaping from a fine clearance created at the sealant applied to joint (A) between the cylinder block (B) and head (C) when the engine was pressurized during leak testing on the engine assembly line.

November 1, 2014 through May 13, 2016. Certain 2016 vehicles were evaluated under NHTSA?s new frontal oblique crash test, and the evaluation revealed that the fabric of the passenger frontal air bag may be torn during deployment of the air bag.NHTSA performed a frontal oblique crash being evaluated for inclusion in the New Car Assessment Program (NCAP). The NCAP test being evaluated is not a requirement of the current vehicle safety regulations or NCAP ratings, but will be used for NCAP safety ratings for future model year vehicles. Even though 2016 CX-5 vehicles fulfill current vehicle safety regulations, Mazda is conducting this SSP to minimize any potential safety risk. The purpose of this SSP is to reprogram the Sophisticated Air Bag Sensor (SAS) unit with modified software. Bosch will ship a Mazda Diagnostic Reprogramming Tool Kit (MDRT3-1) to all dealers on November 28, 2016. Please refer to the Repair Procedure document posted on MS3 for details.

when turning the steering wheel while the vehicle is stopped. The noise may be due to: Upper front strut bearing (A) damage. (CX-5 and Mazda6). Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6). The bump stopper (C) may be contacting the strut bearing when the front shock absorber is compressed, causing a popping noise. (Mazda6 only). The front lower arm bushing (D) is making a creak type noise in wet road conditions. (CX-5 and Mazda6).

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the ?SpeedometerReplacement Label?.Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda?s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.With the use of SPECMO?s services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

service loaner program for Special Service Program (SSPA6). The purpose of this email is to inform all Mazda dealerships that we are expanding the loaner program for 3 months to improve the significantly low completion rate for campaign SSPA6.

It becomes very noticable with dust adhesion. In some cases, the area of oil residue extends down to around the joint portion (B) between the engine front cover and the oil pan.

when turning the steering wheel while the vehicle is stopped. The noise may be due to: *upper front strut bearing (A) damage. (CX-5 and Mazda6) *squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6) *the bump stopper (C) may be contacting the strut bearing when the front shock absorber is compressed, causing a popping noise. (Mazda6 only) *The front lower arm bushing (D) is making a creak type noise in wet road conditions. (CX-5, Mazda6 and CX-9).

Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory.?P0300 - Random misfire detected ?P0301 - Cylinder No.1 misfire detected ?P0302 - Cylinder No.2 misfire detected ?P0303 - Cylinder No.3 misfire detected ?P0304 - Cylinder No.4 misfire detected This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow.

LANE DEPARTURE WARNING SYSTEM (LDWS) WARNING LIGHT TURNS ON AT IDLE. DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY.2.ADAPTIVE LED HEADLIGHTS (ALH) WARNING LIGHT TURNS ON WHILE DRIVING. DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY.UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR).

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION P1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO: UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6) STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY) TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE: 1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6) 2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6) 3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY) 4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY) NOTE: THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES.

P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.

WARNING SYSTEM (LDWS) WARNING LIGHT TURNS ON AT IDLE. DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY.2. ADAPTIVE LED HEADLIGHTS (ALH) WARNING LIGHT TURNS ON WHILE DRIVING. DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY.UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR).

THAT THEY MAY BE COMPLETELY INOPERATIVE. THIS CONCERN MAY BE CAUSED BY A FOREIGN OBJECT GETTING STUCK UNDER THE POWER SLIDE UNIT (BELOW) WHILE IN OPERATION. THIS CAN CAUSE MOTOR MOUNTING BRACKET (A) DEFORMATION, RESULTING IN MOTOR CABLE (B) BREAKAGE. TO ELIMINATE THIS CONCERN, THE SHAPE OF THE MOTOR MOUNTING BRACKET (A) HAS BEEN MODIFIED TO INCREASE ITS STRENGTH.

P2610:00: INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM P2507:00: PCM BATTERY VOLTAGE LOW INPUT AS A PAST MALFUNCTION, THE CUSTOMER WILL NOT NOTICE IT (NO WARNING LIGHT ILLUMINATED), BUT THE DTC MAY BE FOUND DURING A VEHICLE SERVICE. P2507 IN THIS SITUATION IS ONLY APPLICABLE ON 2016 AND LATER MODELS. THIS IS CAUSED BY THE ENGINE BEING STARTED 3 OR MORE TIMES AFTER A SHORT DURATION OF ENGINE OFF (LESS THAN 15 SECONDS) WITH THE ROOM FUSED REMOVED.

P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON.

DTC P013A:00: HO2S SLOW RESPONSE (DURING TRANSITION FROM RICH TO LEAN) THIS CONCERN MAY BE CAUSED BY AN IMPACT FROM A SPEED-BUMP OR OTHER SOURCE, CAUSING A DEFORMATION OF THE GASKET BETWEEN THE EXHAUST MANIFOLD (WU-TWC) (A) AND THE TWC (B).

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

P011A WHEN STARTING IN COLD WEATHER BELOW 32 F (0 C). P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.

P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6)TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO UPPER FRONT STRUT BEARING DAMAGE OR IT MAY BE DUE TO STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE: 1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING HAS BEEN CHANGED. 2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. NOTE: THE PISTON ROD NUT (B) REQUIRES REPLACEMENT WHEN THE FRONT STRUT BEARING IS REPLACED.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.

THE PURPOSE OF A PERMANENT DTC IS TO PREVENT CUSTOMERS FROM CLEARING THEM BY DISCONNECTING THE BATTERY CABLE IN ORDER TO PASS A SMOG CHECK. ALL PCM AND TCM DTCS THAT TURN ON THE CHECK ENGINE LIGHT CAN REMAIN AS A PERMANENT DTC. THEY WILL NOT TURN ON THE CHECK ENGINE LIGHT OR CAUSE DRIVABILITY CONCERNS. IF YOU ENCOUNTER A PERMANENT DTC, IGNORE IT AND DIAGNOSE THE CURRENT STORED OR PENDING DTC.

THIS OCCURS WHEN THE VEHICLE IS COLD AND CANNOT BE DUPLICATED ONCE THE VEHICLE IS AT NORMAL OPERATING TEMPERATURE. THE CREAKING NOISE MAY BE CAUSED BY THE #4 ENGINE MOUNT. THE NOISE CAN EASILY BE MISTAKEN FOR SUSPENSION RELATED COMPONENTS AND IS VERY DIFFICULT TO DIAGNOSE.

THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES. ALL SKYACTIV ENGINES EQUIPPED WITH OIL PRESSURE SWITCH PART NUMBER PE01-18-501A ARE APPLICABLE TO THIS ISSUE.

-4 TO 14 DEGREES F (-20 TO -10 DEGREES C), SOME VEHICLES MAY EXHIBIT THE ELECTRIC PARKING BRAKE (EPB) WARNING LIGHT ON WITH ONE OR MORE OF THE FOLLOWING DTCS PRESENT. C112A:77 INCORRECT ELECTRIC PARKING BRAKE MOTOR GEAR UNIT POSITION. C2005:07 MECHANICAL PROBLEM OF ELECTRIC PARKING BRAKE MOTOR GEAR UNIT (RH). C2005:19* ELECTRIC PARKING BRAKE MOTOR GEAR UNIT (RH) CIRCUIT MALFUNCTION. C2005:74 ELECTRIC PARKING BRAKE MOTOR GEAR UNIT (RH) POWER TRANSMISSION IMPOSSIBLE (SPIN). C2006:07 MECHANICAL PROBLEM OF ELECTRIC PARKING BRAKE MOTOR GEAR UNIT (LH). C2006:19* ELECTRIC PARKING BRAKE MOTOR GEAR UNIT (LH) CIRCUIT MALFUNCTION. C2006:74 ELECTRIC PARKING BRAKE MOTOR GEAR UNIT (LH) POWER TRANSMISSION IMPOSSIBLE (SPIN). NOTE: * DTCS C2005:19 AND/OR C2006:19 SHOULD ALWAYS BE PRESENT. IF NEITHER DTC IS PRESENT, THIS BULLETIN IS NOT APPLICABLE TO THE SUBJECT VEHICLE. PROCEED WITH NORMAL TROUBLESHOOTING PROCEDURES ACCORDING TO MS3 ONLINE OR THE WORKSHOP MANUAL. THIS CONDITION OCCURS WHEN PRESSING THE EPB SWITCH TO RELEASE THE ELECTRIC PARKING BRAKE, HOWEVER, THE EPB WILL NOT RELEASE.THIS CONCERN MAY BE CAUSED BY THE EPB MOTOR GEAR UNIT (A) DIMENSIONS BEING OUT OF SPECIFICATION. THE MACHINING DIMENSIONS OF EPB MOTOR GEAR UNIT HAVE BEEN IMPROVED TO ELIMINATE THIS CONCERN.

P011A WHEN STARTING IN COLD WEATHER BELOW 32 F (0 C). P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM. THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.

6,000 RPM) IN COLD WEATHER CONDITIONS BELOW 32 F (0 C). DTCS P0300:00, P0301:00 AND/OR P0302:00 ARE STORED IN MEMORY. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO. 1 MISFIRE DETECTED P0302:00: CYLINDER NO. 2 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. THE PCM MAY DETECT A FALSE MISFIRE UNDER THE SUBJECT CONDITIONS AND MAY FALL INTO FAIL SAFE MODE. TO ELIMINATE THIS CONCERN, THE PCM CONTROL LOGIC HAS BEEN CHANGED.

6,000 RPM) IN COLD WEATHER CONDITIONS BELOW 32 F (0 C). DTCS P0300:00, P0301:00 AND/OR P0302:00 ARE STORED IN MEMORY. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO. 1 MISFIRE DETECTED P0302:00: CYLINDER NO. 2 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. THE PCM MAY DETECT A FALSE MISFIRE UNDER THE SUBJECT CONDITIONS AND MAY FALL INTO FAIL SAFE MODE. TO ELIMINATE THIS CONCERN, THE PCM CONTROL LOGIC HAS BEEN CHANGED.

PROBLEM) STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. NOTE:THE ODOMETER WILL DISPLAY F0-002 DURING TRANSPORT MODE (ROOM FUSE 15A REMOVED). TRANSPORT MODE IS CANCELED WHEN ROOM FUSE 15A IS INSTALLED OR THE VEHICLE ODOMETER IS MORE THAN 12.4MI (20KM).

THE LEFT (B) AND/OR RIGHT (C) REMOTE HANDLES. ALSO, THE SEATBACKS MAY NOT FULLY LATCH (LOCK) WHEN PLACED IN THE UPRIGHT POSITION.THIS CONCERN MAY BE CAUSED BY EITHER OF THE FOLLOWING:INSUFFICIENT REMOTE CABLE TENSION DUE TO INCORRECT ADJUSTMENT POSITION (A) OF THE REMOTE CABLE.THE CABLE BALL (B) GETS SEIZED ON SHARP EDGES INSIDE THE CYLINDER.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

EXPERIENCING POOR ENGINE PERFORMANCE OR MISFIRE (MITSUBISHI PCM ONLY).THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM THAT MAY DETECT FALSE ERROR OF THE A/F SENSOR, RESULTING IN FALSE DETECTION OF P0421. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.CATALYST MON-ITOR FUNCTION EXPLANATIONTHE PCM MONITORS THE OXYGEN STORAGE AMOUNT PROPORTIONAL TO CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC.THE PCM STARTS TO MONITOR AFTER RECOVERY (FUEL INJECTION STARTS) FROM FUEL CUT CONTROL.THE PCM TEMPORARILY CHANGES THE TARGET AIR/FUEL RATIO TO RICH AT FUEL CUT RECOVERY, AND DETECTS THE RESPONSE TIME UNTIL THE HO2S OUTPUT SIGNAL OUTPUTS THE VOLTAGE ON THE RICH SIDE. IF THE CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC DETERIORATES, THE AMOUNT OF THE TIME UNTIL THE HO2S DETECTS THE VOLTAGE ON THE RICH SIDE IS SHORTER COMPARED TO THE NORMAL PURIFICATION CHARACTERISTIC AS SHOWN. THE PCM DETECTS A CATALYTIC CONVERTER MALFUNCTION USING THIS CHARACTERISTIC.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6).TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

FAHRENHEIT / 0 DEGREES CELSIUS), SOME VEHICLES MAY EXHIBIT A ROUGH IDLE AND/OR THE CHECK ENGINE LIGHT ON WITH ANY OF THE FOLLOWING DTC(S) STORED IN MEMORY.P0300 - RANDOM MISFIRE DETECTEDP0301 - CYLINDER NO.1 MISFIRE DETECTEDP0302 - CYLINDER NO.2 MISFIRE DETECTED P0303 - CYLINDER NO.3 MISFIRE DETECTED P0304 - CYLINDER NO.4 MISFIRE DETECTED THIS MAY BE CAUSED BY FROZEN WATER ACCUMULATED IN THE MAIN SILENCER, RESTRICTING EXHAUST FLOW.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

MISFIRE RELATED DTCS OF P0300:00, P0301:00, P0302:00, P0303:00 AND P0304:00. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE IGNITION COIL(S) DUE TO A HIGH DIFFERENCE BETWEEN COLD AND WARM AMBIENT TEMPERATURES. THE PRODUCTION METHOD OF THE IGNITION COIL HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.

BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT.

AND P0203.NOTE:ENGINE MISFIRE RELATED DTCS (P0301, P0302, P0303, P0304) ARE USUALLY STORED AT THE SAME TIME.P0201:00: FUEL INJECTOR CIRCUIT/OPEN CYLINDER NO.1P0202:00: FUEL INJECTOR CIRCUIT/OPEN CYLINDER NO.2P0203:00: FUEL INJECTOR CIRCUIT/OPEN CYLINDER NO.3P0204:00: FUEL INJECTOR CIRCUIT/OPEN CYLINDER NO.4THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE PCM (DENSO PRODUCED ONLY). TO CORRECT THE CONCERN, THE PCM INTERNAL FAILURE HAS BEEN ELIMINATED.

THE UNIQUE OIL FILTER CAN BE IDENTIFIED WITH TWO WHITE BANDS AS SHOWN BELOW.

FAHRENHEIT / 0 DEGREES CELSIUS), SOME VEHICLES MAY EXHIBIT A ROUGH IDLE AND/OR THE CHECK ENGINE LIGHT ON WITH ANY OF THE FOLLOWING DTC(S) STORED IN MEMORY.P0300 - RANDOM MISFIRE DETECTEDP0301 - CYLINDER NO.1 MISFIRE DETECTEDP0302 - CYLINDER NO.2 MISFIRE DETECTED P0303 - CYLINDER NO.3 MISFIRE DETECTED P0304 - CYLINDER NO.4 MISFIRE DETECTED THIS MAY BE CAUSED BY FROZEN WATER ACCUMULATED IN THE MAIN SILENCER, RESTRICTING EXHAUST FLOW.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

MISFIRE RELATED DTCS OF P0300:00, P0301:00, P0302:00, P0303:00 AND P0304:00. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE IGNITION COIL(S) DUE TO A HIGH DIFFERENCE BETWEEN COLD AND WARM AMBIENT TEMPERATURES. THE PRODUCTION METHOD OF THE IGNITION COIL HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.

MISFIRE RELATED DTCS OF P0300:00, P0301:00, P0302:00, P0303:00 AND P0304:00. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE IGNITION COIL(S) DUE TO A HIGH DIFFERENCE BETWEEN COLD AND WARM AMBIENT TEMPERATURES. THE PRODUCTION METHOD OF THE IGNITION COIL HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6). TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738).P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONP0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.NOTE:IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.

HIGHER.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6)TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

MISFIRE RELATED DTCS OF P0300:00, P0301:00, P0302:00, P0303:00 AND P0304:00. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE IGNITION COIL(S) DUE TO A HIGH DIFFERENCE BETWEEN COLD AND WARM AMBIENT TEMPERATURES. THE PRODUCTION METHOD OF THE IGNITION COIL HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6). TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738).P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONP0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.NOTE:IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.

BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT

HIGHER.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6).TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING 2 SYMPTOMS, EVEN THOUGH THE WINDSHIELD IS CLEAR. LANE DEPARTURE WARNING SYSTEM (LDWS) WARNING LIGHT TURNS ON AT IDLE; DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY. ADAPTIVE LED HEADLIGHTS (ALH) WARNING LIGHT TURNS ON WHILE DRIVING; DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY.

SOME CUSTOMERS MAY COMPLAIN THAT THE FRONT POWER (DRIVER AND/OR PASSENGER) SEATS DO NOT SLIDE BACK AND FORTH PROPERLY OR THAT THEY MAY BE COMPLETELY INOPERATIVE. THIS CONCERN MAY BE CAUSED BY A FOREIGN OBJECT GETTING STUCK UNDER THE POWER SLIDE UNIT (BELOW) WHILE IN OPERATION. THIS CAN CAUSE MOTOR MOUNTING BRACKET (A) DEFORMATION, RESULTING IN MOTOR CABLE (B) BREAKAGE.

Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with an active SAT radio.

screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White dots

cracking This may be caused by a faulty center display

There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Please use the table below when ordering the screen repair kits. This can also be found in Service Alert SA-041/22.

Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] * B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] * No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. * In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). * In other cases this DTC might be found without a related customer concern. NOTE: In most cases, no dealer visit is necessary.

cracking This may be caused by a faulty center display.

possible due to continuous reboot.

Mazda is aware of the issue and is working on a resolution. This Service Alert will be updated with the newest repair information as it becomes available.

No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. 6 Bluetooth device will not pair No. 7 Incorrect GPS position No. 8 Voice Recognition Does Not Work No. 9 Cannot Make a Hands-Free Call No. 10 Cannot Play Bluetooth Audio No. 11 Other Symptoms No. 12 How to update the Navigation SD Card Map No. 13 How to Check Navi SD Card VIN Lock

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.230 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software. Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

This may be caused by an incorrect clock GPS Sync setting.

All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.

All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.

/ Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions

When the concern occurs, MAZDA CONNECT reboots repeatedly, and if the SD card is removed during this reboot cycle, the rebooting cycle ends. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error. To correct the concern, the SD card hardware has been changed.

Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles], B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles build on or before March 2, 2019], No DTC - Gen 7 vehicles built after March 2, 2019, DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

/ Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions

Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature.

All Mazda connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin.

This may be caused by an aftermarket accessory device.

Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. If swapped, the SD card that is installed into the other vehicle becomes linked to the VIN of that vehicle.

Navigation voice guidance will skip and cut out losing many words.Pandora will suddenly disconnect and MAZDA CONNECT will revert to the previously used source. If you encounter a vehicle with these issues, DO NOT attempt any repairs on the vehicle. There is nothing wrong with the vehicle. This is an issue with the Pandora APP. Have the customer contact Pandora at pandora-support@pandora.com. NOTE: If the Pandora APP works on the customer's phone, they can stream Pandora using Bluetooth.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.

CarPlay / Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS - Infotainment - MAZDA CONNECT Updates - Apple Carplay / Android Auto MDARS Activation Instructions

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update.

The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the SD card hardware has been changed.

The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the SD card hardware has been changed.

This may be caused by an incorrect clock GPS Sync setting.

of view B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.

Audio System, Bluetooth, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux Voice Command, How to Check Navi SD Card VIN Lock.

Use the troubleshooting chart below to repair the vehicle.

Use the troubleshooting chart below to repair the vehicle.

This may be caused by an incorrect clock GPS Sync setting.

B14F0:92 - General temporary failure in forward sensing camera (FSC). DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details. If the vehicle has this DTC, DO NOT replace the FSC. Read below.

NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software.Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

Use the flowchart below to repair the vehicle.

Many frequently asked question and the answers.

Use the flowchart below to repair the vehicle.

aha/Pandora/Stitcher/Bluetooth and the same device is also connected to the USB port for charging. The concerns may include: Blank Screen and/or No Audio Sound, Phone will not charge.Blank Screen and/or No Audio Sound These concerns may be caused by:The MAZDA CONNECT system has reached its capacity limits when streaming music with audio source aha/Pandora/Stitcher/Bluetooth and also connected to the USB port.The MAZDA CONNECT system has reached its capacity limits when the customer's USB device capacity exceeds 16 GB (e.g. 64 GB iPhone X). The MAZDA CONNECT system USB port capacity is 16 GB (FAT32).Mazda recommends not to connect any devices to the USB port when streaming music with audio source aha/Pandora/Stitcher/Bluetooth. When streaming music with audio source aha/Pandora/Stitcher/Bluetooth (without USB connection), the Connectivity Master Unit (CMU) is able to process Bluetooth digital data (A) and output audio sound and display Bluetooth audio information. If the same device is connected to the USB port for charging, the CMU processes both Bluetooth digital data (A) and USB digital data (B) from the same device at the same time. In this case, CMU resources may be exceeded, causing a Blank Screen and/or No Audio Sound.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement. NOTE: Always check for a TSB that may modify or eliminate prior authorization for a specific symptom for a given component.

for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active working SAT radio.

This is caused by a navigation map supplier software change. Customers can set preferences if needed. Example: A customer may have a Shell Gas Card and is only interested in Shell Gas Stations. The customer can set preference to only show Shell gas stations.

Use the flowchart below to repair the vehicle.

This is a normal condition. Album art and artist biographies are not provided by SiriusXM Satellite Radio, a blank white square frame is shown in place of the album art. Note: This information is also available at www.mazdahandsfree.com>FAQ>ENTERTAINMENT - SIRIUSXM. STATION LOGO SIRIUSXM satellite radio hardware is in the Tuner and Amp Unit (TAU). The station logo is not shown in the center display because there is no visual data communication cable between the TAU and the Connectivity Master Unit (CMU). A blank white square frame is shown in place of the station logo. Do NOT perform any repairs for these concerns.

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin.Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.100A or later). NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.

Use the flowchart below to repair the vehicle.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda's continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDACONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software. Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.

Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement. NOTE: Always check for a TSB that may modify or eliminate prior authorization for a specific symptom for a given component.

for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active (working SAT radio).

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.

The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during extremely cold temperatures. To correct the concern, the SD card hardware has been changed.

To resolve this concern, after the installation of the new CMU, check the software version.

aha/Pandora/Stitcher/Bluetooth and the same device is also connected to the USB port for charging. The concerns may include: Blank Screen and/or No Audio Sound, Phone will not charge, Blank Screen and/or No Audio Sound

The cracks are internal and cannot be felt by touch. This may be caused by a faulty center display.

This is a normal condition.

This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.

NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda's continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.

The concern occurs when the interior of the vehicle is cold and disappears when the interiorwarms up. This is caused by some for the MAZDA CONNECT navigation system SD cards beingmanufactured with improper hardware, resulting in a data reading error during cold temperatures. To correctthe concern, the SD card hardware has been changed.

This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping.The navigation SD card has a malfunction.

This is caused by the damper coming off the speaker frame due to corrosion. To correct the issue, a plating process was added at the supplier beginning on November 13, 2015.

part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.

59.00.502or later).NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tabin MAZDA CONNECT Settingsbefore performing the update.

DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.

MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux, Voice Command

NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update.

This is caused by the damper coming off the speaker frame due to corrosion on the speaker back frame. To correct the issue, a plating process was added at the supplier beginning on November 13, 2015.

part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502or later). NOTE: For CX-9 with version earlier than 59.00.441, the tachometer function has been removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software.

MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. This concern may be a normal operation of the CMU connecting to available devices on start up.

SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT.

TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750). EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750. NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT. SYSTEM DOES NOT RECOGNIZE USB/SD CARD. SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT. WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT. FAVORITES DISAPPEAR. VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH. REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN. TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE. WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCATION IS COMMA. CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE. NOTE: MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE,AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VERSION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT. SYSTEM DOES NOT RECOGNIZE USB/SD CARD. SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT. WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT. FAVORITES DISAPPEAR. VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH. REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN. TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE. WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCATION IS COMMA. CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE. NOTE: MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VERSION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

FOR ALL VEHICLES: NAVIGATION OR OTHER SCREEN FREEZES OR REBOOTS. SYSTEM DOES NOT RECOGNIZE USB/SD CARD. SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT. WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT. NAVIGATION TURNS TO A BLACK SCREEN. FAVORITES DISAPPEAR. VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH. REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN. TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE. WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCATION IS COMMA.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

DIFFERENT SONG WILL PLAY.IF THE CUSTOMER SELECTS A DIFFERENT SONG, MOST OF THE TIME IT WILL CONTINUE PLAYING THE CURRENT SONG.IF THE CUSTOMER SHOULD SELECT THE CURRENT SONG AGAIN, IT MAY START PLAYING A DIFFERENT SONG.

TO IMPROVE THE HANDLING OF BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.CUSTOMERS EXPERIENCING RELATED CONCERNS SHOULD HAVE THEIR VEHICLE AND/OR DEVICE INSPECTED ACCORDING TO THE FOLLOWING PROCEDURE.

PART OF THE NEW CAR READY STEP 3 PROCESS. MAKE SURE THE NEW VEHICLE SPECIALIST RECEIVES A COPY OF THIS BULLETIN.SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 55.00.760 OR LATER).SOME STREET NAMES IN CANADA ARE NOT DISPLAYED.NAVIGATION DOES NOT ALLOW TO SET CERTAIN CITIES AS DESTINATION.NAVIGATION DOES NOT ANNOUNCE VOICE GUIDANCE FOR STREET NAMES.NAVIGATION TURNS TO A BLACK SCREEN REMAINING THE TASK BAR.TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750).EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750.NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT.SYSTEM DOES NOT RECOGNIZE USB/SD CARD.SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT.WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT.FAVORITES DISAPPEAR.VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH.REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN.TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE.WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCA-TION IS COMMA.CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE.NOTE:MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VER-SION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

APPEARANCE CONCERN.PROTECTIVE TAPE HAS BEEN ADDED TO THE AUDIO PANEL TO ELIMINATE THIS CONCERN.

56.00.760 OR LATER).SOME STREET NAMES IN CANADA ARE NOT DISPLAYED.NAVIGATION DOES NOT ALLOW TO SET CERTAIN CITIES AS DESTINATION.NAVIGATION DOES NOT ANNOUNCE VOICE GUIDANCE FOR STREET NAMES.NAVIGATION TURNS TO A BLACK SCREEN REMAINING THE TASK BAR.TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750).EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750.NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT.SYSTEM DOES NOT RECOGNIZE USB/SD CARD.SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT.WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT.FAVORITES DISAPPEAR.VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH.REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN.TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE.WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCA-TION IS COMMA.CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE.NOTE:MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VER-SION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

CONNECT.NAVIGATION VOICE GUIDANCE WILL SKIP AND CUT OUT LOSING MANY WORDS.PANDORA WILL SUDDENLY DISCONNECT AND MAZDA CONNECT WILL REVERT TO THE PREVIOUSLY USED SOURCE. IF YOU ENCOUNTER A VEHICLE WITH THESE ISSUES, DO NOT ATTEMPT ANY REPAIRS ON THE VEHICLE. THERE IS NOTHING WRONG WITH THE VEHICLE. THIS IS AN ISSUE WITH THE PANDORA APP. HAVE THE CUSTOMER CONTACT PANDORA AT PANDORA-SUPPORT@PANDORA.COM. NOTE: IF THE PANDORA APP WORKS ON THE CUSTOMER'S PHONE, THEY CAN STREAM PANDORA USING BLUETOOTH.

THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

PHONE CALLS WHEN THE SMARTPHONE IS PAIRED WITH A VEHICLE OR WIRELESS HEADSET. THE ISSUE EXTENDS TO GPS VOICE NAVIGATION FOR SOME, BUT STREAMING MUSIC OVER BLUETOOTH APPEARS TO BE UNAFFECTED. SPECIFICALLY, DOZENS OF USERS IN THE APPLE SUPPORT COMMUNITIES AND MACRUMORS DISCUSSION FORUMS CLAIM TO BE EXPERIENCING DISTORTED, STATICKY, OR INAUDIBLE PHONE CALLS WHEN USING AN IPHONE SE. IF YOU EXPERIENCE A CUSTOMER COMPLAINT, AND THE CUSTOMER HAS A NEW IPHONE SE, DO NOT REPLACE ANY PARTS ON THE VEHICLE. EXPLAIN TO THE CUSTOMER THAT THE IPHONE MAY BE THE PROBLEM. HAVE THE CUSTOMER VISIT THIS WEBSITE: HTTP://WWW.MACRUMORS.COM/2016/04/11/IPHONE-SE-BLUETOOTH-PHONE-CALL-AUDIO-ISSUES/

USE THIS VERSION FOR ALL MAZDA CONNECT UPDATES, INCLUDING OPEN SSP98 VEHICLES. IF SSP98 IS CLOSED, USE TSB 09-024/16 TO REPAIR THE VEHICLES.CLICK ON "IDS/INFOTAINMENT", THEN "MAZDA CONNECT UPDATES" TO DOWNLOAD IT. UPDATE YOUR USB DRIVES ACCORDING TO THE INSTRUCTIONS IN TSB 09-024/16.ALSO MAKE SURE TO SELECT "ALL FILES" FOR "SAVE AS TYPE:". IF LEFT AS "COMPRESSED (ZIPPED) FOLDER," THE FILE WILL BE SAVED AS A ".ZIP" NO MATTER WHAT YOU USE AS AN EXTENSION.ATTN: TECHNICIANS - BE SURE TO DOCUMENT THE SOFTWARE VERSION INSTALLED ON THE REPAIR ORDER AND INFORM YOUR WARRANTY ADMINISTRATOR TO PROVIDE THE INFORMATION IN THE REPAIR TEXT OF THE WARRANTY CLAIM.MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VERSION UPDATES CAN BE FOUND ON MS3.

55.00.760 OR LATER).SOME STREET NAMES IN CANADA ARE NOT DISPLAYED.NAVIGATION DOES NOT ALLOW TO SET CERTAIN CITIES AS DESTINATION.NAVIGATION DOES NOT ANNOUNCE VOICE GUIDANCE FOR STREET NAMES.NAVIGATION TURNS TO A BLACK SCREEN REMAINING THE TASK BAR.TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750).EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750.NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT.SYSTEM DOES NOT RECOGNIZE USB/SD CARD. SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT.WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT.FAVORITES DISAPPEAR.VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH.REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN.TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE.WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCA-TION IS COMMA.CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE.NOTE:MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VER-SION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

CONNECT.NAVIGATION VOICE GUIDANCE WILL SKIP AND CUT OUT LOSING MANY WORDS.PANDORA WILL SUDDENLY DISCONNECT AND MAZDA CONNECT WILL REVERT TO THE PREVIOUSLY USED SOURCE. IF YOU ENCOUNTER A VEHICLE WITH THESE ISSUES, DO NOT ATTEMPT ANY REPAIRS ON THE VEHICLE. THERE IS NOTHING WRONG WITH THE VEHICLE. THIS IS AN ISSUE WITH THE PANDORA APP. HAVE THE CUSTOMER CONTACT PANDORA AT PANDORA-SUPPORT@PANDORA.COM. NOTE: IF THE PANDORA APP WORKS ON THE CUSTOMER'S PHONE, THEY CAN STREAM PANDORA USING BLUETOOTH.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section once a part is selected. Accessories E-catalog For models prior to 2016: Accessory Parts and Installation Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method A. Auxiliary Key Trace Cut Method If only one auxiliary key is lost/missing, some key cutting machines can trace cut a new key blank. 1. Trace cut the new auxiliary key blank(s). B. Auxiliary Key Code Cut Method If both auxiliary keys are lost/missing, use this method for cutting new auxiliary key blank(s). 1. Confirm you have access to a Mazda approved key cutting machine. See Mazda Approved Key Cutting Machine table.

A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

Follow the repair procedure below to repair the vehicle until the information is added.

This may be caused by loose rear spoiler installation nuts.

seat back surface.Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.

https://ecatalog.mazdausa.com

Follow the repair procedure below to repair the vehicle until the information is added to the Workshop Manual.

for download.

https://ecatalog.trademotion.com/

license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the resetting tool.

Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.

DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.

CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the resetting tool.

seat back surface.

This may be caused by loose rear spoiler installation nuts.

THE NOISE MAY BE CAUSED BY A REAR DIFFERENTIAL BEARING FAILURE.

SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.

THE REAR CONSOLE LID LATCH MAY BE BROKEN BY EXCESSIVE FORCE APPLIED TO THE LID. TO ELIMINATE THIS CONCERN, THE SHAPE OF THE REAR CONSOLE LID LATCH HAS BEEN CHANGED TO INCREASE ITS STRENGTH.

THE REAR CONSOLE LID LATCH MAY BE BROKEN BY EXCESSIVE FORCE APPLIED TO THE LID. TO ELIMINATE THIS CONCERN, THE SHAPE OF THE REAR CONSOLE LID LATCH HAS BEEN CHANGED TO INCREASE ITS STRENGTH.

DTC C1001:92 SETS AS A PAST RECORD FOR LOW VISIBILITY OF THE FORWARD SENSING CAMERA (FSC). IT DOES NOT MEAN THERE IS AN ACTUAL FSC DEFECT. IN SOME CASES THE CUSTOMER MAY HAVE A CONCERN WITH THE LANE DEPARTURE WARNING SYSTEM (LDWS) AND/OR HIGH BEAM CONTROL SYSTEM (HBC). IN OTHER CASES THIS DTC MIGHT BE FOUND WITHOUT A RELATED CUSTOMER CONCERN.

FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.

SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.

FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.

SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE: DO NOT paint ground point (3) attachment bolt (4) is seated. NEWLY INSTALLED FRONT FENDER STAY NOTE: CAUTION: If the bolt (4) contact area (3) is painted when the front fender stay (2) is newly replaced, it could cause a malfunction in the PCM. Before painting a newly replaced part, protect the bolt (4) contact area (3) with masking tape (5) as shown in the figure.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.

This is caused by a failure in the ambient temperature sensor. To correct this issue, the ambient temperature sensor has been modified.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a good know terminal.To measure the voltage/resistance avoiding any terminal damage.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc.) placed on the front passenger's seat.

data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage.

Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all auxiliary keys are lost.

data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. Customers concern can be resolved by sanding off paint at ground point (3) where attachment bolt (4) is seated. After installing the bolt (4), apply touch-up paint to the exposed base material area of the front fender stay.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.

notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.

On July 12th, 2018, Mazda Technical Services sent out an email extending the Mazda Diagnostic Reprogramming Tool (MDRT) service loaner program for Special Service Program (SSPA6) for an additional 7 months to improve the low completion rate for campaign SSPA6. As previously advised the MDRT Tool loaner software is expiring at the end of February 2019. New MDRT tools are being prepared to reprogram the Airbag Control Module for those vehicles that remain unrepaired. These tools will replace the MDRT currently at your dealership for this SSP. Action required: All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by February 28, 2019. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge.

On July 12th, 2018, Mazda Technical Services sent out an email extending the Mazda Diagnostic Reprogramming Tool (MDRT) service loaner program for Special Service Program (SSPA6) for an additional 7 months to improve the low completion rate for campaign SSPA6. As previously advised the MDRT Tool loaner software is expiring at the end of February 2019. New MDRT tools are being prepared to reprogram the Airbag Control Module for those vehicles that remain unrepaired. These tools will replace the MDRT currently at your dealership for this SSP. Action required: All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by February 28, 2019. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge.

If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps):CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery's Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda GR8-1291, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.

notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed. This TSB is applicable for the following cases. The oil change due notification does not come on, even after mileage exceeded 10,000 miles. Oil life in the center display is still less than 40% even though the mileage exceeded 7,000 miles. To display "Flexible" setting and "Oil life" on the center screen, select the "Applications" screen, "Maintenance", then "Oil Change" tab. For complete details, refer to the the instructions on MGSS (MAINTENANCE MONITOR OPERATION PROCEDURE).

OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc.) placed on the front passenger's seat.

initialization was not performed correctly before customer delivery.TPMS INITIALIZATION PROCESS: When any of the services below is performed, BE SURE TO INITIALIZE THE TPMS BEFORE DRIVING THE VEHICLE by pushing and holding the TPMS Set Switch on the dash until the TPMS warning light flashes two times and the warning beep sounds once. The TPMS must be initialized in the following cases: 1. Tire pressures have been adjusted in one or more tires. 2. Tires have been rotated. 3. Tires or wheels have been replaced. 4. The vehicle's battery cable has been disconnected for any reason. 5. The vehicle's battery has been discharged. 6. The DSC HU/CM connector has been disconnected for any reason.

Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

Vehicle odometer under 62 miles ? VIN-lock occurs with key ON for 3 minutes or longer. 2. Vehicle odometer over 62 miles ? VIN-lock occurs at key ON. Navigation SD Card Map Update Note: Mazda Toolbox navigation SD card map update can only be performed on a navigation SD card that is VIN-locked. See VIN-lock procecure below.

?Turn signal malfunction and 5 or more warning lights illumination. ?Some warning lights illumination The front passenger seat harness (A) may be damaged by internal seat frame (B) weld spatter. Image below shows possible area of weld spatter (C).

(M-MDS) may display a value of only 1/100th of the actual resistance value. This is caused by improper SAS control unit software. To eliminate this from occurring in the future, the SAS control unit software has been modified.

if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No. 2 (C) socket covers have not been correctly installed or are missing due to improper prior repairs (i.e., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, HID module seal (D), or missing bumper brackets (E) is not covered by warranty policy.

When you encounter a customer with this concern, first verify the condition when the customer noticed this symptom. If the condition is similar to the following "CONTROL LOGIC OF AMBIENT TEMPERATURE" or "DIFFERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS", advise the customer that this is a normal characteristic of the vehicle and not a malfunction. If the condition does not meet the following and the sensor malfunction is suspected, make sure to inspect the sensor according to MGSSonline or Workshop Manual (section 09-22 AMBIENT TEMPERATURE SENSOR INSPECTION). Replace the sensor only when it fails the Workshop Manual inspection.

prevent the battery from discharging.

Operations is 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

Forward Sensing Camera (FSC) and Laser Sensor. Replace the windshield with a new one instead.

(M-MDS) may display a value of only 1/100th of the actual resistance value. This is caused by improper SAS control unit software. To eliminate this from occurring in the future, the SAS control unit software has been modified.

THE TEST KIT IS DESIGNED PECIFICALLY FOR SKYACTIV MODULE TERMINALS. THE SST WILL BE SHIPPED BY MAZDAS TOOL VENDOR BOSCH STARTING JANUARY 15, 2016. PROCEDURES FOR USAGE ARE FOUND IN THE SKYACTIV WIRING TERMINAL TEST KIT WBT, COURSE #1649. THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST:

IS TURNED ON, AND WILL NOT REBOOT. IT WILL ONLY REBOOT AFTER THE IGNITION IS TURNED OFF AND THEN ON AGAIN. THIS IS CAUSED BY AN INTERNAL MALFUNCTION OF THE CONNECTIVITY MASTER UNIT (CMU) HARDWARE. NOTE: IF THE SYSTEM REBOOTS BY ITSELF, THIS TSB IS NOT APPLICABLE. REFER TO TSB 09-022/15 FOR CMU SOFTWARE UPDATE.

NOTIFICATION WILL NOT WORK BECAUSE OF IMPROPER CONTROL LOGIC OF THE PCM. THIS TSB IS APPLICABLE FOR THE FOLLOWING CASES. THE OIL CHANGE DUE NOTIFICATION DOES NOT COME ON, EVEN AFTER MILEAGE EXCEEDED 10,000 MILES. OIL LIFE IN THE CENTER DISPLAY IS STILL LESS THAN 40% EVEN THOUGH THE MILEAGE EXCEEDED 7,000 MILES. TO DISPLAY FLEXIBLE SETTING AND OIL LIFE ON THE CENTER SCREEN, SELECT THE APPLICATIONS SCREEN, MAINTENANCE, THEN OIL CHANGE TAB. FOR COMPLETE DETAILS, REFER TO THE MAINTENANCE MONITOR OPERATION PROCEDURE IN THE WORKSHOP MANUAL.

OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS.

(2) DOOR LOCKS REPEATEDLY LOCK AND UNLOCK WHEN APPROACHING THE VEHICLE WITH THE ADVANCED KEY. (3) KEY WARNING LIGHT (RED) ON WHILE DRIVING AND DTC B10D1:23 AND/OR B10D3:23 IS(ARE) STORED. B10D1:23 REQUEST SWITCH (LF) CIRCUIT MALFUNCTION B10D3:23 REQUEST SWITCH (RF) CIRCUIT MALFUNCTION

IF ALL THE BULB SOCKETS ARE PRESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET COVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.

IF NOT USED, THE CONTROL MODULE REPROGRAMMING MAY FAIL DUE TO A WEAK VEHICLE BATTERY.THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE PREVENTS THE VEHICLE BATTERY FROM BEING DISCHARGED. THIS ALLOWS THE IDS TO REPROGRAM A CONTROL MODULE WITHOUT INTERFERENCE FROM A WEAK OR UNDERCHARGED VEHICLE BATTERY. NOTE: CONTROL MODULE DAMAGE MAY OCCUR IF THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE IS NOT USED.

THIS MAY BE CAUSED BY AN OBSTRUCTION OF THE FRONT AND/OR REAR LIGHT SENSOR(S) (E.G. HANGING A PARKING PERMIT FROM THE MIRROR). USE A SOFT CLOTH WITH MILD DETERGENT TO CLEAN THE MIRROR. HARSH DETERGENT MAY DAMAGE THE FRONT AND/OR REAR LIGHT SENSOR(S).

IF AN AFTERMARKET ALARM SYSTEM IS INSTALLED, THE REAR HARNESS MIGHT HAVE RECEIVED DAMAGE FROM ELECTRO-TAP CONNECTORS (A) OR TO THE PROTECTOR TUBE (B). THIS DAMAGE IS NOT COVERED UNDER WARRANTY.

UNPLUG THE MODULE FOR AT LEAST 10 SECONDS.RECONNECT THE BATTERY, WAIT 60 SECONDS AND THEN HAVE THE CUSTOMER TRY THE APP AGAIN.IF THE VEHICLE STARTS, ORDER MODULE 0000-8F-Z80A.NOTE: THERE IS A LIMITED SUPPLY OF THE MODULE AT THIS TIME, THEREFORE ONLY USE THIS PART FOR THIS SPECIFIC CONDITION.DUE TO THE LIMITED SUPPLY, MAKE SURE YOU WERE SHIPPED THE A LEVEL PART AND NOT THE ORIGINAL PART BEFORE INSTALLING THE PART.INSTALL THE MODULE AND PROGRAM IT PER MMS PROGRAMMING INSTRUCTIONS.INSTRUCT THE CUSTOMER TO UPDATE THEIR ACCOUNT WITH THE NEW MODULE INFORMATION, OTHERWISE THE MMS WILL NOT WORK FROM THE APP.

SOME CUSTOMERS MAY COMPLAIN ABOUT AN INTERMITTENT NO CRANK/NO START. THIS MAY BE CAUSED BY INSTRUMENT PANEL WIRING HARNESS CONNECTOR C-11 NOT FULLY SEATED (LOCKED). IDS MAY SHOW SEVERAL U CODES STORED IN MEMORY. PROPERLY SECURE THE INSTRUMENT PANEL WIRING HARNESS CONNECTOR C-11 TO RESOLVE CUSTOMER COMPLAINT.

SOME VEHICLES MAY EXPERIENCE MAZDA CONNECT INFOTAINMENT SYSTEM SHUTTING DOWN WITH A FEW MINUTES AFTER IGNITION IS TURNED ON, AND WILL NOT REBOOT. IT WILL ONLY REBOOT AFTER IGNITION IS TURNED OFF AND THEN TURNED ON AGAIN. THIS IS CAUSED BY AN INTERNAL MALFUNCTION OF THE CONNECTIVITY MASTER UNIT (CMU) HARDWARE.

SOME VEHICLES MAY EXHIBIT BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THEHANDLING OF BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CREATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010. CUSTOMERS EXPERIENCING RELATED CONCERNS SHOULD HAVE THEIR VEHICLE AND/OR DEVICE INSPECTED ACCORDING TO THE FOLLOWING PROCEDURE.

To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.

This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.

The rearview mirror (1) rattles up and down (2) while adjusting the mirror. 2. The rearview mirror (1) makes a rattle noise depending on the road surface conditions while driving. This concern is caused during rearview mirror installation. The adhesive is squeezed out between the windshield and the mirror base. The rearview mirror is assembled on top of the overextended adhesive. The adhesive is softened by heat, and loosening screws, results in a rattling concern.

will need to be ordered and installed when replacing the differential. NOTE: The breather threads have a sealant and locking compound that prevents it from being reused. Refer to GEPC for the correct part number of the Differential Breather. The instructions on MGSS will be updated soon to include replacing the breather when replacing the differential with a new unit.

This may be caused by the sun's reflection.

This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

This may be caused by the sun's reflection.

This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below

end causing a poor appearance and obstructing the view of the back window.

will need to be ordered and installed when replacing the differential. NOTE: The breather threads have a sealant and locking compound that prevents it from being reused. Refer to GEPC for the correct part number of the Differential Breather. The instructions on MGSS will be updated soon to include replacing the breather when replacing the differential with a new unit.

This may be caused by the sun's reflection.

This is caused by the gripping force of the seaming welt being insufficient for frequent usage of the rear seat (vehicle used for ride sharing). No mass production change is planned.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

color) instead of athe conventional methanol type (blue color). This change is for European compliance Mazda has decided to make the change for all markets.

The lower portion of the trim may become distorted (as shown below) due to high temperatures. To eliminate this concern, the shape of the body flange has been improved during mass-production to allow sufficient A-pillar clearance.

Some customers may coimplain that the ventilator grille(s) are reflecting onto the closed front door window glass (around the outer mirror glass area) This is caused by light reflecting off of the bright vent grille. If this is causing a problem for customes, the bright type vent grilles can be replaced with black ones.

remedy, and warranty coverage (if applicable).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

This is caused by the cushion tape peeling off from the end(s) due to interference with the windshield and vehicle vibration (CX-5/Mazda6) or from the gap between the dashboard and the cushion tape because there there is no rib (1) at the dashboard ends (Mazda3). To prevent the tape from peeling off, both ends of the cushion tape are now folded over to the back side of the dashboard (CX-5/Mazda6) or stapled (Mazda3).

This concern only occurs on vehicles where the liftgate stay damper recall (9916H) was previously performed. Some of the liftgate stay damper rods used for the recall were chrome-plated, which is smooth and may cause a shortage of oil film to the stay damper rod. The squeak noise occurs due to the friction between the gas sealing and the damper rod when opening and/or closing the liftgate.

This is caused by the gripping force of the seaming welt being insufficient for frequent usage of the rear seat (vehicle used for ride sharing). No mass production change is planned.

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

of the windshield.This is caused by the cushion tape peeling off from the end(s) due to interference with the windshield and vehicle vibration. To prevent the tape from peeling off, both ends of the cushion tape are now folded over to the back side of the dashboard or stapled depending on the model.

This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may becaused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

This is caused by the gripping force of the seaming welt being insufficient for frequent usage of the rear seat (vehicle used for ride sharing). No mass production change is planned.

This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

remedy, and warranty coverage (if applicable).

This is caused when water (containing white corrosion) is generated inside the door mirror base (B), then drains down the door panel causing a poor appearance concern. The door mirror base was originally designed to drain water to the outside of the door. The shape of the door mirror base gasket has been modified to drain water to the inside of the door. Replacing the gasket should eliminate this concern.

lights are on when they start driving around dusk or dawn under low temperatures. At that time, the windshield is clear but the lens of the Forward Sensing Camera (FSC) is foggy. The FSC may not function properly under the following conditions: ? Foggy windshield ? Foggy FSC lens ? Heavy rain, dense fog, snow and direct sun light ? No or poor lane markings. When the FSC control system detects the foggy lens of the camera, the system deactivates LDWS and HBC functions.

This is found on vehicles equipped with power seats and leather, leatherette or cloth type seat trim. The front seat cushion is attached to the seat frame using a folding collar. The collar may slip out of the seat frame when force is applied to the front of the seat cushion.

lights are on when they start driving around dusk or dawn under low temperatures. At that time, the windshield is clear but the lens of the Forward Sensing Camera (FSC) is foggy. The FSC may not function properly under the following conditions: ? Foggy windshield ? Foggy FSC lens ? Heavy rain, dense fog, snow and direct sun light ? No or poor lane markings. When the FSC control system detects the foggy lens of the camera, the system deactivates LDWS and HBC functions.

other similar tools be used to hold the lift gate stay dampers. Use only the tools specified in the recall. Vice Grips or other similar tools can easily damage the stay dampers. NOTE: Stay damper parts received with Vice Grip marks will not be covered under warranty.

AN IMPROPER PRODUCTION PROCESS CAUSED REMAINING AIR TO BE TRAPPED BETWEEN THE GLASS AND THE INTERMEDIATE FILM. THE PRODUCTION PROCESS HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN.

THE PAINT IN THIS AREA MAY BE THINNER THAN NORMAL DUE TO PRODUCTION VARIANCES. THE PRODUCTION PROCESS HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN.

THIS IS CAUSED BY THE TOPPER RUBBER, A COMPONENT OF THE LIFTGATE LATCH AND LOCK ACTUATOR (A), HARDENING WHEN THE TEMPERATURE DROPS BELOW FREEZING. THE STOPPER RUBBER HAS NOW BEEN IMPROVED TO ELIMINATE THIS CONCERN.

THE LOWER PORTION OF THE TRIM MAY BECOME DISTORTED (AS SHOWN BELOW) DUE TO HIGH TEMPERATURES. TO ELIMINATE THIS CONCERN, THE SHAPE OF THE BODY FLANGE HAS BEEN IMPROVED DURING MASS-PRODUCTION TO ALLOW SUF-FICIENT A-PILLAR CLEARANCE.

THIS CONCERN IS MOST LIKELY TO BE FOUND IN A COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEEN THE PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH A HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE A HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED AREA TO REMOVE THE STAIN(S).

THE PAINT MAY BECOME DAMAGED BY WEATHERSTRIP CHAFING CAUSED BY LIFTGATE/TRUNK LID VIBRATION WHILE DRIVING. TO ELIMINATE THIS CONCERN ON CX-5, SILICONE IS APPLIED TO THE LIP OF THE WEATHERSTRIP TO REDUCE FRICTION AGAINST THE LIFTGATE.

THIS IS CAUSED BY THE STOPPER RUBBER, A COMPONENT OF THE LIFTGATE LATCH AND LOCK ACTUATOR (A), HARDENING WHEN THE TEMPERATURE DROPS BELOW FREEZING. THE STOPPER RUBBER HAS NOW BEEN IMPROVED TO ELIMINATE THIS CONCERN.

THE LOWER PORTION OF THE TRIM MAY BECOME DISTORTED (AS SHOWN BELOW) DUE TO HIGH TEMPERATURES. TO ELIMINATE THIS CONCERN, THE SHAPE OF THE BODY FLANGE HAS BEEN IMPROVED DURING MASS-PRODUCTION TO ALLOW SUF-FICIENT A-PILLAR CLEARANCE.

THIS IS CAUSED BY THE STOPPER RUBBER, A COMPONENT OF THE LIFTGATE LATCH AND LOCK ACTUATOR (A), HARDENING WHEN THE TEMPERATURE DROPS BELOW FREEZING. THE STOPPER RUBBER HAS NOW BEEN IMPROVED TO ELIMINATE THIS CONCERN.

SOME VEHICLES MAY EXHIBIT SMALL AIR BUBBLES AROUND UPPER LEFT CORNER OF WINDSHIELD. AN IMPROPER PRODUCTION PROCESS CAUSED REMAINING AIR TO BE TRAPPED BETWEEN GLASS AND THE INTERMEDIATE FILM. THE PRODUCTION PROCESS HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN.

THIS CONCERN IS MOST LIKELY TO BE FOUND IN COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEN PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED ARE TO REMOVE STAIN(S).

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plates surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plates surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.

when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plates surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plate's surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

The squeak noise may occur more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support.

This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.

If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot perform any additional testing of the system. Dealers and customers should never attempt to test or recreate crash scenarios under any circumstances because that could lead to an accident and injuries. NOTE: This article only applies to the applicable vehicles below equipped with SCBS system that uses a Laser Sensor. This article does not apply to newer vehicles equipped with SCBS system that uses a Forward Sensing Camera (FSC).

(replacement bulletin is shedule for release in Jan, 2017)

The squeak noise may occur more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support.

This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.

This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise. To eliminate this concern, the brake pad material has been changed in order to improve the rust-removing capability.

The squeak noise may occur more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support.

This concern is mostly found on new or low mileage vehicles, when the brakes are new. The grooves may be caused through abrasion from the accumulation of metal particles from the rear brake disc plates. The metal particles get caught between the brake pads and disc plates causing groove damage. To eliminate this concern, the disc plate surface honing process has been changed to reduce metal particle formation.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

The squeak noise may occur more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support.

vehicle service.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit. Tool Number Description Pricing PC1923MAZ Pro-Cut On-Car Brake Lathe Check eStore or call for current pricing OBTAINING TOOLS This tool can be ordered through Mazda eStore. You can log on to eStore at: http://dealers.mazdausa.com CUSTOMER SERVICE INFORMATION For warranty or product information contact Mazda Authorized Service Equipment at 877-768-6657. Customer service representatives are available from 7:30 AM until 7:00 PM CST, Monday through Friday. SPECIAL SERVICE TOOL (SST) PART NAME: OVERVIEW Pro-Cut On-Car Brake Lathe PART NUMBER: PC1923MAZ APPLICABLE MODELS: All USAGE: To machine brake rotors on the vehicle.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

1/2 to 4 inches (1 - 10 cm). The rattle noise may be caused by insufficient holding force of the glass run channel. To increase the holding force, the shape of glass run channel has been changed and non-woven pads have been attached to the glass run channel.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.

The noise may be caused by a rear shock absorber mounting bracket that is heavily corroded and broken. Due to insufficient durability of the bracket in certain environments, such as where road salt is used, corrosion and breakage can occur. To eliminate this concern, the material and the shape of the bracket (service parts) has been modified.

This may be caused by the dust boot having insufficient resistance to the cold. The shape and material of the dust boot has been changed to improve its resistance to cold.

properly initialize the system.The Tire Pressure Monitoring System (TPMS) monitors the tire pressure of all four tires indirectly using the data sent from the ABS wheel speed sensors. If the air pressure of one or more tires is too low compared with the specified value (the initial value learned by the system), the system warns the driver with the TPMS warning light in the instrument cluster and a beep sound. To allow the TPMS to operate correctly, it is essential that the TPMS be initialized to learn new conditions whenever a tire related service is performed.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare subject to denial or debit.

This may be caused by repeated load applied to the seat cushion (1) while the seat isoccupied. A section of the heater mat (2) just above the reinforcement rod (3) in the cushion pad contactsinternal heater mat wire and causes damage (4).

vehicle service.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

This may be caused by repeated load applied to the seat cushion (1) while the seat is occupied. A section of the heater mat (2) just above the reinforcement rod (3) in the cushion pad contacts internal heater mat wire and causes damage (4).

abnormal outer brake pad wear.The vehicle may also roll momentarily when starting from a stand-still with the EPB applied. This concern may be caused by the EPB not releasing completely. Modifications to the calipers have been made to eliminate this concern.

and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with a vehicle ahead is imminent. In addition, the system reduces damage in the event of a collision by operating the brake control when the system determines that a collision is unavoidable. It may also be possible to avoid a collision depending on the relative speed between your vehicle and the vehicle in front of you. In addition, when the driver depresses the brake pedal, the brakes are applied firmly and quickly to assist.

abnormal outer brake pad wear.The vehicle may also roll momentarily when starting from a stand-still with the EPB applied. This concern may be caused by the EPB not releasing completely. Modifications to the calipers have been made to eliminate this concern.

This may be caused by repeated load applied to the seat cushion (A) while the seat is occupied. A section of the heater mat (B) just above the reinforcement rod (C) in the cushion pad (A) contacts internal heater mat wire and causes damage (D).

IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.

1/2 TO 4 INCHES (1 - 10 CM). THE RATTLE NOISE MAY BE CAUSED BY INSUFFICIENT HOLDING FORCE OF THE GLASS RUN CHANNEL. TO INCREASE THE HOLDING FORCE, THE SHAPE OF GLASS RUN CHANNEL HAS BEEN CHANGED AND NON-WOVEN PADS HAVE BEEN ATTACHED TO THE GLASS RUN CHANNEL.

FOLLOWING A CHANGE TO THE SEAT WEIGHT SENSOR, URETHANE PADS WERE ADDED TO THE PASSENGER-SIDE SEAT CUSHION TO IMPROVE SEATING COMFORT. DUE TO THE ADDITION OF THE URETHANE PADS (WHICH WERE NOT INSTALLED ON THE DRIVER-SIDE SEAT), IT TAKES LONGER FOR THE PASSENGER-SIDE SEAT TO WARM UP.TO ELIMINATE THIS CONCERN, THE HEATER WATTAGE FOR THE PASSENGER-SIDE SEAT WARMER HAS BEEN INCREASED. ALSO, THE COUPLER, BOX (SEAT WARMER CONTROL UNIT) HAS BEEN CHANGED TO COPE WITH THE INCREASED WATTAGE.

1/2 TO 4 INCHES (1 - 10 CM).THE RATTLE NOISE MAY BE CAUSED BY INSUFFICIENT HOLDING FORCE OF THE GLASS RUN CHANNEL. TO INCREASE THE HOLDING FORCE, THE SHAPE OF GLASS RUN CHANNEL HAS BEEN CHANGED AND NON-WOVEN PADS HAVE BEEN ATTACHED TO THE GLASS RUN CHANNEL.

THIS CONCERN MAY BE DUE TO A SHORT IN THE SUNROOF SWITCH (A) CAUSED FROM CONDEN-SATION GENERATED BETWEEN THE ROOF PANEL AND THE SEAL. TO ELIMINATE THIS CONCERN IN THE FUTURE, A PROTECTIVE FILM HAS BEEN INSTALLED TO THE SWITCH AND A PAD INSTALLED TO THE HARNESS.

THE OWNER'S MANUAL PROVIDES 7 EXAMPLES: OBJECTS ON THE ROAD AT THE ENTRANCE TO A CURVE.VEHICLES PASSING IN THE OPPOSITE LANE WHILE MAKING A CURVE.METAL OBJECTS, BUMPS, OR PROTRUDING OBJECTS ON THE ROAD.WHEN PASSING THROUGH A TOLL GATE.WHEN PASSING UNDER A VINYL CURTAIN OR FLAG.PLASTIC OBJECTS SUCH AS PYLONS.TWO-WHEELED VEHICLES, PEDESTRIANS, ANIMALS OR STANDING TREES.THIS M-TIP ARTICLE PROVIDES 2 ADDITIONAL EXAMPLES:A. THERE IS FOGGING ON THE INNER SURFACE OF THE WINDSHIELD.B. THERE IS/ARE FOGGING/WATER DROPS ON THE OUTER SURFACE OF THE WINDSHIELD.THE NEAR INFRARED LASER BEAM IS A LIGHT BEAM AND IS REFRACTED BY WATER DROPS OR FOREIGN MATERIAL ON THE WINDSHIELD. IN THIS CASE, THE NEAR INFRARED LASER BEAM MAY NOT DETECT AN OBSTRUCTION AHEAD CORRECTLY.

THIS MAY BE CAUSED WHEN THE ELECTRONIC PARKING BRAKE (EPB) DOES NOT RELEASE COMPLETELY. TO ELIMINATE THIS CONCERN, THE EPB CONTROL MODULE LOGIC HAS BEEN MODIFIED.

1/2 TO 4 INCHES (1 - 10 CM).THE RATTLE NOISE MAY BE CAUSED BY INSUFFICIENT HOLDING FORCE OF THE GLASS RUN CHANNEL. TO INCREASE THE HOLDING FORCE, THE SHAPE OF GLASS RUN CHANNEL HAS BEEN CHANGED AND NON-WOVEN PADS HAVE BEEN ATTACHED TO THE GLASS RUN CHANNEL.

THIS CONCERN MAY BE DUE TO A SHORT IN THE SUNROOF SWITCH (A) CAUSED FROM CONDEN-SATION GENERATED BETWEEN THE ROOF PANEL AND THE SEAL. TO ELIMINATE THIS CONCERN IN THE FUTURE, A PROTECTIVE FILM HAS BEEN INSTALLED TO THE SWITCH AND A PAD INSTALLED TO THE HARNESS.

IF THE VEHICLE IS DELIVERED TO THE CUSTOMER WITH INCOMPLETE EPB SERVICE, THE CUSTOMER MAY EXPERIENCE IMPROPER OPERATION OF THE EPB SYSTEM.WHEN THE ELECTRIC PARKING BRAKE IS OPERATED/RELEASED, THE ELECTRIC PARKING BRAKE CONTROL MODULE PERFORMS AUTOMATIC ADJUSTMENT OF THE EPB AND DIAGNOSIS OF EPB SYSTEM.NOTE: IF ANY WARNING LIGHT IS ON AFTER OPERATING THE EPB SWITCH, REFER TO WORKSHOP MANUAL TROUBLESHOOTING.

THE OWNER'S MANUAL PROVIDES 7 EXAMPLES: OBJECTS ON THE ROAD AT THE ENTRANCE TO A CURVE.VEHICLES PASSING IN THE OPPOSITE LANE WHILE MAKING A CURVE.METAL OBJECTS, BUMPS, OR PROTRUDING OBJECTS ON THE ROAD.WHEN PASSING THROUGH A TOLL GATE.WHEN PASSING UNDER A VINYL CURTAIN OR FLAG.PLASTIC OBJECTS SUCH AS PYLONS.TWO-WHEELED VEHICLES, PEDESTRIANS, ANIMALS OR STANDING TREES.THIS M-TIP ARTICLE PROVIDES 2 ADDITIONAL EXAMPLES:A. THERE IS FOGGING ON THE INNER SURFACE OF THE WINDSHIELD.B. THERE IS/ARE FOGGING/WATER DROPS ON THE OUTER SURFACE OF THE WINDSHIELD.THE NEAR INFRARED LASER BEAM IS A LIGHT BEAM AND IS REFRACTED BY WATER DROPS OR FOREIGN MATERIAL ON THE WINDSHIELD. IN THIS CASE, THE NEAR INFRARED LASER BEAM MAY NOT DETECT AN OBSTRUCTION AHEAD CORRECTLY.

essential to first classify the issue into one of three primary categories: Noise, Vibration, or Harshness. Many customer complaints may involve overlapping symptoms, such as both noise and vibration, so identifying the dominant characteristic is critical. Once the primary symptom is determined, follow the appropriate diagnostic path. For example, if a concern includes both noise and vibration but is related to vehicle speed, the vibration diagnostic path should be followed. When considering component replacement during the diagnostic process, it is best practice to start with the lowest cost or most accessible part unless diagnostic evidence clearly identifies a more expensive or complex component as the root cause. This approach helps minimize repair costs and avoids unnecessary part replacements. For example, a growling or bearing whine noise may be mistakenly attributed to internal components in the differential, transfer unit, or transmission, when the actual source is a wheel bearing. Misdiagnosis like this can lead to unnecessary repairs, added time and cost. To help prevent this, always follow the guidelines in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.

Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.

The system performance has been improved as follows: Ver. 74.00.324 fixes these software errors (bugs): * If the shift lever is operated quickly while displaying the CarPlayTM screen, the rear view screen may not return to the CarPlayTM screen. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into the R position.

Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

configuration.

As the vehicle mileage increases, the ATF color changes. The color change does not affect vehicle performance.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Use a clean towel damped in leather/vinyl cleaner or mild soap to clean the steering wheel. NOTE: Upholstery maintenance and care information can also be found in the Owner's Manual.

This concern may be caused when a load, which is applied to the seat during braking, exceeds a certain level that could impact the retaining mechanism of the seat lifter causing the seat to gradually move downward. To eliminate this concern, the play in the lift mechanism gears has been reduced.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

The noise: Depends on the vehicles speed only (the more speed, the more noise) Occurs with all types of driving (acceleration, deceleration, steady speed) Does not depend on rpm, gear, or ATF temperature

bump when accelerating after deceleration at 25-40 mph (40-65 km/h) Hard to shift into 3rd, 4th, 5th, and/or 6th gear Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.

and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order to re-install the original plug from the old transmission.

This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and right side for RHD vehicle). NOTE: The noise will not occur if the steering wheel is in the center or to the full passenger-side position. The noise is caused when the edge (A) of the inner ball joint (B) gets stuck with the steering gear housing (C).

NOTE: The following Caution is included with every ATX that requires configuration.

Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the oil cooler was missing altogether. IMPORTANT NOTE: ALWAYS REMEMBER TO INCLUDE THE ORIGINAL OIL COOLER WITH THE RETURNED TRANSMISSION CORE!

when accelerating after deceleration at 25-40 mph (40-65 km/h), Hard to shift into 3rd, 4th, 5th, and/or 6th gear, Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.

of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

The noise: Depends on the vehicles speed only (the more speed, the more noise)Occurs with all types of driving (acceleration, deceleration, steady speed)Does not depend on rpm, gear, or ATF temperature.This is caused by a damaged bearing in the transaxle due to improper configuration of the transaxle case. A modification has now been implemented on automatic transaxles with the following serial numbers: 7TN0820364 and higher (CX-3) / 8TN1090104 and higher (except CX-3) 8TR1008883 and higher 8TD1003276 and higher 8T50331192 and higher (CX-3) / 8T50329705 and higher (except CX-3).

This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the driveshaft. To correct this issue, the thickness of the dust cover has been increased.

This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and right side for RHD vehicle). NOTE: The noise will not occur if the steering wheel is in the center or to the full passenger-side position.The noise is caused when the edge (A) of the inner ball joint (B) gets stuck with the steering gear housing(C). To eliminate the noise, a spacer (A) has been installed between the inner ball joint (B) and the steering gear housing (C) (both sides) to prevent direct contact.

This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the drive shaft. To correct this issue, the thickness of the dust cover has been increased.

configuration.

This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the driveshaft. To correct this issue, the thickness of the dust cover has been increased.

This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and right side for RHD vehicle). NOTE: The noise will not occur if the steering wheel is in the center or to the full passenger-side position. The noise is caused when the edge (A) of the inner ball joint (B) gets stuck with the steering gear housing (C). To eliminate the noise, a spacer (A) has been installed between the inner ball joint (B) and the steering gear housing (C) (both sides) to prevent direct contact.

Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

when accelerating after deceleration at 25-40 mph (40-65 km/h), Hard to shift into 3rd, 4th, 5th, and/or 6th gear, Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.

This concern may be caused when a load, which is applied to the seat during braking, exceeds a certain level that could impact the retaining mechanism of the seat lifter causing the seat to gradually move downward. To eliminate this concern, the play in the lift mechanism gears has been reduced.

when accelerating after deceleration at 25-40 mph (40-65 km/h) Hard to shift into 3rd, 4th, 5th, and/or 6th gear Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.

This noise only occurs when starting to move the vehicle while the steering wheel is turned to the full left position. NOTE: The noise will not occur if the steering wheel is in the center or full right position. The noise is caused when the edge (A) of the left side inner ball joint (B) gets stuck with the steering gear housing (C).

BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR SHIFT LEVER VIBRATES WHEN DRIVING IN 3RD OR 4TH GEAR THIS IS CAUSED BY INAPPROPRIATE TRANSMISSION INTERNAL PARTS.

BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR SHIFT LEVER VIBRATES WHEN DRIVING IN 3RD OR 4TH GEAR THIS IS CAUSED BY INAPPROPRIATE TRANSMISSION INTERNAL PARTS.

ONLY USE ATF-FZ TO FILL OR TOP OFF THE FLUID LEVEL. ATF-FZ IS SPECIALLY DESIGNED FOR USE IN THE SKYACTIV-DRIVE SERIES AT. IT IS A LOW VISCOSITY FORMULA WITH LESS FRICTION FOR BETTER FUEL ECONOMY. NOTE: ATF-FZ IS COLORED BLUE FOR EASY IDENTIFICATION. TO CHECK THE FLUID LEVEL, REMOVE THE BOLT, THEN REMOVE THE DIPSTICK. THE DIPSTICK IS MARKED WITH A FZ ON SKYACTIV-DRIVE FW6A-EL AT. WHEN FINISHED, INSERT THE DIPSTICK AND INSTALL THE BOLT.

SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owners Manual, Workshop Manual, Technical Service Bulletin, etc.).

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface.

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Some customers may complain of the poor appearance. This concern is caused by gas that emits from a gasket in the lamp unit. The gas adheres to the inner surface of the headlight lens and reacts with the anti-clouding coating and moisture in the air to create white milky stains. The gasket material has been improved to eliminate this concern.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Use the information below to troubleshoot the customers complaint: MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE CANNOT COMMUNICATE WITH VEHICLE ERROR MESSAGE INSTALLED ON ANDROID DEVICES COMMUNICATION ERRORS MMS CHECK MODE - Use to verify system operation (see below).

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

longer has access or service." for the MMS APP installed on android devices starting 8/1/18. Inform the customer that all they need to do is update the MMS APP to the latest version to get rid of the error message.

Radar units are configured to the original vehicle, and if installed in another vehicle, a configuration error will occur. Refer to MGSS (RADAR UNIT INSPECTION) for proper diagnosing.

NOTE: You may see ?Selection not available? on IDS when a selecting ?Programming menu?, 108.07 included a timer extension for Programming menu application that had to be installed before the expiration date of 3/27/18. After the expiration, IDS can?t accept the extension. To correct this, uninstall IDS and re-install IDS 108.00 >IDS 108.07 up-date. Select "Remove Mazda data files and settings" as shown below.

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear incertain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Damage can occur when using some cleaners that contain strong acid, alkaline cleanser or organic solvent. Damage caused by using these cleaners is not covered by Mazda's New Vehicle Limited Warranty term.

SOME CUSTOMERS MAY COMPLAIN OF THE POOR APPEARANCE. THIS CONCERN IS CAUSED BY GAS THAT EMITS FROM A GASKET IN THE LAMP UNIT. THE GAS ADHERES TO THE INNER SURFACE OF THE HEADLIGHT LENS AND REACTS WITH THE ANTI-CLOUDING COATING AND MOISTURE IN THE AIR TO CREATE WHITE MILKY STAINS. THE GASKET MATERIAL HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN.

THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMP-TOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM.

SOME CUSTOMERS MAY COMPLAIN OF THE POOR APPEARANCE. THIS CONCERN IS CAUSED BY GAS THAT EMITS FROM A GASKET IN THE LAMP UNIT. THE GAS ADHERES TO THE INNER SURFACE OF THE HEADLIGHT LENS AND REACTS WITH THE ANTI-CLOUDING COATING AND MOISTURE IN THE AIR TO CREATE WHITE MILKY STAINS. THE GASKET MATERIAL HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN.

ALTHOUGH THE OVERALL FUNCTION IS THE SAME AS PREVIOUS VEHICLES, VEHICLE DETECTION IS DIFFERENT. FOR DETAILED BSM SYSTEM INFORMATION, REFER TO SERVICE HIGHLIGHTS.

SOME VEHICLES EQUIPPED WITH LED OR DISCHARGE TYPE HEADLIGHTS MAY EXHIBIT WHITE MILKY STAINS ON THE INNER SURFACE OF HEADLIGHT LENS. SOME CUSTOMERS MAY COMPLAIN OF POOR APPEARANCE. THIS CONCERN IS CAUSED BY GAS THAT EMITS FROM A GASKET IN THE LAMP UNIT. THE GAS ADHERES TO INNER SURFACEOF HEADLIGHT LENS AND REACTS WITH ANTI-CLOUDING COATING AND MOISTURE IN THE AIR TO CREATE WHITE MILKY STAINS. THE GASKET MATERIAL HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN. CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED USING THE FOLLOWING REPAIR PROCEDURE.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

road.

25-30 MPH. The bibration may be caused by wear on the inner surface of the tripod joint case (inner side of front drive shaft). To eliminate this concern, a coating has been applied to the inner surface of the tripod joint case to improve wear resistance

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

Customers having this concern should have their vehicle repaired using the following repair procedure.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?

under moderate acceleration, at speeds of approx. 25 - 30 mph (40 - 50 km/h). The vibration is more noticeable when driving on smooth, flat roads.The vibration may be caused by wear on the inner surface of the tripod joint case (inner side of front driveshaft). To eliminate this concern, a coating has been applied to the inner surface of the tripod joint case to improve wear resistance.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

be caused by an insufficient wear resistance of the steering wheel surface.

FOLLOW STEERING WHEEL ALIGNMENT PROCEDURE.

UNDER MODERATE ACCELERATION, AT SPEEDS OF APPROX. 25 - 30 MPH (40 - 50 KM/H). THE VIBRATION IS MORE NOTICEABLE WHEN DRIVING ON SMOOTH, FLAT ROADS. THE VIBRATION MAY BE CAUSED BY WEAR ON THE INNER SURFACE OF THE TRIPOD JOINT CASE (INNER SIDE OF FRONT DRIVE SHAFT).TO ELIMINATE THIS CONCERN, A COATING HAS BEEN APPLIED TO THE INNER SURFACE OF THE TRIPOD JOINT CASE TO IMPROVE WEAR RESISTANCE.

be wet.

be wet.

be wet.

This includes the use of intermediate positions.

If another CX-5 is not available, check the heater core flow and if restricted, drain/replace coolant and replace the heater core. NOTE: If the code is set by itself, without overheating and/or no heat from the heater, follow the Workshop Manual on MS3 online.

Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.

lights ON due to foggy FSC lens will be reduced. However, the warning message will be displayed on the Multi-Information Display (MID) or the center display when FSC lens is foggy. ? The foggy FSC lens may occur at some weather conditions and is not caused by a defect of the parts. When the warning message is displayed, drive the vehicle for 10 minutes or more with the defroster ON to defogthe FSC lens.

UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR).OTE FOR CUSTOMER: THE FSC MAY NOT WORK PROPERLY UNDER THE CONDITIONS:THE WINDSHIELD IS NOT CLEAR. THE FSC LENS IS NOT CLEAR. DRIVING IN HEAVY RAIN, DENSE FOG OR SNOW, OR INTO THE SUN. DRIVING ON A ROAD WITH NO OR BLURRED ROAD LANE MARKINGS. WHEN THE WINDSHIELD BECOMES FOGGY IN THE WINTER TIME OR OTHER COLD WEATHER CONDITIONS AND LDWS/HBC WARN-ING LIGHTS TURN ON, DRIVE WITH THE DEFROSTER ON FOR ABOUT 10 MINUTES. THIS WILL HELP CLEAR THE FOGGY WINDSHIELD AT THE FSC.

IF ANOTHER CX-5 IS NOT AVAILABLE, CHECK THE HEATER CORE FLOW AND IF RESTRICTED, DRAIN/REPLACE COOLANT AND REPLACE THE HEATER CORE. NOTE: IF THE CODE IS SET BY ITSELF, WITHOUT OVERHEATING AND/OR NO HEAT FROM THE HEATER, FOLLOW THE WORKSHOP MANUAL ON MS3 ONLINE.

THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.

THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.

UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR).OTE FOR CUSTOMER: THE FSC MAY NOT WORK PROPERLY UNDER THE CONDITIONS:THE WINDSHIELD IS NOT CLEAR. THE FSC LENS IS NOT CLEAR. DRIVING IN HEAVY RAIN, DENSE FOG OR SNOW, OR INTO THE SUN. DRIVING ON A ROAD WITH NO OR BLURRED ROAD LANE MARKINGS. WHEN THE WINDSHIELD BECOMES FOGGY IN THE WINTER TIME OR OTHER COLD WEATHER CONDITIONS AND LDWS/HBC WARN-ING LIGHTS TURN ON, DRIVE WITH THE DEFROSTER ON FOR ABOUT 10 MINUTES. THIS WILL HELP CLEAR THE FOGGY WINDSHIELD AT THE FSC.

IF ANOTHER CX-5 IS NOT AVAILABLE, CHECK THE HEATER CORE FLOW AND IF RESTRICTED, DRAIN/REPLACE COOLANT AND REPLACE THE HEATER CORE. NOTE: IF THE CODE IS SET BY ITSELF, WITHOUT OVERHEATING AND/OR NO HEAT FROM THE HEATER, FOLLOW THE WORKSHOP MANUAL ON MS3 ONLINE.

The following are possible causes of floor mat interference, which can be avoided with proper usage.

However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts. CAUTION: Be aware that when cleaning the brand emblem, never use cleaning products that are highly acidic/alkaline detergent, organic solvents or those with aggressive chemical products, otherwise, the brand emblem may become cracked and/or deformed (as shown in the example below). Always refer customers to the owners manual for proper cleaning using cold or lukewarm water and a mild, neutral detergent.

The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.

User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. We apologize for any inconvenience this may have caused you or your dealer.

SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.THIS SERVICE BULLETIN IS ONLY FOR SUBLET REPAIR. A QUALIFIED UPHOLSTERY REPAIR SPECIALIST IS REQUIRED FOR THIS REPAIR PROCEDURE. PLEASE PRINT A COPY OF THIS BULLETIN FOR THE UPHOLSTERY REPAIR SPECIALIST.

SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.THIS SERVICE BULLETIN IS ONLY FOR SUBLET REPAIR. A QUALIFIED UPHOLSTERY REPAIR SPECIALIST IS REQUIRED FOR THIS REPAIR PROCEDURE. PLEASE PRINT A COPY OF THIS BULLETIN FOR THE UPHOLSTERY REPAIR SPECIALIST.

CERTAIN PARTS USED ON 2013-2016 MX-5/MIATA CLUB AND LAUNCH EDITIONS WERE ADDED BY MNAO'S PORT FACILITIES OR DEALERS AND ARE NOT SHOWN IN THE BEPC. REFER TO THE ILLUSTRATIONS BELOW TO ORDER SERVICE PARTS.

Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. E85: A blend of 85% ethanol and 15% gasoline All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V.

when the air conditioner (A/C) is ON. This concern may be caused by A/C refrigerant leaking from the evaporator (A) at the joint between the tubes (B) and the header (C) due to improper brazing (D). To correct the problems, the coinfiguration of the header has been changed to improve the brazing performance in this area.

when the air conditioner (A/C) is ON. This concern may be caused by A/C refrigerant leaking from the evaporator (A) at the joint between the tubes (B) and the header (C) due to improper brazing (D). To correct the problem, the configuration of the header has been changed to improve the brazing performance in this area.

Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).

This concern may be caused by A/C refrigerant leaking from the evaporator at the joint between the tubes and the header due to improper brazing. To correct the problem, the configuration of the header has been changed to improve the brazing performance in this area.

Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).

THIS MAY BE CAUSED BY SNOW WITH ROAD SALT BEING BROUGHT INTO THE FOOTWELL AREA. THE MELTED SALT WATER THEN FLOWS ALONG THE OPENER LEVER (A) AND ENTERS INTO THE CABLE (B) CAUSING THE INNER-CABLE TO CORRODE AND SEIZE. TO CORRECT THE PROBLEM, A FLANGE HAS BEEN ADDED TO THE FUEL FILLER LID OPENER LEVER (A) TO PREVENT WATER FROM FLOWING ALONG THE LEVER TO THE FUEL FILLER LID CABLE.

FAHRENHEIT (0 DEGREES CELSIUS).THE ACCELERATOR PEDAL HAS BEEN CHANGED TO INCREASE DURABILITY.

INSTEAD, THE WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING EVAP LEAK TESTER WILL BE USED TO TROUBLESHOOT EVAP SYSTEM LEAKS.

74.00.311 or later).

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.352 or later).

uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.

service loaner program for Special Service Program (SSPA6) for an additional 5 months to improve the low completion rate for campaign SSPA6.

Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version.

The new version number is 59.00.502. Please refer to TSB 09-017/17 for a list of improvements to the system.

Action required: As previously advised the MDRT Tool loaner software expired July 15, 2020. All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by August 21, 2020. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge. New Mazda dealers that do not have this tool, please fill out the Dealer Recall Help form on MXConnect > Warranty to advise you do not have the tool.

the MDRT Tool loaner software expired July 15, 2020. All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by August 21, 2020. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge. New Mazda dealers that do not have this tool, please fill out the Dealer Recall Help form on MXConnect > Warranty to advise you do not have the tool.

the MDRT Tool loaner software expired July 15, 2020. All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by August 21, 2020. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge. New Mazda dealers that do not have this tool, please fill out the Dealer Recall Help form on MXConnect > Warranty to advise you do not have the tool.

downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. When parked, new messages can be displayed or read by the system. When driving, new messages can be read to the vehicle occupants.

downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. When parked, new messages can be displayed or read by the system. When driving, new messages can be read to the vehicle occupants.

Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.

On October 2, 2017, Mazda Technical Services sent out an email extending the Mazda Diagnostic Reprogramming Tool (MDRT) service loaner program for Special Service Program (SSPA6) for an additional 3 months to improve the low completion rate for campaign SSPA6. We are at roughly 84% completion for this campaign. In order to maximize the completion rate as close as we can to 100%, we are extending the MDRT tool loaner program until June 30, 2018 and will evaluate the completion percentage again.

If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.

If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.

If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.

THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. THE NOISE BECOMES MORE NOTICEABLE WHEN DRIVING OVER HIGHER BUMPS. THE CREAKING NOISE IS CAUSED WHEN THE FRONT LOWER CONTROL ARM BUSHING(S) (A) BECOME WET.

THIS MAY BE CAUSED BY FRONT WHEEL HUB BEARING CORROSION.

IF ANY TYPE OF GREASE OR LUBRICATION IS APPLIED TO THE BUSHINGS, IT MAY CREATE NOISE DUE TO BUSHING SLIPPAGE.

IF ANY TYPE OF GREASE OR LUBRICATION IS APPLIED TO THE BUSHINGS, IT MAY CREATE NOISE DUE TO BUSHING SLIPPAGE.

This may be caused by a loose spare tire jack.

This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.

THE VEHICLE CAN SLIP OFF THE JACK AND SERI-OUSLY INJURE SOMEONE. IN THIS SERVICE INFORMATION, SOME IMPORTANT WARNINGS AND CAUTIONS HAVE BEEN TAKEN FROM THE OWNERS MANUAL. FOR MAZDA CUSTOMERS WHO HAVE QUESTIONS ABOUT SAFELY LIFTING THEIR VEHICLE TO CHANGE A FLAT TIRE OR TO INSTALL SNOW CHAINS, PLEASE PROVIDE A COPY OF THE ATTACHED HANDOUT FOR THEM. ALSO, BE SURE TO ALWAYS DIRECT CUSTOMERS TO FOL-LOW THE DIRECTIONS IN THE OWNER'S MANUAL.

THIS MAY BE CAUSED BY A LOOSE SPARE TIRE JACK.