2018 Lincoln MKX TSBs

Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.

battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

trailer lights flicker with vehicle turned off when a trailer is connected to the vehicle. This may be due to the software in the trailer module (TRM). To correct the condition, reprogram the TRM with the latest software of the appropriate Ford diagnostic scan tool. Use causal part 19H332 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.

symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

reprogramming or programmable module installation (PMI) process. This may be due to the software in the RGTM. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part number 14B291 and Section 10 of the Service Labor Time Standards (SLTS) Manual.

Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.

an SSM or TSB is published for a software update. This may be due to the module already being at the latest software level. A later software level may have been programmed at the assembly plant, during a previous dealer visit or by an over the air (OTA) update for vehicles that have automatic updates enabled in the SYNC system settings. To review a vehicle's OTA update history, visit the Connected Vehicle > OTA Dashboard tab in OASIS. Information about the OTA Dashboard can be found on FMCDealer.com when performing a search on OTA History Job Aid.

driver door does not unlock/open when pressing the door activation switch, or the door activation switch not lighting up. This may be due to a software configuration in the body control module (BCM). To correct the condition, reprogram the BCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 15604 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

replacing the driver airbag using certain part numbers only and/or if replacing the restraints control module (RCM). In addition, some vehicles may exhibit diagnostic trouble code (DTC) U2300 stored in the RCM if the correct programming procedure was not followed.

18-Jan-2020 may exhibit a mirror click and/or ratcheting noise when using memory functions or easy entry/exit function. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

trailer lights flicker with vehicle turned off when a trailer is connected to the vehicle. This may be due to the software in the trailer module (TRM). To correct the condition, reprogram the TRM with the latest software of the appropriate Ford diagnostic scan tool. Use causal part 19H332 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.

Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.

This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".

Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.

App Concerns Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

2016-2018 MKX, 2019-2020 Nautilus, 2020 Aviator/Corsair and 2013-2020 MKZ vehicles equipped with multi-contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

in the Ford Pass/Lincoln Way mobile app advising, Your vehicles software is being updated. Vehicle controls will be unavailable for about 10 minutes while this update takes place. This may be due to the TCU still in factory mode. Using the appropriate Ford diagnostic scan tool, check the TCU_AUTHSTATE PID status showing Factory Mode. To correct this condition, perform programmable module installation (PMI) on the telematics control unit (TCU). Once PMI is completed, ensure the TCU_AUTHSTATE PID in service tool no longer displays Factory Mode. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM) section 415-00. For claiming, use causal part 14G229.

Nautilus, and 2013-2019 MKZ vehicles equipped with Multi-Contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.

When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section

Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.

inoperative heated steering wheel. For vehicles equipped with adaptive steering, the steering effort control module (SECM) controls the heated steering wheel feature and is internal to the vehicle's steering wheel. For vehicles not equipped with adaptive steering, the heated steering wheel module (HSWM) controls the heated steering wheel feature and is separate from the steering wheel. Using the OASIS Tab drop down > HVBoM > Features button or an appropriate Ford diagnostic scan tool, you can determine if the vehicle is equipped with Adaptive Steering. Refer to the Workshop Manual (WSM), Section 211-05.

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition, remove the TCU fuse for 5 minutes prior to programing. Delete all previous session files for the vehicle and do not install the TCU fuse until a new IDS session has been started. Once the new session has been started and the fuse reinstalled, the TCU can be programmed. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

2017-2018 Escape vehicles with Sony audio systems may exhibit an inoperative speed compensated volume feature. This may be due to the calibration in the audio control module (ACM). To correct the concern, reprogram the ACM to the latest calibration using the appropriate Ford scan tool release 110.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

steering wheel and/or heated seats grayed out in the cluster. To correct this concern, reconfigure the front controls interface module (FCIM) using As-Built Programming. Make sure you are connected to the internet when entering module programming to obtain the latest data. If the concern is still present, refer to Workshop Manual (WSM), Section 501-10A for the directed self-test for the FCIM. For claiming, use causal part 18842 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.

Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition, remove the TCU fuse for 5 minutes then reinstall. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

to disable the intrusion sensor through the cluster alarm menu under vehicle settings. This may be due to a missing instrument panel cluster (IPC) menu selection to allow the intrusion sensor to be disabled. Reconfigure the IPC module using As-Built Programming. Make sure you are connected to the internet when entering module programming to obtain the latest data. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Revised Cargo covers are available to address this issue. Use the vehicle identification number (VIN) to select the interior trim color of the vehicles; FA1Z- 5845440-AG(Ebony), FA1Z- 5845440-AH (Coffee), FA1Z-5845440-BG (Ebony Black Label), FA1Z- 5845440-BH (Espresso Black Label), FA1Z-5845400-BJ (Rouge Noir).

only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs.

vehicles equipped with a 2.7L EcoBoost or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

Fusion/MKZ vehicles built on or before 15-Aug-2019 equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. To correct the condition, follow the Service Procedure steps to replace the oil pan with a new oil pan equipped with a press in place gasket.

Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.

to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.

Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.

enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.

supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.

2.7L EcoBoost engines may exhibit an illuminated malfunction indicator lamp (MIL) and/or Engine Coolant Over Temperature warning with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0128, P0217, P0330, P1026, P1299, and/or P130D. This may be due to the engine coolant temperature (ECT) sensor or knock sensor wiring harness. To correct the condition, replace the 12A648 ECT sensor and 12A699 knock sensor. Do not disconnect the ECT sensor from the knock sensor harness in case parts are called back for analysis. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Fusion/MKZ vehicles built on or before 15-Aug-2019 equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. To correct the condition, follow the Service Procedure steps to replace the oil pan with a new oil pan equipped with a press in place gasket.

exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0766 stored in the powertrain control module (PCM) and/or intermittent no reverse engagement concerns. This may be due to contamination in the main control valve body separator plate orifice. To correct the condition, follow the Service Procedure steps to clean the contamination from the main control plate.

To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal.To correct the condition, follow the Service Procedure.

Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

vehicles equipped with a 2.7L or 3.0L EcoBoostengine it is critical to inspect the oil filter housing center stem to verify is not separated or damaged. If the center stem is damaged or separated from the housing this will result in oil flow through the reservoir drain port causing low engine oil pressure and internal engine damage. If the filter housing stem is damaged or separated, the oil filter housing must be replaced. If the center stem is not damaged or separated, the O-ring seals on the stem and housing must be replaced each time the filter is serviced.

Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

U3000:49 diagnostic trouble code (DTC) setting in the Steering Effort Control Module (SECM) with no other DTCs present. To eliminate the DTC, perform the IDS SASM module reset routine. The IDS reset routine is available under Toolbox > Chassis > Steering > Adaptive Front Steering > SASM Module Reset. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. For claiming, use causal part 3600 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

Replace the oil pan following the procedure in Workshop Manual (WSM) Section, 303-01. After removing the oil pan it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV and clean the engine sealing surface using only Motorcraft Metal Brake Parts Cleaner, then wipe with Motorcraft Metal Surface Prep Wipes and allow to air dry. Refer to WSM, Section 303-00 > RTV Sealing Surface Cleaning and Preparation. If possible, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Skipping or improperly completing steps may result in repeat oil pan leaks.

DTC P013C in the powertrain control module (PCM). This may be due to an exhaust system leak. Exhaust leak inspection should be conducted before performing Powertrain Control/Emissions Diagnostics PC/ED Manual diagnostic routines. Inspect for carbon soot/moisture witness marks at all exhaust connections and catalyst monitor sensor (CMS) threads. Refer to Workshop Manual (WSM), Section 303-14C. Inspect CMS crush washer to confirm sensor is fully seated in the exhaust pipe. Apply soapy water to exhaust connections including CMS threads, while exhaust flow is restricted at the tailpipe and exhaust system is pressurized at 5 PSI (do not exceed 5 PSI), will increase ability to identify and confirm leaks.

MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.

MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.

Replace the oil pan by performing the published Workshop Manual (WSM) service procedures. After removing the oil pan, it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV, clean the engine sealing surface with only Motorcraft Metal Brake Parts Cleaner then wipe with Motorcraft Metal Surface Prep Wipes, and allow to air dry as directed in WSM, Section 303-00, RTV Sealing Surface Cleaning and Preparation. If possible, after the new oil pan is installed, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Ford is investigating this concern. Monitor OASIS for future updates.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

experience a malfunction indicator lamp (MIL) and/or wrench lamp with Diagnostic Trouble Codes (DTCs): P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. If an issue with the wiring is found use causal part 12A699.

exhibit an inoperative speed compensation volume feature. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to:  Display operation concerns  Navigation inoperative  Voice recognition concerns  Phone connection issues  Dropped phone connections  Applink related performance  Travel Link not present or showing incorrect traffic  Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.

are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.

Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14H092 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.

every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.

not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.

SYNC/SYNC3 with automatic system updates do not support connecting SYNC to the vehicles internal 4G WI-FI Hotspot if equipped. The SYNC automatic update feature must be connected to an external Wi-Fi source to function properly. No repairs should be made in attempt to correct this concern.

original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.

may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before performing any diagnosis or repairs for this condition. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device.

may exhibit a concern where USB Audio playback and App Link applications will not function properly. This may also include, under certain conditions, no Bluetooth Streaming. Apple is aware of the issue and is working on a resolution with a future iOS release. No repairs should be performed at this time. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device. Monitor OASIS for updates. Customers can also check Apple Support or connect to iTunes for the latest available iOS release for their phone.

Some 2015-2019 Edge, 2016-2018 MKX, and 2019 Nautilus vehicles built on or before 05-Jun-2019 may exhibit a rattle or flutter noise from the underbody of the vehicle while moving. This may be due to the movement of loose underbody shield fasteners which are attached to the underbody shields. To correct the condition, follow the Service Procedure to remove the assembly aid fasteners.

This may be due to an incorrect adjustment of the rubber bump stops. To correct this condition, make sure the rubber bump stops are in contact with the inner hood sheet metal. Using a piece of paper between the hood and the rubber hood stop, make sure the paper fits snug with hood closed. For claiming, use causal part number 16612 and applicable labor times from Section 12 of the Service Labor Times Standard (SLTS) Manual.

track or frame for various conditions. When replacing the roof opening panel, the replacement component may have less magnet plates. In order to prevent any noise vibration or harshness (NVH) concerns, the magnets on the headliner around the roof opening panel that line up with the removed magnet plates should be discarded.

This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

This may be due to the spacing between the exterior mirror base and the mirror cover. To correct the condition, follow the Service Procedure steps to add foam to the back of the mirror cover for the affected side(s).

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.

EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.

remains on with the liftgate fully closed. The customer may also complain of an intermittent alarm activation. This may be due to a broken switch inside of the liftgate latch. Replace the liftgate latch. Refer to Workshop Manual (WSM), Section 501-14. For claiming, use causal part 7443150 with the appropriate body code for your vehicle and applicable labor operations in Section 12 of the Service Labor Times Standards (SLTS) Manual.

equipped with a power liftgate and the hands-free liftgate activation feature may exhibit the liftgate opening or closing when a rear door is slammed shut, or the rear fascia is contacted such as kneeling or resting a foot on the fascia while the key is present. Follow the Service Procedure steps to correct the condition.

exhibit an intermittent bounce back after closing has been commanded. Follow the Service Procedure steps to correct this condition.

not control tailpipe emissions effectively over time.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

not control tailpipe emissions effectively over time.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

slosh noise primarily when the fuel tank is over 3/4 full and when driving at low speeds. This may be due to the fuel moving around in the fuel tank. Follow the Service Procedure steps to correct the condition.

P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.

As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

Flexible Hose Replacement

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

Front Brake Flexible Hose Replacement REASON FOR THIS SUPPLEMENT Parts Requirements / Ordering Information: Part numbers for Edge and MKX vehicles have been added. Edge and MKX model year updated from 2018 to 2019, build dates remain the same.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

Front Brake Flexible Hose Replacement Submitting Owner Letters

Front Brake Flexible Hose Replacement In some of the affected vehicles, brake fluid may leak from one or both front brake flexible hoses. If the brake fluid reservoir is depleted below a predetermined level, the brake fluid warning indicator light will illuminate. The driver may experience an increase in pedal travel together with a reduction in the rate of deceleration over time.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.

Replacement If Required After Dealer Evaluation

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.

system is in auto or recirculation mode. Customers may indicate the odor smells like sulfur or exhaust odors are entering the vehicle cabin. This concern may be more pronounced after hard acceleration, driving in hilly conditions and/or towing a trailer. Whether and to what extent any occupant of these vehicles experiences the exhaust odor will be affected by driving habits, weather, and individual sensitivities. Follow the Service Procedure steps to correct the condition.