2025 Lincoln Aviator TSBs

This may be due to a concern with the front courtesy lamp light module.

diagnostic trouble code (DTC) U211B:43:48 stored in the body control module (BCM) when performing a Self-Test. This DTC sets due to an internal BCM timing issue during the self-test process. This specific code has no customer impact and does not cause any drivability concerns or warning messages. Clearing DTC U211B:43:48, reprogramming the BCM, or replacing the BCM is unlikely to prevent this DTC from setting. This DTC does not trigger a condition covered under warranty. Note: This guidance only applies to U211B with the specific failure byte 43 in status 48. Any other trusted real-time operation network (TRON) DTCs or different failure bytes associated with U211B are still applicable and technicians must follow Workshop Manual (WSM) normal diagnostics for those DTCs.

message and diagnostic trouble codes (DTC) C1110:56 and/or U3000:96 stored in the power steering control module (PSCM) after programming. This may be due to a calibration mismatch in the PSCM which has been resolved in the Ford database. If DTC C1110:56 is stored in a replacement PSCM after completing programmable module installation (PMI), start a new session using the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool then run the "PSCM - Programmable Module Installation (PMI)" application again. When FDRS asks if the original module is installed, select "No". If DTC C1110:56 is stored in the original PSCM after performing the PSCM configuration, start a new session using the latest software version of the FDRS scan tool, then download and run the "PSCM - Power Steering Control Module (PSCM) Software Update" application. To clear DTC U3000:96 from the PSCM, download and run the "PSCM - Reset the Power Steering Control

Ranger/Bronco/Mustang * 2024-2025 F-150 built on or before 15-Jul-2025 * 2024-2025 Nautilus built on or before 16-Feb-2025 * 2025 Explorer/Aviator built on or before 01-Feb-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC). - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, start the vehicle using both key fobs. If the no crank/no start condition with "No Key Detected" concern is present, reprogram both key fobs and retest. If the no crank/no start condition with "No Key Detected" is still present, replace the body control module (BCM). Refer to Workshop Manual (WSM), Section 419-10. For claiming, use causal part 15604 and labor operation MT55118SSM up to 1.8 hours.

built on or after 02-Feb-2025 * 2025-2026 Explorer/Aviator built on or after 02-Feb-2025 * 2025-2026 Nautilus built on or after 17-Feb-2025 * 2025-2026 F-150 built on or after 16-Jul-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC) - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, manually enter the vehicle identification number (VIN) into the VIN entry dialog in the Ford Diagnosis and Repair System (FDRS) and then start a session using the Vehicle Communication Module (VCM) II, VCM 3, Vehicle Communication and Measurement Module (VCMM) or later level device with a universal serial bus (USB) cable disconnected from the laptop. Download the "BCM - Body Control Module (BCM) Hardware Test" app

enhancement

battery drain that occurs only when ambient outdoor temperature is greater than 90F (32C). This may be due to the camera module - rear (CMR) keeping the flexible data rate controller area network 3 (FD-CAN3) awake. To correct this condition, download and run the "CMR - Driver Status Monitor Camera Module CMR Software Update" application using the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 3G592 and labor operation MT3G592SSM up to 1.8 hours.

Expedition, Bronco Sport, Explorer, Bronco, Navigator, and Aviator Vehicles Powertrain Control Module Software Update

system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration

Reason for update: To remove the M6 nut from the part list and remove the Steps to install the M6 nut from the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * "Steering Assist Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008:1B and/or U3009:1B stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.

IDBBN) and 2025-2026 Navigator vehicles may exhibit a no audio/sound condition with no communication with the audio digital signal processing module (DSP) with U0238 stored in the audio control module (ACM). This may be due to the DSP. To determine if the DSP is the root cause, remove the DSP fuse from the battery junction box (BCMC fuse F40 for Aviator, BCMC fuse F138 for Nautilus, BJB fuse F5 for Navigator). Inspect the fuse for an open and make sure the fuse has proper blade contact. After one minute, reinstall the good fuse. If the concern is still present or a fuse concern is found, refer to Workshop Manual (WSM), Section 415-00 for normal diagnostics. If communication has been re-established with the DSP, install a new DSP ordered from Ford Component Sales using the On-Line 1878 form to correct this condition. Refer to Workshop Manual (WSM), Section 415-00. For claiming, use causal part 18B849 and labor operations 12651D and 12651D13.

exhibit concerns with the passenger mirror not automatically folding in or out at times, while the driver side mirror automatically folds properly. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 14B291 and labor operation MT14B291SSM up to 0.4 hours.

IDBBN) and 2025-2026 Navigator vehicles may exhibit a no audio/sound condition with no communication with the audio digital signal processing module (DSP) with U0238 stored in the audio control module (ACM). This may be due to the DSP. To determine if the DSP is the root cause, remove the DSP fuse from the battery junction box (BCMB fuse F40 for Aviator, BCMB fuse F138 for Nautilus, BJB fuse F5 for Navigator). Inspect the fuse for an open and make sure the fuse has proper blade contact. After one minute, reinstall the good fuse. If the concern is still present or a fuse concern is found, refer to Workshop Manual (WSM), Section 415-00 for normal diagnostics. If communication has been re-established with the DSP, install a new DSP ordered from Ford Component Sales using the On-Line 1878 form to correct this condition. Refer to Workshop Manual (WSM), Section 415-00. For claiming, use causal part 18B849 and labor operations 12651D and 12651D13.

Reason for update: To update vehicle symptoms, affected vehicle lines, and model years. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:  Poor speaker sound quality (static, pop, crackle) while using Apple CarPlay or Bluetooth audio  Poor or muffled outbound phone call sound quality while using Apple CarPlay or Bluetooth audio This may be due to the software in the accessory protocol interface module (APIM).

battery drain that occurs only when ambient outdoor temperature is greater than 90F (32C). This may be due to the camera module - rear (CMR) keeping the flexible data rate controller area network 3 (FD-CAN3) awake. To correct this condition, download and run the "CMR - Driver Status Monitor Camera Module CMR Software Update" application using the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 3G592 and labor operations 12651D and 12651D4.

condition with no communication with the audio digital signal processing (DSP) module with U0238 stored in the audio control module (ACM). This may be due to the DSP. To determine if the DSP is the root cause, remove the DSP fuse from the battery junction box (BCMB fuse F40). Inspect the fuse for an open and make sure the fuse has proper blade contact. After one minute, reinstall the good fuse. If the concern is still present or a fuse concern is found, refer to Workshop Manual (WSM), Section 415-00 for normal diagnostics. If communication has been re-established with the DSP, install a new DSP ordered from Ford Component Sales using the On-Line 1878 form to correct this condition. For claiming, use causal part 18B849 and labor operations 12651D and 12651D13. <br /><br /> To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System

Reason for update: update the Service Procedure to add figures 1, 2, 5 and 6 to clarify the ground location, update Steps (13-15, 21-22), and update the Parts list according to the type of vehicle variant and repair. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * "Steering Assist Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008:1B and/or U3009:1B stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:  Poor speaker sound quality (static, pop, crackle) while using Bluetooth audio  Poor outbound phone call sound quality while using Bluetooth This may be due to the APIM (accessory protocol interface module) software.

Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * "Steering Assist Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008:1B and/or U3009:1B stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.

least one of the following error messages in Ford Diagnosis and Repair System (FDRS) while programming the audio digital signal processing module (DSP):<br /><br /> * "Procedure Unsuccessful - ReadDTCs DTCs present: U2101 (Control Module Configuration Incompatible)"<br /> * "Procedure Unsuccessful - ReadDTCs DTCs present: U2100 (Initial Configuration Not Complete)"<br /> * "Procedure Unsuccessful - FlashSoftware Failed to flash RC5T-14C656-BH"<br /> * "ValidateFlashActionDIDsAgainstModule Update was not successful! FAIL - F10A = >>> SHOULD = RC5T-14C656-BH"<br /><br /> For any programming concerns not listed above, continue diagnosis outside this article. Refer to Workshop Manual, Section 418-01A > General Procedures.<br /><br /> This concern may be due to the software in the DSP. To correct this condition, program the DSP using the latest software level of the FDRS scan tool. For claiming, use causal part 18B849 and labor operations 12651D and 12651D4.<br /><br /> To co

Interface Module Software Update

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

speaker sound quality (static, pop, crackle) while using Bluetooth audio  Poor outbound phone call sound quality while using Bluetooth This may be due to the APIM (accessory protocol interface module) software.

This may be due to the configuration of the BCM with RU5T-14C184-AGY software. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". For vehicles with RU5T-14C184-AGY software in the BCM, download and run the "BCM - Body Control Module (BCM) Software Update" application using the latest version of the Ford Diagnosis and Repair System (FDRS) scan tool. For vehicles with any other software level in the BCM, refer to Workshop Manual (WSM), Section 501-14 to continue with normal diagnostics outside of this article. For claiming, use causal part 15604 and labor operations 12651D and 12651D4.

rear windows are unlocked when the child lock is on. This may be due to the software in the BCM. To correct this condition, download and run the "BCM - Body Control Module (BCM) Software Update" application using the latest version of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 15604 and labor operations 12651D and 12651D4.

message appearing in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) C1001:31 setting in the image processing module A (IPMA). This may be due to a loose or partial connection at the front windshield camera, connector C9449 on Explorer/Police Interceptor Utility and C9128 on Aviator. Check and verify this connection prior to starting Workshop Manual (WSM) Pinpoint Tests. If the connection is secure, continue with normal diagnostics.

Experience may exhibit a "Map Source Not Available" message on the instrument panel cluster display (IPC) when using Google Maps via Apple CarPlay. Google Maps does not yet support displaying the navigation map on the IPC within the Apple CarPlay environment and this is currently the expected behavior. Replacing or reprogramming the accessory protocol interface module (APIM) will not resolve this condition and no diagnosis or repair is necessary. Inform the customer that a future Google Maps update for iPhone is anticipated to enable this functionality. This update will be delivered directly through the Google Maps app on their iPhone and will not require an over the air (OTA) software update or dealership visit.

Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:  Inbound call cannot be heard  Wireless charger icon inaccurate  Auto hold, auto start-stop, and/or defrost button LED indicators inoperative This may be due to the accessory protocol interface module (APIM) software.

Some of the vehicles listed in the Model statement above may exhibit driver assistance feature warning messages displayed in the instrument panel cluster (IPC). Additionally, some modules may store invalid data/lost communication diagnostic trouble codes (DTCs). This may be due to software in the image processing module A (IPMA).

control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.

Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008 and/or U3009 stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.

feature code IDBBN) may exhibit a no audio/sound condition with no communication with the DSP. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This concern may be due to the software in the DSP. To determine if it is a software concern, remove the DSP fuse, F40 for Aviator or F5 for Navigator, and inspect the fuse for an open and make sure the fuse has proper blade contact. After one minute, reinstall the good fuse. If the concern is still present or a fuse concern is found, continue with normal Workshop Manual diagnostics, Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing. If communication has been re-established with the DSP, reprogram the DSP using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 18B849

displayed in the instrument panel cluster (IPC). Additionally, some modules may store invalid data/lost communication diagnostic trouble codes (DTCs). This may be due to software in the image processing module A (IPMA).

Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:  Inbound call cannot be heard  Wireless charger icon inaccurate  Auto hold, auto start-stop, and/or defrost button LED indicators inoperative This may be due to the APIM (accessory protocol interface module) software.

or IDBBJ for Aviator) may exhibit a no audio/sound concern or programmable module installation (PMI) incomplete on a replacement DSP. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This concern may be due to software in the DSP. For vehicles with a no sound concern, reprogram the DSP using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. If the no sound concern continues, refer to Workshop Manual, Section 415-00 for further diagnosis. For error messages during PMI of a replacement DSP, attempt PMI again using the latest software level of the FDRS scan tool. For claiming, use causal part 18B849 and labor operations 12651D and 12651D4.

Additionally, some modules may store invalid data/lost communication diagnostic trouble codes (DTCs). The image processing module A (IPMA) should not store these DTCs. This condition may be due to the software in the IPMA causing no communication on the network. To restore communication/function, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) tool, then "Trusted Real-Time Operation Network (TRON) Module Authentication" following FDRS screen instructions. Next, download and run the "IPMA - Image Processing Module A (IPMA) Alignment" app, recheck DTCs and confirm that all warning messages are cleared from the IPC. For vehicles equipped with a 360 degree camera, perform the "360 Degree View Camera Alignment" procedure in Workshop Manual (WSM), Section 413-13. If these steps correct the condition, release the vehicle back to the customer.

codes (DTCs) U211A, U211B, U211C, U3034, U3035, U3036, U35D9, U35DA and/or U35DB if the secret authentication security keys are not aligned between the modules, a loss of communication is occurring between modules and/or a module is not responding. This may be a result of missing the new module secret authentication security key obtained when running the Ford Diagnosis and Repair System (FDRS) "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure after replacement. When replacing a TRON capable module, run the FDRS "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure in the GWM tool box, not in the toolbox of the module with the DTC's, to distribute a new set of secret authentication security keys to all TRON-capable modules. Using the specific vehicle identification number (VIN), refer to Workshop Manual (WSM), Section 418-00 and 418-01 for updated DTCs, applicable TRON module listings and pinpoint tests.

message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTCs) B1041 and U2100 stored in the suspension control module A (SUMA). This may be due to the SUMA entering diagnostic service mode following suspension system diagnosis or repair. Clear DTCs using FDRS > "SUMA > Transport and Factory Mode Deactivation" function. For other DTCs refer to Workshop Manual (WSM) > Section 204-05 Vehicle Dynamic Suspension for normal diagnostics.

Service Required message in the instrument panel cluster (IPC) message center with no applicable diagnostic trouble codes (DTCs) present in the vehicle dynamics control module (VDM). This may be due to the software in the VDM. To correct this condition, update the VDM software to the latest level using the Ford Diagnosis and Repair Tool (FDRS) scan tool. For claiming, use causal part 18B008 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

call cannot be heard  Wireless charger icon inaccurate This may be Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Inbound call cannot be heard  Wireless charger icon inaccurate This may be due to the APIM (accessory protocol interface module) software due to the APIM (accessory protocol interface module) software.

codes (DTCs) U211A, U211B, U211C, U3034, U3035, U3036, U35D9, U35DA and/or U35DB if the secret authentication security keys are not aligned between the modules, a loss of communication is occuring between modules and/or a module is not responding. This may be a result of missing the new module secret authentication security key obtained when running the Ford Diagnosis and Repair System (FDRS) "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure after replacement. When replacing a TRON capable module, run the FDRS "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure to distribute a new set of secret authentication security keys to all TRON-capable modules. Using the specific VIN, refer to Workshop Manual (WSM), Section 418-00 and 418-01 for updated DTCs, applicable TRON module listings and pinpoint tests.

cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.

instrument panel cluster (IPC) message center with no applicable diagnostic trouble codes (DTCs) present in the vehicle dynamics control module (VDM).

off load battery drain caused by modules staying awake after key off"

(minor feature code IDBBN) may exhibit a no audio/sound condition with no communication with DSP.

buzzing/clicking/humming/ticking sound from the overhead console (OHC) and/or diagnostic trouble code (DTC) P24AE in the heating ventilation and air conditioning (HVAC) module.

illuminated entry function and/or reduced passive entry functionality. This may be due to the body control module (BCM) configuration.

applicable diagnostic trouble codes (DTCs) present in the vehicle dynamics control module (VDM).

(minor feature code IDBBN) may exhibit a no audio/sound condition with no communication with DSP. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS).

- Robustness action to prevent fault scenarios where ECG algorithm is draining the battery when vehicle is parked and only during key off events. "

with the auto folding mirror functionality not matching the status selected by the switch in the center display screen menu. Examples include mirror auto folding not operating when the switch is enabled and/or auto folding continuing to function when the switch is disabled. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). Power folding mirror operation from the physical button is not affected by this condition. Inform customers that engineering is currently working on a solution for this condition that is expected by the end of Q2 2027. Replacement or reprogramming of the accessory protocol interface module (APIM), DDM, or PDM will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.<br /><br /> If the vehicle exhibits this condition, submit a Vehicle Concern Report. To submit a report, click on the "Submit G

the front engine cover removed and reinstalled for various reasons. The Workshop Manual (WSM), Section 303-01 Engine > Removal and Installation > Engine Front Cover service procedure has been updated to include a new essential special service tool (ESST) guide pin alignment tool (303-1790) that is used to align the engine front cover to the engine block, preventing the O-ring seal on the engine oil galley feed tube from getting damaged during installation.

> Front Seats > Diagnosis and Testing lead to the replacement of the front seat cushion extension adjuster, a lower-level part is now available (14C720). It is not necessary to replace the front seat cushion extension adjuster if only the front seat cushion extension motor assembly is damaged. For Corsair, use service part LJ7Z-14C720-A. For Aviator, use service part R2TZ-14C720-A. For 2025-2026 Navigator (both sides) and 2018-2024 Navigator driver side, use service part NL7Z-14C720-A. For 2018-2024 Navigator passenger side, use service part NL7Z-14C720-B.

connection or general Bluetooth pairing concerns for both Android and IOS after an APIM software update. This may be due to the APIM software. To temporarily correct the issue:<br /><br /> * For Android Auto related issues: Clear Android Auto app storage in the center display screen. Vehicle Settings > Settings > Apps > Android Auto > Clear Storage. <br /> * For general Bluetooth connectivity issues: Clear Contacts Storage app storage in the center display screen. Vehicle Settings > Apps > Uncheck hide system apps > Contacts Storage > Clear Storage.<br /><br /> If the condition persists, perform a master reset from the center display screen, remove the vehicle from the phone, then re-pair the device.<br /><br /> If the condition continues to persist, refer to Workshop Manual (WSM), Section 415-00 for normal diagnostics and repair as necessary outside of this article.<br /><br /> If the condition is resolved, inform customers that engineering is currently working on a permanent solution

13-Dec-2025 may exhibit various drivability symptoms including a rough idle or hesitation shortly after refueling. These symptoms may also be accompanied by liquid fuel in the fuel vapor lines and fuel vapor canister as well as an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0133, P0300, P0301, P0302, P0303, P0304, P0305, and/or P0306 stored in the powertrain control module (PCM). This condition may be due to an intermittently sticking fuel level vent valve on the fuel tank allowing fuel to enter the evaporative emissions system lines and evaporative emissions canister during refueling. If the customer states that the drivability symptoms occurred after recently filling the vehicle, replace the fuel tank (9002) and evaporative emissions canister (9D653). Refer to Workshop Manual (WSM), Section 310-01 to replace the fuel tank. Refer to WSM, Section 303-13 to replace the evaporative emission canister. For claiming use causal part 9002 and labor operations 90

trouble codes (DTC) B144D:29, B144E:29, B1555:29, B1556:29 and/or U3003:16 stored in the rear gate trunk module (RGTM). The power liftgate may also be inoperative. This may be due to water intrusion into the left and/or right power liftgate motors caused by a loose grommet on the electrical harness at the body pass-through. To correct this condition, install a new power liftgate motor corresponding to the DTC(s) set in the RGTM (B144D:29/B144E:29 left or B1555:29/B1556:29 right). To prevent water intrusion into the new liftgate motor, make sure the grommet on the new motor is seated properly by pushing on the grommet at the body pass-through until it clicks into place. For claiming, use causal part 14B351 (Explorer) or 14B350 (Aviator) and labor operations 12651D and 14350AL (left) or 14350AR (right) or 14350AT (both) <br /><br /> If a vehicle with this concern exhibits water intrusion, corrosion, or unseated grommets in or around the liftgate motor, submit a Global Concern Report

start feature using either the key fobs or the Ford/Lincoln App. This may be due to the software in the body control module (BCM). After replicating the concern, use the Ford Diagnosis and Repair System (FDRS) to monitor the RMTSTRT_F_ARB_LST and RMTSTRT_F_TRGT_NM parameter identification (PIDS) in the BCM. If both PID values show "true" in any of the last 5 saved values, engineering is currently working on a solution for this condition that is expected in Q4 2026. Schedule service appointments for customers once the repair becomes available. If either of the BCM PID values do not show "true" in any of the saved values, refer to Workshop Manual (WSM), Section 501-14 Handles, Locks, Latches, Entry Systems > Diagnosis and Testing > Locks, Latches and Entry Systems > Pinpoint Test R (Explorer/Aviator)/Pinpoint Test V (Expedition/Navigator) for normal diagnostics and repair as necessary outside of this article. For claiming, use causal part 15604 and labor operations 12651D and 12651D45

(MIL) lamp with engine over-temperature warning in the message center and poor air conditioning (A/C) performance from the engine cooling fan not running. Diagnostic trouble codes (DTC) B3A1B, P0113, P0217, and/or P0480 may be stored in the powertrain control module (PCM). This may be due to poor engine compartment ground connections at G105, G107, G111 and/or G122. Refer to the Wiring Diagram (WD) > Grounds Cell 010 > Pages 2, 3, 7 and 8. Prior to any Workshop Manual (WSM) diagnostics, verify all listed grounds are tightened to 62 lb-in (7 Nm) to resolve this condition. If symptoms or DTCs return after all grounds are tightened, follow normal WSM diagnostics.

vehicles equipped with a 3.0/3.3L engine may require various repairs associated with the fuel tank and/or fuel pump and sender unit. Workshop Manual (WSM), Section 310-00 > Removal and Installation for the fuel tank and fuel pump and sender unit have been revised to eliminate the need to remove the driveshaft as part of the service procedure. Labor times have also been updated to reflect this WSM revision.

feature code IDBBN) may exhibit a no audio/sound condition with no communication with the audio digital signal processing (DSP) module. Remove the DSP fuse from the battery junction box (BCMC) (F40 for Aviator, F5 for Navigator, F138 for Nautilus). Inspect the fuse for an open and ensure the fuse has proper blade contact. After one minute, reinstall the good fuse. If the concern is still present or a fuse concern is found, continue with normal Workshop Manual (WSM) diagnostics, Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing. If communication has been re-established with the DSP module, engineering is currently working on a solution for this condition that is expected by Q2 2026. Replacement or reprogramming of the DSP will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. For claiming, use causal part 18B849

in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.

with the auto folding mirror functionality not matching the status selected by the switch in the center display screen menu. Examples include auto folding not operating when the switch is enabled and/or auto folding continuing to function when the switch is disabled. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). Power folding mirror operation from the physical button is not affected by this condition. Inform customers that engineering is currently working on a solution for this condition that is expected in Q4 2026. Replacement or reprogramming of the accessory protocol interface module (APIM), DDM, or PDM will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.<br /><br /> If the vehicle exhibits this condition, submit a Vehicle Concern Report. To submit a report, click on the "Submit Global Concern Report"

during an inbound phone call using CarPlay, the person in the vehicle cannot be heard. This may be due to the software in the accessory protocol interface module (APIM). Replacement or reprogramming of the APIM will not resolve this condition. Inform customers that engineering is currently working on a software solution for this condition and will be released via a software update delivered over-the-air (OTA) expected by April 2026. The software will update automatically if vehicle connectivity is enabled in the vehicle settings. Schedule a service visit for customers who have disabled vehicle connectivity or who report that they did not receive the update by May 2026. Monitor Professional Technician System (PTS) for additional information.

module (PCM) when a diagnostic self-test is performed. This may be due to a software update delivered via over the air (OTA). If multiple DTCs are present due to other concerns, diagnose those prior to addressing U0103:00:80. If other DTCs are not present, clear DTC U0103:00:80 before following the workshop manual (WSM) DTC diagnostics. If DTC U0103:00:80 does not return after clearing, no further action is required. Return the vehicle to the customer. If DTC U0103:00:80 does return after clearing, proceed with normal diagnostics in the WSM. Ford Engineering is currently developing a software update to resolve this condition. The software update is expected to be released and delivered via OTA in Q2 of 2026. Monitor Professional Technician System (PTS) for additional information.

exhibit a no audio/sound condition with no communication with the audio digital signal processing (DSP) module. This may be due to the software in the DSP. To determine if it is a software concern, remove the DSP fuse from the battery junction box (BCMC) (F40 for Aviator or F5 for Navigator). Inspect the fuse for an open and ensure the fuse has proper blade contact. After one minute, reinstall the good fuse. If the concern is still present or a fuse concern is found, continue with normal Workshop Manual (WSM) diagnostics, Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing. If communication has been re-established with the DSP module, engineering is currently working on a solution for this condition that is expected by Q2 2026. Replacement or reprogramming of the DSP will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available

Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.

light"

Module (PCM) Software Update

turbocharger oil supply tube due to various concerns.

off when placed into gear.

exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P219A (Bank 1 Air-Fuel Ratio Imbalance) and/or P219B (Bank 2 Air-Fuel Ratio Imbalance) stored in the powertrain control module (PCM) with no effect on vehicle operation.

noise at idle and/or while driving.

engine over-temperature warning displayed in the IPC and an illuminated MIL with DTC P1299 along with P2C38 or P2C39 stored in the PCM.

vehicles equipped with a 2.7L EcoBoost or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.

(MIL) lamp with engine over-temperature warning in the message center and poor air conditioning (A/C) performance from the engine cooling fan not running.

equipped with a Titanium engine compartment and under hood finish, which may appear to be primer or unfinished.

while in transport mode with diagnostic trouble code (DTC) P112A stored in the powertrain control module (PCM). This may be due to excessive engine starts while the vehicle is in transport mode

vehicle's right (passenger) exterior mirror does not come out of the folded position after the vehicle is unlocked. This may be due to a software concern within the driver's door module (DDM) and passenger's door module (PDM). If the mirror unfolds after pressing the mirror fold button in the vehicle twice, inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q4 2024. Replacement or reprogramming of the DDM and PDM will not resolve this condition at this time.

headlamp control module (HCM) when a diagnostic self-test is performed. This may be due to a HCM communication error within a specified timeframe. DTC U211B:87 does not affect vehicle durability with no effect on vehicle operation and no additional diagnostics or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q3 2024. Replacement or reprogramming of the HCM will not resolve this condition.

If this DTC is identified during ePDI or normal diagnostics for various concerns, this DTC does not affect vehicle durability and no additional diagnosis or service is required for this DTC at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q4 2024. Replacement or reprogramming of these modules will not resolve this DTC.

the vehicle.

person in the vehicle cannot be heard.

And Through 07-Oct-2024 Some 2025 Aviator vehicles built on 29-Jul-2024 and through 07-Oct-2024 may exhibit an inoperative approach detection illuminated entry function and/or reduced passive entry functionality. "

reduced passive entry functionality.

entry feature; however, all remote keyless entry (RKE) physical button functionality works correctly and the second passive key will have full/correct functionality (including being able to start the vehicle):

displayed options are active and relevant.

Reason for update: add 2026 model year vehicles and Transit, update the causal part number (15604), update the Service Procedure, update the service labor operations for 2023 F-Super Duty, and add service labor operations for Transit. Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.

crackling and/or distorted sound from one or more speakers (but not all speakers). This may be due to other components located near the suspect speaker. Workshop Manual (WSM), Section 415-00 > Diagnosis and Testing > Pinpoint Test D (2020-2024 Explorer/Police Interceptor Utility, 2025-2026 Aviator) and Pinpoint Test E (2020-2024 Aviator, 2025-2026 Explorer/Police Interceptor Utility) have been updated with additional direction when isolating the cause of the condition.

HKCGA) may experience a blank/white Google map screen, inoperative live traffic data, inoperative voice assistant, the inability to sign into a Google account in the center touch screen, unable to access the Google Play Store in the center display screen, and/or the inability to connect to other apps in the center display screen. This may be due to the vehicles Connectivity Package not being activated. To verify if the vehicle has an active Connectivity Package (free or paid) enter the vehicle identification number (VIN) in Professional Technician System (PTS) then navigate to the upper blue tab titled Connected Vehicle > Vehicle Software Subscriptions. It will clearly state if the vehicle has a trial or paid subscription, along with the expiration date. The customer can check subscription status from the Connected Services tile located within The Lincoln App. These vehicles come with a free Connectivity Package that lasts for 4 years. To activate the free trial period or to subscribe

The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.

-Prevents a network communication error that may cause an error message in the center screen

panel cluster (IPC).

vehicles built on or after 24-Apr-2025 are no longer equipped with the passenger side underbody air deflector. The vehicle is not misbuilt. Do not submit a claim for this condition.

Aviator Vehicles Windshield Replacement

mirror with no vehicle or objects near the vehicle. This may be due to the radar signal echoing off the bumper cover and through the trailer hitch bar. **Additional information for model section** - Space White/Crystal White Metallic Exterior Paint (Paint Code A3)

built on or after 24-Apr-2025 are no longer equipped with the passenger side underbody air deflector. The vehicle is not misbuilt. Do not submit a claim for this condition.

entry, welcome lighting, or the hands-free liftgate upon approaching the vehicle while parked.

Aviator vehicles, use a clean soft cloth and locally available 50% isopropyl alcohol to remove adhesive residue.

system has lost position memory and is stuck in a middle-latch position

the Ford/Lincoln Digital Experience system. To perform a hard reset, press and release the volume button on the center console 5 times within 7 seconds. Some vehicles with older level software may require the volume button to be pressed and held for at least 5 seconds. The Owners Manual is in process of being updated with this information.

the Ford/Lincoln Digital Experience system. To perform a hard reset, press and release the volume button on the center console 5 times within 7 seconds. Some Nautilus vehicles with older level software, may require the volume button to be pressed and held for at least 5 seconds. The Owners Manual is in process of being updated with this information.

Start Assist Not Available" message in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) B1262:92 stored in multiple door latch control modules (DCME, DCMF, DCMG, and/or DCMH). DTC U0504 may also be stored in the gearshift module (GSM). This may be due to the software in the door latch control modules. To correct this condition, download and run the following applications using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool.<br /> "DCME - Door Control Module E (DCME) Software Update"<br /> "DCMF - Door Control Module F (DCMF) Software Update"<br /> "DCMG - Door Control Module G (DCMG) Software Update"<br /> "DCMH - Door Control Module H (DCMH) Software Update"<br /> For claiming use causal part 54219A65 and labor operation MT54219SSM up to 0.5 hours.

Start Assist Not Available" message in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) B1262:92 stored in multiple door latch control modules (DCME, DCMF, DCMG, and/or DCMH). DTC U0504 may also be stored in the gearshift module (GSM). This may be due to the software in the door latch control modules. To correct this condition, download and run the following applications using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. "DCME - Door Control Module E (DCME) Software Update" "DCMF - Door Control Module F (DCMF) Software Update" "DCMG - Door Control Module G (DCMG) Software Update" "DCMH - Door Control Module H (DCMH) Software Update" For claiming use causal part 54219A65 and labor operation MT54219SSM up to 0.5 hours.

introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.

Transmission Replacement

U3000:96 stored in the power steering control module (PSCM) after programming the PSCM, or may display the following message in Ford Diagnosis and Repair System (FDRS) when performing PSCM programmable module installation (PMI): <br /><br /> "It has been detected that a Model Year 2025 Steering Gear (R1MC - level) is fitted to this vehicle. It is not possible to run the Power Steering Control Module (PSCM) Programmable Module Installation (PMI) application on this Steering Gear. If later software is available, this PSCM can be updated by running the PSCM Software Update application."<br /><br /> This may be due to the calibration in the PSCM. When installing a replacement steering gear, make sure the part number begins with prefix "S1MZ". If DTC U3000:96 previously set after programming the PSCM, continue with normal diagnostics outside this article. Refer to Workshop Manual (WSM), Section 211-02 > Diagnosis and Testing. Improvements have been made to the diagnostics for this DTC.

r/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.

inner/outer CV joint boot for various reasons. If Workshop Manual (WSM), Section 205-04 > Diagnosis and Testing leads to CV joint boot replacement, L1MZ-3A331-G (Explorer/Police Interceptor Utility front inner/outer CV joint boot kit), L1MZ-3A331-H (Aviator front inner/outer CV joint boot kit), L1MZ-3A331-F (Explorer/Police Interceptor Utility front inner CV joint boot kit) and L1MZ-3A331-E (Aviator front inner CV joint boot kit) have been released for service. Refer to WSM, Section 205-04 for Removal and Installation procedures.

removed from the vehicle in Q1 2026 due to the end of life of Amazon Alexa services in all Ford/Lincoln Digital Experience vehicles. Google Assistant will continue to be the default voice assistant in these vehicles. No additional actions should be taken in an attempt to restore Alexa Built-In functionality.

Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.

Vehicles Equipped with Google Automotive Services (Minor Feature Code HKCGA And IEPAT)

key fob indicating that the vehicle has remote started (or not remote started). Factory key fobs with remote start no longer contain an LED feedback indicator. Do not replace the key fob for this condition. This is a normal operating characteristic and no service action is necessary.

cause a hard brake pedal and some lamps in the cluster. Issue gets resolved in the next key cycle -Addresses key off load battery usage caused by the Electric brake boost staying active"

Navigation System (minor feature code HKCGA) may experience a blank screen for Google Maps or the absence of live traffic data. To correct this condition, refer to the Workshop Manual (WSM), Section 415-00 > Diagnosis and Testing > Information and Entertainment System. The WSM has been updated with improved diagnostics for this condition. To confirm whether a vehicle is built with a specific minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner of the Professional Technician System (PTS).

unexpected Watch the Road warning while using BlueCruise with no diagnostic trouble codes (DTCs) stored related to the driver-assist systems. This may be due to the steering column tilt angle and/or driver seat position (height and backrest angle). Replacing components is not expected to resolve this issue. Optimize driver head position by adjusting the steering column tilt angle and driver seat position (height and backrest angle) to ensure the driver status monitor camera (DSMC) mounted on top of the steering column has a clear view of the drivers entire face from chin to forehead. Provide both Explorer and Aviator customers with a printout of the Lincoln Aviator Owners Manual page titled, Lincoln BlueCruise > How Does BlueCruise Work. The Explorer Owner's Manual is in process of being updated. If the customers symptom persists after the above adjustments have been performed, continue with normal diagnostics found in the Workshop Manual (WSM), Section 419-03B.

mph (55-130 km/h) in the steering wheel and/or seat.

fold, exhibit excess effort to fold, or do not slide forward/backward easily. Power or manual second row seats must be pushed forward manually during easy entry function since the assist spring will reduce but not eliminate manual effort. Refer to the Owner's Manua