2016 Lexus Rc 350 TSBs

This Service Bulletin should be used in conjunction with the applicable model and model year Electronic Wiring Diagram (EWD) and/or Repair Manual.

If a level surface with a consistent plane is not available, use the Floor Slope Compensation Procedure in this service bulletin in conjunction with the appropriate model and model year Repair Manual instructions when adjusting the millimeter wave radar sensor.

If a level surface is not available, this tech tip should be used in conjunction with the repair manual to set the angle of the front millimeter wave radar sensor and reflector height before performing beam axis adjustment.

vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated

vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated

Vehicles were moved from Customer Support Program 19LE05 and added to Limited Service Campaign KLG. The Data Communication Module (DCM) in the subject vehicles are equipped with software to identify the location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated. Note: Lexus has initiated a Limited Service Campaign and a Customer Support Program to resolve this issue related to the Safety Connect system. Both of these programs provide the same free remedy to correct this issue with Safety Connect. Lexus recommends that customers have the free remedy performed before reactivating Safety Connect. Vehicles that had an active Safety Connect subscription on or after 10/1/2017 were included in Limited Service Campaign LSC KLG. Vehicles that did not have an active Safety Connect subscription on or after 10/1/2017 but are affected by this condition are included in this Customer Support Program (19LE05).

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated. Note: Lexus has initiated a Limited Service Campaign and a Customer Support Program to resolve this issue related to the Safety Connect system. Both of these programs provide the same free remedy to correct this issue with Safety Connect. Lexus recommends that customers have the free remedy performed before reactivating Safety Connect. Vehicles that had an active Safety Connect subscription on or after 10/1/2017 were included in Limited Service Campaign LSC KLG. Vehicles that did not have an active Safety Connect subscription on or after 10/1/2017 but are affected by this condition are included in this Customer Support Program (19LE05).

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated. Note: Lexus has initiated a Limited Service Campaign and a Customer Support Program to resolve this issue related to the Safety Connect system. Both of these programs provide the same free remedy to correct this issue with Safety Connect. Lexus recommends that customers have the free remedy performed before reactivating Safety Connect. Vehicles that had an active Safety Connect subscription on or after 10/1/2017 were included in Limited Service Campaign LSC KLG. Vehicles that did not have an active Safety Connect subscription on or after 10/1/2017 but are affected by this condition are included in this Customer Support Program (19LE05).

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated. Note: Lexus has initiated a Limited Service Campaign and a Customer Support Program to resolve this issue related to the Safety Connect system. Both of these programs provide the same free remedy to correct this issue with Safety Connect. Lexus recommends that customers have the free remedy performed before reactivating Safety Connect. Vehicles that had an active Safety Connect subscription on or after 10/1/2017 were included in Limited Service Campaign LSC KLG. Vehicles that did not have an active Safety Connect subscription on or after 10/1/2017 but are affected by this condition are included in this Customer Support Program (19LE05).

The Data Communication Module (DCM) in the subject vehicles are equipped with software to identify the location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system?s features is activated.

intermittent MIL ON condition with Diagnostic Trouble Code (DTC) B1000 (Center Airbag Sensor Assembly Malfunction) stored in the history. This condition does not affect the proper operation of the Supplemental Restraint System (SRS). The SRS Electronic Control Unit (ECU) logic has been modified to reduce the possibility of this condition occurring. Follow the Repair Procedure in this bulletin to address this condition.

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver's side, and if applicable, passenger's side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver?s side and, if applicable, passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does NOT provide warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain specified State of Charge (SOC) of the vehicle?s battery while in stock and assure proper State of Charge (SOC) at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, all dealers should check battery State of Charge (SOC) and recharge, if necessary, within 48 hours of delivery to customers.

Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.

doors or remote start the vehicle.

The Repair Procedure section, Required Tools & Equipment section, and the Repair Procedure section has been updated. Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver's side, and if applicable, passenger's side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

intermittent MIL ?ON? condition with Diagnostic Trouble Code (DTC) B1000 (Center Airbag Sensor Assembly Malfunction) stored in the history. This condition does not affect the proper operation of the Supplemental Restraint System (SRS). The SRS Electronic Control Unit (ECU) logic has been modified to reduce the possibility of this condition occurring.

If installed, the driver's floor mat is too wide and cannot be secured in the correct position using the retaining clips.

If installed, the driver's floor mat is too wide and cannot be secured in the correct position using the retaining clips.

If installed, the driver's floor mat is too wide and cannot be secured in the correct position using the retaining clips.

IN ADDITION, SOME MODELS MAY UTILIZE RETAINING CLIPS FOR PASSENGER SIDE AND REAR SEAT FLOOR MATS AS WELL. FOLLOW THE APPROPRIATE INSTALLATION PROCEDURE TO ATTACH THE DRIVERS SIDE AND, IF APPLICABLE, PASSENGERS SIDE AND REAR SEAT FLOOR MATS TO THE VEHICLE CARPET USING THE FLOOR MAT RETAINING CLIPS DURING PRE-DELIVERY SERVICE (PDS).

THESE CONDITIONS INCLUDE STORAGE PERIOD, TEMPERATURE, PARASITIC DRAIN, AND BATTERY LOAD. BECAUSE OF THESE FACTORS, BATTERY INSPECTION AND MAINTENANCE ARE REQUIRED IN ORDER TO ENSURE PROPER OPERATION AND OPTIMAL BATTERY LIFE. AS A MATTER OF POLICY, TOYOTA DOES NOT PROVIDE WARRANTY COVERAGE FOR DISCHARGED AND/OR FAILED BATTERIES DUE TO LACK OF MAINTENANCE. IT IS THE DEALERS RESPONSIBILITY TO MAINTAIN SPECIFIED STATE OF CHARGE (SOC) OF THE VEHICLES BATTERY WHILE IN STOCK AND ASSURE PROPER STATE OF CHARGE (SOC) AT DELIVERY. TO ELIMINATE CUSTOMER SERVICE CONCERNS DUE TO AN UNDERCHARGED BATTERY DURING THE FIRST FEW WEEKS OF OWNERSHIP, ALL DEALERS SHOULD CHECK BATTERY STATE OF CHARGE (SOC) AND RECHARGE, IF NECESSARY, WITHIN 48 HOURS OF DELIVERY TO CUSTOMERS. "

IF INSTALLED, THE DRIVERS FLOOR MAT IS TOO WIDE AND CANNOT BE SECURED IN THE CORRECT POSITION USING THE RETAINING CLIPS.

IF INSTALLED, THE DRIVERS FLOOR MAT IS TOO WIDE AND CANNOT BE SECURED IN THE CORRECT POSITION USING THE RETAINING CLIPS.

IF INSTALLED, THE DRIVERS FLOOR MAT IS TOO WIDE AND CANNOT BE SECURED IN THE CORRECT POSITION USING THE RETAINING CLIPS.

A BATTERY IN A STORED VEHICLE IS SUBJECT TO CONDITIONS THAT CAN REDUCE ITS PERFORMANCE AND LIFE. THESE CONDITIONS INCLUDE STORAGE PERIOD, TEMPERATURE, PARASITIC DRAIN, AND BATTERY LOAD. BECAUSE OF THESE FACTORS, BATTERY INSPECTION AND MAINTENANCE ARE REQUIRED IN ORDER TO ENSURE PROPER OPERATION AND OPTIMAL BATTERY LIFE.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address this condition.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address this condition.

L-SB-0074-14. ? The Part Information and Required Tools & Equipment, and On-Vehicle Data Navigation Update sections have been updated. Service Bulletin No. L-SB-0074-14 is obsolete and any printed versions should be discarded. Lexus models equipped with the HDD Navigation (EMV-N) system require a Special Service Tool (SST) USB drive to update the map, points of interest, Gracenote, and system software. The SST is used with all vehicles to deliver the update; however, a unique activation number is required for each vehicle. Activation numbers are provided in an Activation Card Number pamphlet available through the normal parts ordering system. Use the process described in this bulletin to perform the update.

1. First type is generation 6 or 7 which utilizes HDD (Hard Disc Drive). Pioneer models that begin with NXH, have map data, operating system and other information in the Hard Disc Drive. With this system if a radio is being sent back for an exchange. The original Hard Disc Drive needs to be removed and installed into the newly serviced radio.

L-SB-0035-15. ? The entire bulletin has been updated. Service Bulletin No. L-SB-0035-15 is obsolete and any printed versions should be discarded. Some 2015 ? 2017 model year Lexus vehicles equipped with navigation (version older than V1##8940) may exhibit one or more of the following conditions: ? Unable to download Destination Assist ? Software update date does not display ? ?Calculating? message displays on the map screen without displaying street name and remaining distance ? Unable to guide a route on the Home screen ? Black display screen ? Bluetooth disconnects intermittently. Some 2015 ? 2016 model year Lexus vehicles equipped with navigation (version older than V1##8910) may exhibit one or more of the following conditions: ? Inoperative Voice Recognition ? Same XM channel icon is used for different channels ? Loss of traffic information intermittently when using Lexus Enform ? Traffic incident mark ?!? on the map screen but no information on the traffic incident screen ? iPod scroll is stopped changing by tune knob ? Inoperative Home button ? Reset occurs while making a turn off the highlighted route ? After correction of text in Quick Message15, the corrected text displays in Quick Message13 ? Navigation system reboots intermittently ? Navigation system reboots after receiving errant weather data ? Some screens with clock information display ?12:00? as ?0:00? S

the first time on new vehicles. The download and installation process may also be performed under other circumstances such as following a head unit replacement or after the customer's personal settings are erased. The download and installation process requires between 3 and 15 minutes to complete, depending on file size, cellular connection speed, and other factors. Following the download and installation procedure, individual Enform apps may periodically update through an over-the-air update system. Follow the procedure in this bulletin to perform the download/installation procedure and app updates.

(This condition may be due to an errant data broadcast by Toyota's traffic and weather data service provider.) Follow the process in this bulletin to reset the navigation system.

As part of the Pre-Delivery Service (PDS) process, ensure that the XM Satellite Radio is activated and ready for use.

As part of the Pre-Delivery Service (PDS) process, ensure that the XM Satellite Radio is activated and ready for use.

equipped with navigation (version less than V1##8910), may exhibit one or more of the following conditions: * Voice Recognition is inoperative * Same XM channel icon is used for different channels * Loss of traffic information at times when using Lexus Enform * There is traffic incident mark "!" on the map screen, but no info on the traffic incident screen * iPod scroll is stopped changing by tune knob * After correction of text in Quick Message15, the corrected text is displayed in Quick Message13 * Navigation system reboots intermittently * Navigation system reboots after receiving errant weather data * Some screens with clock information show 12:00 as 0:00 Some 2015 Lexus CT 200h, IS, NX, ES, RC, GS, and LS models equipped with navigation (version less than V1##8872), or GX 460 vehicles equipped with navigation (version less than V1##8871) may exhibit one or more of the following conditions: * Navigation system becomes frozen/has no response or slow response * Missing or incorrect HD Traffic incidents and/or flow data shown on the screen * Resetting of the navigation system * iPod Error is displayed with Apple device connected to the USB port * Song Title is not updated when using Siri * Display is blank after a Bluetooth? Audio device is connected * No audio sound after completing a phone call * Navigation system resets when playing an "Audio Book" on a CD * Unable to load multiple destinations when using destination Assist feature * HOME button does not work * Reset while making a turn off of the highlighted route

system with Android phones OS 4.4 or later. This condition tends to occur to customers who have many previous text messages on their phones.

As part of the Pre-Delivery Service (PDS) process, ensure that the XM Satellite Radio is activated and ready for use.

memory.

1. First type is generation 6 or 7 which utilizes HDD (Hard Disc Drive). Pioneer models that begin with NXH, have Map Data, Operating System and other Information in the Hard Disc Drive. With this system if a radio is being sent back for an exchange. The original Hard Disc Drive needs to be removed and installed into the newly serviced radio. 2. The Second type is Generation 8 Navigation system which utilizes the Micro SD Card. Pioneer models that begin with NXF, have map data in the Micro SD card. This is a customer accessible Micro SD card which can be found behind the front flip cover. The original Micro SD card should be removed and installed into the newly serviced radio.

system with Android phones OS 4.4 or later. This condition tends to occur to customers who have many previous text messages on their phones.

are used for the first time on new vehicles. The download and installation process may also need to be performed under other circumstances such as following a head unit replacement or after the customer's personal settings are erased. The download and installation process requires between 3 and 15 minutes to complete, depending on the file size, cellular connection speed, and other factors. Following the download and installation process, small Enform? App updates may also occur via an over the air update system. Follow the procedure below to perform the download and installation process.

SYSTEM WITH ANDROID PHONES OS 4.4 OR LATER. THIS CONDITION TENDS TO OCCUR TO CUSTOMERS WHO HAVE MANY PREVIOUS TEXT MESSAGES ON THEIR PHONES.

ARE USED FOR THE FIRST TIME ON NEW VEHICLES. THE DOWNLOAD AND INSTALLATION PROCESS MAY ALSO NEED TO BE PERFORMED UNDER OTHER CIRCUMSTANCES SUCH AS FOLLOWING A HEAD UNIT REPLACEMENT OR AFTER THE CUSTOMER'S PERSONAL SETTINGS ARE ERASED. THE DOWNLOAD AND INSTALLATION PROCESS REQUIRES BETWEEN 3 AND 15 MINUTES TO COMPLETE, DEPENDING ON THE FILE SIZE, CELLULAR CONNECTION SPEED, AND OTHER FACTORS. FOLLOWING THE DOWNLOAD AND INSTALLATION PROCESS, SMALL ENFORM APP UPDATES MAY ALSO OCCUR VIA AN OVER THE AIR UPDATE SYSTEM. FOLLOW THE PROCEDURE BELOW TO PERFORM THE DOWNLOAD AND INSTALLATION PROCESS.

AS PART OF THE PRE-DELIVERY SERVICE (PDS) PROCESS, ENSURE THAT THE XM SATELLITE RADIO IS ACTIVATED AND READY FOR USE.

(THIS CONDITION MAY BE DUE TO AN ERRANT DATA BROADCAST BY TOYOTA'S TRAFFIC AND WEATHER DATA SERVICE PROVIDER.) FOLLOW THE PROCESS IN THIS BULLETIN TO RESET THE NAVIGATION SYSTEM.

Please see L-SB-0008-20. Replacement Certification Labels and VIN Plates

Please see L-SB-0003-20.

Please see L-SB-0017-19.

established, vehicle settings and/or network/cellular coverage concerns.

This condition has been remedied, and DCM activation utilizing Techstream can now be resumed.

This is a known condition and will be remedied in the near future. Please discontinue DCM activations utilizing Techstream until further notice.

Please see L-SB-0006-18.

Please see L-SB-0001-18.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

handle is repeatedly used with high force. If this occurs, the inside door handle can become inoperative.

L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003-93, PG002-90, L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003 93, and PG002-90. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1990 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

This condition may cause the door cable to become frozen and inoperable in freezing conditions. Follow the Repair Procedure in this bulletin to address this condition.

placed in the luggage compartment of the vehicle at the assembly plant. For states that require a front license plate, install the bracket and bolts on the bumper cover during Pre-Delivery Service (PDS) according to the following procedure. The RC 200t/300/350 (non-F Sport) models share the same installation procedure. The F Sport and F models require a different procedure (see page 4).

The door lock can be placed in the middle position between lock and unlock when exiting the vehicle. This can cause the door lock to be inoperative. APPLICABLE WARRANTY: This repair is covered under the Lexus Basic Warranty. This warranty is in effect for 48 months or 50,000 miles, whichever occurs first, from the vehicle's in-service date. Warranty application is limited to occurrence of the specified condition described in this bulletin.

vehicle.

vehicle.

L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003-93, and PG002-90. Service Bulletin Nos. L-SB-0048-08, PG007-07, PG016-01, PG015-01, PG004-97, PG003-97, PG003-93, and PG002-90 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Vehicle replacement certification labels (vinyl label installed on driver door or door post) and VIN lates (metal plate riveted to dashboard) may be available from Lexus, provided the request meets one of the criteria listed in this Service Bulletin.

vehicle.

Some 2014 ? 2016 model year Lexus vehicles may not unlock with either the Smart Entry or the wireless remote. The door lock can be placed in the middle position between lock and unlock when exiting the vehicle. This can cause the door lock to be inoperative.

? February 11, 2015 Rev1: Applicability has been updated to include 2006 ? 2015 model year Lexus vehicles. On some vehicles, when Rapgard? is removed, the paint may have a stained appearance. These stains appear to be under the clear coat. The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture. Use the following procedure to address this condition.

inoperative or the back door latch does not release, with Diagnostic Trouble Code (DTC) B2250 "Back Door Closer Malfunction" or DTC B2250 and DTC B2251 "Back Door Closer Switch Malfunction" set. In some cases, this condition may be associated with cold weather. Follow the Repair Procedure in this bulletin to address this condition.

PLACED IN THE LUGGAGE COMPARTMENT OF THE VEHICLE AT THE ASSEMBLY PLANT. FOR STATES THAT REQUIRE A FRONT LICENSE PLATE, INSTALL THE BRACKET AND BOLTS ON THE BUMPER COVER DURING PRE-DELIVERY SERVICE (PDS) ACCORDING TO THE FOLLOWING PROCEDURE. THE RC 200T/300/350 (NON-F SPORT) MODELS SHARE THE SAME INSTALLATION PROCEDURE. THE F SPORT AND F MODELS REQUIRE A DIFFERENT PROCEDURE (SEE PAGE 4)."

VEHICLE.

inconsistent air temperature coming from the air conditioner (A/C) vents, air not coming out at the selected temperature, and/or air not coming out of the selected A/C vent of the vehicle. Although the A/C servo motors are covered by Lexus? New Vehicle Limited Warranty for 4 years or 50,000 miles (whichever comes first), we at Lexus care about the customers? ownership experience. Lexus is providing coverage for repairs related to A/C servo motor(s) that have an internal electrical malfunction which could lead to the symptoms described above.

?Uneven temperature or air flow between the vents. ?Little or no air flow from the vent(s). ?Improper MODE control function. Additionally, some vehicles may store one or more of the following HVAC servo Diagnostic Trouble Codes (DTCs). ?B1441 ? Air Mix Damper Control Servo Motor Circuit (Front Passenger Side Lower Air Mix). ?B1442 ? Air Inlet Damper Control Servo Motor Circuit. ?B1443 ? Air Outlet Damper Control Servo Motor Circuit. ?B1446 ? Air Mix Damper Control Servo Motor Circuit (Driver Side Lower Air Mix). ?B1447 ? Rear Air Mix Damper Control Servo Motor Circuit. ?B1448 ? Passenger Side Face Servo Motor Circuit. ?B1449 ? Rear Air Outlet Damper Control Servo Motor Circuit. ?B1453 ? Driver Side Air Outlet Damper COOL Control Servo Motor Circuit. ?B1454 ? Passenger Side Air Outlet Damper COOL Control Servo Motor Circuit. ?B1455 ? Driver Side Air Outlet Damper FOOT/DEF Control Servo Motor Circuit. Follow the procedures in this bulletin to address this condition.

?Uneven temperature or air flow between the vents ?Little or no air flow from the vent(s) ?Improper MODE control function Additionally, some vehicles may store one or more of the following HVAC servo Diagnostic Trouble Codes (DTCs). ?B1441 ? Air Mix Damper Control Servo Motor Circuit (Front Passenger Side Lower Air Mix) ?B1442 ? Air Inlet Damper Control Servo Motor Circuit ?B1443 ? Air Outlet Damper Control Servo Motor Circuit ?B1446 ? Air Mix Damper Control Servo Motor Circuit (Driver Side Lower Air Mix) ?B1447 ? Rear Air Mix Damper Control Servo Motor Circuit ?B1448 ? Passenger Side Face Servo Motor Circuit ?B1449 ? Rear Air Outlet Damper Control Servo Motor Circuit ?B1453 ? Driver Side Air Outlet Damper COOL Control Servo Motor Circuit ?B1454 ? Passenger Side Air Outlet Damper COOL Control Servo Motor Circuit ?B1455 ? Driver Side Air Outlet Damper FOOT/DEF Control Servo Motor Circuit Follow the procedure in this bulletin to address this condition.

inconsistent air temperature coming from the air conditioner (A/C) vents, air not coming out at the selected temperature, and/or air not coming out of the selected A/C vent of the vehicle. Although the A/C servo motors are covered by Lexus? New Vehicle Limited Warranty for 4 years or 50,000 miles (whichever comes first), we at Lexus care about the customers? ownership experience. Lexus is providing coverage for repairs related to A/C servo motor(s) that have an internal electrical malfunction which could lead to the symptoms described above.

inconsistent air temperature coming from the air conditioner (A/C) vents, air not coming out at the selected temperature, and/or air not coming out of the selected A/C vent of the vehicle. Although the A/C servo motors are covered by Lexus? New Vehicle Limited Warranty for 4 years or 50,000 miles (whichever comes first), we at Lexus care about the customers? ownership experience. Lexus is providing coverage for repairs related to A/C servo motor(s) that have an internal electrical malfunction which could lead to the symptoms described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

Follow the Repair Procedure in this bulletin to address this condition.

rattle/knocking noise condition at idle from the driver floor board area due to fuel line contact with the body. Follow the Repair Procedure in this bulletin to address this condition.

feeling (back and forth jerking that comes right after a shift but then dissipates quickly after 1 ? 2 and/or 2 ? 3 upshifts) ? A surge feeling (back and forth rocking that is not associated with transmission shifts) when the vehicle is traveling between 0 ? 46 mph, transmission is in 3rd ? 8th gear, and torque converter is in full lock-up The Engine Control Module/ECM (SAE Term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of these conditions. Follow the Repair Procedure in this bulletin to address these conditions.

L-SB-0021-14. G1765 Applicability has been updated to include applicable 2018 models and 2016 ? 2018 model year RC 300 and 2015 ? 2018 model year RC 350 vehicles. ? Applicability has been updated to exclude 2001 ? 2003 model year ES 300 vehicles. Service Bulletin No. L-SB-0021-14 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines the use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Lexus term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ECU is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Lexus-specific control unit

injectors manually on 2GR-FKS engines. When direct injection is started and then stopped using the active test, current ECU logic does not turn off the direct injectors and can cause DTCs P017200, P017500 and P0160300. To avoid this condition, technicians should raise engine RPM when changing back and forth between the Direct Injection and Port Injection active tests. Use the recommended procedure below to avoid this concern while testing injection mode of FKS equipped vehicles. NOTE: If the active test is used multiple times without using this procedure to raise engine RPM, it may be necessary to reset learning values for fuel trim and Air to Fuel ratio before returning vehicle to customer.

plant and temporarily stored in the blank space of the relay block in the engine compartment. During Pre-Delivery Service (PDS), reinstall the D/C Cut fuse into its original location.

Follow the Repair Procedure in this bulletin to address this condition.

Follow the Repair Procedure in this bulletin to address this condition.

L-SB-0021-14. * Applicability has been updated to include applicable 2018 models and 2016 * 2018 model year RC 300 and 2015 * 2018 model year RC 350 vehicles. * Applicability has been updated to exclude 2001 - 2003 model year ES 300 vehicles. Service Bulletin No. L-SB-0021-14 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines the use of TIS and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Lexus term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ECU is used as a generic label for the following SAE J1930 standard references: * Powertrain Control Module (PCM) * Engine Control Module (ECM) * Transmission Control Module (TCM) * Any other Lexus-specific control unit

(Engine Off Timer Performance) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module [PCM]) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure below to address this condition.

PLANT AND TEMPORARILY STORED IN THE BLANK SPACE OF THE RELAY BLOCK IN THE ENGINE COMPARTMENT. DURING PRE-DELIVERY SERVICE (PDS), REINSTALL THE D/C CUT FUSE INTO ITS ORIGINAL LOCATION."

For customers who find this characteristic objectionable, an updated shim kit is now available as a service part.

This is only applicable on 2WD F Sport vehicles. This condition may be present at city, highway, and/or parking lot speeds. For customers who find this characteristic objectionable, an updated front brake pad kit is available.

This is only applicable on 2WD F Sport vehicles. This condition may be present at city, highway, and/or parking lot speeds. For customers who find this characteristic objectionable, an updated front brake pad kit is available.

finishes may become discolored and/or damaged when aftermarket cleaners, polishes, or brake dust removal products are used on wheels with super chrome finishes. Wheel cleaners and polish that contain acidic substances may damage the clear coat of the wheel, resulting in the undercoating (black) to become visible. See Figures 1 and 2 below for examples of wheel finishes damaged by aftermarket products. NOTE If using a wheel cleaning product, first test it in an area NOT visible to the customer.

Wheel offset, defined as the distance between the wheel?s centerline and the wheel-to-rotor mounting surface, affects the clearance between the back of the wheel and surrounding brake components (Figure 1). Installation of a wheel with an offset or width different than the correct specification, such as installing the rear wheel on the front, can cause damage to brake components due to interference between the wheel and adjacent parts. The wheel could contact the brake caliper thereby introducing stress into the caliper, brake rotor, and potentially other components. In some cases, this stress could contribute to cracking or separation of the brake rotor.

Some applicable vehicles have had front rotors replaced for a clicking concern, see L-SB-0100-16.

For customers who find this characteristic objectionable, an updated shim kit is now available as a service part.

even one lug nut over or under torqued, can cause a vibration issue * When lug nuts are over torqued, this causes the rotor to have a runout out condition which can lead to brake vibration concerns * Brake vibration issues can occur at parking lot to highway speeds * Brake vibration issues can occur at light to moderate braking * Tightening lug nuts in a star pattern method during the torqueing process will assure that even/equal pressure is applied across the rotor hub surface * Torque sticks/wrenches should be used to apply accurate torque values when tightening * Do Not use impact guns/ratchets to completely run lug nuts up to the wheel surface

Service parts are now available to reduce the likelihood of this condition occurring. The backing plates of the brake pads have been covered with an anti-rust coating to address the brake pads sliding in the caliper assembly and reduce RTV (rotor thickness variation). Follow the Repair Procedure in this bulletin to address this condition.

The condition can occur at any time if improper torque is applied to lug nuts. Over time, even one lug nut over- or under-torqued can cause a vibration condition. When lug nuts are over-torqued, this causes the rotor to have a runout condition, which can lead to brake vibration conditions.

Screws) is loaded in the luggage compartment at the assembly plant to avoid damage in transit. Install the front wheel opening extension pads on the vehicle during Pre-Delivery Service (PDS).

SCREWS) IS LOADED IN THE LUGGAGE COMPARTMENT AT THE ASSEMBLY PLANT TO AVOID DAMAGE IN TRANSIT. INSTALL THE FRONT WHEEL OPENING EXTENSION PADS ON THE VEHICLE DURING PRE-DELIVERY SERVICE (PDS).

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

temperature difference between the driver and/or passenger seats. Follow the Repair Procedure in this bulletin to address this condition.

Adding stop leak products to the A/C system is not a recommended or approved Lexus repair process. During A/C service, moisture enters the A/C system, and can react with the previously added A/C stop leak, forming a gelatinous substance. The gel substance that forms can cause the A/C compressor to bind and or seize.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

The settlement includes Lexus?s agreement to provide a Customer Support Program for certain 2015-2020 model year (MY) vehicles that were not previously involved in a Safety Recall or Special Service Campaign related to the low pressure fuel pump. The purpose of this Customer Support Program letter is to help clarify how to administer this coverage in accordance with the settlement.

following Diagnostic Trouble Codes (DTCs): ?DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ?DTC P0087 Fuel Rail / System Pressure ? Too Low Techstream data list analysis may reveal positive fuel trims including a no pressure condition verified by a manual fuel pressure gauge. Follow the Repair Procedure in this bulletin to address these conditions.

These reports have indicated there is a possibility that the inside door handles can break where the latch release cable is attached if the handle is repeatedly used with high force. If this occurs, the inside door handle can become inoperative. Although the rear inside door handles are covered by Lexus? New Vehicle Limited Warranty for 4 years or 50,000 miles (whichever comes first), we at Lexus care about the customers? ownership experience. Lexus is providing coverage for repairs related to the rear inside door handle becoming inoperative. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part. NOTE The ARINIX Tip is NOT registered or labeled for sale or use outside the United States or Puerto Rico.

Countermeasure parts are available to reduce the droning noise. Follow the Repair Procedure in this bulletin to address this condition.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage and affect a vehicle's systems and components. Any problems that are found should be corrected immediately.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle's systems and components. Any problems that are found should be corrected immediately.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle's systems and components. Any problems that are found should be corrected immediately.

In the event that injector seal repair is required on vehicles equipped with a direct injection fuel system, a Special Service Tool Set is required to properly install the seal onto the injector. As new vehicle configurations have been released, several injector seal tool sets have been distributed to accommodate these new vehicles. There are a total of three injector seal tool sets for Lexus models, located in the appropriate SST cabinets. Each kit contains multiple pieces as shown in the diagram below. The individual pieces must remain together to ensure these tools are used correctly. Refer to the repair manual for the tool information to ensure the correct tool is used for the desired application.

THE FOLLOWING GUIDELINES SHOULD BE PERFORMED TO MINIMIZE VEHICLE COMPONENT/PART DEGRADATION DUE TO EXTENDED VEHICLE STORAGE CONDITIONS. LONG-TERM STORAGE AND AFFECT A VEHICLE'S SYSTEMS AND COMPONENTS. ANY PROBLEMS THAT ARE FOUND SHOULD BE CORRECTED IMMEDIATELY.

VEHICLE LOCATION INACCURATE

Vehicles were moved from Customer Support Program 19LE05 and added to Limited Service Campaign KLG.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

ST004-01, SU001-08, and L-SB-0174-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Lexus vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

connectivity concerns such as: Difficulty to pair the phone. Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. Various Bluetooth Audio functions are no longer functioning with the customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.

INTERMITTENT BLUETOOTH FAILURE TO CONNECT TO THE VEHICLE WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMER'S PHONE SUCH AS ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMER'S PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY.

noise from the front wheel area during slow (parking lot) speed turns. The clicking noise that can be heard during sharp turns is a normal condition for certain vehicles originally equipped with a lightweight two-piece aluminum rotor assembly. For customers who find this objectionable, an alternative steel rotor is available. Before performing the repair in this bulletin, it is recommended to review the visual differences of the steel rotor with the customer.

noise from the front wheel area during slow (parking lot) speed turns. The clicking noise that can be heard during sharp turns is a normal condition for certain vehicles originally equipped with a lightweight two-piece aluminum rotor assembly. For customers who find this objectionable, an alternative steel rotor is available. Before performing the repair in this bulletin, it is recommended to review the visual differences of the steel rotor with the customer.

Any previous printed versions of this bulletin should be discarded. Some 2013 ? 2019 model year Lexus vehicles equipped with 2WD drivetrain and the F Sport package may exhibit a clicking noise from the front wheel area during a slow (parking lot) speed turn. Follow the Repair Procedure in this bulletin to address this condition.

drivetrain may exhibit a clicking type noise from the front wheel area during a slow (parking lot) speed turn. Follow the procedures in this bulletin to address the condition.

package may exhibit a clicking type noise coming from the front wheel area during a slow (parking lot) speed turn. Follow the Repair Procedure in this bulletin to address this condition.

Some 2013 - 2017 model year GS 350/450h, 2015 - 2017 model year RC 200t/350 and 2016 - 2017 model year GS 200t vehicles equipped with 2WD drivetrain and the F Sport package may exhibit a clicking type noise coming from the front wheel area during a slow (parking lot) speed turn. Follow the Repair Procedure in this bulletin to address this condition.

DRIVETRAIN MAY EXHIBIT A CLICKING TYPE NOISE FROM THE FRONT WHEEL AREA DURING A SLOW (PARKING LOT) SPEED TURN. FOLLOW THE PROCEDURES IN THIS BULLETIN TO ADDRESS THE CONDITION.

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Lexus.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Please refer to the following procedure to ensure that the original tires stay in the same location on the vehicle.

If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Please refer to the following procedure to ensure that the original tires stay in the same location on the vehicle.

If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Please refer to the following procedure to ensure that the original tires stay in the same location on the vehicle.

IF THE WHEELS ARE REPLACED OR REFINISHED BEFORE VEHICLE DELIVERY, IT IS IMPORTANT THAT THE TIRES REMAIN ON THE VEHICLE IN THE SAME LOCATION AND IN THE SAME DIRECTION OF ROTATION. PLEASE REFER TO THE FOLLOWING PROCEDURE TO ENSURE THAT THE ORIGINAL TIRES STAY IN THE SAME LOCATION ON THE VEHICLE. "

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner's Manual will highlight the importance of proper maintenance and provide guidance for care.

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care. NOTE Leather seat covers that are replaced for dye transfer or soiling are NOT eligible for replacement under warranty. Likewise, damage caused by unapproved cleaning methods are NOT eligible for replacement under warranty.

AS AN ADDITIONAL RESOURCE, IF THE VEHICLE IS EQUIPPED WITH FACTORY LEATHER SEATS, THE VEHICLE OWNER'S MANUAL WILL HIGHLIGHT THE IMPORTANCE OF PROPER MAINTENANCE AND PROVIDE GUIDANCE FOR CARE.

GX 460, IS 300/350/200t, NX 200t/300h, and RC F/350/300/200t vehicles. Any previous printed versions of this bulletin should be discarded.

This condition may be more noticeable in colder ambient temperatures and may occur when traveling over uneven roads or when the vehicle comes to a complete stop. Follow the Repair Procedure in this bulletin to address this condition. APPLICABLE WARRANTY ? This repair is covered under the Lexus Basic Warranty. This warranty is in effect for 48 months or 50,000 miles, whichever occurs first, from the vehicle?s in-service date. ? Warranty application is limited to occurrence of the specified condition described in this bulletin.