2015 Land Rover Range Rover Sport TSBs

incorrectly changed for knock issues when the front bush is cracked and should have been replaced as per Technical Service Bulletins LTB00204v4 and LTB00123v4.

has been observed with associated Tyre Pressure Monitoring System (TKPMS) warning messages. Customers and retailers have been unable to re-

engine Malfunction Indicator Lamp (MIL) may be illuminated on the Instrument Cluster (IC) and Oxygen (O2) sensor performance-related Diagnostic Trouble Codes (DTC) may be stored in the Powertrain Control Module (PCM).

There is a hesitation. The Check Engine MIL goes on and off. There is a noise on startup.

Engine MIL illuminated with one of the following DTCs stored in the PCM. P228F-85 P025C-11 P0251-13 P064A-38 P0256-13

Any of the following DTCs (indicating an air intake system leak) could be stored in the Powertrain Control Module (PCM) ? P2187, P2189, P0505, P0507.

DTCs vary, may include P2187-00, P2189-00, P013E-00,P014E-00. Fuel trims near limit when engine is at idle speed.

flashing (see attachment) with engine off

flashing (see attachment) with engine off

Diagnostic Trouble Code (DTC) B1B87-31, stored in Driver Seat Module (DSM) or Passenger Seat Module (PSM) Note that the seat height motor is supplied as part of the cushion sub-assembly or motor sub-assembly (depending on model)

flashing (see attachment) with engine off

flashing (see attachment) with engine off

Diagnostic Trouble Code (DTC) B1B87-31, stored in Driver Seat Module (DSM) or Passenger Seat Module (PSM) Note that the seat height motor is supplied as part of the cushion sub-assembly or motor sub-assembly (depending on model)

flashing (see attachment) with engine off

flashing (see attachment) with engine off

Engineering would like to investigate the root cause as to these concerns

They may not be able to release the EPB for a short period of time following this message The following 4 DTC?s will be logged within the Anti-lock Brake System (ABS) module: C2005-71 - Right actuator ? Actuator Stuck C2006-71 - Left actuator ? Actuator Stuck C2007-72 ? Right Motor ? Actuator Stuck open C2008-72 - Left Motor ? Actuator Stuck open

Engineering would like to investigate the root cause as to these concerns

They may not be able to release the EPB for a short period of time following this message The following 4 DTC?s will be logged within the Anti-lock Brake System (ABS) module: C2005-71 - Right actuator ? Actuator Stuck C2006-71 - Left actuator ? Actuator Stuck C2007-72 ? Right Motor ? Actuator Stuck open C2008-72 - Left Motor ? Actuator Stuck open

They may not be able to release the EPB for a short period of time following this message The following 4 DTC?s will be logged within the Anti-lock Brake System (ABS) module: C2005-71 - Right actuator ? Actuator Stuck C2006-71 - Left actuator ? Actuator Stuck C2007-72 ? Right Motor ? Actuator Stuck open C2008-72 - Left Motor ? Actuator Stuck open

seam.

housing seam.

The sound may be noticeable, when one of the front wheels travels over a uneven surface while the opposite front wheel remains on a smooth surface.

They may not be able to release the EPB for a short period of time following this message The following 4 DTC?s will be logged within the Anti-lock Brake System (ABS) module: C2005-71 - Right actuator ? Actuator Stuck, C2006-71 - Left actuator ? Actuator Stuck, C2007-72 ? Right Motor ? Actuator Stuck open, C2008-72 - Left Motor ? Actuator Stuck open

message will not appear on the Instrument Cluster (IC) if a vehicle has reached its service point and the engine is started normally by pressing the engine START/STOP button with the brake pedal pressed. Turning on the ignition only, by pressing the engine START/STOP button without the brake pedal pressed, will still allow the 'Service Required' warning message to be displayed.

Trouble Code) P132B-77 stored in the Powertrain Control Module (PCM).

isolation.

housing seam.

The sound may be noticeable, when one of the front wheels travels over a uneven surface while the opposite front wheel remains on a smooth surface.

They may not be able to release the EPB for a short period of time following this message The following 4 DTC?s will be logged within the Anti-lock Brake System (ABS) module: C2005-71 - Right actuator ? Actuator Stuck, C2006-71 - Left actuator ? Actuator Stuck, C2007-72 ? Right Motor ? Actuator Stuck open, C2008-72 - Left Motor ? Actuator Stuck open

message will not appear on the Instrument Cluster (IC) if a vehicle has reached its service point and the engine is started normally by pressing the engine START/STOP button with the brake pedal pressed. Turning on the ignition only, by pressing the engine START/STOP button without the brake pedal pressed, will still allow the 'Service Required' warning message to be displayed.

Trouble Code) P132B-77 stored in the Powertrain Control Module (PCM).

isolation.

leaks incorrectly being identified as coming from the rear transmission oil seal or sump. Oil weeps through the aluminium of the casing in the base of the pocket around where the steel D clutch tube is embedded, refer to attached file.

Code (DTC) P132B-77 stored in the Powertrain Control Module (PCM).

message will not appear on the Instrument Cluster (IC) if a vehicle has reached its service point and the engine is started normally by pressing the engine START/STOP button with the brake pedal pressed. Turning on the ignition only, by pressing the engine START/STOP button without the brake pedal pressed, will still allow the 'Service Required' warning message to be displayed. In addition, the latest Powertrain Control Module (PCM) software has introduced a concern relating to the ability to reset the service message indicator. The latest IC software will rectify these concerns.

The sound may be noticeable, when one of the front wheels travels over a uneven surface while the opposite front wheel remains on a smooth surface.

message will not appear on the Instrument Cluster (IC) if a vehicle has reached its service point and the engine is started normally by pressing the engine START/STOP button with the brake pedal pressed. Turning on the ignition only, by pressing the engine START/STOP button without the brake pedal pressed, will still allow the 'Service Required' warning message to be displayed. In addition, Powertrain Control Module (PCM) software introduced a concern relating to the ability to reset the service message indicator. The latest IC software will rectify these concerns.

message will not appear on the Instrument Cluster (IC) if a vehicle has reached its service point and the engine is started normally by pressing the engine START/STOP button with the brake pedal pressed. Turning on the ignition only, by pressing the engine START/STOP button without the brake pedal pressed, will still allow the 'Service Required' warning message to be displayed. In addition, the latest Powertrain Control Module (PCM) software has introduced a concern relating to the ability to reset the service message indicator. The latest IC software will rectify these concerns.

This concern can be described as Shock/Clunk, Tip In Clonk. The concern is specific to vehicles fitted with Euro 5 AJ126 Supercharged engine only.

As the driving mode changes, the transmission may downshift, the engine Revolutions Per Minute (RPM) may also increase, and/or the 'Auto Stop/Start OFF' warning indicator may illuminate on the Instrument Cluster (IC).

Range which will not display the 'Service Required' message on the Instrument Cluster, when starting the engine by depressing the brake pedal and pressing the engine START/STOP button, if/when a vehicle has reached its service interval. The message will display when switching the ignition only 'ON' (engine OFF) by pressing the engine START/STOP button and NOT depressing the brake pedal.

may not re-start and the ignition will turn off.

MANY ARE DEEMED AS NO FAULT FOUND. IT IS POSSIBLE DURING AN ECO STOP START THAT THE VEHICLE DOES NOT RE-START. CAUSE INCORRECT DIAGNOSIS."

LEAKS INCORRECTLY BEING IDENTIFIED AS COMING FROM THE REAR TRANSMISSION OIL SEAL OR SUMP.

TO AN EVAPORATIVE EMISSION (EVAP) FAULT STORED IN THE POWERTRAIN CONTROL MODULE (PCM).

DISPLAYED IN THE INSTRUMENT CLUSTER; ENGINE FAILS TO CRANK; VEHICLE MAY NOT UNLOCK / LOCK WHEN USING PASSIVE ENTRY OR WHEN PRESSING A SMART KEY BUTTON.

(ECM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE.

UPON DIAGNOSIS, THE TECHNICIAN MAY FIND ONE OR MORE DIAGNOSTIC TROUBLE CODE (DTC), LISTED IN THE TABLE BELOW AND RELEVANT TO THE HEATED OXYGEN SENSORS (HO2S), MAY BE STORED IN THE ENGINE CONTROL MODULE (ECM).

ENGAGED WHEN COMING TO A STOP OR IMMEDIATELY AFTER AN AUTOMATIC ENGINE RESTART (WHEN INTELLIGENT STOP/START IS ACTIVE). THE INSTRUMENT CLUSTER HAS SWITCHED OFF AFTER AN AUTOMATIC ENGINE STOP AND DRIVER EXIT CONDITIONS DO NOT EXIST AND THE VEHICLE DOES NOT AUTOMATICALLY RESTART THE ENGINE UPON RELEASE OF THE BRAKE PEDAL (NOTE. DTC P162F-00 MAY BE STORED IN THE ENGINE CONTROL MODULE [ECM]).

UPON DIAGNOSIS, INCLUDING REMOVAL OF THE AIR SPRING AND INVERTING IT FOR A PERIOD OF APPROXIMATELY ONE MINUTE, HYDRAULIC FLUID IS FOUND TO FLOW FROM THE AIR SUSPENSION PIPE 'VOSS' CONNECTOR."

STARVATION."

RESTARTS IN XXX MILES/KM, DIESEL EXHAUST FLUID DOSING MALFUNCTION WARNING MESSAGE DISPLAYED WITHIN THE INSTRUMENT CLUSTER MESSAGE CENTRE AND DTCS P20E8-84/85 AND P2BAE/P2BAF STORED IN THE PCM (POWERTRAIN CONTROL MODULE). NOTE: IF OTHER CODES ARE STORED IN THE PCM THEY MUST BE INVESTIGATED AND RESOLVED BEFORE FOLLOWING THE ADVICE DETAILED IN THIS SSM. CAUSE: THE SYSTEM HAS DETECTED A PRESSURE DEVIATION IN THE DEF (DIESEL EXHAUST FLUID) INJECTION SYSTEM."

STORED IN THE POWERTRAIN CONTROL MODULE (PCM) CAUSE: THIS MAY BE CAUSED BY A PCM SOFTWARE ISSUE (CPU RESPONSE TIME ERROR DURING VEHICLE SHUTDOWN PROCEDURE)."

THE MAIN DRIVING MANOEUVRES ASSOCIATED WITH THIS ARE: 1. STEERING RIGHT AND THEN HITTING A BUMP/RIDGE IN THE ROAD VERY SOON AFTER. 2. STEERING TO THE RIGHT AND THEN SHARPLY STEERING TO THE LEFT. CAUSE: THIS IS CAUSED BY THE FLUID MOVING WITHIN THE DYNAMIC RESPONSE VALVE BLOCK COMBINED WITH RAPID SYSTEM PRESSURE CHANGES."

THE MAIN DRIVING MANOEUVRES ASSOCIATED WITH THIS ARE: 1. STEERING RIGHT AND THEN HITTING A BUMP/RIDGE IN THE ROAD VERY SOON AFTER. 2. STEERING TO THE RIGHT AND THEN SHARPLY STEERING TO THE LEFT. CAUSE: THIS IS CAUSED BY THE FLUID MOVING WITHIN THE DYNAMIC RESPONSE VALVE BLOCK COMBINED WITH RAPID SYSTEM PRESSURE CHANGES."

TYRE PRESSURE MONITORING SYSTEM (TPMS) WARNING MESSAGES. CUSTOMERS AND RETAILERS HAVE BEEN UNABLE TO RE-INFLATE AND MAINTAIN SERVICE PRESSURES DUE TO LEAKAGE FROM THE TPMS VALVES. ISSUE MAY AFFECT: 15MY AND 16MY RANGE ROVER EVOQUE, DISCOVERY SPORT, RANGE ROVER (ALL NEW), DISCOVERY 4/LR4, RANGE ROVER SPORT VEHICLES. CAUSE: RETAILER TECHNICIANS HAVE OBSERVED TPMS VALVES WHERE THERE IS EVIDENCE OF AIR LOSS OR LEAKAGE FROM THE BASE OF THE VALVE STEM OR THROUGH THE TPMS VALVE CORE ."

CAUSE: THIS MAY BE CAUSED BY DUST AND/OR WATER INGRESS TO THE ACCESSORY DRIVE BELT IDLER PULLEY BEARING."

THE NOISE MAY BE MORE NOTICEABLE WHEN THE ENGINE IS AT IDLE SPEED AND WHEN THE ENGINE IS COLD. CAUSE: THIS MAY BE CAUSED BY A NOISY HIGH PRESSURE FUEL PUMP OUTLET VALVE."

RESTARTS IN XXX MILES, DIESEL EXHAUST FLUID DOSING MALFUNCTION WARNING MESSAGE DISPLAYED WITHIN THE INSTRUMENT CLUSTER MESSAGE CENTER AND DTCS P208B-00/P2BAE-00/P2BAF-00 STORED IN THE PCM (POWERTRAIN CONTROL MODULE) CAUSE: AIR IN THE SYSTEM."

TURBOCHARGER ON VEHICLES EQUIPPED WITH THE 3.0 TDV6 ENGINE LEADING TO TURBOCHARGER REPLACEMENTS. CAUSE: ENGINE LEAKING OIL FROM VARIOUS OTHER AREAS."

MODULE (PCM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE."

(ECM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

CAUSE: THIS MAY BE CAUSED DUE TO THE POTENTIAL FOR THE BLOWER MOTOR TO HIT THE UPPER LIMIT FOR CURRENT AND CUT OUT WHEN THE CLIMATE CONTROL IS ON MAXIMUM OR IF THE BLOWER MOTOR IS MANUALLY PUT TO MAXIMUM. THE ISSUE IS INTERMITTENT BECAUSE IT IS HIGHLY DEPENDENT ON THE STATE OF CHARGE OF THE BATTERY AND THE INPUTS TO THE SYSTEM. BLOWER MOTOR OPERATION CAN BE RESET BY EITHER CYCLING THE IGNITION OFF/ON OR BY CYCLING THE CLIMATE CONTROL OFF/ON MANUALLY."

MAY NOT RE-START AND THE IGNITION WILL TURN OFF. CAUSE: THIS MAY BE CAUSED BY AN ANTI-LOCK BRAKING SYSTEM (ABS) SOFTWARE, WHICH UNDER VERY SPECIFIC CIRCUMSTANCES CAN CAUSE THIS ISSUE TO OCCUR."

INVOLUNTARILY ENGAGED WHEN COMING TO A STOP OR IMMEDIATELY AFTER AN AUTOMATIC ENGINE RESTART (WHEN INTELLIGENT STOP/START IS ACTIVE)."

BOTH TOWING EYE COVERS ARE INCORRECT SPECIFICATION CAUSE: CURRENTLY UNDER INVESTIGATION AND ENGINEERING"

CUSTOMERS OR EXTERNAL INFLUENCES SUCH AS CAR WASHES MAY INADVERTANTLY KNOCK THE DOOR MIRROR HEAD INTO THE FOLDED POSITION, THIS WILL THEN CAUSE THE MIRROR HEAD TO BE LOOSE"

ENGINE AND THE ENGINE WILL NOT START. CAUSE: THIS MAY BE CAUSED BY ICE ON THE SOLENOID CONTACTS."

CAUSE: THIS MAY BE CAUSED BY DUST AND/OR WATER INGRESS TO THE PRIMARY DRIVE BELT IDLER PULLEY BEARING."

INSTRUMENT CLUSTER FOR A SHORT PERIOD DURING A KEY THROUGH ENGINE START (NOT TURNING ON IGNITION BEFORE ATTEMPTING TO START). VEHICLES AFFECTED (GASOLINE ONLY): L405 2015 MODEL YEAR AJ126SC L405 2015 MODEL YEAR AJ133SC L494 2015 MODEL YEAR AJ126SC L494 2015 MODEL YEAR AJ133SC CAUSE: CAN TIMING ERROR BETWEEN BCM, ECM AND INSTRUMENT CLUSTER."

INSTRUMENT CLUSTER: FAULTY GENERATOR FAULTY BATTERY MONITORING SYSTEM (BMS) THE CHARGE WARNING INDICATOR IS ILLUMINATED WHEN THE ENGINE IS RUNNING. CAUSE: THE POWER SUPPLY IS A FULLY INTEGRATED SYSTEM THAT REQUIRES SDD TO DIAGNOSE OVERALL FUNCTIONALITY ROBUSTLY TO MAKE SURE CUSTOMER SATISFACTION IS MET VIA RIGHT FIRST TIME DIAGNOSIS."

MODULE (PCM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE.

DIAGNOSTIC TROUBLE C ODES (DTC ) C 1A13-64, C 1A36-01, AND/OR C 1A24-67 MAY BE STORED. CAUSE: THIS MAY BE CAUSED BY THE EXHAUST VALVE WITHIN THE AIR SUSPENSION SYSTEM COMPRESSOR 'STICKING' DUE TO MANUFACTURING ISSUES."

THOUGH THE TRANSMISSION CONTROL SWITCH HAS NOT BEEN MOVED. THE TRANSMISSION GEAR POSITION INDICATOR ON THE GEAR SELECTOR AND IN THE INSTRUMENT CLUSTER MESSAGE CENTER MAY BE FLASHING 'D' OR 'S'. IF THE ENGINE IS STOPPED AND RESTARTED AND THEN DRIVE (D) OR SPORT (S) IS SELECTED, VEHICLE OPERATION RETURNS TO NORMAL."

UPON DIAGNOSIS, THE TECHNICIAN MAY FIND ONE OR MORE DIAGNOSTIC TROUBLE C ODE (DTC ), LISTED IN THE TABLE BELOW AND RELEVANT TO THE HEATED OXYGEN SENSORS (HO2S), MAY BE STORED IN THE ENGINE CONTROL MODULE (ECM). CAUSE: THIS MAY BE CAUSED BY THERMAL SHOCK WHEN WATER CONTACTS THE HEATED SENSING ELEMENT."

(ECM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE.

UPON DIAGNOSIS, THE TECHNICIAN MAY FIND ONE OR MORE DIAGNOSTIC TROUBLE CODE (DTC), LISTED IN THE TABLE BELOW AND RELEVANT TO THE HEATED OXYGEN SENSORS (HO2S), MAY BE STORED IN THE ENGINE CONTROL MODULE (ECM). CAUSE: THIS MAY BE CAUSED BY THERMAL SHOCK WHEN WATER CONTACTS THE HEATED SENSING ELEMENT."

DISCOVERY 4/LR4 (L319) AND RANGE ROVER SPORT (L320) ONLY. 10 MODEL YEAR ONWARDS. CAUSE: JLR ENGINEERING ARE CURRENTLY INVESTIGATING TO UNDERSTAND ANY SITUATIONS WHERE THE STEERING COLUMN IS THE CAUSE OF NOISE WHEN TURNING."

THE TECHNICIAN WILL EVALUATE IT AS FOLLOWS: THE AIR TEMPERATURE EMITTED FROM THE FACE VENT OUTLETS MAY CYCLE BETWEEN VERY COLD AND WARM EVERY 1-2 MINUTES. THE AIR TEMPERATURE EMITTED FROM THE FACE VENT OUTLETS MAY EXHIBIT AN INTERMITTENT FAULT, BLOWING WARM AIR CONSISTENTLY, THEN AFTER RESTARTING THE VEHICLE OR AFTER USING INCREASED ENGINE SPEED, WILL WORK NORMALLY AND BLOW COOL AIR. CAUSE: THIS MAY BE CAUSED BY THE COMPRESSOR NOT BEING TO THE CORRECT SPECIFICATION."

THOUGH THE TRANSMISSION CONTROL SWITCH HAS NOT BEEN MOVED. THE TRANSMISSION GEAR POSITION INDICATOR ON THE GEAR SELECTOR AND IN THE INSTRUMENT CLUSTER MESSAGE CENTER MAY BE FLASHING 'D' OR 'S'. IF THE ENGINE IS STOPPED AND RESTARTED AND THEN DRIVE (D) OR SPORT (S) IS SELECTED, VEHICLE OPERATION RETURNS TO NORMAL."

2) NOISE EVIDENT FROM THE FRONT AXLE TUBE ASSEMBLY. CAUSE: CURRENTLY UNDER INVESTIGATION."

THE SOUND MAY BE NOTICEABLE, WHEN ONE OF THE FRONT WHEELS TRAVELS OVER A UNEVEN SURFACE WHILE THE OPPOSITE FRONT WHEEL REMAINS ON A SMOOTH SURFACE. CAUSE: THIS MAY BE CAUSED BY THE OPERATION OF THE DYNAMIC RESPONSE SYSTEM ACTUATORS."

CAUSE: THERE ARE CURRENTLY 3 KNOWN POTENTIAL CAUSES UNDER INVESTIGATION: THE CHARGE AIR COOLANT PUMP, A PCM LOGIC CONCERN AND/OR SENSOR DEFECT."

A COOLANT LEAK IS FOUND FROM THE SEAM ON COOLANT PIPE (LR018275). SEE THE ATTACHED FILE FOR AN EXAMPLE OF THE LEAK LOCATION. CAUSE: A PROCESS ISSUE AT COMPONENT SUPPLIER."

VEHICLES FITTED WITH THE 3.0L SC V6 ENGINE WHERE THE ENGINE MALFUNCTION INDICATOR LAMP (MIL) IS ILLUMINATED WITH DIAGNOSTIC TROUBLE CODE (DTC) P25A2-00 STORED IN THE ENGINE CONTROL MODULE (ECM)."

ILLUMINATED WITH DIAGNOSTIC TROUBLE CODE (DTC) P25A2-00 STORED IN THE ENGINE CONTROL MODULE (ECM). ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

THOUGH THE TRANSMISSION CONTROL SWITCH HAS NOT BEEN MOVED. THE TRANSMISSION GEAR POSITION INDICATOR ON THE GEAR SELECTOR AND IN THE INSTRUMENT CLUSTER MESSAGE CENTER MAY BE FLASHING 'D' OR 'S'. IF THE ENGINE IS STOPPED AND RESTARTED AND THEN DRIVE (D) OR SPORT (S) IS SELECTED, VEHICLE OPERATION RETURNS TO NORMAL. CAUSE: THIS MAY BE CAUSED BY A TRANSMISSION CONTROL MODULE (TCM) SOFTWARE ISSUE."

ROVER (L405) VEHICLES WHERE A 'LOW COOLANT' WARNING IS ILLUMINATED ON THE INSTRUMENT CLUSTER DUE TO COOLANT LEAKING THROUGH THE LOWER PART OF THE COOLANT EXPANSION TANK. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

TO BE INSTALLED ON VEHICLES BUILT WITH THE PRIOR PART. CAUSE: THE VCT SOLENOID DESIGN CHANGED, AND THE ELECTRICAL CONNECTOR ON THE VCT SOLENOID IS A DIFFERENT SIZE."

ANALYSIS MANY ARE DEEMED AS NO FAULT FOUND. IT IS POSSIBLE DURING AN ECO STOP START THAT THE VEHICLE DOES NOT RE-START. CAUSE INCORRECT DIAGNOSIS"

'SOFT CLOSING', THE SOFT CLOSE LEVER IN THE DOOR LATCH MAY BLOCK THE RELEASE OF THE LATCH CLAW FROM THE DOOR STRIKER AND THUS PREVENT THE DOOR FROM OPENING EXTERNALLY. AS THE VEHICLE WILL BE IN TRANSPORT MODE ALL DOORS EXCEPT THE DRIVER'S DOOR WILL BE LOCKED, THEREFORE IF THIS ISSUE OCCURS THERE WILL BE NO EXTERNAL ACCESS VIA ANY OTHER DOOR TO ALLOW ACCESS TO THE HAZARD WARNING SWITCH TO WAKE THE CAR AND ALLOW THE DRIVER'S DOOR SOFT CLOSE MOTOR TO RECOVER. CAUSE: TRANSIT RELAY CUTS THE POWER TO THE SOFT CLOSE MOTOR CAUSING THE SOFT CLOSE LEVER IN THE DOOR LATCH TO BLOCK THE RELEASE OF THE LATCH CLAW FROM THE DOOR STRIKER AND THUS PREVENT THE DOOR FROM OPENING UNTIL THE HAZARD WARNING SWITCH IS PRESSED. THE SOFT CLOSE MOTOR IS A STANDALONE MODULE AND THEREFORE DOES NOT RECEIVE TRANSPORT MODE IN ORDER TO INHIBIT OPERATION DURING TRANSPORT."

DISPLAYED IN THE INSTRUMENT CLUSTER AND THE TRANSMISSION DEFAULTS TO FIXED GEAR 'LIMP-HOME' MODE. DIAGNOSTIC TROUBLE CODE (DTC) P07DC-07, P07DD-07, AND/OR P2702-07 MAY BE STORED IN THE TRANSMISSION CONTROL MODULE (TCM). CAUSE: THIS MAY BE CAUSED BY A SOFTWARE ERROR CAUSING EITHER A 'STUCK IN FIRST GEAR' CONDITION OR A FAILURE TO DISENGAGE C CLUTCH PRESSURE, RESULTING IN CLUTCH SLIP AND ANY OF THE LISTED DTCS BEING STORED."

DISPLAYED IN THE INSTRUMENT CLUSTER; ENGINE FAILS TO CRANK; VEHICLE MAY NOT UNLOCK / LOCK WHEN USING PASSIVE ENTRY OR WHEN PRESSING A SMART KEY BUTTON. CAUSE: THIS MAY BE CAUSED BY A 'LOCK UP' OF THE KEYLESS VEHICLE MODULE (KVM)."

OF TIME OR A LOW COOLANT LEVEL MESSAGE IS DISPLAYED IN THE MESSAGE CENTER. UPON INSPECTION, A LEAK MAY BE FOUND TO BE FROM THE FRONT OF THE ENGINE-DRIVEN COOLANT PUMP, TOGETHER WITH EXCESSIVE WEAR OF THE COOLANT PUMP BEARING."

THIS CAN LEAD TO THE ENGINE CHECK WARNING LAMP BEING ILLUMINATED WITH AN ASSOCIATED DTC RELEVANT TO AN EVAP SYSTEM LEAK, I.E. DTC P0442-00. CAUSE: A NEW FUEL FILLER NECK AND ASSOCIATED FUEL CAP WAS INTRODUCED AT 2015MY FOR L405 AND L494 NAS ONLY."

THIS CAN LEAD TO THE ENGINE CHECK WARNING LAMP BEING ILLUMINATED WITH AN ASSOCIATED DTC RELEVANT TO AN EVAP SYSTEM LEAK, I.E. DTC P0442-00. CAUSE: A NEW FUEL FILLER NECK AND ASSOCIATED FUEL CAP WAS INTRODUCED AT 2015MY FOR L405 AND L494 NAS ONLY."

(L494) VEHICLES FITTED WITH THE 3.0L SC V6 ENGINE WHERE THE ENGINE CONNECTING ROD SECURING BOLTS MAY NOT BE TO THE CORRECT TORQUE SPECIFICATION."

SEE ATTACHED PHOTOS FOR EXAMPLES OF THE CONCERN. THE SPLIT CAN BE FOUND ANYWHERE AROUND THE CIRCUMFERENCE OF THE PISTON, ALTHOUGH MOST LIKELY TO BE SEEN THROUGH THE CALIPER WINDOW ADJACENT TO THE PISTON. CAUSE. CURRENTLY UNDER INVESTIGATION."

WITHOUT ANY RELATED CUSTOMER SYMPTOMS. CAUSE: OVER SENSITIVE DTC U0126-87 FOR ABS MODULE ON V6 AND V8 PETROL SUPERCHARGER DERIVATIVES ONLY"

CAUSE: THERE ARE A NUMBER OF POTENTIAL CAUSES WHICH ENGINEERING WISH TO INVESTIGATE FURTHER"

ACTION: PLEASE REFER TO THE PROCEDURE BELOW FOR INFORMATION ON HOW TO ACCESS THE NEW INFORMATION THROUGH SDD."

THE NOISE MAY BE MORE NOTICEABLE WHEN THE ENGINE IS AT IDLE SPEED AND WHEN THE ENGINE IS COLD. CAUSE: THIS MAY BE CAUSED BY A NOISY HIGH PRESSURE FUEL PUMP OUTLET VALVE."

DISCOVERY 4/LR4 (L319) AND RANGE ROVER SPORT (L320) ONLY. 10 MODEL YEAR ONWARDS. CAUSE: JLR ENGINEERING ARE CURRENTLY INVESTIGATING TO UNDERSTAND ANY SITUATIONS WHERE THE STEERING COLUMN IS THE CAUSE OF NOISE WHEN TURNING.

CAUSE: LEAK FROM THE WAGNER/STEERING GEAR DAMPING VALVE OR SEALING WASHER (SEE ATTACHED PHOTO'S)"

BEEN INCORRECTLY CHANGED FOR KNOCK ISSUES WHEN THE FRONT BUSH IS CRACKED AND SHOULD HAVE BEEN REPLACED AS PER TECHNICAL SERVICE BULLETINS LTB00204V4 AND LTB00123V4. CAUSE: INCORRECT DIAGNOSIS OF FRONT AND REAR BUSH ISSUES. SEE ATTACHED PHOTO SHOWING AN EXAMPLE OF A CRACKED FRONT BUSH."

ILLUMINATED WITH DIAGNOSTIC TROUBLE CODE (DTC) P25A2-00 STORED IN THE ENGINE CONTROL MODULE (ECM). ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

THE NOISE MAY BE MORE NOTICEABLE WHEN THE ENGINE IS AT IDLE SPEED AND WHEN THE ENGINE IS COLD. CAUSE: THIS MAY BE CAUSED BY A NOISY HIGH PRESSURE FUEL PUMP OUTLET VALVE."

WITHOUT ANY RELATED CUSTOMER SYMPTOMS . CAUSE: OVER SENSITIVE DTC U0126-87 FOR ABS MODULE ON V6 AND V8 PETROL SUPERCHARGER DERIVATIVES ONLY"

CAUSE: THERE ARE A NUMBER OF POTENTIAL CAUSES WHICH ENGINEERING WISH TO INVESTIGATE FURTHER"

ACTION: PLEASE REFER TO THE PROCEDURE BELOW FOR INFORMATION ON HOW TO ACCESS THE NEW INFORMATION THROUGH SDD."

ILLUMINATED WITH DIAGNOSTIC TROUBLE CODE (DTC) P25A2-00 STORED IN THE ENGINE CONTROL MODULE (ECM). ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

SPORT (L494) AND RANGE ROVER (L405) VEHICLES (5.0L S/C V8 ONLY) WITHIN THE LISTED VIN RANGES. UNEXPECTED BODY MOVEMENTS WHEN THE VEHICLE IS STATIONARY MAY BE EXPERIENCED DUE TO THE SYSTEM SELF-TEST PULSE RESULTING IN PRESSURE IN THE ACTUATORS WHICH IS NORMALLY ISOLATE FROM THEM. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

DISCOVERY 4/LR4 (L319) AND RANGE ROVER SPORT (L320) ONLY. 10 MODEL YEAR ONWARDS. CAUSE: JLR ENGINEERING ARE CURRENTLY INVESTIGATING TO UNDERSTAND ANY SITUATIONS WHERE THE STEERING COLUMN IS THE CAUSE OF NOISE WHEN TURNING."

A COOLANT LEAK IS FOUND FROM THE SEAM ON COOLANT PIPE (LR018275). SEE THE ATTACHED FILE FOR AN EXAMPLE OF THE LEAK LOCATION. CAUSE: A PROCESS ISSUE AT COMPONENT SUPPLIER."

INDUCTION / FUEL INJECTION CLEANING EQUIPMENT OR MATERIALS. THIS INCLUDES, BUT IS NOT LIMITED TO, ""VACU-FLUSH"" TYPE EQUIPMENT. CAUSE: THE USE OF NON-APPROVED EQUIPMENT CAN CAUSE THE ENGINES TO HYDRO-LOCK, OR CAUSE OTHER ENGINE DAMAGE, AND SOMETIMES THE ONLY POSSIBLE REPAIR IS TO REPLACE THE ENGINE."

CAUSE: THIS MAY BE CAUSED BY TORSIONAL ISOLATOR AND/OR THE TORSIONAL ISOLATOR SPRING SUPPORT SHAFT WEAR CAUSING EXCESSIVE BACKLASH IN THE SUPERCHARGER DRIVE."

THIS MAYBE ACCOMPANIED WITH THE COOLANT GAUGE READING HIGH AND/OR THE CHARGE WARNING INDICATOR ILLUMINATED. INVESTIGATION FINDS A CONCERN WITH THE PRIMARY IDLER PULLEY ASSEMBLY WHICH IN SOME CASES CAN LEAD TO DAMAGE OF THE PRIMARY DRIVE BELT. THE PRIMARY BELT DRIVES THE COOLANT PUMP AND GENERATOR HENCE THE POTENTIAL FOR THE COOLANT GAUGE TO READ HIGH AND/OR THE CHARGE WARNING INDICATOR ILLUMINATING IF THE BELT IS DAMAGED AND NOT FUNCTIONING CORRECTLY. THIS CONCERNS AFFECTS LTIS (LOW TIME IN SERVICE) VEHICLES WITH THE 3.0 AJ126 AND 5.0 AJ133 GASOLINE ENGINES FITTED.

UPON DIAGNOSIS, INCLUDING REMOVAL OF THE AIR SPRING AND INVERTING IT FOR A PERIOD OF APPROXIMATELY ONE MINUTE, HYDRAULIC FLUID IS FOUND TO FLOW FROM THE AIR SUSPENSION PIPE 'VOSS' CONNECTOR.

ON HIGH PRESSURE FUEL PUMP DIAGNOSTICS. *PE

NOT MOVED, OR GEAR POSITION INDICATOR ON INSTRUMENT CLUSTER MESSAGE IS FLASHING D OR S AND WOULD HAVE NORMAL OPERATION ONCE ENGINE IS STOPPED AND RESTARTED. *PE UPDATED 9/25/15. *PE

center and DTC U2000-4B logged within the Rear Differential Control Module (RDCM).

The error message The following error was encountered: is displayed to the user.

leading to unnecessary replacement of the air suspension compressor. Please note that the DTCs do not generate an air suspension fault on the instrument cluster or display any vehicle symptoms.

leading to unnecessary replacement of the air suspension compressor. Please note that the DTCs do not generate an air suspension fault on the instrument cluster or display any vehicle symptoms.

Master Controller (IMC) may show that the module is still not up to date.

Initial diagnosis shows no fault found or no measurable quiescent drain.

no longer work

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341-00 and P054A-00 will be stored within the Powertrain Control Module (PCM).

Master Controller (IMC) may show that the module is still not up to date.

Initial diagnosis shows no fault found or no measurable quiescent drain.

no longer work

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341-00 and P054A-00 will be stored within the Powertrain Control Module (PCM).

Examples of these may include: Exterior lighting, Interior lighting, Sun roof blinds, Steering Wheel Adjust, Eco stop start etc... One or more of these symptoms may be accompanied by DTC U1000-00 (Solid State Driver Protection Active - Driver Disabled) present in the BCM. If DTC U1000-00 is not present in the BCM do not continue with this SSM. Continue to diagnose and repair the inoperative BCM output as necessary using Topix as a guide.

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341- 00, P054A-00, P0303-00 and P0302-00 will be stored within the Powertrain Control Module (PCM).

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341- 00, P054A-00, P0303-00 and P0302-00 will be stored within the Powertrain Control Module (PCM).

diagnostic trouble code (DTC) U3000-05 logged in the Chassis Control Module (CHCM) Vehicle suspension is in tight tolerance mode

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

module using Pathfinder or Symptom Driven Diagnostics (SDD) the module appears to be unresponsive to any further diagnostic commands or smart key remote operation.

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

module using Pathfinder or Symptom Driven Diagnostics (SDD) the module appears to be unresponsive to any further diagnostic commands or smart key remote operation.

message centre, when the vehicle ignition is switched on after the vehicle has been parked overnight. In addition a clicking noise may be heard from the Rear Junction Box when the ignition is switched on.

(HLDF) on occasions may fail to download software correctly resulting in no communications with the module and blank screen.

The concern prevents the technician from using Pathfinder to diagnose or rectify concerns with the ATCM

section 418-02 - Description and Operation ? Diagnosis and Testing) for the updated wiring repair standard and guidelines.

Retailers are testing the primary battery using the Midtronics EXP-1080 tester which is reporting the battery is serviceable. The vehicle then returns with the same Customer concern of ECO Stop/Start inoperative. If a Midtronics GRX-3080 is used, the primary battery fails the test. Replacement of the primary battery resolves the concern.

This will result in the Telematics Service Provider contacting the customer to confirm if theft has occurred. Until the customer confirms that no theft has occurred, they will be blocked from using various InControl features.

(IC) for less than one second when no service is required. Cause: This may be caused by a discrepancy between the values in the Powertrain Control Module (PCM) and the IC for next service initialization.

center and DTC U2000-4B logged within the Rear Differential Control Module (RDCM).

center and DTC U2000-4B logged within the Rear Differential Control Module (RDCM).

center and DTC U2000-4B logged within the Rear Differential Control Module (RDCM).

center and DTC U2000-4B logged within the Rear Differential Control Module (RDCM).

recorded in the Side Object Detection Left (SODL) or Side Object Detection Right(SODR) without any customer impact on the Blind Spot Monitor features.

(DTC) B12BD-31 "Rear Camera - No Signal" and or U1A4B-49 "Control Module Processor B - Internal Failure" stored in the Image Processing Module B (IPMB). The DTC is a false flagging code that can lead to incorrect diagnosis of any camera related issue reported by the customer.

Heating Ventilation Air Conditioning (HVAC) vents when the temperatures selected on the front integrated control panel are set to the same value. During diagnosis using Pathfinder it may be evident that there are no Diagnostic Trouble Codes (DTCs) stored in the (HVAC) module.

For example Transportation Mode Enable. Or Deployable Side Steps Add/Remove function fails after SSM73100 (PATHFINDER fails to add Deployable Side Steps or displays an error when updating module software) has been referred to.

Vehicle where the Gateway Module (GWM) stays awake and keeps the Controller Area Network (CAN) awake. This constant current drain of 3 amps causes the battery to go flat within a few days.

the Gateway Module (GWM) stays awake and keeps the Controller Area Network (CAN) awake. This constant current drain of three (3) amps causes the battery to go flat within a few days.

Following diagnosis using Pathfinder the diagnostic trouble Code (DTC) U3000-04 ?Control module System Internal Failure? is stored in the Chassis Control Module (CHCM)

Following diagnosis using Pathfinder the diagnostic trouble Code (DTC) U3000-04 ?Control module System Internal Failure? is stored in the Chassis Control Module (CHCM).

Display Front (HLDF) may be wrongly replaced when troubleshooting, if issues are incorrectly attributed to it.

(DTC) B12BD-31 ?Rear Camera - No Signal? and or U1A4B-49 ?Control Module Processor B ? Internal Failure? stored in the Image Processing Module B (IPMB). The DTC is a false flagging code that can lead to incorrect diagnosis of any camera related issue reported by the customer.

For example Transportation Mode Enable. Or Deployable Side Steps Add/Remove function fails after SSM73100 (PATHFINDER fails to add Deployable Side Steps or displays an error when updating module software) has been referred to.

Affected Vehicle where the Gateway Module (GWM) stays awake and keeps the Controller Area Network (CAN) awake. This constant current drain of 3 amps causes the battery to go flat within a few days.

the Gateway Module (GWM) stays awake and keeps the Controller Area Network (CAN) awake. This constant current drain of three (3) amps causes the battery to go flat within a few days.

Heating Ventilation Air Conditioning (HVAC) vents when the temperatures selected on the front integrated control panel are set to the same value. During diagnosis using Pathfinder it may be evident that there are no Diagnostic Trouble Codes (DTCs) stored in the (HVAC) module.

EITHER OF THE TWO ISSUES BELOW CAN OCCUR: THE DIAGNOSTIC TROUBLE CODES (DTCS) U2300-62 OR U2300-54 IS STORED IN THE BODY CONTROL MODULE (BCM). THE CCF LOADED INTO THE BCM CONTAINS FOUR CRITICAL MISMATCHES RELATED TO THE CCF ASSEMBLIES FOR DIFFERENT MODULES.

START UNAVAILABLE.

START UNAVAILABLE.

MESSAGE CENTRE, WHEN THE VEHICLE IGNITION IS SWITCHED ON AFTER THE VEHICLE HAS BEEN PARKED OVERNIGHT. IN ADDITION A CLICKING NOISE MAY BE HEARD FROM THE REAR JUNCTION BOX WHEN THE IGNITION IS SWITCHED ON. CAUSE: SOFTWARE CALCULATION."

THE FOLLOWING DTCS MAY ALSO BE LOGGED: EPAS DTCS LOGGED: -B1304-16: ELECTRONIC POWER ASSISTED STEERING (EPAS) SYSTEM CIRCUIT VOLTAGE BELOW THRESHOLD -U3001-00: POWER STEERING CONTROL MODULE (PSCM) SYSTEM IMPROPER SHUTDOWN. THESE MAY BE ACCOMPANIED BY: -U0001-87 / 88 HIGH SPEED CAN BUS INVALID SERIAL DATA RECEIVED / MISSING MESSAGE. CHCM DTCS LOGGED: -U0131-00 CHASSIS CONTROL MODULE (CHCM) LOST COMMS WITH PSCM. -U3003-62 BATTERY VOLTAGE SIGNAL COMPARE FAILURE. -U0420-68 CHCM INVALID DATA RECEIVED FROM PSCM. CAUSE: THIS MAY BE CAUSED BY: -LOW BATTERY VOLTAGE. -WIRING HARNESS ISSUE (SHORT / OPEN CIRCUIT, HIGH RESISTANCE). -HIGH RESISTANCE AT EPAS EARTH TERMINAL (FOR L405/L494) G1D132 AND OR G4D178, (SEE ATTACHED DIAGRAM). OR IF ON L550/L538 HIGH RESISTANCE AT G1D122A, G1D122B, G1D122AZ AND G1D108. -POOR CONNECTION OR PIN SET CONDITION AT CONNECTOR NUMBER: C11-G1"

ONE OR MORE OF THE FOLLOWING SYMPTOMS MAY ALSO BE EVIDENT: NO AUDIO SOUND SPEAKER INTERFERENCE TOUCH SCREEN INOPERATIVE OR 'FREEZING' CAUSE: THIS MAY BE CAUSED BY THE CLIMATE CONTROL SYSTEM DRAIN TUBE BEING INCORRECTLY LOCATED IN FOOTWELL CAUSING WATER CONTAMINATION TO THE CARPETS AND POSSIBLE WATER INGRESS INTO THE AUDIO AMPLIFIER MODULE."

KEYLESS VEHICLE MODULE - KVM ON SDD) ON EITHER A RANGE ROVER (ALL NEW) - L405 OR RANGE ROVER SPORT - L494 14 TO 15 MY THAT HAS A HARDWARE PART NUMBER PREFIX OF 'FK72', SDD WILL RESOLVE THE INCORRECT SOFTWARE AND THE SOFTWARE DOWNLOAD WILL FAIL. CAUSE: SOME FILES USED BY SDD TO RESOLVE THE REQUIRED SOFTWARE HAVE BEEN INCORRECTLY CHANGED. THIS MEANS SDD SELECTS THE INCORRECT SOFTWARE PARTS FOR FK72 PART RFA."

FROM 14MY ONWARDS L550 LAND ROVER SPORT: FROM 15MY ONWARDS WHEN FITTING A NEW REMOTE FUNCTION ACTUATOR (RFA) (REFERRED TO AS THE KEYLESS VEHICLE MODULE - KVM ON SDD) WITH A MODULE PART NUMBER OF: FK72-19H440 - AE FK72-19H440 - BE FK72-19H440 - AF FK72-19H440 - BF SDD CANNOT COMMUNICATE WITH THE RFA. THIS WILL BE DISPLAYED AS A RED X FOR THE RFA IN THE SDD VEHICLE SPECIFICATION SCREEN. CAUSE: THE NEW RFA MODULE SUPPLIED IS MANUFACTURED WITH PRE-FLASHED SOFTWARE FOR DUAL CAN VEHICLES. THESE VEHICLES ARE MULTICAN AND NOT DUAL CAN AND WILL NOT COMMUNICATE WITH SDD FOR PROGRAMMING OR UPDATE WITHOUT COMPLETING THE ACTION INSTRUCTIONS DETAILED BELOW."

THE FOLLOWING DTCS MAY ALSO BE LOGGED: EPAS DTCS LOGGED: -B1304-16: ELECTRONIC POWER ASSISTED STEERING (EPAS) SYSTEM CIRCUIT VOLTAGE BELOW THRESHOLD -U3001-00: POWER STEERING CONTROL MODULE (PSCM) SYSTEM IMPROPER SHUTDOWN. THESE MAY BE ACCOMPANIED BY: -U0001-87 / 88 HIGH SPEED CAN BUS INVALID SERIAL DATA RECEIVED / MISSING MESSAGE. CHCM DTCS LOGGED: -U0131-00 CHASSIS CONTROL MODULE (CHCM) LOST COMMS WITH PSCM. -U3003-62 BATTERY VOLTAGE SIGNAL COMPARE FAILURE. -U0420-68 CHCM INVALID DATA RECEIVED FROM PSCM. CAUSE: THIS MAY BE CAUSED BY: -LOW BATTERY VOLTAGE. -WIRING HARNESS ISSUE (SHORT / OPEN CIRCUIT, HIGH RESISTANCE). -HIGH RESISTANCE AT EPAS EARTH TERMINAL (FOR L405/L494) G1D132 AND OR G4D178, (SEE ATTACHED DIAGRAM). OR IF ON L550/L538 HIGH RESISTANCE AT G1D122A, G1D122B, G1D122AZ AND G1D108."

RETURNED TO THE SUPPLIER (DENSO) TO INVESTIGATE FOR POSSIBLE DEFECTS."

(IC) FOR LESS THAN ONE SECOND WHEN NO SERVICE IS REQUIRED. CAUSE: THIS MAY BE CAUSED BY A DISCREPANCY BETWEEN THE VALUES IN THE POWERTRAIN CONTROL MODULE (PCM) AND THE IC FOR NEXT SERVICE INITIALIZATION."

EXHIBIT INTERMITTENT OPERATION, CAUSING ONE OR MORE OF THE FOLLOWING ISSUES: AUDIO VOLUME WILL NOT ADJUST (UP AND/OR DOWN) RADIO SEEK BUTTONS WILL NOT OPERATE VOLUME CONTROL BUTTONS CAUSE THE RADIO STATION TO CHANGE THE INFOTAINMENT SYSTEM IS SLOW TO OPERATE (BLANK SCREEN FOLLOWED BY THE 'LAND ROVER' LOGO) DIAGNOSTIC TROUBLE CODE (DTC) U2013-02, 'SWITCH PACK, GENERAL SIGNAL FAILURE', IS STORED IN THE INSTRUMENT CLUSTER MEMORY DTC B1D21-13, 'REMOTE CONTROL SWITCH CIRCUIT OPEN', IS STORED IN THE TOUCH SCREEN MEMORY CAUSE: THIS MAY BE CAUSED BY POOR ELECTRICAL CONNECTION CONTINUITY."

INSTRUMENT CLUSTER FOR <1 SECOND (WHEN NO SERVICE IS REQUIRED). NO CUSTOMER SYMPTOMS UNTIL A SERVICE RESET HAS BEEN PERFORMED. WHEN AN ACTUAL SERVICE IS REQUIRED THE MESSAGE WILL APPEAR FOR 4 SECONDS AS DESIGN INTENT. CAUSE: DISTANCE TO NEXT SERVICE INITIALISATION VALUE MANAGEMENT BETWEEN ECM AND INSTRUMENT CLUSTER (FIRST 900MS)."

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE(TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE."

LOCKING (CDL) ISSUES WITH ONE OR MORE DOORS (BUT NOT THE TAILGATE[S]) MAY BE EVIDENT. CAUSE: THIS MAY BE CAUSED BY AN INCORRECT DOOR MODULE CONFIGURATION DURING THE VEHICLE MANUFACTURE."

RANGE ROVER SPORT (L494), AND RANGE ROVER (L405) VEHICLES WHERE THE BLINDSPOT MONITORING CONTROL MODULE (BMCM) MAY EXPERIENCE WATER INGRESS. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN"

MODULE PART NUMBER OF: FK72-19H440 - AE; FK72-19H440 - BE; FK72-19H440 - AF; FK72-19H440 - BF SDD CANNOT COMMUNICATE WITH THE RFA. THIS WILL BE DISPLAYED AS A RED X FOR THE RFA IN THE SDD VEHICLE SPECIFICATION SCREEN."

AREA OF THE TAILGATE HARNESS RUBBER SLEEVE.

ASSOCIATED COMPONENTS REPLACED FOR A NON-START CONDITION. FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORISED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

UPDATE REQUIRED"" IN THE STATUS OF THE SOFTWARE PART CONFIRMATION SCREEN. CAUSE: WHEN SDD IS USED TO UPDATE THE KVM FOR P068 AND THE KVM HAS A PREFIX OF FK72 THEN THE SOFTWARE REQUIRED TO UPDATE THE KVM IS NOT AVAILABLE TO COMPLETE P068 SUCCESSFULLY."

AND MAY STORE U2300-XX CENTRAL CONFIGURATION CODES. CAUSE: PARK ASSIST MODULE (PAM) SOFTWARE CONCERN."

IF BLOCKAGE OCCURS WHILE ACC IS BEING USED, DRIVER INTERVENE AND/OR ""RADAR SENSOR BLOCKED"" MESSAGE WILL APPEAR ON THE CLUSTER AND DTC C1A67-97 SET. BLOCKAGE CAN ALSO OCCUR WHEN ACC IS NOT BEING USED. CAUSE: ""RADAR SENSOR BLOCKED"" INDICATES THAT THE ADAPTIVE SPEED CONTROL SYSTEM'S VISIBILITY HAS BEEN REDUCED DUE TO AN OBSTRUCTION. ACC CONTINUALLY SCANS FOR OBJECTS AHEAD AND, IF IT SEES NO OBJECTS I.E. VEHICLES, ROAD SIGNS, LAMP POSTS, GUARD RAILS ETC., IT WILL INDICATE A BLOCKAGE EVEN IF THE ACC IS NOT USED. THE C1A67-97 DTC FLAGS A RADAR BLOCKAGE SITUATION AND NOT A SYSTEM FAULT."

NOTED IN THE AUXILIARY CONTROL MODULE (AUCM) DURING A SYMPTOM DRIVEN DIAGNOSTICS (SDD) FAULT CODE READ. CAUSE: SOFTWARE CALCULATION"

IF THE NAV BUTTON IS PRESSED A 2-5 SECOND PERIOD OF AM/ FM RADIO CAN BE HEARD AND THEN RETURNS BACK TO NO AUDIO. ISSUE WILL ONLY SELF-RECOVER AFTER AN IGNITION CYCLE. CAUSE: CURRENTLY UNDER ANALYSIS."

THEN RESTARTING AS IF THE IGNITION WAS CYCLED. THE LAND ROVER LOGO WILL APPEAR AND THE SYSTEM WILL FUNCTION NORMALLY AFTER THE RESET OCCURS. CAUSE TOUCH SCREEN SOFTWARE CONCERN."

CAUSE: THIS MAY BE CAUSED BY A SOFTWARE ERROR AND/OR CENTRAL PROCESSING UNIT (CPU) DATA OVERLOAD."

CAUSE: THIS MAY BE CAUSED BY A SOFTWARE ERROR IN THE STEERING WHEEL HEATER CONTROL MODULE (SWH)."

CLOSING FULLY OR NOT GOING FULLY DOWN WHEN OPENING. CUSTOMERS MAY REPORT A HARD CLOSE IS NOT OCCURRING UPON OPERATION CAUSE THE WINDOWS NEED TO LEARN THE END OF TRAVEL ON ALL SIDE DOOR WINDOW GLASS OPERATIONS. ONCE THE END OF THE GLASS TRAVEL HAS BEEN LEARNT THE DOOR CONTROL MODULES WILL THEN TAKE CONTROL OF THE SIDE DOOR WINDOW GLASS AND ADJUST THE SIDE GLASS STOP POSITION (UP & DOWN) TO LIMIT THE WINDOW MOVEMENT BEFORE THE END OF TRAVEL IS REACHED. THIS IS TO REDUCE THE WINDOW GLASS THUMPING THE END OF THE TRAVEL STOPS AND CAUSING CUSTOMER NVH DISSATISFACTION"

EXHIBIT INTERMITTENT OPERATION, CAUSING ONE OR MORE OF THE FOLLOWING ISSUES: AUDIO VOLUME WILL NOT ADJUST (UP AND/OR DOWN) RADIO SEEK BUTTONS WILL NOT OPERATE VOLUME CONTROL BUTTONS CAUSE THE RADIO STATION TO CHANGE THE INFOTAINMENT SYSTEM IS SLOW TO OPERATE (BLANK SCREEN FOLLOWED BY THE 'LAND ROVER' LOGO) DIAGNOSTIC TROUBLE CODE (DTC) U2013-02, 'SWITCH PACK, GENERAL SIGNAL FAILURE', IS STORED IN THE INSTRUMENT CLUSTER MEMORY DTC B1D21-13, 'REMOTE CONTROL SWITCH CIRCUIT OPEN', IS STORED IN THE TOUCH SCREEN MEMORY CAUSE: THIS MAY BE CAUSED BY POOR ELECTRICAL CONNECTION CONTINUITY"

COMPLETED: PRE DELIVERY INSPECTION (PDI) CONFIGURE NEW MODULE - INSTRUMENT CLUSTER CONTROL MODULE CAUSE: DURING THE APPLICATIONS AN ERROR IS PRESENTED ON SCREEN STATING: ERROR OPENING THE MDX DEFINITION FILE: MDX_IPC AFTER THE MESSAGE IS DISPLAYED, THE APPLICATIONS EXITS AND RETURNS TO THE RECOMMENDATION MENU."

FOR FAULT CODES LOGGED IN THE KVM (KEYLESS VEHICLE MODULE) ALSO KNOWN AS THE RFA (REMOTE FUNCTION ACTUATOR) F000-63/U3000-63, CONTROL MODULE - CIRCUIT/ COMPONENT PROTECTION TIME-OUT IS LOGGED. CAUSE THIS DTC IS SET WHEN THE KVM HAS GONE THROUGH A SELF RESET"

ASSOCIATED COMPONENTS REPLACED FOR A NON-START CONDITION. FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORISED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

INTERFACE MODULE (FCDIM) WHERE A VEHICLE DOES NOT HAVE THE BLIND SPOT MONITORING OPTION FITTED. CAUSE: CONFIGURATION MIS-MATCH BETWEEN FCDIM & VEHICLE CONFIGURATION FILE THAT MAY CAUSE DTCS U0233-00 LOST COMMUNICATION WITH THE RIGHT SIDE OBSTACLE DETECTION CONTROL MODULE & U0232-00 LOST COMMUNICATION WITH THE LEFT SIDE OBSTACLE DETECTION MODULE TO BE STORED UNNECESSARILY."

RANGE ROVER SPORT (L494), AND RANGE ROVER (L405) VEHICLES WHERE THE BLINDSPOT MONITORING CONTROL MODULE (BMCM) MAY EXPERIENCE WATER INGRESS"

RANGE ROVER SPORT (L494), AND RANGE ROVER (L405) VEHICLES WHERE THE BLINDSPOT MONITORING CONTROL MODULE (BMCM) MAY EXPERIENCE WATER INGRESS. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

THEN RESTARTING AS IF THE IGNITION WAS CYCLED. THE LAND ROVER LOGO WILL APPEAR AND THE SYSTEM WILL FUNCTION NORMALLY AFTER THE RESET OCCURS. CAUSE TOUCH SCREEN SOFTWARE CONCERN"

CAUSE: POOR CONNECTION AT THE CAMERA MODULE."

IF A BCM HAS BEEN DETERMINED TO REQUIRE REPLACEMENT FOLLOWING DIAGNOSIS, PLEASE CARRY OUT THE STEPS LISTED IN THE ACTION BELOW. CAUSE: CURRENTLY UNDER ANALYSIS."

CLOSING FULLY OR NOT GOING FULLY DOWN WHEN OPENING. CUSTOMERS MAY REPORT A HARD CLOSE IS NOT OCCURRING UPON OPERATION CAUSE THE WINDOWS NEED TO LEARN THE END OF TRAVEL ON ALL SIDE DOOR WINDOW GLASS OPERATIONS. ONCE THE END OF THE GLASS TRAVEL HAS BEEN LEARNT THE DOOR CONTROL MODULES WILL THEN TAKE CONTROL OF THE SIDE DOOR WINDOW GLASS AND ADJUST THE SIDE GLASS STOP POSITION (UP & DOWN) TO LIMIT THE WINDOW MOVEMENT BEFORE THE END OF TRAVEL IS REACHED. THIS IS TO REDUCE THE WINDOW GLASS THUMPING THE END OF THE TRAVEL STOPS AND CAUSING CUSTOMER NVH DISSATISFACTION"

ISSUE: A POTENTIAL CONCERN HAS BEEN IDENTIFIED WITH THE ACCELERATOR PEDAL ON A SMALL NUMBER OF RANGE ROVER AND RANGE ROVER SPORT VEHICLES WHICH MAY RESULT IN THE VEHICLE ENTERING RESTRICTED PERFORMANCE MODE. CAUSE: THE ACCELERATOR PEDAL SWITCH PRINTED CIRCUIT BOARD MAY NOT HAVE BEEN CORRECTLY SOLDERED LEADING TO AN INTERMITTENT CONNECTION."

LINE DISPLAY FRONT (HLDF), MAY BE WRONGLY REPLACED WHEN TROUBLESHOOTING IF ISSUES ARE INCORRECTLY ATTRIBUTED TO IT. CAUSE: THE TS MAY BE INCORRECTLY DIAGNOSED AS THE SOURCE OF THE FAULT AND REPLACED IN ERROR."

CLOSING FULLY OR NOT GOING FULLY DOWN WHEN OPENING. CUSTOMERS MAY REPORT A HARD CLOSE IS NOT OCCURRING UPON OPERATION CAUSE THE WINDOWS NEED TO LEARN THE END OF TRAVEL ON ALL SIDE DOOR WINDOW GLASS OPERATIONS. ONCE THE END OF THE GLASS TRAVEL HAS BEEN LEARNT THE DOOR CONTROL MODULES WILL THEN TAKE CONTROL OF THE SIDE DOOR WINDOW GLASS AND ADJUST THE SIDE GLASS STOP POSITION (UP & DOWN) TO LIMIT THE WINDOW MOVEMENT BEFORE THE END OF TRAVEL IS REACHED. THIS IS TO REDUCE THE WINDOW GLASS THUMPING THE END OF THE"

ROVER SPORT VEHICLES WHICH MAY RESULT IN THE VEHICLE ENTERING RESTRICTED PERFORMANCE MODE. CAUSE: THE ACCELERATOR PEDAL SWITCH PRINTED CIRCUIT BOARD MAY NOT HAVE BEEN CORRECTLY SOLDERED LEADING TO AN INTERMITTENT CONNECTION."

RANGE ROVER (L405) VEHICLES WHERE THE ACCELERATOR PEDAL SWITCH PRINTED CIRCUIT BOARD MAY NOT HAVE BEEN CORRECTLY SOLDERED, LEADING TO AN INTERMITTENT CONNECTION. THIS MAY RESULT IN THE VEHICLE ENTERING RESTRICTED PERFORMANCE MODE."

RANGE ROVER (L405) VEHICLES WHERE THE ACCELERATOR PEDAL SWITCH PRINTED CIRCUIT BOARD MAY NOT HAVE BEEN CORRECTLY SOLDERED, LEADING TO AN INTERMITTENT CONNECTION. THIS MAY RESULT IN THE VEHICLE ENTERING RESTRICTED PERFORMANCE MODE."

RANGE ROVER (L405) VEHICLES WHERE THE ACCELERATOR PEDAL SWITCH PRINTED CIRCUIT BOARD MAY NOT HAVE BEEN CORRECTLY SOLDERED, LEADING TO AN INTERMITTENT CONNECTION. THIS MAY RESULT IN THE VEHICLE ENTERING RESTRICTED PERFORMANCE MODE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE INSPECTION PROCEDURE DETAILED IN THIS TECHNICAL BULLETIN."

RANGE ROVER (L405) VEHICLES WHERE THE ACCELERATOR PEDAL SWITCH PRINTED CIRCUIT BOARD MAY NOT HAVE BEEN CORRECTLY SOLDERED, LEADING TO AN INTERMITTENT CONNECTION. THIS MAY RESULT IN THE VEHICLE ENTERING RESTRICTED PERFORMANCE MODE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

23% WERE FOUND TO HAVE NO DEFECTS. CAUSE: ONE POSSIBLE REASON FOR THIS IS THAT ALL HO2S SENSORS ARE REPLACED WHEN ONLY ONE IS UNSERVICEABLE"

OFF OF POWER TO THE HEADLAMPS, INSTRUMENT CLUSTER, AND TOUCH SCREEN ALL AT THE SAME TIME ACCOMPANIED BY A ""CLICKING"" NOISE SPECIFICALLY FROM THE INTERIOR FUSE BOX LOCATION BY THE GLOVE BOX. ALL SYSTEMS OPERATE NORMALLY THEREAFTER WITHOUT ANY OTHER CUSTOMER SYMPTOMS OR FAULT CODES."

CAUSE: THIS MAY BE CAUSED BY A CORRODED WIRING HARNESS AT THE FRONT AND/OR REAR BUMPER HARNESSES."

CAUSE ALTERNATORS ARE BEING DAMAGED DUE TO CROSS POLARITY WHEN THE VEHICLE IS JUMP STARTED."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD"

MODEL 2015 RANGE ROVER, SPORT. *PE

MODEL 2013-15 RANGE ROVER SPORT, RANGE ROVER. *PE

MODEL 2015 RANGE ROVER, SPORT, EVOQUE, LR4. *PE

MODEL 2015 LR4, EVOQUE, SPORT, RANGE ROVER. *PE

BOARD NOT BEING CORRECTLY SOLDERED , WHICH COULD LEAD TO INTERMITTENT CONNECTION. *LJ

is in its rearmost setting.

Locking Rear Differentials - Noisy

will jump and accelerate

drive cycle.

including roller blind type load space cover housing and PVC blind material.

drive cycle.

including roller blind type load space cover housing and PVC blind material.

drive cycle.

system using the relevant USB cable only, the device is not connecting to the vehicle.

scraping or drone noise on vehicles produced within the following vin ranges ? LG Range Rover - LG000001 to LG351464, LW Range Rover Sport ? LW100000 to LW152017, LW Range Rover Sport - LW300000 to LW399999, LW Range Rover Sport - LW500000 to LW599999, LW Range Rover Sport - LW600000 to LW687306, LR Discovery ? LR000001 to LR017639

AS A NATURAL PRODUCT AND THE CONDITIONS IT MAY CAUSE."

DISC'S WHICH ARE FITTED INTO THE BASE OF THE CUPHOLDERS HAVE BECOME DETACHED.

ON SELECTION OF THE BUTTON THE SEAT MAY STOP IN THE MID POSITION. ANY SUBSEQUENT BUTTON PRESSES WILL NOT OPERATE THE SEAT.

ON THE BUTTON THE SEAT MAY STOP IN THE MID POSITION. ANY SUBSEQUENT BUTTON PRESSES WILL NOT OPERATE THE SEAT.

CAUSE: THIS MAY BE CAUSED BY VARIOUS ISSUES."

THE SEAT IS IN ITS REARMOST SETTING.

FUNCTION, IN PARTICULAR AIR LEAKS FROM THE LUMBAR / MASSAGE FUNCTION

SELECTION OF THE AUTO HIGH BEAM (AHB) ASSIST IS GRAYED OUT ON THE INSTRUMENT CLUSTER AND CANNOT BE SELECTED FROM THE INSTRUMENT CLUSTER MENU. CAUSE: THIS MAY BE CAUSED BY AN ERROR DURING THE PROGRAMMING PROCESS IN MANUFACTURE."

CAUSE: THIS MAY BE CAUSED BY THE PROTECTIVE LACQUER NOT ADHERING TO THE SIDE STEP."

SCRAPING OR DRONE NOISE.

a door is opened/ closed.

a door is opened/ closed.

Symptoms include latches that will not lock/will not unlock/will not open.

which demonstrates the issue.

Symptoms include latches that will not lock / will not unlock / will not open.

which demonstrates the issue.

Symptoms include latches that will not lock/will not unlock/will not open.

bulging.

area.

CAUSE: PINION SEAL PREVIOUSLY NOT AVAILABLE AS A SERVICEABLE COMPONENT LEADING TO DIFFERENTIAL REPLACEMENTS."

DEFINITION OF THE PAINT FINISH (SEE ATTACHED FILE FOR AN EXAMPLE)

APPEARS REDDISH IN COLOUR WHEN COMPARED TO THE 1ST & 3RD ROW GLASS. THE ISSUE CAN ONLY BE SEEN IN CERTAIN DIRECT LIGHTING CONDITIONS. SEE ATTACHED PHOTOS FOR EXAMPLES. CAUSE: THE PIGMENT IN THE LAMINATE OF THE GLASS IS VISIBLE."

CAUSE: THIS MAY BE CAUSED BY CONTAMINATION FROM AGGREGATE-TYPE DUST AND ROAD FILM."

WHICH DEMONSTRATES THE ISSUE.

CAUSE: THIS MAY BE CAUSED BY THE VEHICLE BODY NOT BEING TO THE ORIGINAL DESIGN SPECIFICATION."

CAUSE: REPLACEMENT OF THE A-PILLAR EXTERIOR TRIM."

CAUSE: THIS MAY BE CAUSED BY A BUILD-UP OF DIRT AND GREASE ON THE SURFACE OF THE WINDSHIELD GLASS."

EACH OTHER IN THE VEHICLE AND REQUIRES THE EXTERIOR DOOR HANDLE LOCK BUTTON TO BE PRESSED. ISSUE IT HAS BEEN HIGHLIGHTED THAT IT IS POSSIBLE TO LOCK THE VEHICLE WITH BOTH KEYS INSIDE. KEYS ARE HELD TOGETHER BY CABLE TIES WHEN DELIVERED TO THE RETAILER."

REPLACED DUE TO REPORTED FLUID LEAKS. UPON FURTHER INSPECTION NO FAULTS ARE FOUND WITH THE RETURNED ROLL BARS. CAUSE: IT IS BELIEVED THAT MANY OF THE LEAKS REPORTED COULD BE COMING FROM THE PIPING, SEALS, INTERFACE OR TIGHTNESS OF BLEED SCREW."

REAR DOORS CAUSE POSSIBLE CAUSES COULD BE :- OBSTRUCTION WITHIN DOOR APERTURE OR DOOR LATCH INCORRECT DOOR STRIKER- ALIGNMENT/ADJUSTMENT DOOR FRAME SEAL COATING WORN/DAMAGED DOOR FRAME SEAL(S) WORN/DAMAGED DOOR APERTURE SEAL(S) PAINT WEAR"

CAUSE: UNDER INVESTIGATION, UPDATED SSM TO REPLACE ONLY AFFECTED PARTS."

VEHICLES (5.0L S/C V8 ONLY) FITTED WITH DYNAMIC RESPONSE MAY EXPERIENCE UNEXPECTED BODY MOVEMENTS WHEN THE VEHICLE IS STATIONARY DUE TO THE SYSTEM SELF-TEST PULSE RESULTING IN PRESSURE IN THE ACTUATORS WHICH IS NORMALLY ISOLATED FROM THEM.."

VEHICLES FITTED WITH DYNAMIC RESPONSE MAY EXPERIENCE UNEXPECTED BODY MOVEMENTS WHEN THE VEHICLE IS STATIONARY DUE TO THE SYSTEM SELF-TEST PULSE RESULTING IN PRESSURE IN THE ACTUATORS WHICH IS NORMALLY ISOLATED FROM THEM.."

CAUSE. THIS MAY BE CAUSED BY NOT POSITIONING THE ELECTRONIC TOLL TAG PROPERLY IN THE INFRARED RADIATION REFLECTIVE (IRR) LAYER CUT OUT ON THE WINDSHIELD. .

BULGING.

*PE

to respond or no functionality at all.

versions.

Examples of this may include: No infotainment audio, No audio from Park Aid, No audio from Rear Seat Entertainment, Customers with Telematics fitted may also report that internet connectivity is inoperative.

Examples of this may include: No infotainment audio, No audio from Park Aid, No audio from Rear Seat Entertainment, Customers with Telematics fitted may also report that internet connectivity is inoperative.

is not available? displayed on the instrument Cluster? due to activation failure.

from Phase 2.5 to the latest level for vehicles equipped with Rear Seat Entertainment. This concern can leave the ISC in a non-communicative state.

Bluetooth the user may experience a connectivity issues.

inoperative

.The concern occurs when updating to phase 4.0 using PATHFINDER 180

Bluetooth the user may experience a connectivity issues.

can no longer provide Navigation destination entry via voice control.

inoperative

.The concern occurs when updating to phase 4.0 using PATHFINDER 180

from Phase 2.5 to the latest level for vehicles equipped with Rear Seat Entertainment. This concern can leave the ISC in a non-communicative state.

Bluetooth the user may experience a connectivity issues.

Bluetooth the user may experience a connectivity issues.

can no longer provide Navigation destination entry via voice control.

from Phase 2.5 to the latest level for vehicles equipped with Rear Seat Entertainment. This concern can leave the ISC in a non-communicative state.

Bluetooth the user may experience a connectivity issues.

left or right tune soft key buttons or when selecting an alternative radio band (ie trying to change from FM to DAB) there is no response from touch screen and audio output remains distorted. The DTC B14D3-96 may also be stored in the Infotainment Master Controller (IMC) suggesting a radio tuner component internal failure.

The Audio/Video button on touch-screen home page may also be greyed out.

the InControl Touch Pro system, or cause system functionality concerns after the infotainment system was successfully updated.

the InControl Touch Pro system, or cause system functionality concerns after the infotainment system was successfully updated.

the InControl Touch Pro system, or cause system functionality concerns after the infotainment system was successfully updated.

longer process voice inputs or outputs. Common symptoms are reported as: Voice commands are not recognized. Voice output such as spoken navigation guidance is inoperative.

to respond or no functionality at all.

designed.

During a semi-automated park assist manoeuver, the system may be cancelled half way through due to an object being detected within 30 cm of the side of the vehicle. The system will then output a continuous tone and the message 'Park Assist Cancelled' will be displayed on the Instrument Cluster.

TIME TO SERVICE IS BELOW THE 16,000 MILES (26,000 KM) OR 12 MONTH SERVICE INTERVAL.

IN ADDITION THE CURRENT VEHICLE LOCATION INDICATOR WILL NOT LOCK ONTO THE CORRECT LOCATION ON THE MAP. CAUSE: SOFTWARE ERROR."

DURING A SEMI-AUTOMATED PARK ASSIST MANOEUVER, THE SYSTEM MAY BE CANCELLED HALF WAY THROUGH DUE TO AN OBJECT BEING DETECTED WITHIN 30 CM OF THE SIDE OF THE VEHICLE. THE SYSTEM WILL THEN OUTPUT A CONTINUOUS TONE AND THE MESSAGE 'PARK ASSIST CANCELLED' WILL BE DISPLAYED ON THE INSTRUMENT CLUSTER. CAUSE: THIS MAY BE CAUSED BY A SOFTWARE ERROR."

WHEN THE TERRAIN RESPONSE CONTROL IS SET TO AUTO MODE. ON OCCASIONS THE WHEEL POSITION SHOWN IN THE MESSAGE CENTRE APPEARS TO REMAIN IN A CONSTANT POSITION THAT DOES NOT MATCH THE ROAD WHEEL POSITION. THE DISPLAY WILL RETURN TO NORMAL WHEN THE VEHICLE IS STATIONARY. PLEASE VIEW THE ATTACHMENT THAT SHOWS THE MESSAGE CENTRE DISPLAY. CAUSE: SOFTWARE CALCULATION. LOW LINE INSTRUMENT CLUSTER AFFECTED ONLY."

WHERE THE TOUCH SCREEN MAY GO 'BLACK' FOR 10 SECONDS FOLLOWED BY DISPLAYING THE 'LAND ROVER' LOGO BEFORE RETURNING TO NORMAL DISPLAY OPERATION."

WHERE THE TOUCH SCREEN MAY GO 'BLACK' FOR 10 SECONDS FOLLOWED BY DISPLAYING THE 'LAND ROVER' LOGO BEFORE RETURNING TO NORMAL DISPLAY OPERATION. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

IN THE INSTRUMENT CLUSTER MESSAGE CENTER WHEN THE TERRAIN RESPONSE SWITCHPACK IS SET TO AUTO MODE. THE WHEEL POSITION SHOWN IN THE MESSAGE CENTER MAY APPEAR TO REMAIN IN A CONSTANT POSITION THAT DOES NOT MATCH THE POSITION OF THE ROAD WHEEL. THE MESSAGE CENTER DISPLAY WILL RETURN TO NORMAL WHEN THE VEHICLE IS STATIONARY.

CAUSE THERE IS A POTENTIAL THAT THE TOP WINDSCREEN SEAL HAS BECOME DISLODGED OVER TIME CAUSING A WINDNOISE"

DIAGNOSTIC TROUBLE CODES (DTC) ARE STORED. CAUSE: THIS MAY BE CAUSED BY VARIOUS ISSUES."

WHICH IS NOT COMPATIBLE WITH LAND ROVER INFOTAINMENT SYSTEMS. CAUSE THIS IS TO MAKE YOU AWARE OF THE TYPES OF MEDIA THAT MAY CAUSE THE UNIT TO FAIL WITH THE CUSTOMER."

WHICH IS NOT COMPATIBLE WITH LAND ROVER INFOTAINMENT SYSTEMS. CAUSE THIS IS TO MAKE YOU AWARE OF THE TYPES OF MEDIA THAT MAY CAUSE THE UNIT TO FAIL WITH THE CUSTOMER. THEY ARE COPY CONTROL COMPACT DISCS (CCCD) RECORDABLE COMPACT DISCS (CD-R) REWRITABLE COMPACT DISCS (CD-RW) ECO DISCS, WHICH ARE VERY THIN, ONLY 0.6MM. PLEASE REFER TO ATTACHMENT FOR EXAMPLES OF DISCS THAT ARE KNOWN TO HAVE CAUSED DAMAGE."

PLAYBACK.

Sport (L494) and Range Rover (L405) vehicles where the Touch Screen may go 'black' for 10 seconds followed by displaying the 'Land Rover' logo before returning to normal display operation.

instrument cluster.

and/or has a poor finish.

The EPB applied light is not on. The ABS (Anti-lock braking system), DSC (Dynamic stability Control) and brake warning lights are on. The "Autonomous Emergency Braking not available" message is displayed.

heard from the front brakes during low-speed driving forward/backward, the 'squeal' can be heard also during moderate brake pedal application at low speeds, until the vehicle comes to a stop. The 'squeal' noise may resonate at frequencies of around 7kHz and 8kHZ.

housing.

and/or has a poor finish.

the following DTC stored within the Anti-Lock Braking System (ABS) module. U0001-82 High Speed CAN Communication Bus - Alive/sequence counter incorrect / not updated

vehicle speeds.

and/or has a poor finish.

the following DTC stored within the Anti-Lock Braking System (ABS) module. U0001-82 High Speed CAN Communication Bus - Alive/sequence counter incorrect / not updated

speeds.

heard from the front brakes during low-speed, light-to-moderate brake pedal application, until the vehicle comes to a stop.

EPQR & TA data provided by retailers to date, shows a varied range of conditions (environmental, drive cycle and road type) that may initiate the known noises. Although the noises do not, in most cases, indicate a degradation in functionality or braking performance, they may lead to customer dissatisfaction and unscheduled retailer visits for repair action. Note: Off road use of the vehicle is not categorised in the communication due to the extended range of parameters and conditions that the vehicle operate at. Defining and describing brake noises is proven to be difficult through our different languages and terminology. In the ?Solutions? section below, there are noise descriptions and Technical Service Bulletins references to aid the repair selection. See ?Action? for further guidance.

EPQR & TA data provided by retailers to date, shows a varied range of conditions (environmental, drive cycle and road type) that may initiate the known noises. Although the noises do not, in most cases, indicate a degradation in functionality or braking performance, they may lead to customer dissatisfaction and unscheduled retailer visits for repair action. Note: Off road use of the vehicle is not categorised in the communication due to the extended range of parameters and conditions that the vehicle operate at. Defining and describing brake noises is proven to be difficult through our different languages and terminology. In the ?Solutions? section below, there are noise descriptions and Technical Service Bulletins references to aid the repair selection. See ?Action? for further guidance.

and/or has a poor finish.

noise may be heard from the front brakes during low-speed, light-to-moderate brake pedal application, until the vehicle comes to a stop.

the following DTC stored within the Anti-Lock Braking System (ABS) module. U0001-82 High Speed CAN Communication Bus - Alive/sequence counter incorrect / not updated.

may be heard from the front brakes during low-speed, light-to-moderate brake pedal application, until the vehicle comes to a stop.

NOISE MAY BE HEARD FROM THE FRONT BRAKES DURING LOW-SPEED, LIGHT-TO-MODERATE BRAKE PEDAL APPLICATION, UNTIL THE VEHICLE COMES TO A STOP."

CAUSE: CURRENTLY UNDER ANALYSIS."

POOR FINISH.

POOR FINISH.

CAUSE BRAKE LIGHT SWITCH / BRAKE PEDAL SHIM INTERACTION. NOTE: NOT ALL VEHICLES WILL BE FITTED WITH BRAKE PEDAL SHIM."

CAUSE: DAMAGE TO THE CALIPER FINISH WHILE CLEANING THE VEHICLE AND, OR THE ROAD WHEELS"

NOISE MAY BE HEARD FROM THE FRONT BRAKES DURING LOW-SPEED, LIGHT-TO-MODERATE BRAKE PEDAL APPLICATION, UNTIL THE VEHICLE COMES TO A STOP. CAUSE: THIS MAY BE CAUSED BY FRONT BRAKE PAD RESONANCE."

CAUSE: A LACK OF GREASING DURING PAD REPLACEMENT OR BRAKE USAGE CHARACTERISTIC."

CAUSE: THIS MAY BE CAUSED BY ICE BUILD UP BETWEEN THE FOAM SURFACES AND THE HOOD CAUSING PENETRATION INTO THE FOAM."

ISSUE SQUEAK NOISE WHEN BRAKE PEDAL IS OPERATED. CAUSE BRAKE LIGHT SWITCH / BRAKE PEDAL SHIM INTERACTION. NOTE: NOT ALL VEHICLES WILL BE FITTED WITH BRAKE PEDAL SHIM."

USUALLY THIS WILL OCCUR AT LOW SPEEDS. THIS VERSION HAS BEEN ISSUED TO ADD MENA TO THE MARKETS. CAUSE: THE SHAPE OF THE BRAKE PAD MEANS THAT UNDER CERTAIN BRAKING CONDITIONS IT WILL RESONATE CAUSING A SQUEAL NOISE. SUGGESTED CUSTOMER CONCERN CODE GB5."

ISSUE: DIAGNOSTIC TROUBLE CODES (DTCS) STORED IN THE ANTI-LOCK BRAKING SYSTEM (ABS) MODULE RELATING TO AN ERROR STATE WITH A WHEEL SPEED SENSOR ONLY. CAUSE: CURRENTLY UNDER ANALYSIS."

VEHICLES FITTED WITH HIGH PERFORMANCE/BREMBO BRAKES, POST 10 MODEL YEAR ONLY. RANGE ROVER SPORT AA215623 TO CA738069. RANGE ROVER AA302697 TO CA373799. VEHICLES AFTER THE END VIN NUMBERS QUOTED ABOVE WILL HAVE THE NEW PINS FITTED AS STANDARD. CAUSE: GALVANIC CORROSION OF THE RETAINING PINS. THE PINS NOW HAVE A NEW PLATING WHICH IS MORE RESISTANT TO CORROSION."

CAUSE BRAKE LIGHT SWITCH / BRAKE PEDAL SHIM INTERACTION. NOTE: NOT ALL VEHICLES WILL BE FITTED WITH BRAKE PEDAL SHIM."

RANGE ROVER, RANGE ROVER SPORT AND DISCOVERY 4/LR4. 14 AND 15 MODEL YEAR ONLY. CAUSE: CURRENTLY UNDER INVESTIGATION"

MAY BE HEARD FROM THE REAR BRAKES DURING LIGHT BRAKING.

The noise is most prominent while accelerating/decelerating and when turning the steering wheel, such as when performing a U-turn and applying the throttle.

The noise is most prominent while accelerating/decelerating and when turning the steering wheel, such as when performing a U-turn and applying the throttle.

The 'clonk' will be most prominent while accelerating/decelerating and when turning the steering wheel. The noise may be more noticeable when performing a U-turn and applying the throttle.

situations.

steering at low vehicle speeds, such as turning left or right at an intersection.

BY VISUAL OR AUDIBLE WARNINGS THROUGH THE INSTRUMENT PACK.

STEERING AT LOW VEHICLE SPEEDS, SUCH AS TURNING LEFT OR RIGHT AT AN INTERSECTION.

BE FOUND WITHIN THE POWER STEERING FLUID SYSTEM WHICH COULD LEAD TO SYSTEM CONTAMINATION AND A DETERIORATION IN SYSTEM PERFORMANCE. CAUSE: INTERNAL DEBRIS FROM A SUSPECTED COMPONENT MALFUNCTION MAY RESULT IN THE POWER STEERING FLUID BECOMING CONTAMINATED."

CAUSE: UNDER INVESTIGATION"

CAUSE: UNDER INVESTIGATION"

ISSUE: A CUSTOMER MAY COMPLAIN OF A SQUEAK OR CREAK FROM THE STEERING COLUMN AREA ON ROTATION OF THE STEERING WHEEL. RANGE ROVER SPORT L320 ONLY. CAUSE: THE POWER STEERING PINION SEAL LACKS LUBRICATION AND DRIES OUT."

RANGE ROVER SPORT L320 ONLY. CAUSE: THE POWER STEERING PINION SEAL LACKS LUBRICATION AND DRIES OUT."

THE ISSUE IS COMMON ACROSS ALL MANUFACTURERS SYMPTOMS WHEN THE APPLE DEVICE IS CONNECTED TO THE CAR SYSTEM AND A CALL IS RECEIVED THERE IS NO OPTION TO ANSWER OR REJECT THE INCOMING CALL ON THE SYSTEM. THE STEERING WHEEL CONTROLS ALSO HAVE NO EFFECT. THE TOUCH SCREEN CONTINUES TO DISPLAY THE PHONE SCREEN. THE POP-UP SCREEN TO ANSWER OR REJECT THE CALL IS NOT SHOWN."

Fault codes U210A - 16 and C1A24 - 67 may also be stored.

On investigation the front Air Spring is found to be misaligned and damaged.

Upon further investigation, Diagnostic Trouble Code (DTC) C1A13-64 may be stored.

Upon further investigation, Diagnostic Trouble Code (DTC) C1A13-54 may be stored.

Vehicle Range which may experience an amber or red warning symbol and associated text in the Instrument Cluster.- Amber symbol - no change to vehicle or suspension performance but suspension unable to lower on demand with warning message 'Suspension fault' displayed. - Red symbol - vehicle height is above nominal standard ride height and unable to lower on demand with warning message 'Do not exceed 30 MPH' displayed.

may experience an amber or red warning symbol and associated text in the Instrument Cluster. ? Amber symbol - no change to vehicle or suspension performance, but suspension unable to lower on demand; warning message 'Suspension fault' displayed. ? Red symbol - vehicle height is above nominal standard ride height and unable to lower on demand; warning message 'Do not exceed 30 MPH' displayed.

manufactured away from process and, in some cases, a general warning/information message (red or amber) for the air suspension system. This could occur in normal driving when the air suspension system attempts to vent air or when the vehicle attempts to lower itself, either by the driver demand or automatic access.

may have been manufactured away from process and, in some cases, a general warning/information message (red or amber) for the air suspension system will display. This could occur in normal driving when the air suspension system attempts to vent air or when the vehicle attempts to lower itself, either by the driver demand or automatic access.

INSTRUMENT PACK EVEN THOUGH THE HOOD / BONNET IS CLOSED CAUSE: THERE IS A POTENTIAL THAT AN INTERNAL SPRING COULD BECOME DISLODGED"

CAUSE: THIS MAY BE CAUSED BY METAL-TO-METAL CONTACT BETWEEN THE SEAT SUSPENSION MAT HOOKS AND THE SEAT FRAME AND MAY BE VERIFIED BY VISUAL INSPECTION OF SEAT SUPPORT MAT LOCATION HOLE WEAR."

DIAGNOSTIC TROUBLE CODE (DTC) C1A13-64 MAY BE STORED.

REPORT A NOISE OR A VEHICLE LEAN ERROR STATE. ON INVESTIGATION THE FRONT AIR SPRING IS FOUND TO BE MISALIGNED AND DAMAGED. SEE ATTACHED PHOTO CAUSE(S): INFLATION OF AIR SUSPENSION AIR SPRINGS WITH THE VEHICLE ON THE GROUND (NOT ON A WHEEL FREE LIFT) CAN CAUSE MISALIGNMENT AND CREASING OF THE AIR BAG. THE INFLATION PRESSURES ACTING ON THE CREASED AIR BAG CAN CAUSE PERMANENT DAMAGE."

CAUSE: AIR LEAK FROM A FRONT OR REAR AIR SPRING TO DAMPER LOWER SEAL."

ACTION: IN ORDER TO CORRECTLY DIAGNOSE THE LEAK PATH ON A STABILIZER BAR, CLEAN THE SUSPECTED AREA THOROUGHLY AND CONFIRM IF THE LEAK IS FROM THE PIPE O-RINGS, THE STABILIZER BAR HYDRAULIC SEAL OR SOMEWHERE ELSE. IF FOUND TO BE FROM THE PIPE O-RINGS (SEE ATTACHED DOCUMENT), THESE ARE SERVICEABLE PARTS AND SHOULD BE REPLACED. IF THE LEAK IS FOUND TO BE FROM THE HYDRAULIC SEAL, THIS IS NOT A SERVICEABLE PART AND A NEW STABILIZER BAR WILL BE REQUIRED."

MAY EXPERIENCE AN AMBER OR RED WARNING SYMBOL AND ASSOCIATED TEXT IN THE INSTRUMENT CLUSTER. AMBER SYMBOL - NO CHANGE TO VEHICLE OR SUSPENSION PERFORMANCE BUT SUSPENSION UNABLE TO LOWER ON DEMAND WITH WARNING MESSAGE 'SUSPENSION FAULT' DISPLAYED. RED SYMBOL - VEHICLE HEIGHT IS ABOVE NOMINAL STANDARD RIDE HEIGHT AND UNABLE TO LOWER ON DEMAND WITH WARNING MESSAGE 'DO NOT EXCEED 30 MPH' DISPLAYED."

DIAGNOSTIC TROUBLE CODE (DTC) C1A13-64 MAY BE STORED.

MAY EXPERIENCE AN AMBER OR RED WARNING SYMBOL AND ASSOCIATED TEXT IN THE INSTRUMENT CLUSTER. AMBER SYMBOL - NO CHANGE TO VEHICLE OR SUSPENSION PERFORMANCE, BUT SUSPENSION UNABLE TO LOWER ON DEMAND; WARNING MESSAGE 'SUSPENSION FAULT' DISPLAYED. RED SYMBOL - VEHICLE HEIGHT IS ABOVE NOMINAL STANDARD RIDE HEIGHT AND UNABLE TO LOWER ON DEMAND; WARNING MESSAGE 'DO NOT EXCEED 30 MPH' DISPLAYED."

CONTROL ARM TO KNUCKLE BOLT(S) HAS FAILED, IN CERTAIN VEHICLES. NO MODEL OR YEARS LISTED. *PE

The customer may experience one of the following symptoms: ? The release button appears loose or has no resistance when operated. ? The release button appears to be binding or will not move when operated.

The button on the shifter does not work.

is pressed and the selector operated with one or more of the following symptoms noted on a Range Rover Sport 2014-2016 MY only: Release button appears loose or no resistance when pressed, Release button appears to be binding or will not move when pressed.

exhibit intermittent operation, causing one or more of the following issues: ? Audio volume does not adjust (up and/or down)? Radio 'seek' buttons do not operate ? Volume control buttons cause the radio station to change ? InControl system slow to operate (blank screen followed by the 'Land Rover' logo) ? Transmission paddle shifters do not operate ? Diagnostic Trouble Codes (DTC) U2013-02 and/or B1D21-13 stored

UPON INSPECTION, LOW PRESSURE IS RECORDED ON THE HIGH PRESSURE SYSTEM, HIGH PRESSURE IS RECORDED ON THE LOW PRESSURE SYSTEM, AND THE COMPRESSOR CLUTCH (WHERE APPLICABLE) IS WORKING PROPERLY.

INSTRUMENT PACK WITH ASSOCIATED DTC'S FOR BRAKE LIGHT SWITCH (P0504-27, P0504-62, C1A96-64) OR BRAKES SHOWING SIGNS OF DRAG AND BINDING. CAUSE: INCORRECT BRAKE LIGHT SWITCH SETTING. NOTE: ANALYSIS OF RETURNED BRAKE SWITCHES HAVE SHOWN NO ISSUES WITH THE BRAKE SWITCH ITSELF. DO NOT REPLACE THE SWITCH BEFORE ADJUSTMENT IS CARRIED OUT."

PLEASE VIEW ATTACHMENT THAT SHOWS THE CONDITION. CAUSE: PAINT SURFACE FINISH PROCESS"

PADDLES OR THE GEAR SELECTOR [RANGE ROVER SPORT ONLY]) AND DOES NOT REVERT BACK TO AUTO MODE. CAUSE: THIS MAY BE CAUSED BY AN INCORRECT CALIBRATION CAUSING THE VEHICLE TO ENTER MANUAL ONLY MODE WHEN THE 'PROGRESS CONTROL SYSTEM' SELECTS A MODE OF OPERATION."

CRUISE CONTROL) AND TRANSMISSION PADDLE SWITCHES MAY EXHIBIT INTERMITTENT OPERATION, CAUSING ONE OR MORE (LIST NOT EXHAUSTIVE) OF THE FOLLOWING ISSUES: AUDIO VOLUME WILL NOT ADJUST (UP AND/OR DOWN) RADIO SEEK BUTTONS WILL NOT OPERATE VOLUME CONTROL BUTTONS CAUSE THE RADIO STATION TO CHANGE THE INFOTAINMENT SYSTEM IS SLOW TO OPERATE (BLANK SCREEN FOLLOWED BY THE 'LAND ROVER' LOGO) DIAGNOSTIC TROUBLE CODE (DTC) U2013-02 'SWITCH PACK, GENERAL SIGNAL FAILURE' IS STORED IN THE INSTRUMENT CLUSTER MEMORY DTC B1D21-13 'REMOTE CONTROL SWITCH CIRCUIT OPEN' IS STORED IN THE TOUCH SCREEN MEMORY TRANSMISSION PADDLE SWITCHES INOPERATIVE OR INTERMITTENT FUNCTIONALITY CRUISE CONTROL INOPERATIVE"

ONLY) AND RANGE ROVER (L405; 3.0L SC V6 ONLY) VEHICLES WHERE A FLASHING 'D' IS DISPLAYED IN THE TRANSMISSION CONTROL SWITCH (TCS) AFTER AN ECO STOP/START EVENT AND/OR A 'GEARBOX FAULT' MESSAGE IS DISPLAYED IN THE INSTRUMENT CLUSTER, THE VEHICLE HAS DEFAULTED TO LIMP HOME MODE, AND DIAGNOSTIC TROUBLE CODES (DTC) P2702-07 AND P07DD-07 ARE STORED IN THE TRANSMISSION CONTROL MODULE (TCM)."

ONLY) AND RANGE ROVER (L405; 3.0L SC V6 ONLY) VEHICLES WHERE A FLASHING 'D' IS DISPLAYED IN THE TRANSMISSION CONTROL SWITCH (TCS) AFTER AN ECO STOP/START EVENT AND/OR A 'GEARBOX FAULT' MESSAGE IS DISPLAYED IN THE INSTRUMENT CLUSTER, THE VEHICLE HAS DEFAULTED TO LIMP HOME MODE, AND DIAGNOSTIC TROUBLE CODES (DTC) P2702-07 AND P07DD-07 ARE STORED IN THE TRANSMISSION CONTROL MODULE (TCM). ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

THERE MAY BE NO FAULT CODES OR WARNING LIGHTS PRESENT. CAUSE: SIDE IMPACT TO THE VEHICLE WHEELS."

CAUSE: THIS MAY BE CAUSED BY A CRACKED TRANSMISSION HEAT SHIELD MOUNTING BRACKET."

CAUSE: PAINT SURFACE FINISH NOT AS EXPECTED."

THERE MAY BE NO FAULT CODES OR WARNING LIGHTS PRESENT. CAUSE: SIDE IMPACT TO THE VEHICLE WHEELS."

be damaged.

(blowing warm and then cold); ? Windshield, rear window, and/or door windows mist up in cool (15C or lower) ambient temperatures; ? Poor cooling performance of the Air Conditioning (A/C) system; and/or ? Warm, damp or musty smells coming from the vents.

system is in operation and low temperature selected.

OR REAR CLIMATE FANS ARE ON A HIGH SETTING. ALSO, AN INTERMITTENT TAPPING/ RATTLE MAYBE HEARD.

WHEN SELECTED.

CAUSE: THIS MAY BE CAUSED BY PARAMETERS WITHIN THE CLIMATE CONTROL SYSTEM NOT OPERATING EFFICIENTLY."

CAUSE: THIS MAY BE CAUSED BY PARAMETERS WITHIN THE CLIMATE CONTROL SYSTEM NOT OPERATING EFFICIENTLY."

This applies to both high line and low line rear camera.

Driven Diagnostics (SDD) does not appear to communicate with the RFA: FK72-19H440-AE, FK72-19H440-BE, FK72-19H440-AF, FK72-19H440-BF, Following models only affected: L538 Range Rover Evoque 14MY onwards, L550 Discovery Sport 15MY onwards, L494 Range Rover Sport 14MY onwards, L405 Range Rover 14MY onwards

This can cause the alarm to trigger or the vehicle to not lock.

When interrogated with diagnostic equipment the following fault codes may be present: C1A20-64, C1131-92

Instead, the vehicle will start to lower, and then rise to off-road / raised height with a warning light on the instrument pack. This occurs when the vehicle lowers much more slowly than expected.

Instead, the vehicle will start to lower, and then rise to off-road / raised height with a warning light on the instrument pack. This occurs when the vehicle lowers much more slowly than expected.

Instead, the vehicle will start to lower, and then rise to off-road / raised height with a warning light on the instrument pack. This occurs when the vehicle lowers much more slowly than expected.

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES"

CAUSE: DAMAGE/MARKING CAUSED BY OBJECT IMPACT AGAINST THE LENS. STAINING/DISCOLORATION CONTAMINATION CAUSED BY USING ANY TYPE OF CLEANING PRODUCT ON LENS. IMPORTANT: OWNERS HANDBOOK SPECIFIES TO CLEAN WITH A LIGHTLY MOISTENED CLOTH AND DO NOT USE CHEMICAL AGENTS OR DOMESTIC CLEANERS ACTION WHERE A CUSTOMER CONCERN IS REPORTED, PLEASE ORDER THE LENS KIT FOR THE RELEVANT MODEL"

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OUTSIDE OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE PERFORMANCE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES."

displaying less fuel than what is actually in the fuel tank [gauge reading when the fuel tank is full]).

displaying less fuel than what is actually in the fuel tank [gauge reading when the fuel tank is full]).

DISPLAYING LESS FUEL THAN WHAT IS ACTUALLY IN THE FUEL TANK [GAUGE READING WHEN THE FUEL TANK IS FULL])."

A NUMBER OF POSSIBLE CAUSES FOR FUEL FILLING DIFFICULTIES. PLEASE REFER TO TOPIX WORKSHOP MANUAL SECTION '303-13: EVAPORATIVE EMISSIONS, DIAGNOSIS AND TESTING' IN THE FIRST INSTANCE FOR ADVICE ON SYSTEM CHECKS."

We require all retailers to follow the procedure outlined below ahead of conducting wheel alignment warranty work on Evoque (L538), Discovery Sport (L550), RR (L405), RRS (L494), Discovery (L462), and Velar (L560).

CAUSE: THIS IS EITHER CAUSED BY THE SHIPPING PROCESS AND SHOULD BE CLAIMED THROUGH TRANSPORT / DISTRIBUTION OR IT IS CAUSED DURING JLR MANUFACTURING PROCESSES AND SHOULD BE CLAIMED AS PER WARRANTY POLICY."

SPORT (L494), AND RANGE ROVER (L405) VEHICLES WHICH MAY BE FITTED WITH WHEEL NUTS THAT DO NOT MEET THE REQUIRED SPECIFICATION."

CAUSE: WHEEL AND TYRE ASSEMBLIES OUT OF BALANCE DUE TO WATER INSIDE THE WHEEL AND TYRE ASSEMBLIES. SEE ATTACHMENT FOR EXAMPLE."

CAUSE. WITH REFERENCE TO THE PHOTO ATTACHED, DUE TO THE TREAD PATTERN DESIGN OF THIS TYRE, THERE CAN APPEAR TO BE INNER OR OUTER SHOULDER WEAR. THIS IS IN FACT JUST THE NATURAL TREAD WEAR, BUT AS THE DESIGN OF THE LATERAL GROOVES CONTINUES AROUND TO THE SIDEWALL, THE VERY ENDS OF THE GROOVES DO NOT WEAR GIVING RISE TO A ""BAND"" OF WEAR AT THE EDGE OF THE CONTACT PATCH."

Please refer to the following publications on TOPIx for the latest details. Land Rover SSM #73635

Upon further inspection no faults are found with the returned roll bars.

Upon further inspection no faults are found with the returned roll bars.

Upon further inspection no faults are found with the returned roll bars.

Upon further inspection no faults are found with the returned roll bars.

be ?No Fault Found? during part return analysis.

point.

(IC) FOR LESS THAN ONE SECOND WHEN NO SERVICE IS REQUIRED.

(SEE FIG.1) ACTION: REPLACE BY PRESSING ON NEW BUTTON CAP PART NO: LR045801 (SEE FIG.2)"

This is only a temporary position and will be included in a future update to the publications on TOPIx.

with InControl Touch Pro to latest software version NGI 17C on both Symptom Driven Diagnostics (SDD) and PATHFINDER. Additional vehicle feedback data shows that the failure rate is increasing, despite the many improvements made in Pathfinder 123 and SDD 152.00. JLR recommend that no further vehicles are routinely updated to NGI 17C. (Note below reference urgent vehicles only.)

CONTROLLER (ISC, FOR REAR SEAT ENTERTAINMENT ) THE SYSTEM MAY EXHIBIT THE FOLLOWING CONDITIONS DUE TO INCOMPLETE VARIANT CONFIGURATION LEARN PROCEDURE DURING THE SOFTWARE UPDATE."

CAUSE: THIS MAY BE CAUSED BY A SOFTWARE ISSUE WITH THE REMOTE FUNCTION ACTUATOR (RFA)."

TRANSLATED AND DISPLAYED AS 'AIRBAG FAULT'.

TRANSLATED AND DISPLAYED AS 'AIRBAG FAULT'. CAUSE: THIS MAY BE CAUSED BY A SOFTWARE ERROR IN THE INSTRUMENT CLUSTER."

TRANSLATED AND DISPLAYED AS 'AIRBAG FAULT'. CAUSE: THIS MAY BE CAUSED BY A SOFTWARE ERROR IN THE INSTRUMENT CLUSTER."