2026 Lincoln Corsair TSBs

> Front Seats > Diagnosis and Testing lead to the replacement of the front seat cushion extension adjuster, a lower-level part is now available (14C720). It is not necessary to replace the front seat cushion extension adjuster if only the front seat cushion extension motor assembly is damaged. For Corsair, use service part LJ7Z-14C720-A. For Aviator, use service part R2TZ-14C720-A. For 2025-2026 Navigator (both sides) and 2018-2024 Navigator driver side, use service part NL7Z-14C720-A. For 2018-2024 Navigator passenger side, use service part NL7Z-14C720-B.

in the WSM, Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, and/or D>R) should be noted in the warranty claim. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.

transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation. For claim

transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation.

with diagnostic trouble code (DTC) P04CA stored in the powertrain control module (PCM). This may be due to an open circuit on circuit SBB05 and/or a damaged splice S133. Before performing the pinpoint test for P04CA in Workshop Manual (WSM), Section 310-00, inspect circuit SBB05 and splice S133 for damage such as an open circuit. Repair as necessary. Refer to Wiring Diagram, Cell 005. If no damage is found, refer to WSM, Section 310-00 for normal diagnostics. For claiming use causal 14290 and labor operations 12650D, 12650D45, and 12650D45WR.

One time use parts for Corsair and Bronco Sport were also added to the parts list. Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.

One time use parts for Corsair and Bronco Sport were also added to the parts list. Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.

looseness/sagging or binding/inoperative. This may be due to a broken or missing sunshield fabric retainer/clip. A revised sunshield clip (5452118) is available to address this condition. It is not necessary to replace the entire sunshield assembly if the clip(s) are broken or missing. Refer to Workshop Manual (WSM), Section 501-17 Roof Opening Panel for inspection and replacement of the roof opening panel shield clip.

Aviator Vehicles Windshield Replacement

system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration

Maverick/Bronco Sport vehicles built on or before 20-Jan-2026 2024-2026 Nautilus vehicles built on or before 02-Dec-2025 2023-2026 Escape/Corsair may exhibit reduced steering assist and a "Power Steering Assist Fault" message displayed in the instrument panel cluster (IPC) with the diagnostic trouble code (DTC) U2016:47 only, and no other steering DTCs stored in the power steering control module (PSCM). To correct this condition, reprogram the PSCM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 3C529 and labor operations 3504E and PSCM. If a software update is not available for the PSCM, the PSCM is already at the latest software level. Refer to Workshop Manual (WSM), Section 211-02 for normal diagnostics. If the vehicle does not exhibit any observable symptoms described above and the DTC is only present in continuous memory, this DTC should be ignored. No further service action

Some of the vehicles listed in the Model statement above may exhibit a "Pre-Collision Assist Not Available" message in the IPC and at least one of the following conditions:  Various driver assistance feature warning messages in the instrument panel cluster (IPC): - "Blind Spot System Fault" - "Cross-Traffic System Fault" - "Front Camera Fault - Service Required"  Various data or lost communication diagnostic trouble codes (DTCs) stored in various modules  Ford Diagnosis and Repair System (FDRS) scan tool cannot establish connectivity with the image processing module A (IPMA) during a self-test. This may be due to the software installed in the IPMA. *** MODEL SECTION ****  2023-2026 Escape equipped with minor feature code: DBCAB or DBCAA  2023-2026 Corsair equipped with minor feature code: DBCBC

Reason for update: Add 2022-2025 Transit vehicles. Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display screen after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.

screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.