2026 Lincoln Aviator TSBs

with the auto folding mirror functionality not matching the status selected by the switch in the center display screen menu. Examples include mirror auto folding not operating when the switch is enabled and/or auto folding continuing to function when the switch is disabled. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). Power folding mirror operation from the physical button is not affected by this condition. Inform customers that engineering is currently working on a solution for this condition that is expected by the end of Q2 2027. Replacement or reprogramming of the accessory protocol interface module (APIM), DDM, or PDM will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.<br /><br /> If the vehicle exhibits this condition, submit a Vehicle Concern Report. To submit a report, click on the "Submit G

the front engine cover removed and reinstalled for various reasons. The Workshop Manual (WSM), Section 303-01 Engine > Removal and Installation > Engine Front Cover service procedure has been updated to include a new essential special service tool (ESST) guide pin alignment tool (303-1790) that is used to align the engine front cover to the engine block, preventing the O-ring seal on the engine oil galley feed tube from getting damaged during installation.

> Front Seats > Diagnosis and Testing lead to the replacement of the front seat cushion extension adjuster, a lower-level part is now available (14C720). It is not necessary to replace the front seat cushion extension adjuster if only the front seat cushion extension motor assembly is damaged. For Corsair, use service part LJ7Z-14C720-A. For Aviator, use service part R2TZ-14C720-A. For 2025-2026 Navigator (both sides) and 2018-2024 Navigator driver side, use service part NL7Z-14C720-A. For 2018-2024 Navigator passenger side, use service part NL7Z-14C720-B.

connection or general Bluetooth pairing concerns for both Android and IOS after an APIM software update. This may be due to the APIM software. To temporarily correct the issue:<br /><br /> * For Android Auto related issues: Clear Android Auto app storage in the center display screen. Vehicle Settings > Settings > Apps > Android Auto > Clear Storage. <br /> * For general Bluetooth connectivity issues: Clear Contacts Storage app storage in the center display screen. Vehicle Settings > Apps > Uncheck hide system apps > Contacts Storage > Clear Storage.<br /><br /> If the condition persists, perform a master reset from the center display screen, remove the vehicle from the phone, then re-pair the device.<br /><br /> If the condition continues to persist, refer to Workshop Manual (WSM), Section 415-00 for normal diagnostics and repair as necessary outside of this article.<br /><br /> If the condition is resolved, inform customers that engineering is currently working on a permanent solution

BlueCruise feature intermittently/consistently unavailable when BlueCruise is active and when traveling in a "Blue Zone". Speed sign recognition may also be inaccurate. If there are no active relevant diagnostic trouble codes (DTC) present and the issue persists after multiple key cycles and if the BlueCruise System Health Check passes, download and run the "TCU - Reset Telematics Control Unit (TCU) Module" application using the latest software level of the Ford Diagnosis and Repair System (FDRS). If the condition is resolved, inform customers that this may be a temporary fix and engineering is currently working on a solution expected in Q4 2026. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. For claiming, use causal 14G229 and labor operations 12651D and 12651D4. If the condition persists after a test drive, refer to Workshop Manual (WSM), Section 419-03B for normal

feature intermittently/consistently unavailable when BlueCruise is active and when traveling in a "Blue Zone". Speed sign recognition may also be inaccurate. If there are no active relevant diagnostic trouble codes (DTC) present and the issue persists after multiple key cycles and if the BlueCruise System Health Check passes, download and run the "TCU - Reset Telematics Control Unit (TCU) Module" application using the latest software level of the Ford Diagnosis and Repair System (FDRS). If the condition is resolved, inform customers that this may be a temporary fix and engineering is currently working on a solution expected in Q4 2026. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. For claiming, use causal 14G229 and labor operations 12651D and 12651D4. If the condition persists after a test drive, refer to Workshop Manual (WSM), Section 419-03B for normal diagnosti

13-Dec-2025 may exhibit various drivability symptoms including a rough idle or hesitation shortly after refueling. These symptoms may also be accompanied by liquid fuel in the fuel vapor lines and fuel vapor canister as well as an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0133, P0300, P0301, P0302, P0303, P0304, P0305, and/or P0306 stored in the powertrain control module (PCM). This condition may be due to an intermittently sticking fuel level vent valve on the fuel tank allowing fuel to enter the evaporative emissions system lines and evaporative emissions canister during refueling. If the customer states that the drivability symptoms occurred after recently filling the vehicle, replace the fuel tank (9002) and evaporative emissions canister (9D653). Refer to Workshop Manual (WSM), Section 310-01 to replace the fuel tank. Refer to WSM, Section 303-13 to replace the evaporative emission canister. For claiming use causal part 9002 and labor operations 90

trouble codes (DTC) B144D:29, B144E:29, B1555:29, B1556:29 and/or U3003:16 stored in the rear gate trunk module (RGTM). The power liftgate may also be inoperative. This may be due to water intrusion into the left and/or right power liftgate motors caused by a loose grommet on the electrical harness at the body pass-through. To correct this condition, install a new power liftgate motor corresponding to the DTC(s) set in the RGTM (B144D:29/B144E:29 left or B1555:29/B1556:29 right). To prevent water intrusion into the new liftgate motor, make sure the grommet on the new motor is seated properly by pushing on the grommet at the body pass-through until it clicks into place. For claiming, use causal part 14B351 (Explorer) or 14B350 (Aviator) and labor operations 12651D and 14350AL (left) or 14350AR (right) or 14350AT (both) <br /><br /> If a vehicle with this concern exhibits water intrusion, corrosion, or unseated grommets in or around the liftgate motor, submit a Global Concern Report

start feature using either the key fobs or the Ford/Lincoln App. This may be due to the software in the body control module (BCM). After replicating the concern, use the Ford Diagnosis and Repair System (FDRS) to monitor the RMTSTRT_F_ARB_LST and RMTSTRT_F_TRGT_NM parameter identification (PIDS) in the BCM. If both PID values show "true" in any of the last 5 saved values, engineering is currently working on a solution for this condition that is expected in Q4 2026. Schedule service appointments for customers once the repair becomes available. If either of the BCM PID values do not show "true" in any of the saved values, refer to Workshop Manual (WSM), Section 501-14 Handles, Locks, Latches, Entry Systems > Diagnosis and Testing > Locks, Latches and Entry Systems > Pinpoint Test R (Explorer/Aviator)/Pinpoint Test V (Expedition/Navigator) for normal diagnostics and repair as necessary outside of this article. For claiming, use causal part 15604 and labor operations 12651D and 12651D45

(MIL) lamp with engine over-temperature warning in the message center and poor air conditioning (A/C) performance from the engine cooling fan not running. Diagnostic trouble codes (DTC) B3A1B, P0113, P0217, and/or P0480 may be stored in the powertrain control module (PCM). This may be due to poor engine compartment ground connections at G105, G107, G111 and/or G122. Refer to the Wiring Diagram (WD) > Grounds Cell 010 > Pages 2, 3, 7 and 8. Prior to any Workshop Manual (WSM) diagnostics, verify all listed grounds are tightened to 62 lb-in (7 Nm) to resolve this condition. If symptoms or DTCs return after all grounds are tightened, follow normal WSM diagnostics.

vehicles equipped with a 3.0/3.3L engine may require various repairs associated with the fuel tank and/or fuel pump and sender unit. Workshop Manual (WSM), Section 310-00 > Removal and Installation for the fuel tank and fuel pump and sender unit have been revised to eliminate the need to remove the driveshaft as part of the service procedure. Labor times have also been updated to reflect this WSM revision.

feature code IDBBN) may exhibit a no audio/sound condition with no communication with the audio digital signal processing (DSP) module. Remove the DSP fuse from the battery junction box (BCMC) (F40 for Aviator, F5 for Navigator, F138 for Nautilus). Inspect the fuse for an open and ensure the fuse has proper blade contact. After one minute, reinstall the good fuse. If the concern is still present or a fuse concern is found, continue with normal Workshop Manual (WSM) diagnostics, Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing. If communication has been re-established with the DSP module, engineering is currently working on a solution for this condition that is expected by Q2 2026. Replacement or reprogramming of the DSP will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. For claiming, use causal part 18B849

in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.

with the auto folding mirror functionality not matching the status selected by the switch in the center display screen menu. Examples include auto folding not operating when the switch is enabled and/or auto folding continuing to function when the switch is disabled. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). Power folding mirror operation from the physical button is not affected by this condition. Inform customers that engineering is currently working on a solution for this condition that is expected in Q4 2026. Replacement or reprogramming of the accessory protocol interface module (APIM), DDM, or PDM will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.<br /><br /> If the vehicle exhibits this condition, submit a Vehicle Concern Report. To submit a report, click on the "Submit Global Concern Report"

during an inbound phone call using CarPlay, the person in the vehicle cannot be heard. This may be due to the software in the accessory protocol interface module (APIM). Replacement or reprogramming of the APIM will not resolve this condition. Inform customers that engineering is currently working on a software solution for this condition and will be released via a software update delivered over-the-air (OTA) expected by April 2026. The software will update automatically if vehicle connectivity is enabled in the vehicle settings. Schedule a service visit for customers who have disabled vehicle connectivity or who report that they did not receive the update by May 2026. Monitor Professional Technician System (PTS) for additional information.

module (PCM) when a diagnostic self-test is performed. This may be due to a software update delivered via over the air (OTA). If multiple DTCs are present due to other concerns, diagnose those prior to addressing U0103:00:80. If other DTCs are not present, clear DTC U0103:00:80 before following the workshop manual (WSM) DTC diagnostics. If DTC U0103:00:80 does not return after clearing, no further action is required. Return the vehicle to the customer. If DTC U0103:00:80 does return after clearing, proceed with normal diagnostics in the WSM. Ford Engineering is currently developing a software update to resolve this condition. The software update is expected to be released and delivered via OTA in Q2 of 2026. Monitor Professional Technician System (PTS) for additional information.

exhibit a no audio/sound condition with no communication with the audio digital signal processing (DSP) module. This may be due to the software in the DSP. To determine if it is a software concern, remove the DSP fuse from the battery junction box (BCMC) (F40 for Aviator or F5 for Navigator). Inspect the fuse for an open and ensure the fuse has proper blade contact. After one minute, reinstall the good fuse. If the concern is still present or a fuse concern is found, continue with normal Workshop Manual (WSM) diagnostics, Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing. If communication has been re-established with the DSP module, engineering is currently working on a solution for this condition that is expected by Q2 2026. Replacement or reprogramming of the DSP will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available

built on or after 02-Feb-2025 * 2025-2026 Explorer/Aviator built on or after 02-Feb-2025 * 2025-2026 Nautilus built on or after 17-Feb-2025 * 2025-2026 F-150 built on or after 16-Jul-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC) - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, manually enter the vehicle identification number (VIN) into the VIN entry dialog in the Ford Diagnosis and Repair System (FDRS) and then start a session using the Vehicle Communication Module (VCM) II, VCM 3, Vehicle Communication and Measurement Module (VCMM) or later level device with a universal serial bus (USB) cable disconnected from the laptop. Download the "BCM - Body Control Module (BCM) Hardware Test" app

system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration

Reason for update: To remove the M6 nut from the part list and remove the Steps to install the M6 nut from the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * "Steering Assist Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008:1B and/or U3009:1B stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.

IDBBN) and 2025-2026 Navigator vehicles may exhibit a no audio/sound condition with no communication with the audio digital signal processing module (DSP) with U0238 stored in the audio control module (ACM). This may be due to the DSP. To determine if the DSP is the root cause, remove the DSP fuse from the battery junction box (BCMC fuse F40 for Aviator, BCMC fuse F138 for Nautilus, BJB fuse F5 for Navigator). Inspect the fuse for an open and make sure the fuse has proper blade contact. After one minute, reinstall the good fuse. If the concern is still present or a fuse concern is found, refer to Workshop Manual (WSM), Section 415-00 for normal diagnostics. If communication has been re-established with the DSP, install a new DSP ordered from Ford Component Sales using the On-Line 1878 form to correct this condition. Refer to Workshop Manual (WSM), Section 415-00. For claiming, use causal part 18B849 and labor operations 12651D and 12651D13.

exhibit concerns with the passenger mirror not automatically folding in or out at times, while the driver side mirror automatically folds properly. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 14B291 and labor operation MT14B291SSM up to 0.4 hours.

IDBBN) and 2025-2026 Navigator vehicles may exhibit a no audio/sound condition with no communication with the audio digital signal processing module (DSP) with U0238 stored in the audio control module (ACM). This may be due to the DSP. To determine if the DSP is the root cause, remove the DSP fuse from the battery junction box (BCMB fuse F40 for Aviator, BCMB fuse F138 for Nautilus, BJB fuse F5 for Navigator). Inspect the fuse for an open and make sure the fuse has proper blade contact. After one minute, reinstall the good fuse. If the concern is still present or a fuse concern is found, refer to Workshop Manual (WSM), Section 415-00 for normal diagnostics. If communication has been re-established with the DSP, install a new DSP ordered from Ford Component Sales using the On-Line 1878 form to correct this condition. Refer to Workshop Manual (WSM), Section 415-00. For claiming, use causal part 18B849 and labor operations 12651D and 12651D13.

Reason for update: To update vehicle symptoms, affected vehicle lines, and model years. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:  Poor speaker sound quality (static, pop, crackle) while using Apple CarPlay or Bluetooth audio  Poor or muffled outbound phone call sound quality while using Apple CarPlay or Bluetooth audio This may be due to the software in the accessory protocol interface module (APIM).

condition with no communication with the audio digital signal processing (DSP) module with U0238 stored in the audio control module (ACM). This may be due to the DSP. To determine if the DSP is the root cause, remove the DSP fuse from the battery junction box (BCMB fuse F40). Inspect the fuse for an open and make sure the fuse has proper blade contact. After one minute, reinstall the good fuse. If the concern is still present or a fuse concern is found, refer to Workshop Manual (WSM), Section 415-00 for normal diagnostics. If communication has been re-established with the DSP, install a new DSP ordered from Ford Component Sales using the On-Line 1878 form to correct this condition. For claiming, use causal part 18B849 and labor operations 12651D and 12651D13. <br /><br /> To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System

Reason for update: update the Service Procedure to add figures 1, 2, 5 and 6 to clarify the ground location, update Steps (13-15, 21-22), and update the Parts list according to the type of vehicle variant and repair. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * "Steering Assist Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008:1B and/or U3009:1B stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * "Steering Assist Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008:1B and/or U3009:1B stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.

Start Assist Not Available" message in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) B1262:92 stored in multiple door latch control modules (DCME, DCMF, DCMG, and/or DCMH). DTC U0504 may also be stored in the gearshift module (GSM). This may be due to the software in the door latch control modules. To correct this condition, download and run the following applications using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool.<br /> "DCME - Door Control Module E (DCME) Software Update"<br /> "DCMF - Door Control Module F (DCMF) Software Update"<br /> "DCMG - Door Control Module G (DCMG) Software Update"<br /> "DCMH - Door Control Module H (DCMH) Software Update"<br /> For claiming use causal part 54219A65 and labor operation MT54219SSM up to 0.5 hours.

Start Assist Not Available" message in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) B1262:92 stored in multiple door latch control modules (DCME, DCMF, DCMG, and/or DCMH). DTC U0504 may also be stored in the gearshift module (GSM). This may be due to the software in the door latch control modules. To correct this condition, download and run the following applications using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. "DCME - Door Control Module E (DCME) Software Update" "DCMF - Door Control Module F (DCMF) Software Update" "DCMG - Door Control Module G (DCMG) Software Update" "DCMH - Door Control Module H (DCMH) Software Update" For claiming use causal part 54219A65 and labor operation MT54219SSM up to 0.5 hours.

introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.

Replacement

Transmission Replacement

Reason for update: add 2026 model year vehicles and Transit, update the causal part number (15604), update the Service Procedure, update the service labor operations for 2023 F-Super Duty, and add service labor operations for Transit. Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.

crackling and/or distorted sound from one or more speakers (but not all speakers). This may be due to other components located near the suspect speaker. Workshop Manual (WSM), Section 415-00 > Diagnosis and Testing > Pinpoint Test D (2020-2024 Explorer/Police Interceptor Utility, 2025-2026 Aviator) and Pinpoint Test E (2020-2024 Aviator, 2025-2026 Explorer/Police Interceptor Utility) have been updated with additional direction when isolating the cause of the condition.

HKCGA) may experience a blank/white Google map screen, inoperative live traffic data, inoperative voice assistant, the inability to sign into a Google account in the center touch screen, unable to access the Google Play Store in the center display screen, and/or the inability to connect to other apps in the center display screen. This may be due to the vehicles Connectivity Package not being activated. To verify if the vehicle has an active Connectivity Package (free or paid) enter the vehicle identification number (VIN) in Professional Technician System (PTS) then navigate to the upper blue tab titled Connected Vehicle > Vehicle Software Subscriptions. It will clearly state if the vehicle has a trial or paid subscription, along with the expiration date. The customer can check subscription status from the Connected Services tile located within The Lincoln App. These vehicles come with a free Connectivity Package that lasts for 4 years. To activate the free trial period or to subscribe

vehicles built on or after 24-Apr-2025 are no longer equipped with the passenger side underbody air deflector. The vehicle is not misbuilt. Do not submit a claim for this condition.

Aviator Vehicles Windshield Replacement

system has lost position memory and is stuck in a middle-latch position

inner/outer CV joint boot for various reasons. If Workshop Manual (WSM), Section 205-04 > Diagnosis and Testing leads to CV joint boot replacement, L1MZ-3A331-G (Explorer/Police Interceptor Utility front inner/outer CV joint boot kit), L1MZ-3A331-H (Aviator front inner/outer CV joint boot kit), L1MZ-3A331-F (Explorer/Police Interceptor Utility front inner CV joint boot kit) and L1MZ-3A331-E (Aviator front inner CV joint boot kit) have been released for service. Refer to WSM, Section 205-04 for Removal and Installation procedures.

key fob indicating that the vehicle has remote started (or not remote started). Factory key fobs with remote start no longer contain an LED feedback indicator. Do not replace the key fob for this condition. This is a normal operating characteristic and no service action is necessary.

Navigation System (minor feature code HKCGA) may experience a blank screen for Google Maps or the absence of live traffic data. To correct this condition, refer to the Workshop Manual (WSM), Section 415-00 > Diagnosis and Testing > Information and Entertainment System. The WSM has been updated with improved diagnostics for this condition. To confirm whether a vehicle is built with a specific minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner of the Professional Technician System (PTS).