2008 Lincoln Mark LT TSBs

The customer communication requested return of unsold inventory to inspect for the port size being too large. If the port size is too large it will not fit the mating component which would prevent installation, and would therefore have no impact on the end user besides time to complete installation.

released to assist with proper repair of the 4R75E transmission in 2008 Mark LT, 2008-2010 F-150, 2008-2010 / 2013-2014 E-Series, 2008-2011 Crown Victoria, Grand Marquis and Town Car vehicles that exhibit a grinding, whine-type noise, vibration and/or gear slippage while driving, or a loss of reverse resulting from a planetary gear assembly failure.

GRINDING, GEAR SLIPPAGE, WHINE TYPE NOISE, VIBRATION, WHILE DRIVING OR LOSS OF REVERSE. *PE

CLUTCH FAILURE AND DIAGNOSTIC TROUBLE CODE (DTC) P0733 AND/OR P0734. MODEL 2008-2013 MARK LT, F-150, CROWN VICTORIA, GRAND MARQUIS, TOWN CAR, E SERIES. *PE

MODELS 2008-2013 F-150, EXPEDITION, NAVIGATOR, MARK LT. *PE

Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 (non-Raptor) vehicles equipped with 4WD may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure to remove and cap the vacuum supply line or to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.

The programming may fail or vehicle symptoms such as inoperative door locks, dome lamps, door ajar indicators or auto lamps may occur after successful programing. To ensure the VSM is configured correctly, use the Integrated Diagnostic System (IDS) scan tool and select the blue ball and socket icon in the upper left corner. Select the utility knife in the bottom left corner. Select Update/Special Function and enter 53061 in the blue box then press the tick mark. The screen will go back to the system utilities page. Navigate to the toolbox tab and run the Programmable Module Installation (PMI) on the VSM. The procedure will prompt you to manually enter the as-built into the VSM. Obtain the as-built data from PTS > OASIS > As-Built.

The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

ALL VEHICLES EQUIPPED WITH 6.5 CARGO BOX ARE EQUIPPED WITH THREADED ATTACHMENT HOLES LOCATED ON THE BOX INNER SHEET METAL PANELS. THESE HOLES ARE DESIGNED TO ACCEPT FASTENERS THAT SECURE AN OPTIONAL CARGO MANAGEMENT SYSTEM SIDE RAILS TO THE BED. *PE

*NJ

symptoms that may include upper end engine noise, rough running, misfire and/or engine damage. If diagnosis leads to only camshaft/camshaft roller follower(s) requiring replacement, replace all of the camshaft roller followers on both banks/cylinder heads with part number 3L3Z-6564-A, not just the faulty roller follower(s). When replacing the camshaft roller followers, refer to Workshop Manual (WSM), Section 303-01.

Replace all black spark plug boots from the original engine with the 'brown' spark plug boots, as provided. The updated 'brown' spark plug boots are longer than the black boots to accommodate a running change in the spark plug length. The ignition coil bodies and spring/resistor are transferable and only the rubber boots require replacement. Failure to install the spark plug boots provided with the replacement engine could lead to drivability concerns.

2004-2013 F-150, F-250, F-350, EXPEDITION, MARK LT, NAVIGATOR. *PE

IDLE RPM FLUCTUATION AND EXHIBIT DIAGNOSTIC TROUBLE CODES (DTCS) P0505, P0506, P2111 AND P2112. *PE

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

*NJ

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

THE 2004-07 WSM MANUAL PROVIDES TWO SEPARATE PROCEDURES FOR MOON ROOF HEIGHT A HORIZONTAL ADJUSTMENTS. HEIGHT AND HORIZONTAL PROCEDURES NEED TO DONE TOGETHER. MANUAL PROCEDURES IS IN THE PROCESS OF BEING UPDATED. *PE

FRONT HUBS WHEN OPERATING IN TWO-WHEEL DRIVE (2WD) MODE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

*NJ

*KB