2020 Lexus Ux Hybrid TSBs

This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing the battery rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger.

After performing a Health Check, one or both of the following Diagnostic Trouble Codes (DTCs) may be present: ?P1C8449 ? (High Voltage Power Resource Circuit Short during Ready ON) ?P300449 ? (High Voltage Power Resource Circuit Short during Pre-Charge) Follow the Repair Procedure in this bulletin to address this condition.

?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App does not accept the activation code. ?Lexus App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Lexus App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h and 2021 model year ES 250 vehicles may exhibit one or more of the following conditions: ?Depleted 12V vehicle battery when in IG-OFF. ?Unable to reconnect out of network. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.

?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App does not accept the activation code. ?Lexus App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Lexus App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h and 2021 model year ES 250 vehicles may exhibit one or more of the following conditions: ?Depleted 12V vehicle battery when in IG-OFF. ?Unable to reconnect out of network. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.

This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing the battery rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger

This Service Bulletin should be used in conjunction with the applicable model and model year Electronic Wiring Diagram (EWD) and/or Repair Manual.

?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App does not accept the activation code. ?Lexus App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Lexus App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h and 2021 model year ES 250 vehicles may exhibit one or more of the following conditions: ?Depleted 12V vehicle battery when in IG-OFF. ?Unable to reconnect out of network. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.

?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App does not accept the activation code. ?Lexus App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Lexus App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h vehicles may exhibit the following condition: ?Depleted 12V vehicle battery when in IG-OFF. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.

This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing the battery rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger.

In addition, some models may also utilize retaining clips for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips.

In order to properly diagnose and determine the root cause it?s important to follow a structured process to identify any contributing issues and determine the proper remedy.

?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App does not accept the activation code. ?Lexus App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Lexus App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.

battery cooling fan or intake filter. This condition could reduce the efficiency of the HV battery cooling system.

battery cooling fan or intake filter. This condition could reduce the efficiency of the HV battery cooling system.

A GFCI breaker can be tripped for various reasons, one of the reasons may be related to the DCA-8000. We are investigating this issue to determine the root cause. Other reasons the GFCI breaker may trip ?Circuit demand is too high for GFCI rating ?Worn out GFCI internal contacts ?Improper installation or wiring of GFCI breaker

?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App does not accept the activation code. ?Lexus App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Lexus App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. A firmware update is now available to address these conditions. Follow the Firmware Update Procedure in this bulletin to update the firmware.

?The lashing holes are intended to be plugged during Pre-Delivery Service (PDS). ?The plugs are -Required for anti-corrosion purposes. -Usually located in the glove box prior to PDS. ?The number of plugs may be different based on model and production location.

system warning lamp occurring during below-freezing temperatures (< 32F). This condition may occur at start-up after a short-distance drive. After performing a Health Check, the Diagnostic Trouble Codes (DTCs) U011087 and U029387 may be present. These codes are because of the IGCT (90987-02025) relay not being able to supply power to HV ECU. Follow the Repair Procedure in this bulletin to address this condition.

a ?Good? condition, the DCA will automatically enter a post-test charging mode. In the post-test charging mode, the DCA analyzes the current state of charge of the battery and automatically begins to charge the battery to a fully charged condition, 100% state of charge. The time required to charge the battery to full will vary. Once the DCA enters the post-test charging mode the battery test has been completed, and further charging can be conducted under the Technician?s discretion. Selecting ?Stop? will cancel the automatic charging of the battery and return the user to the DCA results screen. The test results and charge time can be printed or emailed from the results screen.

If there are no DTCs present and after the initial SOS light flashing sequence after ignition on, neither the red nor green light stays on in the overhead console determine if the vehicle is in shipping mode. To determine if a vehicle is experiencing this condition, connect a Techstream and navigate to: Telematics-Data List - ?Telematics Activation Status?. If this value is displayed as ?Shipping?, continue to the Shipping Mode recommendations below, and do not create a TAS case

This condition is characterized by no DTCs present and after the initial SOS light flashing sequence after ignition on, neither the red nor green light stays on in the overhead console. To determine if a vehicle is experiencing this condition, connect a Techstream and navigate to: Telematics-Data List - ?Telematics Activation Status?. If this value is displayed as ?Shipping?, continue to the recommendations below, and do not create a TAS case.

Below is an explanation of what information is required when testing a 12V battery on the new Warranty Battery Testers.

Please see L-SB-0004-26.

These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

Please see L-SB-0006-25.

These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features.

Please see L-SB-0007-23

established, vehicle settings and/or network/cellular coverage concerns.

established, vehicle settings and/or network/cellular coverage concerns

inoperative when attempting to send commands to the vehicle. To simplify the diagnosis of this system and prevent the unnecessary replacement of parts, please refer to the procedure below.

Please see L-SB-0036-21.

being established, vehicle settings and/or network/cellular coverage concerns.

Please see L-SB-0043-20.

diagnostic information in one document.

Please see L-SB-0036-20.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

This condition can occur on vehicles with less than 10,000 miles.

accept the activation code and/or becomes inoperative, and/or the SOS call center does not receive the vehicle?s location data in a timely manner.

Please see L-SB-0003-20.

To simplify the diagnosis of this system and prevent the unnecessary replacement of parts, please refer to the procedure below.

Please see L-SB-0025-19.

(SST) USB flash drive to update the map, points of interest, and system software.

The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.

The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.

(SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations.

Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the expiration date of the dynamic subscription (stored in the head unit), must be checked. If the expiration date has not passed, a license key may be generated without the purchase of an activation card number (ACN). Updating the map without the use of an ACN is considered an Embedded Navigation Update (refer to pg. 10) and performing this update does not extend the subscription to dynamic map services. If the subscription period has expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an ACN. Utilizing an ACN, will initiate the Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the embedded navigation update and provide dynamic map services for a period of two years from the date that the Dynamic Navigation Update is performed. ACNs are provided in a pamphlet available through the normal parts ordering system

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs.

The date that is shown could be more than one year in the future. This does not indicate any issues with the vehicle and is only informing the user of the expiration date.

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs.

Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update; however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the head unit?s expiration date must be checked. If the expiration date is still valid, a license key may be generated without the use of an activation card number. Updating the maps without the use of an activation card number is considered an Embedded Navigation Update (refer to pg. 10) and performing this process does not extend the duration of telematic map services. If the head unit?s expiration date is expired or will expire within the next 90 days, it should be recommended to the customer to purchase an activation number. Utilizing an activation number will initiate a Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the Embedded Navigation Update and provide telematic map services for a period of two years from the day that the Dynamic Navigation Update is performed. Activation card numbers are provided in an activation card number pamphlet available through the normal parts ordering system.

Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update; however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the head unit?s expiration date must be checked. If the expiration date is still valid, a license key may be generated without the use of an activation card number. Updating the maps without the use of an activation card number is considered an Embedded Navigation Update (refer to pg. 10) and performing this process does not extend the duration of telematic map services. If the head unit?s expiration date is expired or will expire within the next 90 days, it should be recommended to the customer to purchase an activation number. Utilizing an activation number will initiate a Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the Embedded Navigation Update and provide telematic map services for a period of two years from the day that the Dynamic Navigation Update is performed. Activation card numbers are provided in an activation card number pamphlet available through the normal parts ordering system.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address this condition.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address this condition.

The date that is shown could be more than one year in the future. This does not indicate any issues with the vehicle, and is only informing the user of the expiration date.

Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update; however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the head unit?s expiration date must be checked. If the expiration date is still valid, a license key may be generated without the use of an activation card number. Updating the maps without the use of an activation card number is considered an Embedded Navigation Update (refer to pg. 10) and performing this process does not extend the duration of telematic map services. If the head unit?s expiration date is expired or will expire within the next 90 days, it should be recommended to the customer to purchase an activation number. Utilizing an activation number will initiate a Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the Embedded Navigation Update and provide telematic map services for a period of two years from the day that the Dynamic Navigation Update is performed. Activation card numbers are provided in an activation card number pamphlet available through the normal parts ordering system. Follow the process in this bulletin to perform the update.

During Pre-Delivery Service (PDS), follow the instructions contained within the Software Confirmation section of this bulletin to ensure that the software is installed correctly. If it is found that the software is not installed correctly, proceed to the Software Installation section of this bulletin. It may also be necessary to reinstall the eOM software after replacing the head unit. Refer to the Software Confirmation section of this bulletin to determine if the software is already installed. If the software is not installed, proceed to the USB Flash Drive Preparation and Software Installation sections of this bulletin.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Lexus vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. L-PG004-94. The entire bulletin has been updated.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Lexus vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. L-PG004-94. The entire bulletin has been updated.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003-93, PG002-90, L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003 93, and PG002-90. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1990 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin.

The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.

of the following conditions: ?Abnormal Bluetooth Audio Mode transition. ?Difficult radio tune knob operation when selecting audio source. Some 2020 ? 2021 model year Lexus vehicles equipped with Pioneer Audio (version 1799) or earlier may exhibit one or more of the following conditions: ?Album art inoperative. ?Low Volume from CarPlay FaceTime Audio Calls. ?Pause function intermittently inoperative in CD mode. ?Intermittent Diagnostic Trouble Code (DTC) B15FE present. ?Abnormal energy flow screen appearance on Hybrid models. ?Abnormal phone call operation during Apple CarPlay. ??No Information? displayed in Information Screen. ?No audio after voice guidance in Android Auto. ?Repeat Function Inoperative in Bluetooth Audio Mode. ?Audio does not resume after CarPlay Voicemail. ?Climate temperature control difficult to operate. ?Text message screen Reply button is inoperative using Apple iOS13 or later. Follow the Multimedia Software Update Procedure in this bulletin to install the latest software version

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

and/or related environmental factors. Follow the General Procedure in this bulletin to minimize the odors experienced.

stores and causing dealer stock to age. Due to this situation, dealers are reminded and recommended to follow the Long-Term Vehicle Storage Guidelines outlined in L-SB-0015-20 and other Service Bulletin publications to ensure customers receive their vehicles in a fresh and well maintained condition. Please ensure that both Sales and Service at your dealership are aware of these guidelines and are following the recommended maintenance and storage processes and procedures to ensure the highest customer satisfaction with their new vehicle purchase.

This DTC can be triggered during the manufacturing and/or shipping process and does not indicate a problem with the vehicle. To simplify the diagnosis of this DTC, refer to the procedure below to prevent unnecessary parts replacement.

Additionally, refer to the applicable Pre-Delivery Service (PDS) Manual and Check Sheet for services to be performed.

(versions less than 1225 or 1245 with 20 Teammate) may exhibit one or more of the following conditions: ?Navigation reset while entering a destination. ?Voice command does not recognize Starbucks. ??Unable to establish audio connection? message, and Alexa is unable to resume after Android AutoTM interruption. ?Soft buttons grayed Out during panoramic view monitor transition. ?HVAC fan speed displayed incorrectly. ?Volume cannot be adjusted with the rear seat remote control. ?Multimedia system reboots when iPhone is connected via USB. ?Energy flow information is missing on energy monitor screen. ?Clearance sonar indication on backup camera screen is missing. ?Audio from USB devices intermittently works. ?iPhone ringer continues after answering call. ?Audio titles not displayed. ?Toyota apps screen menu not displayed. Some 2020 ? 2021 model year vehicles equipped with 17CY+ Panasonic Navigation (version less than 1150) and Audio (version less than 1163) may exhibit one or more of the following conditions: ?Poor map screen touch operation. ?Navigation system reset. ?Climate temperature control difficult to operate. ??Waiting for the Beep? message displayed, voice recognition does not start when pressing the push to talk button. ?Blower motor speed incorrectly displayed. ?White CarPlay screen when connecting iPhone12. ?Navigation sub-screen blank while playing a CD. ?Inoperative rear seat entertainment track controls. ?Abnormal energy flow screen appearance. ?Incorrect FM or SiriusXM genre Information. A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to address these conditions.

?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus app does not accept the activation code. ?Lexus app is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Lexus app shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Lexus App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h and 2021 model year ES 250 vehicles may exhibit one or more of the following conditions: ?Depleted 12V vehicle battery when in IG-OFF. Some 2020 ? 2021 model year ES 350, ES 300h, UX 200, and UX 250h and 2021 model year ES 250 vehicles may exhibit one or more of the following conditions: ?Remote Engine Start inoperative (fob and app). ?Remote Engine Start inoperative (app only). ?B15CC49 backup battery malfunction. ?Power Door Lock inoperative (app and fob). Some 2020 ? 2022 model year ES 350, ES 300h, UX 200, and UX 250h, 2021 ? 2022 model year ES 250 vehicles may exhibit one or more of the following conditions: ?Connected Services inoperative. ?Safety Connect calls not completing intermittently. ?DCM signal strength grayed OUT on head unit with strike through. DCM reset and firmware update is now available to address these conditions.

(version 1163) or earlier may exhibit one or more of the following conditions: ?Poor map screen touch operation. ?Navigation system reset. ?Climate temperature control difficult to operate. ??Waiting for the Beep? message displayed, voice recognition does not start when pressing the push to talk button. ?Blower motor speed incorrectly displayed. ?White CarPlay screen when connecting iPhone12. ?Navigation sub-screen blank while playing a CD. ?Inoperative rear seat entertainment track controls. ?Abnormal energy flow screen appearance. ?Incorrect FM or SiriusXM genre Information. Some 2020 ? 2021 model year vehicles equipped with 17CY+ Panasonic Navigation (version 1110) or earlier and Audio (version 1123) may exhibit one or more of the following conditions: ?Android AutoTM music does not resume after the vehicle is turned OFF and then ON. ?Incorrect cover art is displayed from a previous song. ?CarPlay unexpectedly resumes after turning audio OFF and pushing Menu switch. ?MAP switch inoperative when in a Bluetooth call and connected to Android AutoTM. ?Pop noise when selecting track up/down of USB audio. ?Touch pad feedback continues when feedback setting is turned OFF. ?Blank navigation screen. ?Low Bluetooth audio volume. ?Bluetooth connection screen button was greyed out. ?Climate temperature control difficult to operate. ?Menu buttons do not light up when pushed. ?Blower level is not displayed correctly. Some 2020 ? 2021 model year Lexus vehicles equipped with Navigation (version 1060) or earlier and Audio (version 1060) or earlier may exhibit one or more of the following conditions: ?Display screen distortion/pixilation. A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to address these conditions.

or earlier may exhibit one or more of the following conditions: ?Display screen distortion/pixilation. ?iOS device would not connect until disconnecting and reconnecting USB cable. ?iOS device would not connect until ACC OFF > ON. Some 2020 model year Lexus vehicles equipped with Navigation (version 1030) or earlier and Audio (version 1036) or earlier may exhibit one or more of the following conditions: ?Abnormal clock operation in Auto Daylight Savings Time mode. ?CarPlay inoperative. ?USB audio does not resume after turning the engine OFF and ON. ?Reply button not displayed on the text message screen. ?Reset during phonebook transfer. ?Bluetooth calls disconnected. ?Enform submenu inoperative from touch screen. ?Push to Talk button long press starts native voice recognition. ?Destination Assist frozen when pressing SOS button. ?Navigation screen slow booting or does not boot up. Some 2020 model year Lexus vehicles equipped with Navigation (version 1006) or earlier and Audio (version 1007) or earlier, may exhibit one or more of the following conditions: ?Voice Command ?Barge-in? defaults to OFF. ?Handset Mode label incorrect. ?AndroidTM Auto music does not resume after using Destination Assist. ?Abnormal return/back arrow illumination operation. ?Destination Assist will not cancel while playing AndroidTM Auto music. ?Gracenote cover art is not displayed. ?Incorrect Destination Assist vehicle position. A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to address these conditions.

message displayed and one or more of the following DTC(s) that represent an over current between the MG1, MG2, and inverter/PCU: ?P1C5D19 ? Drive Motor "A" Inverter Circuit Current Above Threshold ?P1C5F19 ? Generator Inverter Circuit Current Above Threshold These conditions typically occur on low vehicle mileage (less than 5,000). After an occurrence, the vehicle will be able to run normally with no drivability issues. Follow the Repair Procedure in this bulletin to address these conditions.

Toyota Motor Sales, USA Required Tools. The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system and to add and/or remove a key. NOTICE When performing a Smart Code Reset, ALL registered keys are erased and CANNOT be used again on ANY vehicle. For Undesignated Key Permanent Erasure utility, ONLY the keys that are NOT present will be removed. ANY keys that are NOT present can never be reused.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Lexus paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. BO029-91. The entire bulletin has been updated. Service Bulletin No. BO029-91 is obsolete

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Lexus paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. BO029-91. The entire bulletin has been updated. Service Bulletin No. BO029-91 is obsolete

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect vehicle systems and components. Any problems that are found should be corrected immediately.

HVAC odor maintenance service using A/C Power Foam Evaporator Cleaner & Refresher.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

ST004-01, SU001-08, and L-SB-0174-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Lexus vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

or waived services during the trial.

does not accept the activation code and/or becomes inoperative, and/or the SOS call center does not receive the vehicle?s location data in a timely manner. Follow the Firmware Update Procedure in this bulletin to address these conditions.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

Service Lane - Knowledge Center.

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Lexus.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.