2021 Lincoln Navigator TSBs

Expedition, Bronco Sport, Explorer, Bronco, Navigator, and Aviator Vehicles Powertrain Control Module Software Update

App Lincoln App including but not limited to: missing activation prompt pop-upon the vehicle's center display screen when attempting to activate vehicle through The Ford App Lincoln App, incorrect location global positioning system GPS reported through The Ford App Lincoln App, problems with remote commands being performed through The Ford App Lincoln App and or incorrect data information reported on The Ford App Lincoln App. These symptoms will be accompanied by diagnostic trouble code DTC B156D 89 in the TCU. This may be due to the accessory protocol interface module APIM software. To correct the condition, update the APIM software.

with phone-as-a-key may exhibit various phone-as-a-key concerns with diagnostic trouble codes (DTC) U200D:15, U200E:15, U200F:15, B1589:31/49 through B1598:31/49, B1A56:31/49, B1D55:31/49, and/or B15A5:56 stored in the remote function actuator (RFA) module. If any of these DTCs are detected during diagnostics, clear the DTCs, reprogram the RFA to the latest software level and start a new Ford Diagnosis and Repair System (FDRS) session. Verify that DTCs are no longer present. If only the B1589:31/49 through B1598:31/49, B1A56:31/49, B1D55:31/49, and/or B15A5:56 DTCs return in the RFA after a self-test, follow normal Workshop Manual (WSM) diagnostics in Section 419-01. Repair as necessary outside of this article. For claiming, use causal part 14G617 and labor operations 12651D and 12651D4.

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

display screen at start-up using Apple CarPlay or Android Auto. This does not affect rear camera operation. This may be due to interference from the phone being connected into the media hub using a universal serial bus (USB) cable during SYNC system boot up. To correct his condition, advise the customer to disconnect the USB cable from the phone. If the center display screen displays normally, reconnect the phone. If the concern persists, disconnect the phone from the USB cable, cycle the ignition off and open the driver's door so the interior lights come on. Close the door, start the vehicle and wait for the center display screen to boot up past the start-up animation and display the home screen, then reconnect the phone using the USB cable. If the concern persists after this procedure, follow normal Workshop Manual diagnostics for a blank screen concern.

toggle button in the Connectivity setting menu grayed out with an inability to switch it off.

the SYNC software, you may experience SYNC system instability concerns and/or a failure to preserve certain settings across ignition cycles. This may result in a black infotainment screen that does not affect rear view camera, incorrect language setting, erased or unsaved radio presets, and potential inability to perform software updates.

concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software

using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt.

using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level

Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.

diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking for an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Confirm FPCM connector (Explorer - C3239, Transit - C433, F-150 - C460/C4336, Expedition/Navigator - C433/C4033) is fully seated and inspect applicable grounds (Explorer  G302, Transit - G401, F-150 - G401, Expedition/Navigator - G403/G406) prior to performing guided diagnostics or replacing any components.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Some 2018-2021 Navigator vehicles may exhibit a grinding, growling, or clicking noise or inoperative power steering column during telescoping/raking operation. This may be due to a body control module B (BCMB) software issue. To correct the condition, follow the Service Procedure to reprogram the BCMB module and replace the steering column telescope or rake actuators.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer  G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to high sulfur content in the fuel. To correct the condition, follow the Service Procedure to de-sulfate the catalytic converters.

Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0932:17. Check the condition of the wiring harness and connections at the ELSD and the differential control module rear (DCMR). If no problems are found, clear the DTC and test drive. If the condition returns, refer to Workshop Manual (WSM), Section 205-02B.

features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Maverick vehicles may exhibit the wireless charger inoperative or poor performance when using some Apple iPhone models that use MagSafe wireless charging including iPhone 12 and 13. This may be due to limited compatibility with the wireless accessory charging module (WACM). To correct the condition, follow the Service Procedure to update the WACM. Note: The WACM software is designed to improve the compatibility between some Apple MagSafe charging iPhones, including iPhone 12 and 13 models, and the Ford Qi wireless charging module.

column during telescoping/raking operation. This may be due to the steering column telescope or rake actuators. To correct the condition, follow the Service Procedure to replace the steering column actuators and reprogram the column and pedal memory module (BCMB).

features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to high sulfur content in the fuel. To correct the condition, follow the Service Procedure to de-sulfate the catalytic convertors.

exhibit Phone-as-a-Key concerns and have diagnostic trouble code(s) (DTC) U200D:15, U200E:15, U200F:15, B15**:31, B15**:49 and/or B15A5:56 stored in the remote function actuator (RFA) module. If the vehicle is exhibiting other symptoms outside of Phone-as-a-key concerns, address those first. If any of these DTCs are detected during diagnostics, clear the DTCs, reflash RFA to the latest software level and start a new Ford Diagnosis and Repair System (FDRS) session. Verify that DTCs are no longer present. If only the B15**:31, B15**:57 and/or B15A5:56 DTC(s) returns in the RFA after a self test, follow normal Workshop Manual (WSM) diagnostics, Section 419-01C.

diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer  G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

exhibit a diagnostic trouble code (DTC) P0932:16. Check the condition of the wiring harness and connections at the ELSD and the differential control module rear (DCMR). If no problem is found, replace the DCMR according to the model years. Refer to Workshop Manual (WSM), Section 205-02B. For claiming, use causal part number 4C016.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option

Diagnostic Trouble Codes (DTCs) P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2022 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

The vehicle may also exhibit the auto dimming rear view mirror becoming dark as soon as the key is turned on or is inoperative. This may be due to incorrect wiring of an aftermarket 5 pin jumper connector from a non-Ford windshield supplier that is causing a short to ground. To correct this condition, inspect if the windshield was recently replaced and verify the circuits in the 5 pin jumper connector located between connector C9440 and C9224 are routed in the correct pin location and adjust as necessary. Refer to the Wiring Diagram, Cell 124-10.

trouble codes (DTCs) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to high sulfur content in the fuel. To correct the condition, follow the Service Procedure to de-sulfate the catalytic convertors.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

Phone-as-a-Key concerns and have diagnostic trouble code(s) (DTC) U200D:15, U200E:15, U200F:15, B15**:31, B15**:49 and/or B15A5:56 stored in the remote function actuator (RFA) module. If the vehicle is exhibiting other symptoms outside of Phone-as-a-key concerns, address those first. If any of these DTCs are detected during diagnostics, clear the DTCs, reflash RFA to the latest software level and start a new Ford Diagnosis and Repair System (FDRS) session. Verify that DTCs are no longer present. If only the B15**:31, B15**:57 and/or B15A5:56 DTC(s) returns in the RFA after a self test, follow normal Workshop Manual (WSM) diagnostics, Section 419-01C.

remote function actuator (RFA) module preventing paring-connecting any phone as a key to the vehicle. If this DTC is detected during pre-delivery inspection (PDI) or while diagnosing phone as a key pare/connection issue, remove the RFA fuse or disconnect the battery terminals for minimum of 5 minutes then reinstall. Start a new FDRS session and verify that U3000:49 is no longer present. Ensure that phone as a key is enabled and a phone can be paired to the vehicle. If the concern is still present, follow normal diagnostics procedures in Workshop Manual (WSM), Section 419-01C.

symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

have diagnostic trouble code(s) (DTC) U200D:15, U200E:15, U200F:15, B15**:31, B15**:49 and/or B15A5:56 stored in the remote function actuator (RFA) module. If any of these DTCs are detected during normal diagnostics, clear the DTCs, reflash RFA to the latest software level and start a new Ford Diagnosis and Repair System (FDRS) session. Verify that DTCs are no longer present. If only the B15**:31, B15**:57 and/or B15A5:56 DTC(s) returns in the RFA after a self test, follow normal Workshop Manual (WSM) diagnostics, Section 419-01C.

Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.

an SSM or TSB is published for a software update. This may be due to the module already being at the latest software level. A later software level may have been programmed at the assembly plant, during a previous dealer visit or by an over the air (OTA) update for vehicles that have automatic updates enabled in the SYNC system settings. To review a vehicle's OTA update history, visit the Connected Vehicle > OTA Dashboard tab in OASIS. Information about the OTA Dashboard can be found on FMCDealer.com when performing a search on OTA History Job Aid.

exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0932:17. Check the condition of the wiring harness and connections at the ELSD and the differential control module rear (DCMR). If no problems are found, clear the DTC and test drive. If the condition returns, refer to Workshop Manual (WSM), Section 308-07A.

Escape/Explorer/SuperDuty/Transit/Aviator/Corsair, 2021 Bronco Sport/F-150/Mustang/Mach-E the Workshop Manual (WSM) diagnostics may direct to replace a module on vehicles that use Ford Diagnosis and Repair System (FDRS). First, an FDRS session must be created on the vehicle prior to removing the faulted module. Once the session is started, run the Programmable Module Installation and replace the module only when instructed by FDRS. Installing a new module prior to starting a scan tool session may result in incomplete module configuration with DTCs U2100, U2101 and/or U2200. Once a session has been started, continue to follow normal WSM procedures to repair the vehicle.

DTC P025A And/Or DTC U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds(F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2021 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2021 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

> Front Seats > Diagnosis and Testing lead to the replacement of the front seat cushion extension adjuster, a lower-level part is now available (14C720). It is not necessary to replace the front seat cushion extension adjuster if only the front seat cushion extension motor assembly is damaged. For Corsair, use service part LJ7Z-14C720-A. For Aviator, use service part R2TZ-14C720-A. For 2025-2026 Navigator (both sides) and 2018-2024 Navigator driver side, use service part NL7Z-14C720-A. For 2018-2024 Navigator passenger side, use service part NL7Z-14C720-B.

after an over the air (OTA) update. The message can be cleared from the center display screen and SYNC can be used normally, but it will re-appear at every subsequent ignition cycle. Inform customers that engineering is currently working on a software update solution for this condition to be delivered OTA expected in late Q3 2026. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Monitor Professional Technician System (PTS) for additional information.

code (DTC) P0299 stored in the powertrain control module (PCM) and may also exhibit a rattle noise from the turbocharger. This may be due to the wastegate actuator rod being disconnected. Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls > Turbocharger has been added to address this condition to allow servicing of the turbocharger actuator rod. In addition, the wastegate actuator rod and associated retention springs and clips have been released as lower level components to complete the repair without replacing the entire turbocharger actuator assembly.

Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L/3.5L (non hybrid)/6.8L/7.3L engine and 2021-2026 E-Series may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated to address this condition. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.

Reason for update: update the Part List Description and Labor Times Description Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM) This may be due to axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary to confirm proper function. Add a new line to the repair order

Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L,3.5L EcoBoost (non-hybrid), 3.5L Cyclone, 6.8L or 7.3L engine, may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.

rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine to transmission spacer plate (separator plate). To correct this condition, inspect the engine to transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replacement of the torque converter is not necessary. Replace only the engine to transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 > Engine to Transmission Spacer Plate for full spacer plate removal and installation. When reinstalling the starter motor, make sure the starter is flush with the engine to transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging the newly installed engine to transmission spacer plate.

Reason for update: update the Part List and Service Procedure Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM) This may be due to axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary to confirm proper function. Add a new line to the repair order to document any additional

noise at idle and/or while driving.

Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang, 2019-2023 Ranger vehicles equipped with a 10R80 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang, 2019-2023 Ranger vehicles equipped with a 10R80 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.

Some 2018-2021 Expedition/Navigator and 2020-2021 Explorer/Aviator vehicles equipped with a 10R80/10R80 MHT or 10R60 (excluding Police Interceptor vehicles with column shift) may exhibit a momentary transmission neutral-out condition while in drive. Vehicle may also have diagnostic trouble code (DTC) P07E6 and/or P07E4 stored in the powertrain control module (PCM) or transmission control module (TCM) and/or a possible audible noise. This may be due to a leak in the park valve circuit. To correct the condition, follow the Service Procedure to inspect the park system hardware for wear or damage and replace the valve body separator plate with an improved valve body separator plate.

noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report if there is a customer concern of whine noise describing operating conditions and noise severity.

Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60/10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.

lamp (MIL) and low oil pressure warning in the instrument panel cluster (IPC), with diagnostic trouble codes (DTC) P0521 and/or P0524 in the powertrain control module (PCM). This condition may be caused by an internal oil pressure leak. If pinpoint test E in the Workshop Manual (WSM) Section 303-01B directs you to the replacement of the oil pump, upon reassembly inspect that the main oil gallery tube (6718) is assembled and aligned properly on the back of the engine front cover. The engine oil gallery seal (00815) must be replaced any time the front cover is removed (per WSM Section 303-01B). The WSM front cover removal and installation procedure is in the process of being updated.

For any missing labor operations, claim available new model labor operations or m-time. Refer to this article on the repair order. When replacing the CDF cylinder, the current TSB does not require a complete transmission overhaul or cooler and converter flushing. Ford is currently reviewing the TSB. Monitor OASIS for updates.

Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2023 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the keep alive memory in the PCM/TCM or the transmission main control valve body. To correct the condition, follow the Service Procedure to overhaul the main control valve body and/or perform an adaptive learning drive cycle.

2021-2023 Bronco vehicles equipped with a 10R60 transmission and built on or before 23-Dec-2022 or with a 18R80/10R80MHT transmission and built on or before 15-Aug-2022 may exhibit a harsh/delayed engagement and/or harsh/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the PCM or TCM, the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

exhibit a momentary transmission neutral-out condition while in drive. Vehicle may also have diagnostic trouble code (DTC) P07E6 and/or P07E4 stored in the powertrain control module (PCM) or transmission control module (TCM) and/or a possible audible noise. This may be due to a leak in the park valve circuit. To correct the condition, follow the Service Procedure to inspect the park system hardware for wear or damage and replace the valve body separator plate with an improved valve body separator plate.

automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware break-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.

noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability.

automatic transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P163E stored in the powertrain control module (PCM) or transmission control module (TCM) after replacing the main control valve body. This may be due to software incompatibility between the replacement main control valve body solenoid strategy file and the PCM/TCM software. To correct this condition, follow the Service Procedure to enter only the 13-digit solenoid body strategy when downloading transmission strategy.

exhibit a momentary transmission neutral-out condition while in drive. Vehicle may also have diagnostic trouble code (DTC) P07E6 and/or P07E4 stored in the powertrain control module (PCM) or transmission control module (TCM) and/or a possible audible noise. This may be due to a leak in the park valve circuit. To correct the condition, follow the Service Procedure to inspect the park system hardware for wear or damage and replace the valve body separator plate with an improved valve body separator plate.

or before 14-Mar-2022 equipped with a 3.5L EcoBoost engine may experience a coolant leak at the thermostat housing. This may be due to an incomplete weld on the thermostat housing which can leak during normal vehicle operation. To correct the condition, replace the thermostat housing using service part number ML3Z-8A586-C. Refer to Workshop Manual (WSM), Section 303-03. For claiming, use causal part 8A586 and applicable labor operations in Section 08 of the Service Labor Time Standards (SLTS) Manual.

malfunction or an inoperable condition with the power roof opening panel or sunshade where the initialization procedure may need to be performed. The Workshop Manual (WSM), Section 50117 > General Procedures > Power Roof Opening Panel Initialization is the process of being updated. At this time, when directed in Step 1 to switch the ignition ON, the engine should then be started and allowed to run. When Step 2 is reached and the vehicle is turned back on, the engine should be restarted and allowed to run through completion of the initialization procedure.

memory function or when manually adjusting the power tilt or telescoping functions of the steering column. This noise may be caused by the steering column tilt or telescopic motors. Refer to Workshop Manual Section 211-04, General Procedures > Steering Column Motor Lubrication. Follow the steps to address the noise through lubrication. If the noise persists, replace the suspect motor as directed by the Workshop Manual. These motors are both serviceable separately from the steering column assembly.

automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware break-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.

conditioning (A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor.

Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.

(A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor.

automatic transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P163E stored in the powertrain control module (PCM) or transmission control module (TCM) after replacing the main control valve body. This may be due to software incompatibility between the replacement main control valve body solenoid strategy file and the PCM/TCM software. To correct this condition, follow the Service Procedure to obtain a new main control valve body with a new strategy number.

Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.

Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.

SYNC screen when adjusting the climate control temperature. This may be due to the SYNC software installed in the accessory protocol interface module (APIM). Engineering is currently developing a software update that is expected in January 2022. Once the software update is available, it will be made available to customers who have enabled SYNC 3 Automatic Updates with their vehicle connected to a Wi-Fi network. Repair appointments should be scheduled for customers in February 2022 who do not receive Automatic Updates. Monitor OASIS for updates.

automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.

when adjusting the climate control temperature. This may be due to the SYNC software installed in the accessory protocol interface module (APIM). Engineering is currently developing a software update that is expected in January 2022. Once the software update is available, it will be made available to customers who have enabled SYNC 3 Automatic Updates with their vehicle connected to a Wi-Fi network. Repair appointments should be scheduled for customers in February 2022 who do not receive Automatic Updates. Monitor OASIS for updates.

the degrees do not appear in the SYNC screen. This may be due to the SYNC software installed in the accessory protocol interface module (APIM). Engineering is currently developing a software update that is expected in January 2022. Once the software update is available, contact the customer and schedule a follow-up appointment for repair in February 2022. Monitor OASIS for updates.

PowerBoost with a vehicle build date on or after 19-July-2021 and 2021 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost with a vehicle build date on or after 10-Feb-2021, the turbocharger bypass valve (9U465) and adapter (9V456) must also be replaced. For turbocharger bypass valve and adapter replacement procedures, refer to the Workshop Manual (WSM), Section 303-14.

This feature automatically adjusts airflow in the cabin to prevent the windshield from fogging up and may be perceived by customers as irregular climate control functionality. To reduce fogging, the EWAFS functions include: the air condition (A/C) button may turn on and off automatically, recirculated air may turn off automatically in all air modes except MAX A/C, recirculated air may also turn on and off automatically in various airflow modes in order to improve heating or cooling efficiency, and in auto climate control, high humidity conditions may automatically engage A/C compressor, increase blower motor speed and/or direct more air to windshield. Continue to monitor the Workshop Manual (WSM) for EWAFS updates.

Expedition and Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04F0 and/or P144C stored in the powertrain control module (PCM). This may be due to loose or partially connected evaporative emissions (EVAP) vapor lines.

phone call by the person that is not in the vehicle. Using Apple CarPlay and Android Auto instead of Bluetooth can help alleviate the concern. Also turning on, then off, the privacy setting in the SYNC touchscreen can temporarily alleviate the concern. Engineering is currently investigating this concern and will be releasing a service fix in early July 2021. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. Monitor OASIS for updates.

to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

There may also be an illuminated malfunction indicator lamp (MIL) with any of the following diagnostic trouble codes (DTC) codes: P0201, P0202, P0203, P0204, P0205 or P0206. Follow the appropriate Pinpoint Tests in the Powertrain Control/Emissions Diagnosis Manual (PC/ED) for the DTCs received. If PC/ED diagnostics lead to replacement of a fuel injector, inspect the injector harness connections for possible spread terminals. Injector harnesses are available for service.

Some of the vehicles listed in the Model statement above may exhibit an instrument panel upper section speaker grille that is lifted, warped, or not seated flush with the instrument panel. This may be due to upper section speaker grille clips that are not seating.

that is lifted, warped, or not seated flush with the instrument panel. This may be due to upper section speaker grille clips that are not seating.

diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.

The customer may indicate that this concern is more noticeable after a car wash or rainfall. To correct the condition, follow the Service Procedure to identify the leak path.

entertainment system may experience the audio is not synchronized with the video display when using the vehicle speakers. To correct this condition, contact the VOXX Customer Service Department at 1-866-869-7888. For claiming, refer to the Warranty and Policy manual for Ford Licensed Accessories.

are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns including but not limited to: Sirius audio not functioning properly after a key cycle with active subscription Presets not responding or indicating properly Intermittent audio echo/robotic voice heard during a Bluetooth phone call Wi-Fi connection message pop-up every key cycle Frozen unresponsive touchscreen Solid blue screen when moving forward at speeds above 16 km/h (10 mph) (2019 vehicles only) Rear parking aid camera remains on the screen at speeds below 16 km/h (10 mph) (2019 vehicles only) Inoperative infotainment applications Poor/no AppLink function Apple CarPlay not launching on connection or a black screen when connected Voice prompts that skip or have short pauses while directions are being provided

intended to be installed with the heavy duty trailer tow package. As a result, the Slow Climb drive mode and the Neutral Tow setting will not be available on the Instrument Panel Cluster (IPC) message center display. This will prohibit the vehicle from being flat-towed and may cause poor drivability in extreme off-road conditions.

Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

have intermittent Phone-as-a-key connectivity, missing Phone-as-a-key button in the App, receiving Pairing Failed, Key Download Error or Connection Trouble message during Phone-as-a-key setup, Bluetooth Disconnected, Unable To Start, Backup Code Needed And/or Key Not Detected. Prior to performing any RFA diagnostics, verify the customer's phone app is at the latest version, the phone app is authorized to the vehicle and Location Service is enabled in customer's phone to allow for proper Phone-as-a-key operation. If a Phone-as-a-key concern remains, continue with normal RFA diagnosis. Refer to Workshop Manual (WSM), Section 419-01. Utilize the FordPass Guides or Lincoln Way Concierge teams as needed to understand Phone-as-a-key operation.

may experience various system concerns. Rear seat entertainment systems are not on a controller area network (CAN) and are not supported by the Ford Diagnostic and Repair System (FDRS). Certain system concerns may be resolved through software updates which will automatically download once each individual monitor is connected to Wi-Fi. Diagnostic support for rear seat entertainment systems is provided by VOXX electronics. If necessary, contact the VOXX Customer Service Department at 1-866-869-7888. If possible, record the device serial number by selecting the gear/Setup icon > Settings > Device and Software > About. If the unit will not power up, the serial number is on a label on the back of the monitor. It is helpful to know the date the issue occurred, how long the monitors were on prior to the issue, what app/input/media was being used, and if the system software was recently updated prior to the concern starting. For claiming, refer to the Warranty and Policy manual for

introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. When referred to a specific clutch (A-F) test by a pinpoint test in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing, the Clutch Assembly tests have been updated with a hyperlink to the new Transmission Line Pressure Test - Pressure Vacuum Transducer (PVT) Is Available procedure in WSM, Section 307-01 > General Procedures. This procedure provides instructions to perform the FDRS Transmission Clutch Circuit Leak Test when applicable. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification

Assembly Reimbursement

r/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.

engagement Delayed engagement Harsh shift Delayed shift Illuminated MIL with DTCs P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the PCM or TCM"

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

(7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

customer is using a Magsafe iPhone (iPhone 12 or 13): slow charging, inoperative, notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen display is not showing. This may be due to a compatibility issue between the customer's phone and the wireless accessory charging module (WACM) that may make it difficult for Ford and Lincoln vehicles to wirelessly charge these specific phones. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using a Magsafe iPhone such as an iPhone 12 or 13, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

charging, a notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen is not showing. This may be due to the customer's phone if they are using an iPhone 12. Vehicles equipped with a wireless charging pad are designed to charge best with phones that follow the Qi standard. The iPhone 12 hardware currently does not follow the Qi standard for wireless charging. This may make it difficult for Ford and Lincoln vehicles to wirelessly charge this specific phone. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using an iPhone 12, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.

after removing the transport protective covering on the vehicle. To correct this condition, polish the affected areas using a microfiber fabric, foam pad (3M-02648 model R-0297), clear coat polisher (3M-51056) and a power tool buffer (3M-28333). Do not attempt to replace the headlamps/taillamps before applying the polishing procedure.

lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901

This may be due to the adhesive separating from the headliner substrate.

This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.

This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.

opening panel may exhibit a binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. This may be due to the glass panel brackets cracking and/or breaking apart. The glass panel brackets are serviceable separately from the frame assembly and require the roof opening panel glass to be moved to the vent position. To correct the condition, follow the Service Procedure to replace the roof opening panel glass brackets

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Some 2018-2024 Navigator and Expedition vehicles may exhibit a concern where the second row seat back does not fold down or recline when the recline handle is pulled upward or the second row single seat easy entry seat fold switch is pressed. This concern may occur with vehicles equipped with two or three second row seats. This may be due to a broken recliner release lever. To correct this concern, replace the recliner release lever.

or recline when the recline handle is pulled upward or the second row single seat easy entry seat fold switch is pressed. This concern may occur with vehicles equipped with two or three second row seats. This may be due to a broken recliner release lever. To correct this concern, replace the recliner release lever.

of the load floor compartment come detached. This may be due to the joint between the gap hiders and the bin. To correct the condition, follow the Service Procedure steps to replace the damaged gap hiders.

tilted position while using Easy Entry preventing rearward movement. To unlock the seat, tip the seat back fully forward and slide the seat fully forward to its end of track travel. This will allow the seat to then be free to move rearward. This operation is characteristic to the Easy Entry feature of the second row seats. Do not force the seat rearward while in the locked position as it can result in damage to the seat track. Refer to the vehicle's Owner's Manual for further details.

which can be felt while driving on a smooth road at speeds at or above 75 mph (120 km/h). Pinpoint Test G located in Workshop Manual (WSM), Section 204-04 has been developed to assist with diagnosis of this condition. When submitting a warranty claim, include all results from the Pinpoint Test.

direction on one or both sidewalls. Sidewall wavy/indentation appearance is a common cosmetic characteristic of radial tire construction and will not affect the performance of the tire.

available in a TSB, SSM, or GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information

To correct the condition, follow the Service Procedure steps to install an isolator onto the front cross tube on both front seat tracks.

and BlueCruise - BlueCruise Maps Expiration. In some of the affected vehicles, the Connected Blue Zone Maps will expire on March 14, 2022. When the maps expire the BlueCruise with hands-free highway driving feature will no long be available. Unsold vehicles that are in transport mode or on dealer lots are unable to receive an over the air update containing the updated maps.

Some 2017-2020 Continental, 2018-2022 Navigator vehicles may experience seat pan looseness, lateral movement, and/or clunk/thump noise on turns. To correct the condition, follow the Service Procedure steps to install an isolator onto the front cross tube on both front seat tracks.

Workshop Manual (WSM) diagnostic procedures have been updated to more accurately diagnose A/C performance concerns. Refer to the updated Diagnosis and Testing, and General Procedure in the WSM, Section 412-00 Climate Control System for diagnostic procedures