2015 Land Rover Range Rover Evoque TSBs

removal, leaving it loose when refitted and likely to become adrift (see attachment).

of the vehicle.

frequency ?squeak? or ?squeal? noise from the front or rear of their vehicles, observed most noticeably whilst driving over speed bumps or uneven road surfaces. Technicians have resolved the complaints by replacing front or rear anti-roll bar (ARB) bushes. Investigations into returned components by both JLR and component suppliers have not been able to identify causal factors for the original complaint.

There is a judder feeling when turning.

Range where water ingress into the passenger compartment or wind noise may be evident.

ingress into the passenger compartment or wind noise may be evident.

into the passenger compartment or wind noise may be evident

during cold ambient temperatures.

a drive cycle.

vents, affecting the ability to set a constant, comfortable temperature in the passenger compartment.

including roller blind type load space cover housing and PVC blind material.

compartment on delivery of a new vehicle.

inoperative or sticking (please see attached picture).

vents, affecting the ability to set a constant, comfortable temperature in the passenger compartment.

including roller blind type load space cover housing and PVC blind material.

compartment on delivery of a new vehicle.

inoperative or sticking (please see attached picture).

system using the relevant USB cable only, the device is not connecting to the vehicle.

AS A NATURAL PRODUCT AND THE CONDITIONS IT MAY CAUSE."

CAUSE: MORE INFORMATION IS REQUIRED TO BETTER UNDERSTAND THE ISSUE TO SUPPORT INVESTIGATION AND RECTIFICATION."

CAUSE THE CLEAR LACQUER COATING ON THE GRILLE NOT CORRECT TO MANUFACTURING STANDARD. "

CAUSE THE CLEAR LACQUER COATING ON THE GRILLE NOT CORRECT TO MANUFACTURING STANDARD."

CAUSE: 15 MY CCF FILES ARE IN A DIFFERENT FORMAT AND ARE NOT RECOGNISED BY SDD"

ECKO stop

has been observed with associated Tyre Pressure Monitoring System (TKPMS) warning messages. Customers and retailers have been unable to re-

There is a hesitation. The Check Engine MIL goes on and off. There is a noise on startup.

The engine will shut off intermittently and restart immediately with a key cycle.

The Check Engine Light is on, there is noise from the engine.

The Check Engine Light is on, there is noise from the engine.

A Restricted Performance message may also be reported.

A Restricted Performance message may also be reported.

DTC P242B-64 logged in Powertrain Control Module (PCM).Issue applies to AJ20-D4 engine only.

DTC P242B-64 logged in Powertrain Control Module (PCM).Issue applies to AJ20-D4 engine only.

DTC P242B-64 logged in Powertrain Control Module (PCM).Issue applies to AJ20-D4 engine only.

The Check Engine Light is on, there is noise from the engine.

Diagnostic Trouble Code (DTC) B1B87-31, stored in Driver Seat Module (DSM) or Passenger Seat Module (PSM) Note that the seat height motor is supplied as part of the cushion sub-assembly or motor sub-assembly (depending on model)

The Check Engine Light is on, there is noise from the engine.

Diagnostic Trouble Code (DTC) B1B87-31, stored in Driver Seat Module (DSM) or Passenger Seat Module (PSM) Note that the seat height motor is supplied as part of the cushion sub-assembly or motor sub-assembly (depending on model)

Range where in some circumstances the secondary catalyst fueling adaption may be incorrect. This will illuminate the engine Malfunction Indicator Lamp (MIL) with Diagnostic Trouble Code (DTC) P2096 or P2097 stored in the Powertrain Control Module PCM).

some circumstances the secondary catalyst fueling adaption may be incorrect. This will illuminate the engine MIL (Malfunction Indicator Lamp) with DTC (Diagnostic Trouble Code) P2096 or P2097 stored in the Powertrain Control Module PCM).

Upon further investigation oil is found to be leaking from the interface of the PTU and the automatic transmission.

exhibits poor starting; and/or ? Engine MIL (Malfunction Indicator Lamp) illuminated with DTC (Diagnostic Trouble Code) P0300, P0301, P0302, P0303, P0304, and/or P1315 stored in the Powertrain Control Module (PCM).

poor starting; and/or ? Engine MIL (Malfunction Indicator Lamp) illuminated with DTC (Diagnostic Trouble Code) P0300, P0301, P0302, P0303, P0304, and/or P1315 stored in the Powertrain Control Module (PCM).

poor starting; and/or ? Engine MIL (Malfunction Indicator Lamp) illuminated with DTC (Diagnostic Trouble Code) P0300, P0301, P0302, P0303, P0304, and/or P1315 stored in the Powertrain Control Module (PCM).

Diagnostic Trouble Code (DTC) P0016, P0017, P0026, or P0341 may be stored in the Powertrain Control Module (PCM).

Transmission internal differential right output half shaft.

poor starting; and/or ? Engine Malfunction Indicator Lamp (MIL) illuminated with Diagnostic Trouble Codes (DTC) P0300, P0301, P0302, P0303, P0304, and/or P1315 stored in the Powertrain Control Module (PCM).

running poorly or exhibiting instability. Upon further diagnosis, the Technician may find Diagnostic Trouble Code (DTC) P2282-00 stored in the Powertrain Control Module (PCM).

MANY ARE DEEMED AS NO FAULT FOUND. IT IS POSSIBLE DURING AN ECO STOP START THAT THE VEHICLE DOES NOT RE-START. CAUSE INCORRECT DIAGNOSIS."

CAUSE ALTERNATOR REGULATOR FAULTY IN ALTERNATOR PART NUMBER LR028121."

'TRANSMISSION FAULT' MESSAGE IN THE INSTRUMENT CLUSTER (IC) COMBINED WITH A FAILURE TO ENGAGE A GEAR RESULTING IN LOSS OF ACCELERATION.

DISPLAYED IN THE INSTRUMENT CLUSTER; ENGINE FAILS TO CRANK; VEHICLE MAY NOT UNLOCK / LOCK WHEN USING PASSIVE ENTRY OR WHEN PRESSING A SMART KEY BUTTON.

ILLUMINATED IN THE INSTRUMENT CLUSTER & DTC P2096-00 AND/OR P2097-00 IS EVIDENT IN THE PCM. A CONCERN IN THE PCM DIAGNOSTIC SOFTWARE HAS BEEN DISCOVERED, WHICH WHEN COMBINED WITH A SPECIFIC CUSTOMER DRIVE CYCLE CAN LEAD TO THE FALSE FLAGGING OF THIS DTC. WORK IS ON-GOING TO DELIVER REVISED PCM SOFTWARE; TIMING IS TO BE CONFIRMED. EXHAUST SYSTEM LEAKS OUTSIDE DESIGN SPECIFICATION CAN INCREASE THE LIKELIHOOD OF REPEAT FAILURES. JLR HAVE RECOGNISED THAT THE SUPPLIED LEAK CHECK EQUIPMENT DOES NOT FIT ON CERTAIN LC - DISCOVERY SPORT EXHAUST TAIL PIPES. A SOLUTION IS BEING SOURCED."

ILLUMINATED IN THE INSTRUMENT CLUSTER & P2096-00 AND OR P2097- 00 IS EVIDENT IN THE PCM. ACTION: AS PER THE 'POSSIBLE CAUSE' LISTED IN TOPIX, THERE MAY BE AN AIR LEAK IN THE EXHAUST SYSTEM. CARRY OUT A LEAK CHECK OF THE EXHAUST SYSTEM AND FOLLOW THE ACTIONS AS DETAILED BELOW:"

TYRE PRESSURE MONITORING SYSTEM (TPMS) WARNING MESSAGES. CUSTOMERS AND RETAILERS HAVE BEEN UNABLE TO RE-INFLATE AND MAINTAIN SERVICE PRESSURES DUE TO LEAKAGE FROM THE TPMS VALVES. ISSUE MAY AFFECT: 15MY AND 16MY RANGE ROVER EVOQUE, DISCOVERY SPORT, RANGE ROVER (ALL NEW), DISCOVERY 4/LR4, RANGE ROVER SPORT VEHICLES. CAUSE: RETAILER TECHNICIANS HAVE OBSERVED TPMS VALVES WHERE THERE IS EVIDENCE OF AIR LOSS OR LEAKAGE FROM THE BASE OF THE VALVE STEM OR THROUGH THE TPMS VALVE CORE ."

CAUSE: INVESTIGATIONS SHOW THE BOLTS THAT CONNECT THE TURBOCHARGER TO THE DOWNPIPE (2.0L GTDI GASOLINE ENGINES) OR TURBOCHARGER TO MANIFOLD (2.2L DIESEL ENGINES) ARE INSECURE OR MISSING."

RELEASED OR THERE MAY BE A FLASHING GEAR SELECTOR LED INDICATOR ON THE INSTRUMENT CLUSTER AND TRANSMISSION CONTROL SWITCH. AN IGNITION CYCLE IS REQUIRED TO RE-START THE ENGINE. CAUSE: THIS MAY BE DUE TO AN ANTI-LOCK BRAKING SYSTEM (ABS) CONTROL MODULE SOFTWARE ERROR THAT, UNDER VERY SPECIFIC CIRCUMSTANCES, CAUSES THIS TO OCCUR."

ROUGH IDLE, HESITATION AND/OR LOSS OF POWER. ONE OR MORE OF THE FOLLOWING DTCS MAY BE SET IN THE PCM: P008A, P008B, P2542. CAUSE: SUB-OPTIMAL PCM SOFTWARE CALIBRATION"

P162F DTC STORED. STARTER MOTOR DISABLED - ENGINE CRANK TIME TOO LONG. CAUSE: SUB-OPTIMAL PCM SOFTWARE ON VEHICLES WITHIN THE Q511 CAMPAING VIN RANGE."

RESTARTS IN XXX MILES, DIESEL EXHAUST FLUID DOSING MALFUNCTION WARNING MESSAGE DISPLAYED WITHIN THE INSTRUMENT CLUSTER MESSAGE CENTER AND DTCS P208B-00/P2BAE-00/P2BAF-00 STORED IN THE PCM (POWERTRAIN CONTROL MODULE) CAUSE: AIR IN THE SYSTEM."

EVOQUE (L538) VEHICLES WHICH MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE."

(L538) VEHICLES WHICH MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

CAUSE: THE PLANT FILL OIL HAS AN ADDITIVE TO ENABLE LEAK DETECTION AT VALENCIA ENGINE PLANT (VEP). THIS ADDITIVE HAS NO EFFECT ON THE QUALITY OR FUNCTION OF THE OIL AND IT IS STANDARD THAT THE IT MAY APPEAR TO HAVE A SLIGHTLY RED OR PINK TINT (SEE ATTACHED PICTURE)."

UPON FURTHER INVESTIGATION, A TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE (DTC) P0961-62 STORED IN THE FAULT MEMORY. CAUSE: THIS MAY BE CAUSED BY INSUFFICIENT SPRING LOAD FOR MOTOR BRUSHES IN THE ACTIVE ON-DEMAND COUPLING OIL PUMP."

(REFERRED TO AS THE POWERTRAIN CONTROL MODULE PCM ON SDD) A CUSTOMER MAY COMPLAIN OF THE HILL START ASSIST FUNCTION NOT WORKING CORRECTLY. AFFECTED VEHICLES: 14MY L538 GTDI 2.0L PETROL 856580 - 955856 15MY L538 GTDI 2.0L PETROL (NAS) 955857 - 072736 15MY L538 GTDI 2.0L PETROL (ROW) 955587 - 074612 CAUSE: A CONCERN HAS BEEN IDENTIFIED IN THE PCM SOFTWARE."

SEE ATTACHED PHOTOGRAPH. NO IMPACT DAMAGE VISIBLE. CAUSE: ENGINEERING IS INVESTIGATING THE ISSUE."

EVOQUE (L538) VEHICLES WHICH MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE"

INSTRUMENT CLUSTER: FAULTY GENERATOR FAULTY BATTERY MONITORING SYSTEM (BMS) THE CHARGE WARNING INDICATOR IS ILLUMINATED WHEN THE ENGINE IS RUNNING. CAUSE: THE POWER SUPPLY IS A FULLY INTEGRATED SYSTEM THAT REQUIRES SDD TO DIAGNOSE OVERALL FUNCTIONALITY ROBUSTLY TO MAKE SURE CUSTOMER SATISFACTION IS MET VIA RIGHT FIRST TIME DIAGNOSIS."

UPON DIAGNOSIS, THE TECHNICIAN MAY FIND NO HARDWARE FAULT AND ONE OR MORE OF THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTC) STORED IN THE POWERTRAIN CONTROL MODULE (PCM): P0044, P013A, P0300, P0301, P0302, P0303, P0304, P0420, P050B, P1315, AND/OR P2188. INFORMATION RELATING TO THE THIRD BYTE OF THE DTC IS NOT REQUIRED TO QUALIFY CODE AGAINST THIS BULLETIN.

THE DIAGNOSTIC TROUBLE CODE (DTC) THAT MAY BE LOGGED INCLUDE P0016, P0017, P0026, OR P0341.

UPON DIAGNOSIS, THE TECHNICIAN MAY FIND NO HARDWARE FAULT AND ONE OR MORE OF THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTC ) STORED IN THE ECM: P050B-92, P050B-93, P1315-00, P0300-00, P0301-00, P0302-00, P0303-00, AND/OR P0304-00. CAUSE: THIS MAY BE CAUSED BY AN ON-BOARD DIAGNOSTICS (OBD) CALIBRATION ERROR."

ILLUMINATED IN THE INSTRUMENT CLUSTER & DTC P2096-00 AND/OR P2097-00 IS EVIDENT IN THE PCM.

CAUSE ENGINEERING INVESTIGATIONS HAVE FOUND THAT THE NOISE MAY POSSIBLY IN SOME CIRCUMSTANCES, BE CAUSED BY LOOSE OBJECTS OR MATERIAL WITHIN THE BLOWER MOTOR HOUSING."

THE FOLLOWING DTC CODES, WHICH ALL RELATE TO THE 9HP48 AUTOMATIC TRANSMISSION: P0795-04 P07E3-07 P0893-07 P07E0-07 P1758-62 CAUSE: DTC FLAGGING DUE TO A TCM SOFTWARE ERROR AND/OR ENGINE TORQUE ISSUE."

DOOR LATCH CONCERNS AND THEREFORE REQUEST MORE INFORMATION TO AID INVESTIGATIONS"

EVOQUE (L538) VEHICLES WHICH MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE."

(L538) VEHICLES WHICH MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

THE STEERING WHEEL IS INOPERATIVE. CAUSE: CURRENTLY UNDER INVESTIGATION BY ENGINEERING"

THE MALFUNCTION INDICATOR LAMP (MIL) WILL BE DISPLAYED AND DIAGNOSTIC TROUBLE CODES (DTC) P0301, P0302, P0303, P0304, AND/OR P0315 MAY BE STORED IN THE ENGINE CONTROL MODULE (ECM). NOTE: THE OWNERS HANDBOOK STATES: 'PREMIUM UNLEADED GASOLINE WITH A COST OF LIVING COUNCIL (CLC) OR ANTI KNOCK INDEX (AKI) OCTANE RATING OF 91 OR HIGHER MUST BE USED.' CAUSE: THIS MAY BE CAUSED BY VARIABLE FUEL QUALITY."

NO LEAKS ARE FOUND AND VEHICLE PASSES VACUUM / PRESSURE TEST DURING EVACUATION AND REFILL, SYSTEM THEN WORKS AS REFILL. CAUSE DURING INITIAL EVACUATION PROCESS WITHIN THE FACTORY SMALL PIECES OF DEBRIS MAY BE DRAWN INTO THE SCHRADER VALVE EVACUATION PORTS, THIS CAN PREVENT THE VALVE FROM CLOSING CORRECTLY OR DAMAGES THE SEAL ALLOWING THE REFRIGERANT GAS (PLEASE SEE ATTACHMENT FOR EXAMPLES)"

STORED IN THE ENGINE CONTROL MODULE (ECM). CAUSE: THIS MAY BE CAUSED BY AN INTERNAL FAULT WITH THE LOW PRESSURE FUEL SENSOR."

ANALYSIS MANY ARE DEEMED AS NO FAULT FOUND. IT IS POSSIBLE DURING AN ECO STOP START THAT THE VEHICLE DOES NOT RE-START. CAUSE INCORRECT DIAGNOSIS"

DISPLAYED IN THE INSTRUMENT CLUSTER; ENGINE FAILS TO CRANK; VEHICLE MAY NOT UNLOCK / LOCK WHEN USING PASSIVE ENTRY OR WHEN PRESSING A SMART KEY BUTTON. CAUSE: THIS MAY BE CAUSED BY A 'LOCK UP' OF THE KEYLESS VEHICLE MODULE (KVM)."

THEREFORE WOULD APPRECIATE MORE INFORMATION TO AID INVESTIGATIONS. KNOWN ISSUES HAVE BEEN RESOLVED AND ASSURED VINS FOR EFFECTED MODELS ARE: EVOQUE: H021033(15MY), H920134 (PUNE) DISCOVERY 4 A756425 FREELANDER2: H432120, H911856 (PUNE)"

CAUSE: THIS MAY BE CAUSED BY THE SOFTWARE LOGIC CURRENTLY INSTALLED IN THE ENGINE CONTROL MODULE (ECM) NOT ALWAYS PROVIDING AN OPTIMUM SETTING WHICH SUITS THE RECENT IMPROVEMENTS TO THE OPERATION OF THE AUTOMATIC TRANSMISSION."

COOLANT PUMP LEAKS FROM WEEP CHAMBER. (SEE ATTACHED PICTURE)"

CAUSE: INTERNAL ISSUE WITHIN CLUTCH."

THEREFORE WOULD APPRECIATE MORE INFORMATION TO AID INVESTIGATIONS. KNOWN ISSUES HAVE BEEN RESOLVED AND ASSURED VINS FOR EFFECTED MODELS ARE: EVOQUE: H021033(15MY), H920134 (PUNE) DISCOVERY 4 A756425 FREELANDER2: H432120, H911856 (PUNE)"

TRANSMISSION DOES NOT SHIFT INTO REVERSE. THE CUSTOMER MAY ALSO NOTICE A FLASHING 'R' ON THE TRANSMISSION SELECTOR AND INSTRUMENT CLUSTER. 'TRANSMISSION FAULT' MESSAGE IS DISPLAYED IN THE MESSAGE CENTRE. REVERSE GEAR CANNOT BE SELECTED, THOUGH THE FAULT MAY CLEAR IF IGNITION IS SWITCHED OFF FOR AT LEAST 30 SECONDS. VEHICLE WILL OPERATE AS NORMAL IN ALL FORWARD GEARS. UPON INSPECTION, THE VEHICLE EXHIBITS NO RELEVANT DIAGNOSTIC TROUBLE CODES (DTCS). CAUSE: THIS PROBLEM IS CAUSED BY A SOFTWARE ERROR WITHIN THE TRANSMISSION CONTROL MODULE (TCM), AND JLR ENGINEERS ARE URGENTLY SEEKING RESOLUTION."

VEHICLE NON START OR CUTS OUT AND WILL NOT RE-START. LOW PRESSURE (IN TANK) FUEL-PUMP IS IDENTIFIED AS CAUSAL PART. CAUSE: FUEL PUMPS OR VEHICLES MAY HAVE BEEN SUBJECTED TO RUN DRY CONDITIONS PRIOR TO DELIVERY FUEL FILL DURING PRODUCTION HAS NOW BEEN INCREASED TO PREVENT THIS."

CAUSE: UNDER ENGINEERING INVESTIGATION"

THE DTC THAT MAY BE LOGGED INCLUDE P0016-76, P0341-00, P000A-00, OR P0026-00. THERE HAVE ALSO BEEN SOME REPORTS OF MISFIRE CODES BEING STORED (P03XX). CAUSE: THE PIN ON THE CAMSHAFT SPROCKET HAS BROKEN. SEE ATTACHED FILE FOR AN EXAMPLE."

VIBRATION AT IDLE IS NOTICEABLY WORSE THAN COMPARISON VEHICLES. CAUSE: INCORRECT POSITIONING OF ENGINE MOUNTS FOLLOWING REPAIRS IN SERVICE OR PRODUCTION."

SEE ATTACHED PHOTOGRAPH. NO IMPACT DAMAGE VISIBLE. CAUSE: ENGINEERING IS INVESTIGATING THE ISSUE."

WARRANTY DATA INDICATES A VOLUME OF FUEL INJECTORS BEING REPLACED IN RELATION TO THE SYMPTOM OUTLINED BELOW: VEHICLES SUFFERING FROM A MISFIRE AT COLD START AND ON SOME OCCASIONS INTERMITTENT ROUGH RUNNING AT NORMAL OPERATING TEMPERATURE, WITH VARIOUS DTC'S STORED SUCH AS P0300-00 P0301-00 P0302-00 P0304-00 P1315-00 P0316-00 CAUSE: ENGINEERING WOULD LIKE TO GAIN FURTHER UNDERSTANDING INTO THE CAUSE OF THESE FUEL INJECTOR FAILURES."

MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE.

DOWN, PARTICULARLY IF THE DRIVER HAS MOVED THE TRANSMISSION CONTROL SWITCH (TCS) TO NEUTRAL (N). IN THESE INSTANCES, A NEW IGNITION CYCLE MUST BE PERFORMED TO RESTART THE ENGINE. UPON ENGINE RESTART, A 'TRANSMISSION FAULT' MESSAGE ON THE INSTRUMENT CLUSTER (IC) MAY BE DISPLAYED IN THE INSTRUMENT CLUSTER COMBINED WITH EITHER AN INABILITY TO PULL AWAY OR FAILURE TO ENGAGE GEAR.

P2097-00 STORED IN THE POWERTRAIN CONTROL MODULE (PCM).

ILLUMINATED IN THE INSTRUMENT CLUSTER & DTC P2096-00 AND/OR P2097-00 IS EVIDENT IN THE PCM. A CONCERN IN THE PCM DIAGNOSTIC SOFTWARE HAS BEEN DISCOVERED, WHICH WHEN COMBINED WITH A SPECIFIC CUSTOMER DRIVE CYCLE CAN LEAD TO THE FALSE FLAGGING OF THIS DTC. EXHAUST SYSTEM LEAKS OUTSIDE DESIGN SPECIFICATION CAN INCREASE THE LIKELIHOOD OF REPEAT FAILURES. (JLR HAVE RECOGNISED THAT THE SUPPLIED LEAK CHECK EQUIPMENT DOES NOT FIT ON CERTAIN LC - DISCOVERY SPORT EXHAUST TAIL PIPES. A SOLUTION IS BEING SOURCED).

The error message The following error was encountered: is displayed to the user.

The DTC P0420-00 stored in the PCM indicates the primary catalyst is not operating at an optimal level.

Master Controller (IMC) may show that the module is still not up to date.

Initial diagnosis shows no fault found or no measurable quiescent drain.

no longer work

is stored within the RCM.

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341-00 and P054A-00 will be stored within the Powertrain Control Module (PCM).

Master Controller (IMC) may show that the module is still not up to date.

Initial diagnosis shows no fault found or no measurable quiescent drain.

no longer work

is stored within the RCM.

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341-00 and P054A-00 will be stored within the Powertrain Control Module (PCM).

notice that PATHFINDER does not respond even though the ?Replace ECU? button has been selected.

Examples of these may include: Exterior lighting, Interior lighting, Sun roof blinds, Steering Wheel Adjust, Eco stop start etc... One or more of these symptoms may be accompanied by DTC U1000-00 (Solid State Driver Protection Active - Driver Disabled) present in the BCM. If DTC U1000-00 is not present in the BCM do not continue with this SSM. Continue to diagnose and repair the inoperative BCM output as necessary using Topix as a guide.

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341- 00, P054A-00, P0303-00 and P0302-00 will be stored within the Powertrain Control Module (PCM).

During interrogation DTC?s P054A-00, P0014-71, P000B-00 and/or P0341- 00, P054A-00, P0303-00 and P0302-00 will be stored within the Powertrain Control Module (PCM).

This may or may not also illuminate the MIL. DTCs P168F-00, P2178-00, or P144C-00 may be stored also.

This may or may not also illuminate the MIL.

This may or may not also illuminate the MIL. DTCs P168F-00, P2178-00, or P144C-00 may be stored also.

This may or may not also illuminate the MIL. DTCs P168F-00, P2178-00, or P144C-00 may be stored also.

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

This may or may not also illuminate the MIL. DTCs P168F-00, P2178-00, or P144C-00 may be stored also.

module using Pathfinder or Symptom Driven Diagnostics (SDD) the module appears to be unresponsive to any further diagnostic commands or smart key remote operation.

This may or may not also illuminate the MIL. DTCs P168F-00, P2178-00, or P144C-00 may be stored also.

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

This may or may not also illuminate the MIL. DTCs P168F-00, P2178-00, or P144C-00 may be stored also.

This may or may not also illuminate the MIL.

module using Pathfinder or Symptom Driven Diagnostics (SDD) the module appears to be unresponsive to any further diagnostic commands or smart key remote operation.

This may or may not also illuminate the MIL.

message centre, when the vehicle ignition is switched on after the vehicle has been parked overnight. In addition a clicking noise may be heard from the Rear Junction Box when the ignition is switched on.

(HLDF) on occasions may fail to download software correctly resulting in no communications with the module and blank screen.

The concern prevents the technician from using Pathfinder to diagnose or rectify concerns with the ATCM

section 418-02 - Description and Operation ? Diagnosis and Testing) for the updated wiring repair standard and guidelines.

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

Retailers are testing the primary battery using the Midtronics EXP-1080 tester which is reporting the battery is serviceable. The vehicle then returns with the same Customer concern of ECO Stop/Start inoperative. If a Midtronics GRX-3080 is used, the primary battery fails the test. Replacement of the primary battery resolves the concern.

This will result in the Telematics Service Provider contacting the customer to confirm if theft has occurred. Until the customer confirms that no theft has occurred, they will be blocked from using various InControl features.

EITHER OF THE TWO ISSUES BELOW CAN OCCUR: THE DIAGNOSTIC TROUBLE CODES (DTCS) U2300-62 OR U2300-54 IS STORED IN THE BODY CONTROL MODULE (BCM). THE CCF LOADED INTO THE BCM CONTAINS FOUR CRITICAL MISMATCHES RELATED TO THE CCF ASSEMBLIES FOR DIFFERENT MODULES.

START UNAVAILABLE.

DURING THE PRE-DELIVERY INSPECTION (PDI) PROCESS FOR VEHICLES FITTED WITH INCONTROL TOUCH, MULTIPLE CONCERNS HAVE BEEN IDENTIFIED BY RETAILERS REGARDING SD MEMORY CARD REGISTRATION FAILURES.

GATEWAY MODULE (GWM).

START UNAVAILABLE.

CAUSE. SENSITIVITY OF THE GESTURE CONTROL SENSORS (HANDS FREE TAILGATE ACCESS) AT THE REAR OF THE VEHICLE."

MESSAGE CENTRE, WHEN THE VEHICLE IGNITION IS SWITCHED ON AFTER THE VEHICLE HAS BEEN PARKED OVERNIGHT. IN ADDITION A CLICKING NOISE MAY BE HEARD FROM THE REAR JUNCTION BOX WHEN THE IGNITION IS SWITCHED ON. CAUSE: SOFTWARE CALCULATION."

THE FOLLOWING DTCS MAY ALSO BE LOGGED: EPAS DTCS LOGGED: -B1304-16: ELECTRONIC POWER ASSISTED STEERING (EPAS) SYSTEM CIRCUIT VOLTAGE BELOW THRESHOLD -U3001-00: POWER STEERING CONTROL MODULE (PSCM) SYSTEM IMPROPER SHUTDOWN. THESE MAY BE ACCOMPANIED BY: -U0001-87 / 88 HIGH SPEED CAN BUS INVALID SERIAL DATA RECEIVED / MISSING MESSAGE. CHCM DTCS LOGGED: -U0131-00 CHASSIS CONTROL MODULE (CHCM) LOST COMMS WITH PSCM. -U3003-62 BATTERY VOLTAGE SIGNAL COMPARE FAILURE. -U0420-68 CHCM INVALID DATA RECEIVED FROM PSCM. CAUSE: THIS MAY BE CAUSED BY: -LOW BATTERY VOLTAGE. -WIRING HARNESS ISSUE (SHORT / OPEN CIRCUIT, HIGH RESISTANCE). -HIGH RESISTANCE AT EPAS EARTH TERMINAL (FOR L405/L494) G1D132 AND OR G4D178, (SEE ATTACHED DIAGRAM). OR IF ON L550/L538 HIGH RESISTANCE AT G1D122A, G1D122B, G1D122AZ AND G1D108. -POOR CONNECTION OR PIN SET CONDITION AT CONNECTOR NUMBER: C11-G1"

FROM 14MY ONWARDS L550 LAND ROVER SPORT: FROM 15MY ONWARDS WHEN FITTING A NEW REMOTE FUNCTION ACTUATOR (RFA) (REFERRED TO AS THE KEYLESS VEHICLE MODULE - KVM ON SDD) WITH A MODULE PART NUMBER OF: FK72-19H440 - AE FK72-19H440 - BE FK72-19H440 - AF FK72-19H440 - BF SDD CANNOT COMMUNICATE WITH THE RFA. THIS WILL BE DISPLAYED AS A RED X FOR THE RFA IN THE SDD VEHICLE SPECIFICATION SCREEN. CAUSE: THE NEW RFA MODULE SUPPLIED IS MANUFACTURED WITH PRE-FLASHED SOFTWARE FOR DUAL CAN VEHICLES. THESE VEHICLES ARE MULTICAN AND NOT DUAL CAN AND WILL NOT COMMUNICATE WITH SDD FOR PROGRAMMING OR UPDATE WITHOUT COMPLETING THE ACTION INSTRUCTIONS DETAILED BELOW."

THE FOLLOWING DTCS MAY ALSO BE LOGGED: EPAS DTCS LOGGED: -B1304-16: ELECTRONIC POWER ASSISTED STEERING (EPAS) SYSTEM CIRCUIT VOLTAGE BELOW THRESHOLD -U3001-00: POWER STEERING CONTROL MODULE (PSCM) SYSTEM IMPROPER SHUTDOWN. THESE MAY BE ACCOMPANIED BY: -U0001-87 / 88 HIGH SPEED CAN BUS INVALID SERIAL DATA RECEIVED / MISSING MESSAGE. CHCM DTCS LOGGED: -U0131-00 CHASSIS CONTROL MODULE (CHCM) LOST COMMS WITH PSCM. -U3003-62 BATTERY VOLTAGE SIGNAL COMPARE FAILURE. -U0420-68 CHCM INVALID DATA RECEIVED FROM PSCM. CAUSE: THIS MAY BE CAUSED BY: -LOW BATTERY VOLTAGE. -WIRING HARNESS ISSUE (SHORT / OPEN CIRCUIT, HIGH RESISTANCE). -HIGH RESISTANCE AT EPAS EARTH TERMINAL (FOR L405/L494) G1D132 AND OR G4D178, (SEE ATTACHED DIAGRAM). OR IF ON L550/L538 HIGH RESISTANCE AT G1D122A, G1D122B, G1D122AZ AND G1D108."

LIGHT SHOWING ON THE INSTRUMENT PANEL. SUBSEQUENTLY THROUGH CORRECT DIAGNOSIS, DEALERS HAVE IDENTIFIED CONTAMINATION BUILD UP EVIDENT ON THE FRONT WHEEL BEARING TONE RINGS . EXAMPLES ARE ATTACHED. CAUSE: ROOT CAUSE OF THE CONTAMINATION IS STILL BEING INVESTIGATED. HOWEVER, ANALYSIS OF RETURNED PARTS INDICATES THAT CLEANING THE TONE RINGS AND SENSORS CAN REPAIR THE VEHICLE TO AN ACCEPTABLE CONDITION WITHOUT THE NEED TO REPLACE THE BEARING AND KNUCKLE ASSEMBLY"

EXHIBIT INTERMITTENT OPERATION, CAUSING ONE OR MORE OF THE FOLLOWING ISSUES: AUDIO VOLUME WILL NOT ADJUST (UP AND/OR DOWN) RADIO SEEK BUTTONS WILL NOT OPERATE VOLUME CONTROL BUTTONS CAUSE THE RADIO STATION TO CHANGE THE INFOTAINMENT SYSTEM IS SLOW TO OPERATE (BLANK SCREEN FOLLOWED BY THE 'LAND ROVER' LOGO) DIAGNOSTIC TROUBLE CODE (DTC) U2013-02, 'SWITCH PACK, GENERAL SIGNAL FAILURE', IS STORED IN THE INSTRUMENT CLUSTER MEMORY DTC B1D21-13, 'REMOTE CONTROL SWITCH CIRCUIT OPEN', IS STORED IN THE TOUCH SCREEN MEMORY CAUSE: THIS MAY BE CAUSED BY POOR ELECTRICAL CONNECTION CONTINUITY."

NOT APPLICABLE TO VEHICLES FITTED WITH ACTIVE DRIVELINE. LOSS OF ALL WHEEL DRIVE FUNCTIONALITY CAUSING THE VEHICLE TO OPERATE IN 2 WHEEL DRIVE ONLY.CAUSE: DURING REPLACEMENT AND CONFIGURATION OF A NEW RDCM, DAMAGE MAY BE CAUSED TO THE PRINTED CIRCUIT BOARD (PCB) WITHIN THE RDCM DUE TO THE CONNECTION OF THE BATTERY EARTH CABLE."

CAUSE: THIS MAY BE DUE TO A POWERTRAIN CONTROL MODULE (PCM) SOFTWARE ISSUE."

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE(TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE."

CAUSE: PARK ASSIST MODULE (PAM) SOFTWARE CONCERN."

RANGE ROVER SPORT (L494), AND RANGE ROVER (L405) VEHICLES WHERE THE BLINDSPOT MONITORING CONTROL MODULE (BMCM) MAY EXPERIENCE WATER INGRESS. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN"

DISPLAYED ON THE INSTRUMENT CLUSTER. DIAGNOSTIC TROUBLE CODES (DTC) P0745-92, P0942-92, P0C06-00, P18A5-64, U0001-82, U0001-83, U0001-87, U0037-81, U0037-82, U0037-83, U0037-87, AND U3000-49 MAY BE STORED IN THE ALL WHEEL DRIVE CONTROL MODULE (AWDCM)

UPON DIAGNOSIS, A TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES (DTC ) PRESENT IN THE INTEGRATED SUSPENSION CONTROL MODULE (ISC M) OR SUSPENSION CONTROL MODULE (SUM). CAUSE: THIS MAY BE CAUSED BY DAMAGE TO THE ADAPTIVE DAMPER ELECTRICAL WIRING HARNESS."

MODULE PART NUMBER OF: FK72-19H440 - AE; FK72-19H440 - BE; FK72-19H440 - AF; FK72-19H440 - BF SDD CANNOT COMMUNICATE WITH THE RFA. THIS WILL BE DISPLAYED AS A RED X FOR THE RFA IN THE SDD VEHICLE SPECIFICATION SCREEN."

ASSOCIATED COMPONENTS REPLACED FOR A NON-START CONDITION. FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORISED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

5-DOOR ONLY) VEHICLES WHERE THERE IS A GAP IN THE SEALER BEAD THAT SECURES AND SEALS THE RIGHT-HAND REAR QUARTER WINDOW GLASS TO THE VEHICLE BODY SIDE."

IF BLOCKAGE OCCURS WHILE ACC IS BEING USED, DRIVER INTERVENE AND/OR ""RADAR SENSOR BLOCKED"" MESSAGE WILL APPEAR ON THE CLUSTER AND DTC C1A67-97 SET. BLOCKAGE CAN ALSO OCCUR WHEN ACC IS NOT BEING USED. CAUSE: ""RADAR SENSOR BLOCKED"" INDICATES THAT THE ADAPTIVE SPEED CONTROL SYSTEM'S VISIBILITY HAS BEEN REDUCED DUE TO AN OBSTRUCTION. ACC CONTINUALLY SCANS FOR OBJECTS AHEAD AND, IF IT SEES NO OBJECTS I.E. VEHICLES, ROAD SIGNS, LAMP POSTS, GUARD RAILS ETC., IT WILL INDICATE A BLOCKAGE EVEN IF THE ACC IS NOT USED. THE C1A67-97 DTC FLAGS A RADAR BLOCKAGE SITUATION AND NOT A SYSTEM FAULT."

NOTED IN THE AUXILIARY CONTROL MODULE (AUCM) DURING A SYMPTOM DRIVEN DIAGNOSTICS (SDD) FAULT CODE READ. CAUSE: SOFTWARE CALCULATION"

VEHICLES WHERE THERE IS A GAP IN THE SEALER BEAD THAT SECURES AND SEALS THE RIGHT-HAND REAR QUARTER WINDOW GLASS TO THE VEHICLE BODY SIDE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

CAUSE: QUALITY ISSUE WITH THE EXTERIOR DOOR HANDLE SENSOR."

CAUSE: DURING REPLACEMENT AND CONFIGURATION OF A NEW RDCM, DAMAGE MAY BE CAUSED TO THE PRINTED CIRCUIT BOARD (PCB) WITHIN THE RDCM DUE TO THE CONNECTION OF THE BATTERY EARTH CABLE."

FOR FAULT CODES LOGGED IN THE KVM (KEYLESS VEHICLE MODULE) ALSO KNOWN AS THE RFA (REMOTE FUNCTION ACTUATOR) F000-63/U3000-63, CONTROL MODULE - CIRCUIT/ COMPONENT PROTECTION TIME-OUT IS LOGGED. CAUSE THIS DTC IS SET WHEN THE KVM HAS GONE THROUGH A SELF RESET"

ASSOCIATED COMPONENTS REPLACED FOR A NON-START CONDITION. FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORISED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

RANGE ROVER SPORT (L494), AND RANGE ROVER (L405) VEHICLES WHERE THE BLINDSPOT MONITORING CONTROL MODULE (BMCM) MAY EXPERIENCE WATER INGRESS"

RANGE ROVER SPORT (L494), AND RANGE ROVER (L405) VEHICLES WHERE THE BLINDSPOT MONITORING CONTROL MODULE (BMCM) MAY EXPERIENCE WATER INGRESS. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

IF A BCM HAS BEEN DETERMINED TO REQUIRE REPLACEMENT FOLLOWING DIAGNOSIS, PLEASE CARRY OUT THE STEPS LISTED IN THE ACTION BELOW. CAUSE: CURRENTLY UNDER ANALYSIS."

CAUSE: THIS MAY BE CAUSED BY POOR DTC LOGGING STRATEGY FOR GATEWAY MODULE B1479 73 DTC."

CAUSE: THIS MAY BE CAUSED BY POOR DTC LOGGING STRATEGY FOR GATEWAY MODULE B1479 73 DTC."

LINE DISPLAY FRONT (HLDF), MAY BE WRONGLY REPLACED WHEN TROUBLESHOOTING IF ISSUES ARE INCORRECTLY ATTRIBUTED TO IT. CAUSE: THE TS MAY BE INCORRECTLY DIAGNOSED AS THE SOURCE OF THE FAULT AND REPLACED IN ERROR."

CAUSE: THIS MAY BE CAUSED BY AUTOMATIC TEMPERATURE CONTROL MODULE (ATCM) CALIBRATION, ALLOWING THE EVAPORATOR TO CYCLE BELOW FREEZING."

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE (TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE"

ACTION WHEN YOU SWITCH ON THE IGNITION AND HEADLAMPS IF THE BALLAST MODULE HAS FAILED YOU CAN CLEARLY HERE A TICKING AS THE BALLAST MODULE IS TRYING TO STRIKE. THESE TICKS ARE RAPID (SOUND LIKE A BIRD CHEEPING) AND SOUND 10 TIMES BEFORE SWITCHING OFF. TO CONFIRM THE BALLAST MODULE IS AT FAULT REPEAT THE PROCEDURE, THE LAMPS AND THE BALLAST MODULE WILL RETRY AND AGAIN PRODUCE THE TICKING SOUND IF THE BALLAST MODULE IS AT FAULT"

CAUSE: THIS MAY BE CAUSED BY A CORRODED WIRING HARNESS AT THE FRONT AND/OR REAR BUMPER HARNESSES."

CAUSE ALTERNATORS ARE BEING DAMAGED DUE TO CROSS POLARITY WHEN THE VEHICLE IS JUMP STARTED."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD"

MODEL 2015 RANGE ROVER, SPORT, EVOQUE, LR4. *PE

MODEL 2015 LR4, EVOQUE, SPORT, RANGE ROVER. *PE

MODEL 2014-15 RANGE ROVER EVOQUE, LR4. *PE UPDATED 6/26/15. *PE

to be the wrong spec / colour for the vehicle.

to be the wrong spec / colour for the vehicle.

Contact between the tailgate and other panels resulting in paint rub. Damaged tailgate latch cover and/or striker.

Contact between the tailgate and other panels resulting in paint rub. Damaged tailgate latch cover and/or striker.

which demonstrates the issue.

They may also report an error message "Top is not locked, less than 50km/h drive". This error has been observed during static position and whilst moving.

that the door(s) sound different (rings) when compared to the other original factory fitted doors.

Contact between the tailgate and other panels resulting in paint rub. Damaged tailgate latch cover and/or striker.

Contact between the tailgate and other panels resulting in paint rub. Damaged tailgate latch cover and/or striker.

Contact between the tailgate and other panels resulting in paint rub. Damaged tailgate latch cover and/or striker.

which demonstrates the issue.

They may also report an error message "Top is not locked, less than 50km/h drive". This error has been observed during static position and whilst moving.

that the door(s) sound different (rings) when compared to the other original factory fitted doors.

Contact between the tailgate and other panels resulting in paint rub. Damaged tailgate latch cover and/or striker.

Contact between the tailgate and other panels resulting in paint rub. Damaged tailgate latch cover and/or striker.

Contact between the tailgate and other panels resulting in paint rub. Damaged tailgate latch cover and/or striker.

washer pump and fluid being present in the reservoir.

DOOR MIRROR ON L538 2. THE GLASS RUN SEAL TUCKS IN ON THE GLASS RUN LOWER CHANNEL ON L550 3. BOTH VARIANTS PRODUCE A SQUEAK WHEN THE WINDOW RAISE/LOWER FUNCTION IS OPERATED CAUSE: GLASS RUN SEAL LOOSES THE FLOCK AND THIS INCREASES THE FRICTION BETWEEN THE GLASS AND THE SEAL."

CAUSE: THE GLASS, WHEN INSPECTED, SHOWS CLEAR IMPACT MARKS WHERE AN OBJECT HAS HIT THE GLASS INITIATING THE CRACK."

CAUSE: THIS MAY BE CAUSED BY OIL WEEPING FROM THE DETENT SEALING CAP."

CAUSE: THIS MAY BE CAUSED BY VARIATION IN THE DENSITY OF THE FIBER STRUCTURE WITHIN ONE HIDE AND/OR FROM HIDE-TO-HIDE CREATING A WRINKLED APPEARANCE ON LAMINATED LEATHER. THE FRONT SEAT CUSHION COVERS INSERT PANELS ARE MORE SUSCEPTIBLE TO THIS ISSUE.."

CAUSE: OIL FILTER LR001247 SUPERSEEDS TO LR030778 WHICH IS SUPPLIED WITH A NEW SEAL. THIS SEAL IS SLIGHTLY LARGER IN DIAMETER THAN THE ONE SUPPLIED WITH LR001247"

WHICH DEMONSTRATES THE ISSUE.

CAUSE: THIS MAY BE CAUSED BY A BUILD-UP OF DIRT AND GREASE ON THE SURFACE OF THE WINDSHIELD GLASS."

CAUSE: THIS MAY BE DUE TO STRESS APPLIED TO THE BOTTOM OF THE FRONT BUMPER COVER CAUSING THE TOP SECTION OF THE FRONT BUMPER COVER TO CRACK WHERE IT MEETS THE FRONT FENDER."

CAUSE: THIS MAY BE CAUSED BY HINGE PIN DISTORTION, ALLOWING THE CAM MECHANISM TO BE DISPLACED AND NOT ALLOWING THE HOLDER TO OPEN AND/OR CLOSE."

CAUSE: THIS MAY BE DUE TO STRESS APPLIED TO THE BOTTOM OF THE FRONT BUMPER COVER CAUSING THE TOP SECTION OF THE FRONT BUMPER COVER TO CRACK WHERE IT MEETS THE FRONT FENDER."

VEHICLES WHERE THE OVERHEAD CONSOLE SUNGLASSES HOLDER DOES NOT REMAIN CLOSED AND/OR SUNGLASSES MAY RATTLE WHEN STOWED."

VEHICLES WHERE THE OVERHEAD CONSOLE SUNGLASSES HOLDER DOES NOT REMAIN CLOSED AND/OR SUNGLASSES MAY RATTLE WHEN STOWED. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

CAUSE: THIS MAY BE CAUSED BY HINGE PIN DISTORTION, ALLOWING THE CAM MECHANISM TO BE DISPLACED AND NOT ALLOWING THE HOLDER TO OPEN OR CLOSE."

BECOME PITTED IN APPEARANCE CAUSE PLATING PROCESS OUT OF SPECIFICATION CAUSING BLEMISHES ON THE OUTER SURFACE."

COOLANT LEVEL' ON 2.0GTDI L538 (EVOQUE) VEHICLES. ACTION: IN ALL CASES WHEREBY A TECHNICIAN IDENTIFIES THE SYMPTOMS DETAILED IN LTB00502V2 (RE-SEAL OF CORE PLUGS) BUT THE VEHICLE IS NOT WITHIN THE VIN RANGE (H000001-H750389), PLEASE RAISE A TA BEFORE ANY REPAIR WORK IS CARRIED OUT AND THE TECHNICAL ASSISTANT WILL ADVISE YOU ACCORDINGLY."

CONTACT BETWEEN THE TAILGATE AND OTHER PANELS RESULTING IN PAINT RUB. DAMAGED TAILGATE LATCH COVER AND/OR STRIKER."

SECONDARY SEAL.

CAUSE. THIS MAY BE CAUSED BY NOT POSITIONING THE ELECTRONIC TOLL TAG PROPERLY IN THE INFRARED RADIATION REFLECTIVE (IRR) LAYER CUT OUT ON THE WINDSHIELD. .

TAILGATE AND OTHER PANELS RESULTING IN PAINT RUB.DAMAGED TAILGATE LATCH COVER AND/OR STRIKER.

OVERHEAD SUNGLASSES HOLDER APPEARS TO BE DISTORTED AND WILL NOT LATCH CORRECTLY IN CERTAIN CONDITIONS.

*PE

to respond or no functionality at all.

versions.

The concern will only affect New Low line Infotainment (NLI) systems.

The concern will only affect New Low line Infotainment (NLI) systems

Examples of this may include: No infotainment audio, No audio from Park Aid, No audio from Rear Seat Entertainment, Customers with Telematics fitted may also report that internet connectivity is inoperative.

Examples of this may include: No infotainment audio, No audio from Park Aid, No audio from Rear Seat Entertainment, Customers with Telematics fitted may also report that internet connectivity is inoperative.

The concern will only affect New Low line Infotainment (NLI) systems

is not available? displayed on the instrument Cluster? due to activation failure.

Bluetooth the user may experience a connectivity issues.

inoperative

.The concern occurs when updating to phase 4.0 using PATHFINDER 180

Bluetooth the user may experience a connectivity issues.

inoperative

.The concern occurs when updating to phase 4.0 using PATHFINDER 180

Bluetooth the user may experience a connectivity issues.

Bluetooth the user may experience a connectivity issues.

Bluetooth the user may experience a connectivity issues.

left or right tune soft key buttons or when selecting an alternative radio band (ie trying to change from FM to DAB) there is no response from touch screen and audio output remains distorted. The DTC B14D3-96 may also be stored in the Infotainment Master Controller (IMC) suggesting a radio tuner component internal failure.

the InControl Touch Pro system, or cause system functionality concerns after the infotainment system was successfully updated.

the InControl Touch Pro system, or cause system functionality concerns after the infotainment system was successfully updated.

the InControl Touch Pro system, or cause system functionality concerns after the infotainment system was successfully updated.

longer process voice inputs or outputs. Common symptoms are reported as: Voice commands are not recognized. Voice output such as spoken navigation guidance is inoperative.

IT WILL ALSO NOT BE POSSIBLE TO OPEN THE LUGGAGE/TAILGATE AND THE GLOVE BOX.

IN ADDITION THE CURRENT VEHICLE LOCATION INDICATOR WILL NOT LOCK ONTO THE CORRECT LOCATION ON THE MAP. CAUSE: SOFTWARE ERROR."

THERE MAY ALSO BE AN OIL SMELL IN THE VEHICLE CABIN.

DIAGNOSTIC TROUBLE CODES (DTC) ARE STORED. CAUSE: THIS MAY BE CAUSED BY VARIOUS ISSUES."

CAUSE VIN NUMBER HAS BEEN INCORRECTLY ENTERED WHEN MANUALLY PROCESSING."

WHICH IS NOT COMPATIBLE WITH LAND ROVER INFOTAINMENT SYSTEMS. CAUSE THIS IS TO MAKE YOU AWARE OF THE TYPES OF MEDIA THAT MAY CAUSE THE UNIT TO FAIL WITH THE CUSTOMER."

LOCKED) WHEN THE SD CARD IS IN LOCKED POSITION THE HEAD UNIT MAY NOT DETECT THE CARD."

'HOOD OPEN' MESSAGE IS DISPLAYED ON THE INSTRUMENT CLUSTER; AND/OR A MISLOCK SOUND IS EMITTED WHEN LOCKING THE VEHICLE. CAUSE: THESE ISSUES MAY BE CAUSED BY A FAULTY HOOD OPEN SWITCH."

CAUSE: IT HAS BEEN IDENTIFIED THAT WHEN THE KEY PROGRAMMING APPLICATION IS AT TEMPTED IT FAILS TO COMPLETE AND DISPLAYS A MESSAGE OF FAILED TO START THE KEY PROGRAM ROUTINE. THIS DOES NOT AFFECT AL L VEHICLES ONLY VEHICLES THAT HAVE HARDWARE LEVEL WITH SUFFIX DPLA."

CAUSE: SOFTWARE COMPATIBILITY ISSUES"

TEMPERATURES.

the following TCM DTC codes during SDD DTC read (which are all related to 9HP48 automatic transmission). P07D4-07, P2704-07, P07E7-07

Transmission: Retailers reporting these vehicles are flagging the following (TCM) Transmission control module DTC?s P2545-86 and/or P2546-86 codes during SDD DTC read or on customer concern. Should there be any other transmission related fault codes stored in the TCM these other codes should be investigated and resolved before proceeding with this instruction.

P0893-07 WHICH ARE RELATED TO THE 9HP48 AUTOMATIC TRANSMISSION. CAUSE: INTERNAL TRANSMISSION DIAGNOSTICS HAVE BEEN TRIGGERED - ISSUES NOW RESOLVED."

CAUSE: THIS MAY BE CAUSED BY THE TRANSMISSION COVER GASKET HAVING BEEN DAMAGED DURING MANUFACTURE, ALLOWING TRANSMISSION FLUID TO LEAK."

CRUISE CONTROL) AND TRANSMISSION PADDLE SWITCHES MAY EXHIBIT INTERMITTENT OPERATION, CAUSING ONE OR MORE (LIST NOT EXHAUSTIVE) OF THE FOLLOWING ISSUES: AUDIO VOLUME WILL NOT ADJUST (UP AND/OR DOWN) RADIO SEEK BUTTONS WILL NOT OPERATE VOLUME CONTROL BUTTONS CAUSE THE RADIO STATION TO CHANGE THE INFOTAINMENT SYSTEM IS SLOW TO OPERATE (BLANK SCREEN FOLLOWED BY THE 'LAND ROVER' LOGO) DIAGNOSTIC TROUBLE CODE (DTC) U2013-02 'SWITCH PACK, GENERAL SIGNAL FAILURE' IS STORED IN THE INSTRUMENT CLUSTER MEMORY DTC B1D21-13 'REMOTE CONTROL SWITCH CIRCUIT OPEN' IS STORED IN THE TOUCH SCREEN MEMORY TRANSMISSION PADDLE SWITCHES INOPERATIVE OR INTERMITTENT FUNCTIONALITY CRUISE CONTROL INOPERATIVE"

THE FOLLOWING TCM DTC CODES DURING SDD DTC READ (WHICH ARE ALL RELATED TO 9HP48 AUTOMATIC TRANSMISSION). P07D4-07 P2704-07 P07E7-07 CAUSE: INTERNAL TRANSMISSION DIAGNOSTICS HAVE BEEN TRIGGERED. MULTIPLE ROOT CAUSES EXIST."

MODEL YEAR RANGE ROVER EVOQUE (L538) WHERE AN IRREGULAR GEAR CHANGE OCCURS OR NEUTRAL IS SELECTED. ADDITIONALLY, DIAGNOSTIC TROUBLE CODE (DTC) P1758-62 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM)."

(L538) VEHICLES WHERE THE TRANSMISSION CONTROL MODULE SOFTWARE WILL BE UPDATED TO THE LATEST LEVEL."

MODEL YEAR RANGE ROVER EVOQUE (L538) WHERE AN IRREGULAR GEAR CHANGE OCCURS OR NEUTRAL IS SELECTED. ADDITIONALLY, DIAGNOSTIC TROUBLE CODE (DTC) P1758-62 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM). ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

UPON DIAGNOSIS, DIAGNOSTIC TROUBLE CODE (DTC) P1889-14 IS FOUND TO BE STORED. CAUSE: THIS MAY BE CAUSED BY INSUFFICIENT SPRING LOAD FOR COMMUTATOR BAR BRUSHES IN THE ACTIVE ON-DEMAND COUPLING OIL PUMP."

DIAGNOSTIC TROUBLE CODES (DTC) STORED IN THE TRANSMISSION CONTROL MODULE (TCM): P0600-04, P0710-27, P0710-64, P0712-11, P0713-13, P0975-19, P0978-19, P0981-19, AND P0984-19. CAUSE: THIS MAY BE CAUSED BY A FAULTY CRIMP ON THE TRANSMISSION INTERNAL WIRING HARNESS."

WHERE THE TRANSMISSION CONTROL MODULE SOFTWARE WILL BE UPDATED TO THE LATEST LEVEL. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

DIAGNOSTIC TROUBLE CODES (DTC) STORED IN THE TRANSMISSION CONTROL MODULE (TCM): P0600-04, P0710-27, P0710-64, P0712-11, P0713-13, P0975-19, P0978-19, P0981-19, AND P0984-19. CAUSE: THIS MAY BE CAUSED BY A FAULTY CRIMP ON THE TRANSMISSION INTERNAL WIRING HARNESS."

THERE MAY BE NO FAULT CODES OR WARNING LIGHTS PRESENT. CAUSE: SIDE IMPACT TO THE VEHICLE WHEELS."

CAUSE: INTERNAL TRANSMISSION DIAGNOSTICS HAVE BEEN TRIGGERED."

(L538) VEHICLES WHERE THE TRANSMISSION CONTROL MODULE SOFTWARE WILL BE UPDATED TO THE LATEST LEVEL."

(L538) VEHICLES, WHERE ONE OR MORE OF THE FOLLOWING MAY BE EXHIBITED: H POOR TRANSMISSION SHIFT QUALITY; H WARNING MESSAGE (TRANSMISSION ISSUE); H LACK OF POWER; AND/OR H UNABLE TO SELECT DRIVE (D) OR REVERSE (R) WHEN THE VEHICLE IS IN PARK (P)."

TRANSMISSION MAY EXHIBIT ROUGH/JERKY OR DELAYED SHIFTS."

WHERE THE TRANSMISSION CONTROL MODULE SOFTWARE WILL BE UPDATED TO THE LATEST LEVEL. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

RELATE TO THE 9HP48 AUTOMATIC TRANSMISSION: P0795-04 P07E3-07 P0893-07 CAUSE: INTERNAL TRANSMISSION DIAGNOSTICS HAVE BEEN TRIGGERED ISSUES NOW RESOLVED."

ISSUE: A TECHNICIAN MAY FIND WHEN REPLACING THE M66 GEARBOX TURRET HOUSING FOR A GEAR CHANGE SELECTION OR STOP/START FAULT THAT AN INCORRECT TURRET MAY BE SUPPLIED. THIS AFFECTS: VEHICLES FITTED WITH M66 6 SPEED MANUAL TRANSMISSIONS FREELANDER 2/LR2 (LF) MODEL YEAR: 2013-2014 (VIN: DH321215-EH439912) RANGE ROVER EVOQUE (LV) MODEL YEAR: 2013 ONWARDS (VIN: DH85818 ONWARDS) CAUSE: IN MARCH 2013 A HALL EFFECT SENSOR TURRET WAS INTRODUCED, BUT WAS NOT GIVEN A SERVICE PART NUMBER. DEALERS ORDERING PART NO.LR022071 MAY HAVE EITHER THE AN INDUCTIVE OR HALL EFFECT TURRET SUPPLIED. THIS MAY BE INCORRECT FOR THE VEHICLE BEING REPAIRED."

THERE MAY BE NO FAULT CODES OR WARNING LIGHTS PRESENT. CAUSE: SIDE IMPACT TO THE VEHICLE WHEELS."

(L538) VEHICLES, WHERE ONE OR MORE OF THE FOLLOWING MAY BE EXHIBITED: H POOR TRANSMISSION SHIFT QUALITY; H WARNING MESSAGE (TRANSMISSION ISSUE); H LACK OF POWER; AND/OR H UNABLE TO SELECT DRIVE (D) OR REVERSE (R) WHEN THE VEHICLE IS IN PARK (P)."

VEHICLES WHERE ONE OR MORE OF THE FOLLOWING MAY BE EXHIBITED: POOR TRANSMISSION SHIFT QUALITY; WARNING MESSAGE (TRANSMISSION ISSUE); LACK OF POWER; AND/OR UNABLE TO SELECT DRIVE (D) OR REVERSE (R) WHEN THE VEHICLE IS IN PARK (P). ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

(L538) VEHICLES, WHERE ONE OR MORE OF THE FOLLOWING MAY BE EXHIBITED: H POOR TRANSMISSION SHIFT QUALITY; H WARNING MESSAGE (TRANSMISSION ISSUE); H LACK OF POWER; AND/OR H UNABLE TO SELECT DRIVE (D) OR REVERSE (R) WHEN THE VEHICLE IS IN PARK (P)."

TRANSMISSION MAY EXHIBIT ROUGH/JERKY OR DELAYED SHIFTS."

VEHICLES WHERE ONE OR MORE OF THE FOLLOWING MAY BE EXHIBITED: POOR TRANSMISSION SHIFT QUALITY; WARNING MESSAGE (TRANSMISSION ISSUE); LACK OF POWER; AND/OR UNABLE TO SELECT DRIVE (D) OR REVERSE (R) WHEN THE VEHICLE IS IN PARK (P). ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

VEHICLES WHERE THE TRANSMISSION MAY EXHIBIT ROUGH/JERKY OR DELAYED SHIFTS. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

AUTOMATIC TRANSMISSION: RETAILERS REPORTING THESE VEHICLES ARE FLAGGING THE FOLLOWING (TCM) TRANSMISSION CONTROL MODULE DTCS P2545-86 AND/OR P2546-86 CODES DURING SDD DTC READ OR ON CUSTOMER CONCERN. SHOULD THERE BE OTHER TRANSMISSION RELATED FAULT CODES IN ADDITION THESE OTHER CODES SHOULD BE INVESTIGATED AND RESOLVED BEFORE PROCEEDING WITH THIS INSTRUCTION. ISSUE: TRANSMISSION CONTROL MODULE (TCMS) ARE BEEN REPLACED UNDER WARRANTY AND ON INVESTIGATION ON RETURNED PARTS HAVE FOUND WITH NO FAULT FOUND."

THE FOLLOWING TCM DTC CODES DURING SDD DTC READ (WHICH ARE ALL RELATED TO 9HP48 AUTOMATIC TRANSMISSION). P07D4-07P2704-07P07E7-07

Onwards

Driven Diagnostics (SDD) does not appear to communicate with the RFA: FK72-19H440-AE, FK72-19H440-BE, FK72-19H440-AF, FK72-19H440-BF, Following models only affected: L538 Range Rover Evoque 14MY onwards, L550 Discovery Sport 15MY onwards, L494 Range Rover Sport 14MY onwards, L405 Range Rover 14MY onwards

This can cause the alarm to trigger or the vehicle to not lock.

wrinkled, misshapen or creased.

HALOGEN BULB - LR044458. CAUSE: LTB00841 HAS BEEN TEMPORARILY REMOVED FROM TOPIX IN ORDER TO PROCURE SUFFICIENT PARTS FROM JLR SUPPLIERS - PARTS ARE DUE TO BE MADE AVAILABLE TO MARKETS IN WEEK 4 OF 2016, UPON WHICH, THE BULLETIN WILL BE RELEASED FOR PUBLICATION."

HALOGEN BULB - LR044458. CAUSE: LTB00841 HAS BEEN TEMPORARILY REMOVED FROM TOPIX IN ORDER TO PROCURE SUFFICIENT PARTS FROM JLR SUPPLIERS."

CAUSE: THIS MAY LEAD TO EARLIER THAN EXPECTED BULB REPLACEMENT."

THIS CAN CAUSE THE ALARM TO TRIGGER OR THE VEHICLE TO NOT LOCK.

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES"

CAUSE: DAMAGE/MARKING CAUSED BY OBJECT IMPACT AGAINST THE LENS. STAINING/DISCOLORATION CONTAMINATION CAUSED BY USING ANY TYPE OF CLEANING PRODUCT ON LENS. IMPORTANT: OWNERS HANDBOOK SPECIFIES TO CLEAN WITH A LIGHTLY MOISTENED CLOTH AND DO NOT USE CHEMICAL AGENTS OR DOMESTIC CLEANERS ACTION WHERE A CUSTOMER CONCERN IS REPORTED, PLEASE ORDER THE LENS KIT FOR THE RELEVANT MODEL"

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OUTSIDE OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE PERFORMANCE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES."

instrument cluster.

booster during replacement.

The EPB applied light is not on. The ABS (Anti-lock braking system), DSC (Dynamic stability Control) and brake warning lights are on. The "Autonomous Emergency Braking not available" message is displayed.

The EPB applied light is not on. The ABS (Anti-lock braking system), DSC (Dynamic stability Control) and brake warning lights are on. The "Autonomous Emergency Braking not available" message is displayed.

EPQR & TA data provided by retailers to date, shows a varied range of conditions (environmental, drive cycle and road type) that may initiate the known noises. Although the noises do not, in most cases, indicate a degradation in functionality or braking performance, they may lead to customer dissatisfaction and unscheduled retailer visits for repair action. Note: Off road use of the vehicle is not categorised in the communication due to the extended range of parameters and conditions that the vehicle operate at. Defining and describing brake noises is proven to be difficult through our different languages and terminology. In the ?Solutions? section below, there are noise descriptions and Technical Service Bulletins references to aid the repair selection. See ?Action? for further guidance.

EPQR & TA data provided by retailers to date, shows a varied range of conditions (environmental, drive cycle and road type) that may initiate the known noises. Although the noises do not, in most cases, indicate a degradation in functionality or braking performance, they may lead to customer dissatisfaction and unscheduled retailer visits for repair action. Note: Off road use of the vehicle is not categorised in the communication due to the extended range of parameters and conditions that the vehicle operate at. Defining and describing brake noises is proven to be difficult through our different languages and terminology. In the ?Solutions? section below, there are noise descriptions and Technical Service Bulletins references to aid the repair selection. See ?Action? for further guidance.

CAUSE: THIS MAY BE CAUSED BY WATER ENTERING THE DOOR PAD INSERT VIA THE OPEN PORES IN THE PERFORATIONS OF THE LEATHER."

CAUSE: DAMAGE TO THE CALIPER FINISH WHILE CLEANING THE VEHICLE AND, OR THE ROAD WHEELS"

CAUSE: THIS MAY BE CAUSED BY WATER ENTERING THE DOOR PAD INSERT VIA THE OPEN PORES IN THE PERFORATIONS OF THE LEATHER."

CAUSE: THIS MAY BE CAUSED BY WATER ENTERING THE DOOR PAD INSERT VIA THE OPEN PORES IN THE PERFORATIONS OF THE LEATHER."

VIBRATION/JUDDER WHILE BRAKING.

air conditioning compressor.

For example: Seat heating or cooling inoperative, Intermittent operation, Noisy operation, Poor heating or cooling efficiency, Heating or cooling operation slow.

NO LEAKS ARE FOUND AND VEHICLE PASSES VACUUM/PRESSURE TEST DURING EVACUATION AND REFILL, SYSTEM THEN WORKS AS NORMAL AFTER REFRIGERANT REFILL.

COMMUNICATION ISSUES ON THE LIN BUS. THE COMMUNICATION CEASES UPON SHUTDOWN AND DOES NOT RECOVER UPON WAKE UP. SYMPTOMS INCLUDE: DTCS. HVAC BLOWER BECOMES INOPERATIVE BECAUSE THERE IS NO STEPPER CONTROL. NO LIN COMMUNICATION TO THE SEATS AND THEREFORE, NO CLIMATE SEAT CONTROL. CAUSE: HVAC SOFTWARE."

INSTRUMENT PACK EVEN THOUGH THE HOOD / BONNET IS CLOSED CAUSE: THERE IS A POTENTIAL THAT AN INTERNAL SPRING COULD BECOME DISLODGED"

CAUSE: THIS MAY BE CAUSED BY 'STICK/SLIP' BETWEEN THE STABILIZER BAR BUSHING AND THE STABILIZER BAR."

CAUSE: THIS MAY BE CAUSED BY METAL-TO-METAL CONTACT BETWEEN THE SEAT SUSPENSION MAT HOOKS AND THE SEAT FRAME AND MAY BE VERIFIED BY VISUAL INSPECTION OF SEAT SUPPORT MAT LOCATION HOLE WEAR."

CAUSE: THIS MAY BE CAUSED BY METAL-TO-METAL CONTACT BETWEEN THE SEAT SUSPENSION MAT HOOKS AND THE SEAT FRAME AND MAY BE VERIFIED BY VISUAL INSPECTION OF SEAT SUPPORT MAT LOCATION HOLE WEAR."

VEHICLES WHERE THE FRONT SUSPENSION LOWER CONTROL ARM-TO-KNUCKLE BOLT(S) FAILED WHEN HAVING THE SERVICE INSTRUCTION CONTAINED IN PROGRAM CODE Q382 PERFORMED DUE TO THE SPECIFIED TORQUE SPECIFICATION (175NM) BEING INCORRECT."

WHERE THE FRONT SUSPENSION LOWER CONTROL ARM-TO-KNUCKLE BOLT(S) FAILED WHEN HAVING THE SERVICE INSTRUCTION CONTAINED IN PROGRAM CODE Q382 PERFORMED DUE TO THE SPECIFIED TORQUE SPECIFICATION (175NM) BEING INCORRECT. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

ON ROUGH ROADS FOR A SHORT PERIOD OF TIME AT LOWER AMBIENT TEMPERATURES. NOTE: THIS ISSUE IS VERY RARELY SEEN OUTSIDE OF THE CENTRAL AND NORTHERN EUROPEAN MARKETS. CAUSE: THIS MAY BE CAUSED BY MANUFACTURING BUSH LUBRICATION AND MATERIAL PROPERTIES AFFECTING A SMALL NUMBER OF VEHICLES DUE TO CLIMATIC CONDITIONS AND EXCESSIVE BUSH LUBRICANT BEING APPLIED DURING VEHICLE BUILD."

ARM TO KNUCKLE BOLT(S) HAD FAILED AND INFORMATION NEEDS UPDATING. MODEL 2014-15 EVOQUE. *PE

We require all retailers to follow the procedure outlined below ahead of conducting wheel alignment warranty work on Evoque (L538), Discovery Sport (L550), RR (L405), RRS (L494), Discovery (L462), and Velar (L560).

HALEWOOD BUILT VEHICLES ONLY - IDENTIFIED BY THE 11TH DIGIT OF THE VIN = 'H' FREELANDER 2 (L359) VEHICLES VIN: ALL EVOQUE (L538) VEHICLES UPTO VIN: H991051. PUNE BUILT VEHICLES ONLY - IDENTIFIED BY THE 11TH DIGIT OF THE VIN = 'L') FREELANDER (L359) VEHICLES VIN: ALL EVOQUE (L538) VEHICLES VIN: N/A (NOT AFFECTED)"

CAUSE: THIS IS EITHER CAUSED BY THE SHIPPING PROCESS AND SHOULD BE CLAIMED THROUGH TRANSPORT / DISTRIBUTION OR IT IS CAUSED DURING JLR MANUFACTURING PROCESSES AND SHOULD BE CLAIMED AS PER WARRANTY POLICY."

The areas around the stitching and spokes, or the lower half of the steering wheel, may appear cooler than the rest of the wheel. The heated steering wheel is otherwise operating correctly, and no DTCs are stored.

BY VISUAL OR AUDIBLE WARNINGS THROUGH THE INSTRUMENT PACK.

CAUSE: UNDER INVESTIGATION"

THE ISSUE IS COMMON ACROSS ALL MANUFACTURERS SYMPTOMS WHEN THE APPLE DEVICE IS CONNECTED TO THE CAR SYSTEM AND A CALL IS RECEIVED THERE IS NO OPTION TO ANSWER OR REJECT THE INCOMING CALL ON THE SYSTEM. THE STEERING WHEEL CONTROLS ALSO HAVE NO EFFECT. THE TOUCH SCREEN CONTINUES TO DISPLAY THE PHONE SCREEN. THE POP-UP SCREEN TO ANSWER OR REJECT THE CALL IS NOT SHOWN."

CAUSE: THIS MAY BE CAUSED BY A POOR GROUND."

AND MATERIALS ACROSS THE VEHICLE INTERIOR THAT HAVE MADE CONTACT WITH THE ICP AND OR ROTARY DIALS."

-40 DEGREES).

This is only a temporary position and will be included in a future update to the publications on TOPIx.

CONTROLLER (ISC, FOR REAR SEAT ENTERTAINMENT ) THE SYSTEM MAY EXHIBIT THE FOLLOWING CONDITIONS DUE TO INCOMPLETE VARIANT CONFIGURATION LEARN PROCEDURE DURING THE SOFTWARE UPDATE."

Please refer to the following publications on TOPIx for the latest details. Land Rover SSM #73635

be ?No Fault Found? during part return analysis.

CAUSE: IF UPON INSPECTION THE COOLING SYSTEM DOES NOT SHOW EVIDENCE OF WHERE COOLANT MAY HAVE ESCAPED, IT IS POSSIBLE AIR WAS NOT FULLY PURGED FROM THE SYSTEM DURING THE FILL PROCESS AT THE FACTORY. OVER TIME THIS AIR WILL MOVE TO THE HEADER TANK CAUSING THE COOLANT LEVEL TO DROP."

TRANSLATED AND DISPLAYED AS 'AIRBAG FAULT'.