2016 Land Rover Range Rover Sport TSBs

incorrectly changed for knock issues when the front bush is cracked and should have been replaced as per Technical Service Bulletins LTB00204v4 and LTB00123v4.

There is a hesitation. The Check Engine MIL goes on and off. There is a noise on startup.

Customer may have a hesitation concern but this is not in every case.

Engine MIL illuminated with one of the following DTCs stored in the PCM. P228F-85 P025C-11 P0251-13 P064A-38 P0256-13

Any of the following DTCs (indicating an air intake system leak) could be stored in the Powertrain Control Module (PCM) ? P2187, P2189, P0505, P0507.

DTCs vary, may include P2187-00, P2189-00, P013E-00,P014E-00. Fuel trims near limit when engine is at idle speed.

flashing (see attachment) with engine off

flashing (see attachment) with engine off

Diagnostic Trouble Code (DTC) B1B87-31, stored in Driver Seat Module (DSM) or Passenger Seat Module (PSM) Note that the seat height motor is supplied as part of the cushion sub-assembly or motor sub-assembly (depending on model)

flashing (see attachment) with engine off

flashing (see attachment) with engine off

Diagnostic Trouble Code (DTC) B1B87-31, stored in Driver Seat Module (DSM) or Passenger Seat Module (PSM) Note that the seat height motor is supplied as part of the cushion sub-assembly or motor sub-assembly (depending on model)

flashing (see attachment) with engine off

flashing (see attachment) with engine off

Trouble Code) P0234-77 stored in the Powertrain Control Module (PCM). DTC P2463-00 and P246B-00 may also be stored.

The noise is most prominent during light throttle and low speed (for example: during car park maneuvers) and is independent of ambient temperature range. Under these conditions, a low-level, non-constant cyclical-type noise can be heard coming from the Center Exhaust system (Exhaust Valve) adjacent to the fuel tank.

Engineering would like to investigate the root cause as to these concerns

They may not be able to release the EPB for a short period of time following this message The following 4 DTC?s will be logged within the Anti-lock Brake System (ABS) module: C2005-71 - Right actuator ? Actuator Stuck C2006-71 - Left actuator ? Actuator Stuck C2007-72 ? Right Motor ? Actuator Stuck open C2008-72 - Left Motor ? Actuator Stuck open

Engineering would like to investigate the root cause as to these concerns

They may not be able to release the EPB for a short period of time following this message The following 4 DTC?s will be logged within the Anti-lock Brake System (ABS) module: C2005-71 - Right actuator ? Actuator Stuck C2006-71 - Left actuator ? Actuator Stuck C2007-72 ? Right Motor ? Actuator Stuck open C2008-72 - Left Motor ? Actuator Stuck open

They may not be able to release the EPB for a short period of time following this message The following 4 DTC?s will be logged within the Anti-lock Brake System (ABS) module: C2005-71 - Right actuator ? Actuator Stuck C2006-71 - Left actuator ? Actuator Stuck C2007-72 ? Right Motor ? Actuator Stuck open C2008-72 - Left Motor ? Actuator Stuck open

seam.

Upon further investigation, DTC (Diagnostic Trouble Code) P0299-77 is stored in the Powertrain Control Module (PCM).

housing seam.

The noise is most prominent during light throttle and low speed, for example during car park maneuvers and is independent of ambient temperature range. Under these conditions, a low-level non-constant cyclical-type noise can be heard coming from the Center Exhaust system (Exhaust Valve) adjacent to the fuel tank.

The sound may be noticeable, when one of the front wheels travels over a uneven surface while the opposite front wheel remains on a smooth surface.

P2251-13 stored in the Powertrain Control Module (PCM).

They may not be able to release the EPB for a short period of time following this message The following 4 DTC?s will be logged within the Anti-lock Brake System (ABS) module: C2005-71 - Right actuator ? Actuator Stuck, C2006-71 - Left actuator ? Actuator Stuck, C2007-72 ? Right Motor ? Actuator Stuck open, C2008-72 - Left Motor ? Actuator Stuck open

Upon further diagnosis, the Technician may find DTC (Diagnostic Trouble Code) P0089-64 and/or P0089-92 stored in the Powertrain Control Module (PCM).

message will not appear on the Instrument Cluster (IC) if a vehicle has reached its service point and the engine is started normally by pressing the engine START/STOP button with the brake pedal pressed. Turning on the ignition only, by pressing the engine START/STOP button without the brake pedal pressed, will still allow the 'Service Required' warning message to be displayed.

Trouble Code) P132B-77 stored in the Powertrain Control Module (PCM).

isolation.

(DTC) P0234-77 stored in the Powertrain Control Module (PCM). DTCs P2463-00 and P246B-00 may also be stored.

housing seam.

The noise is most prominent during light throttle and low speed, for example during car park maneuvers and is independent of ambient temperature range. Under these conditions, a low-level non-constant cyclical-type noise can be heard coming from the Center Exhaust system (Exhaust Valve) adjacent to the fuel tank.

The sound may be noticeable, when one of the front wheels travels over a uneven surface while the opposite front wheel remains on a smooth surface.

P2251-13 stored in the Powertrain Control Module (PCM).

They may not be able to release the EPB for a short period of time following this message The following 4 DTC?s will be logged within the Anti-lock Brake System (ABS) module: C2005-71 - Right actuator ? Actuator Stuck, C2006-71 - Left actuator ? Actuator Stuck, C2007-72 ? Right Motor ? Actuator Stuck open, C2008-72 - Left Motor ? Actuator Stuck open

Upon further diagnosis, the Technician may find DTC (Diagnostic Trouble Code) P0089-64 and/or P0089-92 stored in the Powertrain Control Module (PCM).

message will not appear on the Instrument Cluster (IC) if a vehicle has reached its service point and the engine is started normally by pressing the engine START/STOP button with the brake pedal pressed. Turning on the ignition only, by pressing the engine START/STOP button without the brake pedal pressed, will still allow the 'Service Required' warning message to be displayed.

Trouble Code) P132B-77 stored in the Powertrain Control Module (PCM).

isolation.

(DTC) P0234-77 stored in the Powertrain Control Module (PCM). DTCs P2463-00 and P246B-00 may also be stored.

P2455-22 stored in the Powertrain Control Module (PCM).

P2251-13 stored in the Powertrain Control Module (PCM).

leaks incorrectly being identified as coming from the rear transmission oil seal or sump. Oil weeps through the aluminium of the casing in the base of the pocket around where the steel D clutch tube is embedded, refer to attached file.

direct pressure sensing valve within the Air Conditioning (A/C) compressor becomes stuck and cannot respond to changing demands for A/C compressor displacement. The vehicle continues to operate; however, the function of the climate system is compromised by the failure mode. The customer may report a number of symptoms: cycling temperature within the passenger compartment, too cold, too hot, and/or odor ingress.

direct pressure sensing valve within the Air Conditioning (A/C) compressor becomes stuck and cannot respond to changing demands for A/C compressor displacement. The vehicle continues to operate; however, the function of the climate system is compromised by the failure mode. The customer may report a number of symptoms: cycling temperature within the passenger compartment, too cold, too hot, and/or odor ingress.

The CEL may be paired with DTC P2002-00 stored in the PCM for DPF Efficiency. Should any repairs be made on a vehicle with this issue, please submit an EPQR and retain all replaced parts. Engineering may call the parts back for further analysis.

Code (DTC) P132B-77 stored in the Powertrain Control Module (PCM).

message will not appear on the Instrument Cluster (IC) if a vehicle has reached its service point and the engine is started normally by pressing the engine START/STOP button with the brake pedal pressed. Turning on the ignition only, by pressing the engine START/STOP button without the brake pedal pressed, will still allow the 'Service Required' warning message to be displayed. In addition, the latest Powertrain Control Module (PCM) software has introduced a concern relating to the ability to reset the service message indicator. The latest IC software will rectify these concerns.

The sound may be noticeable, when one of the front wheels travels over a uneven surface while the opposite front wheel remains on a smooth surface.

message will not appear on the Instrument Cluster (IC) if a vehicle has reached its service point and the engine is started normally by pressing the engine START/STOP button with the brake pedal pressed. Turning on the ignition only, by pressing the engine START/STOP button without the brake pedal pressed, will still allow the 'Service Required' warning message to be displayed. In addition, Powertrain Control Module (PCM) software introduced a concern relating to the ability to reset the service message indicator. The latest IC software will rectify these concerns.

display the 'Service Required' message on the Instrument Cluster, when starting the engine by depressing the brake pedal and pressing the engine START/STOP button, if/when a vehicle has reached its service interval. The message will display when switching the ignition only 'ON' (engine ?OFF?) by pressing the engine START/STOP button and NOT depressing the brake pedal.

'Service Required' message on the Instrument Cluster, when starting the engine by depressing the brake pedal and pressing the engine START/STOP button, if/when a vehicle has reached its service interval. The message will display when switching the ignition only 'ON' (engine OFF) by pressing the engine START/STOP button and NOT depressing the brake pedal.

message will not appear on the Instrument Cluster (IC) if a vehicle has reached its service point and the engine is started normally by pressing the engine START/STOP button with the brake pedal pressed. Turning on the ignition only, by pressing the engine START/STOP button without the brake pedal pressed, will still allow the 'Service Required' warning message to be displayed. In addition, the latest Powertrain Control Module (PCM) software has introduced a concern relating to the ability to reset the service message indicator. The latest IC software will rectify these concerns.

This concern can be described as Shock/Clunk, Tip In Clonk. The concern is specific to vehicles fitted with Euro 5 AJ126 Supercharged engine only.

As the driving mode changes, the transmission may downshift, the engine Revolutions Per Minute (RPM) may also increase, and/or the 'Auto Stop/Start OFF' warning indicator may illuminate on the Instrument Cluster (IC).

display the 'Service Required' message on the Instrument Cluster, when starting the engine by depressing the brake pedal and pressing the engine START/STOP button, if/when a vehicle has reached its service interval. The message will display when switching the ignition only 'ON' (engine OFF) by pressing the engine START/STOP button and NOT depressing the brake pedal.

Incorrect Diesel Exhaust Fluid Quality Detected' warning message displayed on the Instrument Cluster. During diagnosis, the technician may find Diagnostic Trouble Code (DTC) P2BA9-00 and/or P2BA9-92, which may be accompanied by DTCs P2BAE and P2BAF, stored in the Powertrain Control Module (PCM).

Range which will not display the 'Service Required' message on the Instrument Cluster, when starting the engine by depressing the brake pedal and pressing the engine START/STOP button, if/when a vehicle has reached its service interval. The message will display when switching the ignition only 'ON' (engine ?OFF?) by pressing the engine START/STOP button and NOT depressing the brake pedal.

This can lead to Roadside Assistance being necessary.

stored in the Powertrain Control Module (PCM). DTC P2BAE and/or P2BAF may also be stored in the PCM.

difficulties with starting due to fuel supply issues to engine

'Incorrect Diesel Exhaust Fluid Quality Detected' warning message displayed within the Instrument Cluster (IC) and Diagnostic Trouble Code (DTC) P2BA9-00 and/or P2BA9-92 stored in the Powertrain Control Module (PCM) which may be accompanied by DTCs P2BAE and P2BAF.

The engine oil level sensor is being replaced and when returned and tested shows no fault. DTCs relevant to the engine oil level sensor (P250A-37 and/or P250A-38) / engine oil temperature sensor circuit (P0195-00) maybe stored in the Powertrain Control Module (PCM).

'Incorrect Diesel Exhaust Fluid Quality Detected' warning message displayed on the Instrument Cluster (IC) and Diagnostic Trouble Code (DTC) P2BA9-00 and/or P2BA9-92 stored in the Powertrain Control Module (PCM) which may be accompanied by DTCs P2BAE and P2BAF.

This can lead to Roadside Assistance being necessary.

stored in the Powertrain Control Module (PCM). DTC P2BAE and/or P2BAF may also be stored in the PCM.

of the emission control system of TDV6 3.0L diesel vehicles within the listed Affected Vehicle Range. Specifically, the key improvements comprise a number of revised driver instrument display messages. These include the status of the Diesel Exhaust Fluid (DEF) system as well as an optimized emission control strategy for the extended operation of the vehicle under demanding conditions such as sustained high-speed driving, aggressive acceleration, or heavy towing. As a result to this change, it is expected that customers of certain vehicles who regularly operate their vehicles under such conditions will experience a noticeable increase in the rate of consumption of DEF. An Owner?s Handbook Supplement for these vehicles (Range Rover Sport [L494; 519971-571257; 617562-643823] and Range Rover [L405; 219083-274090]) is also included in this program.

This may be accompanied by the warning message "No engine restarts in xxx miles, diesel exhaust fluid dosing malfunction? displayed in the Instrument Cluster message center and Diagnostic Trouble Code (DTC) P208B-00, as well as DTC P2BAE / P2BAF, stored in the Powertrain Control Module (PCM).

P205B-85, and/or P249C-00 stored in the Powertrain Control Module (PCM).

Range which will not display the 'Service Required' message on the Instrument Cluster, when starting the engine by depressing the brake pedal and pressing the engine START/STOP button, if/when a vehicle has reached its service interval. The message will display when switching the ignition only 'ON' (engine OFF) by pressing the engine START/STOP button and NOT depressing the brake pedal.

display the 'Service Required' message on the Instrument Cluster, when starting the engine by depressing the brake pedal and pressing the engine START/STOP button, if/when a vehicle has reached its service interval. The message will display when switching the ignition only 'ON' (engine OFF) by pressing the engine START/STOP button and NOT depressing the brake pedal.

Range which will not display the 'Service Required' message on the Instrument Cluster, when starting the engine by depressing the brake pedal and pressing the engine START/STOP button, if/when a vehicle has reached its service interval. The message will display when switching the ignition only 'ON' (engine ?OFF?) by pressing the engine START/STOP button and NOT depressing the brake pedal.

'Incorrect Diesel Exhaust Fluid Quality Detected' warning message displayed on the Instrument Cluster (IC) and Diagnostic Trouble Code (DTC) P2BA9-00 and/or P2BA9-92 stored in the Powertrain Control Module (PCM) which may be accompanied by DTCs P2BAE and P2BAF.

display the 'Service Required' message on the Instrument Cluster, when starting the engine by depressing the brake pedal and pressing the engine START/STOP button, if/when a vehicle has reached its service interval. The message will display when switching the ignition only 'ON' (engine OFF) by pressing the engine START/STOP button and NOT depressing the brake pedal.

This can lead to Roadside Assistance being necessary.

may not re-start and the ignition will turn off.

'Incorrect Diesel Exhaust Fluid Quality Detected' warning message displayed on the Instrument Cluster (IC) and Diagnostic Trouble Code (DTC) P2BA9-00 and/or P2BA9-92 stored in the Powertrain Control Module (PCM) which may be accompanied by DTCs P2BAE and P2BAF.

ENGINE COMPARTMENT."

LEAKS INCORRECTLY BEING IDENTIFIED AS COMING FROM THE REAR TRANSMISSION OIL SEAL OR SUMP.

STORED IN THE POWERTRAIN CONTROL MODULE (PCM). DTC P2BAE AND/OR P2BAF MAY ALSO BE STORED IN THE PCM.

TO AN EVAPORATIVE EMISSION (EVAP) FAULT STORED IN THE POWERTRAIN CONTROL MODULE (PCM).

(ECM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE.

UPON DIAGNOSIS, INCLUDING REMOVAL OF THE AIR SPRING AND INVERTING IT FOR A PERIOD OF APPROXIMATELY ONE MINUTE, HYDRAULIC FLUID IS FOUND TO FLOW FROM THE AIR SUSPENSION PIPE 'VOSS' CONNECTOR."

RESTARTS IN XXX MILES/KM, DIESEL EXHAUST FLUID DOSING MALFUNCTION WARNING MESSAGE DISPLAYED WITHIN THE INSTRUMENT CLUSTER MESSAGE CENTRE AND DTCS P20E8-84/85 AND P2BAE/P2BAF STORED IN THE PCM (POWERTRAIN CONTROL MODULE). NOTE: IF OTHER CODES ARE STORED IN THE PCM THEY MUST BE INVESTIGATED AND RESOLVED BEFORE FOLLOWING THE ADVICE DETAILED IN THIS SSM. CAUSE: THE SYSTEM HAS DETECTED A PRESSURE DEVIATION IN THE DEF (DIESEL EXHAUST FLUID) INJECTION SYSTEM."

STORED IN THE POWERTRAIN CONTROL MODULE (PCM) CAUSE: THIS MAY BE CAUSED BY A PCM SOFTWARE ISSUE (CPU RESPONSE TIME ERROR DURING VEHICLE SHUTDOWN PROCEDURE)."

NO DRIVEABILITY CONCERNS ARE OBSERVED BY THE CUSTOMER. ONE OR MORE CODES ARE STORED IN THE PCM RELATING TO THE 'HEATED OXYGEN SENSOR (HO2S) - POST CATALYST - BANK 1 (OR BANK 2) SENSOR 3' IN THE EXHAUST SYSTEM. THIS ISSUE ONLY APPLIES IF THE CODES STORED IN THE PCM ARE COVERED BY THE FOLLOWING LIST: P0142-00 O2 SENSOR CIRCUIT (BANK 1 SENSOR 3) - NO SUB TYPE INFORMATION P0162-00 O2 SENSOR CIRCUIT (BANK 2 SENSOR 3) - NO SUB TYPE INFORMATION P0042-00 HO2S HEATER CONTROL CIRCUIT (BANK 1, SENSOR 3) - NO SUB TYPE INFORMATION P0062-00 HO2S HEATER CONTROL CIRCUIT (BANK 2, SENSOR 3) - NO SUB TYPE INFORMATION P0055-00 HO2S HEATER RESISTANCE (BANK 1, SENSOR 3) - NO SUB TYPE INFORMATION P0061-00 HO2S HEATER RESISTANCE (BANK 2, SENSOR 3) - NO SUB TYPE INFORMATION CAUSE: THIS IS LIKELY CAUSED BY A PARTS QUALITY ISSUE IF: UPON DIAGNOSIS, NO FAULT IS FOUND WITH THE WIRING HARNESS OR CONNECTOR HAVING FOLLOWED THE DIAGNOSTIC INFORMATION AND HELP TEXT RELATING TO THE PCM CODES AS READ BY SDD."

THE MAIN DRIVING MANOEUVRES ASSOCIATED WITH THIS ARE: 1. STEERING RIGHT AND THEN HITTING A BUMP/RIDGE IN THE ROAD VERY SOON AFTER. 2. STEERING TO THE RIGHT AND THEN SHARPLY STEERING TO THE LEFT. CAUSE: THIS IS CAUSED BY THE FLUID MOVING WITHIN THE DYNAMIC RESPONSE VALVE BLOCK COMBINED WITH RAPID SYSTEM PRESSURE CHANGES."

THE MAIN DRIVING MANOEUVRES ASSOCIATED WITH THIS ARE: 1. STEERING RIGHT AND THEN HITTING A BUMP/RIDGE IN THE ROAD VERY SOON AFTER. 2. STEERING TO THE RIGHT AND THEN SHARPLY STEERING TO THE LEFT. CAUSE: THIS IS CAUSED BY THE FLUID MOVING WITHIN THE DYNAMIC RESPONSE VALVE BLOCK COMBINED WITH RAPID SYSTEM PRESSURE CHANGES."

TYRE PRESSURE MONITORING SYSTEM (TPMS) WARNING MESSAGES. CUSTOMERS AND RETAILERS HAVE BEEN UNABLE TO RE-INFLATE AND MAINTAIN SERVICE PRESSURES DUE TO LEAKAGE FROM THE TPMS VALVES. ISSUE MAY AFFECT: 15MY AND 16MY RANGE ROVER EVOQUE, DISCOVERY SPORT, RANGE ROVER (ALL NEW), DISCOVERY 4/LR4, RANGE ROVER SPORT VEHICLES. CAUSE: RETAILER TECHNICIANS HAVE OBSERVED TPMS VALVES WHERE THERE IS EVIDENCE OF AIR LOSS OR LEAKAGE FROM THE BASE OF THE VALVE STEM OR THROUGH THE TPMS VALVE CORE ."

CAUSE: THIS MAY BE CAUSED BY DUST AND/OR WATER INGRESS TO THE ACCESSORY DRIVE BELT IDLER PULLEY BEARING."

THE NOISE MAY BE MORE NOTICEABLE WHEN THE ENGINE IS AT IDLE SPEED AND WHEN THE ENGINE IS COLD. CAUSE: THIS MAY BE CAUSED BY A NOISY HIGH PRESSURE FUEL PUMP OUTLET VALVE."

(LW) AND DISCOVERY 4/LR4 (LA) FITTED WITH EITHER THE 3.0SC AJ126 OR 5.0NA/SC AJ133 ENGINES. CAUSE: PARTS QUALITY ISSUE (OPERATIONAL FAILURE AT SUPPLIER DURING MANUFACTURE OF THE SENSOR)."

RESTARTS IN XXX MILES, DIESEL EXHAUST FLUID DOSING MALFUNCTION WARNING MESSAGE DISPLAYED WITHIN THE INSTRUMENT CLUSTER MESSAGE CENTER AND DTCS P208B-00/P2BAE-00/P2BAF-00 STORED IN THE PCM (POWERTRAIN CONTROL MODULE) CAUSE: AIR IN THE SYSTEM."

ILLUMINATED AND NO ENGINE RESTARTS POSSIBLE IN XXX (TYPICALLY ~500) MILES. DIESEL EXHAUST FLUID DOSING SYSTEM MALFUNCTION MESSAGE ON IPK. AND ONE, OR MORE OF THE FOLLOWING DEF INDUCEMENT P-CODES ARE STORED IN THE PCM: P2BAE-00; P2BAE-02; P2BAF-00; P2BAF-02; P2BAF-04. AND P20B-00 IS STORED IN THE PCM. NOTE: IF OTHER CODES ARE STORED IN THE PCM, INVESTIGATE AND REPAIR THOSE BEFORE FOLLOWING THE ADVICE OF THIS SSM. CAUSE: THE ROOT CAUSE OF THIS ISSUE IS UNDER INVESTIGATION AND HAS YET TO BE CONFIRMED."

MODULE (PCM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE."

(ECM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

CAUSE: THIS MAY BE CAUSED DUE TO THE POTENTIAL FOR THE BLOWER MOTOR TO HIT THE UPPER LIMIT FOR CURRENT AND CUT OUT WHEN THE CLIMATE CONTROL IS ON MAXIMUM OR IF THE BLOWER MOTOR IS MANUALLY PUT TO MAXIMUM. THE ISSUE IS INTERMITTENT BECAUSE IT IS HIGHLY DEPENDENT ON THE STATE OF CHARGE OF THE BATTERY AND THE INPUTS TO THE SYSTEM. BLOWER MOTOR OPERATION CAN BE RESET BY EITHER CYCLING THE IGNITION OFF/ON OR BY CYCLING THE CLIMATE CONTROL OFF/ON MANUALLY."

MAY NOT RE-START AND THE IGNITION WILL TURN OFF. CAUSE: THIS MAY BE CAUSED BY AN ANTI-LOCK BRAKING SYSTEM (ABS) SOFTWARE, WHICH UNDER VERY SPECIFIC CIRCUMSTANCES CAN CAUSE THIS ISSUE TO OCCUR."

INVOLUNTARILY ENGAGED WHEN COMING TO A STOP OR IMMEDIATELY AFTER AN AUTOMATIC ENGINE RESTART (WHEN INTELLIGENT STOP/START IS ACTIVE)."

NOTE - AFFECTS 3.0 TD6 ONLY. CAUSE: THE TRANSIT RELAY IS FITTED PRIOR TO THE PCM PERFORMING A FULL SHUTDOWN. THIS CAN RESULT IN A FALSE FLAG OF DTC P068A-00."

BOTH TOWING EYE COVERS ARE INCORRECT SPECIFICATION CAUSE: CURRENTLY UNDER INVESTIGATION AND ENGINEERING"

CUSTOMERS OR EXTERNAL INFLUENCES SUCH AS CAR WASHES MAY INADVERTANTLY KNOCK THE DOOR MIRROR HEAD INTO THE FOLDED POSITION, THIS WILL THEN CAUSE THE MIRROR HEAD TO BE LOOSE"

ONE OR MORE CODES STORED IN THE PCM RELATING TO HEATED OXYGEN SENSOR (HO2S) IN THE EXHAUST SYSTEM. THE CODE WILL REFER TO A FAULT WITH THE PRE, OR MID, OR POST CATALYST HEATED OXYGEN SENSOR: P0030, P0031, P00D1, P0130, P0131, P0132, P0133, P0134, P0135, P014C, P2195, P2196, P2231, P2237, P2243, P2245, P2251, P2297, P2626, P2A00, P0050, P0051, P00D3, P0150, P0151, P0152, P0153, P0154, P0155, P2197, P2198, P2234, P2240, P2247, P2254, P0037, P0038, P0054, P0136, P0137, P0138, P0139, P013A, P013E, P0140, P0141, P2270, P2271, P0056, P0057, P0060, P013C, P014A, P0156, P0157, P0158, P0159, P0160, P0161, P2272, P2273, P0042, P0043, P0044, P0055, P0142, P0143, P0144, P0147, P2274, P2275, P0061, P0062, P0063, P0162, P0163, P0164, P0167, P2276, P2277 UPON DIAGNOSIS NO FAULT IS FOUND WITH THE WIRING HARNESS OR CONNECTOR AND THE FAULT IS DETERMINED TO BE WITH THE SENSOR (HAVING FOLLOWED THE DIAGNOSTIC INFORMATION AND HELP TEXT RELATING TO PCM CODES AS READ BY SDD). CAUSE: THE ROOT CAUSE HAS YET TO BE IDENTIFIED AND IS CURRENTLY UNDER INVESTIGATION."

TD6 ENGINE ONLY) VEHICLES WHERE ONE OR BOTH OF THE FOLLOWING CONDITIONS MAY BE EXPERIENCED: H AN AMBER WARNING LAMP WITH THE MESSAGE 'EXHAUST FILTER NEARLY FULL, SEE HANDBOOK'; AND/OR H A RED WARNING LAMP WITH THE MESSAGE 'EXHAUST FILTER FULL, VISIT DEALER'."

INSTRUMENT CLUSTER: FAULTY GENERATOR FAULTY BATTERY MONITORING SYSTEM (BMS) THE CHARGE WARNING INDICATOR IS ILLUMINATED WHEN THE ENGINE IS RUNNING. CAUSE: THE POWER SUPPLY IS A FULLY INTEGRATED SYSTEM THAT REQUIRES SDD TO DIAGNOSE OVERALL FUNCTIONALITY ROBUSTLY TO MAKE SURE CUSTOMER SATISFACTION IS MET VIA RIGHT FIRST TIME DIAGNOSIS."

RANGE WHERE THE PASSIVE ENTRY/PASSIVE UNLOCK AND KEYLESS START FEATURES MAY BE INOPERATIVE AND THE ENGINE WILL NOT START NORMALLY. WHEN THIS OCCURS, THE EMERGENCY KEY BLADE IS NEEDED TO UNLOCK THE DRIVERS DOOR TO ENTER THE VEHICLE AND THE SMART KEY MUST THEN BE HELD NEXT TO THE IMMOBILIZER ANTENNA UNIT (IAU) AND THE ENGINE START/STOP SWITCH MUST BE PRESSED TO START THE ENGINE.

MODULE (PCM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE.

P0132 STATUS 60 DIAGNOSTIC TROUBLE CODE (DTC) STORED IN THE POWERTRAIN CONTROL MODULE (PCM)."

(ECM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE.

PASSIVE ENTRY/PASSIVE UNLOCK AND KEYLESS START FEATURES MAY BE INOPERATIVE AND THE ENGINE WILL NOT START NORMALLY. WHEN THIS OCCURS, THE EMERGENCY KEY BLADE IS NEEDED TO UNLOCK THE DRIVERS DOOR TO ENTER THE VEHICLE AND THE SMART KEY MUST THEN BE HELD NEXT TO THE IMMOBILIZER ANTENNA UNIT (IAU) AND THE ENGINE START/STOP SWITCH MUST BE PRESSED TO START THE ENGINE."

CAUSE: THIS MAY BE CAUSED BY CUSTOMER ERROR/MISTAKE."

L405 OR LW - RANGE ROVER SPORT - L494 FOR 16 MY ONWARDS: THE RETAILER IS UNABLE TO COMPLETE THE PRE-DELIVERY INSPECTION (PDI) ON EITHER OF THE VEHICLES DETAILED ABOVE. DURING THE PDI ROUTINE, THE TECHNICIAN WILL BE UNABLE TO REMOVE THE SPEED LIMITER ON A VEHICLE WITH A 4.4 TDV8 ENGINE. WHEN THE PDI ROUTINE HAS BEEN COMPLETED, THE TECHNICIAN WILL THEN FIND THE TELEMATICS CONTROL UNIT (TCU) HAS NOT BEEN ACTIVATED DURING THE PDI ROUTINE. WHEN THEY THEN ATTEMPT TO ACTIVATE THE TCU USING SDD SERVICE FUNCTIONS THEY ARE PRESENTED WITH A LARGE AMOUNT OF VEHICLE QUALIFIER QUESTIONS. CAUSE: THREE CONCERNS HAVE BEEN IDENTIFIED: 1. THE SECURITY CONSTANTS ON SYMPTOM DRIVEN DIAGNOSTICS (SDD) DO NOT MATCH THE VEHICLE AND THIS PREVENTS SDD FROM GAINING COMMUNICATIONS WITH THE ENGINE CONTROL MODULE (ECM) KNOWN AS PCM IN SDD 2. A LATE CHANGE TO THE CAR CONFIGURATION FILE (CCF) RULES WHICH HAS BEEN LOADED TO THE VEHICLES WHEN THEY WERE MANUFACTURED. THIS CAUSES SDD NOT READ THE CCF WHICH THE SOFTWARE USES TO IDENTIFY WHAT"

THE NOISE IS MOST PROMINENT DURING LIGHT THROTTLE AND LOW SPEED, FOR EXAMPLE DURING CAR PARK MANEUVERS AND IS INDEPENDENT OF AMBIENT TEMPERATURE RANGE. UNDER THESE CONDITIONS, A LOW-LEVEL NON-CONSTANT CYCLICAL-TYPE NOISE CAN BE HEARD COMING FROM THE CENTER EXHAUST SYSTEM (EXHAUST VALVE) ADJACENT TO THE FUEL TANK.

ANALYSIS OF RETURNED ENGINES HAS SHOWN THE LEFT HAND (LH) CAMSHAFT/CHAIN SPROCKET ALIGNMENT MARKS WERE INCORRECT AS A RESULT OF THE TECHNICIAN NOT FOLLOWING THE TOPIX PROCEDURE FOR REFITTING THE FUEL INJECTION PUMP WHICH IS DRIVEN OFF THE REAR OF THE LEFT HAND (LH) SIDE CYLINDER HEAD EXHAUST CAMSHAFT.

GASKET ON VEHICLES EQUIPPED WITH THE 3.0 TDV6 ENGINE.

INCORRECTED DIESEL EXHAUST FLUID QUALITY DETECTED" WARNING DISPLAYED IN THE MESSAGE CENTER.

DISPLAYED ON THE INSTRUMENT CLUSTER. AFFECTS RANGE ROVER AND RANGE ROVER SPORT 16MYONWARDS. THE MESSAGE CAN APPEAR WHERE THE CUSTOMER SWITCHES THE IGNITION ON ONLY BUT DOESNT START THE ENGINE UNTIL AFTER A PERIOD OF 32 SECONDS. THE FOLLOWING DTC WILL HAVE BEEN LOGGED: - U0140-87: ANTI-LOCK BRAKE SYSTEM CONTROL MODULE (ABS) LOST COMMUNICATION WITH BODY CONTROL MODULE MISSING MESSAGE. THE MESSAGE WILL CLEAR AT THE NEXT IGNITION CYCLE.

THIS MAYBE ACCOMPANIED WITH THE COOLANT GAUGE READING HIGH AND/OR THE CHARGE WARNING INDICATOR ILLUMINATED. INVESTIGATION FINDS A CONCERN WITH THE PRIMARY IDLER PULLEY ASSEMBLY WHICH IN SOME CASES CAN LEAD TO DAMAGE OF THE PRIMARY DRIVE BELT. THE PRIMARY BELT DRIVES THE COOLANT PUMP AND GENERATOR HENCE THE POTENTIAL FOR THE COOLANT GAUGE TO READ HIGH AND/OR THE CHARGE WARNING INDICATOR ILLUMINATING IF THE BELT IS DAMAGED AND NOT FUNCTIONING CORRECTLY. THIS CONCERNS AFFECTS LTIS (LOW TIME IN SERVICE) VEHICLES WITH THE 3.0 AJ126 AND 5.0 AJ133 GASOLINE ENGINES FITTED.

THE ISSUE IS MORE LIKELY WHEN HIGH ELECTRICAL DEMAND SYSTEMS SUCH AS HEATED WINDSHIELD, HEATED SEATS, LIGHTS, ETC. ARE BEING USED. A CHANGE OF STATE FROM THE WIPER MOTOR IS ALSO REQUIRED (START, COMING TO REST, OR SWITCHING BETWEEN SPEED SETTINGS).

THE ISSUE IS MORE LIKELY WHEN HIGH ELECTRICAL DEMAND SYSTEMS SUCH AS HEATED WINDSHIELD, HEATED SEATS, LIGHTS, ETC. ARE BEING USED. A CHANGE OF STATE FROM THE WIPER MOTOR IS ALSO REQUIRED (START, COMING TO REST, OR SWITCHING BETWEEN SPEED SETTINGS).

UPON DIAGNOSIS, INCLUDING REMOVAL OF THE AIR SPRING AND INVERTING IT FOR A PERIOD OF APPROXIMATELY ONE MINUTE, HYDRAULIC FLUID IS FOUND TO FLOW FROM THE AIR SUSPENSION PIPE 'VOSS' CONNECTOR.

THE NOISE IS MOST PROMINENT DURING LIGHT THROTTLE AND LOW SPEED, FOR EXAMPLE DURING CAR PARK MANEUVERS AND IS INDEPENDENT OF AMBIENT TEMPERATURE RANGE. UNDER THESE CONDITIONS, A LOW-LEVEL NON-CONSTANT CYCLICAL-TYPE NOISE CAN BE HEARD COMING FROM THE CENTER EXHAUST SYSTEM (EXHAUST VALVE) ADJACENT TO THE FUEL TANK.

ON HIGH PRESSURE FUEL PUMP DIAGNOSTICS. *PE

NOT MOVED, OR GEAR POSITION INDICATOR ON INSTRUMENT CLUSTER MESSAGE IS FLASHING D OR S AND WOULD HAVE NORMAL OPERATION ONCE ENGINE IS STOPPED AND RESTARTED. *PE UPDATED 9/25/15. *PE

is in its rearmost setting.

Locking Rear Differentials - Noisy

will jump and accelerate

drive cycle.

including roller blind type load space cover housing and PVC blind material.

drive cycle.

including roller blind type load space cover housing and PVC blind material.

drive cycle.

system using the relevant USB cable only, the device is not connecting to the vehicle.

scraping or drone noise on vehicles produced within the following vin ranges ? LG Range Rover - LG000001 to LG351464, LW Range Rover Sport ? LW100000 to LW152017, LW Range Rover Sport - LW300000 to LW399999, LW Range Rover Sport - LW500000 to LW599999, LW Range Rover Sport - LW600000 to LW687306, LR Discovery ? LR000001 to LR017639

DISC'S WHICH ARE FITTED INTO THE BASE OF THE CUPHOLDERS HAVE BECOME DETACHED.

ON SELECTION OF THE BUTTON THE SEAT MAY STOP IN THE MID POSITION. ANY SUBSEQUENT BUTTON PRESSES WILL NOT OPERATE THE SEAT.

ON THE BUTTON THE SEAT MAY STOP IN THE MID POSITION. ANY SUBSEQUENT BUTTON PRESSES WILL NOT OPERATE THE SEAT.

CAUSE: THIS MAY BE CAUSED BY VARIOUS ISSUES."

RANGE ROVER (L405) VEHICLES WHICH HAVE BEEN MANUFACTURED WITHOUT THE AUTOMATIC HIGH BEAM ASSIST BEING AVAILABLE."

AFFECTS THE FOLLOWING VEHICLES ONLY: RANGE ROVER SPORT 16MY FITTED WITH THIN FILM TRANSISTOR (TFT) INSTRUMENT CLUSTER WITHOUT LANE DEPARTURE WARNING AND TRAFFIC SIGN RECOGNITION OPTIONS FITTED. RANGE ROVER 16MY FITTED WITH TFT INSTRUMENT CLUSTER WITHOUT LANE DEPARTURE WARNING AND TRAFFIC SIGN RECOGNITION OPTIONS FITTED."

THE SEAT IS IN ITS REARMOST SETTING.

SCRAPING OR DRONE NOISE.

center and DTC U2000-4B logged within the Rear Differential Control Module (RDCM).

The error message The following error was encountered: is displayed to the user.

(PCM) which may be accompanied with DTCs P2463-00 and P246B-00.

stored in the PCM

leading to unnecessary replacement of the air suspension compressor. Please note that the DTCs do not generate an air suspension fault on the instrument cluster or display any vehicle symptoms.

leading to unnecessary replacement of the air suspension compressor. Please note that the DTCs do not generate an air suspension fault on the instrument cluster or display any vehicle symptoms.

Master Controller (IMC) may show that the module is still not up to date.

Initial diagnosis shows no fault found or no measurable quiescent drain.

no longer work

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341-00 and P054A-00 will be stored within the Powertrain Control Module (PCM).

Master Controller (IMC) may show that the module is still not up to date.

Initial diagnosis shows no fault found or no measurable quiescent drain.

no longer work

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341-00 and P054A-00 will be stored within the Powertrain Control Module (PCM).

Examples of these may include: Exterior lighting, Interior lighting, Sun roof blinds, Steering Wheel Adjust, Eco stop start etc... One or more of these symptoms may be accompanied by DTC U1000-00 (Solid State Driver Protection Active - Driver Disabled) present in the BCM. If DTC U1000-00 is not present in the BCM do not continue with this SSM. Continue to diagnose and repair the inoperative BCM output as necessary using Topix as a guide.

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341- 00, P054A-00, P0303-00 and P0302-00 will be stored within the Powertrain Control Module (PCM).

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341- 00, P054A-00, P0303-00 and P0302-00 will be stored within the Powertrain Control Module (PCM).

stored in the Telematics Control Module (TCU). All or a combination of the following DTC?s may be present in the TCU: B1A56-11 - Antenna - Circuit short to ground (GSM antenna circuit short circuit to ground) B1A56-15 - Antenna - Circuit short to battery or open (GSM antenna circuit short circuit to power, open circuit, high resistance) B119F-01 - GPS Antenna - General electrical failure (Global positioning system antenna circuit short circuit to ground, short circuit to power) B119F-13 - GPS Antenna - Circuit open (Global positioning system antenna circuit open circuit, high resistance) SOS Limited Functionality may affect the TCU's ability to support the ECall function when required by the customer.

diagnostic trouble code (DTC) U3000-05 logged in the Chassis Control Module (CHCM) Vehicle suspension is in tight tolerance mode

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

module using Pathfinder or Symptom Driven Diagnostics (SDD) the module appears to be unresponsive to any further diagnostic commands or smart key remote operation.

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

module using Pathfinder or Symptom Driven Diagnostics (SDD) the module appears to be unresponsive to any further diagnostic commands or smart key remote operation.

message centre, when the vehicle ignition is switched on after the vehicle has been parked overnight. In addition a clicking noise may be heard from the Rear Junction Box when the ignition is switched on.

(HLDF) on occasions may fail to download software correctly resulting in no communications with the module and blank screen.

Upon further diagnosis, the Technician may find Diagnostic Trouble Code (DTC) C1A13-64 stored in the Chassis Control Module (CHCM).

The concern prevents the technician from using Pathfinder to diagnose or rectify concerns with the ATCM

section 418-02 - Description and Operation ? Diagnosis and Testing) for the updated wiring repair standard and guidelines.

Retailers are testing the primary battery using the Midtronics EXP-1080 tester which is reporting the battery is serviceable. The vehicle then returns with the same Customer concern of ECO Stop/Start inoperative. If a Midtronics GRX-3080 is used, the primary battery fails the test. Replacement of the primary battery resolves the concern.

This will result in the Telematics Service Provider contacting the customer to confirm if theft has occurred. Until the customer confirms that no theft has occurred, they will be blocked from using various InControl features.

center and DTC U2000-4B logged within the Rear Differential Control Module (RDCM).

center and DTC U2000-4B logged within the Rear Differential Control Module (RDCM).

center and DTC U2000-4B logged within the Rear Differential Control Module (RDCM).

center and DTC U2000-4B logged within the Rear Differential Control Module (RDCM).

recorded in the Side Object Detection Left (SODL) or Side Object Detection Right(SODR) without any customer impact on the Blind Spot Monitor features.

(DTC) B12BD-31 "Rear Camera - No Signal" and or U1A4B-49 "Control Module Processor B - Internal Failure" stored in the Image Processing Module B (IPMB). The DTC is a false flagging code that can lead to incorrect diagnosis of any camera related issue reported by the customer.

Heating Ventilation Air Conditioning (HVAC) vents when the temperatures selected on the front integrated control panel are set to the same value. During diagnosis using Pathfinder it may be evident that there are no Diagnostic Trouble Codes (DTCs) stored in the (HVAC) module.

Vehicle Range have been manufactured away from process and the Telematics Control Module (TCU) security key was not subject to an end of line test and verification. The Wi-Fi may drop out after 10 minutes and then reconnect after 3 minutes, with this cycle repeating.

For example Transportation Mode Enable. Or Deployable Side Steps Add/Remove function fails after SSM73100 (PATHFINDER fails to add Deployable Side Steps or displays an error when updating module software) has been referred to.

manufactured away from process and the Telematics Control Module (TCU) security key was not subject to an end of line test and verification. The Wi-Fi may drop out after 10 minutes and then reconnect after 3 minutes, with this cycle repeating.

Vehicle Range may have been manufactured away from process and in some cases a warning message will be displayed on the instrument cluster indicating a concern with the Diesel Exhaust Fluid (DEF) system with Diagnostic Trouble Code (DTC) P2BA9 stored in the Powertrain Control Module (PCM). If no action is taken within the specified distance, the vehicle may not start and qualified assistance may need to be sought as appropriate.

Vehicle where the Gateway Module (GWM) stays awake and keeps the Controller Area Network (CAN) awake. This constant current drain of 3 amps causes the battery to go flat within a few days.

the Gateway Module (GWM) stays awake and keeps the Controller Area Network (CAN) awake. This constant current drain of three (3) amps causes the battery to go flat within a few days.

have been manufactured away from process and in some cases a warning message will be displayed on the instrument cluster indicating a concern with the Diesel Exhaust Fluid (DEF) system with Diagnostic Trouble Code (DTC) P2BA9 stored in the Powertrain Control Module (PCM). If no action is taken within the specified distance, the vehicle may not start and qualified assistance may need to be sought as appropriate.

The failure will appear on the Jaguar Land Rover approved diagnostic tool during the ?Activate Telematics Control Module? .

Following diagnosis using Pathfinder the diagnostic trouble Code (DTC) U3000-04 ?Control module System Internal Failure? is stored in the Chassis Control Module (CHCM)

Following diagnosis using Pathfinder the diagnostic trouble Code (DTC) U3000-04 ?Control module System Internal Failure? is stored in the Chassis Control Module (CHCM).

Display Front (HLDF) may be wrongly replaced when troubleshooting, if issues are incorrectly attributed to it.

(DTC) B12BD-31 ?Rear Camera - No Signal? and or U1A4B-49 ?Control Module Processor B ? Internal Failure? stored in the Image Processing Module B (IPMB). The DTC is a false flagging code that can lead to incorrect diagnosis of any camera related issue reported by the customer.

Vehicle Range have been manufactured away from process and the Telematics Control Module (TCU) security key was not subject to an end of line test and verification. The Wi-Fi may drop out after 10 minutes and then reconnect after 3 minutes, with this cycle repeating.

For example Transportation Mode Enable. Or Deployable Side Steps Add/Remove function fails after SSM73100 (PATHFINDER fails to add Deployable Side Steps or displays an error when updating module software) has been referred to.

manufactured away from process and the Telematics Control Module (TCU) security key was not subject to an end of line test and verification. The Wi-Fi may drop out after 10 minutes and then reconnect after 3 minutes, with this cycle repeating.

Vehicle Range may have been manufactured away from process and, in some cases, the air suspension system amber warning light may appear on the instrument cluster with one or more of the Diagnostic Trouble Codes (DTC) stored in the Chassis Control Module (CHCM): C1A3112, C1A3212, C1A3312, C1A3412, C1A3512, C1A3612, C1A3712, and/or C1A3812. If the air suspension amber warning light illuminates, the vehicle may remain at its current height setting. If the DTC occurs at the 'off-road' height setting, a red warning light will illuminate if the speed exceeds 25mph / 40km/h.

have been manufactured away from process and, in some cases, the air suspension system amber warning light may appear on the instrument cluster with one or more of the Diagnostic Trouble Codes (DTC) stored in the Chassis Control Module (CHCM): C1A3112, C1A3212, C1A3312, C1A3412, C1A3512, C1A3612, C1A3712, and/or C1A3812.

Affected Vehicle where the Gateway Module (GWM) stays awake and keeps the Controller Area Network (CAN) awake. This constant current drain of 3 amps causes the battery to go flat within a few days.

the Gateway Module (GWM) stays awake and keeps the Controller Area Network (CAN) awake. This constant current drain of three (3) amps causes the battery to go flat within a few days.

may have been manufactured away from process and in some cases the Personal Subscriber Identity Module (PSIM) card Integrated Circuit Card Identifier (ICCID) number has not been recorded in line with the correct process. As a result, the customer may experience concerns with the Wi-Fi not connecting, real time traffic updates with other navigation features not working, and no activation e-mail from AT&T confirming the free trial period has started.

Heating Ventilation Air Conditioning (HVAC) vents when the temperatures selected on the front integrated control panel are set to the same value. During diagnosis using Pathfinder it may be evident that there are no Diagnostic Trouble Codes (DTCs) stored in the (HVAC) module.

VEHICLE RANGE WHICH MAY HAVE BEEN MANUFACTURED AWAY FROM PROCESS AND IN SOME CASES THE PERSONAL SUBSCRIBER IDENTITY MODULE (PSIM) CARD INTEGRATED CIRCUIT CARD IDENTIFIER (ICCID) NUMBER HAS NOT BEEN RECORDED IN LINE WITH THE CORRECT PROCESS. AS A RESULT, THE CUSTOMER MAY EXPERIENCE CONCERNS WITH THE WI-FI NOT CONNECTING, REAL TIME TRAFFIC UPDATES WITH OTHER NAVIGATION FEATURES NOT WORKING, AND NO ACTIVATION E-MAIL FROM AT&T CONFIRMING THE FREE TRIAL PERIOD HAS STARTED."

EITHER OF THE TWO ISSUES BELOW CAN OCCUR: THE DIAGNOSTIC TROUBLE CODES (DTCS) U2300-62 OR U2300-54 IS STORED IN THE BODY CONTROL MODULE (BCM). THE CCF LOADED INTO THE BCM CONTAINS FOUR CRITICAL MISMATCHES RELATED TO THE CCF ASSEMBLIES FOR DIFFERENT MODULES.

MAY HAVE BEEN MANUFACTURED AWAY FROM PROCESS AND IN SOME CASES THE PERSONAL SUBSCRIBER IDENTITY MODULE (PSIM) CARD INTEGRATED CIRCUIT CARD IDENTIFIER (ICCID) NUMBER HAS NOT BEEN RECORDED IN LINE WITH THE CORRECT PROCESS. AS A RESULT, THE CUSTOMER MAY EXPERIENCE CONCERNS WITH THE WI-FI NOT CONNECTING, REAL TIME TRAFFIC UPDATES WITH OTHER NAVIGATION FEATURES NOT WORKING, AND NO ACTIVATION E-MAIL FROM AT&T CONFIRMING THE FREE TRIAL PERIOD HAS STARTED."

START UNAVAILABLE.

START UNAVAILABLE.

WHERE EARLY LIFE FAILURES HAVE BEEN DETECTED ON THE POST CATALYST HEATED OXYGEN SENSORS DUE TO CRACKS IN THE SENSING ELEMENT OF THE POST CATALYST HEATED OXYGEN SENSOR (HO2S) ASSEMBLY. THIS RESULTS IN A LOSS OF ELECTRICAL SIGNAL FROM THE POST CATALYST HEATED OXYGEN SENSOR TO THE EXHAUST SYSTEM. THIS NOTICE DOES NOT APPLY TO VEHICLES ALREADY REGISTERED AND IN USE, EITHER WITH THE RETAILER OR THE CUSTOMER. ANY VEHICLE ALREADY IN USE MAY CONTINUE TO BE DRIVEN AND ANY REPAIR INSTRUCTIONS DEEMED NECESSARY WILL BE COMMUNICATED THROUGH A SEPARATE TECHNICAL BULLETIN OR FIELD ACTION."

MESSAGE CENTRE, WHEN THE VEHICLE IGNITION IS SWITCHED ON AFTER THE VEHICLE HAS BEEN PARKED OVERNIGHT. IN ADDITION A CLICKING NOISE MAY BE HEARD FROM THE REAR JUNCTION BOX WHEN THE IGNITION IS SWITCHED ON. CAUSE: SOFTWARE CALCULATION."

THE FOLLOWING DTCS MAY ALSO BE LOGGED: EPAS DTCS LOGGED: -B1304-16: ELECTRONIC POWER ASSISTED STEERING (EPAS) SYSTEM CIRCUIT VOLTAGE BELOW THRESHOLD -U3001-00: POWER STEERING CONTROL MODULE (PSCM) SYSTEM IMPROPER SHUTDOWN. THESE MAY BE ACCOMPANIED BY: -U0001-87 / 88 HIGH SPEED CAN BUS INVALID SERIAL DATA RECEIVED / MISSING MESSAGE. CHCM DTCS LOGGED: -U0131-00 CHASSIS CONTROL MODULE (CHCM) LOST COMMS WITH PSCM. -U3003-62 BATTERY VOLTAGE SIGNAL COMPARE FAILURE. -U0420-68 CHCM INVALID DATA RECEIVED FROM PSCM. CAUSE: THIS MAY BE CAUSED BY: -LOW BATTERY VOLTAGE. -WIRING HARNESS ISSUE (SHORT / OPEN CIRCUIT, HIGH RESISTANCE). -HIGH RESISTANCE AT EPAS EARTH TERMINAL (FOR L405/L494) G1D132 AND OR G4D178, (SEE ATTACHED DIAGRAM). OR IF ON L550/L538 HIGH RESISTANCE AT G1D122A, G1D122B, G1D122AZ AND G1D108. -POOR CONNECTION OR PIN SET CONDITION AT CONNECTOR NUMBER: C11-G1"

ONE OR MORE OF THE FOLLOWING SYMPTOMS MAY ALSO BE EVIDENT: NO AUDIO SOUND SPEAKER INTERFERENCE TOUCH SCREEN INOPERATIVE OR 'FREEZING' CAUSE: THIS MAY BE CAUSED BY THE CLIMATE CONTROL SYSTEM DRAIN TUBE BEING INCORRECTLY LOCATED IN FOOTWELL CAUSING WATER CONTAMINATION TO THE CARPETS AND POSSIBLE WATER INGRESS INTO THE AUDIO AMPLIFIER MODULE."

FROM 14MY ONWARDS L550 LAND ROVER SPORT: FROM 15MY ONWARDS WHEN FITTING A NEW REMOTE FUNCTION ACTUATOR (RFA) (REFERRED TO AS THE KEYLESS VEHICLE MODULE - KVM ON SDD) WITH A MODULE PART NUMBER OF: FK72-19H440 - AE FK72-19H440 - BE FK72-19H440 - AF FK72-19H440 - BF SDD CANNOT COMMUNICATE WITH THE RFA. THIS WILL BE DISPLAYED AS A RED X FOR THE RFA IN THE SDD VEHICLE SPECIFICATION SCREEN. CAUSE: THE NEW RFA MODULE SUPPLIED IS MANUFACTURED WITH PRE-FLASHED SOFTWARE FOR DUAL CAN VEHICLES. THESE VEHICLES ARE MULTICAN AND NOT DUAL CAN AND WILL NOT COMMUNICATE WITH SDD FOR PROGRAMMING OR UPDATE WITHOUT COMPLETING THE ACTION INSTRUCTIONS DETAILED BELOW."

THE FOLLOWING DTCS MAY ALSO BE LOGGED: EPAS DTCS LOGGED: -B1304-16: ELECTRONIC POWER ASSISTED STEERING (EPAS) SYSTEM CIRCUIT VOLTAGE BELOW THRESHOLD -U3001-00: POWER STEERING CONTROL MODULE (PSCM) SYSTEM IMPROPER SHUTDOWN. THESE MAY BE ACCOMPANIED BY: -U0001-87 / 88 HIGH SPEED CAN BUS INVALID SERIAL DATA RECEIVED / MISSING MESSAGE. CHCM DTCS LOGGED: -U0131-00 CHASSIS CONTROL MODULE (CHCM) LOST COMMS WITH PSCM. -U3003-62 BATTERY VOLTAGE SIGNAL COMPARE FAILURE. -U0420-68 CHCM INVALID DATA RECEIVED FROM PSCM. CAUSE: THIS MAY BE CAUSED BY: -LOW BATTERY VOLTAGE. -WIRING HARNESS ISSUE (SHORT / OPEN CIRCUIT, HIGH RESISTANCE). -HIGH RESISTANCE AT EPAS EARTH TERMINAL (FOR L405/L494) G1D132 AND OR G4D178, (SEE ATTACHED DIAGRAM). OR IF ON L550/L538 HIGH RESISTANCE AT G1D122A, G1D122B, G1D122AZ AND G1D108."

(IC) FOR LESS THAN ONE SECOND WHEN NO SERVICE IS REQUIRED. CAUSE: THIS MAY BE CAUSED BY A DISCREPANCY BETWEEN THE VALUES IN THE POWERTRAIN CONTROL MODULE (PCM) AND THE IC FOR NEXT SERVICE INITIALIZATION."

INSTRUMENT CLUSTER FOR <1 SECOND (WHEN NO SERVICE IS REQUIRED). NO CUSTOMER SYMPTOMS UNTIL A SERVICE RESET HAS BEEN PERFORMED. WHEN AN ACTUAL SERVICE IS REQUIRED THE MESSAGE WILL APPEAR FOR 4 SECONDS AS DESIGN INTENT. CAUSE: DISTANCE TO NEXT SERVICE INITIALISATION VALUE MANAGEMENT BETWEEN ECM AND INSTRUMENT CLUSTER (FIRST 900MS)."

DISPLAY, AT THE NEXT IGNITION CYCLE THE SCREENSAVER HAS RETURNED TO A BLANK SCREEN (THE SCREENSAVER WILL NOT SAVE). THIS IS LIKELY TO OCCUR IN VEHICLES WITH EITHER A LOW-LEVEL OR MID-LEVEL INFOTAINMENT SYSTEM THAT IS NOT BRANDED AS MERIDIAN ON 2016 MODEL YEAR VEHICLES ONWARDS.

MODULE PART NUMBER OF: FK72-19H440 - AE; FK72-19H440 - BE; FK72-19H440 - AF; FK72-19H440 - BF SDD CANNOT COMMUNICATE WITH THE RFA. THIS WILL BE DISPLAYED AS A RED X FOR THE RFA IN THE SDD VEHICLE SPECIFICATION SCREEN."

AREA OF THE TAILGATE HARNESS RUBBER SLEEVE.

MODULE (PSCM): '0000-00 [NO INFORMATION AVAILABLE] THERE IS NO CUSTOMER REPORTABLE SYMPTOM RELATED TO THIS DTC. CAUSE: THIS DTC HAS BEEN INCORRECTLY SET TO BE VISIBLE IN PRODUCTION SOFTWARE."

ASSOCIATED COMPONENTS REPLACED FOR A NON-START CONDITION. FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORISED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

DISPLAY, AT THE NEXT IGNITION CYCLE THE SCREENSAVER HAS RETURNED TO A BLANK SCREEN (THE SCREENSAVER WILL NOT SAVE). THIS IS LIKELY TO OCCUR IN VEHICLES WITH EITHER A LOW-LEVEL OR MID-LEVEL INFOTAINMENT SYSTEM THAT IS NOT BRANDED AS MERIDIAN ON 2016 MODEL YEAR VEHICLES ONWARDS

Waze.

to respond or no functionality at all.

versions.

Examples of this may include: No infotainment audio, No audio from Park Aid, No audio from Rear Seat Entertainment, Customers with Telematics fitted may also report that internet connectivity is inoperative.

Examples of this may include: No infotainment audio, No audio from Park Aid, No audio from Rear Seat Entertainment, Customers with Telematics fitted may also report that internet connectivity is inoperative.

is not available? displayed on the instrument Cluster? due to activation failure.

from Phase 2.5 to the latest level for vehicles equipped with Rear Seat Entertainment. This concern can leave the ISC in a non-communicative state.

Bluetooth the user may experience a connectivity issues.

inoperative

.The concern occurs when updating to phase 4.0 using PATHFINDER 180

Bluetooth the user may experience a connectivity issues.

can no longer provide Navigation destination entry via voice control.

inoperative

.The concern occurs when updating to phase 4.0 using PATHFINDER 180

from Phase 2.5 to the latest level for vehicles equipped with Rear Seat Entertainment. This concern can leave the ISC in a non-communicative state.

Bluetooth the user may experience a connectivity issues.

Bluetooth the user may experience a connectivity issues.

can no longer provide Navigation destination entry via voice control.

from Phase 2.5 to the latest level for vehicles equipped with Rear Seat Entertainment. This concern can leave the ISC in a non-communicative state.

Bluetooth the user may experience a connectivity issues.

left or right tune soft key buttons or when selecting an alternative radio band (ie trying to change from FM to DAB) there is no response from touch screen and audio output remains distorted. The DTC B14D3-96 may also be stored in the Infotainment Master Controller (IMC) suggesting a radio tuner component internal failure.

The Audio/Video button on touch-screen home page may also be greyed out.

the InControl Touch Pro system, or cause system functionality concerns after the infotainment system was successfully updated.

the InControl Touch Pro system, or cause system functionality concerns after the infotainment system was successfully updated.

the InControl Touch Pro system, or cause system functionality concerns after the infotainment system was successfully updated.

longer process voice inputs or outputs. Common symptoms are reported as: Voice commands are not recognized. Voice output such as spoken navigation guidance is inoperative.

Range where depending on the type and style of driving that the vehicle is subjected to, the 'Service Required' message may be displayed on the Instrument Cluster (IC) at a distance less than that shown in the service interval plans. The software update within the Technical Bulletin listed below will separate the oil dilution counter from the time and distance service counter, allowing individual counter resets to be applied depending on the type of service completed.

and style of driving that the vehicle is subjected to, the 'Service Required' message may be displayed on the Instrument Cluster (IC) at a distance less than that shown in the service interval plans. The software update within the Diagnostic Procedures will separate the oil dilution counter from the time and distance service counter, allowing individual counter resets to be applied depending on the type of service completed.

to respond or no functionality at all.

designed.

DTC Flagged P0404-77/84.

Upon further inspection, the coolant level in the coolant expansion tank is at the correct level (between the MIN and MAX indicator marks).

which may have been manufactured away from process and, in some cases, the audio system does not perform to its design intent. Investigations have identified that the radio will be unable to tune to certain AM/FM stations and the third-party caller on the hands-free system will not be able to hear the driver/passenger clearly. In addition, the Satellite Navigation road colors and favorites will not be displayed correctly, with Volvo retailers appearing instead of Land Rover retailers.

DTC'S MAY BE FLAGGED P0404-77/84, P042E-72 OR P042F-73.

TIME TO SERVICE IS BELOW THE 16,000 MILES (26,000 KM) OR 12 MONTH SERVICE INTERVAL.

IN ADDITION THE CURRENT VEHICLE LOCATION INDICATOR WILL NOT LOCK ONTO THE CORRECT LOCATION ON THE MAP. CAUSE: SOFTWARE ERROR."

WHEN THE TERRAIN RESPONSE CONTROL IS SET TO AUTO MODE. ON OCCASIONS THE WHEEL POSITION SHOWN IN THE MESSAGE CENTRE APPEARS TO REMAIN IN A CONSTANT POSITION THAT DOES NOT MATCH THE ROAD WHEEL POSITION. THE DISPLAY WILL RETURN TO NORMAL WHEN THE VEHICLE IS STATIONARY. PLEASE VIEW THE ATTACHMENT THAT SHOWS THE MESSAGE CENTRE DISPLAY. CAUSE: SOFTWARE CALCULATION. LOW LINE INSTRUMENT CLUSTER AFFECTED ONLY."

WHERE THE TOUCH SCREEN MAY GO 'BLACK' FOR 10 SECONDS FOLLOWED BY DISPLAYING THE 'LAND ROVER' LOGO BEFORE RETURNING TO NORMAL DISPLAY OPERATION."

WHERE THE TOUCH SCREEN MAY GO 'BLACK' FOR 10 SECONDS FOLLOWED BY DISPLAYING THE 'LAND ROVER' LOGO BEFORE RETURNING TO NORMAL DISPLAY OPERATION. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

IN THE INSTRUMENT CLUSTER MESSAGE CENTER WHEN THE TERRAIN RESPONSE SWITCHPACK IS SET TO AUTO MODE. THE WHEEL POSITION SHOWN IN THE MESSAGE CENTER MAY APPEAR TO REMAIN IN A CONSTANT POSITION THAT DOES NOT MATCH THE POSITION OF THE ROAD WHEEL. THE MESSAGE CENTER DISPLAY WILL RETURN TO NORMAL WHEN THE VEHICLE IS STATIONARY.

CAUSE THERE IS A POTENTIAL THAT THE TOP WINDSCREEN SEAL HAS BECOME DISLODGED OVER TIME CAUSING A WINDNOISE"

CAUSE: THIS MAY BE CAUSED BY THE THRESHOLD TEMPERATURE FOR THE RED LASER DIODE TO TURN ON BEING TOO LOW."

PER MONTH AND REQUIRES A RESET ON A REGULAR BASIS.

PLAYBACK.

Sport (L494) and Range Rover (L405) vehicles where the Touch Screen may go 'black' for 10 seconds followed by displaying the 'Land Rover' logo before returning to normal display operation.

a door is opened/ closed.

a door is opened/ closed.

Symptoms include latches that will not lock/will not unlock/will not open.

which demonstrates the issue.

Symptoms include latches that will not lock / will not unlock / will not open.

which demonstrates the issue.

Symptoms include latches that will not lock/will not unlock/will not open.

bulging.

DEFINITION OF THE PAINT FINISH (SEE ATTACHED FILE FOR AN EXAMPLE)

APPEARS REDDISH IN COLOUR WHEN COMPARED TO THE 1ST & 3RD ROW GLASS. THE ISSUE CAN ONLY BE SEEN IN CERTAIN DIRECT LIGHTING CONDITIONS. SEE ATTACHED PHOTOS FOR EXAMPLES. CAUSE: THE PIGMENT IN THE LAMINATE OF THE GLASS IS VISIBLE."

CAUSE: PART SUPPLY CONSTRAINTS."

WHICH DEMONSTRATES THE ISSUE.

CAUSE: THIS MAY BE CAUSED BY THE VEHICLE BODY NOT BEING TO THE ORIGINAL DESIGN SPECIFICATION."

CAUSE: REPLACEMENT OF THE A-PILLAR EXTERIOR TRIM."

CAUSE: THIS MAY BE CAUSED BY A BUILD-UP OF DIRT AND GREASE ON THE SURFACE OF THE WINDSHIELD GLASS."

EACH OTHER IN THE VEHICLE AND REQUIRES THE EXTERIOR DOOR HANDLE LOCK BUTTON TO BE PRESSED. ISSUE IT HAS BEEN HIGHLIGHTED THAT IT IS POSSIBLE TO LOCK THE VEHICLE WITH BOTH KEYS INSIDE. KEYS ARE HELD TOGETHER BY CABLE TIES WHEN DELIVERED TO THE RETAILER."

REPLACED DUE TO REPORTED FLUID LEAKS. UPON FURTHER INSPECTION NO FAULTS ARE FOUND WITH THE RETURNED ROLL BARS. CAUSE: IT IS BELIEVED THAT MANY OF THE LEAKS REPORTED COULD BE COMING FROM THE PIPING, SEALS, INTERFACE OR TIGHTNESS OF BLEED SCREW."

CAUSE. THIS MAY BE CAUSED BY NOT POSITIONING THE ELECTRONIC TOLL TAG PROPERLY IN THE INFRARED RADIATION REFLECTIVE (IRR) LAYER CUT OUT ON THE WINDSHIELD. .

IS BELOW 3 MPH, WITH THE VEHICLE IN A CAR WASH OR IN HEAVY RAIN AND WITH THE REMOTE KEY NOT IN CLOSE PROXIMITY TO THE TAILGATE.

BULGING.

*PE

The areas around the stitching and spokes, or the lower half of the steering wheel, may appear cooler than the rest of the wheel. The heated steering wheel is otherwise operating correctly, and no DTCs are stored.

This bulletin provides diagnostic advice in advance of changes to the TOPIx workshop manual.

The noise is most prominent while accelerating/decelerating and when turning the steering wheel, such as when performing a U-turn and applying the throttle.

The noise is most prominent while accelerating/decelerating and when turning the steering wheel, such as when performing a U-turn and applying the throttle.

The 'clonk' will be most prominent while accelerating/decelerating and when turning the steering wheel. The noise may be more noticeable when performing a U-turn and applying the throttle.

situations.

steering at low vehicle speeds, such as turning left or right at an intersection.

BY VISUAL OR AUDIBLE WARNINGS THROUGH THE INSTRUMENT PACK.

STEERING AT LOW VEHICLE SPEEDS, SUCH AS TURNING LEFT OR RIGHT AT AN INTERSECTION.

CAUSE DEGRADATION OF THE PROTECTIVE COVER IN CERTAIN CLIMATIC CONDITIONS."

instrument cluster.

and/or has a poor finish.

The EPB applied light is not on. The ABS (Anti-lock braking system), DSC (Dynamic stability Control) and brake warning lights are on. The "Autonomous Emergency Braking not available" message is displayed.

heard from the front brakes during low-speed driving forward/backward, the 'squeal' can be heard also during moderate brake pedal application at low speeds, until the vehicle comes to a stop. The 'squeal' noise may resonate at frequencies of around 7kHz and 8kHZ.

housing.

and/or has a poor finish.

the following DTC stored within the Anti-Lock Braking System (ABS) module. U0001-82 High Speed CAN Communication Bus - Alive/sequence counter incorrect / not updated

and/or has a poor finish.

the following DTC stored within the Anti-Lock Braking System (ABS) module. U0001-82 High Speed CAN Communication Bus - Alive/sequence counter incorrect / not updated

heard from the front brakes during low-speed, light-to-moderate brake pedal application, until the vehicle comes to a stop.

EPQR & TA data provided by retailers to date, shows a varied range of conditions (environmental, drive cycle and road type) that may initiate the known noises. Although the noises do not, in most cases, indicate a degradation in functionality or braking performance, they may lead to customer dissatisfaction and unscheduled retailer visits for repair action. Note: Off road use of the vehicle is not categorised in the communication due to the extended range of parameters and conditions that the vehicle operate at. Defining and describing brake noises is proven to be difficult through our different languages and terminology. In the ?Solutions? section below, there are noise descriptions and Technical Service Bulletins references to aid the repair selection. See ?Action? for further guidance.

EPQR & TA data provided by retailers to date, shows a varied range of conditions (environmental, drive cycle and road type) that may initiate the known noises. Although the noises do not, in most cases, indicate a degradation in functionality or braking performance, they may lead to customer dissatisfaction and unscheduled retailer visits for repair action. Note: Off road use of the vehicle is not categorised in the communication due to the extended range of parameters and conditions that the vehicle operate at. Defining and describing brake noises is proven to be difficult through our different languages and terminology. In the ?Solutions? section below, there are noise descriptions and Technical Service Bulletins references to aid the repair selection. See ?Action? for further guidance.

and/or has a poor finish.

noise may be heard from the front brakes during low-speed, light-to-moderate brake pedal application, until the vehicle comes to a stop.

the following DTC stored within the Anti-Lock Braking System (ABS) module. U0001-82 High Speed CAN Communication Bus - Alive/sequence counter incorrect / not updated.

may be heard from the front brakes during low-speed, light-to-moderate brake pedal application, until the vehicle comes to a stop.

NOISE MAY BE HEARD FROM THE FRONT BRAKES DURING LOW-SPEED, LIGHT-TO-MODERATE BRAKE PEDAL APPLICATION, UNTIL THE VEHICLE COMES TO A STOP."

POOR FINISH.

POOR FINISH.

CAUSE BRAKE LIGHT SWITCH / BRAKE PEDAL SHIM INTERACTION. NOTE: NOT ALL VEHICLES WILL BE FITTED WITH BRAKE PEDAL SHIM."

NOISE MAY BE HEARD FROM THE FRONT BRAKES DURING LOW-SPEED, LIGHT-TO-MODERATE BRAKE PEDAL APPLICATION, UNTIL THE VEHICLE COMES TO A STOP. CAUSE: THIS MAY BE CAUSED BY FRONT BRAKE PAD RESONANCE."

CAUSE: A LACK OF GREASING DURING PAD REPLACEMENT OR BRAKE USAGE CHARACTERISTIC."

CAUSE: THIS MAY BE CAUSED BY ICE BUILD UP BETWEEN THE FOAM SURFACES AND THE HOOD CAUSING PENETRATION INTO THE FOAM."

MAY HAVE BEEN MANUFACTURED AWAY FROM PROCESS AND IN SOME CASES, A YELLOW WARNING LIGHT MAY BE ILLUMINATED ON THE INSTRUMENT CLUSTER WITH THE WARNING 'ELECTRONIC PARK BRAKE FAULT'. IN THESE CIRCUMSTANCES, THERE IS NO PERFORMANCE ISSUE ASSOCIATED WITH THE OPERATION OF THE ELECTRIC PARK BRAKE BUT THE WARNING INDICATOR WILL CAUSE CONCERN AND CUSTOMER DISSATISFACTION UNTIL THE REQUIRED REMEDIAL WORK HAS BEEN COMPLETED."

MAY BE HEARD FROM THE REAR BRAKES DURING LIGHT BRAKING.

PAGE 2 TO SFCC_APR2021_46

be damaged.

(blowing warm and then cold); ? Windshield, rear window, and/or door windows mist up in cool (15C or lower) ambient temperatures; ? Poor cooling performance of the Air Conditioning (A/C) system; and/or ? Warm, damp or musty smells coming from the vents.

system is in operation and low temperature selected.

OR REAR CLIMATE FANS ARE ON A HIGH SETTING. ALSO, AN INTERMITTENT TAPPING/ RATTLE MAYBE HEARD.

WHEN SELECTED.

CAUSE: THIS MAY BE CAUSED BY PARAMETERS WITHIN THE CLIMATE CONTROL SYSTEM NOT OPERATING EFFICIENTLY."

ROVER (LG; L405) VEHICLES WHERE THE REAR SEAT HEAT CANNOT BE ADJUSTED OR SWITCHED ON OR OFF WHEN THE REAR CLIMATE CONTROL PANEL IS SWITCHED OFF VIA THE REAR BLOWER ROTARY."

ROVER (LG; L405) VEHICLES WHERE THE REAR SEAT HEAT CANNOT BE ADJUSTED OR SWITCHED ON OR OFF WHEN THE REAR CLIMATE CONTROL PANEL IS SWITCHED OFF VIA THE REAR BLOWER ROTARY. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN"

displaying less fuel than what is actually in the fuel tank [gauge reading when the fuel tank is full]).

displaying less fuel than what is actually in the fuel tank [gauge reading when the fuel tank is full]).

DISPLAYING LESS FUEL THAN WHAT IS ACTUALLY IN THE FUEL TANK [GAUGE READING WHEN THE FUEL TANK IS FULL])."

CAUSE: 1. THE SERVICE MENU WITHIN THE INSTRUMENT CLUSTER ON A NEW VEHICLE MAY DISPLAY A DEFAULT VALUE OF APPROXIMATELY 12,000 MILES AS THE DISTANCE TO EMPTY FOR DEF."

THE EVAPORATIVE EMISSION CANISTER HOSE MAY SHOW SIGNS OF OZONE CRACKING.

The customer may experience one of the following symptoms: ? The release button appears loose or has no resistance when operated. ? The release button appears to be binding or will not move when operated.

The button on the shifter does not work.

is pressed and the selector operated with one or more of the following symptoms noted on a Range Rover Sport 2014-2016 MY only: Release button appears loose or no resistance when pressed, Release button appears to be binding or will not move when pressed.

Transmission Control Switch and/or Instrument Cluster (IC) following an ECO Stop/Start event. ONLY DTCs P0715-64 and P0700-02 are stored in the Transmission Control Module (TCM) P0715-64 - Input/Turbine Shaft Speed Sensor "A" Circuit - signal plausibility failure P0700-02 - Transmission Control System (MIL Request) - general signal failure. If there are any other DTCs stored in the TCM they must be investigated and rectified prior to carrying out the instruction detailed in this SSM. Refer to the DTC index on TOPIx ? 100-00 General Information ? Diagnostic Trouble Code Index DTC: Transmission Control Module (TCM) NOTE ? The concern detailed in this SSM is applicable to 2017 and 2018 MY vehicles and typically occurs at low mileage (below 2500 miles/4000 kilometres) and affects vehicles fitted with the 8HP45 or 8HP70 automatic transmission.

exhibit intermittent operation, causing one or more of the following issues: ? Audio volume does not adjust (up and/or down)? Radio 'seek' buttons do not operate ? Volume control buttons cause the radio station to change ? InControl system slow to operate (blank screen followed by the 'Land Rover' logo) ? Transmission paddle shifters do not operate ? Diagnostic Trouble Codes (DTC) U2013-02 and/or B1D21-13 stored

THE CALIBRATION OF THE TRANSMISSION CONTROL MODULE (TCM).

UPON INSPECTION, LOW PRESSURE IS RECORDED ON THE HIGH PRESSURE SYSTEM, HIGH PRESSURE IS RECORDED ON THE LOW PRESSURE SYSTEM, AND THE COMPRESSOR CLUTCH (WHERE APPLICABLE) IS WORKING PROPERLY.

CALIBRATION OF THE TRANSMISSION CONTROL MODULE (TCM).

CALIBRATION OF THE TRANSMISSION CONTROL MODULE (TCM).

PLEASE VIEW ATTACHMENT THAT SHOWS THE CONDITION. CAUSE: PAINT SURFACE FINISH PROCESS"

This applies to both high line and low line rear camera.

SOTA updates sent direct to customers on SOTA eligible & enabled vehicles with latest level IMC software.

Driven Diagnostics (SDD) does not appear to communicate with the RFA: FK72-19H440-AE, FK72-19H440-BE, FK72-19H440-AF, FK72-19H440-BF, Following models only affected: L538 Range Rover Evoque 14MY onwards, L550 Discovery Sport 15MY onwards, L494 Range Rover Sport 14MY onwards, L405 Range Rover 14MY onwards

This can cause the alarm to trigger or the vehicle to not lock.

When interrogated with diagnostic equipment the following fault codes may be present: C1A20-64, C1131-92

Instead, the vehicle will start to lower, and then rise to off-road / raised height with a warning light on the instrument pack. This occurs when the vehicle lowers much more slowly than expected.

Instead, the vehicle will start to lower, and then rise to off-road / raised height with a warning light on the instrument pack. This occurs when the vehicle lowers much more slowly than expected.

Instead, the vehicle will start to lower, and then rise to off-road / raised height with a warning light on the instrument pack. This occurs when the vehicle lowers much more slowly than expected.

FITTED WITH 21"" WHEELS AND A FULL-SIZE SPARE WHEEL, WHERE THE SPARE WHEEL LIFT ASSIST STRAP IS MISSING FROM THE VEHICLE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

HAVE BEEN MANUFACTURED WITHOUT THE AUTOMATIC HIGH BEAM ASSIST BEING AVAILABLE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

Fault codes U210A - 16 and C1A24 - 67 may also be stored.

On investigation the front Air Spring is found to be misaligned and damaged.

manufactured away from process and, in some cases, a general warning/information message (red or amber) for the air suspension system. This could occur in normal driving when the air suspension system attempts to vent air or when the vehicle attempts to lower itself, either by the driver demand or automatic access.

may have been manufactured away from process and, in some cases, a general warning/information message (red or amber) for the air suspension system will display. This could occur in normal driving when the air suspension system attempts to vent air or when the vehicle attempts to lower itself, either by the driver demand or automatic access.

CAUSE: THIS MAY BE CAUSED BY METAL-TO-METAL CONTACT BETWEEN THE SEAT SUSPENSION MAT HOOKS AND THE SEAT FRAME AND MAY BE VERIFIED BY VISUAL INSPECTION OF SEAT SUPPORT MAT LOCATION HOLE WEAR."

DIAGNOSTIC TROUBLE CODE (DTC) C1A13-64 MAY BE STORED.

DIAGNOSTIC TROUBLE CODE (DTC) C1A13-64 MAY BE STORED.

Please refer to the following publications on TOPIx for the latest details. Land Rover SSM #73635

Upon further inspection no faults are found with the returned roll bars.

Upon further inspection no faults are found with the returned roll bars.

Upon further inspection no faults are found with the returned roll bars.

Upon further inspection no faults are found with the returned roll bars.

be ?No Fault Found? during part return analysis.

point.

(IC) FOR LESS THAN ONE SECOND WHEN NO SERVICE IS REQUIRED.

limited number of 2016 model year Range Rover Sport (L494) and Range Rover (L405) vehicles which have been manufactured without the Automatic High Beam Assist being available.

This is only a temporary position and will be included in a future update to the publications on TOPIx.

with InControl Touch Pro to latest software version NGI 17C on both Symptom Driven Diagnostics (SDD) and PATHFINDER. Additional vehicle feedback data shows that the failure rate is increasing, despite the many improvements made in Pathfinder 123 and SDD 152.00. JLR recommend that no further vehicles are routinely updated to NGI 17C. (Note below reference urgent vehicles only.)

CONTROLLER (ISC, FOR REAR SEAT ENTERTAINMENT ) THE SYSTEM MAY EXHIBIT THE FOLLOWING CONDITIONS DUE TO INCOMPLETE VARIANT CONFIGURATION LEARN PROCEDURE DURING THE SOFTWARE UPDATE."

CAUSE: THIS MAY BE CAUSED BY A SOFTWARE ISSUE WITH THE REMOTE FUNCTION ACTUATOR (RFA)."

CAUSE: CERTAIN 16MY LAND ROVERS WILL NOW BE OPTIONALLY EQUIPPED WITH WI-FI (SEE MARKETING BULLETIN MPR15-21ANNOUNCING INCONTROL WI-FI)."

which may have second row outer seatbelt retractors where the pre-tensioner may not operate correctly when required. Investigations are currently ongoing. There are no other vehicle functional issues associated with this error. This program does not apply to any vehicle already registered and in use, either with the retailer or customer. Any vehicle already in use may continue to be driven and any repair instructions deemed necessary will be communicated through a separate Field Action or Technical Bulletin.

may have second row seating outer seatbelt retractors where the pre-tensioner may not operate correctly when required. Investigations are currently ongoing. There are no other vehicle functional issues associated with this error.

which may have second row outer seatbelt retractors where the pre-tensioner may not operate correctly when required. Investigations are currently ongoing. There are no other vehicle functional issues associated with this error. This program does not apply to any vehicle already registered and in use, either with the retailer or customer. Any vehicle already in use may continue to be driven and any repair instructions deemed necessary will be communicated through a separate Field Action or Technical Bulletin.

may have second row seating outer seatbelt retractors where the pre-tensioner may not operate correctly when required. Investigations are currently ongoing. There are no other vehicle functional issues associated with this error.

may have second row seating outer seatbelt retractors where the pre-tensioner may not operate correctly when required. Investigations are currently ongoing. There are no other vehicle functional issues associated with this error.

which may have second row outer seatbelt retractors where the pre-tensioner may not operate correctly when required. Investigations are currently ongoing. There are no other vehicle functional issues associated with this error. This program does not apply to any vehicle already registered and in use, either with the retailer or customer. Any vehicle already in use may continue to be driven and any repair instructions deemed necessary will be communicated through a separate Field Action or Technical Bulletin.

We require all retailers to follow the procedure outlined below ahead of conducting wheel alignment warranty work on Evoque (L538), Discovery Sport (L550), RR (L405), RRS (L494), Discovery (L462), and Velar (L560).

RANGE, FITTED WITH 21"" WHEELS AND A FULL-SIZE SPARE WHEEL, WHERE THE SPARE WHEEL LIFT ASSIST STRAP IS MISSING FROM THE VEHICLE."