2014 Land Rover LR4 TSBs

A coolant leak is found from the seam on coolant pipe (LR018275)

DTC relevant to a purge valve coincern stored in the PCM DTCs below could potentially indicate a concern with the purge valve.

5.0L AJ133 engines have been updated.

returned to the supplier for analysis many are deemed as No fault found. It is possible during an ECO stop start that the vehicle does not re-start.

engine Malfunction Indicator Lamp (MIL) may be illuminated on the Instrument Cluster (IC) and Oxygen (O2) sensor performance-related Diagnostic Trouble Codes (DTC) may be stored in the Powertrain Control Module (PCM).

DTCs vary, may include P2187-00, P2189-00, P013E-00,P014E-00. Fuel trims near limit when engine is at idle speed.

Trouble Code) P132B-77 stored in the Powertrain Control Module (PCM).

Trouble Code) P132B-77 stored in the Powertrain Control Module (PCM).

Code (DTC) P132B-77 stored in the Powertrain Control Module (PCM).

MANY ARE DEEMED AS NO FAULT FOUND. IT IS POSSIBLE DURING AN ECO STOP START THAT THE VEHICLE DOES NOT RE-START. CAUSE INCORRECT DIAGNOSIS."

DISPLAYED IN THE INSTRUMENT CLUSTER; ENGINE FAILS TO CRANK; VEHICLE MAY NOT UNLOCK / LOCK WHEN USING PASSIVE ENTRY OR WHEN PRESSING A SMART KEY BUTTON.

(ECM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE.

UPON DIAGNOSIS, THE TECHNICIAN MAY FIND ONE OR MORE DIAGNOSTIC TROUBLE CODE (DTC), LISTED IN THE TABLE BELOW AND RELEVANT TO THE HEATED OXYGEN SENSORS (HO2S), MAY BE STORED IN THE ENGINE CONTROL MODULE (ECM).

ENGAGED WHEN COMING TO A STOP OR IMMEDIATELY AFTER AN AUTOMATIC ENGINE RESTART (WHEN INTELLIGENT STOP/START IS ACTIVE). THE INSTRUMENT CLUSTER HAS SWITCHED OFF AFTER AN AUTOMATIC ENGINE STOP AND DRIVER EXIT CONDITIONS DO NOT EXIST AND THE VEHICLE DOES NOT AUTOMATICALLY RESTART THE ENGINE UPON RELEASE OF THE BRAKE PEDAL (NOTE. DTC P162F-00 MAY BE STORED IN THE ENGINE CONTROL MODULE [ECM]).

TYRE PRESSURE MONITORING SYSTEM (TPMS) WARNING MESSAGES. CUSTOMERS AND RETAILERS HAVE BEEN UNABLE TO RE-INFLATE AND MAINTAIN SERVICE PRESSURES DUE TO LEAKAGE FROM THE TPMS VALVES. ISSUE MAY AFFECT: 15MY AND 16MY RANGE ROVER EVOQUE, DISCOVERY SPORT, RANGE ROVER (ALL NEW), DISCOVERY 4/LR4, RANGE ROVER SPORT VEHICLES. CAUSE: RETAILER TECHNICIANS HAVE OBSERVED TPMS VALVES WHERE THERE IS EVIDENCE OF AIR LOSS OR LEAKAGE FROM THE BASE OF THE VALVE STEM OR THROUGH THE TPMS VALVE CORE ."

CAUSE: THIS MAY BE CAUSED BY DUST AND/OR WATER INGRESS TO THE ACCESSORY DRIVE BELT IDLER PULLEY BEARING."

THE NOISE MAY BE MORE NOTICEABLE WHEN THE ENGINE IS AT IDLE SPEED AND WHEN THE ENGINE IS COLD. CAUSE: THIS MAY BE CAUSED BY A NOISY HIGH PRESSURE FUEL PUMP OUTLET VALVE."

RESTARTS IN XXX MILES, DIESEL EXHAUST FLUID DOSING MALFUNCTION WARNING MESSAGE DISPLAYED WITHIN THE INSTRUMENT CLUSTER MESSAGE CENTER AND DTCS P208B-00/P2BAE-00/P2BAF-00 STORED IN THE PCM (POWERTRAIN CONTROL MODULE) CAUSE: AIR IN THE SYSTEM."

MODULE (PCM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE."

(ECM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

IS IN USE AND ENGINE SPEED IS BETWEEN 2,000 AND 3,000 RPM. CAUSE: THIS MAY BE CAUSED BY A RESONANCE WITHIN CLIMATE CONTROL SYSTEM AIR CONDITIONING (A/C) PIPES."

INVOLUNTARILY ENGAGED WHEN COMING TO A STOP OR IMMEDIATELY AFTER AN AUTOMATIC ENGINE RESTART (WHEN INTELLIGENT STOP/START IS ACTIVE)."

AMBIENT AIR TEMPERATURE IS LOW AND THE ENGINE IDLE SPEED IS ELEVATED. VIN: 731247 ONWARDS. ENGINE: V6 S/C 3.0L PETROL. CAUSE: THE TRANSMISSION SETTING IS NOT OPTIMIZED FOR THE ENGINE SPEED OUTPUT."

CUSTOMERS OR EXTERNAL INFLUENCES SUCH AS CAR WASHES MAY INADVERTANTLY KNOCK THE DOOR MIRROR HEAD INTO THE FOLDED POSITION, THIS WILL THEN CAUSE THE MIRROR HEAD TO BE LOOSE"

ENGINE AND THE ENGINE WILL NOT START. CAUSE: THIS MAY BE CAUSED BY ICE ON THE SOLENOID CONTACTS."

CAUSE: THIS MAY BE CAUSED BY DUST AND/OR WATER INGRESS TO THE PRIMARY DRIVE BELT IDLER PULLEY BEARING."

INSTRUMENT CLUSTER: FAULTY GENERATOR FAULTY BATTERY MONITORING SYSTEM (BMS) THE CHARGE WARNING INDICATOR IS ILLUMINATED WHEN THE ENGINE IS RUNNING. CAUSE: THE POWER SUPPLY IS A FULLY INTEGRATED SYSTEM THAT REQUIRES SDD TO DIAGNOSE OVERALL FUNCTIONALITY ROBUSTLY TO MAKE SURE CUSTOMER SATISFACTION IS MET VIA RIGHT FIRST TIME DIAGNOSIS."

MODULE (PCM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE.

THOUGH THE TRANSMISSION CONTROL SWITCH HAS NOT BEEN MOVED. THE TRANSMISSION GEAR POSITION INDICATOR ON THE GEAR SELECTOR AND IN THE INSTRUMENT CLUSTER MESSAGE CENTER MAY BE FLASHING 'D' OR 'S'. IF THE ENGINE IS STOPPED AND RESTARTED AND THEN DRIVE (D) OR SPORT (S) IS SELECTED, VEHICLE OPERATION RETURNS TO NORMAL."

UPON DIAGNOSIS, THE TECHNICIAN MAY FIND ONE OR MORE DIAGNOSTIC TROUBLE C ODE (DTC ), LISTED IN THE TABLE BELOW AND RELEVANT TO THE HEATED OXYGEN SENSORS (HO2S), MAY BE STORED IN THE ENGINE CONTROL MODULE (ECM). CAUSE: THIS MAY BE CAUSED BY THERMAL SHOCK WHEN WATER CONTACTS THE HEATED SENSING ELEMENT."

(ECM) SOFTWARE IS REQUIRED ON THE MODELS, MODEL YEARS, ENGINE VARIANTS, AND VEHICLE IDENTIFICATION NUMBER (VIN) RANGES AS LISTED IN THE AFFECTED VEHICLE RANGE.

UPON DIAGNOSIS, THE TECHNICIAN MAY FIND ONE OR MORE DIAGNOSTIC TROUBLE CODE (DTC), LISTED IN THE TABLE BELOW AND RELEVANT TO THE HEATED OXYGEN SENSORS (HO2S), MAY BE STORED IN THE ENGINE CONTROL MODULE (ECM). CAUSE: THIS MAY BE CAUSED BY THERMAL SHOCK WHEN WATER CONTACTS THE HEATED SENSING ELEMENT."

DISCOVERY 4/LR4 (L319) AND RANGE ROVER SPORT (L320) ONLY. 10 MODEL YEAR ONWARDS. CAUSE: JLR ENGINEERING ARE CURRENTLY INVESTIGATING TO UNDERSTAND ANY SITUATIONS WHERE THE STEERING COLUMN IS THE CAUSE OF NOISE WHEN TURNING."

P0043, P0044, P0055, P0061, P0062, P0063, P0142, P0143, P0144, P0147, P0162, P0163, P0164, AND/OR P0167 - RELEVANT TO THE POST-CATALYST HEATED OXYGEN SENSORS - MAY BE STORED IN THE ENGINE CONTROL MODULE (ECM). CAUSE: THIS MAY BE CAUSED BY THERMAL SHOCK WHEN WATER CONTACTS THE HEATED SENSING ELEMENT."

A COOLANT LEAK IS FOUND FROM THE SEAM ON COOLANT PIPE (LR018275). SEE THE ATTACHED FILE FOR AN EXAMPLE OF THE LEAK LOCATION. CAUSE: A PROCESS ISSUE AT COMPONENT SUPPLIER."

P2183-00 BEING STORED IN THE ENGINE CONTROL MODULE (ECM). CAUSE: THIS MAY BE CAUSED BY A DIAGNOSTIC ROUTINE ERROR."

TO BE INSTALLED ON VEHICLES BUILT WITH THE PRIOR PART. CAUSE: THE VCT SOLENOID DESIGN CHANGED, AND THE ELECTRICAL CONNECTOR ON THE VCT SOLENOID IS A DIFFERENT SIZE."

ANALYSIS MANY ARE DEEMED AS NO FAULT FOUND. IT IS POSSIBLE DURING AN ECO STOP START THAT THE VEHICLE DOES NOT RE-START. CAUSE INCORRECT DIAGNOSIS"

DISPLAYED IN THE INSTRUMENT CLUSTER; ENGINE FAILS TO CRANK; VEHICLE MAY NOT UNLOCK / LOCK WHEN USING PASSIVE ENTRY OR WHEN PRESSING A SMART KEY BUTTON. CAUSE: THIS MAY BE CAUSED BY A 'LOCK UP' OF THE KEYLESS VEHICLE MODULE (KVM)."

OF TIME OR A LOW COOLANT LEVEL MESSAGE IS DISPLAYED IN THE MESSAGE CENTER. UPON INSPECTION, A LEAK MAY BE FOUND TO BE FROM THE FRONT OF THE ENGINE-DRIVEN COOLANT PUMP, TOGETHER WITH EXCESSIVE WEAR OF THE COOLANT PUMP BEARING."

THEREFORE WOULD APPRECIATE MORE INFORMATION TO AID INVESTIGATIONS. KNOWN ISSUES HAVE BEEN RESOLVED AND ASSURED VINS FOR EFFECTED MODELS ARE: EVOQUE: H021033(15MY), H920134 (PUNE) DISCOVERY 4 A756425 FREELANDER2: H432120, H911856 (PUNE)"

ACTION: PLEASE REFER TO THE PROCEDURE BELOW FOR INFORMATION ON HOW TO ACCESS THE NEW INFORMATION THROUGH SDD."

CAUSE: THIS MAY BE CAUSED BY EXCESSIVE FRONT SUSPENSION LOWER ARM REAR BUSH SNUBBER MOVEMENT."

THE NOISE MAY BE MORE NOTICEABLE WHEN THE ENGINE IS AT IDLE SPEED AND WHEN THE ENGINE IS COLD. CAUSE: THIS MAY BE CAUSED BY A NOISY HIGH PRESSURE FUEL PUMP OUTLET VALVE."

DISCOVERY 4/LR4 (L319) AND RANGE ROVER SPORT (L320) ONLY. 10 MODEL YEAR ONWARDS. CAUSE: JLR ENGINEERING ARE CURRENTLY INVESTIGATING TO UNDERSTAND ANY SITUATIONS WHERE THE STEERING COLUMN IS THE CAUSE OF NOISE WHEN TURNING.

A COOLANT LEAK IS FOUND FROM THE SEAM ON COOLANT PIPE (LR018275). SEE THE ATTACHED FILE FOR AN EXAMPLE OF THE LEAK LOCATION. CAUSE: A PROCESS ISSUE AT COMPONENT SUPPLIER."

CAUSE: THE TIMING CHAIN WAS NOT AT THE CORRECT TENSION. THIS WAS CAUSED BY THE FULL REPAIR PROCEDURE IN TSB LTB00474 NOT BEING FOLLOWED - A COMPLETE SET OF TIMING CHAIN TENSIONERS AND BLADES WERE NOT FITTED."

THE ENGINE CRANKS NORMALLY BUT WILL NOT START. CAUSE: THE ENGINE MAY HAVE BEEN FITTED WITH THE WRONG CAMSHAFT TIMING RINGS."

THE NOISE MAY BE MORE NOTICEABLE WHEN THE ENGINE IS AT IDLE SPEED AND WHEN THE ENGINE IS COLD. CAUSE: THIS MAY BE CAUSED BY A NOISY HIGH PRESSURE FUEL PUMP OUTLET VALVE."

ACTION: PLEASE REFER TO THE PROCEDURE BELOW FOR INFORMATION ON HOW TO ACCESS THE NEW INFORMATION THROUGH SDD."

UPON INSPECTION, LOW PRESSURE IS RECORDED ON THE HIGH PRESSURE SYSTEM, HIGH PRESSURE IS RECORDED ON THE LOW PRESSURE SYSTEM, AND THE COMPRESSOR CLUTCH (WHERE APPLICABLE) IS WORKING PROPERLY. CAUSE: THIS MAY BE CAUSED BY THE A/C COMPRESSOR DIRECT PRESSURE SENSING (DPS) VALVE BEING WORN."

DISCOVERY 4/LR4 (L319) AND RANGE ROVER SPORT (L320) ONLY. 10 MODEL YEAR ONWARDS. CAUSE: JLR ENGINEERING ARE CURRENTLY INVESTIGATING TO UNDERSTAND ANY SITUATIONS WHERE THE STEERING COLUMN IS THE CAUSE OF NOISE WHEN TURNING."

A COOLANT LEAK IS FOUND FROM THE SEAM ON COOLANT PIPE (LR018275). SEE THE ATTACHED FILE FOR AN EXAMPLE OF THE LEAK LOCATION. CAUSE: A PROCESS ISSUE AT COMPONENT SUPPLIER."

INDUCTION / FUEL INJECTION CLEANING EQUIPMENT OR MATERIALS. THIS INCLUDES, BUT IS NOT LIMITED TO, ""VACU-FLUSH"" TYPE EQUIPMENT. CAUSE: THE USE OF NON-APPROVED EQUIPMENT CAN CAUSE THE ENGINES TO HYDRO-LOCK, OR CAUSE OTHER ENGINE DAMAGE, AND SOMETIMES THE ONLY POSSIBLE REPAIR IS TO REPLACE THE ENGINE."

(15˚F / -10˚C OR LOWER) CONDITIONS, A 'TRANSMISSION FAULT' MESSAGE MAY BE DISPLAYED ON THE INSTRUMENT CLUSTER MESSAGE CENTER, AND DIAGNOSTIC TROUBLE CODE (DTC) P1707-77 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM). CAUSE: THIS MAY BE CAUSED BY TRANSMISSION OIL VISCOSITY AT COLD TEMPERATURES (15˚F / -10˚C AND LOWER) NOT ALLOWING THE TRANSMISSION OIL PUMP TO PRESSURIZE THE TRANSMISSION OIL TO RELEASE THE PARK PAWL."

P0043, P0044, P0055, P0061, P0062, P0063, P0142, P0143, P0144, P0147, P0162, P0163, P0164, AND/OR P0167]) RELEVANT TO THE POST-CATALYST HEATED OXYGEN SENSORS MAY BE STORED IN THE ENGINE CONTROL MODULE (ECM). CAUSE: THIS MAY BE CAUSED BY A POST-CATALYST HEATED OXYGEN SENSOR SOFTWARE ERROR."

THE START/ STOP IGNITION BUTTON IS PRESSED OR MAY RISE AND FALL IMMEDIATELY, PARTICULARLY WHERE AMBIENT TEMPERATURES ARE LESS THAN 4 DEGREES C. CAUSE: THE MOTOR WITHIN THE TRANSMISSION SELECTOR ASSEMBLY MAY BE AT THE LOWER END OF THE SPECIFICATION PREVENTING IT FROM RISING WITHIN THE REQUIRED TIME SPAN."

HIGHER TIME IN SERVICE VEHICLES, WHERE INSUFFICIENT PERFORMANCE OF THE AIR CONDITIONING COMPRESSOR HAS BEEN FOUND TO BE THE ROOT CAUSE OF THE ISSUE. COMPRESSOR PART NO. LR010723 & LR013934"

CAUSE: JLR ENGINEERING HAVE FOUND DURING THEIR INVESTIGATIONS THAT THE INSTRUMENT PANEL UPPER SECTION SPEAKER APERTURE BOLT MAY HAVE A RELAXED TORQUE (SEE TOPIX WORKSHOP MANUAL SECTION 76.46.04 FIG. E12471)"

CAUSE: THE TIMING CHAIN WAS NOT AT THE CORRECT TENSION. THIS WAS CAUSED BY THE FULL REPAIR PROCEDURE IN TSB LTB00474 NOT BEING FOLLOWED - A COMPLETE SET OF TIMING CHAIN TENSIONERS AND BLADES WERE NOT FITTED."

THICKNESS VARIATION (DTV) LEVELS ARE OUT OF SPECIFICATION CAUSING REPEATED PUSH BACKS ON THE BRAKE PISTONS/CALLIPERS."

OF TIME OR A LOW COOLANT LEVEL MESSAGE IS DISPLAYED IN THE MESSAGE CENTER. UPON INSPECTION, A LEAK MAY BE FOUND TO BE FROM THE FRONT OF THE ENGINE-DRIVEN COOLANT PUMP, TOGETHER WITH EXCESSIVE WEAR OF THE COOLANT PUMP BEARING."

RANGE ROVER VEHICLES WITHIN THE LISTED VIN RANGES WHERE THE CORRECT SPECIFICATION ENGINE OIL (5W-20) HAS BEEN WRONGLY MIXED WITH COLD-CLIMATE ENGINE OIL (0W-30). THIS INCORRECT MIXING MAY RESULT IN EMULSIFICATION OF THE ENGINE OIL, POTENTIALLY LEADING TO PERFORMANCE ISSUES WITH THE ENGINE LUBRICATION SYSTEMS."

WHERE THE CORRECT SPECIFICATION ENGINE OIL (5W-20) HAS BEEN WRONGLY MIXED WITH COLD-CLIMATE ENGINE OIL (0W-30). THIS INCORRECT MIXING MAY RESULT IN EMULSIFICATION OF THE ENGINE OIL, POTENTIALLY LEADING TO PERFORMANCE ISSUES WITH THE ENGINE LUBRICATION SYSTEMS. ACTION: RETAILERS ARE REQUIRED TO HOLD ALL AFFECTED VEHICLES WITHIN THE LISTED VIN RANGE THAT ARE IN THEIR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

DTC(S) RELEVANT TO A PURGE VALVE CONCERN STORED IN THE PCM. DTCS BELOW COULD POTENTIALLY INDICATE A CONCERN WITH THE PURGE VALVE. P0442 - SMALL LEAK P0444 - PURGE VALVE CIRCUIT OPEN P0456 - VERY SMALL LEAK P0458 - PURGE CONTROL VALVE CIRCUIT LOW P0459 - PURGE CONTROL VALVE CIRCUIT HIGH P0496 - EVAP SYSTEM HIGH PURGE FLOW P0497 - EVAP SYSTEM LOW PURGE FLOW SSM IS APPLICABLE TO THE FOLLOWING VEHICLES DISCOVERY 4/LR4 13MY ONWARDS FITTED WITH THE 5.0L NA ENGINE NEW RANGE ROVER (L405) ALL GASOLINE ENGINE DERIVATIVES NEW RANGE ROVER SPORT (L494) ALL GASOLINE ENGINE DERIVATIVES"

2F, P2405-00, P2406-00, P240A-00, P240B-00, P240C- 00, P2450-00 OR P2451-00 CAUSE: IF NO FAULT IS FOUND ON THE VEHICLE HAVING FOLLOWED THE LATEST DIAGNOSTIC GUIDANCE IN TOPIX, THE CAUSE MAY BE AN INTERNAL DMTL PUMP FAILURE."

ROVER / RANGE ROVER VEHICLES IN WARRANTY. CAUSE: UNKNOWN ENGINEERING INVESTIGATION ON-GOING."

ISSUE: LAND ROVER ARE CURRENTLY EVALUATING REPORTS WHERE DIAGNOSIS HAS LED TO A CONCERN WITH THE AIR SUSPENSION VALVE BLOCK ON DISCOVERY 4/ RANGE ROVER SPORT 10MY ONWARDS. CAUSE: CURRENTLY UNDER INVESTIGATION."

CAUSE: INCORRECT DIAGNOSIS ACTIONS: CONSIDER THE FOLLOWING IN THE FIRST INSTANCE WHEN INVESTIGATING WINDOW REGULATOR CONCERNS AND ITS OPERATION PRIOR TO REPLACING THE REGULATOR OR MOTOR: CUSTOMER MAY REPORT ONE OF THE FOLLOWING ISSUES:- A. WINDOW INOPERATIVE I.E. WILL NOT GO UP/DOWN, GOES UP/DOWN IN STAGES OR WILL NOT OPERATE AT ALL. B. WINDOW BOUNCE BACK OR NOT FULLY CLOSING. C. RATTLE OR NOISE DURING WINDOW OPERATION."

RANGE ROVER VEHICLES WITHIN THE LISTED VIN RANGES WHERE THE CORRECT SPECIFICATION ENGINE OIL (5W-20) HAS BEEN WRONGLY MIXED WITH COLD-CLIMATE ENGINE OIL (0W-30). THIS INCORRECT MIXING MAY RESULT IN EMULSIFICATION OF THE ENGINE OIL, POTENTIALLY LEADING TO PERFORMANCE ISSUES WITH THE ENGINE LUBRICATION SYSTEMS."

WHERE THE CORRECT SPECIFICATION ENGINE OIL (5W-20) HAS BEEN WRONGLY MIXED WITH COLD-CLIMATE ENGINE OIL (0W-30). THIS INCORRECT MIXING MAY RESULT IN EMULSIFICATION OF THE ENGINE OIL, POTENTIALLY LEADING TO PERFORMANCE ISSUES WITH THE ENGINE LUBRICATION SYSTEMS. ACTION: RETAILERS ARE REQUIRED TO HOLD ALL AFFECTED VEHICLES WITHIN THE LISTED VIN RANGE THAT ARE IN THEIR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

RISE WHEN THE ENGINE START/STOP BUTTON IS PRESSED (IGNITION SWITCHED 'ON'). REPEATED CYCLING OF THE ENGINE START/STOP BUTTON MAY TEMPORARILY OVERCOME THIS ISSUE. ACTION: RETAILERS ARE REQUIRED TO HOLD ALL AFFECTED VEHICLES WITHIN THE LISTED VIN RANGE THAT ARE IN THEIR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN"

HIGHER TIME IN SERVICE VEHICLES, WHERE INSUFFICIENT PERFORMANCE OF THE AIR CONDITIONING COMPRESSOR HAS BEEN FOUND TO BE THE ROOT CAUSE OF THE ISSUE. COMPRESSOR PART NO. LR010723 & LR013934 ACTION: THE COMPRESSOR SUPPLIER IN CONJUNCTION WITH LAND ROVER ENGINEERING HAVE MADE IMPROVEMENTS TO THE COMPRESSORS TO IMPROVE THEIR SERVICE LIFE AND RELIABILITY, AND TWO IMPROVED COMPRESSORS HAVE BEEN SUPPLIED TO PARTS OPERATIONS LR010723 SUPERSEDES TO LR056364 LR013934 SUPERSEDES TO LR056365 PLEASE ENSURE THAT THE LATER PART NUMBER IS FITTED TO ANY VEHICLE THAT IS SUFFERING FROM LACK OF COMPRESSOR PERFORMANCE."

CAUSE: LAND ROVER ENGINEERING HAVE RECENTLY VISITED DEALERSHIPS WHERE A REQUEST HAS BEEN MADE TO REPLACE THE STEERING GEAR FOR AN OIL LEAK IN THE AREA OF THE PINION HOUSING, CASTING, YOKE PLUG OR THE GAITER ADJACENT TO THE PINION HOUSING. FOLLOWING INVESTIGATION THE SOURCE OF THE LEAK PATH WAS IDENTIFIED AS BEING FROM THE SUPPLY AND RETURN HOSE O-RING SEALS. SEE ATTACHED DOCUMENT FOR EXAMPLES."

CUSTOMER EXPERIENCES THE ENGINE OVERHEATING. CAUSE: THE REFILL PROCEDURE HAS NOT BEEN COMPLETED CORRECTLY, RESULTING IN INSUFFICIENT COOLANT IN THE ENGINE."

CAUSE: WHEN CHARGING A BATTERY (BOTH PRIMARY AND SECONDARY) WITH A BMS (BATTERY MONITORING SYSTEM) FITTED, THE EARTH FROM THE CHARGER MUST BE CONNECTED TO A SUITABLE CHASSIS OR ENGINE EARTH (CHECK TOPIX FOR APPROPRIATE LOCATION). THIS ALLOWS THE BMS TO SEE THE CURRENT GOING INTO THE BATTERY. HOWEVER WHEN USING A DIAGNOSTIC CHARGER FROM MIDTRONICS SUCH AS GR1, GRX GR8(110 VOLTS)THIS CONNECTION PROCESS CAN CAUSE AN INCORRECT BATTERY ANALYSIS DUE TO THE EXTRA RESISTANCE IN THE WIRING WHEN CONNECTED TO A CHASSIS OR ENGINE EARTH."

CAUSE: LAND ROVER ENGINEERING HAVE RECENTLY VISITED DEALERSHIPS WHERE A REQUEST HAS BEEN MADE TO REPLACE THE STEERING GEAR FOR AN OIL LEAK IN THE AREA OF THE PINION HOUSING, CASTING, YOKE PLUG OR THE GAITER ADJACENT TO THE PINION HOUSING. FOLLOWING INVESTIGATION THE SOURCE OF THE LEAK PATH WAS IDENTIFIED AS BEING FROM THE SUPPLY AND RETURN HOSE O-RING SEALS."

THIS MAYBE ACCOMPANIED WITH THE COOLANT GAUGE READING HIGH AND/OR THE CHARGE WARNING INDICATOR ILLUMINATED. INVESTIGATION FINDS A CONCERN WITH THE PRIMARY IDLER PULLEY ASSEMBLY WHICH IN SOME CASES CAN LEAD TO DAMAGE OF THE PRIMARY DRIVE BELT. THE PRIMARY BELT DRIVES THE COOLANT PUMP AND GENERATOR HENCE THE POTENTIAL FOR THE COOLANT GAUGE TO READ HIGH AND/OR THE CHARGE WARNING INDICATOR ILLUMINATING IF THE BELT IS DAMAGED AND NOT FUNCTIONING CORRECTLY. THIS CONCERNS AFFECTS LTIS (LOW TIME IN SERVICE) VEHICLES WITH THE 3.0 AJ126 AND 5.0 AJ133 GASOLINE ENGINES FITTED.

that the Censole Fr ont and rear" Cooler box are not operating

AS A NATURAL PRODUCT AND THE CONDITIONS IT MAY CAUSE."

CAUSE: THIS MAY BE CAUSED BY THE MOLDING'S RETAINING CLIPS LOSING TENSION."

REAR* COOLER BOX ARE NOT OPERATING CAUSE CUSTOMER PERCEPTION"

CAUSE: DAMAGE/MARKING CAUSED BY OBJECT IMPACT AGAINST THE LENS. STAINING/DISCOLORATION CONTAMINATION CAUSED BY USING ANY TYPE OF CLEANING PRODUCT ON LENS."

USING THE IPOD / IPHONE USB CABLE ONLY, THE PLAYBACK SOUND MAY BE DISTORTED OR JUMPS/SKIPS. CAUSE: UNKNOWN, CURRENTLY UNDER INVESTIGATION."

USING THE IPOD/IPHONE USB CABLE ONLY, THE PLAYBACK SOUND MAY BE DISTORTED OR JUMPS/SKIPS. CAUSE: UNKNOWN, CURRENTLY UNDER INVESTIGATION."

range where the Central Junction Box (CJB) connector has incorrect pin assignments. The CJB connector has pin location ?1? wired in error where pin location ?44? should be wired. If a trailer wiring harness is installed, the trailer?s side and outer marker lamps do no illuminate.

identification please see Technical bulletin LTB00611 Tire pleassure Monitoring System Communication Frequency change. From Vin LA696287, L319 LW696287, L494, LG140911 L405 When a new service part TPMS sensor is not functioning immediately after fitment, IE no learning, failure of wheel sensor test, react as if they are stuck in shipping mode. Regardless of any driving cycle the parts will never go tinto the correct working mode.

inspected 101 warranty claims for Heated Oxygen Sensors (H2S) 23% were fkound to have no defects.

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

START UNAVAILABLE.

GATEWAY MODULE (GWM).

START UNAVAILABLE.

INTERMITTENT: - THE CURRENT VEHICLE POSITION DISPLAYED IS 'WASHINGTON D.C.' AND NOT THE ACTUAL CURRENT POSITION. ONCE A GPS SIGNAL IS ACQUIRED, THE CURRENT VEHICLE POSITION WILL THEN BE CORRECTLY DISPLAYED. - ROUTE GUIDANCE IS NOT AFFECTED DURING THIS INTERMITTENT FAULT MODE; IF THE ISSUE OCCURRED DURING ROUTE GUIDANCE, THE CURRENT ROUTE WILL CONTINUE TO BE DISPLAYED. B. PERMANENT: - THE CURRENT VEHICLE POSITION DISPLAYED IS 'WASHINGTON D.C.' AND NOT THE ACTUAL CURRENT POSITION. THE CURRENT VEHICLE POSITION WILL CONTINUE TO BE INCORRECTLY DISPLAYED AS 'WASHINGTON D.C.' FOLLOWING AN IGNITION CYCLE ('OFF' / 'ON'). - ROUTE GUIDANCE IS AFFECTED DURING THIS PERMANENT FAULT MODE; IF THE ISSUE OCCURRED DURING ROUTE GUIDANCE, THE CURRENT ROUTE WILL NOT RESUME AND THE DESTINATION WILL BE CANCELLED. - ALL PREVIOUS DESTINATIONS WILL BE DELETED (BUTTON 'GRAYED OUT'). CAUSE: THESE MAY BE CAUSED BY A SOFTWARE ISSUE OR HARD FAULT WITH THE INTEGRATED AUDIO MODULE (IAM). ACTION: SHOULD A CUSTOMER EXPRESS THIS CONCERN, FOLLOW APPROPRIATE SERVICE INSTRUCTION [A OR B] OUTLINED BELOW. A. INTERMITTENT: UPDATE THE INTEGRATED AUDIO MODULE (IAM) SOFTWARE. B. PERMANENT: REPLACE THE INTEGRATED AUDIO MODULE (IAM)."

INSTRUMENT CLUSTER FOR <1 SECOND (WHEN NO SERVICE IS REQUIRED). NO CUSTOMER SYMPTOMS UNTIL A SERVICE RESET HAS BEEN PERFORMED. WHEN AN ACTUAL SERVICE IS REQUIRED THE MESSAGE WILL APPEAR FOR 4 SECONDS AS DESIGN INTENT. CAUSE: DISTANCE TO NEXT SERVICE INITIALISATION VALUE MANAGEMENT BETWEEN ECM AND INSTRUMENT CLUSTER (FIRST 900MS)."

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE(TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE."

MODULE PART NUMBER OF: FK72-19H440 - AE; FK72-19H440 - BE; FK72-19H440 - AF; FK72-19H440 - BF SDD CANNOT COMMUNICATE WITH THE RFA. THIS WILL BE DISPLAYED AS A RED X FOR THE RFA IN THE SDD VEHICLE SPECIFICATION SCREEN."

ASSOCIATED COMPONENTS REPLACED FOR A NON-START CONDITION. FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORISED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

UPON DIAGNOSIS, THE TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES (DTC) B1D64-87 AND/OR B1D65-87 STORED IN THE HEADLAMP LEVELING CONTROL MODULE. CAUSE: THIS MAY BE CAUSED BY A SOFTWARE ERROR WITHIN THE HEADLAMP LEVELING CONTROL MODULE."

UPON DIAGNOSIS, THE TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES (DTC) B1D64-87 AND/OR B1D65-87 STORED IN THE HEADLAMP LEVELING CONTROL MODULE. CAUSE: THIS MAY BE CAUSED BY A SOFTWARE ERROR WITHIN THE HEADLAMP LEVELING CONTROL MODULE."

IF BLOCKAGE OCCURS WHILE ACC IS BEING USED, DRIVER INTERVENE AND/OR ""RADAR SENSOR BLOCKED"" MESSAGE WILL APPEAR ON THE CLUSTER AND DTC C1A67-97 SET. BLOCKAGE CAN ALSO OCCUR WHEN ACC IS NOT BEING USED. CAUSE: ""RADAR SENSOR BLOCKED"" INDICATES THAT THE ADAPTIVE SPEED CONTROL SYSTEM'S VISIBILITY HAS BEEN REDUCED DUE TO AN OBSTRUCTION. ACC CONTINUALLY SCANS FOR OBJECTS AHEAD AND, IF IT SEES NO OBJECTS I.E. VEHICLES, ROAD SIGNS, LAMP POSTS, GUARD RAILS ETC., IT WILL INDICATE A BLOCKAGE EVEN IF THE ACC IS NOT USED. THE C1A67-97 DTC FLAGS A RADAR BLOCKAGE SITUATION AND NOT A SYSTEM FAULT."

IF THE NAV BUTTON IS PRESSED A 2-5 SECOND PERIOD OF AM/ FM RADIO CAN BE HEARD AND THEN RETURNS BACK TO NO AUDIO. ISSUE WILL ONLY SELF-RECOVER AFTER AN IGNITION CYCLE. CAUSE: CURRENTLY UNDER ANALYSIS."

ASSOCIATED COMPONENTS REPLACED FOR A NON-START CONDITION. FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORISED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

CAUSE: POOR CONNECTION AT THE CAMERA MODULE."

IF A BCM HAS BEEN DETERMINED TO REQUIRE REPLACEMENT FOLLOWING DIAGNOSIS, PLEASE CARRY OUT THE STEPS LISTED IN THE ACTION BELOW. CAUSE: CURRENTLY UNDER ANALYSIS."

CAUSE: THIS MAY BE CAUSED BY POOR DTC LOGGING STRATEGY FOR GATEWAY MODULE B1479 73 DTC."

CAUSE: THIS MAY BE CAUSED BY POOR DTC LOGGING STRATEGY FOR GATEWAY MODULE B1479 73 DTC."

LINE DISPLAY FRONT (HLDF), MAY BE WRONGLY REPLACED WHEN TROUBLESHOOTING IF ISSUES ARE INCORRECTLY ATTRIBUTED TO IT. CAUSE: THE TS MAY BE INCORRECTLY DIAGNOSED AS THE SOURCE OF THE FAULT AND REPLACED IN ERROR."

23% WERE FOUND TO HAVE NO DEFECTS. CAUSE: ONE POSSIBLE REASON FOR THIS IS THAT ALL HO2S SENSORS ARE REPLACED WHEN ONLY ONE IS UNSERVICEABLE"

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE (TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE"

EVOQUE (L538), RANGE ROVER SPORT (L494), AND RANGE ROVER (L405) VEHICLES, FITTED WITH A DUAL BATTERY JUNCTION BOX (DBJB) AND AUXILIARY BATTERY ONLY, WHERE THE CHARGE WARNING INDICATOR REMAINS ILLUMINATED BUT THE VEHICLE CONTINUES TO DRIVE AS NORMAL. DIAGNOSTIC TROUBLE CODES (DTC) B1404-13 AND B1479-72 MAY BE STORED IN THE GATEWAY MODULE. THE ISSUE DISAPPEARS AFTER AN IGNITION CYCLE."

(L538), RANGE ROVER SPORT (L494), AND RANGE ROVER (L405) VEHICLES, FITTED WITH A DUAL BATTERY JUNCTION BOX (DBJB) AND AUXILIARY BATTERY ONLY, WHERE THE CHARGE WARNING INDICATOR REMAINS ILLUMINATED BUT THE VEHICLE CONTINUES TO DRIVE AS NORMAL. THE ISSUE DISAPPEARS AFTER AN IGNITION CYCLE. DIAGNOSTIC TROUBLE CODES (DTC) B1404-13 AND B1479-72 MAY BE STORED IN THE GATEWAY MODULE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

OFF OF POWER TO THE HEADLAMPS, INSTRUMENT CLUSTER, AND TOUCH SCREEN ALL AT THE SAME TIME ACCOMPANIED BY A ""CLICKING"" NOISE SPECIFICALLY FROM THE INTERIOR FUSE BOX LOCATION BY THE GLOVE BOX. ALL SYSTEMS OPERATE NORMALLY THEREAFTER WITHOUT ANY OTHER CUSTOMER SYMPTOMS OR FAULT CODES."

FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORISED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

THE ECO STOP/START MAY NOT FUNCTION. DIAGNOSTIC TROUBLE CODE (DTC) B1404-13 AND/OR B1479-72 WILL ALSO BE STORED IN THE GATEWAY MODULE (GWM). CAUSE: THIS MAY BE CAUSED BY A GATEWAY MODULE (GWM) SOFTWARE ISSUE."

CAUSE ALTERNATORS ARE BEING DAMAGED DUE TO CROSS POLARITY WHEN THE VEHICLE IS JUMP STARTED."

FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORIZED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD"

THIS CAN RESULT IN SDD REPORTING THAT THE RFA IS OFF BUS BY DISPLAYING A RED CROSS IN THE NETWORKS INTEGRITY SCREEN AND SDD NOT BEING ABLE TO RECOVER THE MODULE. CAUSE THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD OR A CORRUPTED SOFTWARE DOWNLOAD FILE."

PDIS AND THEN RETURNING THE VEHICLE TO A STORAGE COMPOUND WITHOUT REFITTING THE TRANSIT RELAY OR RETURNING THE VEHICLE TO TRANSIT MODE. TRANSIT MODE / TRANSIT RELAY ARE DESIGNED TO PROTECT THE CUSTOMERS BATTERY UP TO THE POINT OF DELIVERY. ALL VEHICLES IN STORAGE MUST HAVE THE TRANSIT RELAY IN PLACE OR BE IN TRANSIT MODE."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD."

THE LISTED VIN RANGE WHERE THE CENTRAL JUNCTION BOX (CJB) CONNECTOR HAS INCORRECT PIN ASSIGNMENTS. THE CJB CONNECTOR HAS PIN LOCATION 1 WIRED IN ERROR WHERE PIN LOCATION 44 SHOULD BE WIRED. IF A TRAILER WIRING HARNESS IS INSTALLED, THE TRAILERS SIDE AND OUTER MARKER LAMPS DO NO ILLUMINATE."

VIN RANGE WHERE THE CENTRAL JUNCTION BOX (CJB) CONNECTOR HAS INCORRECT PIN ASSIGNMENTS. THE CJB CONNECTOR HAS PIN LOCATION 1 WIRED IN ERROR WHERE PIN LOCATION 44 SHOULD BE WIRED. IF A TRAILER WIRING HARNESS IS INSTALLED, THE TRAILERS SIDE AND OUTER MARKER LAMPS DO NO ILLUMINATE. ACTION: RETAILERS ARE REQUIRED TO HOLD ALL AFFECTED VEHICLES WITHIN THE LISTED VIN RANGE THAT ARE IN THEIR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

LISTED VIN RANGES WHERE THE CENTRAL JUNCTION BOX (CJB) CONNECTOR HAS INCORRECT PIN ASSIGNMENTS. THE CONNECTOR HAS PIN LOCATION 1 WIRED IN ERROR WHERE PIN LOCATION 44 SHOULD BE WIRED. IF A TRAILER WIRING HARNESS IS INSTALLED, THE TRAILERS SIDE AND OUTER MARKER LAMPS DO NO ILLUMINATE."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD."

(DTC) B11DB-87 STORED IN THE BODY CONTROL MODULE (BCM). CAUSE: THIS MAY BE CAUSED BY A BLOWN BATTERY MONITORING SYSTEM (BMS) FUSED HARNESS."

A. INTERMITTENT: - THE CURRENT VEHICLE POSITION DISPLAYED IS 'WASHINGTON D.C.' AND NOT THE ACTUAL CURRENT POSITION. ONCE A GPS SIGNAL IS ACQUIRED, THE CURRENT VEHICLE POSITION WILL THEN BE CORRECTLY DISPLAYED. - ROUTE GUIDANCE IS NOT AFFECTED DURING THIS INTERMITTENT FAULT MODE; IF THE ISSUE OCCURRED DURING ROUTE GUIDANCE, THE CURRENT ROUTE WILL CONTINUE TO BE DISPLAYED. B. PERMANENT: - THE CURRENT VEHICLE POSITION DISPLAYED IS 'WASHINGTON D.C.' AND NOT THE ACTUAL CURRENT POSITION. THE CURRENT VEHICLE POSITION WILL CONTINUE TO BE INCORRECTLY DISPLAYED AS 'WASHINGTON D.C.' FOLLOWING AN IGNITION CYCLE ('OFF' / 'ON'). - ROUTE GUIDANCE IS AFFECTED DURING THIS PERMANENT FAULT MODE; IF THE ISSUE OCCURRED DURING ROUTE GUIDANCE, THE CURRENT ROUTE WILL NOT RESUME AND THE DESTINATION WILL BE CANCELLED. - ALL PREVIOUS DESTINATIONS WILL BE DELETED (BUTTON 'GRAYED OUT')."

CAUSE: IF THE BATTERY NEGATIVE TERMINAL CLAMP BOLT IS NOT PARALLEL WITH THE LONGITUDINAL SIDE OF THE BATTERY IT MAY CAUSE DIFFICULTIES WHEN TRYING TO FIT THE BATTERY BOX LID. ADDITIONALLY THE CLAMP ALSO NEEDS TO BE FITTED AS LOW AS POSSIBLE ON THE NEGATIVE TERMINAL TO AID FITMENT."

NO LEARNING, FAILURE OF WHEEL SENSOR TEST, REACT AS IF THEY ARE STUCK IN SHIPPING MODE. REGARDLESS OF ANY DRIVING CYCLE THE PARTS WILL NEVER GO INTO THE CORRECT WORKING MODE. CAUSE: SERVICE PARTS HAVE BEEN DELIVERED IN THE ""WRONG MODE""."

THE AUDIO/VIDEO BUTTON ON TOUCH-SCREEN HOME PAGE MAY ALSO BE GREYED OUT. CAUSE: ONE OF THE MODULES SITUATED ON THE MOST BUS, SUCH AS AUDIO AMPLIFIER MODULE OR AUDIO CONTROL MODULE, HAVE A SOFTWARE CONFLICT."

THE VEHICLE SEAT MEMORY MODULE LOGS U1A4C 00, BUILD END OF LINE MODE ACTIVE CAUSE THE SEAT MODULE HAS BEEN INCORRECTLY CONFIGURED TO THE VEHICLE."

FAULT CODES STARTING WITH C1A ESPECIALLY C1A36-01 LOGGED. POSSIBILITY THAT ADDITIONAL WARNING LIGHTS MAY BE DISPLAYED AND ADDITIONAL FAULT CODES STORED. CAUSE THE HARNESS HAS BEEN INCORRECTLY ROUTED AND IS PRESSING AGAINST THE WASHER FILLER TUBE CAUSING INSULATION DAMAGE AND A SHORT CIRCUIT/OPEN CIRCUIT"

WHEN THE KEY HANDSET REMOTE IS OPERATED. CAUSE: CURRENTLY UNDER ANALYSIS."

MODEL 2014-15 RANGE ROVER EVOQUE, LR4. *PE UPDATED 6/26/15. *PE

AND DISPLAYS, INTERMITTENTLY, BATTERY WARNING MESSAGE AND WARNING LAMP. MODEL 2014 LR4 (LA). *PE

SHOULD BE WIRED, CAUSING TRAILER'S SIDE AND OUTER MARKER LAMPS, IF WIRING HARNESS IS INSTALLED, NOT TO ILLUMINATE. MODEL 2014 LR4 (L319). *PE

CENTRAL JUNCTION BOX (CJB), CAUSES SIDE AND OUTER MARKER LAMPS NOT TO ILLUMINATE ON TRAILER, IF TRAILER WIRING HARNESS IS INSTALLED. MODEL LR4. *PE

shift the vehicle out of the park position. DTC P1707-72 is found to be stored in the TCM (Transportation Control Modulef)

exhibit intermittent operation, causing one or more of the following issues: ? Audio volume does not adjust (up and/or down)? Radio 'seek' buttons do not operate ? Volume control buttons cause the radio station to change ? InControl system slow to operate (blank screen followed by the 'Land Rover' logo) ? Transmission paddle shifters do not operate ? Diagnostic Trouble Codes (DTC) U2013-02 and/or B1D21-13 stored

UPON INSPECTION, LOW PRESSURE IS RECORDED ON THE HIGH PRESSURE SYSTEM, HIGH PRESSURE IS RECORDED ON THE LOW PRESSURE SYSTEM, AND THE COMPRESSOR CLUTCH (WHERE APPLICABLE) IS WORKING PROPERLY.

INSTRUMENT PACK WITH ASSOCIATED DTC'S FOR BRAKE LIGHT SWITCH (P0504-27, P0504-62, C1A96-64) OR BRAKES SHOWING SIGNS OF DRAG AND BINDING. CAUSE: INCORRECT BRAKE LIGHT SWITCH SETTING. NOTE: ANALYSIS OF RETURNED BRAKE SWITCHES HAVE SHOWN NO ISSUES WITH THE BRAKE SWITCH ITSELF. DO NOT REPLACE THE SWITCH BEFORE ADJUSTMENT IS CARRIED OUT."

FIXED GEAR 'LIMP HOME' OPERATION. UPON DIAGNOSIS, A TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE (DTC) P0780-93 STORED IN THE TRANSMISSION CONTROL MODULE (TCM). CAUSE: THIS MAY BE CAUSED BY AN ERROR IN THE TCM SOFTWARE."

CRUISE CONTROL) AND TRANSMISSION PADDLE SWITCHES MAY EXHIBIT INTERMITTENT OPERATION, CAUSING ONE OR MORE (LIST NOT EXHAUSTIVE) OF THE FOLLOWING ISSUES: AUDIO VOLUME WILL NOT ADJUST (UP AND/OR DOWN) RADIO SEEK BUTTONS WILL NOT OPERATE VOLUME CONTROL BUTTONS CAUSE THE RADIO STATION TO CHANGE THE INFOTAINMENT SYSTEM IS SLOW TO OPERATE (BLANK SCREEN FOLLOWED BY THE 'LAND ROVER' LOGO) DIAGNOSTIC TROUBLE CODE (DTC) U2013-02 'SWITCH PACK, GENERAL SIGNAL FAILURE' IS STORED IN THE INSTRUMENT CLUSTER MEMORY DTC B1D21-13 'REMOTE CONTROL SWITCH CIRCUIT OPEN' IS STORED IN THE TOUCH SCREEN MEMORY TRANSMISSION PADDLE SWITCHES INOPERATIVE OR INTERMITTENT FUNCTIONALITY CRUISE CONTROL INOPERATIVE"

CAUSE: THIS MAY BE CAUSED BY A TOUCH SCREEN SOFTWARE ISSUE."

CAUSE: THIS MAY BE CAUSED BY A CRACKED TRANSMISSION HEAT SHIELD MOUNTING BRACKET."

RANGE ROVER (L405) VEHICLES WHERE THE TRANSMISSION FILTER MAY BECOME DETACHED FROM THE TRANSMISSION FLUID PAN. THIS COULD RESULT IN HARSH SHIFTING OF THE TRANSMISSION AND A TRANSMISSION FAULT MESSAGE MAYBE DISPLAYED ON THE INSTRUMENT CLUSTER MESSAGE CENTER."

SITUATION: AN ISSUE HAS BEEN IDENTIFIED ON A NUMBER OF 2014 MODEL YEAR LR4 (L319), RANGE ROVER SPORT (L494), AND RANGE ROVER (L405) VEHICLES WHERE THE TRANSMISSION FILTER MAY BECOME DETACHED FROM THE TRANSMISSION FLUID PAN. THIS COULD RESULT IN HARSH SHIFTING OF THE TRANSMISSION AND A TRANSMISSION FAULT MESSAGE MAYBE DISPLAYED ON THE INSTRUMENT CLUSTER MESSAGE CENTER. ACTION: RETAILERS ARE REQUIRED TO HOLD ALL AFFECTED VEHICLES (SEE SERVICE BULLETIN SGI14-25 FOR SPECIFIC AFFECTED VINS) THAT ARE IN THEIR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN."

DTC P1707-72 IS FOUND TO BE STORED IN THE TCM (TRANSMISSION CONTROL MODULE). CAUSE: EPRL (EMERGENCY PARK RELEASE LEVER) NOT LOCKED DOWN FROM PDI."

CAUSE: OIL OR GREASE LEAK PAST INPUT SHAFT SEAL THROUGH NORMAL USE OR SEAL FAILURE."

TO RISE OR INITIALLY RISES BEFORE LOWERING ITSELF BACK TO ITS DEFAULT POSITION FOR AN IGNITION OFF STATE, WHICH IS CONFIRMED BY DTC P176B - 71 (TRANSMISSION RANGE SELECTOR UP AND DOWN POSITION CONTROL ERROR) CAUSE: POTENTIAL OF A MIXED STOCK CONDITION"

THE RED LIGHTS ON THE TCS OPERATE AS NORMAL.

SELECTED IN COLD CONDITIONS (15F/10C OR LOWER) WOULD EXPERIENCE NO DRIVE. *LJ

AN ISSUE WITH STEERING OR STEERING GEARS. MODEL LR4 (L319), LR2 (L359), RANGE ROVER SPORT (L320). *PE

Range Roiver badge.

the Instrument Pack even though the Hood/Bonnet is closed.

bulging.

VARIOUS CONDITIONS THAT CONTRIBUTE TO THE OPERATION OF THE WINDOW REGULATOR NOT OPERATING"

CAUSE: THIS MAY BE CAUSED BY A TOLERANCE STACK-UP BETWEEN THE DOOR MIRROR AND THE DOOR AND/OR THE RETAINING SCREWS MAY BE LOOSE/UNDER TORQUED."

WHICH DEMONSTRATES THE ISSUE.

CAUSE: THIS MAY BE CAUSED BY A TOLERANCE STACK-UP BETWEEN THE DOOR MIRROR AND THE DOOR AND/OR THE RETAINING SCREWS MAY BE LOOSE/UNDER TORQUED."

CAUSE: THIS MAY BE CAUSED BY A BUILD-UP OF DIRT AND GREASE ON THE SURFACE OF THE WINDSHIELD GLASS."

CAUSE. THE WIRES TO THE SWITCH HAVE CORRODED AND ARE POSSIBLY BROKEN."

CAUSE: THIS MAY BE CAUSED BY THE HANDSET MANUFACTURING PROCESS."

CAUSE. THE WIRES TO THE SWITCH HAVE CORRODED AND ARE POSSIBLY BROKEN."

CLADDING IS COMING ADRIFT/LOOSE OR A GAP IS EVIDENT.THE ATTACHED FILE SHOWS EXAMPLES. CAUSE UNDER INVESTIGATION"

CAUSE: THIS MAY BE CAUSED BY A TOLERANCE STACK-UP BETWEEN THE DOOR MIRROR AND THE DOOR."

CAUSE THE ROOT CAUSE WAS FOUND TO BE THAT ANTI RUST OIL RESIDUE REMAINS ON THE SUPPLIER'S TOOLING AT THE START OF A PRODUCTION RUN."

BULGING.

*PE

Display in the Instrument Cluster Message Center does not correctly match the actual terrain mode which has been selected. A customer may state their Terrain Optimisation display in the Instrument Cluster Message Center does not correctly match the actual terrain mode which has been selected. Also the text in the Instrument Cluster Message Center , for the selected terrain mode, does not display correctly., BMP_TR_VEHICLE is displayed instead of the correct corresponding text for the selected terrain mode.

stations drop in and out on a regular basis.

IN ADDITION THE CURRENT VEHICLE LOCATION INDICATOR WILL NOT LOCK ONTO THE CORRECT LOCATION ON THE MAP. CAUSE: SOFTWARE ERROR."

CAUSE: THIS MAY BE CAUSED BY AN INSTRUMENT CLUSTER SOFTWARE ERROR."

CAUSE THERE IS A POTENTIAL THAT THE TOP WINDSCREEN SEAL HAS BECOME DISLODGED OVER TIME CAUSING A WINDNOISE"

DIAGNOSTIC TROUBLE CODES (DTC) ARE STORED. CAUSE: THIS MAY BE CAUSED BY VARIOUS ISSUES."

WHICH IS NOT COMPATIBLE WITH LAND ROVER INFOTAINMENT SYSTEMS. CAUSE THIS IS TO MAKE YOU AWARE OF THE TYPES OF MEDIA THAT MAY CAUSE THE UNIT TO FAIL WITH THE CUSTOMER."

'HOOD OPEN' MESSAGE IS DISPLAYED ON THE INSTRUMENT CLUSTER; AND/OR A MISLOCK SOUND IS EMITTED WHEN LOCKING THE VEHICLE. CAUSE: THESE ISSUES MAY BE CAUSED BY A FAULTY HOOD OPEN SWITCH."

WHICH IS NOT COMPATIBLE WITH LAND ROVER INFOTAINMENT SYSTEMS. CAUSE THIS IS TO MAKE YOU AWARE OF THE TYPES OF MEDIA THAT MAY CAUSE THE UNIT TO FAIL WITH THE CUSTOMER. THEY ARE COPY CONTROL COMPACT DISCS (CCCD) RECORDABLE COMPACT DISCS (CD-R) REWRITABLE COMPACT DISCS (CD-RW) ECO DISCS, WHICH ARE VERY THIN, ONLY 0.6MM. PLEASE REFER TO ATTACHMENT FOR EXAMPLES OF DISCS THAT ARE KNOWN TO HAVE CAUSED DAMAGE."

CAUSE: SOFTWARE COMPATIBILITY ISSUES"

CAUSE: SOFTWARE COMPATIBILITY ISSUES"

ONLY), THE CAMERA IMAGE MAY BE LOST AND A BLUE SCREEN IS DISPLAYED CAUSE: THIS MAY BE CAUSED BY SIGNAL LOSS THROUGH THE COAX."

CAUSE: INCORRECT DIAGNOSIS."

Range Rover Sport and Discovery 4/LR4, 14 and 15 Model Year oinly.

WITH A WHEEL SPEED SENSOR ONLY.

CAUSE BRAKE LIGHT SWITCH / BRAKE PEDAL SHIM INTERACTION. NOTE: NOT ALL VEHICLES WILL BE FITTED WITH BRAKE PEDAL SHIM."

CAUSE: DAMAGE TO THE CALIPER FINISH WHILE CLEANING THE VEHICLE AND, OR THE ROAD WHEELS"

THIS WILL OCCUR WITHOUT THE BRAKE PEDAL BEING PRESSED AND SETTING OFF FROM STATIONARY / DRIVING AT LOW SPEEDS. CAUSE: THE ACTION OF THE BIAS SPRING WITHIN THE REAR BRAKE SHOE MECHANISM WHEN COMBINED WITH INCORRECT ADJUSTMENT OR WEAR OF THE SYSTEM."

VEHICLES WITH STANDARD BRAKES ONLY. CAUSE: BRAKE COMPRESSIBILITY OF THE PAD, WHILST WITHIN SPECIFICATION, MAY BE SLIGHTLY INCOMPATIBLE WITH THE DRIVING STYLE AND VEHICLE USAGE PATTERNS OF A SMALL NUMBER OF CUSTOMERS. WHILTST THERE IS NO IMPACT ON THE EFFICIENCY OF THE BRAKING SYSTEM, IN SOME CIRCUMSTANCES THIS MAY LEAD TO NOISE BECOMING APPARENT."

RANGE ROVER, RANGE ROVER SPORT AND DISCOVERY 4/LR4. 14 AND 15 MODEL YEAR ONLY. CAUSE: CURRENTLY UNDER INVESTIGATION"

CAUSE: ASSEMBLY GREASE/FLUID IS PRESENT FROM THE MANUFACTURING PROCESS AND GIVES A SIMILAR APPEARANCE TO A BRAKE FLUID LEAK."

CAUSE: ASSEMBLY GREASE/ FLUID IS PRESENT FROM THE MANUFACTURING PROCESS AND GIVES A SIMILAR APPEARANCE TO A BRAKE FLUID LEAK."

CAUSE: THIS MAY BE CAUSED BY THE CONTACTS IN THE HORN PAD."

*LJ

- A custoimer may report a noise when turning the steering wheel, which is confirmed by the dealer as originating from the steering column. Discovery 4/LR4 (Llr4) and Range Rover Sport (L320) 10 Model year onwards

CAUSE: UNDER INVESTIGATION"

ACTION: WHEN DIAGNOSING CUSTOMER CONCERNS RELATING TO THE HYDRAULIC POWER STEERING SYSTEM, REFER TO THE SERVICE INFORMATION BELOW."

THE ISSUE IS COMMON ACROSS ALL MANUFACTURERS SYMPTOMS WHEN THE APPLE DEVICE IS CONNECTED TO THE CAR SYSTEM AND A CALL IS RECEIVED THERE IS NO OPTION TO ANSWER OR REJECT THE INCOMING CALL ON THE SYSTEM. THE STEERING WHEEL CONTROLS ALSO HAVE NO EFFECT. THE TOUCH SCREEN CONTINUES TO DISPLAY THE PHONE SCREEN. THE POP-UP SCREEN TO ANSWER OR REJECT THE CALL IS NOT SHOWN."

CAUSE: THIS MAY BE CAUSED BY INCORRECT CALIBRATION OF THE STEERING COLUMN DURING THE PRODUCTION PROCESS."

FLAT SPOTS ON THE ROLLING SURFACE OF THE TIRE. CAUSE: TEMPORARY FLAT SPOTS NATURALLY DEVELOP ON THE ROLLING SURFACE OF A TIRE WHEN THE WHEELS OF THE VEHICLE ARE STATIONARY OVER A PERIOD OF TIME."

CAUSE: THIS MAY BE CAUSED BY A ROAD WHEEL/TIRE ASSEMBLY IMBALANCE AND/OR TEMPORARY TIRE FLAT-SPOTTING.

Dealer Data Update

Dealer Data Update

Dealer Data Update

Dealer Data Update

THIS CAN CAUSE THE ALARM TO TRIGGER OR THE VEHICLE TO NOT LOCK.

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES"

CAUSE: DAMAGE/MARKING CAUSED BY OBJECT IMPACT AGAINST THE LENS. STAINING/DISCOLORATION CONTAMINATION CAUSED BY USING ANY TYPE OF CLEANING PRODUCT ON LENS. IMPORTANT: OWNERS HANDBOOK SPECIFIES TO CLEAN WITH A LIGHTLY MOISTENED CLOTH AND DO NOT USE CHEMICAL AGENTS OR DOMESTIC CLEANERS ACTION WHERE A CUSTOMER CONCERN IS REPORTED, PLEASE ORDER THE LENS KIT FOR THE RELEVANT MODEL"

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OUTSIDE OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE PERFORMANCE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES."

CAUSE: THIS MAY BE CAUSED BY THE DESIGN OF THE TAIL LAMP ASSEMBLY ALLOWING MOISTURE TO SETTLE ON THE INSIDE OF THE LAMP LENS."

CAUSE: THIS IS EITHER CAUSED BY THE SHIPPING PROCESS AND SHOULD BE CLAIMED THROUGH TRANSPORT / DISTRIBUTION OR IT IS CAUSED DURING JLR MANUFACTURING PROCESSES AND SHOULD BE CLAIMED AS PER WARRANTY POLICY."

DIFFICULT TO OPERATE (DOES NOT FOLD OR 'STICKS' WHEN OPERATING). CAUSE: THIS MAY BE CAUSED BY THE SEAT OPERATING LEVER BEING OUT OF ALIGNMENT."

sticking rotary dials

AND MATERIALS ACROSS THE VEHICLE INTERIOR THAT HAVE MADE CONTACT WITH THE ICP AND OR ROTARY DIALS."

CAUSE: THIS MAY BE CAUSED BY MOLD SPORE ACCUMULATION / BUILD-UP IN THE FRONT EVAPORATOR CORE."

When the returned components are tested they are found to have no faults.

INSTRUMENT PACK EVEN THOUGH THE HOOD / BONNET IS CLOSED CAUSE: THERE IS A POTENTIAL THAT AN INTERNAL SPRING COULD BECOME DISLODGED"

CAUSE: REAR WHEEL BEARING NOISY OR DIFFICULT TO TURN."

(SEE FIG.1) ACTION: REPLACE BY PRESSING ON NEW BUTTON CAP PART NO: LR045801 (SEE FIG.2)"

(blowing warm and then cold); ? Windshield, rear window, and/or door windows mist up in cool (15C or lower) ambient temperatures; ? Poor cooling performance of the Air Conditioning (A/C) system; and/or ? Warm, damp or musty smells coming from the vents.

EXPECTATION.