2024 Lincoln Corsair TSBs

This may be due to a concern with the front courtesy lamp light module.

system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration

Maverick/Bronco Sport vehicles built on or before 20-Jan-2026 2024-2026 Nautilus vehicles built on or before 02-Dec-2025 2023-2026 Escape/Corsair may exhibit reduced steering assist and a "Power Steering Assist Fault" message displayed in the instrument panel cluster (IPC) with the diagnostic trouble code (DTC) U2016:47 only, and no other steering DTCs stored in the power steering control module (PSCM). To correct this condition, reprogram the PSCM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 3C529 and labor operations 3504E and PSCM. If a software update is not available for the PSCM, the PSCM is already at the latest software level. Refer to Workshop Manual (WSM), Section 211-02 for normal diagnostics. If the vehicle does not exhibit any observable symptoms described above and the DTC is only present in continuous memory, this DTC should be ignored. No further service action

Batteries Battery Energy Control Module (BECM) Software Update

Reason for update: To add a Step to reprogram the all-wheel drive (AWD) module for Bronco Sport vehicles. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions:  Shudder chatter condition, most noticeable at low speeds turning  No relevant diagnostic trouble codes (DTCs) present This may be due to internal rear drive unit (RDU) fluid contamination.

stored in the accessory protocol interface module (APIM). This may be due to the software in the front audio control module (ACM). To correct the condition, reprogram the ACM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 18C869 and labor operations 12651D and 12651D4.

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

stored in the accessory protocol interface module (APIM). This may be due to the software in the front audio control module (ACM). To correct the condition, reprogram the ACM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 18806 and labor operations 12651D and 12651D4.

statement above may exhibit various electrical symptoms, and/or a no crank/no start condition related to a 12V battery drain condition. This may be due to the software level of the affected module(s).

of AP (Actual Programming) Time. Some of the vehicles listed in the Model statement above may exhibit various electrical symptoms, and/or a no crank/no start condition related to a 12V battery drain condition. This may be due to the software level of the affected module(s).

of the fan speed icon when changing the fan speed on the center display screen. This may be due to the software level installed in the accessory protocol interface module (APIM).

Some of the vehicles listed in the Model statement above may exhibit a "Pre-Collision Assist Not Available" message in the IPC and at least one of the following conditions:  Various driver assistance feature warning messages in the instrument panel cluster (IPC): - "Blind Spot System Fault" - "Cross-Traffic System Fault" - "Front Camera Fault - Service Required"  Various data or lost communication diagnostic trouble codes (DTCs) stored in various modules  Ford Diagnosis and Repair System (FDRS) scan tool cannot establish connectivity with the image processing module A (IPMA) during a self-test. This may be due to the software installed in the IPMA. *** MODEL SECTION ****  2023-2026 Escape equipped with minor feature code: DBCAB or DBCAA  2023-2026 Corsair equipped with minor feature code: DBCBC

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Inoperative BlueCruise and lane centering * DTC U2018:51 stored in the camera module - rear (CMR) * DTC U0565:86 stored in the image processing module A (IPMA) * DTC U3000:49 is not stored in the CMR This may be due to the software in the CMR.

Some of the vehicles listed in the Model statement above may exhibit a 12V battery drain condition. This may be due to the software level of the affected module(s).

lamp (MIL) with diagnostic trouble code (DTC) P27B2 stored in the secondary on-board diagnostic control module C (SOBDMC). This may be due to the software in the SOBDMC.

control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.

with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software level of the PCM.

caused the Image Processing Module A being offline

driver assistance feature warning messages in the instrument panel cluster (IPC): - "Blind Spot System Fault" - "Cross-Traffic System Fault" - "Front Camera Fault - Service Required" - "Pre-collision Assist Not Available"  Various data or lost communication diagnostic trouble codes (DTCs) stored in various modules  Ford Diagnosis and Repair System (FDRS) scan tool can not establish connectivity with the image processing module A (IPMA) during a self test. This may be due to the software installed in the IPMA. *** MODEL SECTION ****  2023-2025 Escape equipped with minor feature code: DBCAB  2023-2025 Corsair equipped with minor feature code DBCBC

and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC. Additionally, some modules may store invalid data/lost communication related DTCs. The image processing module A (IPMA) should not store these DTCs. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This condition may be due to the software in the IPMA, causing it to not communicate on the network. To restore communication and functionality, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) scan tool. Once IPMA communication has been restored, download and run the "IPMA - Image Processing Module (IPMA) Alignment"

with diagnostic trouble code (DTC) P144F stored in the powertrain control module (PCM). This may be due a concern with the fuel pump and sender unit.

2024-2025 Nautilus vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450:00 stored in the powertrain control module (PCM). This may be due to an evaporative emission system concern or may also be caused by the customer overfilling the fuel tank. If this condition occurs, perform normal diagnosis per Workshop Manual (WSM) Section, 303-13 and repair as necessary. Inform the customer that the condition may have been caused by overfilling of the fuel tank and to not top-off the fuel tank when the fuel pump nozzle automatically shuts off for the first time. Refer the customer to the Fuel and Refueling section of their Owner Manual for additional information.

cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.

lamp (MIL) with diagnostic trouble code (DTC) P144B stored in the powertrain control module (PCM) without driving performance concerns. This may be due to the PCM software.

Service Procedures from M-time to AP-time. Some of the vehicles listed in the Model statement above may exhibit a 12V battery drain condition. This may be due to the software level of the affected module(s).

trouble code (CMDTC) U2016:47 stored in the power steering control module (PSCM) after a self test is performed with Ford Diagnosis and Repair System (FDRS) scan tool.

system performance/stability/intermittent system reboot * Intermittent wireless CarPlay or Android Auto function * Phone related concerns with intermittent no audio or static * Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto * Alexa function consistency and stability * Charge Assist/Public Charging app inoperative (e-Transit only) This may be due to a concern with the software in the accessory protocol interface module (APIM).

trouble code (CMDTC) U2016:47 stored in the power steering control module (PSCM) after a self test is performed with Ford Diagnosis and Repair System (FDRS) scan tool.

accessory protocol interface module (APIM) software updates have been performed.

Please Contact Your Dealership." message in the instrument panel cluster (IPC) when the vehicle is in reverse and DTC B1578:89 stored in the image processing module A (IPMA) may be present on some of the following Ford and Lincoln vehicles: * 2024 F-150/F-Super Duty built on or before 08-Apr-2024 * 2024 Expedition/Navigator built on or before 07-Mar-2024 * 2024 Corsair built on or before 30-May-2024 * 2021-2024 Mustang Mach-E built on or before 20-May-2024

cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.

may result in an inaccurate fuel level measurement

-Minor quality fixes in Enhanced Central Gateway module (ECG) Software, not affecting vehicle operation. - Addresses potential vehicle no start after OTA update.

Some 2021-2024 Mustang Mach-E/F-150, 2022-2024 F-150 Lightning/Expedition/Navigator, 2023-2024 Corsair vehicles may exhibit an inoperative BlueCruise and lane centering with DTCs U2018:51 stored in the camera module - rear (CMR) and U0565:86 stored in the image processing module A (IPMA) without DTC U3000:49 stored in the CMR. This may be due to the software level of the CMR. To correct the condition, follow the Service Procedure to reprogram the CMR module using the latest software level of the Ford Diagnosis and Repair System (FDRS).

message center with loss of AWD function for the remainder of the active key cycle. DTCs C0095, C05D9:74, P060A, P060B, P060C, and/or P1674 may be stored in the AWD module. This condition may be due to the software in the AWD module.

instrument panel cluster (IPC) and an illuminated malfunction indicator (MIL) lamp with diagnostic trouble code (DTC) P1346:13 stored in the IPC and/or DTC P2068 stored in the powertrain control module (PCM) when the fuel level is not low, pinpoint test C in Workshop Manual, Section 310-01 has been updated to better identify root cause of a "Fuel Level Low" symptom.

scenarios where ECG algorithm drains the battery when vehicle is parked and only during key off events. - 23 MY HEV vehicles reduces battery drain related to Air Conditioning Control Module (ACCM) staying awake. - ECG minor updates not affecting customer experience.

accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.

condition when the ignition is turned off. This may be due to the vehicle dynamics control module (VDM) that keeps the controller area network (CAN) bus active. To correct this condition, follow the Service Procedure to reprogram the VDM.

failure with a message displayed in the Ford Diagnosis and Repair System (FDRS) scan tool indicating Procedure Unsuccessful-Flash Software Failed To Flash. This may be due to the ACM programming routine. To correct this condition, download and click the refresh icon located next to the run icon to update the ACM - Programmable Module Installation (PMI) app. For claiming, use causal part 18C869 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.

an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

> Front Seats > Diagnosis and Testing lead to the replacement of the front seat cushion extension adjuster, a lower-level part is now available (14C720). It is not necessary to replace the front seat cushion extension adjuster if only the front seat cushion extension motor assembly is damaged. For Corsair, use service part LJ7Z-14C720-A. For Aviator, use service part R2TZ-14C720-A. For 2025-2026 Navigator (both sides) and 2018-2024 Navigator driver side, use service part NL7Z-14C720-A. For 2018-2024 Navigator passenger side, use service part NL7Z-14C720-B.

in the WSM, Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, and/or D>R) should be noted in the warranty claim. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.

Reason for update: update the service procedure to include the fuel tank isolation valve replacement, update the causal part number, and increase the labor time allowance to include the fuel tank isolation valve replacement. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software in the PCM and/or the fuel tank isolation valve.

Reason for update: update the service procedure to include the fuel tank isolation valve replacement, update the causal part number, and increase the labor time allowance to include the fuel tank isolation valve replacement. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software in the PCM and/or the fuel tank isolation valve.

2025 Model Year Maverick Vehicles Equipped with an Engine Block Heater System Block Heater Replacement

transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation. For claim

condition * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0301, P0302, P0303, and/or P0304 stored in the powertrain control module (PCM)

transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation.

with diagnostic trouble code (DTC) P04CA stored in the powertrain control module (PCM). This may be due to an open circuit on circuit SBB05 and/or a damaged splice S133. Before performing the pinpoint test for P04CA in Workshop Manual (WSM), Section 310-00, inspect circuit SBB05 and splice S133 for damage such as an open circuit. Repair as necessary. Refer to Wiring Diagram, Cell 005. If no damage is found, refer to WSM, Section 310-00 for normal diagnostics. For claiming use causal 14290 and labor operations 12650D, 12650D45, and 12650D45WR.

1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and/or may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the high-pressure fuel pump causing fuel to enter the crankcase and reduce fuel pressure in the direct injection fuel rail. Diagnose this condition using Pinpoint Test HP located in Workshop Manual (WSM), Section 303-04. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. Repair as necessary outside of this article. For claiming, if high-pressure fuel pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article.

Mustang, and Ranger Vehicles with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacemen

Equipped with an Engine Block Heater System Block Heater Element Installation

(OFF/AUTO/fan speed number) changes to a different language character or symbol. This may be due to the accessory protocol interface module (APIM) software. Replacement or reprogramming of the APIM will not resolve this condition. Inform customers that engineering is currently working on a solution for this condition and will be released via software updates delivered over-the-air (OTA) expected Q4 2025. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Schedule a service visit for customers who have disabled vehicle connectivity or who report that they did not receive the update by October 2025. Monitor Professional Technician System (PTS) for additional information.

message displayed in the instrument panel cluster (IPC) along with other various driver assistance feature warning messages and various invalid data/lost communication diagnostic trouble codes (DTCs) stored in various modules after Technical Service Bulletin (TSB) 25-2249 has been performed. The reoccurrence of these symptoms is related to a different root cause. This condition does not affect vehicle durability, and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in late October 2025. Replacement of the image processing module A (IPMA) will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.

with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacement

1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the fuel injection pump causing fuel to enter the crankcase and reduce fuel pressure in the high pressure fuel rail. Diagnose this condition using Pinpoint Test HP located in the Workshop Manual, Section 303-04A. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. For claiming, if fuel injection pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article. Note: Components damaged as a result of this failure mode

when shifting to neutral without pressing the brake pedal - Reduces potential no start events due to ABS after OTA update. -If the vehicle shuts off with Auto Vehicle Hold on, itll wake up with AVH on. -Addresses erroneous "Service Park Brake Limited Function" message at start up. - A Check Engine Light may appear after the update, causing no effect on the vehicle. This clears after a few drive cycles

2.0L EcoBoost engine, 2024-2025 Nautilus vehicles equipped with a 2.0L EcoBoost engine, 2024-2025 Mustang vehicles with a 2.3L EcoBoost engine, and 2025 Bronco/Explorer/Ranger vehicles equipped with a 2.3L EcoBoost engine may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). This may be due to the spark plugs and/or ignition coils. To correct the condition, refer to Workshop Manual (WSM), Section 303-07 for normal diagnostics.

Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.

neutral without pressing the brake pedal - Reduces potential no start events due to ABS after OTA update. -if the vehicle shuts off with Auto Vehicle Hold on, itll wake up with AVH on. -Addresses erroneous "Service Park Brake Limited Function" message at start up. - A Check Engine Light may appear after the update, causing no effect on the vehicle. This clears after a few drive cycles.

exhibit erratic shifting and/or a transmission fluid venting condition. If during the preliminary inspection the transmission fluid is found to be a foamy pink color, this may indicate possible cross contamination of engine coolant and transmission fluid due to an internally leaking transmission fluid cooler assembly.

a 2.3L EcoBoost engine, 2024-2025 Nautilus, and 2025 Explorer vehicles equipped with a 2.3L EcoBoost engine may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM).

a 2.3L EcoBoost engine, and 2024 Nautilus vehicles may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). If the codes are stored in the PCM, remove and inspect the condition of all the spark plugs. If all spark plugs are found to be free of damage, replacement of the spark plugs is not necessary. Refer to the Workshop Manual and perform normal diagnostics. If any spark plugs appear to be damaged, use a borescope to inspect the condition of the cylinder walls. If the cylinder walls are scored/scraped/damaged, replace the long block engine assembly (6006) to resolve this condition. If the cylinder walls are not scored/scraped/damaged, replace the damaged spark plug(s) and advise the customer that engineering is investigating this issue. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

condition where the flat tow mode cannot be activated. This condition does not affect vehicle durability under normal driving conditions and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle normally but should not attempt to flat tow the vehicle. Engineering is currently working on a software solution for this condition that is expected by the 4th quarter of 2024. Replacement/reprogramming of the IPC will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

a 2.3L EcoBoost engine, and 2024 Nautilus vehicles may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). If the codes are stored in the PCM, remove and inspect the condition of all the spark plugs. If any spark plugs appear to be damaged, use a borescope to inspect the condition of the cylinder walls. If the cylinder walls are scored/scraped/damaged, replace the long block engine assembly (6006) to resolve this condition. If the cylinder walls are not scored/scraped/damaged, replace the damaged spark plug(s) and advise the customer that engineering is investigating this issue. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.

Assembly Reimbursement

Some of the vehicles listed in the Model statement above may exhibit all of the following conditions:  Shudder chatter condition, most noticeable at low speeds turning  No diagnostic trouble codes DTCs present Note: Three (3) new Essential Special Service Tools (ESSTs) are required to service the internal clutch pack on vehicles equipped with a single active torque rear drive unit (RDU) only. These ESSTs are expected to ship to all dealers (US, Canada, Puerto Rico and Mexico) in September 2025. ESST packages were shipped to 100 selected dealers in the US and Canada in May 2025, based on RDU part sales activity. The RDU Internal Clutch Kit and Adhesive Sealant are currently under restricted ordering to ensure ample supply of parts are available to dealers with the ESSTs. All parts are expected to be available for open order by Q4 2025, when the ESSTs are planned to arrive at all dealers. Note: For dealers with the ESSTs and a vehicle in the service department that requires a repair using the new RDU Internal Clutch

r/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.

vehicles to avoid transmission damage. -Improved CarPlay experience"

neutral without pressing the brake pedal - Reduces potential no start events due to ABS after OTA update. -if the vehicle shuts off with Auto Vehicle Hold on, itll wake up with AVH on. -Addresses erroneous ""Service Park Brake Limited Function"" message at start up."

may exhibit a click or ting noise during acceleration from a stop, or in some cases during the end of a stop event.

may exhibit a click or ting noise during acceleration from a stop, or in some cases during the end of a stop event.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

noise during acceleration from a stop, or in some cases during the end of a stop event. This may be due to the front half shaft sticking to the wheel bearing surface. To correct this condition, perform the Service Procedure below to lubricate the halfshaft and wheel bearing hub assembly mating surface.

One time use parts for Corsair and Bronco Sport were also added to the parts list. Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.

Reason for update: add Bronco Sport and Escape vehicles and add labor operations to repair the rear right/left carpet area. Some of the vehicles listed in the Model statement above may exhibit a condition where the carpet is loose or torn near the front/rear scuff plate trim panel. This may be due to the carpet tearing at or near the retainer hole.

One time use parts for Corsair and Bronco Sport were also added to the parts list. Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.

looseness/sagging or binding/inoperative. This may be due to a broken or missing sunshield fabric retainer/clip. A revised sunshield clip (5452118) is available to address this condition. It is not necessary to replace the entire sunshield assembly if the clip(s) are broken or missing. Refer to Workshop Manual (WSM), Section 501-17 Roof Opening Panel for inspection and replacement of the roof opening panel shield clip.

Aviator Vehicles Windshield Replacement

This may be due to the carpet tearing at or near the retainer hole.

-Addresses Key Off Load alert issue related to BLEM Software. "

may experience the overhead console sunglass bin cannot be locked in a closed position.

where the door(s) do not open using the exterior door handle(s). This may be due to an enabled door reinforcement inertia lock within the exterior door handle. This condition occurs when the doors are closed or opened with excessive force. To correct this condition, follow the door reinforcement inertia lock rest procedure that has been added to Section 501-14 of the Workshop Manual under General Procedures. For claiming, use causal part 78219A64.

may exhibit all of the following conditions:  Shudder chatter condition, most noticeable at low speeds turning  No diagnostic trouble codes DTCs present This may be due to rear drive unit internal (RDU) fluid contamination.

above may exhibit all of the following conditions:  Shudder chatter condition, most noticeable at low speeds turning  No diagnostic trouble codes DTCs present This may be due to rear drive unit internal (RDU) fluid contamination.

AP-time.

Quality Improvements include: - Improved OTA deployment

date, and include a parts list with the Rotunda part number of the flock tape. Some of the vehicles listed in the Model statement above may exhibit a squeak or rattle noise from the center display screen. This may be due to improperly installed or missing center display screen grommets, causing contact between the center display screen and the instrument panel ambient light bar.

- Resolves black screen issue caused when there is no SiriusXM disk space.

(OFF/AUTO/fan speed number) changes to a different language character or symbol.

and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC.

Escape and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC"

strategy - Improved SYNC stabilty. "

or minor feature code DBCBC for Corsair may exhibit various driver assistance feature warning messages displayed in the IPC.

diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.

-23 MY Corrects nuisance DTC (Electronic Horizion Availibility)

Reason for update: update the Parts list to correct a part description " Loctite 638", update the claim quantity for the drain/fill plug, update the claim quantity of the wheel hub bolts (Corsair) and limited the parts list for Edge/Nautilus to only the rear drive unit fluid. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions:  Shudder chatter condition, most noticeable at low speeds turning  No relevant diagnostic trouble codes (DTCs) present This may be due to internal rear drive unit (RDU) fluid contamination.

the causal part, a new lower level part is available. It is no longer necessary to replace the air registers if only the HVAC air register arm or linkage are damaged.<br /> <br /> Drivers side (LJ7Z-78045K00-A)<br /> Left center (LJ7Z-78045K00-B)<br /> Right center (LJ7Z-78045K00-C)<br /> Passenger side (LJ7Z-78045K00-D)

Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.