2015 Lexus Rc F TSBs

This Service Bulletin should be used in conjunction with the applicable model and model year Electronic Wiring Diagram (EWD) and/or Repair Manual.

If a level surface with a consistent plane is not available, use the Floor Slope Compensation Procedure in this service bulletin in conjunction with the appropriate model and model year Repair Manual instructions when adjusting the millimeter wave radar sensor.

If a level surface is not available, this tech tip should be used in conjunction with the repair manual to set the angle of the front millimeter wave radar sensor and reflector height before performing beam axis adjustment.

vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated

vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated

Vehicles were moved from Customer Support Program 19LE05 and added to Limited Service Campaign KLG. The Data Communication Module (DCM) in the subject vehicles are equipped with software to identify the location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated. Note: Lexus has initiated a Limited Service Campaign and a Customer Support Program to resolve this issue related to the Safety Connect system. Both of these programs provide the same free remedy to correct this issue with Safety Connect. Lexus recommends that customers have the free remedy performed before reactivating Safety Connect. Vehicles that had an active Safety Connect subscription on or after 10/1/2017 were included in Limited Service Campaign LSC KLG. Vehicles that did not have an active Safety Connect subscription on or after 10/1/2017 but are affected by this condition are included in this Customer Support Program (19LE05).

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated. Note: Lexus has initiated a Limited Service Campaign and a Customer Support Program to resolve this issue related to the Safety Connect system. Both of these programs provide the same free remedy to correct this issue with Safety Connect. Lexus recommends that customers have the free remedy performed before reactivating Safety Connect. Vehicles that had an active Safety Connect subscription on or after 10/1/2017 were included in Limited Service Campaign LSC KLG. Vehicles that did not have an active Safety Connect subscription on or after 10/1/2017 but are affected by this condition are included in this Customer Support Program (19LE05).

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated. Note: Lexus has initiated a Limited Service Campaign and a Customer Support Program to resolve this issue related to the Safety Connect system. Both of these programs provide the same free remedy to correct this issue with Safety Connect. Lexus recommends that customers have the free remedy performed before reactivating Safety Connect. Vehicles that had an active Safety Connect subscription on or after 10/1/2017 were included in Limited Service Campaign LSC KLG. Vehicles that did not have an active Safety Connect subscription on or after 10/1/2017 but are affected by this condition are included in this Customer Support Program (19LE05).

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated. Note: Lexus has initiated a Limited Service Campaign and a Customer Support Program to resolve this issue related to the Safety Connect system. Both of these programs provide the same free remedy to correct this issue with Safety Connect. Lexus recommends that customers have the free remedy performed before reactivating Safety Connect. Vehicles that had an active Safety Connect subscription on or after 10/1/2017 were included in Limited Service Campaign LSC KLG. Vehicles that did not have an active Safety Connect subscription on or after 10/1/2017 but are affected by this condition are included in this Customer Support Program (19LE05).

The Data Communication Module (DCM) in the subject vehicles are equipped with software to identify the location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

Batteries can become discharged due to an extended storage period, temperature, paristic drain, or while demonstrating vehicle features and bnefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life.

a calibration update is available or not. The issue is related to the Techstream software and will be corrected in a future Techstream software release.

will be inoperative due to loss of the seat position memory stored in the seat ECUs. Initialize both front memory seat ECUs after installing the D/C Cut fuse during Pre-Delivery Service (PDS).

Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.

doors or remote start the vehicle.

The Repair Procedure section, Required Tools & Equipment section, and the Repair Procedure section has been updated. Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

will be inoperative due to loss of the seat position memory stored in the seat ECUs. Initialize both front memory seat ECUs after installing the D/C Cut fuse during Pre-Delivery Service (PDS).

a calibration update is available or not. The issue is related to the Techstream software and will be corrected in a future Techstream software release.

damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

calibration update is available or not. The issue is related to the Techstream software and will be corrected in a future Techstream software release.

calibration update is available or not. The issue is related to the Techstream software and will be corrected in a future Techstream software release.

damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver's side, and if applicable, passenger's side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

BATTERIES CAN BECOME DISCHARGED DUE TO AN EXTENDED STORAGE PERIOD, TEMPERATURE, PARISTIC DRAIN, OR WHILE DEMONSTRATING VEHICLE FEATURES AND BNEFITS IN THE SALES PROCESS. BATTERY INSPECTION AND MAINTENANCE ARE REQUIRED IN ORDER TO ENSURE PROPER OPERATION AND OPTIMAL BATTERY LIFE.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address this condition.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address this condition.

L-SB-0074-14. ? The Part Information and Required Tools & Equipment, and On-Vehicle Data Navigation Update sections have been updated. Service Bulletin No. L-SB-0074-14 is obsolete and any printed versions should be discarded. Lexus models equipped with the HDD Navigation (EMV-N) system require a Special Service Tool (SST) USB drive to update the map, points of interest, Gracenote, and system software. The SST is used with all vehicles to deliver the update; however, a unique activation number is required for each vehicle. Activation numbers are provided in an Activation Card Number pamphlet available through the normal parts ordering system. Use the process described in this bulletin to perform the update.

1. First type is generation 6 or 7 which utilizes HDD (Hard Disc Drive). Pioneer models that begin with NXH, have map data, operating system and other information in the Hard Disc Drive. With this system if a radio is being sent back for an exchange. The original Hard Disc Drive needs to be removed and installed into the newly serviced radio.

L-SB-0035-15. ? The entire bulletin has been updated. Service Bulletin No. L-SB-0035-15 is obsolete and any printed versions should be discarded. Some 2015 ? 2017 model year Lexus vehicles equipped with navigation (version older than V1##8940) may exhibit one or more of the following conditions: ? Unable to download Destination Assist ? Software update date does not display ? ?Calculating? message displays on the map screen without displaying street name and remaining distance ? Unable to guide a route on the Home screen ? Black display screen ? Bluetooth disconnects intermittently. Some 2015 ? 2016 model year Lexus vehicles equipped with navigation (version older than V1##8910) may exhibit one or more of the following conditions: ? Inoperative Voice Recognition ? Same XM channel icon is used for different channels ? Loss of traffic information intermittently when using Lexus Enform ? Traffic incident mark ?!? on the map screen but no information on the traffic incident screen ? iPod scroll is stopped changing by tune knob ? Inoperative Home button ? Reset occurs while making a turn off the highlighted route ? After correction of text in Quick Message15, the corrected text displays in Quick Message13 ? Navigation system reboots intermittently ? Navigation system reboots after receiving errant weather data ? Some screens with clock information display ?12:00? as ?0:00? S

the first time on new vehicles. The download and installation process may also be performed under other circumstances such as following a head unit replacement or after the customer's personal settings are erased. The download and installation process requires between 3 and 15 minutes to complete, depending on file size, cellular connection speed, and other factors. Following the download and installation procedure, individual Enform apps may periodically update through an over-the-air update system. Follow the procedure in this bulletin to perform the download/installation procedure and app updates.

2014 IS, you may encounter disabled (i.e. greyed out) "INFO Button" links while browsing with Internet Explorer 10. You can identify the affected manuals by locating the adjustable Production Date Range, or PDR, dropdowns above the navigation tree. Only repair manuals with these drop downs will be affected.

? Navigation system becomes frozen/has no response or slow response ? Missing or incorrect HD Traffic incidents and/or flow data shown on the screen ? Resetting of the navigation system ? iPod Error is displayed with Apple device connected to the USB port ? Song Title is not updated when using Siri ? Display is blank after a Bluetooth? Audio device is connected ? No audio sound after completing a phone call ? Navigation system resets when playing an "Audio Book" on a CD ? Unable to load multiple destinations when using Destination Assist feature A software update is now available to address these conditions.

(This condition may be due to an errant data broadcast by Toyota's traffic and weather data service provider.) Follow the process in this bulletin to reset the navigation system.

A display lens with revised anti-reflective coating has been developed to address this condition.

equipped with navigation (version less than V1##8910), may exhibit one or more of the following conditions: * Voice Recognition is inoperative * Same XM channel icon is used for different channels * Loss of traffic information at times when using Lexus Enform * There is traffic incident mark "!" on the map screen, but no info on the traffic incident screen * iPod scroll is stopped changing by tune knob * After correction of text in Quick Message15, the corrected text is displayed in Quick Message13 * Navigation system reboots intermittently * Navigation system reboots after receiving errant weather data * Some screens with clock information show 12:00 as 0:00 Some 2015 Lexus CT 200h, IS, NX, ES, RC, GS, and LS models equipped with navigation (version less than V1##8872), or GX 460 vehicles equipped with navigation (version less than V1##8871) may exhibit one or more of the following conditions: * Navigation system becomes frozen/has no response or slow response * Missing or incorrect HD Traffic incidents and/or flow data shown on the screen * Resetting of the navigation system * iPod Error is displayed with Apple device connected to the USB port * Song Title is not updated when using Siri * Display is blank after a Bluetooth? Audio device is connected * No audio sound after completing a phone call * Navigation system resets when playing an "Audio Book" on a CD * Unable to load multiple destinations when using destination Assist feature * HOME button does not work * Reset while making a turn off of the highlighted route

2014 IS, you may encounter disabled (i.e. greyed out) "INFO Button" links while browsing with Internet Explorer 10. You can identify the affected manuals by locating the adjustable Production Date Range, or PDR, dropdowns above the navigation tree. Only repair manuals with these drop downs will be affected.

? Navigation system becomes frozen/has no response or slow response ? Missing or incorrect HD Traffic incidents and/or flow data shown on the screen ? Resetting of the navigation system ? iPod Error is displayed with Apple device connected to the USB port ? Song Title is not updated when using Siri ? Display is blank after a Bluetooth? Audio device is connected ? No audio sound after completing a phone call ? Navigation system resets when playing an "Audio Book" on a CD ? Unable to load multiple destinations when using Destination Assist feature A software update is now available to address these conditions.

memory.

1. First type is generation 6 or 7 which utilizes HDD (Hard Disc Drive). Pioneer models that begin with NXH, have Map Data, Operating System and other Information in the Hard Disc Drive. With this system if a radio is being sent back for an exchange. The original Hard Disc Drive needs to be removed and installed into the newly serviced radio. 2. The Second type is Generation 8 Navigation system which utilizes the Micro SD Card. Pioneer models that begin with NXF, have map data in the Micro SD card. This is a customer accessible Micro SD card which can be found behind the front flip cover. The original Micro SD card should be removed and installed into the newly serviced radio.

L-SB-0035-15. ? The entire bulletin has been updated. Service Bulletin No. L-SB-0035-15 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Some 2015 ? 2017 model year Lexus vehicles equipped with navigation (version older than V1##8940) may exhibit one or more of the following conditions: ? Unable to download Destination Assist ? Software update date does not display ? ?Calculating? message displays on the map screen without displaying street name and remaining distance ? Unable to guide a route on the Home screen ? Black display screen ? Bluetooth disconnects intermittently

1. First type is generation 6 or 7 which utilizes HDD (Hard Disc Drive). Pioneer models that begin with NXH, have Map Data, Operating System and other Information in the Hard Disc Drive. With this system if a radio is being sent back for an exchange. The original Hard Disc Drive needs to be removed and installed into the newly serviced radio. 2. The Second type is Generation 8 Navigation system which utilizes the Micro SD Card. Pioneer models that begin with NXF, have map data in the Micro SD card. This is a customer accessible Micro SD card which can be found behind the front flip cover. The original Micro SD card should be removed and installed into the newly serviced radio.

This is only a reference list of tools that might be in dealership inventory and not meant to be a diagnostic or repair procedure. Generation 7 navigation systems use a USB SST to update firmware and map. Generation 8 navigation systems use a USB stick to update the firmware only.

are used for the first time on new vehicles. The download and installation process may also need to be performed under other circumstances such as following a head unit replacement or after the customer's personal settings are erased. The download and installation process requires between 3 and 15 minutes to complete, depending on the file size, cellular connection speed, and other factors. Following the download and installation process, small Enform? App updates may also occur via an over the air update system. Follow the procedure below to perform the download and installation process.

A DISPLAY LENS WITH REVISED ANTI-REFLECTIVE COATING HAS BEEN DEVELOPED TO ADDRESS THIS CONDITION.

THIS IS ONLY A REFERENCE LIST OF TOOLS THAT MIGHT BE IN DEALERSHIP INVENTORY AND NOT MEANT TO BE A DIAGNOSTIC OR REPAIR PROCEDURE. GENERATION 7 NAVIGATION SYSTEMS USE A USB SST TO UPDATE FIRMWARE AND MAP. GENERATION 8 NAVIGATION SYSTEMS USE A USB STICK TO UPDATE THE FIRMWARE ONLY.

ARE USED FOR THE FIRST TIME ON NEW VEHICLES. THE DOWNLOAD AND INSTALLATION PROCESS MAY ALSO NEED TO BE PERFORMED UNDER OTHER CIRCUMSTANCES SUCH AS FOLLOWING A HEAD UNIT REPLACEMENT OR AFTER THE CUSTOMER'S PERSONAL SETTINGS ARE ERASED. THE DOWNLOAD AND INSTALLATION PROCESS REQUIRES BETWEEN 3 AND 15 MINUTES TO COMPLETE, DEPENDING ON THE FILE SIZE, CELLULAR CONNECTION SPEED, AND OTHER FACTORS. FOLLOWING THE DOWNLOAD AND INSTALLATION PROCESS, SMALL ENFORM APP UPDATES MAY ALSO OCCUR VIA AN OVER THE AIR UPDATE SYSTEM. FOLLOW THE PROCEDURE BELOW TO PERFORM THE DOWNLOAD AND INSTALLATION PROCESS.

(THIS CONDITION MAY BE DUE TO AN ERRANT DATA BROADCAST BY TOYOTA'S TRAFFIC AND WEATHER DATA SERVICE PROVIDER.) FOLLOW THE PROCESS IN THIS BULLETIN TO RESET THE NAVIGATION SYSTEM.

Please see L-SB-0008-20. Replacement Certification Labels and VIN Plates

Please see L-SB-0003-20.

Please see L-SB-0017-19.

established, vehicle settings and/or network/cellular coverage concerns.

Once the system is reset, all previously registered keys will be erased.

This condition has been remedied, and DCM activation utilizing Techstream can now be resumed.

Please see L-SB-0144-17.

This is a known condition and will be remedied in the near future. Please discontinue DCM activations utilizing Techstream until further notice.

Please see L-SB-0006-18.

Please see L-SB-0001-18.

Once the system is reset, all previously registered keys will be erased.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003-93, PG002-90, L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003 93, and PG002-90. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1990 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

intrusion due to improper sealer application. If this occurs, corrosion may form causing rust spots, paint blistering, or perforation of the rear fender arch. This condition is most likely to occur in areas with heavy road salt application.

If this occurs, corrosion may form causing rust spots, paint blistering, or perforation of the rear fender arch. This condition is most likely to occur in areas with heavy road salt application.

due to improper sealer application. If this occurs, corrosion may form causing rust spots, paint blistering, or perforation of the rear fender arch. This condition is most likely to occur in areas with heavy road salt application.

If this occurs, corrosion may form causing rust spots, paint blistering, or perforation of the rear fender arch. This condition is most likely to occur in areas with heavy road salt application.

due to improper sealer application. If this occurs, corrosion may form causing rust spots, paint blistering, or perforation of the rear fender arch. This condition is most likely to occur in areas with heavy road salt application.

The door lock can be placed in the middle position between lock and unlock when exiting the vehicle. This can cause the door lock to be inoperative. APPLICABLE WARRANTY: This repair is covered under the Lexus Basic Warranty. This warranty is in effect for 48 months or 50,000 miles, whichever occurs first, from the vehicle's in-service date. Warranty application is limited to occurrence of the specified condition described in this bulletin.

L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003-93, and PG002-90. Service Bulletin Nos. L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003-93, and PG002-90 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Vehicle replacement certification labels (vinyl label installed on driver door or door post) and VIN lates (metal plate riveted to dashboard) may be available from Lexus, provided the request meets one of the criteria listed in this Service Bulletin.

Some 2014 ? 2016 model year Lexus vehicles may not unlock with either the Smart Entry or the wireless remote. The door lock can be placed in the middle position between lock and unlock when exiting the vehicle. This can cause the door lock to be inoperative.

? February 11, 2015 Rev1: Applicability has been updated to include 2006 ? 2015 model year Lexus vehicles. On some vehicles, when Rapgard? is removed, the paint may have a stained appearance. These stains appear to be under the clear coat. The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture. Use the following procedure to address this condition.

If this occurs, corrosion may form causing rust spots, paint blistering, or perforation of the rear fender arch. This condition is most likely to occur in areas with heavy road salt application.

These stains appear to be under the clear coat. The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture. Use the following procedure to address this concern.

When this condition occurs, the Active Rear Wing does not retract during normal driving and cannot be retracted with the switch on the instrument panel. Follow the Repair Procedure in this bulletin to address this condition.

These stains appear to be under the clear coat. The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture. Use the following procedure to address this concern.

When this condition occurs, the Active Rear Wing does not retract during normal driving and cannot be retracted with the switch on the instrument panel. Follow the Repair Procedure in this bulletin to address this condition.

inconsistent air temperature coming from the air conditioner (A/C) vents, air not coming out at the selected temperature, and/or air not coming out of the selected A/C vent of the vehicle. Although the A/C servo motors are covered by Lexus? New Vehicle Limited Warranty for 4 years or 50,000 miles (whichever comes first), we at Lexus care about the customers? ownership experience. Lexus is providing coverage for repairs related to A/C servo motor(s) that have an internal electrical malfunction which could lead to the symptoms described above.

?Uneven temperature or air flow between the vents. ?Little or no air flow from the vent(s). ?Improper MODE control function. Additionally, some vehicles may store one or more of the following HVAC servo Diagnostic Trouble Codes (DTCs). ?B1441 ? Air Mix Damper Control Servo Motor Circuit (Front Passenger Side Lower Air Mix). ?B1442 ? Air Inlet Damper Control Servo Motor Circuit. ?B1443 ? Air Outlet Damper Control Servo Motor Circuit. ?B1446 ? Air Mix Damper Control Servo Motor Circuit (Driver Side Lower Air Mix). ?B1447 ? Rear Air Mix Damper Control Servo Motor Circuit. ?B1448 ? Passenger Side Face Servo Motor Circuit. ?B1449 ? Rear Air Outlet Damper Control Servo Motor Circuit. ?B1453 ? Driver Side Air Outlet Damper COOL Control Servo Motor Circuit. ?B1454 ? Passenger Side Air Outlet Damper COOL Control Servo Motor Circuit. ?B1455 ? Driver Side Air Outlet Damper FOOT/DEF Control Servo Motor Circuit. Follow the procedures in this bulletin to address this condition.

?Uneven temperature or air flow between the vents ?Little or no air flow from the vent(s) ?Improper MODE control function Additionally, some vehicles may store one or more of the following HVAC servo Diagnostic Trouble Codes (DTCs). ?B1441 ? Air Mix Damper Control Servo Motor Circuit (Front Passenger Side Lower Air Mix) ?B1442 ? Air Inlet Damper Control Servo Motor Circuit ?B1443 ? Air Outlet Damper Control Servo Motor Circuit ?B1446 ? Air Mix Damper Control Servo Motor Circuit (Driver Side Lower Air Mix) ?B1447 ? Rear Air Mix Damper Control Servo Motor Circuit ?B1448 ? Passenger Side Face Servo Motor Circuit ?B1449 ? Rear Air Outlet Damper Control Servo Motor Circuit ?B1453 ? Driver Side Air Outlet Damper COOL Control Servo Motor Circuit ?B1454 ? Passenger Side Air Outlet Damper COOL Control Servo Motor Circuit ?B1455 ? Driver Side Air Outlet Damper FOOT/DEF Control Servo Motor Circuit Follow the procedure in this bulletin to address this condition.

inconsistent air temperature coming from the air conditioner (A/C) vents, air not coming out at the selected temperature, and/or air not coming out of the selected A/C vent of the vehicle. Although the A/C servo motors are covered by Lexus? New Vehicle Limited Warranty for 4 years or 50,000 miles (whichever comes first), we at Lexus care about the customers? ownership experience. Lexus is providing coverage for repairs related to A/C servo motor(s) that have an internal electrical malfunction which could lead to the symptoms described above.

inconsistent air temperature coming from the air conditioner (A/C) vents, air not coming out at the selected temperature, and/or air not coming out of the selected A/C vent of the vehicle. Although the A/C servo motors are covered by Lexus? New Vehicle Limited Warranty for 4 years or 50,000 miles (whichever comes first), we at Lexus care about the customers? ownership experience. Lexus is providing coverage for repairs related to A/C servo motor(s) that have an internal electrical malfunction which could lead to the symptoms described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

L-SB-0021-14. G1765 Applicability has been updated to include applicable 2018 models and 2016 ? 2018 model year RC 300 and 2015 ? 2018 model year RC 350 vehicles. ? Applicability has been updated to exclude 2001 ? 2003 model year ES 300 vehicles. Service Bulletin No. L-SB-0021-14 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines the use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Lexus term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ECU is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Lexus-specific control unit

The Engine Control Module (ECM) logic has been modified to reduce the possibility of this condition. Please follow the Repair Procedure below to address this condition.

Trouble Code (DTC) P2610 (Engine Off Timer Performance) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition.

L-SB-0021-14. * Applicability has been updated to include applicable 2018 models and 2016 * 2018 model year RC 300 and 2015 * 2018 model year RC 350 vehicles. * Applicability has been updated to exclude 2001 - 2003 model year ES 300 vehicles. Service Bulletin No. L-SB-0021-14 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines the use of TIS and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Lexus term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ECU is used as a generic label for the following SAE J1930 standard references: * Powertrain Control Module (PCM) * Engine Control Module (ECM) * Transmission Control Module (TCM) * Any other Lexus-specific control unit

vehicle app that enables you to connect to Lexus Enform Technology and manage your Lexus from any distance (as long as both your vehicle & smartphone are able to establish cellular connections). The app allows you to remotely lock/unlock your doors and start/stop the engine, find your parked vehicle, set speed/distance alerts for guest drivers, and send you the lock/unlock status after turning your vehicle off. Lexus Enform Remote is optimized for you r smartphone but not for tablets.

Batteries can become discharged due to an extended storage period, temperature, parasitic drain, or while demonstrating vehicle features and benefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As described in this bulletin, operating the engine for 30 minutes after 60 days in storage and every 30 days thereafter will help to maintain battery State of Charge (SOC). This process supplements other movements of the vehicle as it is staged, and has specific restrictions on how maintenance is to be done. Also described in this bulletin are 2 other approved methods for maintaining battery State of Charge.

vehicle app that enables you to connect to Lexus Enform Technology and manage your Lexus from any distance (as long as both your vehicle & smartphone are able to establish cellular connections). The app allows you to remotely lock/unlock your doors and start/stop the engine, find your parked vehicle, set speed/distance alerts for guest drivers, and send you the lock/unlock status after turning your vehicle off. Lexus Enform Remote is optimized for you r smartphone but not for tablets.

Batteries can become discharged due to an extended storage period, temperature, parasitic drain, or while demonstrating vehicle features and benefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As described in this bulletin, operating the engine for 30 minutes after 60 days in storage and every 30 days thereafter will help to maintain battery State of Charge (SOC). This process supplements other movements of the vehicle as it is staged, and has specific restrictions on how maintenance is to be done. Also described in this bulletin are 2 other approved methods for maintaining battery State of Charge.

and temporarily stored in the blank space of the relay block in the engine compartment. During Pre-Delivery Service (PDS), reinstall the D/C Cut fuse into its original location.

Each tire (except the spare tire) has a tire pressure warning valve/transmitter and the measured tire pressure data is sent to the tire pressure warning antenna by electric wave and then sent to the receiver.

and temporarily stored in the blank space of the relay block in the engine compartment. During Pre-Delivery Service (PDS), reinstall the D/C Cut fuse into its original location.

THE ENGINE CONTROL MODULE (ECM) LOGIC HAS BEEN MODIFIED TO REDUCE THE POSSIBILITY OF THIS CONDITION. PLEASE FOLLOW THE REPAIR PROCEDURE BELOW TO ADDRESS THIS CONDITION.

THE ENGINE CONTROL MODULE (ECM) LOGIC HAS BEEN MODIFIED TO REDUCE THE POSSIBILITY OF THIS CONDITION. PLEASE FOLLOW THE REPAIR PROCEDURE BELOW TO ADDRESS THIS CONDITION.

Wheel offset, deffined as the distance between the wheel's - to - rotor mounting surface, affects the clearance between the back of the wheel and surrounding brake components .

Wheel offset, defined as the distance between the wheel?s centerline and the wheel-to-rotor mounting surface, affects the clearance between the back of the wheel and surrounding brake components (Figure 1). Installation of a wheel with an offset or width different than the correct specification, such as installing the rear wheel on the front, can cause damage to brake components due to interference between the wheel and adjacent parts. The wheel could contact the brake caliper thereby introducing stress into the caliper, brake rotor, and potentially other components. In some cases, this stress could contribute to cracking or separation of the brake rotor.

L-SB-0054-15. Applicability has been updated to include 2017 model year RC F vehicles. Service Bulletin No. L-SB-0054-15 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. All 2015 - 2019 model year RC F vehicles are equipped with high-friction brake pads, specifically designed for superior braking performance and response. As a result, the brakes may exhibit a squeal/squeak noise. For customers who find these characteristics objectionable, brake pads with alternative material are now available as service parts. NOTE: Any changes made to the brake pad material may result in altered and possibly reduced braking performance and/or feeling under certain driving conditions, including track use. Please note disclosures stated in the RC F sales information both in print form and online and discuss with the customer prior to installing the alternate brake pads listed in this Service Bulletin. It is an inherent characteristic of materials and design of brake pads used in this high-performance brake system that brake noise/squeal/squeak may result.

As a result, the brakes may exhibit a squeal or squeak type noise. For customers who find these characteristics objectionable, brake pads with alternative material are now available as service parts. Note: Any changes made to the brake pad material, may result in altered and possibly reduced braking performance and/or feeling under certain driving conditions, including track use. Service Manager Note: Please note disclosures stated in the RC F sales information both in print form and online and discuss with the customer prior to installing the alternate brake pads listed in this service bulletin. It is an inherent characteristic of materials and design of brake pads used in this high-performance brake system that brake noise/squeal may result.

Wheel offset, defined as the distance between the wheel's centerline and the wheel-to-rotor mounting surface, affects the clearance between the back of the wheel and surrounding brake components. Installation of a wheel with an offset or width different than the correct specification, such as installing the rear wheel on the front, can cause damage to brake components due to interference between the wheel and adjacent parts. The wheel could contact the brake caliper thereby introducing stress into the caliper, brake rotor, and potentially other components. In some cases, the stress could contribute to cracking or seperation of the brake rotor.

even one lug nut over or under torqued, can cause a vibration issue * When lug nuts are over torqued, this causes the rotor to have a runout out condition which can lead to brake vibration concerns * Brake vibration issues can occur at parking lot to highway speeds * Brake vibration issues can occur at light to moderate braking * Tightening lug nuts in a star pattern method during the torqueing process will assure that even/equal pressure is applied across the rotor hub surface * Torque sticks/wrenches should be used to apply accurate torque values when tightening * Do Not use impact guns/ratchets to completely run lug nuts up to the wheel surface

Wheel offset, defined as the distance between the wheel's centerline and the wheel-to-rotor mounting surface, affects the clearance between the back of the wheel and surrounding brake components. Installation of a wheel with an offset or width different than the correct specification, such as installing the rear wheel on the front, can cause damage to brake components due to interference between the wheel and adjacent parts. The wheel could contact the brake caliper thereby introducing stress into the caliper, brake rotor, and potentially other components. In some cases, the stress could contribute to cracking or seperation of the brake rotor.

As a result, the brakes may exhibit a squeal or squeak type noise. SUPERSESSION NOTICE: The information contained in this bulletin supersedes SB No. L-SB-0054-15. Applicability has been updated to include 2017 model year RC F vehicles. Service Bulletin No. L-SB-0054-15 is obsolete and any printed versions should be discarded.

As a result, the brakes may exhibit a squeal or squeak type noise. SUPERSESSION NOTICE: The information contained in this bulletin supersedes SB No. L-SB-0054-15. Applicability has been updated to include 2017 model year RC F vehicles. Service Bulletin No. L-SB-0054-15 is obsolete and any printed versions should be discarded.

The condition can occur at any time if improper torque is applied to lug nuts. Over time, even one lug nut over- or under-torqued can cause a vibration condition. When lug nuts are over-torqued, this causes the rotor to have a runout condition, which can lead to brake vibration conditions.

2015 - 2016 RC F vehicles are equipped with high-friction brake pads, specifically designed for superior braking performance and response. As a result, the brakes may exhibit a squeal or squeak type noise.

As a result, the brakes may exhibit a squeal or squeak type noise. For customers who find these characteristics objectionable, brake pads with alternative material are now available as service parts. NOTE: Any changes made to the brake pad material, may result in altered and possibly reduced braking performance and/or feeling under certain driving conditions, including track use.

loaded in the luggage compartment at the assembly plant to avoid damage in transit. Install the front wheel opening extension pads on the vehicle during Pre-Delivery Service (PDS).

AS A RESULT, THE BRAKES MAY EXHIBIT A SQUEAL OR SQUEAK TYPE NOISE. FOR CUSTOMERS WHO FIND THESE CHARACTERISTICS OBJECTIONABLE, BRAKE PADS WITH ALTERNATIVE MATERIAL ARE NOW AVAILABLE AS SERVICE PARTS. NOTE: ANY CHANGES MADE TO THE BRAKE PAD MATERIAL, MAY RESULT IN ALTERED AND POSSIBLY REDUCED BRAKING PERFORMANCE AND/OR FEELING UNDER CERTAIN DRIVING CONDITIONS, INCLUDING TRACK USE."

VEHICLE LOCATION INACCURATE

VEHICLE LOCATION INACCURATE

Vehicles were moved from Customer Support Program 19LE05 and added to Limited Service Campaign KLG.

Refer to the Dealer Letter, FAQ, and Technical Instructions on TIS for additional information. in areas with heavy road salt application.

the vehicle at the assembly plant. Install the mounting bracket during Pre-Delivery Service (PDS) according to one of the following 2 installation procedures (depending on what bracket is made available), ONLY on vehicles requiring a front license plate.

the vehicle at the assembly plant. Install the mounting bracket during Pre-Delivery Service (PDS) according to one of the following 2 installation procedures (depending on what bracket is made available), ONLY on vehicles requiring a front license plate.

Install the mounting bracket during Pre-Delivery Service (PDS) according to one of the following 2 installation procedures (depending on what bracket is made available), ONLY on vehicles requiring a front license plate.

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

ST004-01, SU001-08, and L-SB-0174-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Lexus vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

connectivity concerns such as: Difficulty to pair the phone. Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

Bluetooth failure to connect to the vehicle when first turning on the vehicle, Various Bluetooth Audio functions are no longer functioning with the customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.

Bluetooth failure to connect to the vehicle when first turning on the vehicle, Various Bluetooth Audio functions are no longer functioning with the customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Lexus.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

Install the mounting bracket during Pre-Delivery Service (PDS) according to the following interim installation procedure ONLY on vehicles requiring a front license plate.

Install the mounting bracket during Pre-Delivery Service (PDS) according to the following interim installation procedure ONLY on vehicles requiring a front license plate.

If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Please refer to the following procedure to ensure that the original tires stay in the same location on the vehicle.

converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.

assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.

mileage between scheduled maintenance checks. Here are some important tips when working with ATF-WS in Lexus vehicles requiring its use.

CONNECT SYSTEM ? VEHICLE LOCATION INACCURATE CERTAIN 2011 ? 2017 MODEL YEAR LS, 2013 ? 2016 MODEL YEAR LS Hybrid, 2011 ? 2017 MODEL YEAR GS, 2016 ? 2017 MODEL YEAR GS-F, 2013 ? 2017 MODEL YEAR GS Hybrid, 2010 ? 2017 MODEL YEAR IS, 2011 ? 2015 MODEL YEAR IS-C, 2013 ? 2014 MODEL YEAR IS-F, 2015 ? 2017 MODEL YEAR RC, 2015 ? 2017 MODEL YEAR RC-F, 2011 ? 2017 MODEL YEAR CT, 2010 ? 2017 MODEL YEAR RX, 2010 ? 2017 MODEL YEAR RX Hybrid, 2015 ? 2017 MODEL YEAR NX, 2015 ? 2017 MODEL YEAR NX Hybrid, 2010 ? 2017 MODEL YEAR LX, 2010 ? 2018 MODEL YEAR GX, 2010 ? 2017 MODEL YEAR ES, 2013 ? 2017 MODEL YEAR ES Hybrid Updated 10/17/2019

INACCURATE CERTAIN 2011 ? 2017 MODEL YEAR LS, 2013 ? 2016 MODEL YEAR LS Hybrid, 2011 ? 2017 MODEL YEAR GS, 2016 ? 2017 MODEL YEAR GS-F, 2013 ? 2017 MODEL YEAR GS Hybrid, 2010 ? 2017 MODEL YEAR IS, 2011 ? 2015 MODEL YEAR IS-C, 2013 ? 2014 MODEL YEAR IS-F, 2015 ? 2017 MODEL YEAR RC, 2015 ? 2017 MODEL YEAR RC-F, 2011 ? 2017 MODEL YEAR CT, 2010 ? 2017 MODEL YEAR RX, 2010 ? 2017 MODEL YEAR RX Hybrid, 2015 ? 2017 MODEL YEAR NX, 2015 ? 2017 MODEL YEAR NX Hybrid, 2013 ? 2017 MODEL YEAR LX, 2013 ? 2018 MODEL YEAR GX, 2010 ? 2017 MODEL YEAR ES, Updated 9/13/2019

INACCURATE CERTAIN 2011 ? 2017 MODEL YEAR LS, 2013 ? 2016 MODEL YEAR LS Hybrid, 2011 ? 2017 MODEL YEAR GS, 2016 ? 2017 MODEL YEAR GS-F, 2013 ? 2017 MODEL YEAR GS Hybrid, 2010 ? 2017 MODEL YEAR IS, 2011 ? 2015 MODEL YEAR IS-C, 2013 ? 2014 MODEL YEAR IS-F, 2015 ? 2017 MODEL YEAR RC, 2015 ? 2017 MODEL YEAR RC-F, 2011 ? 2017 MODEL YEAR CT, 2010 ? 2017 MODEL YEAR RX, 2010 ? 2017 MODEL YEAR RX Hybrid, 2015 ? 2017 MODEL YEAR NX, 2015 ? 2017 MODEL YEAR NX Hybrid, 2013 ? 2017 MODEL YEAR LX, 2013 ? 2018 MODEL YEAR GX, 2010 ? 2017 MODEL YEAR ES, 2013 ? 2017 MODEL YEAR ES Hybrid

INACCURATE CERTAIN 2011 ? 2017 MODEL YEAR LS, 2013 ? 2016 MODEL YEAR LS Hybrid, 2011 ? 2017 MODEL YEAR GS, 2016 ? 2017 MODEL YEAR GS-F, 2013 ? 2017 MODEL YEAR GS Hybrid, 2010 ? 2017 MODEL YEAR IS, 2011 ? 2015 MODEL YEAR IS-C, 2013 ? 2014 MODEL YEAR IS-F, 2015 ? 2017 MODEL YEAR RC, 2015 ? 2017 MODEL YEAR RC-F, 2011 ? 2017 MODEL YEAR CT, 2010 ? 2017 MODEL YEAR RX, 2010 ? 2017 MODEL YEAR RX Hybrid, 2015 ? 2017 MODEL YEAR NX, 2015 ? 2017 MODEL YEAR NX Hybrid, 2013 ? 2017 MODEL YEAR LX, 2013 ? 2018 MODEL YEAR GX, 2010 ? 2017 MODEL YEAR ES, 2013 ? 2017 MODEL YEAR ES Hybrid

model year Lexus vehicles.

GX 460, IS 300/350/200t, NX 200t/300h, and RC F/350/300/200t vehicles. Any previous printed versions of this bulletin should be discarded.

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner's Manual will highlight the importance of proper maintenance and provide guidance for care.

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care. NOTE Leather seat covers that are replaced for dye transfer or soiling are NOT eligible for replacement under warranty. Likewise, damage caused by unapproved cleaning methods are NOT eligible for replacement under warranty.

AS AN ADDITIONAL RESOURCE, IF THE VEHICLE IS EQUIPPED WITH FACTORY LEATHER SEATS, THE VEHICLE OWNER'S MANUAL WILL HIGHLIGHT THE IMPORTANCE OF PROPER MAINTENANCE AND PROVIDE GUIDANCE FOR CARE.

In the event that injector seal repair is required on vehicles equipped with a direct injection fuel system, a Special Service Tool Set is required to properly install the seal onto the injector. As new vehicle configurations have been released, several injector seal tool sets have been distributed to accommodate these new vehicles. There are a total of three injector seal tool sets for Lexus models, located in the appropriate SST cabinets. Each kit contains multiple pieces as shown in the diagram below. The individual pieces must remain together to ensure these tools are used correctly. Refer to the repair manual for the tool information to ensure the correct tool is used for the desired application.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle's systems and components. Any problems that are found should be corrected immediately.