2010 Land Rover LR4 TSBs

DISPLAYED IN THE INSTRUMENT CLUSTER; ENGINE FAILS TO CRANK; VEHICLE MAY NOT UNLOCK / LOCK WHEN USING PASSIVE ENTRY OR WHEN PRESSING A SMART KEY BUTTON.

TYRE PRESSURE MONITORING SYSTEM (TPMS) WARNING MESSAGES. CUSTOMERS AND RETAILERS HAVE BEEN UNABLE TO RE-INFLATE AND MAINTAIN SERVICE PRESSURES DUE TO LEAKAGE FROM THE TPMS VALVES. ISSUE MAY AFFECT: 15MY AND 16MY RANGE ROVER EVOQUE, DISCOVERY SPORT, RANGE ROVER (ALL NEW), DISCOVERY 4/LR4, RANGE ROVER SPORT VEHICLES. CAUSE: RETAILER TECHNICIANS HAVE OBSERVED TPMS VALVES WHERE THERE IS EVIDENCE OF AIR LOSS OR LEAKAGE FROM THE BASE OF THE VALVE STEM OR THROUGH THE TPMS VALVE CORE ."

CAUSE: THIS MAY BE CAUSED BY DUST AND/OR WATER INGRESS TO THE ACCESSORY DRIVE BELT IDLER PULLEY BEARING."

RESTARTS IN XXX MILES, DIESEL EXHAUST FLUID DOSING MALFUNCTION WARNING MESSAGE DISPLAYED WITHIN THE INSTRUMENT CLUSTER MESSAGE CENTER AND DTCS P208B-00/P2BAE-00/P2BAF-00 STORED IN THE PCM (POWERTRAIN CONTROL MODULE) CAUSE: AIR IN THE SYSTEM."

CUSTOMERS OR EXTERNAL INFLUENCES SUCH AS CAR WASHES MAY INADVERTANTLY KNOCK THE DOOR MIRROR HEAD INTO THE FOLDED POSITION, THIS WILL THEN CAUSE THE MIRROR HEAD TO BE LOOSE"

CAUSE: THIS MAY BE CAUSED BY DUST AND/OR WATER INGRESS TO THE PRIMARY DRIVE BELT IDLER PULLEY BEARING."

INSTRUMENT CLUSTER: FAULTY GENERATOR FAULTY BATTERY MONITORING SYSTEM (BMS) THE CHARGE WARNING INDICATOR IS ILLUMINATED WHEN THE ENGINE IS RUNNING. CAUSE: THE POWER SUPPLY IS A FULLY INTEGRATED SYSTEM THAT REQUIRES SDD TO DIAGNOSE OVERALL FUNCTIONALITY ROBUSTLY TO MAKE SURE CUSTOMER SATISFACTION IS MET VIA RIGHT FIRST TIME DIAGNOSIS."

DISCOVERY 4/LR4 (L319) AND RANGE ROVER SPORT (L320) ONLY. 10 MODEL YEAR ONWARDS. CAUSE: JLR ENGINEERING ARE CURRENTLY INVESTIGATING TO UNDERSTAND ANY SITUATIONS WHERE THE STEERING COLUMN IS THE CAUSE OF NOISE WHEN TURNING."

A COOLANT LEAK IS FOUND FROM THE SEAM ON COOLANT PIPE (LR018275). SEE THE ATTACHED FILE FOR AN EXAMPLE OF THE LEAK LOCATION. CAUSE: A PROCESS ISSUE AT COMPONENT SUPPLIER."

P2183-00 BEING STORED IN THE ENGINE CONTROL MODULE (ECM). CAUSE: THIS MAY BE CAUSED BY A DIAGNOSTIC ROUTINE ERROR."

TO BE INSTALLED ON VEHICLES BUILT WITH THE PRIOR PART. CAUSE: THE VCT SOLENOID DESIGN CHANGED, AND THE ELECTRICAL CONNECTOR ON THE VCT SOLENOID IS A DIFFERENT SIZE."

DISPLAYED IN THE INSTRUMENT CLUSTER; ENGINE FAILS TO CRANK; VEHICLE MAY NOT UNLOCK / LOCK WHEN USING PASSIVE ENTRY OR WHEN PRESSING A SMART KEY BUTTON. CAUSE: THIS MAY BE CAUSED BY A 'LOCK UP' OF THE KEYLESS VEHICLE MODULE (KVM)."

THE NOISE MAY BE MORE PRONOUNCED WHEN THE ENGINE IS AT IDLE SPEED. CAUSE: THIS MAY BE CAUSED BY WEAR ON THE TIMING CHAIN LEVER, RESULTING IN REDUCED TENSION ON THE TIMING CHAIN."

OF TIME OR A LOW COOLANT LEVEL MESSAGE IS DISPLAYED IN THE MESSAGE CENTER. UPON INSPECTION, A LEAK MAY BE FOUND TO BE FROM THE FRONT OF THE ENGINE-DRIVEN COOLANT PUMP, TOGETHER WITH EXCESSIVE WEAR OF THE COOLANT PUMP BEARING."

THEREFORE WOULD APPRECIATE MORE INFORMATION TO AID INVESTIGATIONS. KNOWN ISSUES HAVE BEEN RESOLVED AND ASSURED VINS FOR EFFECTED MODELS ARE: EVOQUE: H021033(15MY), H920134 (PUNE) DISCOVERY 4 A756425 FREELANDER2: H432120, H911856 (PUNE)"

ACTION: PLEASE REFER TO THE PROCEDURE BELOW FOR INFORMATION ON HOW TO ACCESS THE NEW INFORMATION THROUGH SDD."

CAUSE: THIS MAY BE CAUSED BY EXCESSIVE FRONT SUSPENSION LOWER ARM REAR BUSH SNUBBER MOVEMENT."

DISCOVERY 4/LR4 (L319) AND RANGE ROVER SPORT (L320) ONLY. 10 MODEL YEAR ONWARDS. CAUSE: JLR ENGINEERING ARE CURRENTLY INVESTIGATING TO UNDERSTAND ANY SITUATIONS WHERE THE STEERING COLUMN IS THE CAUSE OF NOISE WHEN TURNING.

A COOLANT LEAK IS FOUND FROM THE SEAM ON COOLANT PIPE (LR018275). SEE THE ATTACHED FILE FOR AN EXAMPLE OF THE LEAK LOCATION. CAUSE: A PROCESS ISSUE AT COMPONENT SUPPLIER."

CAUSE: THE TIMING CHAIN WAS NOT AT THE CORRECT TENSION. THIS WAS CAUSED BY THE FULL REPAIR PROCEDURE IN TSB LTB00474 NOT BEING FOLLOWED - A COMPLETE SET OF TIMING CHAIN TENSIONERS AND BLADES WERE NOT FITTED."

THE ENGINE CRANKS NORMALLY BUT WILL NOT START. CAUSE: THE ENGINE MAY HAVE BEEN FITTED WITH THE WRONG CAMSHAFT TIMING RINGS."

ACTION: PLEASE REFER TO THE PROCEDURE BELOW FOR INFORMATION ON HOW TO ACCESS THE NEW INFORMATION THROUGH SDD."

UPON INSPECTION, LOW PRESSURE IS RECORDED ON THE HIGH PRESSURE SYSTEM, HIGH PRESSURE IS RECORDED ON THE LOW PRESSURE SYSTEM, AND THE COMPRESSOR CLUTCH (WHERE APPLICABLE) IS WORKING PROPERLY. CAUSE: THIS MAY BE CAUSED BY THE A/C COMPRESSOR DIRECT PRESSURE SENSING (DPS) VALVE BEING WORN."

DISCOVERY 4/LR4 (L319) AND RANGE ROVER SPORT (L320) ONLY. 10 MODEL YEAR ONWARDS. CAUSE: JLR ENGINEERING ARE CURRENTLY INVESTIGATING TO UNDERSTAND ANY SITUATIONS WHERE THE STEERING COLUMN IS THE CAUSE OF NOISE WHEN TURNING."

A COOLANT LEAK IS FOUND FROM THE SEAM ON COOLANT PIPE (LR018275). SEE THE ATTACHED FILE FOR AN EXAMPLE OF THE LEAK LOCATION. CAUSE: A PROCESS ISSUE AT COMPONENT SUPPLIER."

INDUCTION / FUEL INJECTION CLEANING EQUIPMENT OR MATERIALS. THIS INCLUDES, BUT IS NOT LIMITED TO, ""VACU-FLUSH"" TYPE EQUIPMENT. CAUSE: THE USE OF NON-APPROVED EQUIPMENT CAN CAUSE THE ENGINES TO HYDRO-LOCK, OR CAUSE OTHER ENGINE DAMAGE, AND SOMETIMES THE ONLY POSSIBLE REPAIR IS TO REPLACE THE ENGINE."

THE START/ STOP IGNITION BUTTON IS PRESSED OR MAY RISE AND FALL IMMEDIATELY, PARTICULARLY WHERE AMBIENT TEMPERATURES ARE LESS THAN 4 DEGREES C. CAUSE: THE MOTOR WITHIN THE TRANSMISSION SELECTOR ASSEMBLY MAY BE AT THE LOWER END OF THE SPECIFICATION PREVENTING IT FROM RISING WITHIN THE REQUIRED TIME SPAN."

HIGHER TIME IN SERVICE VEHICLES, WHERE INSUFFICIENT PERFORMANCE OF THE AIR CONDITIONING COMPRESSOR HAS BEEN FOUND TO BE THE ROOT CAUSE OF THE ISSUE. COMPRESSOR PART NO. LR010723 & LR013934"

CAUSE: JLR ENGINEERING HAVE FOUND DURING THEIR INVESTIGATIONS THAT THE INSTRUMENT PANEL UPPER SECTION SPEAKER APERTURE BOLT MAY HAVE A RELAXED TORQUE (SEE TOPIX WORKSHOP MANUAL SECTION 76.46.04 FIG. E12471)"

CAUSE: THE TIMING CHAIN WAS NOT AT THE CORRECT TENSION. THIS WAS CAUSED BY THE FULL REPAIR PROCEDURE IN TSB LTB00474 NOT BEING FOLLOWED - A COMPLETE SET OF TIMING CHAIN TENSIONERS AND BLADES WERE NOT FITTED."

THICKNESS VARIATION (DTV) LEVELS ARE OUT OF SPECIFICATION CAUSING REPEATED PUSH BACKS ON THE BRAKE PISTONS/CALLIPERS."

OF TIME OR A LOW COOLANT LEVEL MESSAGE IS DISPLAYED IN THE MESSAGE CENTER. UPON INSPECTION, A LEAK MAY BE FOUND TO BE FROM THE FRONT OF THE ENGINE-DRIVEN COOLANT PUMP, TOGETHER WITH EXCESSIVE WEAR OF THE COOLANT PUMP BEARING."

ISSUE: OIL LEAK FROM TRANSFER CASE OUTPUT FLANGE CAUSE: THE CAUSE IS UNDER INVESTIGATION"

2F, P2405-00, P2406-00, P240A-00, P240B-00, P240C- 00, P2450-00 OR P2451-00 CAUSE: IF NO FAULT IS FOUND ON THE VEHICLE HAVING FOLLOWED THE LATEST DIAGNOSTIC GUIDANCE IN TOPIX, THE CAUSE MAY BE AN INTERNAL DMTL PUMP FAILURE."

ROVER / RANGE ROVER VEHICLES IN WARRANTY. CAUSE: UNKNOWN ENGINEERING INVESTIGATION ON-GOING."

ISSUE: LAND ROVER ARE CURRENTLY EVALUATING REPORTS WHERE DIAGNOSIS HAS LED TO A CONCERN WITH THE AIR SUSPENSION VALVE BLOCK ON DISCOVERY 4/ RANGE ROVER SPORT 10MY ONWARDS. CAUSE: CURRENTLY UNDER INVESTIGATION."

START THE ENGINE USING THE STOP/START BUTTON. WHEN THIS OCCURS, THE SMART KEY NOT FOUND MESSAGE IS NOT DISPLAYED AND THE ENGINE WILL NOT START WITH THE REMOTE KEY FOB IN THE FAILSAFE STARTING POSITION. CAUSE: THIS MAY BE CAUSED BY COMPONENT TOLERANCES WITHIN THE CENTRAL JUNCTION BOX (CJB) PREVENTING CORRECT FUNCTIONALITY DURING ENGINE START ATTEMPTS."

CAUSE: INCORRECT DIAGNOSIS ACTIONS: CONSIDER THE FOLLOWING IN THE FIRST INSTANCE WHEN INVESTIGATING WINDOW REGULATOR CONCERNS AND ITS OPERATION PRIOR TO REPLACING THE REGULATOR OR MOTOR: CUSTOMER MAY REPORT ONE OF THE FOLLOWING ISSUES:- A. WINDOW INOPERATIVE I.E. WILL NOT GO UP/DOWN, GOES UP/DOWN IN STAGES OR WILL NOT OPERATE AT ALL. B. WINDOW BOUNCE BACK OR NOT FULLY CLOSING. C. RATTLE OR NOISE DURING WINDOW OPERATION."

DIAGNOSIS MAY DETERMINE THAT THERE MAY BE SIGNS OF VISIBLE HEAT DAMAGE TO EITHER THE HEATED FRONT WINDSHIELD FUSES, HEATED FRONT WINDSHIELD RELAY, OR THE EJB / UNDERHOOD FUSE BOX. CAUSE: AT AMBIENT TEMPERATURES APPROXIMATELY BELOW 38F/4C, THE HEATED FRONT WINDSHIELD AND HEATED REAR WINDOW WILL TURN ON AUTOMATICALLY. THIS MEANS THE HEATED FRONT WINDSHIELD AND HEATED REAR WINDOW MAY BE ON FOR LONGER PERIODS OF TIME WITHOUT THE DRIVER KNOWING. THE EXTENDED OPERATION CAN RESULT IN OVERHEATING OF THE FUSES WITHIN THE ENGINE JUNCTION BOX (EJB) / UNDERHOOD FUSE BOX."

HIGHER TIME IN SERVICE VEHICLES, WHERE INSUFFICIENT PERFORMANCE OF THE AIR CONDITIONING COMPRESSOR HAS BEEN FOUND TO BE THE ROOT CAUSE OF THE ISSUE. COMPRESSOR PART NO. LR010723 & LR013934 ACTION: THE COMPRESSOR SUPPLIER IN CONJUNCTION WITH LAND ROVER ENGINEERING HAVE MADE IMPROVEMENTS TO THE COMPRESSORS TO IMPROVE THEIR SERVICE LIFE AND RELIABILITY, AND TWO IMPROVED COMPRESSORS HAVE BEEN SUPPLIED TO PARTS OPERATIONS LR010723 SUPERSEDES TO LR056364 LR013934 SUPERSEDES TO LR056365 PLEASE ENSURE THAT THE LATER PART NUMBER IS FITTED TO ANY VEHICLE THAT IS SUFFERING FROM LACK OF COMPRESSOR PERFORMANCE."

CAUSE: LAND ROVER ENGINEERING HAVE RECENTLY VISITED DEALERSHIPS WHERE A REQUEST HAS BEEN MADE TO REPLACE THE STEERING GEAR FOR AN OIL LEAK IN THE AREA OF THE PINION HOUSING, CASTING, YOKE PLUG OR THE GAITER ADJACENT TO THE PINION HOUSING. FOLLOWING INVESTIGATION THE SOURCE OF THE LEAK PATH WAS IDENTIFIED AS BEING FROM THE SUPPLY AND RETURN HOSE O-RING SEALS. SEE ATTACHED DOCUMENT FOR EXAMPLES."

THE ENGINE MALFUNCTION INDICATOR LAMP (MIL) MAY ALSO BE ILLUMINATED WITH MISFIRE DIAGNOSTIC TROUBLE CODES (DTC) P0301 THROUGH P0308 AND P0316, DEPENDING ON THE AFFECTED CYLINDER(S), STORED IN THE ENGINE CONTROL MODULE (ECM). CAUSE: THIS MAY BE CAUSED BY POOR FUEL QUALITY OR FUEL CONTAMINATION, LEADING TO CLOGGED FUEL INJECTORS AND RESTRICTING THE FUEL INJECTOR FLOW RATE."

CUSTOMER EXPERIENCES THE ENGINE OVERHEATING. CAUSE: THE REFILL PROCEDURE HAS NOT BEEN COMPLETED CORRECTLY, RESULTING IN INSUFFICIENT COOLANT IN THE ENGINE."

CAUSE: WHEN CHARGING A BATTERY (BOTH PRIMARY AND SECONDARY) WITH A BMS (BATTERY MONITORING SYSTEM) FITTED, THE EARTH FROM THE CHARGER MUST BE CONNECTED TO A SUITABLE CHASSIS OR ENGINE EARTH (CHECK TOPIX FOR APPROPRIATE LOCATION). THIS ALLOWS THE BMS TO SEE THE CURRENT GOING INTO THE BATTERY. HOWEVER WHEN USING A DIAGNOSTIC CHARGER FROM MIDTRONICS SUCH AS GR1, GRX GR8(110 VOLTS)THIS CONNECTION PROCESS CAN CAUSE AN INCORRECT BATTERY ANALYSIS DUE TO THE EXTRA RESISTANCE IN THE WIRING WHEN CONNECTED TO A CHASSIS OR ENGINE EARTH."

CAUSE: LAND ROVER ENGINEERING HAVE RECENTLY VISITED DEALERSHIPS WHERE A REQUEST HAS BEEN MADE TO REPLACE THE STEERING GEAR FOR AN OIL LEAK IN THE AREA OF THE PINION HOUSING, CASTING, YOKE PLUG OR THE GAITER ADJACENT TO THE PINION HOUSING. FOLLOWING INVESTIGATION THE SOURCE OF THE LEAK PATH WAS IDENTIFIED AS BEING FROM THE SUPPLY AND RETURN HOSE O-RING SEALS."

THIS MAYBE ACCOMPANIED WITH THE COOLANT GAUGE READING HIGH AND/OR THE CHARGE WARNING INDICATOR ILLUMINATED. INVESTIGATION FINDS A CONCERN WITH THE PRIMARY IDLER PULLEY ASSEMBLY WHICH IN SOME CASES CAN LEAD TO DAMAGE OF THE PRIMARY DRIVE BELT. THE PRIMARY BELT DRIVES THE COOLANT PUMP AND GENERATOR HENCE THE POTENTIAL FOR THE COOLANT GAUGE TO READ HIGH AND/OR THE CHARGE WARNING INDICATOR ILLUMINATING IF THE BELT IS DAMAGED AND NOT FUNCTIONING CORRECTLY. THIS CONCERNS AFFECTS LTIS (LOW TIME IN SERVICE) VEHICLES WITH THE 3.0 AJ126 AND 5.0 AJ133 GASOLINE ENGINES FITTED.

CAUSED BY TIMING CHAIN LEVER BEING WORNED AND REDUCING TENSION. MODEL 2010-2012 LR4, RANGE ROVER SPORT, RANGE ROVER. *PE

*LJ

GAITER ADJACENT TO PINION HOUSING, AND STEERING GEAR NEEDS REPLACING. MODEL RANGE ROVER SPORT, LR3, LR4. NO MODEL YEARS. *PE

*PE

OCCURS ON SOME 2010 LR4, RANGE ROVER, AND RANGE ROVER SPORT MODELS. *RM

AMBER OR RED SUSPENSION SYSTEM WARNING INDICATOR MAY ILLUMINATE AND SUSPENSION SYSTEM INACTIVE MAY DISPLAY IN THE MESSAGE CENTER OR THERE MAY BE A NOTICEABLE DEGRADATION OF SUSPENSION SYSTEM PERFORMANCE. *PE

AS A NATURAL PRODUCT AND THE CONDITIONS IT MAY CAUSE."

CAUSE: THIS MAY BE CAUSED BY THE MOLDING'S RETAINING CLIPS LOSING TENSION."

CAUSE: THIS MAY BE CAUSED BY THE MOLDING'S RETAINING CLIPS LOSING TENSION."

REAR* COOLER BOX ARE NOT OPERATING CAUSE CUSTOMER PERCEPTION"

CAUSE: DAMAGE/MARKING CAUSED BY OBJECT IMPACT AGAINST THE LENS. STAINING/DISCOLORATION CONTAMINATION CAUSED BY USING ANY TYPE OF CLEANING PRODUCT ON LENS."

USING THE IPOD/IPHONE USB CABLE ONLY, THE PLAYBACK SOUND MAY BE DISTORTED OR JUMPS/SKIPS. CAUSE: UNKNOWN, CURRENTLY UNDER INVESTIGATION."

CAUSE: THIS MAY BE CAUSED BY THE MOLDING'S RETAINING CLIPS LOSING TENSION."

ON CERTAIN MODEL VEHICLES MAY HAVE A CONCERN WITH QUALITY OF THE PROJECTION WELDING OF THE DRIVESHAFT CENTER BEARING MOUNT BRACKET. THE BRACKET MAY NOT IN ALL CASES HAVE BEEN ADEQUATELY WELDED. *PE

START UNAVAILABLE.

INFORMATION: THE AIR SUSPENSION RIDE LEVEL MODULE (RLM) AND ACTIVE DYNAMICS SUSPENSION MODULE B (SUMB) ECU'S INCLUDE ROBUST CHECKS OF THE HEIGHT SENSORS DURING VEHICLE USAGE. IF THERE IS A FAULT WITH THE HEIGHT SENSOR WIRING HARNESS, CONNECTOR, OR THE HEIGHT SENSOR COMPONENT ITSELF THEN THE SYSTEM ECU WILL STORE A HEIGHT SENSOR RELATED DTC."

INSTRUMENT CLUSTER FOR <1 SECOND (WHEN NO SERVICE IS REQUIRED). NO CUSTOMER SYMPTOMS UNTIL A SERVICE RESET HAS BEEN PERFORMED. WHEN AN ACTUAL SERVICE IS REQUIRED THE MESSAGE WILL APPEAR FOR 4 SECONDS AS DESIGN INTENT. CAUSE: DISTANCE TO NEXT SERVICE INITIALISATION VALUE MANAGEMENT BETWEEN ECM AND INSTRUMENT CLUSTER (FIRST 900MS)."

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE(TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE."

UPON DIAGNOSIS, THE TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES (DTC) B1D64-87 AND/OR B1D65-87 STORED IN THE HEADLAMP LEVELING CONTROL MODULE. CAUSE: THIS MAY BE CAUSED BY A SOFTWARE ERROR WITHIN THE HEADLAMP LEVELING CONTROL MODULE."

IF BLOCKAGE OCCURS WHILE ACC IS BEING USED, DRIVER INTERVENE AND/OR ""RADAR SENSOR BLOCKED"" MESSAGE WILL APPEAR ON THE CLUSTER AND DTC C1A67-97 SET. BLOCKAGE CAN ALSO OCCUR WHEN ACC IS NOT BEING USED. CAUSE: ""RADAR SENSOR BLOCKED"" INDICATES THAT THE ADAPTIVE SPEED CONTROL SYSTEM'S VISIBILITY HAS BEEN REDUCED DUE TO AN OBSTRUCTION. ACC CONTINUALLY SCANS FOR OBJECTS AHEAD AND, IF IT SEES NO OBJECTS I.E. VEHICLES, ROAD SIGNS, LAMP POSTS, GUARD RAILS ETC., IT WILL INDICATE A BLOCKAGE EVEN IF THE ACC IS NOT USED. THE C1A67-97 DTC FLAGS A RADAR BLOCKAGE SITUATION AND NOT A SYSTEM FAULT."

IF THE NAV BUTTON IS PRESSED A 2-5 SECOND PERIOD OF AM/ FM RADIO CAN BE HEARD AND THEN RETURNS BACK TO NO AUDIO. ISSUE WILL ONLY SELF-RECOVER AFTER AN IGNITION CYCLE. CAUSE: CURRENTLY UNDER ANALYSIS."

CAUSE: THIS MAY BE CAUSED BY A HD RADIO TUNER MODULE SOFTWARE ISSUE."

CAMERA), THE CAMERA IMAGE MAY BE LOST AND A BLUE SCREEN IS DISPLAYED. CAUSE: THIS MAY BE CAUSED BY SIGNAL LOSS FROM POOR CONNECTIONS, HARNESS ROUTING AND EXCESSIVE BENDING, THE HARNESS BEING TIGHTLY CLAMPED, AND DAMAGE TO THE INSULATION."

CAUSE: POOR CONNECTION AT THE CAMERA MODULE."

IF A BCM HAS BEEN DETERMINED TO REQUIRE REPLACEMENT FOLLOWING DIAGNOSIS, PLEASE CARRY OUT THE STEPS LISTED IN THE ACTION BELOW. CAUSE: CURRENTLY UNDER ANALYSIS."

23% WERE FOUND TO HAVE NO DEFECTS. CAUSE: ONE POSSIBLE REASON FOR THIS IS THAT ALL HO2S SENSORS ARE REPLACED WHEN ONLY ONE IS UNSERVICEABLE"

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE (TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE"

CAUSE: THESE ISSUES MAY BE CAUSED BY FRETTING CORROSION ACROSS THE FUEL SENDER HARNESS PINS INSIDE THE FUEL TANK."

OFF OF POWER TO THE HEADLAMPS, INSTRUMENT CLUSTER, AND TOUCH SCREEN ALL AT THE SAME TIME ACCOMPANIED BY A ""CLICKING"" NOISE SPECIFICALLY FROM THE INTERIOR FUSE BOX LOCATION BY THE GLOVE BOX. ALL SYSTEMS OPERATE NORMALLY THEREAFTER WITHOUT ANY OTHER CUSTOMER SYMPTOMS OR FAULT CODES."

CAUSE: THIS MAY BE CAUSED BY A CORRODED WIRING HARNESS AT THE FRONT AND/OR REAR BUMPER HARNESSES."

CAUSE ALTERNATORS ARE BEING DAMAGED DUE TO CROSS POLARITY WHEN THE VEHICLE IS JUMP STARTED."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD"

THIS CAN RESULT IN SDD REPORTING THAT THE RFA IS OFF BUS BY DISPLAYING A RED CROSS IN THE NETWORKS INTEGRITY SCREEN AND SDD NOT BEING ABLE TO RECOVER THE MODULE. CAUSE THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD OR A CORRUPTED SOFTWARE DOWNLOAD FILE."

PDIS AND THEN RETURNING THE VEHICLE TO A STORAGE COMPOUND WITHOUT REFITTING THE TRANSIT RELAY OR RETURNING THE VEHICLE TO TRANSIT MODE. TRANSIT MODE / TRANSIT RELAY ARE DESIGNED TO PROTECT THE CUSTOMERS BATTERY UP TO THE POINT OF DELIVERY. ALL VEHICLES IN STORAGE MUST HAVE THE TRANSIT RELAY IN PLACE OR BE IN TRANSIT MODE."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD."

CAUSE: THIS MAY BE CAUSED BY A CORRODED WIRING HARNESS AT THE FRONT AND/OR REAR BUMPER HARNESSES."

CAUSE: THIS MAY BE CAUSED BY CORRODED CHASSIS WIRING HARNESS AT THE REAR LEFT-SIDE CHASSIS-TO-BODY CONNECTOR.

CAUSE: AT AMBIENT TEMPERATURES APPROXIMATELY BELOW 38F/4C, THE HEATED WINDSHIELD AND HEATED REAR WINDOW WILL TURN ON AUTOMATICALLY. WHEN BOTH THEN AUTOMATICALLY TURN OFF, A LARGE LOAD CHANGE TO THE ELECTRICAL POWER SUPPLY SYSTEM MAY OCCUR. THIS LOAD CHANGE MAY LEAD THE CENTRAL JUNCTION BOX (CJB) TO ENTER A LOAD PROTECTION COUNTERMEASURE."

CAUSE: THESE ISSUES MAY BE CAUSED BY FRETTING CORROSION ACROSS THE FUEL SENDER HARNESS PINS INSIDE THE FUEL TANK."

IS LOCATED IN THE CENTER CONSOLE CUPHOLDER. CAUSE: THIS MAY BE CAUSED BY LOW SMART KEY HANDSET BATTERY VOLTAGE OR WHERE A MOBILE PHONE, LAPTOP, OR OTHER RELATED ELECTRONIC DEVICE IS PLACED IN CLOSE PROXIMITY TO THE SMART KEY HANDSET. IT IS IMPORTANT TO ESTABLISH IF ANY OF THESE ARE THE CASE BEFORE CONTINUING WITH EITHER SERVICE INSTRUCTION. IF NONE OF THESE ARE EVIDENT, IT MAY BE CAUSED BY NON-LINEARITY OF THE HANDSET LF AMPLIFIER."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD."

(DTC) B11DB-87 STORED IN THE BODY CONTROL MODULE (BCM). CAUSE: THIS MAY BE CAUSED BY A BLOWN BATTERY MONITORING SYSTEM (BMS) FUSED HARNESS."

AVAILABLE, IS NOT SHOWING AS PAIRED BUT IS AVAILABLE, IS DIFFICULT TO PAIR, AUDIO FRAGMENTS WHEN STREAMING MUSIC AND/OR OTHER UNEXPECTED BEHAVIOR. CAUSE: THIS CAN BE A RESULT OF REDUCED PHONE POWER DUE TO THE FOLLOWING:- BATTERY LIFE SOFTWARE UPDATE ON THE CUSTOMERS DEVICE, OTHER APPLICATIONS RUNNING IN THE BACKGROUND ON THE CUSTOMERS DEVICE (SUCH AS GAMES, SOCIAL MEDIA APPS, SEARCHING FOR NUMEROUS PAIRED DEVICES). A BREAK IN THE LINE OF SIGHT FROM THE IAM TO THE CUSTOMER DEVICE (E.G. DEVICE IN POCKET CAUSING ATTENUATION BY THE HUMAN BODY). ANOMALIES INTRODUCED WITH SOFTWARE UPDATES OF DEVICE THAT MAY REDUCE THE EFFECTIVENESS OF AUTHENTICATION BETWEEN THE CUSTOMER DEVICE AND THE VEHICLE. NOTE: THESE ISSUES ARE WELL DOCUMENTED ON OFFICIAL PHONE MANUFACTURERS SUPPORT WEB SITES."

NO LEARNING, FAILURE OF WHEEL SENSOR TEST, REACT AS IF THEY ARE STUCK IN SHIPPING MODE. REGARDLESS OF ANY DRIVING CYCLE THE PARTS WILL NEVER GO INTO THE CORRECT WORKING MODE. CAUSE: SERVICE PARTS HAVE BEEN DELIVERED IN THE ""WRONG MODE""."

THE AUDIO/VIDEO BUTTON ON TOUCH-SCREEN HOME PAGE MAY ALSO BE GREYED OUT. CAUSE: ONE OF THE MODULES SITUATED ON THE MOST BUS, SUCH AS AUDIO AMPLIFIER MODULE OR AUDIO CONTROL MODULE, HAVE A SOFTWARE CONFLICT."

TROUBLE CODE (DTC) U0128-00 STORED IN THE INSTRUMENT CLUSTER (IC); FUEL GAUGE INOPERATIVE; FUEL GAUGE NOT SHOWING MORE THAN HALF FULL; FUEL GAUGE FLUCTUATES; AND/OR FUEL GAUGE SWITCHES ON/OFF INTERMITTENTLY. CAUSE: THESE ISSUES MAY BE CAUSED BY: LR4, RANGE ROVER SPORT ONLY: SOFTWARE ISSUE WITHIN THE INSTRUMENT CLUSTER (IC). BACKED-OUT PINS IN ANY OF THE FOLLOWING AREAS: INTERNAL TO THE FUEL TANK (SENDER WIRING), FUEL PUMP MODULE, AND/OR FUEL TANK FLANGE ASSEMBLY. FRETTING CORROSION ACROSS THE FUEL SENDER HARNESS PINS INSIDE THE FUEL TANK (BLACK CONNECTORS)."

HOWEVER YOU SHOULD ALWAYS REFER TO THE DIAGNOSTIC SECTION FOR EACH SYSTEM IN THE WORKSHOP MANUAL BEFORE REPLACING ANY MODULES. ISSUE A LARGE NUMBER OF NAVIGATION MODULES ARE BEING REPLACED AND WHEN TEST BY THE SUPPLIER ARE ""NO FAULT FOUND""."

THE VEHICLE SEAT MEMORY MODULE LOGS U1A4C 00, BUILD END OF LINE MODE ACTIVE CAUSE THE SEAT MODULE HAS BEEN INCORRECTLY CONFIGURED TO THE VEHICLE."

FAULT CODES STARTING WITH C1A ESPECIALLY C1A36-01 LOGGED. POSSIBILITY THAT ADDITIONAL WARNING LIGHTS MAY BE DISPLAYED AND ADDITIONAL FAULT CODES STORED. CAUSE THE HARNESS HAS BEEN INCORRECTLY ROUTED AND IS PRESSING AGAINST THE WASHER FILLER TUBE CAUSING INSULATION DAMAGE AND A SHORT CIRCUIT/OPEN CIRCUIT"

MODEL VEHICLES AFFECTED; LR4 2010-2013, LR2, RANGE ROVER SPORT 2010-2013, RANGE ROVER 2010-2012. *LJ

LIGHTS ARE DISPLAYED IN THE INSTRUMENT CLUSTER. MODEL 2005-2009 LR3 (LA), 2006-2013 RANGE ROVER SPORT (LS), 2010-2013 LR4 (LA). *PE

MODEL 2010-2013 LR4. *PE

*LJ

*PE

*PE

*RM

OWNER'S EXPERIENCE, AFFECTED VEHICLES MAY REQUIRE A NUMBER OF MODULE SOFTWARE UPDATES AND THE VEHICLE BATTERY CONDITION TESTED AND, IF NECESSARY, REPLACED. *PE

AMBER OR RED SUSPENSION WARNING INDICATOR MAY ILLUMINATE WITH SUSPENSIONS SYSTEM INACTIVE DISPLAYED IN MESSAGE CENTER OR MAY BE A NOTICEABLE DEGRADATION IN SUSPENSION SYSTEM PERFORMANCE. SUSPENSION SYSTEM CONTROL MODULE SOFTWARE UPDATE MAY ONLY BE PERFORMED AFTER A SUSPENSION SYSTEM COMPRESSOR REPLACEMENT. *PE

IN CERTAIN MODEL VEHICLES A POTENTIAL CONCERN RELATES TO THE FRONT DOOR HARNESS NOT BEING RETAINED DUE TO INCORRECTLY MANUFACTURED EDGE CLIPS. AS A CONSEQUENCE, THE HARNESS HAS THE POTENTIAL TO CHAFE ON THE INNER DOOR PANEL. *PE UPDATED 04/20/11 *PE

SOME VEHICLES ARE FITTED WITH THE VERY LATEST SOFTWARE AND PARTS TO FURTHER ENHANCE THE CUSTOMER'S EXPERIENCE OF THESE MODELS, AFFECTED VEHICLES WILL REQUIRE A NUMBER OF MODULE SOFTWARE UPDATES AND THE VEHICLE BATTERY CONDITION TESTED AND, IF NECESSARY, REPLACED. CSC LETTER WAS REC'D. *PE

stations drop in and out on a regular basis.

IN ADDITION THE CURRENT VEHICLE LOCATION INDICATOR WILL NOT LOCK ONTO THE CORRECT LOCATION ON THE MAP. CAUSE: SOFTWARE ERROR."

CAUSE: THIS MAY BE CAUSED BY AN INSTRUMENT CLUSTER SOFTWARE ERROR."

CAUSE THERE IS A POTENTIAL THAT THE TOP WINDSCREEN SEAL HAS BECOME DISLODGED OVER TIME CAUSING A WINDNOISE"

DIAGNOSTIC TROUBLE CODES (DTC) ARE STORED. CAUSE: THIS MAY BE CAUSED BY VARIOUS ISSUES."

WHICH IS NOT COMPATIBLE WITH LAND ROVER INFOTAINMENT SYSTEMS. CAUSE THIS IS TO MAKE YOU AWARE OF THE TYPES OF MEDIA THAT MAY CAUSE THE UNIT TO FAIL WITH THE CUSTOMER."

ONLY), THE CAMERA IMAGE MAY BE LOST AND A BLUE SCREEN IS DISPLAYED CAUSE: THIS MAY BE CAUSED BY SIGNAL LOSS THROUGH THE COAX."

'HOOD OPEN' MESSAGE IS DISPLAYED ON THE INSTRUMENT CLUSTER; AND/OR A MISLOCK SOUND IS EMITTED WHEN LOCKING THE VEHICLE. CAUSE: THESE ISSUES MAY BE CAUSED BY A FAULTY HOOD OPEN SWITCH."

WHICH IS NOT COMPATIBLE WITH LAND ROVER INFOTAINMENT SYSTEMS. CAUSE THIS IS TO MAKE YOU AWARE OF THE TYPES OF MEDIA THAT MAY CAUSE THE UNIT TO FAIL WITH THE CUSTOMER. THEY ARE COPY CONTROL COMPACT DISCS (CCCD) RECORDABLE COMPACT DISCS (CD-R) REWRITABLE COMPACT DISCS (CD-RW) ECO DISCS, WHICH ARE VERY THIN, ONLY 0.6MM. PLEASE REFER TO ATTACHMENT FOR EXAMPLES OF DISCS THAT ARE KNOWN TO HAVE CAUSED DAMAGE."

CAUSE: SOFTWARE COMPATIBILITY ISSUES"

MANUFACTURED AWAY FROM PROCESS AND, IN SOME CASES, A BLUE SCREEN IS DISPLAYED WHEN CAMERA MODE IS SELECTED AND THE CAMERA SYSTEM IS UNABLE TO BE USED."

CAUSE: SOFTWARE COMPATIBILITY ISSUES"

'HOOD OPEN' MESSAGE IS DISPLAYED ON THE INSTRUMENT CLUSTER; AND/OR A MISLOCK SOUND IS EMITTED WHEN LOCKING THE VEHICLE. CAUSE: THESE ISSUES MAY BE CAUSED BY A FAULTY HOOD OPEN SWITCH."

ONLY), THE CAMERA IMAGE MAY BE LOST AND A BLUE SCREEN IS DISPLAYED CAUSE: THIS MAY BE CAUSED BY SIGNAL LOSS THROUGH THE COAX."

CAUSE: INCORRECT DIAGNOSIS."

VARIOUS CONDITIONS THAT CONTRIBUTE TO THE OPERATION OF THE WINDOW REGULATOR NOT OPERATING"

CAUSE: THIS MAY BE CAUSED BY A TOLERANCE STACK-UP BETWEEN THE DOOR MIRROR AND THE DOOR AND/OR THE RETAINING SCREWS MAY BE LOOSE/UNDER TORQUED."

WHICH DEMONSTRATES THE ISSUE.

CAUSE: THIS MAY BE CAUSED BY A TOLERANCE STACK-UP BETWEEN THE DOOR MIRROR AND THE DOOR AND/OR THE RETAINING SCREWS MAY BE LOOSE/UNDER TORQUED."

CAUSE: THIS MAY BE CAUSED BY A BUILD-UP OF DIRT AND GREASE ON THE SURFACE OF THE WINDSHIELD GLASS."

CAUSE. THE WIRES TO THE SWITCH HAVE CORRODED AND ARE POSSIBLY BROKEN."

CAUSE. THE WIRES TO THE SWITCH HAVE CORRODED AND ARE POSSIBLY BROKEN."

CAUSE. THE WIRES TO THE SWITCH HAVE CORRODED AND ARE POSSIBLY BROKEN."

CLADDING IS COMING ADRIFT/LOOSE OR A GAP IS EVIDENT.THE ATTACHED FILE SHOWS EXAMPLES. CAUSE UNDER INVESTIGATION"

CAUSE: THIS MAY BE CAUSED BY A TOLERANCE STACK-UP BETWEEN THE DOOR MIRROR AND THE DOOR."

CAUSE THE ROOT CAUSE WAS FOUND TO BE THAT ANTI RUST OIL RESIDUE REMAINS ON THE SUPPLIER'S TOOLING AT THE START OF A PRODUCTION RUN."

THE DOORS MAY NOT OPEN FROM EITHER SIDE OR MAY NOT LOCK. *RM

IT IS POSSIBLE THAT THERE IS INADEQUATE SEALANT AT THE LEFT HAND (LH) AND RIGHT HAND (RH) A POST COWL AREA, WHICH COULD RESULT IN WATER INGRESS INTO THE FOOTWELL. *PE

*PE

UPON INSPECTION, LOW PRESSURE IS RECORDED ON THE HIGH PRESSURE SYSTEM, HIGH PRESSURE IS RECORDED ON THE LOW PRESSURE SYSTEM, AND THE COMPRESSOR CLUTCH (WHERE APPLICABLE) IS WORKING PROPERLY.

INSTRUMENT PACK WITH ASSOCIATED DTC'S FOR BRAKE LIGHT SWITCH (P0504-27, P0504-62, C1A96-64) OR BRAKES SHOWING SIGNS OF DRAG AND BINDING. CAUSE: INCORRECT BRAKE LIGHT SWITCH SETTING. NOTE: ANALYSIS OF RETURNED BRAKE SWITCHES HAVE SHOWN NO ISSUES WITH THE BRAKE SWITCH ITSELF. DO NOT REPLACE THE SWITCH BEFORE ADJUSTMENT IS CARRIED OUT."

CAUSE: THIS MAY BE CAUSED BY A CRACKED TRANSMISSION HEAT SHIELD MOUNTING BRACKET."

DTC P1707-72 IS FOUND TO BE STORED IN THE TCM (TRANSMISSION CONTROL MODULE). CAUSE: EPRL (EMERGENCY PARK RELEASE LEVER) NOT LOCKED DOWN FROM PDI."

CAUSE: THIS MAY BE CAUSED BY POOR BRACKET PAINT FINISH AND / OR LOW TORQUE ON THE SADDLE CLAMP NUT, ALLOWING THE PIPED TO RUB THROUGH THE PAINT."

CAUSE: OIL OR GREASE LEAK PAST INPUT SHAFT SEAL THROUGH NORMAL USE OR SEAL FAILURE."

TO RISE OR INITIALLY RISES BEFORE LOWERING ITSELF BACK TO ITS DEFAULT POSITION FOR AN IGNITION OFF STATE, WHICH IS CONFIRMED BY DTC P176B - 71 (TRANSMISSION RANGE SELECTOR UP AND DOWN POSITION CONTROL ERROR) CAUSE: POTENTIAL OF A MIXED STOCK CONDITION"

*RM UPDATED 5/17/11. *PE

AND MATERIALS ACROSS THE VEHICLE INTERIOR THAT HAVE MADE CONTACT WITH THE ICP AND OR ROTARY DIALS."

*LJ

GAUGE AND SWITCHES ON/OFF INTERMITTENTLY, WHICH IS CAUSED BY AN ISSUE WITHIN INSTRUMENT CLUSTER (IC) SOFTWARE. MODEL 2008-2012 LR2, 2010-2013 LR4, 2010-2013 RANGE ROVER SPORT, 2010-2012 RANGE ROVER. *PE UPDATED 11/25/14. *PE

*PE UPDATED 08/28/2012 *JS UPDATED 3/8/13. *PE UPDATED 8/16/13. *PE

*RM UPDATED 5/17/11. *PE

WITH A WHEEL SPEED SENSOR ONLY.

CAUSE BRAKE LIGHT SWITCH / BRAKE PEDAL SHIM INTERACTION. NOTE: NOT ALL VEHICLES WILL BE FITTED WITH BRAKE PEDAL SHIM."

CAUSE: DAMAGE TO THE CALIPER FINISH WHILE CLEANING THE VEHICLE AND, OR THE ROAD WHEELS"

THIS WILL OCCUR WITHOUT THE BRAKE PEDAL BEING PRESSED AND SETTING OFF FROM STATIONARY / DRIVING AT LOW SPEEDS. CAUSE: THE ACTION OF THE BIAS SPRING WITHIN THE REAR BRAKE SHOE MECHANISM WHEN COMBINED WITH INCORRECT ADJUSTMENT OR WEAR OF THE SYSTEM."

VEHICLES WITH STANDARD BRAKES ONLY. CAUSE: BRAKE COMPRESSIBILITY OF THE PAD, WHILST WITHIN SPECIFICATION, MAY BE SLIGHTLY INCOMPATIBLE WITH THE DRIVING STYLE AND VEHICLE USAGE PATTERNS OF A SMALL NUMBER OF CUSTOMERS. WHILTST THERE IS NO IMPACT ON THE EFFICIENCY OF THE BRAKING SYSTEM, IN SOME CIRCUMSTANCES THIS MAY LEAD TO NOISE BECOMING APPARENT."

CAUSE: ASSEMBLY GREASE/FLUID IS PRESENT FROM THE MANUFACTURING PROCESS AND GIVES A SIMILAR APPEARANCE TO A BRAKE FLUID LEAK."

CAUSE: ASSEMBLY GREASE/ FLUID IS PRESENT FROM THE MANUFACTURING PROCESS AND GIVES A SIMILAR APPEARANCE TO A BRAKE FLUID LEAK."

CAUSE: THIS MAY BE CAUSED BY THE CONTACTS IN THE HORN PAD."

*RM

VEHICLES MAY EXHIBIT ONE OR MORE OF THE FOLLOWING: A RUBBING/SQUEAK NOISE FROM THE REAR/PARKING BRAKE WHEN THE VEHICLE IS MOVING; EVIDENCE OF PARKING BRAKE SHOE DRAG (HEAT BUILD UP/EXCESSIVE PARKING BRAKE SHOE LINING WEAR; AND A SCREECH NOISE WHEN APPLYING OR RELEASING THE ELECTRIC PARKING BRAKE (EPB) WHILE THE VEHICLE IS STATIONARY.) *PE

CAUSE: THIS IS EITHER CAUSED BY THE SHIPPING PROCESS AND SHOULD BE CLAIMED THROUGH TRANSPORT / DISTRIBUTION OR IT IS CAUSED DURING JLR MANUFACTURING PROCESSES AND SHOULD BE CLAIMED AS PER WARRANTY POLICY."

DIFFICULT TO OPERATE (DOES NOT FOLD OR 'STICKS' WHEN OPERATING). CAUSE: THIS MAY BE CAUSED BY THE SEAT OPERATING LEVER BEING OUT OF ALIGNMENT."

THIS CAN CAUSE THE ALARM TO TRIGGER OR THE VEHICLE TO NOT LOCK.

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES"

CAUSE: DAMAGE/MARKING CAUSED BY OBJECT IMPACT AGAINST THE LENS. STAINING/DISCOLORATION CONTAMINATION CAUSED BY USING ANY TYPE OF CLEANING PRODUCT ON LENS. IMPORTANT: OWNERS HANDBOOK SPECIFIES TO CLEAN WITH A LIGHTLY MOISTENED CLOTH AND DO NOT USE CHEMICAL AGENTS OR DOMESTIC CLEANERS ACTION WHERE A CUSTOMER CONCERN IS REPORTED, PLEASE ORDER THE LENS KIT FOR THE RELEVANT MODEL"

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OUTSIDE OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE PERFORMANCE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES."

CAUSE: THIS MAY BE CAUSED BY THE DESIGN OF THE TAIL LAMP ASSEMBLY ALLOWING MOISTURE TO SETTLE ON THE INSIDE OF THE LAMP LENS."

CAUSE: UNDER INVESTIGATION"

ACTION: WHEN DIAGNOSING CUSTOMER CONCERNS RELATING TO THE HYDRAULIC POWER STEERING SYSTEM, REFER TO THE SERVICE INFORMATION BELOW."

THE ISSUE IS COMMON ACROSS ALL MANUFACTURERS SYMPTOMS WHEN THE APPLE DEVICE IS CONNECTED TO THE CAR SYSTEM AND A CALL IS RECEIVED THERE IS NO OPTION TO ANSWER OR REJECT THE INCOMING CALL ON THE SYSTEM. THE STEERING WHEEL CONTROLS ALSO HAVE NO EFFECT. THE TOUCH SCREEN CONTINUES TO DISPLAY THE PHONE SCREEN. THE POP-UP SCREEN TO ANSWER OR REJECT THE CALL IS NOT SHOWN."

CAUSE: THIS MAY BE CAUSED BY A ROAD WHEEL/TIRE ASSEMBLY IMBALANCE AND/OR TEMPORARY TIRE FLAT-SPOTTING.

When the returned components are tested they are found to have no faults.

INSTRUMENT PACK EVEN THOUGH THE HOOD / BONNET IS CLOSED CAUSE: THERE IS A POTENTIAL THAT AN INTERNAL SPRING COULD BECOME DISLODGED"

DIAGNOSTIC TROUBLE CODE (DTC) C1A20-64 MAY BE STORED. VEHICLES WITHIN THE ABOVE VIN RANGES HAVE BEEN FITTED WITH EITHER A HITACHI OR AN OLD-DESIGN AMK SUSPENSION COMPRESSOR."

CAUSE: REAR WHEEL BEARING NOISY OR DIFFICULT TO TURN."

(SEE FIG.1) ACTION: REPLACE BY PRESSING ON NEW BUTTON CAP PART NO: LR045801 (SEE FIG.2)"

*RM

BECOME ILLUMINATED ON THE INSTRUMENT PACK OF THEIR VEHICLE. *JS

*PE

(blowing warm and then cold); ? Windshield, rear window, and/or door windows mist up in cool (15C or lower) ambient temperatures; ? Poor cooling performance of the Air Conditioning (A/C) system; and/or ? Warm, damp or musty smells coming from the vents.