2016 Mazda CX-3 TSBs

interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button

The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.

The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.

The changes are noted in Red text. MT-003/22 03/02/22 DESCRIPTION Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. The concern will likely occur if the fuel tank is overfilled (more fuel is added after the fuel pump nozzle shuts off automatically) or filled up normally in high ambient temperatures and the fuel expands. No repair is needed. Explain to the customer not to continue filling after nozzle shut off.

The changes are noted in Red. 01-008/23 06/05/23 Some vehicles may exhibit rattling noises from the engine compartment and oil leakage from the drive belt auto tensioner. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed. REPAIR PROCEDURE If the tensioner is found to be "No Good" after completing the Drive Belt Auto Tensioner Inspection, replace it with a modified part according to the instructions on MGSS online:

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). Only Mazda-approved key cutting machines can process these 10-digit codes. Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service. Examples of residue or seepage that may not be considered a leak and that may not require repair based on splash shield inspection.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

Foreign debris on the blower motor after servicing the cabin air filter may be the cause. During the removal of the cabin air filter, foreign debris (leaves, dust, dirt....ect.) may fall on the blower motor causing a fluttering type noise or odor.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

As a result of a Mazda Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

Connect Infotainment Class Action settlement, Mazda Motor Corporation has decided to implement a Customer Service Program (CSP13). The coverage and terms for vehicles are listed below in this Dealer email and in attached documentation. Only certain vehicles, 2014-2018 Mazda3, 2016-2021 Mazda6, 2016-2021 CX-3, 2016-2020 CX-5, 2016-2020 CX-9, 2016-2023 MX-5, 2016-2022 Mazda2(Puerto Rico Market vehicles) AND that have CSP13 listed in Warranty Vehicle Inquiry are covered under this CSP. Please review the attached document titled Subject Vehicles CSP13 for details on the covered vehicle models, model year and production VIN ranges.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

may complain of leakage at or around the washer motor (1). This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section. This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section.

This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).

DTC B00A0:09 (Occupant classification sensor internal signal output unstable). This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily. The concern occurs more often in colder weather when greater electric current is consumed to start the vehicle. To eliminate this concern, the OCS has been modified to avoid unnecessary DTC detection. NOTE: Even if the voltage is recovered after the engine is started, the airbag warning light stays ON during the drive cycle. When the battery voltage becomes stable after the engine is started, the airbag system will operate normally.

These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.

Vehicles having this concern should use the following Inspection/Repair procedure.

customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay/ Android Auto will not connect) 6. Over-sized wheels/tires (incorrect GPS location)

control valve is closed and air in the engine cannot escape during ignition ON. Therefore, turn the ignition OFF when refilling engine coolant using the radiator filler neck.

fast idle to normal idle speed during cold start. This is caused by a variable valve being stuck in the closed position. When returning from fast idle to normal, the stuck valve suddenly opens due to thermal change around it which causes abnormal noise. To eliminate this concern, the internal design of the exhaust manifold has been modified.

Stored in TCM Memory

*DTC B00A0:09 (Occupant classification sensor internal signal output unstable) This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily. The concern occurs more often in colder weather when greater electric current is consumed to start the vehicle. To eliminate this concern, the OCS has been modified to avoid unnecessary DTC detection. NOTE: *Even if the voltage is recovered after the engine is started, the airbag warning light stays ON during the drive cycle. *When the battery voltage becomes stable after the engine is started, the airbag system will operate normally.

The concern will likely occur if the fuel tank is overfilled (more fuel is added after the fuel pump nozzle shuts off automatically) or filled up normally in high ambient temperatures and the fuel expands. No repair is needed. Explain to the customer not to continue filling after nozzle shut off. Refer customer to Owner's Manual Warning:

malfunction) stored, the cylinder deactivation oil control valve may be plugged with plastic debris from the oil filter wrapper. The debris may enter the center of the oil filter when poking a hole in the filter wrapper during removal, and then travel through the engine and plug the cylinder deactivation oil control valve.

Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline, E85: A blend of 85% ethanol and 15% gasoline, All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V. What if a customer puts E85 in there Mazda vehicle? Symptoms include: Rough Running, Lean Codes, Misfires and/or misfire codes, Lack of power, Poor fuel economy, Spark knock, Mechanical engine damage.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on, P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on, P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on, P0780:00 - Gear shifting malfunction, P1738:00 Automatic transaxle internal malfunction. This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.

may complain of leakage at around the washer motor (1).This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section.

This may be caused by a customer installed aftermarket decorative trim and/or cover on the START/STOP ENGINE button. The aftermarket accessory may create electrical interference, which may interfere with programming.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

P2610:00: Instrument cluster internal engine off timer performance problem. P2507:00: PCM battery voltage low input

when turning the steering wheel while the vehicle is stopped.

and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery voltage low input.

As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? Yes - No repair is necessary. No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE).

The concern will likely occur if the fuel tank is overfilled (more fuel is added after the fuel pump nozzle shuts off automatically) or filled up normally in high ambient temperatures and the fuel expands.

head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic.

DTC B00A0:09 (Occupant classification sensor internal signal output unstable). This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily. The concern occurs more often in colder weather when greater electric current is consumed to start the vehicle. To eliminate this concern, the OCS has been modified to avoid unnecessary DTC detection. NOTE: Even if the voltage is recovered after the engine is started, the airbag warning light stays ON during the drive cycle. When the battery voltage becomes stable after the engine is started, the airbag system will operate normally.

DTC B00A0:09 (Occupant classification sensor internal signal output unstable). This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily. The concern occurs more often in colder weather when greater electric current is consumed to start the vehicle. To eliminate this concern, the OCS has been modified to avoid unnecessary DTC detection. NOTE: Even if the voltage is recovered after the engine is started, the airbag warning light stays ON during the drive cycle. When the battery voltage becomes stable after the engine is started, the airbag system will operate normally.

P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display F0-002 during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km).Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear Parking Sensors - Rear Seat Entertainment - Smartphone Screen Mirroring - Bumper Trim/Guards - Door Mirror Caps - Fog Lights - Moonroof Wind Deflector - Roof Rack - Side Window Deflectors - Splash Guards - Trailer Hitch - Thule Products - Wheels Locks - Aero Kit - Air Dam - Rear Spoiler - Tunnel Under Bars - Lower Arm Bar - Side Sill Extensions - Arm Rest - Illuminated Door sill Trim Plates - Interior Lighting

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.

Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.

This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.

Engine Start/Start Button Amber indicator light flashing Battery discharge Electrical relay buzzing noise DTC B13D3:94 (Communication error with remote transmitter) stored.This may be caused by: A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehicless wiring harness may create unusual electrical symptoms.

This may be caused by a plugged heater core. For 2014-2016 Mazda6 and 2013-2016 (US spec) / 2017 (Mexico spec) CX-5, the CHECK ENGINE light may turn on with DTC P011A:00 (ECT sensor No.1/No.2 performance problem) stored at the same time. NOTE: Refer to TSB 01-015/15 if the customer is using a block heater at temperatures below freezing. To solve this concern, two mass production changes have been implemented. a) The concentration of the coolant has been increased so that the amount of the contained anti-rust additive is higher. b) The composition of the coolant has been changed (the ratio of the anti-rust additive has increased).

Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:

before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

surface.This is caused by the slide pin (1) hitting the mounting support (2) due to insufficient holding power of the dust boots (3) when a shock (4) is applied from the road. To eliminate this concern, the dust boots have been modified to increase holding power.

P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.

The aluminum tape may have dropped from the bottom of the steering column and the black liquid is grease that has melted and dripped onto the floor. This concern is caused by the grease from the power steering motor seeping out and loosening the adhesive on the aluminum tape. Parking in the sun can create high interior temperatures which may melt the grease and loosen the adhesive. To eliminate this concern, a housing cover has been added to the affected area of the steering column.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 - Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.

The concern will likely occur if the fuel tank is overfilled (more fuel is added after the fuel pump nozzle shuts off automatically) or filled up normally in high ambient temperatures and the fuel expands.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial checkis a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.

Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory. P0300 - Random misfire detected P0301 - Cylinder No. 1 misfire detected P0302 - Cylinder No. 2 misfire detected P0303 - Cylinder No. 3 misfire detected P0304 - Cylinder No.4 misfire detected. This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow.

Unlike previous Mazda models, there is no key cylinder on the steering column. Therefore, the engine cannot be started with the auxiliary key if the room fuse is removed or if the transmitter battery is dead.

P0456: EVAP system leak detected (very small leak). The concern is most likely the result of the customer not getting the fuel cap completely closed after fueling the vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.

The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. This can happen if the ignition is turned OFF within 20 seconds after the ignition is turned ON in one of the following two situations. 1. The ?ROOM? fuse (Engine compartment) is NOT installed when battery level is low. 2. The CMU (Connectivity Master Unit) is NOT connected.

refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.

deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. This can happen if the ignition is turned OFF within 20 seconds after the ignition is turned ON in one of the following two situations. 1. The ?ROOM? fuse (Engine compartment) is NOT installed when battery level is low. 2. The CMU (Connectivity Master Unit) is NOT connected.

refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system. When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur to oxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise.This may be caused by: A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehicles?s wiring harness may create unusual electrical symptoms.

A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger, GPS tracker...) may create excessive electrical noise. The noise may interrupt some of the vehicle electrical systems. Below are a few examples of an aftermarket cell phone charger and GPS tracker that are interrupting the vehicle electrical systems.

customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing.

complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger) may create excessive electrical noise. The noise may interrupt some of the vehicle electrical systems. Below are a few examples of an aftermarket cell phone charger that is interrupting the vehicle electrical systems.

(e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

temperature), the engine oil may become diluted with fuel and the engine oil level will increase. Engine oil dilution with fuel occurring under this specific driving condition is normal with direct injection engines. If the vehicle is driven on a longer trip after a lot of short trips (where the engine reaches normal operating temperature), the Check Engine Light may turn ON with DTC P0172:00 (Fuel system too rich).

P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely closed after fuelingthe vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.

P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to MGSS online for proper diagnosis and repair procedure.

This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial check is a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.

Unlike previous Mazdamodels, there is no key cylinder on the steering column. Therefore, the engine cannot be started with theauxiliary key if the room fuse is removed or if the transmitter battery is dead.NOTE: The auxiliary key can only be used to lock or unlock the doors. It cannot be used to start the engine. Two transmitters are placed in a vinyl bag and stored in the center console cup holder. Since the room fuse is not installed during vehicle assembly, a new procedure is required to start the engine. Refer to "Engine Start Procedure" below.

P0015:00 - Exhaust CMP timing over-retarded P0524:00 - Engine oil pressure too low This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.

The unique oil filter can be identified with two white bands as shown below.

Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory. P0300 - Random misfire detected P0301 - Cylinder No.1 misfire detected P0302 - Cylinder No.2 misfire detected P0303 - Cylinder No.3 misfire detected P0304 - Cylinder No.4 misfire detected. This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow.

when turning the steering wheel while the vehicle is stopped.The noise may be due to: Upper front strut bearing (A) damage. (CX-5 and Mazda6) Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6) The bump stopper (C) may be contacting the strut bearing when the front shock absorber is compressed, causing a popping noise. (Mazda6 only) The front lower arm bushing (D) is making a creak type noise in wet road conditions. (CX-5 and Mazda6).Front Shock Absorber Front Lower Arm To eliminate the noise, the following mass-production changes have been made: 1. The material and production method of the front strut bearing (A) has been changed. (CX-5 and Mazda6) 2. A protector has been installed onto the coil spring. (CX-5 and Mazda6) 3. The shape of the bump stopper (C) will be modified in the future. (Mazda6 only) 4. The shape of the coil spring has been changed. (CX-3 only) 5. Friction of the lower arm bushing has been reduced by adding a dry coating. (CX-5 and Mazda6). NOTE: The piston rod nut (B) requires replacement.

Vehicles having this concern should use the following Inspection/Repair procedure.

P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.

NOTE: Engine misfire related DTCs (P0301, P0302, P0303, P0304) are usually stored at the same time. P0201:00 : Fuel injector circuit/open cylinder No.1 P0202:00 : Fuel injector circuit/open cylinder No.2 P0203:00 : Fuel injector circuit/open cylinder No.3 P0204:00 : Fuel injector circuit/open cylinder No.4 This concern may be caused by an internal failure of the PCM (DENSO produced only). To correct the concern, the PCM internal failure has been eliminated.

when turning the steering wheel while the vehicle is stopped.The noise may be due to:? Upper front strut bearing (A) damage. (CX-5 and Mazda6)? Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6)? The bump stopper (C) may be contacting the strut bearing when the front shock absorber is compressed, causing a popping noise. (Mazda6 only)? The front lower arm bushing (D) is making a creak type noise in wet road conditions. (CX-5 and Mazda6).

when turning the steering wheel while the vehicle is stopped. The noise may be due to: Upper front strut bearing (A) damage. (CX-5 and Mazda6). Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6). The bump stopper (C) may be contacting the strut bearing when the front shock absorber is compressed, causing a popping noise. (Mazda6 only). The front lower arm bushing (D) is making a creak type noise in wet road conditions. (CX-5 and Mazda6).

NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the ?SpeedometerReplacement Label?.Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda?s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.With the use of SPECMO?s services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

the display is adjusted through the Settings screen. This is caused by an incorrectly learned zero-point (closed position) of the Active Driving Display. The main reason this happens is because an object (e.g. gloves, paper, etc. ) was placed in the storage area where the mirror and optical receiver are housed. If an object is detected (i.e., jammed) when the Active Driving Display closes after switching the ignition OFF, the system determines this as abnormal and stops the closing operation, leaving the Active Driving Display in an open position. When the engine is started the next time, correction of the zero-point is automatically performed. If the object is still in the storage area during the correction, the system learns the incorrect position as the zero-point. As a result, the zero-point position largely deviates from the standard position; therefore, it becomes impossible to view the Active Driving Display from the normal view position.

when turning the steering wheel while the vehicle is stopped. The noise may be due to: *upper front strut bearing (A) damage. (CX-5 and Mazda6) *squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6) *the bump stopper (C) may be contacting the strut bearing when the front shock absorber is compressed, causing a popping noise. (Mazda6 only) *The front lower arm bushing (D) is making a creak type noise in wet road conditions. (CX-5, Mazda6 and CX-9).

Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory.?P0300 - Random misfire detected ?P0301 - Cylinder No.1 misfire detected ?P0302 - Cylinder No.2 misfire detected ?P0303 - Cylinder No.3 misfire detected ?P0304 - Cylinder No.4 misfire detected This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow.

LANE DEPARTURE WARNING SYSTEM (LDWS) WARNING LIGHT TURNS ON AT IDLE. DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY.2.ADAPTIVE LED HEADLIGHTS (ALH) WARNING LIGHT TURNS ON WHILE DRIVING. DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY.UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR).

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO: UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6) STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY) TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE: 1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6) 2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6) 3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY) 4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY) NOTE: THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES.

WARNING SYSTEM (LDWS) WARNING LIGHT TURNS ON AT IDLE. DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY.2. ADAPTIVE LED HEADLIGHTS (ALH) WARNING LIGHT TURNS ON WHILE DRIVING. DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY.UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR).

P2610:00: INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM P2507:00: PCM BATTERY VOLTAGE LOW INPUT AS A PAST MALFUNCTION, THE CUSTOMER WILL NOT NOTICE IT (NO WARNING LIGHT ILLUMINATED), BUT THE DTC MAY BE FOUND DURING A VEHICLE SERVICE. P2507 IN THIS SITUATION IS ONLY APPLICABLE ON 2016 AND LATER MODELS. THIS IS CAUSED BY THE ENGINE BEING STARTED 3 OR MORE TIMES AFTER A SHORT DURATION OF ENGINE OFF (LESS THAN 15 SECONDS) WITH THE ROOM FUSED REMOVED.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6)TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

THE PURPOSE OF A PERMANENT DTC IS TO PREVENT CUSTOMERS FROM CLEARING THEM BY DISCONNECTING THE BATTERY CABLE IN ORDER TO PASS A SMOG CHECK. ALL PCM AND TCM DTCS THAT TURN ON THE CHECK ENGINE LIGHT CAN REMAIN AS A PERMANENT DTC. THEY WILL NOT TURN ON THE CHECK ENGINE LIGHT OR CAUSE DRIVABILITY CONCERNS. IF YOU ENCOUNTER A PERMANENT DTC, IGNORE IT AND DIAGNOSE THE CURRENT STORED OR PENDING DTC.

THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES. ALL SKYACTIV ENGINES EQUIPPED WITH OIL PRESSURE SWITCH PART NUMBER PE01-18-501A ARE APPLICABLE TO THIS ISSUE.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6).TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT.

THE UNIQUE OIL FILTER CAN BE IDENTIFIED WITH TWO WHITE BANDS AS SHOWN BELOW.

- EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6). TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738).P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONP0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.NOTE:IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6)TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6). TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738).P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONP0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.NOTE:IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.

BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT

WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6).TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.

SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING 2 SYMPTOMS, EVEN THOUGH THE WINDSHIELD IS CLEAR. LANE DEPARTURE WARNING SYSTEM (LDWS) WARNING LIGHT TURNS ON AT IDLE; DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY. ADAPTIVE LED HEADLIGHTS (ALH) WARNING LIGHT TURNS ON WHILE DRIVING; DTC C1001:92 (POOR FUNCTIONING OF FORWARD SENSING CAMERA (FSC)) IS STORED IN MEMORY.

Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with an active SAT radio.

The film of the center display may be peeled off. White dots may appear on the center display. Spider web-like cracking appearing in the corner(s) of the MAZDA CONNECT center display (the cracks are internal and cannot be felt by touch).

Peeling, spider cracks and white dots.

The film of the center display may be peeled off. White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts.

IT IS SUPERCEDED BY RECALL 6023G (2014-2018 MAZDA3 AND 2016-2021 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY).

superseded by "RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY". Use the link below to view the recall: RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY

- The film of the center display may be peeled off. - White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.

- The film of the center display may be peeled off. - White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.

screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.

screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.

It includes new display repair kit part numbers for the 2018-2019 Mazda2, 2018-2020 CX-3 and 2018-2020 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White dots

There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Please use the table below when ordering the screen repair kits. This can also be found in Service Alert SA-041/22.

Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] * B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] * No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. * In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). * In other cases this DTC might be found without a related customer concern. NOTE: In most cases, no dealer visit is necessary.

- The film of the center display may be peeled off. - White dots may appear on the center display

Spider Cracks - Surface Peeling - White dots

Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.

The cracks are internal and cannot be felt by touch. This concern may be caused by a lack of glue between the touch screen and the center display. To eliminate this concern in the future, the manufacturing process has been improved.

possible due to continuous reboot.

Mazda is aware of the issue and is working on a resolution. This Service Alert will be updated with the newest repair information as it becomes available.

No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. 6 Bluetooth device will not pair No. 7 Incorrect GPS position No. 8 Voice Recognition Does Not Work No. 9 Cannot Make a Hands-Free Call No. 10 Cannot Play Bluetooth Audio No. 11 Other Symptoms No. 12 How to update the Navigation SD Card Map No. 13 How to Check Navi SD Card VIN Lock

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.230 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software. Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

This may be caused by an incorrect clock GPS Sync setting.

All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.

All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction.

/ Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions

When the concern occurs, MAZDA CONNECT reboots repeatedly, and if the SD card is removed during this reboot cycle, the rebooting cycle ends. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error. To correct the concern, the SD card hardware has been changed.

Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles], B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles build on or before March 2, 2019], No DTC - Gen 7 vehicles built after March 2, 2019, DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

/ Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions

After the installation of a new instrument cluster, the message "Fctry" is displayed instead of the odometer. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.

Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature.

All Mazda connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin.

After the installatioin of a new instrument cluster, the message "F ctry" IS DISPLAYED INSTEAD OF THE ODOMETER. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.

This may be caused by an aftermarket accessory device.

Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. If swapped, the SD card that is installed into the other vehicle becomes linked to the VIN of that vehicle.

Navigation voice guidance will skip and cut out losing many words.Pandora will suddenly disconnect and MAZDA CONNECT will revert to the previously used source. If you encounter a vehicle with these issues, DO NOT attempt any repairs on the vehicle. There is nothing wrong with the vehicle. This is an issue with the Pandora APP. Have the customer contact Pandora at pandora-support@pandora.com. NOTE: If the Pandora APP works on the customer's phone, they can stream Pandora using Bluetooth.

Replace the Active Driving Display.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.

CarPlay / Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS - Infotainment - MAZDA CONNECT Updates - Apple Carplay / Android Auto MDARS Activation Instructions

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update.

The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the SD card hardware has been changed.

The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the SD card hardware has been changed.

This may be caused by an incorrect clock GPS Sync setting.

of view B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.

Audio System, Bluetooth, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux Voice Command, How to Check Navi SD Card VIN Lock.

Use the troubleshooting chart below to repair the vehicle.

Use the troubleshooting chart below to repair the vehicle.

This may be caused by an incorrect clock GPS Sync setting.

B14F0:92 - General temporary failure in forward sensing camera (FSC). DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details. If the vehicle has this DTC, DO NOT replace the FSC. Read below.

NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazdas continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software.Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

Use the flowchart below to repair the vehicle.

Many frequently asked question and the answers.

Use the flowchart below to repair the vehicle.

aha/Pandora/Stitcher/Bluetooth and the same device is also connected to the USB port for charging. The concerns may include: Blank Screen and/or No Audio Sound, Phone will not charge.Blank Screen and/or No Audio Sound These concerns may be caused by:The MAZDA CONNECT system has reached its capacity limits when streaming music with audio source aha/Pandora/Stitcher/Bluetooth and also connected to the USB port.The MAZDA CONNECT system has reached its capacity limits when the customer's USB device capacity exceeds 16 GB (e.g. 64 GB iPhone X). The MAZDA CONNECT system USB port capacity is 16 GB (FAT32).Mazda recommends not to connect any devices to the USB port when streaming music with audio source aha/Pandora/Stitcher/Bluetooth. When streaming music with audio source aha/Pandora/Stitcher/Bluetooth (without USB connection), the Connectivity Master Unit (CMU) is able to process Bluetooth digital data (A) and output audio sound and display Bluetooth audio information. If the same device is connected to the USB port for charging, the CMU processes both Bluetooth digital data (A) and USB digital data (B) from the same device at the same time. In this case, CMU resources may be exceeded, causing a Blank Screen and/or No Audio Sound.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement. NOTE: Always check for a TSB that may modify or eliminate prior authorization for a specific symptom for a given component.

for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active working SAT radio.

This is caused by a navigation map supplier software change. Customers can set preferences if needed. Example: A customer may have a Shell Gas Card and is only interested in Shell Gas Stations. The customer can set preference to only show Shell gas stations.

Use the flowchart below to repair the vehicle.

This is a normal condition. Album art and artist biographies are not provided by SiriusXM Satellite Radio, a blank white square frame is shown in place of the album art. Note: This information is also available at www.mazdahandsfree.com>FAQ>ENTERTAINMENT - SIRIUSXM. STATION LOGO SIRIUSXM satellite radio hardware is in the Tuner and Amp Unit (TAU). The station logo is not shown in the center display because there is no visual data communication cable between the TAU and the Connectivity Master Unit (CMU). A blank white square frame is shown in place of the station logo. Do NOT perform any repairs for these concerns.

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin.Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.100A or later). NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.

Use the flowchart below to repair the vehicle.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda's continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDACONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software. Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.

DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.

Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement. NOTE: Always check for a TSB that may modify or eliminate prior authorization for a specific symptom for a given component.

for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active (working SAT radio).

To improve the handling of BLUETOOTH hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.

This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.

The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during extremely cold temperatures. To correct the concern, the SD card hardware has been changed.

To resolve this concern, after the installation of the new CMU, check the software version.

aha/Pandora/Stitcher/Bluetooth and the same device is also connected to the USB port for charging. The concerns may include: Blank Screen and/or No Audio Sound, Phone will not charge, Blank Screen and/or No Audio Sound

The cracks are internal and cannot be felt by touch. This may be caused by a faulty center display.

This is a normal condition.

The cracks are internal and cannot be felt by touch. This concern may be caused by a lack of glue between the touch screen and the center display. To eliminate this concern in the future, the manufacturing process has been improved.

This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.

NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda's continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.

This may be caused by faulty navigation SD card software. TheSD card has been updated to eliminate this concern.

The concern occurs when the interior of the vehicle is cold and disappears when the interiorwarms up. This is caused by some for the MAZDA CONNECT navigation system SD cards beingmanufactured with improper hardware, resulting in a data reading error during cold temperatures. To correctthe concern, the SD card hardware has been changed.

This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping.The navigation SD card has a malfunction.

Replace the Active Driving Display.

part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.

59.00.502or later).NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tabin MAZDA CONNECT Settingsbefore performing the update.

DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.

MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux, Voice Command

NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update.

part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502or later). NOTE: For CX-9 with version earlier than 59.00.441, the tachometer function has been removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software.

MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. This concern may be a normal operation of the CMU connecting to available devices on start up.

SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT.

TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750). EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750. NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT. SYSTEM DOES NOT RECOGNIZE USB/SD CARD. SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT. WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT. FAVORITES DISAPPEAR. VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH. REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN. TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE. WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCATION IS COMMA. CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE. NOTE: MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE,AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VERSION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

REPLACE THE ACTIVE DRIVING DISPLAY.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

DIFFERENT SONG WILL PLAY.IF THE CUSTOMER SELECTS A DIFFERENT SONG, MOST OF THE TIME IT WILL CONTINUE PLAYING THE CURRENT SONG.IF THE CUSTOMER SHOULD SELECT THE CURRENT SONG AGAIN, IT MAY START PLAYING A DIFFERENT SONG.

TO IMPROVE THE HANDLING OF BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.CUSTOMERS EXPERIENCING RELATED CONCERNS SHOULD HAVE THEIR VEHICLE AND/OR DEVICE INSPECTED ACCORDING TO THE FOLLOWING PROCEDURE.

PART OF THE NEW CAR READY STEP 3 PROCESS. MAKE SURE THE NEW VEHICLE SPECIALIST RECEIVES A COPY OF THIS BULLETIN.SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 55.00.760 OR LATER).SOME STREET NAMES IN CANADA ARE NOT DISPLAYED.NAVIGATION DOES NOT ALLOW TO SET CERTAIN CITIES AS DESTINATION.NAVIGATION DOES NOT ANNOUNCE VOICE GUIDANCE FOR STREET NAMES.NAVIGATION TURNS TO A BLACK SCREEN REMAINING THE TASK BAR.TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750).EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750.NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT.SYSTEM DOES NOT RECOGNIZE USB/SD CARD.SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT.WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT.FAVORITES DISAPPEAR.VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH.REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN.TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE.WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCA-TION IS COMMA.CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE.NOTE:MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VER-SION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

56.00.760 OR LATER).SOME STREET NAMES IN CANADA ARE NOT DISPLAYED.NAVIGATION DOES NOT ALLOW TO SET CERTAIN CITIES AS DESTINATION.NAVIGATION DOES NOT ANNOUNCE VOICE GUIDANCE FOR STREET NAMES.NAVIGATION TURNS TO A BLACK SCREEN REMAINING THE TASK BAR.TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750).EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750.NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT.SYSTEM DOES NOT RECOGNIZE USB/SD CARD.SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT.WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT.FAVORITES DISAPPEAR.VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH.REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN.TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE.WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCA-TION IS COMMA.CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE.NOTE:MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VER-SION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

CONNECT.NAVIGATION VOICE GUIDANCE WILL SKIP AND CUT OUT LOSING MANY WORDS.PANDORA WILL SUDDENLY DISCONNECT AND MAZDA CONNECT WILL REVERT TO THE PREVIOUSLY USED SOURCE. IF YOU ENCOUNTER A VEHICLE WITH THESE ISSUES, DO NOT ATTEMPT ANY REPAIRS ON THE VEHICLE. THERE IS NOTHING WRONG WITH THE VEHICLE. THIS IS AN ISSUE WITH THE PANDORA APP. HAVE THE CUSTOMER CONTACT PANDORA AT PANDORA-SUPPORT@PANDORA.COM. NOTE: IF THE PANDORA APP WORKS ON THE CUSTOMER'S PHONE, THEY CAN STREAM PANDORA USING BLUETOOTH.

THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE

THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

REPLACE THE ACTIVE DRIVING DISPLAY.

PHONE CALLS WHEN THE SMARTPHONE IS PAIRED WITH A VEHICLE OR WIRELESS HEADSET. THE ISSUE EXTENDS TO GPS VOICE NAVIGATION FOR SOME, BUT STREAMING MUSIC OVER BLUETOOTH APPEARS TO BE UNAFFECTED. SPECIFICALLY, DOZENS OF USERS IN THE APPLE SUPPORT COMMUNITIES AND MACRUMORS DISCUSSION FORUMS CLAIM TO BE EXPERIENCING DISTORTED, STATICKY, OR INAUDIBLE PHONE CALLS WHEN USING AN IPHONE SE. IF YOU EXPERIENCE A CUSTOMER COMPLAINT, AND THE CUSTOMER HAS A NEW IPHONE SE, DO NOT REPLACE ANY PARTS ON THE VEHICLE. EXPLAIN TO THE CUSTOMER THAT THE IPHONE MAY BE THE PROBLEM. HAVE THE CUSTOMER VISIT THIS WEBSITE: HTTP://WWW.MACRUMORS.COM/2016/04/11/IPHONE-SE-BLUETOOTH-PHONE-CALL-AUDIO-ISSUES/

USE THIS VERSION FOR ALL MAZDA CONNECT UPDATES, INCLUDING OPEN SSP98 VEHICLES. IF SSP98 IS CLOSED, USE TSB 09-024/16 TO REPAIR THE VEHICLES.CLICK ON "IDS/INFOTAINMENT", THEN "MAZDA CONNECT UPDATES" TO DOWNLOAD IT. UPDATE YOUR USB DRIVES ACCORDING TO THE INSTRUCTIONS IN TSB 09-024/16.ALSO MAKE SURE TO SELECT "ALL FILES" FOR "SAVE AS TYPE:". IF LEFT AS "COMPRESSED (ZIPPED) FOLDER," THE FILE WILL BE SAVED AS A ".ZIP" NO MATTER WHAT YOU USE AS AN EXTENSION.ATTN: TECHNICIANS - BE SURE TO DOCUMENT THE SOFTWARE VERSION INSTALLED ON THE REPAIR ORDER AND INFORM YOUR WARRANTY ADMINISTRATOR TO PROVIDE THE INFORMATION IN THE REPAIR TEXT OF THE WARRANTY CLAIM.MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VERSION UPDATES CAN BE FOUND ON MS3.

55.00.760 OR LATER).SOME STREET NAMES IN CANADA ARE NOT DISPLAYED.NAVIGATION DOES NOT ALLOW TO SET CERTAIN CITIES AS DESTINATION.NAVIGATION DOES NOT ANNOUNCE VOICE GUIDANCE FOR STREET NAMES.NAVIGATION TURNS TO A BLACK SCREEN REMAINING THE TASK BAR.TURN -BY-TURN NAVIGATION GUIDANCE DOES NOT DISPLAY ON ON THE ACTIVE DRIVING DISPLAY (FOR VEHICLES WITH 55.00.750).EVERY TIME THE NAVIGATION IS TURNED ON, THE VEHICLE POSITION STARTS FROM THE LOCATION (DEALER) WHERE THE CMU WAS UPDATED FROM VERSION 55.00.650 TO 55.00.750.NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT.SYSTEM DOES NOT RECOGNIZE USB/SD CARD. SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT.WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT.FAVORITES DISAPPEAR.VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH.REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN.TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE.WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND WHERE AM I?, THE SYSTEM RESPONDS WITH YOUR LOCA-TION IS COMMA.CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE.NOTE:MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VER-SION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

CONNECT.NAVIGATION VOICE GUIDANCE WILL SKIP AND CUT OUT LOSING MANY WORDS.PANDORA WILL SUDDENLY DISCONNECT AND MAZDA CONNECT WILL REVERT TO THE PREVIOUSLY USED SOURCE. IF YOU ENCOUNTER A VEHICLE WITH THESE ISSUES, DO NOT ATTEMPT ANY REPAIRS ON THE VEHICLE. THERE IS NOTHING WRONG WITH THE VEHICLE. THIS IS AN ISSUE WITH THE PANDORA APP. HAVE THE CUSTOMER CONTACT PANDORA AT PANDORA-SUPPORT@PANDORA.COM. NOTE: IF THE PANDORA APP WORKS ON THE CUSTOMER'S PHONE, THEY CAN STREAM PANDORA USING BLUETOOTH.

ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES LINKED TO THE VIN OF THAT VEHICLE.

SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE: DO NOT paint ground point (3) attachment bolt (4) is seated. NEWLY INSTALLED FRONT FENDER STAY NOTE: CAUTION: If the bolt (4) contact area (3) is painted when the front fender stay (2) is newly replaced, it could cause a malfunction in the PCM. Before painting a newly replaced part, protect the bolt (4) contact area (3) with masking tape (5) as shown in the figure.

the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. In most cases, if the left-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" can be completed without any problem (See CAUTION below for more details). Other possible symptoms that may be found if the right-side BSM module is replaced alone: BSM aiming fails BSM OFF" indicator ON Center Display warning message BSM failsafe (No operation) DTC U3000:54 stored in memory DTC U1A4B:54 stored in memory (CX-3, MX-5 only) NOTE: Since a new BSM control module does not retain the vehicle specification information, it is necessary to acquire and store the vehicle specification information transmitted via CAN communication from the combination meter through automatic configuration after replacement.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.

lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.

lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.

Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.

lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced since December 2021 at the supplier.

This is caused by a failure in the ambient temperature sensor. To correct this issue, the ambient temperature sensor has been modified.

the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. Other possible symptoms that may be found if the right-side BSM module is replaced alone: * BSM aiming fails * "BSM OFF" indicator ON * Center Display warning message * BSM failsafe (No operation) * DTC U3000:54 stored in memory * DTC U1A4B:54 stored in memory (CX-3, MX-5 only)

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

(SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.

maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a good know terminal.To measure the voltage/resistance avoiding any terminal damage.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc.) placed on the front passenger's seat.

data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage.

DTC B00A0:09 (Occupant classification sensor internal signal output unstable). This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily. The concern occurs more often in colder weather when greater electric current is consumed to start the vehicle. To eliminate this concern, the OCS has been modified to avoid unnecessary DTC detection.

Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area. Adjacent vehicle (B) driving at same speed, even if the vehicle is still in the alert area. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address these customer concerns.

The symptoms may include: When the ignition is switched ON, the warning indicator light turns ON momentarily and then turns off after a few seconds. The BSM system does not operate after 1st key cycle (cold soak), No DTCs stored in memory, BSM system will function normally after 2nd key cycle and the vehicle is driven on the street

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . * The display operation does not fully open/close. * It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the act ive driving display which activates pinching detection. Customer having this concern should have their vehicle repaired using the following repair procedure.

on a smooth road surface even if the TPMS system has been properly initialized at the specified tire air pressure. Please contact the Hotline for a countermeasure repair if a vehicle arrives with this issue. A countermeasure control module is due in July for this concern.

This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all auxiliary keys are lost.

Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.

data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. Mazda Air Cooling Coil Coating is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

This concern may also occur when a room fuse is installed in a new vehicle. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required. NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected.

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. Customers concern can be resolved by sanding off paint at ground point (3) where attachment bolt (4) is seated. After installing the bolt (4), apply touch-up paint to the exposed base material area of the front fender stay.

It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.

notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.

the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. Other possible symptoms that may be found if the right-side BSM module is replaced alone: BSM aiming fails, BSM OFF" indicator ON, Center Display warning message, BSM failsafe (No operation), DTC U3000:54 stored in memory, DTC U1A4B:54 stored in memory (CX-3, MX-5 only).

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.

notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.

If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps):CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery's Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda GR8-1291, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.

even though the Workshop Manual procedure was performed properly. This may occur when the existing BSM control module has a hand written suffix on the label. Example: Applicable BSM control module part number DB2R-67-Y80B, where the suffix ("B") is handwritten on the module label: This concern is caused by the wrong suffix being written on the label with an older software version. To eliminate this concern, the production process has been changed.

Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The(BSM) radar aiming is performed whenever the (BSM) control module, the (BSM) bracket or the rear bumper is replaced. The tool is available for loan by contacting DAG.

notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed. This TSB is applicable for the following cases. The oil change due notification does not come on, even after mileage exceeded 10,000 miles. Oil life in the center display is still less than 40% even though the mileage exceeded 7,000 miles. To display "Flexible" setting and "Oil life" on the center screen, select the "Applications" screen, "Maintenance", then "Oil Change" tab. For complete details, refer to the the instructions on MGSS (MAINTENANCE MONITOR OPERATION PROCEDURE).

OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc.) placed on the front passenger's seat.

initialization was not performed correctly before customer delivery.TPMS INITIALIZATION PROCESS: When any of the services below is performed, BE SURE TO INITIALIZE THE TPMS BEFORE DRIVING THE VEHICLE by pushing and holding the TPMS Set Switch on the dash until the TPMS warning light flashes two times and the warning beep sounds once. The TPMS must be initialized in the following cases: 1. Tire pressures have been adjusted in one or more tires. 2. Tires have been rotated. 3. Tires or wheels have been replaced. 4. The vehicle's battery cable has been disconnected for any reason. 5. The vehicle's battery has been discharged. 6. The DSC HU/CM connector has been disconnected for any reason.

close when the ignition is turned ON or OFF. The display operation does not fully open/close. It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the active driving display which activates pinching detection.

close when the ignition is turned ON or OFF. The display operation does not fully open/close. It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the active driving display which activates pinching detection.

Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.

If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.

deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.

Vehicle odometer under 62 miles ? VIN-lock occurs with key ON for 3 minutes or longer. 2. Vehicle odometer over 62 miles ? VIN-lock occurs at key ON. Navigation SD Card Map Update Note: Mazda Toolbox navigation SD card map update can only be performed on a navigation SD card that is VIN-locked. See VIN-lock procecure below.

This concern may also occur when a room fuse is installed in a new vehicle.Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected.CX-3 shown:Vehicles having this concern should have their vehicle repaired using the following procedure.

Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The (BSM) radar aiming is performed whenever the (BSM) control module, the (BSM) bracket or the rear bumper is replaced. The tool is available for loan on Mazda e-Store.

vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area.? Adjacent vehicle (B) driving at same speed, even if the vehicle is still in the alert area. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address these customer concerns.

indicator light on the outer mirror glass does not illuminate. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address this customer concern.

modules detect dirt on the rear bumper surface): DTC U1A4B:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (RH)), DTC U3000:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (LH)), The BSM turns ?OFF? and the BSM OFF indicator turns ?ON? in the instrument cluster while driving, The BSM will not turn on again during the drive cycle, After cycling the ignition switch off and on again, the BSM operates normally, DTC U1A4B:97 or U3000:97 is stored in memory. To correct this problem, the control logic of the BSM control modules has been changed.

if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No. 2 (C) socket covers have not been correctly installed or are missing due to improper prior repairs (i.e., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, HID module seal (D), or missing bumper brackets (E) is not covered by warranty policy.

indicator light on the outer mirror glass does not illuminate. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address this customer concern.

When you encounter a customer with this concern, first verify the condition when the customer noticed this symptom. If the condition is similar to the following "CONTROL LOGIC OF AMBIENT TEMPERATURE" or "DIFFERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS", advise the customer that this is a normal characteristic of the vehicle and not a malfunction. If the condition does not meet the following and the sensor malfunction is suspected, make sure to inspect the sensor according to MGSSonline or Workshop Manual (section 09-22 AMBIENT TEMPERATURE SENSOR INSPECTION). Replace the sensor only when it fails the Workshop Manual inspection.

Operations is 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

Forward Sensing Camera (FSC) and Laser Sensor. Replace the windshield with a new one instead.

modules detect dirt on the rear bumper surface):

THE TEST KIT IS DESIGNED PECIFICALLY FOR SKYACTIV MODULE TERMINALS. THE SST WILL BE SHIPPED BY MAZDAS TOOL VENDOR BOSCH STARTING JANUARY 15, 2016. PROCEDURES FOR USAGE ARE FOUND IN THE SKYACTIV WIRING TERMINAL TEST KIT WBT, COURSE #1649. THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST:

TO COMPLETE THE RADAR AIMING PROCEDURE (IT IS OK TO REPLACE THE LEFT BSM ALONE). REASON IF THE RIGHT-SIDE BSM CONTROL MODULE IS REPLACED ALONE, AUTOMATIC CONFIGURATION IS NOT PERFORMED DUE TO A PROGRAM ERROR IN THE MODULE. BECAUSE OF THIS, THE REQUIRED BSM RADAR AIMING CANNOT BE PERFORMED. AUTOMATIC CONFIGURATION AS WELL AS BSM RADAR AIMING CAN BE PERFORMED, IF THE LEFT-SIDE BSM CONTROL MODULE IS REPLACED ALONE OR TOGETHER WITH THE RIGHT-SIDE BSM CONTROL MODULE.

IS TURNED ON, AND WILL NOT REBOOT. IT WILL ONLY REBOOT AFTER THE IGNITION IS TURNED OFF AND THEN ON AGAIN. THIS IS CAUSED BY AN INTERNAL MALFUNCTION OF THE CONNECTIVITY MASTER UNIT (CMU) HARDWARE. NOTE: IF THE SYSTEM REBOOTS BY ITSELF, THIS TSB IS NOT APPLICABLE. REFER TO TSB 09-022/15 FOR CMU SOFTWARE UPDATE.

TOOL (SST) TO ALLOW FOR THE RADAR AIMING OF THE BLIND SPOT MONITORING (BSM) SYSTEM. THE (BSM) RADAR AIMING IS PERFORMED WHENEVER THE (BSM) CONTROL MODULE, THE (BSM) BRACKET OR THE REAR BUMPER IS REPLACED. THE TOOL IS AVAILABLE FOR LOAN ON MAZDA E-STORE.

TO COMPLETE THE RADAR AIMING PROCEDURE (IT IS OK TO REPLACE THE LEFT BSM ALONE). REASON IF THE RIGHT-SIDE BSM CONTROL MODULE IS REPLACED ALONE, AUTOMATIC CONFIGURATION IS NOT PERFORMED DUE TO A PROGRAM ERROR IN THE MODULE. BECAUSE OF THIS, THE REQUIRED BSM RADAR AIMING CANNOT BE PERFORMED. AUTOMATIC CONFIGURATION AS WELL AS BSM RADAR AIMING CAN BE PERFORMED, IF THE LEFT-SIDE BSM CONTROL MODULE IS REPLACED ALONE OR TOGETHER WITH THE RIGHT-SIDE BSM CONTROL MODULE.

(2) DOOR LOCKS REPEATEDLY LOCK AND UNLOCK WHEN APPROACHING THE VEHICLE WITH THE ADVANCED KEY. (3) KEY WARNING LIGHT (RED) ON WHILE DRIVING AND DTC B10D1:23 AND/OR B10D3:23 IS(ARE) STORED. B10D1:23 REQUEST SWITCH (LF) CIRCUIT MALFUNCTION B10D3:23 REQUEST SWITCH (RF) CIRCUIT MALFUNCTION

TOOL (SST) TO ALLOW FOR THE RADAR AIMING OF THE BLIND SPOT MONITORING (BSM) SYSTEM. THE (BSM) RADAR AIMING IS PERFORMED WHENEVER THE (BSM) CONTROL MODULE, THE (BSM) BRACKET OR THE REAR BUMPER IS REPLACED. THE TOOL IS AVAILABLE FOR LOAN ON MAZDA E-STORE.

IF NOT USED, THE CONTROL MODULE REPROGRAMMING MAY FAIL DUE TO A WEAK VEHICLE BATTERY.THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE PREVENTS THE VEHICLE BATTERY FROM BEING DISCHARGED. THIS ALLOWS THE IDS TO REPROGRAM A CONTROL MODULE WITHOUT INTERFERENCE FROM A WEAK OR UNDERCHARGED VEHICLE BATTERY. NOTE: CONTROL MODULE DAMAGE MAY OCCUR IF THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE IS NOT USED.

THIS MAY BE CAUSED BY AN OBSTRUCTION OF THE FRONT AND/OR REAR LIGHT SENSOR(S) (E.G. HANGING A PARKING PERMIT FROM THE MIRROR). USE A SOFT CLOTH WITH MILD DETERGENT TO CLEAN THE MIRROR. HARSH DETERGENT MAY DAMAGE THE FRONT AND/OR REAR LIGHT SENSOR(S).

IF THE HARNESS IS NOT CONNECTED PROPERLY, THE AD-DISP MAY NOT OPERATE.

ON A SMOOTH ROAD SURFACE EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. PLEASE CONTACT THE HOTLINE FOR A COUNTERMEASURE REPAIR IF A VEHICLE ARRIVES WITH THIS ISSUE. A COUNTERMEASURE CONTROL MODULE IS DUE IN JULY FOR THIS CONCERN.

IF THE HARNESS IS NOT CONNECTED PROPERLY, THE AD-DISP MAY NOT OPERATE.

IF AN AFTERMARKET ALARM SYSTEM IS INSTALLED, THE REAR HARNESS MIGHT HAVE RECEIVED DAMAGE FROM ELECTRO-TAP CONNECTORS (A) OR TO THE PROTECTOR TUBE (B). THIS DAMAGE IS NOT COVERED UNDER WARRANTY.

UNPLUG THE MODULE FOR AT LEAST 10 SECONDS.RECONNECT THE BATTERY, WAIT 60 SECONDS AND THEN HAVE THE CUSTOMER TRY THE APP AGAIN.IF THE VEHICLE STARTS, ORDER MODULE 0000-8F-Z80A.NOTE: THERE IS A LIMITED SUPPLY OF THE MODULE AT THIS TIME, THEREFORE ONLY USE THIS PART FOR THIS SPECIFIC CONDITION.DUE TO THE LIMITED SUPPLY, MAKE SURE YOU WERE SHIPPED THE A LEVEL PART AND NOT THE ORIGINAL PART BEFORE INSTALLING THE PART.INSTALL THE MODULE AND PROGRAM IT PER MMS PROGRAMMING INSTRUCTIONS.INSTRUCT THE CUSTOMER TO UPDATE THEIR ACCOUNT WITH THE NEW MODULE INFORMATION, OTHERWISE THE MMS WILL NOT WORK FROM THE APP.

ON A SMOOTH ROAD SURFACE EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. PLEASE CONTACT THE HOTLINE FOR A COUNTERMEASURE REPAIR IF A VEHICLE ARRIVES WITH THIS ISSUE. A COUNTERMEASURE CONTROL MODULE IS DUE IN JULY FOR THIS CONCERN.

SOME VEHICLES MAY EXPERIENCE MAZDA CONNECT INFOTAINMENT SYSTEM SHUTTING DOWN WITH A FEW MINUTES AFTER IGNITION IS TURNED ON, AND WILL NOT REBOOT. IT WILL ONLY REBOOT AFTER IGNITION IS TURNED OFF AND THEN TURNED ON AGAIN. THIS IS CAUSED BY AN INTERNAL MALFUNCTION OF THE CONNECTIVITY MASTER UNIT (CMU) HARDWARE.

IF RIGHT-DIDE BSM CONTROL MODULE REQURES REPLACEMENT FOR ANY REPAIR, ALSO REPLACE LEFT SIDE BSM CONTROL MODULE TO COMPELTE THE RADAR AIMING PROCEDURE (IT'S OK TO REPLACE THE LEFT BSM ALONE). IF THE RIGHT-SIDE BSM CONTROL MODULE IS REPLACED ALONE, "AUTOMATIC CONFIGURATION" IS NOT PERFORMED DUE TO PROGRAM ERROR IN MODULE. BECAUSE OF THIS, THE REQUIRED "BSM RADAR AIMING" CANNOT BE PERFORMED. "AUTOMATIC CONFIGURATION" AS WELL AS "BSM RADAR AIMING" CAN BE PERFORMED IF LEFT-SIDE BSM CONTROL MODULE IS REPLACED ALONE OR TOGETHER WITH RIGHT-SIDE BSM CONTROL MODULE.

SOME VEHICLES MAY EXHIBIT BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THEHANDLING OF BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CREATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010. CUSTOMERS EXPERIENCING RELATED CONCERNS SHOULD HAVE THEIR VEHICLE AND/OR DEVICE INSPECTED ACCORDING TO THE FOLLOWING PROCEDURE.

The changes are noted in Red text. 01-012/22 10/06/22 DESCRIPTION Some vehicles may exhibit accumulation of dried coolant (1) around the water pipe (2). This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. The accumulated coolant is solidified and plugs the gap in high temperature environment and the seepage is stopped and does not progress. This is normal and does not require a part replacement, clean off the dried coolant from around the pipe with a wire brush. REPAIR PROCEDURE 1. Verify the customer concern. 2. If the above condition is experienced, remove the accumulated coolant around the pipe (1) with a wire brush etc. NOTE: Perform the procedure on the vehicle. No need to remove the water pipe and hoses.

There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. The accumulated coolant is solidified and plugs the gap in high temperature environment and the seepage is stopped and does not progress. This is normal and does not require a part replacement, clean off the dried coolant from around the pipe with a wire brush.

down and needs readjustment of the height position. This concern may be caused by the customer's thigh touching and pushing down the height adjustment lever when getting in or out of the vehicle.

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section once a part is selected. Accessories E-catalog For models prior to 2016: Accessory Parts and Installation Instructions

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method A. Auxiliary Key Trace Cut Method If only one auxiliary key is lost/missing, some key cutting machines can trace cut a new key blank. 1. Trace cut the new auxiliary key blank(s). B. Auxiliary Key Code Cut Method If both auxiliary keys are lost/missing, use this method for cutting new auxiliary key blank(s). 1. Confirm you have access to a Mazda approved key cutting machine. See Mazda Approved Key Cutting Machine table.

A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method

Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.

This may be caused by snow and ice accumulated under the molding when contacting a snow pile. The front step molding structure may not be strong enough to hold under certain conditions.

seat back surface.Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.

https://ecatalog.mazdausa.com

for download.

https://ecatalog.trademotion.com/

license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the resetting tool.

Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.

DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.

Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.

CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the resetting tool.

seat back surface.

THIS MAY BE CAUSED BY INSUFFICIENT ADHESION CAUSING ENLARGED CLEARANCE BETWEEN THE SAIL GARNISH AND THE FRONT SASH MOLDING.

SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.

DTC C1001:92 SETS AS A PAST RECORD FOR LOW VISIBILITY OF THE FORWARD SENSING CAMERA (FSC). IT DOES NOT MEAN THERE IS AN ACTUAL FSC DEFECT. IN SOME CASES THE CUSTOMER MAY HAVE A CONCERN WITH THE LANE DEPARTURE WARNING SYSTEM (LDWS) AND/OR HIGH BEAM CONTROL SYSTEM (HBC). IN OTHER CASES THIS DTC MIGHT BE FOUND WITHOUT A RELATED CUSTOMER CONCERN.

FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.

SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.

FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.

THE 2016 MX-5, 2016 CX-3 AND NEW 2016 CX-9 BSM SYSTEM VEHJICLE DETECTION HAS CHANGED. ALTHOUGH THE OVERALL FUNCTION IS THE SAME AS PREVIOUS VEJHICLES, VEHICLE DETECTION IS DIFFERENT.

SOME CUSTOMERS MAY COMPLAIN THAT THE MANUAL DRIVERS SEAT GRADUALLY MOVES DOWN AND NEEDS RE-ADJUSTMENT OF THE HEIGHT POSITION. THIS CONCERN MAY BE CAUSED BY THE CUSTOMERS THIGH TOUCHING AND PUSHING DOWN THE HEIGHT ADJUSTMENT LEVER WHEN GETTING IN OR OUT OF THE VEHICLE.

To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.

This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.

The rearview mirror (1) rattles up and down (2) while adjusting the mirror. 2. The rearview mirror (1) makes a rattle noise depending on the road surface conditions while driving. This concern is caused during rearview mirror installation. The adhesive is squeezed out between the windshield and the mirror base. The rearview mirror is assembled on top of the overextended adhesive. The adhesive is softened by heat, and loosening screws, results in a rattling concern.

will need to be ordered and installed when replacing the differential. NOTE: The breather threads have a sealant and locking compound that prevents it from being reused. Refer to GEPC for the correct part number of the Differential Breather. The instructions on MGSS will be updated soon to include replacing the breather when replacing the differential with a new unit.

This may be caused by the sun's reflection.

This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.

This is due to poor sealing where rain or other water can enter inside the light. To eliminate this concern, the shape of the front combination light has been changed to improve sealing ability.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

This may be caused by the sun's reflection.

This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below

This is caused by the gap between the roof molding attachment clips and the roof panel not being wide enough to allow paint to be appropriately applied to the roof panel. To eliminate this concern, the shape of the roof molding clip has been changed to enable paint application between the clip's rib and roof during the manufacturing process.

end causing a poor appearance and obstructing the view of the back window.

will need to be ordered and installed when replacing the differential. NOTE: The breather threads have a sealant and locking compound that prevents it from being reused. Refer to GEPC for the correct part number of the Differential Breather. The instructions on MGSS will be updated soon to include replacing the breather when replacing the differential with a new unit.

This may be caused by the sun's reflection.

This may be caused by fixtures located at the center of the cowl grille, which result in higher pressures applied to the windshield. When small pebbles/rocks are caught between the cowl grille and the windshield, deep scratches can lead to a crack in the windshield. To prevent this concern in the future, the cowl grille will be modified to reduce the pressure to the windshield.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.

This may be caused by the sun's reflection.

This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.

This may be caused by fixtures located at the center of the cowl grille, which result in higher pressures applied to the windshield. When small pebbles/rocks are caught between the cowl grille and the windshield, deep scratches can lead to a crack in the windshield. To prevent this concern in the future, the cowl grille will be modified to reduce the pressure to the windshield.

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

color) instead of athe conventional methanol type (blue color). This change is for European compliance Mazda has decided to make the change for all markets.

remedy, and warranty coverage (if applicable).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

This is due to poor sealing where rain or other water can enter inside the light. To eliminate this concern, the shape of the front combination light has been changed to improve sealing ability.

This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may becaused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).

This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

In this case, accessories, such as a roof carrier cannot be installed. Even if the accessory installation was possible, it may cause loose fitting, water leaks or other concerns.

This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.

remedy, and warranty coverage (if applicable).

In this case, accessories, such as a roof carrier cannot be installed. Even if the accessory installation was possible, it may cause loose fitting, water leaks or other concerns. (C) - Bracket Unit. This concern was caused by improper assembly during vehicle production.

lights are on when they start driving around dusk or dawn under low temperatures. At that time, the windshield is clear but the lens of the Forward Sensing Camera (FSC) is foggy. The FSC may not function properly under the following conditions: ? Foggy windshield ? Foggy FSC lens ? Heavy rain, dense fog, snow and direct sun light ? No or poor lane markings. When the FSC control system detects the foggy lens of the camera, the system deactivates LDWS and HBC functions.

lights are on when they start driving around dusk or dawn under low temperatures. At that time, the windshield is clear but the lens of the Forward Sensing Camera (FSC) is foggy. The FSC may not function properly under the following conditions: ? Foggy windshield ? Foggy FSC lens ? Heavy rain, dense fog, snow and direct sun light ? No or poor lane markings. When the FSC control system detects the foggy lens of the camera, the system deactivates LDWS and HBC functions.

other similar tools be used to hold the lift gate stay dampers. Use only the tools specified in the recall. Vice Grips or other similar tools can easily damage the stay dampers. NOTE: Stay damper parts received with Vice Grip marks will not be covered under warranty.

1. Even if there is no vehicle in the alert area, the BSM indicator light on the outer mirror glass illuminates. 2. When a vehicle appears in the alert area, the BSM indicator light on the outer mirror glass illuminates later than expected. 3. BSM indicator light on the outer mirror glass illuminates even when a vehicle is approaching two lanes away (right or left side). This may be caused by a variation of the relative location between the radar emitted by the BSM unit and the rear bumper. An error may occur in the detection angle of the radar.

1. THE BOTTOM OF THE WINDOW SHIELD IS VISIBLE WHEN THE COWL GRILLE IS PUSHED. 2. THE SIDE COVER OF THE COWL GRILLE IS DEFORMED.

CLEARANCE BETWEEN THE REAR SPOILER AND LIFTGATE GLASS. THE EXCESSIVE CLEAR-ANCE MAY CAUSE THE REAR SPOILER TO RATTLE WHEN CLOSING THE LIFTGATE.THE REAR SPOILER PROTECTOR (B) THICKNESS HAS BEEN INCREASED AT PRODUCTION TO IMPROVE FIT BETWEEN REAR SPOILER AND LIFTGATE GLASS (C) TO ILLUMINATE THE NOISE WHEN CLOSING THE LIFTGATE.

THE ISOFIX CONNECTOR(S) (A) OR LATCH SYSTEM TETHER STRAP (C) OF THE CHILD SEAT DOES/DO NOT CATCH THE ANCHOR(S) (B) IN THE VEHICLE. THE ANCHOR(S) IS/ARE OBSTRUCTED BY THE REAR SEAT CUSHION. THE REAR EDGE TRIMMING MATERIAL (D) OF THE REAR SEAT CUSHION IS POSITIONED INCORRECTLY OBSTRUCTING THE ANCHOR(S).

THE ISOFIX CONNECTOR(S) (A) OR LATCH SYSTEM TETHER STRAP (C) OF THE CHILD SEAT DOES/DO NOT CATCH THE ANCHOR(S) (B) IN THE VEHICLE. THE ANCHOR(S) IS/ARE OBSTRUCTED BY THE REAR SEAT CUSHION. THE REAR EDGE TRIMMING MATERIAL (D) OF THE REAR SEAT CUSHION IS POSITIONED INCORRECTLY OBSTRUCTING THE ANCHOR(S).

THIS CONCERN IS MOST LIKELY TO BE FOUND IN COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEN PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED ARE TO REMOVE STAIN(S).

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

Repair the rust and install a pad to prevent future rust. NOTE: This service bulletin is only applicable if the rust started from the marked area (1) around the holes. If rust occurs on other areas, this service bulletin is not applicable.

If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot perform any additional testing of the system. Dealers and customers should never attempt to test or recreate crash scenarios under any circumstances because that could lead to an accident and injuries. NOTE: This article only applies to the applicable vehicles below equipped with SCBS system that uses a Laser Sensor. This article does not apply to newer vehicles equipped with SCBS system that uses a Forward Sensing Camera (FSC).

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

Repair the paint rust and install a pad to prevent future paint rust.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

This concern may be caused when a load, which is applied to the seat during braking, exceeds a specified level and may impact the retaining mechanism of the seat lifter and cause the seat to move downward. To eliminate this concern, the rigidity of the retaining mechanism of the seat lifter has been increased.

Upon inspection, the coil spring is found to be broken at the lower part without any trace of an accident. It may be found during maintenance or service opportunity without customer complaints. Mud and sand caught between the coil spring and the lower spring seat causes paint damage on the coil spring, resulting in rust holes and uneven force application. To correct this issue, the shape of the lower spring seat has been modified.

vehicle service.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit. Tool Number Description Pricing PC1923MAZ Pro-Cut On-Car Brake Lathe Check eStore or call for current pricing OBTAINING TOOLS This tool can be ordered through Mazda eStore. You can log on to eStore at: http://dealers.mazdausa.com CUSTOMER SERVICE INFORMATION For warranty or product information contact Mazda Authorized Service Equipment at 877-768-6657. Customer service representatives are available from 7:30 AM until 7:00 PM CST, Monday through Friday. SPECIAL SERVICE TOOL (SST) PART NAME: OVERVIEW Pro-Cut On-Car Brake Lathe PART NUMBER: PC1923MAZ APPLICABLE MODELS: All USAGE: To machine brake rotors on the vehicle.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.

Upon inspection, the coil spring is found to be broken at the lower part without any trace of an accident. It may be found during maintenance or service opportunity without customer complaints. Mud and sand caught between the coil spring and the lower spring seat causes paint damage on the coil spring, resulting in rust holes and uneven force application. To correct this issue, the shape of the lower spring seat has been modified.

This may be caused by the dust boot having insufficient resistance to the cold. The shape and material of the dust boot has been changed to improve its resistance to cold.

properly initialize the system.The Tire Pressure Monitoring System (TPMS) monitors the tire pressure of all four tires indirectly using the data sent from the ABS wheel speed sensors. If the air pressure of one or more tires is too low compared with the specified value (the initial value learned by the system), the system warns the driver with the TPMS warning light in the instrument cluster and a beep sound. To allow the TPMS to operate correctly, it is essential that the TPMS be initialized to learn new conditions whenever a tire related service is performed.

The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare subject to denial or debit.

vehicle service.

If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.

and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with a vehicle ahead is imminent. In addition, the system reduces damage in the event of a collision by operating the brake control when the system determines that a collision is unavoidable. It may also be possible to avoid a collision depending on the relative speed between your vehicle and the vehicle in front of you. In addition, when the driver depresses the brake pedal, the brakes are applied firmly and quickly to assist.

This is caused by abrasive metal from the front disc plate sticking to the brake pad, which damages the disc plate over time. To correct the problem, a modified brake pad is being used.

This is caused by abrasive metal from the front disc plate sticking to the brake pad, which damages the disc plate over time. To correct the problem, a modified brake pad is being used.

IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.

THIS IS CAUSED BY ABRASIVE METAL FROM THE FRONT DISC PLATE STICKING TO THE BRAKE PAD, WHICH DAMAGES THE DISC PLATE OVER TIME. TO CORRECT THE PROBLEM, A MODIFIED BRAKE PAD IS BEING USED.

THE SEAT CUSHION PAD MAY FALL INTO THE INSIDE OF THE FRAME TEMPORARILY AND MAY BE SHAVED BY THE EDGE OF THE FRAME WHEN IT RETURNS TO THE ORIGINAL POSITION.

THE OWNER'S MANUAL PROVIDES 7 EXAMPLES: OBJECTS ON THE ROAD AT THE ENTRANCE TO A CURVE.VEHICLES PASSING IN THE OPPOSITE LANE WHILE MAKING A CURVE.METAL OBJECTS, BUMPS, OR PROTRUDING OBJECTS ON THE ROAD.WHEN PASSING THROUGH A TOLL GATE.WHEN PASSING UNDER A VINYL CURTAIN OR FLAG.PLASTIC OBJECTS SUCH AS PYLONS.TWO-WHEELED VEHICLES, PEDESTRIANS, ANIMALS OR STANDING TREES.THIS M-TIP ARTICLE PROVIDES 2 ADDITIONAL EXAMPLES:A. THERE IS FOGGING ON THE INNER SURFACE OF THE WINDSHIELD.B. THERE IS/ARE FOGGING/WATER DROPS ON THE OUTER SURFACE OF THE WINDSHIELD.THE NEAR INFRARED LASER BEAM IS A LIGHT BEAM AND IS REFRACTED BY WATER DROPS OR FOREIGN MATERIAL ON THE WINDSHIELD. IN THIS CASE, THE NEAR INFRARED LASER BEAM MAY NOT DETECT AN OBSTRUCTION AHEAD CORRECTLY.

DURING NORMAL MAINTENANCE OR OTHER SERVICE). CHECK THE LABEL ON BOTH REAR SHOCK ABSORBERS FOR THE LOT NUMBER (EXAMPLE: RA5 IS THE LOT NUMBER SHOWN IN THE ILLUSTRATION BELOW). IF THE LOT NUMBERS ARE WITHIN THE PRODUCTION RANGE SHOWN IN THE TABLE BELOW, REPLACE THE REAR SHOCK ABSORBERS WITH NEW ONES.

THE OWNER'S MANUAL PROVIDES 7 EXAMPLES: OBJECTS ON THE ROAD AT THE ENTRANCE TO A CURVE.VEHICLES PASSING IN THE OPPOSITE LANE WHILE MAKING A CURVE.METAL OBJECTS, BUMPS, OR PROTRUDING OBJECTS ON THE ROAD.WHEN PASSING THROUGH A TOLL GATE.WHEN PASSING UNDER A VINYL CURTAIN OR FLAG.PLASTIC OBJECTS SUCH AS PYLONS.TWO-WHEELED VEHICLES, PEDESTRIANS, ANIMALS OR STANDING TREES.THIS M-TIP ARTICLE PROVIDES 2 ADDITIONAL EXAMPLES:A. THERE IS FOGGING ON THE INNER SURFACE OF THE WINDSHIELD.B. THERE IS/ARE FOGGING/WATER DROPS ON THE OUTER SURFACE OF THE WINDSHIELD.THE NEAR INFRARED LASER BEAM IS A LIGHT BEAM AND IS REFRACTED BY WATER DROPS OR FOREIGN MATERIAL ON THE WINDSHIELD. IN THIS CASE, THE NEAR INFRARED LASER BEAM MAY NOT DETECT AN OBSTRUCTION AHEAD CORRECTLY.

This is considered normal and NO repair should be performed. During production, differential ring and pinion gears receive a manganese phosphate coating (commonly referred to as black oxide). This coating forms a porous, oil-retentive surface that improves boundary lubrication and reduces adhesive wear during initial contact cycles. Designed as a sacrificial layer, it is gradually removed under load throughout the break-in process. As a result, after the first few hundred miles, or at the initial gear oil service interval, the lubricant may appear darkened by the worn-off coating. It will contain trace ferrous particles from the normal run-in of the gear teeth and bearing surfaces. This condition is expected and does not, by itself, indicate an issue with the differential or PTO gears.

essential to first classify the issue into one of three primary categories: Noise, Vibration, or Harshness. Many customer complaints may involve overlapping symptoms, such as both noise and vibration, so identifying the dominant characteristic is critical. Once the primary symptom is determined, follow the appropriate diagnostic path. For example, if a concern includes both noise and vibration but is related to vehicle speed, the vibration diagnostic path should be followed. When considering component replacement during the diagnostic process, it is best practice to start with the lowest cost or most accessible part unless diagnostic evidence clearly identifies a more expensive or complex component as the root cause. This approach helps minimize repair costs and avoids unnecessary part replacements. For example, a growling or bearing whine noise may be mistakenly attributed to internal components in the differential, transfer unit, or transmission, when the actual source is a wheel bearing. Misdiagnosis like this can lead to unnecessary repairs, added time and cost. To help prevent this, always follow the guidelines in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

This concern may be caused by insufficient lubrication between the worm wheel gear and worm shaft. To eliminate this concern, the amount of grease between the worm wheel gear and worm shaft was increased and the housing end cover shape was modified.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.

Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.

Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally.

This concern may be caused by insufficient lubrication between the worm wheel gear and worm shaft. To eliminate this concern, the production process for the steering shaft has been modified.

The system performance has been improved as follows: Ver. 74.00.324 fixes these software errors (bugs): * If the shift lever is operated quickly while displaying the CarPlayTM screen, the rear view screen may not return to the CarPlayTM screen. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into the R position.

Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

configuration.

As the vehicle mileage increases, the ATF color changes. The color change does not affect vehicle performance.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Use a clean towel damped in leather/vinyl cleaner or mild soap to clean the steering wheel. NOTE: Upholstery maintenance and care information can also be found in the Owner's Manual.

resistance and/or an unusual noise when turning the steering wheel in either direction. This concern may be caused by the following causes. - The worm wheel gear was out of concentricity tolerance due to an improper manufacturing process. - The worm wheel gear was not in the proper distance due to an improper tolerance range. - The worm wheel gear has been swelled by water due to improper storage at the factory. To eliminate this concern, the production process for the steering shaft has been further modified. Customers having this concern should have their vehicle repaired using the following repair procedure.

This concern may be caused by the following causes. The worm wheel gear was out of concentricity tolerance due to an improper manufacturing process. The worm wheel gear was not in the proper distance due to an improper tolerance range, The worm wheel gear has been swelled by water due to improper storage at the factory, To eliminate this concern, the production process for the steering shaft has been further modified.

transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

This concern may be caused by insufficient lubrication of the gear due to uneven and deteriorated grease. To eliminate this concern, the production process for the steering shaft has been further modified.

The noise: Depends on the vehicles speed only (the more speed, the more noise) Occurs with all types of driving (acceleration, deceleration, steady speed) Does not depend on rpm, gear, or ATF temperature

Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally.

and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order to re-install the original plug from the old transmission.

This concern may be caused by insufficient lubrication of the gear due to uneven and deteriorated grease. To eliminate this concern, the production process for the steering shaft has been further modified.

NOTE: The following Caution is included with every ATX that requires configuration.

Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the oil cooler was missing altogether. IMPORTANT NOTE: ALWAYS REMEMBER TO INCLUDE THE ORIGINAL OIL COOLER WITH THE RETURNED TRANSMISSION CORE!

This concern may be caused by insufficient lubrication of the gear due to uneven and deteriorated grease. To eliminate this concern, the production process for steering shaft has been modified.

of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.

The noise: Depends on the vehicles speed only (the more speed, the more noise)Occurs with all types of driving (acceleration, deceleration, steady speed)Does not depend on rpm, gear, or ATF temperature.This is caused by a damaged bearing in the transaxle due to improper configuration of the transaxle case. A modification has now been implemented on automatic transaxles with the following serial numbers: 7TN0820364 and higher (CX-3) / 8TN1090104 and higher (except CX-3) 8TR1008883 and higher 8TD1003276 and higher 8T50331192 and higher (CX-3) / 8T50329705 and higher (except CX-3).

This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the driveshaft. To correct this issue, the thickness of the dust cover has been increased.

This concern may be caused by insufficient lubrication of the gear due to uneven and deteriorated grease. To eliminate this concern, the production process for steering shaft has been modified.

This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the drive shaft. To correct this issue, the thickness of the dust cover has been increased.

configuration.

This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the driveshaft. To correct this issue, the thickness of the dust cover has been increased.

Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.

ONLY USE ATF-FZ TO FILL OR TOP OFF THE FLUID LEVEL. ATF-FZ IS SPECIALLY DESIGNED FOR USE IN THE SKYACTIV-DRIVE SERIES AT. IT IS A LOW VISCOSITY FORMULA WITH LESS FRICTION FOR BETTER FUEL ECONOMY. NOTE: ATF-FZ IS COLORED BLUE FOR EASY IDENTIFICATION. TO CHECK THE FLUID LEVEL, REMOVE THE BOLT, THEN REMOVE THE DIPSTICK. THE DIPSTICK IS MARKED WITH A FZ ON SKYACTIV-DRIVE FW6A-EL AT. WHEN FINISHED, INSERT THE DIPSTICK AND INSTALL THE BOLT.

THIS IS DUE TO A DECREASE OF ADHESIVE FORCE UNDER HIGH AMBIENT TEMPERATURES. THE WHITE FELT HAS SHIFTED FROM ITS ORIGINAL POSITION. TO ELIMINATE THIS CONCERN, THE SHAPE AND THE POSITION OF THE WHITE FELT HAVE BEEN CHANGED.

THIS IS DUE TO A DECREASE OF ADHESIVE FORCE UNDER HIGH AMBIENT TEMPERATURES. THE WHITE FELT HAS SHIFTED FROM ITS ORIGINAL POSITION. TO ELIMINATE THIS CONCERN, THE SHAPE AND THE POSITION OF THE WHITE FELT HAVE BEEN CHANGED.

SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owners Manual, Workshop Manual, Technical Service Bulletin, etc.).

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface.

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Some customers may complain that it is difficult to lock the rear seat back (RH) to the upright position. The right side seat back weight is lighter than the left side. The lighter right side requires more force to lock the seat back to the upright position.

driving on a smooth road surface even if the TPMSF system has been properly initialized at the specified tire air pressure.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Use the information below to troubleshoot the customers complaint: MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE CANNOT COMMUNICATE WITH VEHICLE ERROR MESSAGE INSTALLED ON ANDROID DEVICES COMMUNICATION ERRORS MMS CHECK MODE - Use to verify system operation (see below).

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

longer has access or service." for the MMS APP installed on android devices starting 8/1/18. Inform the customer that all they need to do is update the MMS APP to the latest version to get rid of the error message.

Radar units are configured to the original vehicle, and if installed in another vehicle, a configuration error will occur. Refer to MGSS (RADAR UNIT INSPECTION) for proper diagnosing.

NOTE: You may see ?Selection not available? on IDS when a selecting ?Programming menu?, 108.07 included a timer extension for Programming menu application that had to be installed before the expiration date of 3/27/18. After the expiration, IDS can?t accept the extension. To correct this, uninstall IDS and re-install IDS 108.00 >IDS 108.07 up-date. Select "Remove Mazda data files and settings" as shown below.

The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear incertain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.

Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.

Damage can occur when using some cleaners that contain strong acid, alkaline cleanser or organic solvent. Damage caused by using these cleaners is not covered by Mazda's New Vehicle Limited Warranty term.

THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMP-TOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM.

MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNERS MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDAS FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.

SURFACE EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. THE TPMS SYSTEM MAY HAVE BEEN IMPROPERLY INITIALIZED WHEN THE INITIALIZATION WAS PERFORMED ON CERTAIN TYPES OF ROUGH ROAD SURFACES. THEN, WHEN DRIVEN ON SMOOTH ROAD SURFACES, THE TPMS SYSTEM MAY DETECT IMPROPER TIRE AIR PRESSURE. THE DSC HU/CM CONTROL LOGIC HAS BEEN CHANGED FOR THIS CONCERN.

SURFACE EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. THE TPMS SYSTEM MAY HAVE BEEN IMPROPERLY INITIALIZED WHEN THE INITIALIZATION WAS PERFORMED ON CERTAIN TYPES OF ROUGH ROAD SURFACES. THEN, WHEN DRIVEN ON SMOOTH ROAD SURFACES, THE TPMS SYSTEM MAY DETECT IMPROPER TIRE AIR PRESSURE. THE DSC HU/CM CONTROL LOGIC HAS BEEN CHANGED FOR THIS CONCERN.

SURFACE EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. THE TPMS SYSTEM MAY HAVE BEEN IMPROPERLY INITIALIZED WHEN THE INITIALIZATION WAS PERFORMED ON CERTAIN TYPES OF ROUGH ROAD SURFACES. THEN, WHEN DRIVEN ON SMOOTH ROAD SURFACES, THE TPMS SYSTEM MAY DETECT IMPROPER TIRE AIR PRESSURE. THE DSC HU/CM CONTROL LOGIC HAS BEEN CHANGED FOR THIS CONCERN.

be wet.

be wet.

be wet.

This includes the use of intermediate positions.

Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.

This may be caused by condenser corrosion, causing a refrigerant leak.

WARRANTY EXTENSION".

extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date, with no mileage limitation. Concern Outline On certain subject CX-3 vehicles, the A/C condenser may be corroded, causing an A/C refrigerant leak. Vehicles with this condition may exhibit no cool air from the climate control vents when the A/C is ON. This warranty extension program applies only to the repair of the A/C condenser with this concern.

extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date, with no mileage limitation. Concern Outline On certain subject CX-3 vehicles, the A/C condenser may be corroded, causing an A/C refrigerant leak. Vehicles with this condition may exhibit no cool air from the climate control vents when the A/C is ON. This warranty extension program applies only to the repair of the A/C condenser with this concern. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures.

This may be caused by condenser corrosion, causing a refrigerant leak. The manufacturer of the condenser has been changed and the configuration of the condenser tube has been improved.

This may be caused by condenser corrosion, causing a refrigerant leak. The manufacturer of the condenser has been changed and the configuration of the condenser tube has been improved.

This may be caused by condenser corrosion, causing a refrigerant leak. The manufacturer of the condenser has been changed and the configuration of the condenser tube has been improved.

This may be caused by condenser corrosion, causing a refrigerant leak.The manufacturer of the condenser has been changed and the configuration of the condenser tube hasbeen improved.

lights ON due to foggy FSC lens will be reduced. However, the warning message will be displayed on the Multi-Information Display (MID) or the center display when FSC lens is foggy. ? The foggy FSC lens may occur at some weather conditions and is not caused by a defect of the parts. When the warning message is displayed, drive the vehicle for 10 minutes or more with the defroster ON to defogthe FSC lens.

UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR).OTE FOR CUSTOMER: THE FSC MAY NOT WORK PROPERLY UNDER THE CONDITIONS:THE WINDSHIELD IS NOT CLEAR. THE FSC LENS IS NOT CLEAR. DRIVING IN HEAVY RAIN, DENSE FOG OR SNOW, OR INTO THE SUN. DRIVING ON A ROAD WITH NO OR BLURRED ROAD LANE MARKINGS. WHEN THE WINDSHIELD BECOMES FOGGY IN THE WINTER TIME OR OTHER COLD WEATHER CONDITIONS AND LDWS/HBC WARN-ING LIGHTS TURN ON, DRIVE WITH THE DEFROSTER ON FOR ABOUT 10 MINUTES. THIS WILL HELP CLEAR THE FOGGY WINDSHIELD AT THE FSC.

.THE CHATTERING NOISE MAY BE CAUSED BY THE VENTILATOR GRILLE SLIPPING OUT OF POSITION AND THE OUTER EDGE CONTACTS THE DASHBOARD. THIS CONCERN MAY OCCUR WITH ANY VENTILATOR GRILLE(S). TO PREVENT THE VENTILATOR GRILLE FROM SLIPPING OUT, THE SHAPE OF THE DASHBOARD HAS BEEN CHANGED.

THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.

THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.

UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR).OTE FOR CUSTOMER: THE FSC MAY NOT WORK PROPERLY UNDER THE CONDITIONS:THE WINDSHIELD IS NOT CLEAR. THE FSC LENS IS NOT CLEAR. DRIVING IN HEAVY RAIN, DENSE FOG OR SNOW, OR INTO THE SUN. DRIVING ON A ROAD WITH NO OR BLURRED ROAD LANE MARKINGS. WHEN THE WINDSHIELD BECOMES FOGGY IN THE WINTER TIME OR OTHER COLD WEATHER CONDITIONS AND LDWS/HBC WARN-ING LIGHTS TURN ON, DRIVE WITH THE DEFROSTER ON FOR ABOUT 10 MINUTES. THIS WILL HELP CLEAR THE FOGGY WINDSHIELD AT THE FSC.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

road.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

Customers having this concern should have their vehicle repaired using the following repair procedure.

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?

This concern may be caused by an insufficient wear resistance of the steering wheel surface.

be caused by an insufficient wear resistance of the steering wheel surface.

A VIBRATION IS FELT AT THE STEERING WHEEL WHEN THE NOISE OCCURS. THIS CONCERN MAY BE CAUSED BY A LACK OF GREASE APPLICATION TO THE SPLINES OF THE INTERMEDIATE SHAFT AT THE PRODUCTION LINE. THE GREASE APPLICATION PROCESS HAS BEEN IMPROVED.

Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. E85: A blend of 85% ethanol and 15% gasoline All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V.

This may be caused by improper brazing (A) of the evaporator (B), causing a refrigerant leak from the joint between the tubes (C) and the header (D). To eliminate this concern, the configuration of the brazing set up has been improved.

This may be caused by improper brazing (A) of the evaporator (B) causing a refrigerant leak fr om the joint between the tubes and the header (D)

Some customers may complain that it is difficult to adjuust the cabin temperature using the auto A/C. This may be more noticeable when the outside temperature is approximately 50 degrees Fahrenheit (10 Ceisius)

Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).

This may be caused by improper brazing of the evaporator, causing a refrigerant leak from the joint between the tubes and the header.

This may be caused by improper brazing (A) of the evaporator (B), causing a refrigerant leak from the joint between the tubes (C) and the header (D).

Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).

This may be more noticeable when the outside temperature is approximately 50 degrees Fahrenheit (10 Celsius).

FAHRENHEIT (0 DEGREES CELSIUS).THE ACCELERATOR PEDAL HAS BEEN CHANGED TO INCREASE DURABILITY.

INSTEAD, THE WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING EVAP LEAK TESTER WILL BE USED TO TROUBLESHOOT EVAP SYSTEM LEAKS.

THE NOISE CAN BE HEARD AT A STOP OR WHILE DRIVING. THIS MAY BE CAUSED BY AN EVAP HOSE MAKING CONTACT WITH THE VEHICLE UNDERBODY.

THE NOISE CAN BE HEARD AT A STOP OR WHILE DRIVING. THIS MAY BE CAUSED BY AN EVAP HOSE MAKING CONTACT WITH THE VEHICLE UNDERBODY.

The following are possible causes of floor mat interference, which can be avoided with proper usage.

However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts. CAUTION: Be aware that when cleaning the brand emblem, never use cleaning products that are highly acidic/alkaline detergent, organic solvents or those with aggressive chemical products, otherwise, the brand emblem may become cracked and/or deformed (as shown in the example below). Always refer customers to the owners manual for proper cleaning using cold or lukewarm water and a mild, neutral detergent.

The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.

User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. We apologize for any inconvenience this may have caused you or your dealer.

SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.THIS SERVICE BULLETIN IS ONLY FOR SUBLET REPAIR. A QUALIFIED UPHOLSTERY REPAIR SPECIALIST IS REQUIRED FOR THIS REPAIR PROCEDURE. PLEASE PRINT A COPY OF THIS BULLETIN FOR THE UPHOLSTERY REPAIR SPECIALIST.

SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.THIS SERVICE BULLETIN IS ONLY FOR SUBLET REPAIR. A QUALIFIED UPHOLSTERY REPAIR SPECIALIST IS REQUIRED FOR THIS REPAIR PROCEDURE. PLEASE PRINT A COPY OF THIS BULLETIN FOR THE UPHOLSTERY REPAIR SPECIALIST.

74.00.311 or later).

of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.352 or later).

uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.

Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version.

The new version number is 59.00.502. Please refer to TSB 09-017/17 for a list of improvements to the system.

If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.

If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.

If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.

IF ANY TYPE OF GREASE OR LUBRICATION IS APPLIED TO THE BUSHINGS, IT MAY CREATE NOISE DUE TO BUSHING SLIPPAGE.

THIS MAKES IT DIFFICULT TO CHANGE THE SEAT BACK RECLINING POSITION. THIS MAY BE CAUSED BY A RETURN RECLINER LEVER KNOB SPRING (A) THAT IS TOO STRONG

IF ANY TYPE OF GREASE OR LUBRICATION IS APPLIED TO THE BUSHINGS, IT MAY CREATE NOISE DUE TO BUSHING SLIPPAGE.

This may be caused by a loose spare tire jack.

This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.

THE VEHICLE CAN SLIP OFF THE JACK AND SERI-OUSLY INJURE SOMEONE. IN THIS SERVICE INFORMATION, SOME IMPORTANT WARNINGS AND CAUTIONS HAVE BEEN TAKEN FROM THE OWNERS MANUAL. FOR MAZDA CUSTOMERS WHO HAVE QUESTIONS ABOUT SAFELY LIFTING THEIR VEHICLE TO CHANGE A FLAT TIRE OR TO INSTALL SNOW CHAINS, PLEASE PROVIDE A COPY OF THE ATTACHED HANDOUT FOR THEM. ALSO, BE SURE TO ALWAYS DIRECT CUSTOMERS TO FOL-LOW THE DIRECTIONS IN THE OWNER'S MANUAL.

THIS MAY BE CAUSED BY A LOOSE SPARE TIRE JACK.

downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. When parked, new messages can be displayed or read by the system. When driving, new messages can be read to the vehicle occupants.

downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. When parked, new messages can be displayed or read by the system. When driving, new messages can be read to the vehicle occupants.

Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.