2020 Lincoln Aviator TSBs

This may be due to a concern with the front courtesy lamp light module.

Batteries Battery Energy Control Module (BECM) Software Update

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

App Lincoln App including but not limited to: missing activation prompt pop-upon the vehicle's center display screen when attempting to activate vehicle through The Ford App Lincoln App, incorrect location global positioning system GPS reported through The Ford App Lincoln App, problems with remote commands being performed through The Ford App Lincoln App and or incorrect data information reported on The Ford App Lincoln App. These symptoms will be accompanied by diagnostic trouble code DTC B156D 89 in the TCU. This may be due to the accessory protocol interface module APIM software. To correct the condition, update the APIM software.

inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.

Some of the vehicles listed in the model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with only diagnostic trouble code (DTC) P1A0C stored in the PCM. This may be due to the software in the powertrain control module (PCM).

display screen at start-up using Apple CarPlay or Android Auto. This does not affect rear camera operation. This may be due to interference from the phone being connected into the media hub using a universal serial bus (USB) cable during SYNC system boot up. To correct his condition, advise the customer to disconnect the USB cable from the phone. If the center display screen displays normally, reconnect the phone. If the concern persists, disconnect the phone from the USB cable, cycle the ignition off and open the driver's door so the interior lights come on. Close the door, start the vehicle and wait for the center display screen to boot up past the start-up animation and display the home screen, then reconnect the phone using the USB cable. If the concern persists after this procedure, follow normal Workshop Manual diagnostics for a blank screen concern.

vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450:00 stored in the powertrain control module (PCM). This may be due to an evaporative emission system concern or may also be caused by the customer overfilling the fuel tank. If this condition occurs, perform normal diagnosis per Workshop Manual (WSM) Section, 303-13 and repair as necessary. Inform the customer that the condition may have been caused by overfilling of the fuel tank and to not top-off the fuel tank when the fuel pump nozzle automatically shuts off for the first time. Refer the customer to the Fuel and Refueling section of their Owner Manual for additional information.

2024-2025 Nautilus vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450:00 stored in the powertrain control module (PCM). This may be due to an evaporative emission system concern or may also be caused by the customer overfilling the fuel tank. If this condition occurs, perform normal diagnosis per Workshop Manual (WSM) Section, 303-13 and repair as necessary. Inform the customer that the condition may have been caused by overfilling of the fuel tank and to not top-off the fuel tank when the fuel pump nozzle automatically shuts off for the first time. Refer the customer to the Fuel and Refueling section of their Owner Manual for additional information.

buzzing/clicking/humming/ticking sound from the overhead console (OHC) and/or diagnostic trouble code (DTC) P24AE in the heating ventilation and air conditioning (HVAC) module.

toggle button in the Connectivity setting menu grayed out with an inability to switch it off.

the SYNC software, you may experience SYNC system instability concerns and/or a failure to preserve certain settings across ignition cycles. This may result in a black infotainment screen that does not affect rear view camera, incorrect language setting, erased or unsaved radio presets, and potential inability to perform software updates.

concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software

using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt.

using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level

Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.

replacement of the left front halfshaft, part number L1MZ-3A427-G. If the halfshaft is unavailable due to a part backorder situation, dealers can perform Technical Service Bulletin (TSB) 23-2174. The TSB Service Procedure uses a revised halfshaft and intermediate shaft, which eliminates the front axle disconnect actuator assembly and requires an all-wheel-drive (AWD) module software update. Unless the specific TSB criteria are met, TSB 23-2174 should not be performed if halfshaft part number L1MZ-3A427-G is available.

P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking the fuel pump monitor (VE518) and/or a fuel pump control (VE225) circuits, connector pin push-outs, damaged pins/terminals, and/or loose/corroded grounds. Inspect FPCM connector C433/C4033, ground G407, and inline connections C1147 and C3136 for being fully seated and damage free prior to performing guided diagnostics or replacing any components.

panel cluster (IPC) and/or audio front control module (ACM). This DTC will not cause observable conditions or warning indicators for the customer. If this DTC is detected during pre-delivery inspection (PDI) or while diagnosing unrelated conditions, it should be disregarded.

buzzing/clicking/humming/ticking sound from the OHC and/or diagnostic trouble code (DTC) P24AE in the heating ventilation and air conditioning (HVAC) module. To confirm if a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). If diagnostics lead to the in-vehicle temperature and humidity sensor as the causal part, a new lower level part is available. It is not necessary to replace the OHC assembly if only the sensor is suspect. Use part number L1MZ-19F666-A to resolve the concern.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

replacement of the left front halfshaft, part number L1MZ-3A427-G. If the halfshaft is unavailable due to a part backorder situation, dealers can perform Technical Service Bulletin (TSB) 23-2174. The TSB Service Procedure uses a revised halfshaft and intermediate shaft, which eliminates the front axle disconnect actuator assembly and requires an all-wheel-drive (AWD) module software update. Unless the specific TSB criteria are met, TSB 23-2174 should not be performed if halfshaft part number L1MZ-3A427-G is available.

turn signals and streaming audio over Bluetooth. Customers may describe static heard during a Bluetooth phone call or a door speaker buzz or tick noise with the pulse of the turn signal. This may be due to concerns with the 14401/14A005 wiring harnesses or connector damage. Prior to the replacement of the affected speaker, inspect for incorrect pin fit/crimp, bent pins, broken wire strands, or other damage at inline connectors C202, C2383A, and/or C4240B. These circuits join the accessory protocol interface module (APIM) and audio front control module (ACM) components. If wiring/connector concerns are found, repair per Wiring Diagram Cell 5.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software.

This may be due to the SYNC module (APIM) software. Download and run the APIM-SYNC Module (APIM) Standard Programming application using the latest software level of the Ford Diagnosis and Repair System (FDRS). After programming the APIM to the latest level, the EV power flow screen may intermittently not function under certain conditions. No further repair procedure is recommended as this function is not critical to the operation of the hybrid powertrain system. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.

replacement of the left front halfshaft, part number L1MZ-3A427-G. If the halfshaft is unavailable due to a part backorder situation, dealers can perform Technical Service Bulletin (TSB) 23-2174. The TSB Service Procedure uses a revised halfshaft and intermediate shaft, which eliminates the front axle disconnect actuator assembly and requires an all-wheel-drive (AWD) module software update. Unless the specific TSB criteria are met, TSB 23-2174 should not be performed if halfshaft part number L1MZ-3A427-G is available.

turn signals and streaming audio over Bluetooth. Customers may describe static heard during a Bluetooth phone call, or a door speaker buzz or tick noise with the pulse of the turn signal. This may be due to concerns with the 14401/14A005 wiring harnesses or connector damage. Prior to the replacement of the affected speaker, inspect for incorrect pin fit/crimp, bent pins, broken wire strands, or other damage at inline connectors C202, C2383A, and/or C4240B. These circuits join the SYNC module (APIM) and audio front control module (ACM) components. If wiring/connector concerns are found, repair per Wiring Diagram Cell 5.

replacement of the left front halfshaft, part number L1MZ-3A427-G. If the halfshaft is unavailable due to a part backorder situation, dealers can perform Technical Service Bulletin (TSB) 23-2114. The TSB Service Procedure uses a revised halfshaft and intermediate shaft, which eliminates the front axle disconnect actuator assembly and requires an all-wheel-drive (AWD) module software update. Unless the specific TSB criteria are met, TSB 23-2144 should not be performed if halfshaft part number L1MZ-3A427-G is available.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

lamp (MIL) and powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) B108A:01 (general electrical failure), B108A:24 (signal stuck high), and/or B108A:9E (stuck on). The ignition mode light emitting diode (LED) indicator may also flash quickly. This condition may be caused by loose wiring terminal crimps on connector C2195 at the push button ignition switch. Examine Pin 1 (CPK34/Gn) first, since it is the only pin with the smallest (26 gauge) wire. To correct this condition, repair terminal crimps per Wiring Diagram (WD) Cell 5. If no wiring terminal faults are found, refer to Workshop Manual (WSM) Section 211-05 for normal diagnostics. The push button ignition switch pinpoint tests in the WSM have been updated.

FordPass/LincolnWay app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the WSM. Test the function of the A/C to verify that it is blowing cold air.

diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer  G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2D40. This may be due to the high voltage battery thermal system not cooling as it should. Follow the updated WSM Section 414-03 including listed possible sources, visual inspection and prechecks, and diagnostic procedures.

Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Also, ambient lighting may be inoperative or always on. If this concern occurs, check the center console cup holder area for evidence of liquid intrusion first. Liquid can short the local interconnect network (LIN) circuit. Temporarily disconnect the console inline connector(s) during diagnosis to isolate circuit shorts. Search Wiring Diagram (WD) for *cup holder ambient* to display the related connectors. If a short is found in cup holder ambient light ring light emitting diode (LED) connector, repair as necessary. If no evidence of liquid intrusion is found, continue with normal Workshop Manual (WSM) diagnostics.

features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

illuminated MIL with diagnostic trouble code (DTC) P2D40. This may be due to the chiller not interpreting the correct cooling value of the high voltage battery chiller. To correct the condition, follow the Service Procedure to diagnose the cause of the incorrect value.

discharged while the vehicle is plugged in during high voltage battery charging and/or inoperative level 2 charger (220/240 volts) at customers residence but charging performance operates as intended at a dealership or other locations. This may be due to the software in the battery charger control module (BCCM) (also known as secondary on-board diagnostic module SOBDM). To correct the condition, follow the Service Procedure to reprogram various modules starting with the PCM.

This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.

diagnostic trouble codes (DTCs) B1175:19, B1176:19, B11C0:19 and/or B11C1:19 present in door latch control module E (DCME), door latch control module F (DCMF), door latch control module G (DCMG) and/or door latch control module H (DCMH). This may be due to low battery voltage and DTC thresholds being too low and not a fault in the door latch assembly. To correct the condition, reprogram and re-configure the the affected module using the latest level of the Ford Diagnosis and Repair System (FDRS). For claiming use causal part 54264A27 and applicable labor times found in Section 10 of the Service Labor Time Standards (SLTS) Manual.

message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTCs) B1041 and U2100 stored in the SUMA. This may be due to the SUMA entering into a diagnostic service mode after an on-demand self-test or module replacement. If no other DTCs are present, use the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool to update and configure the SUMA. If other DTCs are present, refer to Workshop Manual (WSM), Section 204-05 for normal diagnostics. For claiming use causal part 5319 and applicable labor times found in Section 10 of the Service Labor Time Standards (SLTS) Manual.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.

exhibit Phone-as-a-Key concerns and have diagnostic trouble code(s) (DTC) U200D:15, U200E:15, U200F:15, B15**:31, B15**:49 and/or B15A5:56 stored in the remote function actuator (RFA) module. If the vehicle is exhibiting other symptoms outside of Phone-as-a-key concerns, address those first. If any of these DTCs are detected during diagnostics, clear the DTCs, reflash RFA to the latest software level and start a new Ford Diagnosis and Repair System (FDRS) session. Verify that DTCs are no longer present. If only the B15**:31, B15**:57 and/or B15A5:56 DTC(s) returns in the RFA after a self test, follow normal Workshop Manual (WSM) diagnostics, Section 419-01C.

diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer  G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the WSM. Test the function of the A/C to verify that it is blowing cold air.

features such as the hands free liftgate or when using the outside control button on the liftgate handle when the doors are locked. This may be due to a poor wiring connection at connector C4332 for the rear keyless entry antenna. If these symptoms are present, inspect C4332 (below the liftgate striker) for a poor connection, loose terminals, or improper pin-fit.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

diagnostic trouble code (DTC) B1404:13 and/or B1407:13. This may be due to contamination and relative movement in the connection between the wiring harness and the side airbag. To correct the condition, follow the Service Procedure to replace the affected connector with a service pigtail and the affected side airbag.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Diagnostic Trouble Codes (DTCs) P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2022 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

instrument panel cluster (IPC) that does not correctly represent the actual fuel level of the vehicle. This may be due to excessive idling and/or a learned value in the powertrain control module (PCM) that is incorrect. To correct the condition, perform the PCM - Reset the Keep Alive Memory (KAM) application in the appropriate Ford diagnostic scan tool. For claiming, use Causal Part 12A650 and applicable labor times from Section 10 in the Service Labor Time Standards (SLTS) Manual.

FordPass or LincolnWay App message notification indicating deep sleep mode and connectivity is temporarily unavailable while the vehicle is plugged in during high voltage battery charging. The vehicle may also exhibit an inoperative remote start feature and/or lock and unlock functionality. This may be due to the software in the telematics control unit (TCU). To correct this condition, follow the Service Procedure to reprogram the TCU.

inoperative driver door window control switch (windows inoperative, mirror control unresponsive, etc.). Diagnostic trouble code (DTC) B1088:87 may be present in the driver door module (DDM). This may be due to the software in the DDM. To correct the condition, reprogram the DDM with the latest software level of the Ford Diagnosis and Repair System (FDRS). After reprogramming the DDM, run the DDM configuration application and perform a window learn routine via FDRS. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Fault, and/or Collison Warning Not Available message with various diagnostic trouble codes (DTC) stored in the image processing module A (IPMA). If programming fails or Ford Diagnosis and Repair System (FDRS) states a file failed to flash after replacing the IPMA or reprogramming IPMA software, test the battery using any approved Rotunda tool including the GR-190, GRX-3590, and DCA-8000. Fully recharge or replace the battery according to results of the tool. Set the battery charger to maintain battery voltage between 12.6 and 13.6 volts during the entire programming procedure. The IPMA programming procedure may take several hours to complete due to the size of the software files required.

This may be due to concerns with the wiring harness or connections of connector C2383A, C202, and/or C4240B. Prior to the replacement of the affected speaker, inspect the inline connections at connectors C2383A, C202, and C4240B for damage or incorrect pin fit. If no concerns are found with the wiring harness, continue with the replacement of the affected speaker.

These DTCs may include P04F0, P008A, P0451, P0455, P0456, P0496 and/or P018C. This may be due to the wiring harness connection at connector C1198. Prior to replacement of any components, inspect the connector and wiring harness for any damage or pin fit concerns. If any damage or pin fit concerns are found, repair the connector or harness as necessary. If no damage or pin fit concerns are found, refer to normal diagnostics.

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

Use a 110/120V non-GFI outlet and check to see if the vehicle charges properly with the 220V adapter removed. If the charging cord concern is only present when using the 220V adapter, a complete charge cord replacement may not be needed as the 220V adapter (part number VL5CZ-10B706-B) is available separately at accessories.lincoln.com or through the local Ford Authorized Distributor (FAD). Note that discoloration of the 220V adapter or dual voltage charging cord could indicate a problem with the electrical outlet that's used and should be inspected by a licensed electrician. For further diagnostic assistance, contact Webasto Charging systems, Inc. directly at 888-219-6747 or at evscs@webasto.com.

This may be due to the software in the accessory protocol interface module (APIM) SYNC module. Download and run the APIM Configuration application in the Ford Diagnostic and Repair System (FDRS) scan tool. If asked if the original module is still installed, answer NO. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

diagnostic trouble code (DTC) B1404:13 and/or B1407:13. This may be due to contamination and relative movement in the connection between the wiring harness and the side airbag. To correct the condition, follow the Service Procedure steps to replace the affected connector with a service pigtail and the affected side airbag.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.

may exhibit a no-start with a Stop Safely Now warning message in the instrument panel cluster (IPC). The vehicle may have one or more of the following DTCs P0A23, P0A6F, P0A72, P0A75, P0A71, P0A74, P0A77, P0DFA, P06B1, P0A47, P1A0E set by the secondary on-board diagnostic module C (SOBDMC) or secondary on-board diagnostic module B (SOBDMB). This may be due to a drop in the 12-volt circuit. These DTCs will often occur at vehicle key-on and may be difficult to reproduce. Before replacement of the SOBDMC or SOBDMB, diagnose any low voltage DTCs (P0562, U3003) in other modules in the 12V system. If low voltage (less than 10V) is observed in these DTCs snapshot, diagnose the 12v system first. Refer to Workshop Manual (WSM), Section 418-00.

ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the Shop manual. Test the function of the A/C to ensure that it is blowing cold air.

Phone-as-a-Key concerns and have diagnostic trouble code(s) (DTC) U200D:15, U200E:15, U200F:15, B15**:31, B15**:49 and/or B15A5:56 stored in the remote function actuator (RFA) module. If the vehicle is exhibiting other symptoms outside of Phone-as-a-key concerns, address those first. If any of these DTCs are detected during diagnostics, clear the DTCs, reflash RFA to the latest software level and start a new Ford Diagnosis and Repair System (FDRS) session. Verify that DTCs are no longer present. If only the B15**:31, B15**:57 and/or B15A5:56 DTC(s) returns in the RFA after a self test, follow normal Workshop Manual (WSM) diagnostics, Section 419-01C.

remote function actuator (RFA) module preventing paring-connecting any phone as a key to the vehicle. If this DTC is detected during pre-delivery inspection (PDI) or while diagnosing phone as a key pare/connection issue, remove the RFA fuse or disconnect the battery terminals for minimum of 5 minutes then reinstall. Start a new FDRS session and verify that U3000:49 is no longer present. Ensure that phone as a key is enabled and a phone can be paired to the vehicle. If the concern is still present, follow normal diagnostics procedures in Workshop Manual (WSM), Section 419-01C.

symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

20-Mar-2020 may exhibit various warning/fault messages with diagnostic trouble codes (DTCs) C0633 and/or C00A6:07 stored in the AWD module. This may be caused by an oil contaminated front halfshaft speed sensor. To correct the condition, follow the Service Procedure step to replace the front halfshaft speed sensor.

display for one or more cameras when the 360 degree camera view is activated. To correct the condition, reprogram the image processing module B (IPMB) using the latest software level of the appropriate Ford diagnostic scan tool. Once complete, perform the 360 degree camera alignment procedure. Refer to Workshop Manual (WSM), Section 413-13. For claiming, use causal part 19H405 and applicable labor operations in the Service Labor Time Standards (SLTS) Manual.

have diagnostic trouble code(s) (DTC) U200D:15, U200E:15, U200F:15, B15**:31, B15**:49 and/or B15A5:56 stored in the remote function actuator (RFA) module. If any of these DTCs are detected during normal diagnostics, clear the DTCs, reflash RFA to the latest software level and start a new Ford Diagnosis and Repair System (FDRS) session. Verify that DTCs are no longer present. If only the B15**:31, B15**:57 and/or B15A5:56 DTC(s) returns in the RFA after a self test, follow normal Workshop Manual (WSM) diagnostics, Section 419-01C.

front seat moving forward during easy entry/exit operation when the vehicle is turned off. This may be due to the software in the driver front seat module (DSM). To correct the condition, replace the DSM and reprogram the DSM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14C708 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.

an SSM or TSB is published for a software update. This may be due to the module already being at the latest software level. A later software level may have been programmed at the assembly plant, during a previous dealer visit or by an over the air (OTA) update for vehicles that have automatic updates enabled in the SYNC system settings. To review a vehicle's OTA update history, visit the Connected Vehicle > OTA Dashboard tab in OASIS. Information about the OTA Dashboard can be found on FMCDealer.com when performing a search on OTA History Job Aid.

Connected' or 'Trailer Disconnected' message in the vehicle's message center with no trailer attached to the vehicle. To address this condition, reprogram the trailer module (TRM) using the appropriate Ford diagnostic scan tool. For claiming use causal part 19H332 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Escape/Explorer/SuperDuty/Transit/Aviator/Corsair, 2021 Bronco Sport/F-150/Mustang/Mach-E the Workshop Manual (WSM) diagnostics may direct to replace a module on vehicles that use Ford Diagnosis and Repair System (FDRS). First, an FDRS session must be created on the vehicle prior to removing the faulted module. Once the session is started, run the Programmable Module Installation and replace the module only when instructed by FDRS. Installing a new module prior to starting a scan tool session may result in incomplete module configuration with DTCs U2100, U2101 and/or U2200. Once a session has been started, continue to follow normal WSM procedures to repair the vehicle.

inoperative remote start, and/or an illuminated wrench light with diagnostic trouble codes (DTCs) P07E4, B135C and/or U0103. This may be due to a loose ground G210 and/or G214. Check grounds G210 and G214, refer to the Wiring Diagram for location information. If the concern persists, or the grounds are found to be secure, refer to the Workshop Manual and applicable sections of the Powertrain Controls/Emissions Diagnosis (PC/ED) Manual for normal diagnostics.

DTC P025A And/Or DTC U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds(F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2021 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2021 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

open 3 or 4 post fuse array on the high current battery junction box (BJB). Service part LU5Z-14526-ALD has been released for the 3 post fuse array and LU5Z-14526-ANC has been released for the 4 post fuse array. It is no longer necessary to order the complete wiring harness to obtain these parts.

folding with diagnostic trouble codes (DTCs) B1231:54 and/or B1232:54 stored in the power fold seat module (SCMJ). This may be due to the software in the SCMJ. To correct the condition, connect a battery charger and reprogram the SCMJ using the latest software level of the appropriate Ford diagnostic scan tool. Then open the liftgate, and perform the SCMJ - Power Fold Seat Module (SCMJ) Learn Seat Procedure. For claiming, use causal part 14F042 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

exhibit an intermittent blank or blue screen when placed into reverse but return to normal when placed into drive. This condition may be more noticeable during cool or colder temperatures. To correct the condition, reprogram the image processing module B (IPMB) using the latest software version of the appropriate Ford scan tool. For claiming, use causal part 19H405 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

an illuminated wrench light with diagnostic trouble codes (DTCs) P07E4, B135C and/or U0103. This may be due to a loose ground G210 and/or G214. Check grounds G210 and G214, refer to the Wiring Diagram for location information. If the concern persists, or the grounds are found to be secure, refer to the Workshop Manual and applicable sections of the Powertrain Controls/Emissions Diagnosis (PC/ED) Manual for normal diagnostics.

with diagnostic trouble code (DTC) U3012 stored in the battery energy control module (BECM) after charging the high voltage battery with an electric vehicle supply equipment (EVSE) cord and/or DTC P0D5C stored in the secondary on-board diagnostic control module A (SOBDM). This may be due to the software in the SOBDM. To correct the condition, reprogram the SOBDM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 10B689 and applicable labor operation in Section 10 of the Service Labor Time Standards (SLTS) Manual.

in the IPC and/or exhibit a steering wheel offset from the straight ahead position without any related diagnostic trouble codes (DTCs) stored. This may be caused by the software in the steering effort control module (SECM) and the steering angle sensor module (SASM). To correct the condition, reprogram the SECM and SASM using the latest level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 3600 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0C48, P0C49, P2B29, P0CFF, P0E1F, P0C4B, P0C4A, P2CF3, P0A06, P0A07, P2D01, P2D00, P2D03, P2D04, P0C73, and/or P2D02 stored in the powertrain control module (PCM). This may be due to the software in the battery energy control module (BECM). To correct the condition, follow the Service Procedure to reprogram the BECM.

blank/black screen on the center infotainment display due the low voltage differential signaling (LVDS) cable at the SYNC accessory protocol interface module (APIM) not being fully seated. Verify that the connector is fully seated into the APIM prior to performing any other diagnostics or repairs on the vehicle for this concern. If the connection is found loose, re-seat the connection and retest.

or 4 post fuse array on the high current battery junction box (BJB). Service part LU5Z-14526-ALD has been released for the 3 post fuse array and LU5Z-14526-ANC has been released for the 4 post fuse array. It is no longer necessary to order the complete wiring harness to obtain these parts.

panel cluster (IPC) that does not correctly represent the actual fuel level of the vehicle. This may be due to excessive idling and/or a learned value in the powertrain control module (PCM) that is incorrect. To correct the condition, perform the PCM - Reset the Keep Alive Memory (KAM) application in the appropriate Ford diagnostic scan tool. For claiming, use Causal Part 12A650 and applicable labor times from Section 10 in the Service Labor Time Standards (SLTS) Manual.

presets and/or preset pages may be inaccurate in the front display interface module (FDIM). This may be due to the software in the accessory protocol interface module (APIM) SYNC module. To correct the condition, download and run the APIM Configuration application in the Ford Diagnostic and Repair System (FDRS) scan tool. If asked if the original module is still installed, answer NO. The SYNC 3 universal thumb drive should not be used to correct this condition. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

pop-up on the SYNC infotainment system, vehicle connectivity concerns, vehicle location disabled message and/or various FordPass/LincolnWay App command/control concerns. To correct these conditions, ensure that customer connectivity settings (CCS) are turned on in the SYNC system. If the concerns persist after CCS is turned on, turn CCS OFF, perform an ignition cycle, and turn CCS settings back on. After any CCS changes, force-close and relaunch the FordPass/ LincolnWay app on the customers phone. Once CCS is turned on, program the TCU to the latest IDS/FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

This may be due to the current level SYNC software installed. To correct this condition, program the SYNC module. Refer to Workshop Manual (WSM), Section 415-00. If no update is available or the condition persists after programming, refer to WSM, Section 303-06 for further diagnosis. The remote start can be disabled in one of three methods: (1) leaving the hood open, (2) de-activation through the SYNC System Customer Preferences (refer to SYNC settings in the Owner's Manual), or (3) disconnecting the 12 Volt Battery. Refer to WSM, Section 100-00 for further information on remote start disabling.

starting the vehicle using remote start. The heated/cooled seats and/or heated steering wheel may not turn on when previously set to on/auto. This may be due to software in the heating, ventilation, and air conditioning (HVAC) control module. To correct this condition, reprogram the HVAC control module to the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 18C612 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

front seat moving forward during easy entry/exit operation when the vehicle is turned off. This may be due to the software in the driver front seat module (DSM). To correct the condition, reprogram the DSM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14C708 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

power liftgate and/or false activation of the anti-theft alarm with diagnostic trouble codes (DTCs) B144D, B144E, B1555 and/or B1556 stored in the rear gate trunk module (RGTM). This may be due to the software in the RGTM improperly sensing that the liftgate is ajar. To correct the condition, reprogram the RGTM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Camera Fault message and/or Collision Warning Not Available message with diagnostic trouble code (DTC) U3000:49 stored in the image processing module A (IPMA). This may be due to the software in the IPMA. To correct the condition, reprogram the IPMA using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.

12-Mar-2020 may exhibit a discharged battery/no crank condition. This may be due to a parasitic battery draw caused by software in the rear audio control module (RACM). To correct the condition, reprogram the RACM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 18E261 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

This DTC will not cause observable conditions or warning indicators for the customer. If this DTC is detected during pre-delivery inspection (PDI) or while diagnosing unrelated conditions, it should be disregarded.

infotainment display due the low voltage differential signaling (LVDS) cable at the SYNC accessory protocol interface module (APIM) not being fully seated. Verify that the connector is fully seated into the APIM prior to performing any other diagnostics or repairs on the vehicle for this concern. If the connection is found loose, re-seat the connection and retest. If the LVDS cable is found not to be the cause of the blank screen, follow Workshop Manual section 415-00 for further diagnosis. For claiming, use causal part number 10E929 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Warning Not Available message with diagnostic trouble code (DTC) U3000:49 stored in the image processing module A (IPMA). This may be due to the software in the IPMA. To correct the condition, reprogram the IPMA using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

start event using the Fordpass or Lincolnway app. This may be due to the current level SYNC software installed. To correct this condition, program the SYNC module utilizing section 415 of the workshop manual. If no update is available or the problem persists after programming, verify that the Fordpass or Lincolnway app is activated properly as per the owners guide. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

2016-2018 MKX, 2019-2020 Nautilus, 2020 Aviator/Corsair and 2013-2020 MKZ vehicles equipped with multi-contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.

the front engine cover removed and reinstalled for various reasons. The Workshop Manual (WSM), Section 303-01 Engine > Removal and Installation > Engine Front Cover service procedure has been updated to include a new essential special service tool (ESST) guide pin alignment tool (303-1790) that is used to align the engine front cover to the engine block, preventing the O-ring seal on the engine oil galley feed tube from getting damaged during installation.

> Front Seats > Diagnosis and Testing lead to the replacement of the front seat cushion extension adjuster, a lower-level part is now available (14C720). It is not necessary to replace the front seat cushion extension adjuster if only the front seat cushion extension motor assembly is damaged. For Corsair, use service part LJ7Z-14C720-A. For Aviator, use service part R2TZ-14C720-A. For 2025-2026 Navigator (both sides) and 2018-2024 Navigator driver side, use service part NL7Z-14C720-A. For 2018-2024 Navigator passenger side, use service part NL7Z-14C720-B.

smoke on startup for the first 5 minutes after an overnight cold soak with no illuminated malfunction indicator lamp (MIL) or powertrain diagnostic trouble codes (DTCs) present. This may be due to engine oil breaching the dynamic oil seals separating the bearing core from the turbine housing in the left side turbocharger assembly. There is a new, updated left side turbocharger oil supply tube equipped with an internal check valve to prevent the engine oil from entering turbine housing after the engine is off. Replace the existing left side turbocharger oil supply tube with the updated service part that includes the check valve (service part# L1MZ-9T516-B) or latest level part. Refer to the Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger > Removal and Installation > Turbocharger Oil Supply Tube LH. For claiming, use causal part 9T516 and labor operation code 9440AL.

Reason for update: update the labor operation numbers to add MT to operations C, F, G, H, J, K, L and M, and correct the part number LIMZ-4A015-B to L1MZ-4A015-B. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:  Harsh engagement  Delayed engagement  Harsh shift  Delayed shift  Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC)s P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as ne

hybrid engine, and 2020-2023 Lincoln Aviator vehicles equipped with a 3.0L EcoBoost hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the belt integrated starter generator (BISG). For vehicles with this condition, follow the necessary Pinpoint Test in Workshop Manual (WSM), Section 303-06 for DTC P0A1E and repair the vehicle as directed. Note that previous replacement of the BISG does not negate the need for subsequent BISG replacements if directed to do so by the appropriate Pinpoint Test diagnostics. Engineering is investigating this BISG quality concern. Monitor PTS for updates regarding this investigation.

and 2023 Explorer Vehicles Front Windshield Wiper Motor Replacement, if Required After Dealer Evaluation

Reason for update: update the labor time allowance for F-150 vehicles, update the Parts list to replace the part number W716979-S439 with W721084-S439, and add a note for LV fluids XT-10-QLVC and CXT-10-LV6 "Transfer Case Fluid". Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:  Harsh engagement  Delayed engagement  Harsh shift  Delayed shift  Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC)s P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other tra

vehicles equipped with a 3.0/3.3L engine may require various repairs associated with the fuel tank and/or fuel pump and sender unit. Workshop Manual (WSM), Section 310-00 > Removal and Installation for the fuel tank and fuel pump and sender unit have been revised to eliminate the need to remove the driveshaft as part of the service procedure. Labor times have also been updated to reflect this WSM revision.

in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.

or 3.0L plug-in hybrid electric vehicle (PHEV) engine, 2020 Explorer vehicles equipped with a 3.0L EcoBoost, and 2020 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine. This noise may occur on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to an internal component of the variable cam timing (VCT) unit. If diagnostics lead to the VCTs as the source of the noise, refer to the 2024 F-150 Workshop Manual (WSM), Section 303-00 > Diagnosis and Testing > Engine > Pinpoint Test F. Pinpoint test F has been updated to include additional steps along with a video on how to identify the single affected VCT unit that requires replacement.

Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:  Harsh engagement  Delayed engagement  Harsh shift  Delayed shift  Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC)s P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary as needed to ensure proper function. Add a new line to the repair order to docum

Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.

turbocharger oil supply tube due to various concerns.

noise at idle and/or while driving.

Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs.

vehicles equipped with a 2.7L EcoBoost or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.

harsh/delayed engagements and/or harsh/delayed shifts, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.

Some 2021-2023 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.

Some 2021-2022 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

The 2023 F-150 10R80 and 10R80 MHT vehicles will be the subject of a separate article. Some 2021-2022 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

Some 2020-2023 Explorer vehicles equipped with a 3.0L EcoBoost engine or 2020-2023 Aviator vehicles equipped with a 3.0L EcoBoost or 3.0L PHEV engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn VCT unit. To correct the condition, follow the Service Procedure to replace the VCT units

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

malfunction (wrench) indicator and/or 4WD Fault Service Required message with diagnostic trouble codes (DTCs) C00A6:71, C00A6:74, C00A6:99, C00A7:11, C00A7:13, C00A8:11, and/or C00A8:13 present in the AWD module. This may be due to a damaged wiring harness rubbing against the underbody heat shield where it routes over and into the transfer case actuator motor. Inspect the wire harness for damage and repair as necessary following the procedures in the Wiring Diagram Manual. If no damage is found, continue with normal diagnostics.

harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy and/or sticking valves in the main control valve body. To correct the condition, follow the Service Procedure to identify and correct the condition.

vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes. stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost hybrid engine, 2020-2023 Explorer vehicles equipped with a 3.3L hybrid engine and 2020-2023 Aviator vehicles equipped with a 3.0L hybrid engine may exhibit a powertrain malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). This may be due to the belt integrated starter generator (BISG). To correct this condition, follow the Service Procedure to diagnose and repair this symptom.

Some 2018-2021 Expedition/Navigator and 2020-2021 Explorer/Aviator vehicles equipped with a 10R80/10R80 MHT or 10R60 (excluding Police Interceptor vehicles with column shift) may exhibit a momentary transmission neutral-out condition while in drive. Vehicle may also have diagnostic trouble code (DTC) P07E6 and/or P07E4 stored in the powertrain control module (PCM) or transmission control module (TCM) and/or a possible audible noise. This may be due to a leak in the park valve circuit. To correct the condition, follow the Service Procedure to inspect the park system hardware for wear or damage and replace the valve body separator plate with an improved valve body separator plate.

noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report if there is a customer concern of whine noise describing operating conditions and noise severity.

hybrid engine and 2020-2023 Aviator vehicles equipped with a 3.0L hybrid engine may exhibit a powertrain malfunction indicator lamp with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). This may be due to the belt integrated starter generator (BISG). To correct this condition, follow the Service Procedure to diagnose and repair this symptom.

non-hybrid vehicles equipped with a 3.0L EcoBoost engine built on or before 01-Jan-2023 may exhibit an exhaust rattle requiring replacement of the left or right exhaust flexible pipe (5G203). The updated part locates the flexible joint portion of the pipe closer toward the catalytic converter than the originally equipped part. This is due to a design change with these replacement components which will not cause any functional issues with the vehicle.

Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60/10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.

non-hybrid vehicles equipped with a 3.0L EcoBoost engine may exhibit an exhaust rattle requiring replacement of the left or right exhaust flexible pipe (5G203). The updated part locates the flexible joint portion of the pipe closer toward the catalytic converter than the originally equipped part. This is due to a design change with these replacement components which will not cause any functional issues with the vehicle.

malfunction (wrench) indicator and stop safely now warning. Diagnostic trouble code (DTC) P0AA6:00 may be stored in the battery energy control module (BECM). Inspect the right side frame rail area near the bank 1 charge air cooler (CAC) intake pipe clamp for chafing the orange high voltage harness. If the harness is damaged, de-energize high voltage system per Workshop Manual (WSM), Section 414-03A. Reposition the clamp and replace the high voltage harness (14290). If the harness is not damaged continue P0AA6 diagnostics in WSM, Section 414-03A, Pinpoint Test T. For a P0AA6 diagnostic aid video, refer to Professional Technician System (PTS) > Home > Technical Assistance > Technical Support Videos > enter P0AA6 in search box and click video returned.

For any missing labor operations, claim available new model labor operations or m-time. Refer to this article on the repair order. When replacing the CDF cylinder, the current TSB does not require a complete transmission overhaul or cooler and converter flushing. Ford is currently reviewing the TSB. Monitor OASIS for updates.

noise coming from the left cylinder head. This condition is most noticeable at idle and may lessen at higher engine speed or while driving. This condition does not affect vehicle durability and will not get worse over time. Use a stethoscope or chassis ears and listen just behind the left cylinder head intake VCT solenoid on the cam cover to determine if the thump/knock noise is coming from the cylinder head/camshaft. The left cylinder head and the camshaft roller followers are available as service parts.

2021-2023 Bronco vehicles equipped with a 10R60 transmission and built on or before 23-Dec-2022 or with a 18R80/10R80MHT transmission and built on or before 15-Aug-2022 may exhibit a harsh/delayed engagement and/or harsh/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the PCM or TCM, the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.

exhibit a momentary transmission neutral-out condition while in drive. Vehicle may also have diagnostic trouble code (DTC) P07E6 and/or P07E4 stored in the powertrain control module (PCM) or transmission control module (TCM) and/or a possible audible noise. This may be due to a leak in the park valve circuit. To correct the condition, follow the Service Procedure to inspect the park system hardware for wear or damage and replace the valve body separator plate with an improved valve body separator plate.

Ford is in the process of updating TSB 23-2114. Explorer or Aviator with 3.0L EcoBoost or 3.0L PHEV engine require new sub frame bolts and a steering shaft pinch bolt. Aviator will also require suspension nuts and bolts missing from the TSB that are related to halfshaft removal and installation. To complete the repair, follow Workshop Manual (WSM) Section 205-03 > Front Axle Disconnect Actuator (use the 2020 WSM for 2021 Aviator as the procedure for 2021 is currently being updated). Complete the wiring modification per TSB 23-2114. For Explorer 3.0L EcoBoost vehicles, claim operation 232114E  7.2 hours. For Aviator 3.0L EcoBoost and 3.0L PHEV vehicles, claim operation 232114F  7.8 hours. Refer to this article on the repair order.

F-250/F-350 Super Duty vehicles may exhibit harsh/delayed engagement and/or harsh/delayed shift concerns. These may be addressed with the powertrain control module (PCM)/transmission control module (TCM) Transmission Accelerated Main Control Break In Routine and/or a main control overhaul. Refer to Workshop Manual (WSM), Section 307-01, DTC Chart if DTCs are present and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. Cycling the shift solenoids and clutch control valves to remove contamination must be performed along with an adaptive drive cycle before attempting repair. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) Manual.

noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability.

New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.

type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.

Replacement or reprogramming of the accessory protocol interface module (APIM) will not resolve this condition. Inform customers that engineering is currently working on a solution for this condition and will be released via an over the air (OTA) software update expected in December 2022. Software will update automatically if the vehicle is connected to FordPass/LincolnWay. Monitor OASIS for additional information. Schedule a service appointment for customers that are not connected to FordPass/LincolnWay once the repair becomes available.

Replacement or reprogramming of the accessory protocol interface module (APIM) will not resolve this condition. Inform customers that engineering is currently working on a solution for this condition and will be released via an over the air (OTA) software update expected in December 2022. Software will update automatically if the vehicle is connected to FordPass/LincolnWay. Monitor OASIS for additional information. Schedule a service appointment for customers that are not connected to FordPass/LincolnWay once the repair becomes available.

cooling system due to the transmission cooler. If the cooling system becomes contaminated with ATF, the system must be flushed clear of the contamination after the source of the contamination has been repaired. It is generally not necessary to replace the following components due to ATF contamination in the cooling system: radiator, heater core, de-gas bottle, water pump, auxiliary water pump, coolant control valves, temperature sensors, thermostat, turbocharger, heat exchangers, tubes, gaskets/O-rings/seals (unless removed), or rubber coolant hoses (unless swollen).

This may result in a noise, smell, or leak noticed by the customer. Inspect the rear of the vehicle for signs of rear differential fluid venting in the right rear wheel well (oil staining in the wheel well liner and/or oil residue on the wheel end assembly below) or leaking from the rear differential. If signs of fluid leaks are found from any seals, repair as necessary. Refer to Workshop Manual (WSM), Section 205-02. If no seal leaks are found but fluid is venting, drain the rear differential and re-fill with fresh rear differential fluid. Remove the vent tube and use compressed air to verify that the fluid vent tube is clear. Reinstall the vent tube. Engineering is investigating, monitor OASIS for updates.

exhibit a momentary transmission neutral-out condition while in drive. Vehicle may also have diagnostic trouble code (DTC) P07E6 and/or P07E4 stored in the powertrain control module (PCM) or transmission control module (TCM) and/or a possible audible noise. This may be due to a leak in the park valve circuit. To correct the condition, follow the Service Procedure to inspect the park system hardware for wear or damage and replace the valve body separator plate with an improved valve body separator plate.

This may be due to accessory protocol interface module (APIM) software. Inform customers that engineering is currently working on a solution for this condition and will be released via an over the air (OTA) software update expected in July 2023. Software will update automatically if the vehicle is connected to LincolnWay. Monitor OASIS for additional information. Schedule a service appointment for customers that are not connected to LincolnWay once the repair becomes available.

This may be due to the software in the power fold seat module (SCMJ). To correct the condition, connect a battery charger and reprogram the SCMJ using the latest software level of the appropriate Ford diagnostic scan tool. After reprogramming the SCMJ, perform a manual re-learn procedure. With the engine running, tailgate open, and no objects in the third row seats, press and hold the both seat fold button for one minute until both seats completely fold and unfold. Refer to Owner's Manual for information. Verify that each seat operates correctly after the relearn procedure by pressing the left and then the right third row seat fold buttons. For claiming, use causal part 14F042 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

If during the preliminary inspection the transmission fluid is found to be a foamy pink color this may indicate possible cross contamination of engine coolant and transmission fluid due to an internally leaking transmission fluid cooler assembly. When repairing or replacing the transmission assembly for an internally leaking transmission fluid cooler assembly, use causal part 7869 and applicable labor operations in Section 07 of the Service Labor Time Standards (SLTS) Manual.

exhibit a harsh engagement/harsh shift/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or overhaul main control valve body.

This may be due to the software in the battery energy control module (BECM). The condition occurs when the vehicle is started when the charging cord is connected. To prevent the condition from occurring, disconnect the charger prior to starting the vehicle. If the charger is not disconnected before starting, the ignition will need to be cycled before driving. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in May-2022. No additional diagnosis or service is required for this condition at this time. Monitor OASIS for updates and schedule a service appointment for customers once the repair becomes available.

if the proper procedures are not followed. Refer to the Owner's Manual, Maintenance, Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.

diagnostic trouble codes (DTCs) B1175:19, B1176:19, B11C0:19 and/or B11C1:19 present in door latch control module E (DCME), door latch control module F (DCMF), door latch control module G (DCMG) and/or door latch control module H (DCMH). This may be due to low battery voltage and DTC thresholds being too low and not a fault in the door latch assembly. Engineering is releasing updated software to resolve this concern, which is expected to be available by the end of June-2022. In the meantime, clear these DTC's and if any reset with normal battery voltage follow normal Workshop Manual diagnostics and repair. Monitor OASIS for updates.

stability-traction control and/or powertrain malfunction warning indicators with diagnostic trouble codes (DTCs) C00A8:11, C00A8:13, C00A6:71, C00A6:74, and C00A6:99 present in the AWD module. This may be due to a damaged wiring harness rubbing against the underbody heat shield where it routes over and into the transfer case actuator motor. Inspect the wire harness for damage and repair as necessary following the procedures in the Wiring Diagram Manual. If no damage is found, continue with normal diagnostics.

Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.

If diagnostics lead to a motor replacement, visually inspect the original motor for signs of water intrusion. If found, determine source of water leak prior to replacing the motor. Refer to Workshop Manual (WSM), Section 501-17, Pinpoint Test A for 2011-2016 and Pinpoint Test B for 2017-2022 for identifying the source of the water leak.

automatic transmission may exhibit a harsh/delayed engagement and/or a harsh/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or overhaul the main control valve body.

Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.

SYNC screen when adjusting the climate control temperature. This may be due to the SYNC software installed in the accessory protocol interface module (APIM). Engineering is currently developing a software update that is expected in January 2022. Once the software update is available, it will be made available to customers who have enabled SYNC 3 Automatic Updates with their vehicle connected to a Wi-Fi network. Repair appointments should be scheduled for customers in February 2022 who do not receive Automatic Updates. Monitor OASIS for updates.

when adjusting the climate control temperature. This may be due to the SYNC software installed in the accessory protocol interface module (APIM). Engineering is currently developing a software update that is expected in January 2022. Once the software update is available, it will be made available to customers who have enabled SYNC 3 Automatic Updates with their vehicle connected to a Wi-Fi network. Repair appointments should be scheduled for customers in February 2022 who do not receive Automatic Updates. Monitor OASIS for updates.

Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a 10R60/10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or overhaul main control valve body.

the degrees do not appear in the SYNC screen. This may be due to the SYNC software installed in the accessory protocol interface module (APIM). Engineering is currently developing a software update that is expected in January 2022. Once the software update is available, contact the customer and schedule a follow-up appointment for repair in February 2022. Monitor OASIS for updates.

DTC B1088:87 may be present in the DDM. To correct the condition perform the Driver Door Module (DDM) configuration application using the Ford diagnostic scan tool. After running the configuration application, perform a window learn routine via the ford diagnostic scan tool. The condition can also be resolved by letting the vehicle enter a deep sleep cycle. Engineering is currently investigating this concern and will be releasing a service fix. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

This feature automatically adjusts airflow in the cabin to prevent the windshield from fogging up and may be perceived by customers as irregular climate control functionality. To reduce fogging, the EWAFS functions include: the air condition (A/C) button may turn on and off automatically, recirculated air may turn off automatically in all air modes except MAX A/C, recirculated air may also turn on and off automatically in various airflow modes in order to improve heating or cooling efficiency, and in auto climate control, high humidity conditions may automatically engage A/C compressor, increase blower motor speed and/or direct more air to windshield. Continue to monitor the Workshop Manual (WSM) for EWAFS updates.

This may be due to water intrusion into the cooling fan relay, a loose ground connection, or damaged wiring. Before replacement of the cooling fan assembly, perform Pinpoint Test KN. Also, locate the cooling fan relay and inspect for water intrusion or damage. The correct location of the cooling fan relay is in the front right portion of the engine bay. If the cooling fan relay is not in the correct location, check behind the front right wheel well in between the splash shield. If any water intrusion or damage is found to the relay, G103, or the connector C1048, replace and correctly mount the affected component as necessary.

vehicle and/or less than optimal speaker sound from the vehicle. This may be due to the engine sound enhancement (ESE) on Explorer ST vehicles and the active noise control (ANC) on Aviator vehicles not being activated. To correct the condition, use the Ford Diagnosis and Repair System (FDRS) > select Toolbox > ACM > ACM - Enable Engine Sound Enhancement and Active Noise Control. Click RUN and follow the on-screen instructions carefully. If prompted with a window stating Feature Not Supported, select OK and continue through the installation application. For claiming use causal 18K810 and applicable labor operations found in Section 10 of the Service Labor Time Standards (SLTS) Manual.

phone call by the person that is not in the vehicle. Using Apple CarPlay and Android Auto instead of Bluetooth can help alleviate the concern. Also turning on, then off, the privacy setting in the SYNC touchscreen can temporarily alleviate the concern. Engineering is currently investigating this concern and will be releasing a service fix in early July 2021. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. Monitor OASIS for updates.

If during the preliminary inspection the transmission fluid is found to be a foamy pink color this may indicate possible cross contamination of engine coolant and transmission fluid due to an internally leaking transmission fluid cooler assembly. When repairing or replacing the transmission assembly for an internally leaking transmission fluid cooler assembly, use causal part 7869 and applicable labor operations in Section 07 of the Service Labor Time Standards (SLTS) Manual.

with engine speed around 1500 RPM at idle or while driving. This may be due to the transmission park manual release cable vibrating against the transmission. This can be resolved by isolating the transmission park manual release cable with Rotunda PVC foam tape (164-R4901) or equivalent, where it is contacting the transmission. Replacement of the transmission park manual release cable is not necessary.

to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

exhibit a harsh engagement/harsh shift/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. Most vehicles will improve and no longer exhibit the condition after the first 8,000 km (5,000 mi) of driving. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or overhaul main control valve body.

with engine speed around 1500 RPM at idle or while driving. This may be due to the transmission park manual release cable vibrating against the transmission. This can be resolved by isolating the transmission park manual release cable with Rotunda PVC foam tape (164-R4901) or equivalent, where it is contacting the transmission. Replacement of the transmission park manual release cable is not necessary.

rubbing/clicking/ticking noise while driving that increases with vehicle speed. This may be due to the engine mount vacuum control tube contacting the left front axle halfshaft. If the engine mount vacuum control tube is contacting the left front axle halfshaft, reposition as needed.

enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.

break and move out of position. A dislocated valve plunger may lead to the driver experiencing any of the following symptoms: Hard brake pedal, over-braking condition, and if certain other conditions are present, longer brake pedal travel with an incremental increase in stopping distance that would be accompanied by a red brake warning indicator lamp on the instrument panel cluster

the proper procedures are not followed. Refer to the Owners Guide, Maintenance, Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.

exhibit a harsh 7-6 gear downshift. This may be caused by the A clutch piston return spring snap ring becoming dislodged. To correct the condition, follow the Service Procedure steps to replace the front support and A clutch assemblies.

preferred charge time scheduling using the touchscreen and/or Lincoln Way phone application. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.

indicator lamp (MIL) and/or Engine Coolant Over Temperature warning with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0128, P0217, P0330, P1026, P1299, and/or P130D. This may be due to the engine coolant temperature (ECT) sensor or ECT sensor wiring harness. For 2.3L vehicles, replace the ECT sensor and pigtail wiring connector (GU2Z-14S411-KA). For 3.0L vehicles, replace the ECT and knock sensor. To aid with the engineering investigation, do not disconnect the wiring connector from the ECT sensor during disassembly. Leave the connector on the sensor in case parts are called back for analysis.

For diagnostic assistance, contact Webasto Charging Systems, Inc. directly at 888-219-6747 or at evscs@webasto.com.

exhibit inoperative air conditioning, an illuminated malfunction indicator lamp, and/or an illuminated powertrain malfunction (wrench) indicator with various diagnostic trouble codes present and a blown fuse F14. This may be due to wiring harness 14290 chaffing on the A/C compressor pulley. If chaffing is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Make sure that the wiring harness retainer is fully seated in the back side of the bracket on the A/C compressor to keep the harness away from the compressor pulley.

idle with the air conditioning (A/C) on. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.

exhibit a harsh engagement/harsh shift/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P0751, P0756, P0761, P0766, P0771, P2707, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. Most vehicles will improve and no longer exhibit the condition after the first 8,000 km (5,000 mi) of driving. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or replace the main control valve body.

harsh shifts and/or a buck/jerk/hesitation condition at low speeds with no diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.

enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.

authorization, inoperative remote features and/or a message stating the system cannot access the Lincoln/FordPass Connect feature in the application due to being a fleet vehicle. Replacing the TCU will not resolve this condition. Engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.

supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

inoperative or does not cool properly. This may be due to a low refrigerant charge and/or system leak. Normal Workshop Manual (WSM) diagnosis and testing procedures may not verify any leaks. If this occurs, pressurize the system and spray the brazed joint of the thermostatic expansion valve manifold and tube assembly with soapy water just above where the retaining bracket/insulator bolts to the right side frame rail and check for leaks.

04-Aug-2020 may exhibit an illuminated malfunction indicator lamp (MIL) and/or engine overheating fault message with diagnostic trouble codes (DTCs) P0217 and/or P06EF stored in the powertrain control module (PCM). This may be due to an assembly pin left in the accessory drive belt tensioner during the production process. To correct the condition, remove any assembly pins from the accessory drive belt tensioner. If no pins are found, refer to Workshop Manual (WSM), Section 303-06 or Section 303-03 for further diagnostics.

a lack of power steering assist at initial engine start-up with diagnostic trouble code (DTC) C102D stored in the power steering control module (PCSM). This may be due to the software in the PCSM. During normal diagnostics in Workshop Manual (WSM), Section 211-02, if pinpoint test (PPT) step AI5 is answered YES, reprogram the PCSM with the latest software level of the appropriate Ford diagnostic scan tool. If DTC C102D returns, continue with normal diagnostics. For claiming, use causal part 3504 and applicable labor operations in Sections 03 and 10 of the Service Labor Time Standards (SLTS) Manual.

Some 2020 Explorer/Aviator vehicles built on or before 19-May-2020 and equipped with a 10R60 automatic transmission may exhibit a harsh 7-6 gear downshift. This may be caused by the A clutch piston return spring snap ring becoming dislodged. To correct the condition, follow the Service Procedure steps to replace the front support and A clutch assemblies.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P062C or P179D stored in the powertrain control module (PCM) and a possible lack of power. This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.

illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0BCD stored in the inverter system controller (SOBDMC). This may be due to the software in the SOBDMC. To correct the condition, reprogram the SOBDMC with the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 7B012 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

proper procedures are not followed. Refer to the Owners Guide, Maintenance, Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.

(MIL) with diagnostic trouble codes (DTCs) P0C48, P0C49, P2B29, P0CFF, P0E1F, P0C4B, P0C4A, P2CF3, P0A06, P0A07, P2D01, P2D00, P2D03, P2D04, P0C73, and/or P2D02 stored in the powertrain control module (PCM). This may be due to the software in the battery energy control module (BECM). To correct the condition, follow the Service Procedure to reprogram the BECM.

exhibit a harsh 7-6 gear downshift. This may be caused by the A clutch piston return spring snap ring becoming dislodged. To correct the condition, follow the Service Procedure steps to replace the front support and A clutch assemblies.

indicator lamp (MIL) and/or Engine Coolant Over Temperature warning with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0128, P0217, P0330, P1026, P1299, and/or P130D. This may be due to the engine coolant temperature (ECT) sensor or ECT sensor wiring harness. To correct the condition, replace the ECT and knock sensor. To aid with the engineering investigation, do not disconnect the wiring connector from the ECT sensor during disassembly. Leave the connector on the sensor in case parts are called back for analysis.

trying to select a point of interest using the push to talk feature on the navigation system. Engineering is currently working on a solution for this condition, which is expected to be available in July. Please monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

in the instrument panel cluster (IPC) with diagnostic trouble codes (DTCs) B1041 and U2100 stored in the SUMA. This may be due to the SUMA entering into a diagnostic service mode after an on-demand self-test or module replacement. If no other DTCs are present, use the latest software version of the appropriate Ford diagnostic scan tool to run the SUMA-Transport and Factory Mode Deactivation function to clear the DTCs. Run an ALL Continuous Memory DTC test to verify DTCs have cleared as running an On-Demand Self-Test on the SUMA will set the DTCs again. If other DTCs are present, refer to Workshop Manual (WSM), Section 204-05 for normal diagnostics. Engineering is investigating. Monitor OASIS for updates.

engine may exhibit slow fuel fill, premature shut off, and/or spit back during refueling. This may be due to the interface between the fuel nozzle and the fuel tank filler pipe. When refueling, advise customers to make sure to rotate the fuel nozzle 30 degrees in either direction, retract the fuel nozzle slightly within the capless filler inlet, and/or use a different refueling pump. Engineering is currently working on a solution for this condition, which is expected to be available in the fourth quarter of 2020. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

crackling and/or distorted sound from one or more speakers (but not all speakers). This may be due to other components located near the suspect speaker. Workshop Manual (WSM), Section 415-00 > Diagnosis and Testing > Pinpoint Test D (2020-2024 Explorer/Police Interceptor Utility, 2025-2026 Aviator) and Pinpoint Test E (2020-2024 Aviator, 2025-2026 Explorer/Police Interceptor Utility) have been updated with additional direction when isolating the cause of the condition.

allow the projection height to be adjusted.

diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.

Some 2020-2024 Explorer/Aviator vehicles may exhibit a lack of audio and/or a water leak in the rear liftgate area and/or water in the spare tire area. The customer may indicate that this concern is more noticeable after a car wash or rainfall. To correct the condition, follow the Service Procedure to identify the leak path.

Some 2020-2024 Explorer/Aviator non-hybrid vehicles may exhibit radio static and/or poor radio sound quality when moving. This may be more noticeable on AM radio stations. This may be caused by an electromagnetic interference concern

This may be more noticeable on AM radio stations. This may be caused by an electromagnetic interference concern. To correct the condition, follow the Service Procedure to install new grounds on the rear knuckle.

bezel rattle while audio volume is playing from speakers that could be mistakenly diagnosed as a speaker issue. This may be due to the natural frequencies of the switch and bezel when excited by sound. To diagnose, perform Workshop Manual (WSM) Section 415-00 > Pinpoint Test E1. Use the 100Hz audio sample file from the Speaker Audio Test link within Pinpoint Test E1, and adjust fade and balance settings to passenger front speaker. If the rattle is isolated to the passenger door switch bezel, remove per WSM Section 501-11. Apply Rotunda flock tape (164-R4903) over the underside of the bezel and the switch in a U-shape, then reassemble. Rerun Pinpoint Test E1 to verify the repair. If the rattle persists, perform the remaining Pinpoint Test E steps.

entertainment system may experience the audio is not synchronized with the video display when using the vehicle speakers. To correct this condition, contact the VOXX Customer Service Department at 1-866-869-7888. For claiming, refer to the Warranty and Policy manual for Ford Licensed Accessories.

The customer may indicate that this concern is more noticeable after a car wash or rainfall. To correct the condition, follow the Service Procedure to identify the leak path.

In order to correct the condition, make sure to completely follow the diagnostics in Workshop Manual (WSM), Section 415-00, Pinpoint Test D for vehicles without SYNC 3, and WSM, Section 415-00B, Pinpoint Test E for vehicles equipped with SYNC 3. If the diagnostics point towards speaker replacement, remove and re-center the speaker, making sure to tighten to the specified torque and retest. Refer to WSM, Section 415-00.

This may be more noticeable on AM radio stations. This may be caused by an electromagnetic interference concern. To correct the condition, follow the Service Procedure to install new grounds on the rear knuckle.

are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns including but not limited to: Sirius audio not functioning properly after a key cycle with active subscription Presets not responding or indicating properly Intermittent audio echo/robotic voice heard during a Bluetooth phone call Wi-Fi connection message pop-up every key cycle Frozen unresponsive touchscreen Solid blue screen when moving forward at speeds above 16 km/h (10 mph) (2019 vehicles only) Rear parking aid camera remains on the screen at speeds below 16 km/h (10 mph) (2019 vehicles only) Inoperative infotainment applications Poor/no AppLink function Apple CarPlay not launching on connection or a black screen when connected Voice prompts that skip or have short pauses while directions are being provided

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

have intermittent Phone-as-a-key connectivity, missing Phone-as-a-key button in the App, receiving Pairing Failed, Key Download Error or Connection Trouble message during Phone-as-a-key setup, Bluetooth Disconnected, Unable To Start, Backup Code Needed And/or Key Not Detected. Prior to performing any RFA diagnostics, verify the customer's phone app is at the latest version, the phone app is authorized to the vehicle and Location Service is enabled in customer's phone to allow for proper Phone-as-a-key operation. If a Phone-as-a-key concern remains, continue with normal RFA diagnosis. Refer to Workshop Manual (WSM), Section 419-01. Utilize the FordPass Guides or Lincoln Way Concierge teams as needed to understand Phone-as-a-key operation.

when using the Ford Pass/Lincoln Way mobile app. Customers may report that the vehicle location that is displayed is the Ford manufacturing facility were the vehicle was assembled, yet all other features work as intended. This may be due to the vehicle location not updating since assembly. If all other Ford Pass/Lincoln Way features work correctly except for the vehicle location, open the customer connectivity settings on the SYNC display and verify that the location setting is enabled. If the setting is currently enabled, disable and then re-enable the feature. If the vehicle location is still displayed incorrectly in the app, follow Workshop Manual section 415-00 for further diagnosis.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14H092 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Escape/Corsair/Aviator/Explorer/Expedition/Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure

Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.

If only the scheduling portion of the remote start system is not functioning, please ensure that the latest level of SYNC software has been installed. If the remote start system is not functioning using the key fob and/or the on-demand remote start function from FordPass or Lincolnway application, refer to Workshop Manual (WSM), Section 303-06 for further diagnosis.

entertainment system may experience an issue where the audio not synchronized with the video display when using the vehicle speakers. To correct this condition, contact the VOXX Customer Service Department at 1-866-869-7888. For claiming, refer to the Warranty and Policy manual for Ford Licensed Accessories.

(EBB) built on or before 1-Aug-2022 may exhibit an illuminated anti-lock brake system (ABS) warning indicator and stability-traction control warning indicator with diagnostic trouble code (DTC) U3000:96 erroneously stored in the ABS module. This condition occurs during connection or power interrupt to the EBB module. If this code is stored and the ABS system has been reassembled, clear the DTC code using Ford Diagnosis and Repair System (FDRS) scan tool and check for recurrence. If the DTC persists, perform normal diagnostics. Refer to the Workshop Manual (WSM), Section 206-09 Anti-Lock Brake System. For claiming use the causal part number 2C219 and applicable labor operations in Section 2 of the Service Labor Time Standards.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

customer is using a Magsafe iPhone (iPhone 12 or 13): slow charging, inoperative, notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen display is not showing. This may be due to a compatibility issue between the customer's phone and the wireless accessory charging module (WACM) that may make it difficult for Ford and Lincoln vehicles to wirelessly charge these specific phones. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using a Magsafe iPhone such as an iPhone 12 or 13, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.

lamp (MIL) with diagnostic trouble codes (DTCs) U0100, P1A42 and/or P1A43 stored in battery energy control module (BECM). This may be due to software in the PCM. To correct the condition, follow the service procedure to perform a coordinated flash on the powertrain control module (PCM), secondary on-board diagnostic module c (SOBDMC), anti-lock braking system (ABS) module, BECM, and battery charger control module (BCCM).

The customer may state that the anti-locking brake system (ABS) system is activating without any indicators on the instrument panel cluster (IPC). This may be due to the regenerative braking software in the ABS module. To correct the condition, follow the Service Procedure Steps to perform a coordinated flash on the powertrain control module (PCM) and ABS module.

When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.

charging, a notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen is not showing. This may be due to the customer's phone if they are using an iPhone 12. Vehicles equipped with a wireless charging pad are designed to charge best with phones that follow the Qi standard. The iPhone 12 hardware currently does not follow the Qi standard for wireless charging. This may make it difficult for Ford and Lincoln vehicles to wirelessly charge this specific phone. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using an iPhone 12, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.

center on vehicle start-up with no diagnostic trouble codes (DTCs) stored in the anti-lock brake system (ABS) module. This may be due to the software in the ABS module. To correct the condition, follow the Service Procedure steps to reprogram the powertrain control module (PCM) and/or ABS module using the latest software level of the appropriate Ford diagnostic scan tool.

illuminated anti-lock brake system (ABS) warning indicator lamp with diagnostic trouble code (DTC) C0020 stored in the ABS module. It may not be necessary to replace the ABS module/hydraulic control unit (HCU) to resolve DTC C0020. This may be due to a poor ground connection and/or improper plating on the attachment bolts at G108. To correct the condition, follow the Service Procedure to replace and properly tighten the ground cable fasteners.

Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles built on or before 24-Dec-2020 may exhibit an illuminated anti-lock brake system (ABS) warning indicator lamp with diagnostic trouble code (DTC) C0020 stored in the ABS module. It may not be necessary to replace the ABS module/hydraulic control unit (HCU) to resolve DTC C0020. This may be due to a poor ground connection and/or improper plating on the attachment bolts at G108. To correct the condition, follow the Service Procedure to replace and properly tighten the ground cable fasteners.

(DTCs) U0415 and/or U3000:42 in the image processing module B (IPMB). These DTCs may be associated with camera display issues or a Reverse Brake Assist Unavailable fault message. To correct the condition, reprogram the IPMB using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19H405 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

(ABS) warning lamp with diagnostic trouble codes (DTCs) C0031, C0034, C0037, and/or C003A. This may be due to metal contamination on the wheel speed sensors or wheel speed sensor rings. Verify that all wheel speed sensors and wheel speed sensor rings are free of metal contamination before replacing them. Refer to Workshop Manual (WSM), Section 206-09 for diagnostics.

anti-lock brake system (ABS) warning indicator lamp with diagnostic trouble code (DTC) C0020 stored in the ABS module. It may not be necessary to replace the ABS module/hydraulic control unit (HCU) to resolve DTC C0020. This may be due to a poor ground connection and/or improper plating on the attachment bolts at G108. To correct the condition, follow the Service Procedure to replace and properly tighten the ground cable fasteners.

transmitter, Lincoln Way App, and the passive entry system door handles. The door keypad and the mechanical key will be the only option to unlock the vehicle when this concern is present. In addition to the inability to unlock the vehicle, the vehicle may also exhibit a no crank/no start symptom. To address this condition, reprogram the body control module (BCM) using the appropriate Ford diagnostic scan tool. For claiming, use causal part 15604 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

with windshield washer fluid contaminated with brake fluid. If a vehicle exhibits a-pillar and/or rear liftgate trim or tail lamp appearance concerns, collect a sample of the washer fluid using a suction device and place in a white paper or Styrofoam cup. Washer fluid that appears green in color would indicate the washer fluid has been contaminated. Flush the washer fluid system and repair the affected windshield a-pillar area and liftgate area as necessary.

before 15-Jul-2020 may exhibit various warning/fault indicators with diagnostic trouble codes (DTCs) C006A:74 and/or P166E stored in the AWD module and/or U0102 stored in the anti-lock brake system (ABS) module. This may be due to the software in the AWD module. To correct the condition, reprogram the AWD module with the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 7P238 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Some 2020 Explorer/Aviator/Corsair vehicles built on or before 23-Jul-2020 may inadvertently activate the reverse braking assist system while backing up. This may be perceived as the system is too sensitive to surrounding objects. This may be due to the software in the image processing module B (IPMB). To correct the condition, follow the Service Procedure to reprogram the IPMB, as well as the accessory protocol interface module (APIM) to allow the vehicle to remember the last setting of reverse brake assist when the vehicle is restarted.

initial vehicle start up with diagnostic trouble code (DTC) C0047:64 stored in the anti-lock brake system (ABS) module. The vehicle may also exhibit an illuminated ABS, Advance Trac, and/or red brake warning lamp, and possible Advance Trac Fault message displayed. This may be due to the software in the ABS module. To correct the condition, reprogram the ABS module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 2005 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

initial vehicle start up with diagnostic trouble code (DTC) C0047:64 stored in the anti-lock brake system (ABS) module. The vehicle may also exhibit an illuminated ABS, Advance Trac, and/or red brake warning lamp, and possible Advance Trac Fault message displayed. This may be caused by the software in the ABS module. To correct the condition, reprogram the ABS module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 2005 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.

delayed engagement/shift concerns. Refer to Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing for normal diagnostics. The WSM has been updated with information from previously published articles related to this concern.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

fluid venting condition.

(7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.

malfunction (wrench) lamp with diagnostic trouble code (DTC) P084B stored in the PCM. The Workshop Manual (WSM) has recently been updated to provide new direction for DTC P084B.

lines on the center display screen with multi color or rainbow hue. This may be due to SYNC module (APIM) software. To correct the condition, run the APIM-SYNC Module (APIM) Standard Programming application using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

has lines on the center display screen with multi color or rainbow hue. This may be due to accessory protocol interface module (APIM) software. To correct the condition, run the APIM-SYNC Module (APIM) Standard Programming application using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

has lines on the center display screen with multi color or rainbow hue. This may be due to accessory protocol interface module (APIM) software. To correct the condition, run the APIM-SYNC Module (APIM) Standard Programming application using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

on or before 15-Nov-2022 may exhibit an 8th gear start after coming to a stop and/or a no movement in Reverse condition. This may be due to the driver applying the accelerator pedal and brake pedal simultaneously during regenerative braking. To improve the condition, follow the Service Procedure to reprogram the powertrain control module (PCM) and refer the customer to the Automatic Transmission Section of the Owners Manual warning regarding applying both pedals simultaneously.

Strategy Download application in the Ford Diagnosis and Repair System (FDRS) to be run after certain transmission or module repairs. The Transmission Strategy Download routine is failing in FDRS levels 32.5.3 and 32.5.4. The FDRS development team is working to resolve this in a future release of FDRS. In the meantime, uninstall FDRS from the computer using the select all function to remove all data and recordings. Reinstall the older FDRS version 31.6.5 using this url - http://www.fordservicecontent.com/Ford_Content/IDS/FDRS/FDRS_31.6.5.exe Once 31.6.5 is installed, download and run the Transmission Strategy Download application.

This may be due to water intrusion between the transmission and the transfer case. The transfer case installation procedure has been updated in Workshop Manual (WSM), Section 307-07B to prevent this concern from reoccurring. Follow the updated WSM procedure to make sure the top of the transfer case is sealed upon installation.

diagnostic trouble code (DTC) C00A6:07, C00A6:18, C00A6:19, C00A6:4B, C00A6:66, C00A6:71, C00A6:74, and/or C00A6:99. It may not be necessary to replace the transfer case clutch actuator. Follow the updated transfer case clutch actuator Pinpoint Tests in the Workshop Manual (WSM), Section 308-07A for 2020 vehicles and Section 307-07A for 2021 vehicles.

code (DTC) P27B2 stored in the powertrain control module (PCM) memory. This DTC may be present due to activation of the transmission park by wire manual release during vehicle assembly and has not yet achieved the 40 warm up cycles needed to be cleared from memory. Before attempting a repair for this DTC, clear the DTC and if it returns, refer to the WSM, Section 307-01 for normal diagnostics. For claiming, use causal part 12A650 and applicable labor times in section 10 of the Service Labor Time Standards (SLTS) Manual.

This may be due to the natural harmonic frequency of the pipe. To correct the condition, follow the Service Procedure to install a worm gear clamp over the exhaust flexible pipe.

travel when the transmission is initially placed in gear with no diagnostic trouble codes (DTCs) stored in the anti-lock brake system (ABS) module. This condition only occurs at initial vehicle start-up and will no longer be present after the brake pedal is released and re-applied during the same key cycle. This is not a lack of power brake assist. This may be caused by the software in the ABS module. To correct the condition, reprogram the ABS module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 2005 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

This may be due to the natural harmonic frequency of the pipe. To correct the condition, follow the Service Procedure to install a worm gear clamp over the exhaust flexible pipe.

less than 100 miles may exhibit a transmission fluid leak that appears to be coming from between the hybrid drive unit and transmission case joint. This condition may be due to residual transmission fluid trapped between the front module and transmission case joint during the assembly process. Recommend cleaning the area thoroughly and reevaluating with the vehicle at operating temperature before attempting any leak related repairs.

Manual" message in the instrument panel cluster (IPC) after installing a replacement fuel filler door assembly (7827936). This may be due to a concern with the replacement fuel filler door assembly. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and Ford is currently working on a solution for this condition that is expected Q3 2026. Further replacement of the fuel filler door assembly will not resolve this condition at this time. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.<br /><br /> If a customer vehicle exhibits this concern, submit a Vehicle Concern Report. To submit a report, click on the "Submit Global Concern Report (GCR)" link at the upper right of the PTS Vehicle ID screen (vehicle identification number VIN required) a

Manual" message in the instrument panel cluster (IPC) after installing a replacement fuel filler door assembly (7827936). This may be due to a concern with the replacement fuel filler door assembly. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

Some 2020-2022 Escape/Corsair vehicles built on or before 3-Jan-2022, 2020-2022 Explorer vehicles built on or before 14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.

14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.

information.

The correct label should show Evap: LFMXR0165LDG. Owners of affected vehicles will be mailed the VECI label and installation instructions early May 2022. Owners will be given the option of installing the labels themselves, or they can have their dealer perform the service for them.

09-Apr-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

inoperative driver door window control switch (windows inoperative, mirror control unresponsive, etc.).

may experience the overhead console sunglass bin cannot be locked in a closed position.

The vent register is now available separately (service base part number 19893). It is no longer necessary to replace the entire loadspace trim panel.

This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.

This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.

To correct the condition, follow the Service Procedure steps to identify the leak path.

Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.

Replacement If Required After Dealer Evaluation

Replace Front and/or Side Cameras if Foggy

sensation while turning and/or while accelerating from low speeds. The concern may also be described as a grinding and/or chatter noise. If the Workshop Manual (WSM) leads to replacement of the rear axle, inspect the differential for damage and differential fluid for metallic chunks in the fluid. Note that some metallic flake in the fluid and/or discoloration is normal and the rear axle should not be replaced for it. If no damage is found to the rear differential, it is not recommended to replace the rear axle assembly. Refer to WSM Symptom Charts (Section 308-07A for 2020 model year; Section 307-07A for 2021 model year) for diagnosis of the transfer case instead.

sensation while turning and/or while accelerating from low speeds. The concern may also be described as a grinding and/or chatter noise. If the Workshop Manual (WSM) leads to replacement of the rear axle, inspect the differential for damage and differential fluid for metallic chunks in the fluid. Note that some metallic flake in the fluid and/or discoloration is normal and the rear axle should not be replaced for it. If no damage is found to the rear differential, it is not recommended to replace the rear axle assembly. Instead, refer to the Symptom Charts in WSM, Section 307-07A for further diagnosis of the transfer case.

Replace Front and/or Side Cameras if Foggy

sensation while turning and/or while accelerating from low speeds. The concern may also be described as a grinding and/or chatter noise. If the Workshop Manual (WSM) leads to replacement of the rear axle, inspect the differential for damage and differential fluid for metallic chunks in the fluid. Note that some metallic flake in the fluid and/or discoloration is normal and the rear axle should not be replaced for it. If no damage is found to the rear differential, it is not recommended to replace the rear axle assembly. Instead, refer to the Symptom Charts in WSM, Section 308-07 for further diagnosis of the transfer case.

Some vehicles listed in the model statement above may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) C00A6 and/or C0631. This may be due to the front axle disconnect actuator/intermediate shaft.

Some vehicles listed in the model statement above may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) C00A6 and/or C0631. This may be due to the front axle disconnect actuator/intermediate shaft.

Some vehicles listed in the model statement above may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) C00A6 and/or C0631. This may be due to the front axle disconnect actuator/intermediate shaft.

Some 2020-2022 Explorer/Aviator/Corsair vehicles may experience seat pan looseness, lateral movement and/or clunk/thump noise on turns. To correct the condition, follow the Service Procedure steps to reinforce the cushion hook.

Workshop Manual (WSM) Pinpoint Tests G (driveline shudder) and H (driveline vibration) have been updated in WSM, Section 205-01.

fold, exhibit excess effort to fold, or do not slide forward/backward easily. Power or manual second row seats must be pushed forward manually during easy entry function since the assist spring will reduce but not eliminate manual effort. Refer to the Owner's Manual > Seats > Rear Seats > Adjusting the Second Row Rear Seats for further details. If the seats do not easily push forward manually, it maybe due to tension in the seat track due to uneven assembly torque. To correct these conditions, unbolt the second row seat frame from the floor to relax tension. Start the bolts by hand, then tighten in the correct sequence and torque per Workshop Manual (WSM) Section 501-10B.

Complete front air spring/strut assemblies are now available and can be replaced instead of replacing individual components of the front air spring or front struts for warranty and retail repairs. Part numbers are LC5Z-3C098-A (right) and LC5Z-3C098-C (left) for non-hybrid vehicles, and LC5Z-3C098-B (right) and LC5Z-3C098-D (left) for hybrid vehicles. Front spring/strut assembly replacement is recommended to make sure a successful repair is performed.

message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTCs) B1041 and U2100 stored in the SUMA. This may be due to the SUMA entering diagnostic service mode after an on-demand (OD) self-test following suspension system diagnosis or repair. Use the Ford Diagnosis and Repair System (FDRS) > SUMA > Run All CM (Continuous Memory) DTCs. Do not run FDRS > SUMA > OD and CM DTCs to prevent invalid DTCs. If an OD self-test was run, clear DTCs using FDRS > SUMA > Transport and Factory Mode Deactivation function. For other DTCs refer to Workshop Manual (WSM), Section 204-05 (Vehicle Dynamic Suspension) for normal diagnostics.

To assist with diagnosis and service of the air suspension system, the WSM has been updated. Refer to WSM, Section 204-05, Vehicle Dynamic Suspension > General Procedures > Air Suspension System Depressurize and Pressurize for the updated procedure.

inner/outer CV joint boot for various reasons. If Workshop Manual (WSM), Section 205-04 > Diagnosis and Testing leads to CV joint boot replacement, L1MZ-3A331-G (Explorer/Police Interceptor Utility front inner/outer CV joint boot kit), L1MZ-3A331-H (Aviator front inner/outer CV joint boot kit), L1MZ-3A331-F (Explorer/Police Interceptor Utility front inner CV joint boot kit) and L1MZ-3A331-E (Aviator front inner CV joint boot kit) have been released for service. Refer to WSM, Section 205-04 for Removal and Installation procedures.

front A-pillar applique (either side or both). This may be due to a small gap between the outboard side of the A-pillar applique and the moulding. To correct the condition, follow the Service Procedure to install thin strips of flock tape on the A-pillar applique.

To correct the condition, follow the Service Procedure steps to reinforce the cushion hook.

and/or vibration felt through the seat, steering wheel and/or center console at 25-50 mph (40-80 km/h). This may be due to constant velocity (CV) joint instability at dynamic angles close to zero. To correct the condition, follow the Service Procedure to install a driveline shim.

through the seat, steering wheel and/or center console after initial driveaway between 25-50 MPH (40-80 Km/h) that lessens after driving 5-10 minutes. This may be due to driveshaft center bearing bounce mode during cold ambient temperatures. To resolve the concern, install a softer durometer L1MZ-4A499-F driveshaft center bearing per Workshop Manual Section 205-01. For claiming, use causal part 4A499 and applicable labor operations in Section 4 of the Service Labor Time Standards (SLTS) Manual.

noise during up or down travel, including ingress/egress and/or driver memory function. This symptom may be more prevalent with warmer interior temperatures and/or during summer months. This may be due to a lack of lubrication in the steering column. To correct the condition, follow the Service Procedure to replace the steering column.

an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) C00A6 and/or C0631. This may be due to the front axle disconnect actuator/intermediate shaft. To correct the condition, follow the Service Procedure to replace the front axle disconnect actuator/intermediate shaft with a revised intermediate shaft.

an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) C00A6 and/or C0631. This may be due to the front axle disconnect actuator/intermediate shaft. To correct the condition, follow the Service Procedure to replace the front axle disconnect actuator/intermediate shaft with a revised intermediate shaft.

This may be due to tension built up within the seat and seat track that leads to more force required to manually fold the seat. To correct the condition, the second row seat frame will need to be unbolted from the floor and tightened in the correct sequence. Additionally, the sliding tracks of the seat should be inspected for proper alignment when tightening the bolts. It is important to note that the bolts should be started by hand before tightening to the correct torque. This sequence is outlined in Workshop Manual (WSM), Section 501-10. The WSM has been updated to reflect the updated bolt installation procedure.