2014 Land Rover LR2 TSBs

area while driving.

Up on customer complaint of a a noisy power steering pump or heavy steering, should a dealer intend to change a powerr steering pump to resolve this, please address the questions below on a EPQR so that JLR may review and potentially request the part back for further engineering investigation. Pre 13MY only, vehicles fitted with SI6 Petrol Engines only.

driving or starting engine.

exhibits poor starting; and/or ? Engine MIL (Malfunction Indicator Lamp) illuminated with DTC (Diagnostic Trouble Code) P0300, P0301, P0302, P0303, P0304, and/or P1315 stored in the Powertrain Control Module (PCM).

poor starting; and/or ? Engine MIL (Malfunction Indicator Lamp) illuminated with DTC (Diagnostic Trouble Code) P0300, P0301, P0302, P0303, P0304, and/or P1315 stored in the Powertrain Control Module (PCM).

poor starting; and/or ? Engine MIL (Malfunction Indicator Lamp) illuminated with DTC (Diagnostic Trouble Code) P0300, P0301, P0302, P0303, P0304, and/or P1315 stored in the Powertrain Control Module (PCM).

Diagnostic Trouble Code (DTC) P0016, P0017, P0026, or P0341 may be stored in the Powertrain Control Module (PCM).

poor starting; and/or ? Engine Malfunction Indicator Lamp (MIL) illuminated with Diagnostic Trouble Codes (DTC) P0300, P0301, P0302, P0303, P0304, and/or P1315 stored in the Powertrain Control Module (PCM).

The Diagnostic Trouble Code (DTC) that may be logged include P0016, P0017, P0026, or P0341.

Pack) for low coolant level and coolant visible on the ground at the front area of the engine bay. On inspection, the coolant leak is from the radiator.

visible on the ground at the front area of the engine bay.

CAUSE ALTERNATOR REGULATOR FAULTY IN ALTERNATOR PART NUMBER LR028121."

DISPLAYED IN THE INSTRUMENT CLUSTER; ENGINE FAILS TO CRANK; VEHICLE MAY NOT UNLOCK / LOCK WHEN USING PASSIVE ENTRY OR WHEN PRESSING A SMART KEY BUTTON.

(DTC) STORED IN THE POWERTRAIN CONTROL MODULE (PCM) AND NO HARDWARE FAULT: P011621: ENGINE COOLANT TEMPERATURE SENSOR 1 CIRCUIT RANGE/PERFORMANCE (FAULT ON START UP AFTER USING BLOCK HEATER) P011B22: ENGINE COOLANT TEMPERATURE / INTAKE AIR TEMPERATURE CORRELATION (FAULT ON START UP AFTER USING BLOCK HEATER) P013A00: O2 SENSOR SLOW RESPONSE RICH TO LEAN (BANK 1 AND SENSOR 2) P131500: PERSISTENT MISFIRE P030000: RANDOM MISFIRE DETECTED P030100: CYLINDER 1 MISFIRE DETECTED P030200: CYLINDER 2 MISFIRE DETECTED P030300: CYLINDER 3 MISFIRE DETECTED P030400: CYLINDER 4 MISFIRE DETECTED"

CAUSE: INVESTIGATIONS SHOW THE BOLTS THAT CONNECT THE TURBOCHARGER TO THE DOWNPIPE (2.0L GTDI GASOLINE ENGINES) OR TURBOCHARGER TO MANIFOLD (2.2L DIESEL ENGINES) ARE INSECURE OR MISSING."

ROUGH IDLE, HESITATION AND/OR LOSS OF POWER. ONE OR MORE OF THE FOLLOWING DTCS MAY BE SET IN THE PCM: P008A, P008B, P2542. CAUSE: SUB-OPTIMAL PCM SOFTWARE CALIBRATION"

EVOQUE (L538) VEHICLES WHICH MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE."

(L538) VEHICLES WHICH MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

UPON FURTHER INVESTIGATION, A TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE (DTC) P0961-62 STORED IN THE FAULT MEMORY. CAUSE: THIS MAY BE CAUSED BY INSUFFICIENT SPRING LOAD FOR MOTOR BRUSHES IN THE ACTIVE ON-DEMAND COUPLING OIL PUMP."

EVOQUE (L538) VEHICLES WHICH MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE"

INSTRUMENT CLUSTER: FAULTY GENERATOR FAULTY BATTERY MONITORING SYSTEM (BMS) THE CHARGE WARNING INDICATOR IS ILLUMINATED WHEN THE ENGINE IS RUNNING. CAUSE: THE POWER SUPPLY IS A FULLY INTEGRATED SYSTEM THAT REQUIRES SDD TO DIAGNOSE OVERALL FUNCTIONALITY ROBUSTLY TO MAKE SURE CUSTOMER SATISFACTION IS MET VIA RIGHT FIRST TIME DIAGNOSIS."

THE DIAGNOSTIC TROUBLE CODE (DTC) THAT MAY BE LOGGED INCLUDE P0016, P0017, P0026, OR P0341.

EVOQUE (L538) VEHICLES WHICH MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE."

(L538) VEHICLES WHICH MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE. ACTION: RETAILERS ARE REQUIRED TO HOLD ONLY AFFECTED NEW VEHICLES THAT ARE WITHIN YOUR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW VEHICLE SALE PENDING COMPLETION OF THE SERVICE INSTRUCTION DETAILED IN THIS TECHNICAL BULLETIN."

MALFUNCTION INDICATOR LAMP (MIL) MAY BE ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTC) P0116-21, P011B-22, P2183-00, OR P2183-22 STORED IN THE ENGINE CONTROL MODULE (ECM) AND NO HARDWARE FAULT. CAUSE: THIS MAY BE CAUSED BY AN ON-BOARD DIAGNOSTICS (OBD) CALIBRATION ERROR."

DIAGNOSTIC TROUBLE CODE (DTC) P1315 MAY BE STORED. CAUSE: THIS MAY BE CAUSED BY INCONSISTENCIES IN THE VEHICLE CALIBRATION COMBINED WITH MOISTURE ENTERING THE ENGINE THROUGH THE AIR INTAKE SYSTEM."

STORED IN THE ENGINE CONTROL MODULE (ECM). CAUSE: THIS MAY BE CAUSED BY AN INTERNAL FAULT WITH THE LOW PRESSURE FUEL SENSOR."

P228D-00 OR P228C-77 STORED IN THE ENGINE CONTROL MODULE (ECM). ADDITIONALLY, THE ENGINE MAY EXPERIENCE ROUGH RUNNING, HARD STARTING, A ROUGH IDLE, OR MISFIRES AND ONE OR MORE MISFIRE DTCS (P0300, P0301, P0302, P0303, P0304, AND P1315) STORED IN THE ECM. CAUSE: THIS MAY BE CAUSED BY AN INTERNAL FAULT WITH THE METERING VALVE IN THE HIGH PRESSURE FUEL PUMP"

DISPLAYED IN THE INSTRUMENT CLUSTER; ENGINE FAILS TO CRANK; VEHICLE MAY NOT UNLOCK / LOCK WHEN USING PASSIVE ENTRY OR WHEN PRESSING A SMART KEY BUTTON. CAUSE: THIS MAY BE CAUSED BY A 'LOCK UP' OF THE KEYLESS VEHICLE MODULE (KVM)."

COOLANT PUMP LEAKS FROM WEEP CHAMBER. (SEE ATTACHED PICTURE)"

CAUSE: INTERNAL ISSUE WITHIN CLUTCH."

THEREFORE WOULD APPRECIATE MORE INFORMATION TO AID INVESTIGATIONS. KNOWN ISSUES HAVE BEEN RESOLVED AND ASSURED VINS FOR EFFECTED MODELS ARE: EVOQUE: H021033(15MY), H920134 (PUNE) DISCOVERY 4 A756425 FREELANDER2: H432120, H911856 (PUNE)"

THE DTC THAT MAY BE LOGGED INCLUDE P0016-76, P0341-00, P000A-00, OR P0026-00. THERE HAVE ALSO BEEN SOME REPORTS OF MISFIRE CODES BEING STORED (P03XX). CAUSE: THE PIN ON THE CAMSHAFT SPROCKET HAS BROKEN. SEE ATTACHED FILE FOR AN EXAMPLE."

INDUCTION / FUEL INJECTION CLEANING EQUIPMENT OR MATERIALS. THIS INCLUDES, BUT IS NOT LIMITED TO, ""VACU-FLUSH"" TYPE EQUIPMENT. CAUSE: THE USE OF NON-APPROVED EQUIPMENT CAN CAUSE THE ENGINES TO HYDRO-LOCK, OR CAUSE OTHER ENGINE DAMAGE, AND SOMETIMES THE ONLY POSSIBLE REPAIR IS TO REPLACE THE ENGINE."

WARRANTY DATA INDICATES A VOLUME OF FUEL INJECTORS BEING REPLACED IN RELATION TO THE SYMPTOM OUTLINED BELOW: VEHICLES SUFFERING FROM A MISFIRE AT COLD START AND ON SOME OCCASIONS INTERMITTENT ROUGH RUNNING AT NORMAL OPERATING TEMPERATURE, WITH VARIOUS DTC'S STORED SUCH AS P0300-00 P0301-00 P0302-00 P0304-00 P1315-00 P0316-00 CAUSE: ENGINEERING WOULD LIKE TO GAIN FURTHER UNDERSTANDING INTO THE CAUSE OF THESE FUEL INJECTOR FAILURES."

CAUSE: INVESTIGATIONS SHOW THE BOLTS THAT CONNECT THE TURBOCHARGER TO THE DOWNPIPE (2.0L GTDI GASOLINE ENGINES) OR TURBOCHARGER TO MANIFOLD (2.2L DIESEL ENGINES) ARE INSECURE OR MISSING."

ROVER EVOQUE (L538) VEHICLES WITHIN THE LISTED VIN RANGES WHERE DIAGNOSTIC TROUBLE CODE (DTC) P0089-29, FUEL PRESSURE REGULATOR PERFORMANCE - SIGNAL INVALID, IS STORED IN THE ENGINE CONTROL MODULE (ECM) AND THE ENGINE MALFUNCTION INDICATOR LAMP (MIL) IS ILLUMINATED IN THE INSTRUMENT CLUSTER MESSAGE CENTER."

ROVER EVOQUE (L538) VEHICLES WITHIN THE LISTED VIN RANGES WHERE DIAGNOSTIC TROUBLE CODE (DTC) P0089-29, FUEL PRESSURE REGULATOR PERFORMANCE - SIGNAL INVALID, IS STORED IN THE ENGINE CONTROL MODULE (ECM) AND THE ENGINE MALFUNCTION INDICATOR LAMP (MIL) IS ILLUMINATED IN THE INSTRUMENT CLUSTER MESSAGE CENTER. ACTION: RETAILERS ARE REQUIRED TO HOLD ALL AFFECTED VEHICLES WITHIN THE LISTED VIN RANGE THAT ARE IN THEIR CONTROL AND REFRAIN FROM RELEASING THE VEHICLES FOR NEW OR USED VEHICLE SALE PENDING COMPLETION OF THE REWORK ACTION DETAILED IN THIS TECHNICAL BULLETIN"

ROVER / RANGE ROVER VEHICLES IN WARRANTY. CAUSE: UNKNOWN ENGINEERING INVESTIGATION ON-GOING."

WITH RELATED DTCS C2007-11 OR C2008-11. CAUSE: JLR ENGINEERING ARE CONTINUING TO INVESTIGATE ROOT CAUSE OF THE ISSUE."

ISSUES WITH RELATED DTCS C2007-11 OR C2008-11. CAUSE: JLR ENGINEERING ARE CONTINUING TO INVESTIGATE ROOT CAUSE OF THE ISSUE."

CAUSE: WHEN CHARGING A BATTERY (BOTH PRIMARY AND SECONDARY) WITH A BMS (BATTERY MONITORING SYSTEM) FITTED, THE EARTH FROM THE CHARGER MUST BE CONNECTED TO A SUITABLE CHASSIS OR ENGINE EARTH (CHECK TOPIX FOR APPROPRIATE LOCATION). THIS ALLOWS THE BMS TO SEE THE CURRENT GOING INTO THE BATTERY. HOWEVER WHEN USING A DIAGNOSTIC CHARGER FROM MIDTRONICS SUCH AS GR1, GRX GR8(110 VOLTS)THIS CONNECTION PROCESS CAN CAUSE AN INCORRECT BATTERY ANALYSIS DUE TO THE EXTRA RESISTANCE IN THE WIRING WHEN CONNECTED TO A CHASSIS OR ENGINE EARTH."

CAUSE: LAND ROVER ENGINEERING HAVE RECENTLY VISITED DEALERSHIPS WHERE A REQUEST HAS BEEN MADE TO REPLACE THE STEERING GEAR FOR AN OIL LEAK IN THE AREA OF THE PINION HOUSING, CASTING, YOKE PLUG OR THE GAITER ADJACENT TO THE PINION HOUSING. FOLLOWING INVESTIGATION THE SOURCE OF THE LEAK PATH WAS IDENTIFIED AS BEING FROM THE SUPPLY AND RETURN HOSE O-RING SEALS."

MAY EXPERIENCE REDUCED POWER OR PERCEPTION OF A MISFIRE AND DIFFICULTY RESTARTING THE ENGINE.

PERFORMANCE, AND MALFUNCTION INDICATOR LAMP (MIL) IS ILLUMINATED IN INSTRUMENT CLUSTER (IP) MESSAGE CENTER. MODEL 2013-2014 LR2, 2012-2014 EVOQUE. *PE

TROUBLE CODE (DTC) P0089-29, CAUSING ENGINE MALFUNCTION INDICATOR LAMP (MIL) TO ILLUMINATE IN MESSAGE CENTER OF INSTRUMENT CLUSTER. MODEL 2013-2014 LR2, 2012-2014 RANGE ROVER EVOQUE. *PE

Reports of key case bulging

AS A NATURAL PRODUCT AND THE CONDITIONS IT MAY CAUSE."

ATTACHMENT ""IMG_2720"")."

CAUSE: ROOT CAUSE, PINION TAIL BEARING SPALLING CAUSED BY SUBSURFACE MATERIAL DEFORMATION. CAUSE OF SUBSURFACE DEFORMATION IS STATIC OVERLOAD."

REPAIR PROCEDURE."

CAUSE POOR RETENTION OF THE RETAINING CLIPS THAT ATTACH THE LEVER TO THE VENT."

REAR OF THE VEHICLE, DEALER DIAGNOSIS IDENTIFIES THE NOISE IS COMING FROM THE REAR DIFFERENTIAL ASSEMBLY. CAUSE: THE PINION TAIL BEARING IS WORN DUE TO STATIC OVER LOADING."

USING THE IPOD / IPHONE USB CABLE ONLY, THE PLAYBACK SOUND MAY BE DISTORTED OR JUMPS/SKIPS. CAUSE: UNKNOWN, CURRENTLY UNDER INVESTIGATION."

USING THE IPOD/IPHONE USB CABLE ONLY, THE PLAYBACK SOUND MAY BE DISTORTED OR JUMPS/SKIPS. CAUSE: UNKNOWN, CURRENTLY UNDER INVESTIGATION."

TECHNICIAN'S MAY IDENTIFY A 'BLACK SLUDGE' TYPE SUBSTANCE IN THE OIL,FILTER,HALDEX PUMP AS SHOWN IN THE PICTURE ATTACHED. CAUSE: THE 'BLACK SLUDGE' IS FROM THE ADDITIVES IN THE OIL SOLIDIFYING OUT IN THE COLD OIL."

CUSTOMER REPORTS SMART KEY NOT FOUND.

(HLDF) on occasions may fail to download software correctly resulting in no communications with the module and blank screen.

Retailers are testing the primary battery using the Midtronics EXP-1080 tester which is reporting the battery is serviceable. The vehicle then returns with the same Customer concern of ECO Stop/Start inoperative. If a Midtronics GRX-3080 is used, the primary battery fails the test. Replacement of the primary battery resolves the concern.

RETURNED TO THE SUPPLIER (DENSO) TO INVESTIGATE FOR POSSIBLE DEFECTS."

NOT APPLICABLE TO VEHICLES FITTED WITH ACTIVE DRIVELINE. LOSS OF ALL WHEEL DRIVE FUNCTIONALITY CAUSING THE VEHICLE TO OPERATE IN 2 WHEEL DRIVE ONLY.CAUSE: DURING REPLACEMENT AND CONFIGURATION OF A NEW RDCM, DAMAGE MAY BE CAUSED TO THE PRINTED CIRCUIT BOARD (PCB) WITHIN THE RDCM DUE TO THE CONNECTION OF THE BATTERY EARTH CABLE."

INTERMITTENT: - THE CURRENT VEHICLE POSITION DISPLAYED IS 'WASHINGTON D.C.' AND NOT THE ACTUAL CURRENT POSITION. ONCE A GPS SIGNAL IS ACQUIRED, THE CURRENT VEHICLE POSITION WILL THEN BE CORRECTLY DISPLAYED. - ROUTE GUIDANCE IS NOT AFFECTED DURING THIS INTERMITTENT FAULT MODE; IF THE ISSUE OCCURRED DURING ROUTE GUIDANCE, THE CURRENT ROUTE WILL CONTINUE TO BE DISPLAYED. B. PERMANENT: - THE CURRENT VEHICLE POSITION DISPLAYED IS 'WASHINGTON D.C.' AND NOT THE ACTUAL CURRENT POSITION. THE CURRENT VEHICLE POSITION WILL CONTINUE TO BE INCORRECTLY DISPLAYED AS 'WASHINGTON D.C.' FOLLOWING AN IGNITION CYCLE ('OFF' / 'ON'). - ROUTE GUIDANCE IS AFFECTED DURING THIS PERMANENT FAULT MODE; IF THE ISSUE OCCURRED DURING ROUTE GUIDANCE, THE CURRENT ROUTE WILL NOT RESUME AND THE DESTINATION WILL BE CANCELLED. - ALL PREVIOUS DESTINATIONS WILL BE DELETED (BUTTON 'GRAYED OUT'). CAUSE: THESE MAY BE CAUSED BY A SOFTWARE ISSUE OR HARD FAULT WITH THE INTEGRATED AUDIO MODULE (IAM). ACTION: SHOULD A CUSTOMER EXPRESS THIS CONCERN, FOLLOW APPROPRIATE SERVICE INSTRUCTION [A OR B] OUTLINED BELOW. A. INTERMITTENT: UPDATE THE INTEGRATED AUDIO MODULE (IAM) SOFTWARE. B. PERMANENT: REPLACE THE INTEGRATED AUDIO MODULE (IAM)."

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE(TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE."

ASSOCIATED COMPONENTS REPLACED FOR A NON-START CONDITION. FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORISED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

CAUSE: DURING REPLACEMENT AND CONFIGURATION OF A NEW RDCM, DAMAGE MAY BE CAUSED TO THE PRINTED CIRCUIT BOARD (PCB) WITHIN THE RDCM DUE TO THE CONNECTION OF THE BATTERY EARTH CABLE."

FOR FAULT CODES LOGGED IN THE KVM (KEYLESS VEHICLE MODULE) ALSO KNOWN AS THE RFA (REMOTE FUNCTION ACTUATOR) F000-63/U3000-63, CONTROL MODULE - CIRCUIT/ COMPONENT PROTECTION TIME-OUT IS LOGGED. CAUSE THIS DTC IS SET WHEN THE KVM HAS GONE THROUGH A SELF RESET"

ASSOCIATED COMPONENTS REPLACED FOR A NON-START CONDITION. FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORISED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

IF A BCM HAS BEEN DETERMINED TO REQUIRE REPLACEMENT FOLLOWING DIAGNOSIS, PLEASE CARRY OUT THE STEPS LISTED IN THE ACTION BELOW. CAUSE: CURRENTLY UNDER ANALYSIS."

LINE DISPLAY FRONT (HLDF), MAY BE WRONGLY REPLACED WHEN TROUBLESHOOTING IF ISSUES ARE INCORRECTLY ATTRIBUTED TO IT. CAUSE: THE TS MAY BE INCORRECTLY DIAGNOSED AS THE SOURCE OF THE FAULT AND REPLACED IN ERROR."

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE (TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE"

ACTION WHEN YOU SWITCH ON THE IGNITION AND HEADLAMPS IF THE BALLAST MODULE HAS FAILED YOU CAN CLEARLY HERE A TICKING AS THE BALLAST MODULE IS TRYING TO STRIKE. THESE TICKS ARE RAPID (SOUND LIKE A BIRD CHEEPING) AND SOUND 10 TIMES BEFORE SWITCHING OFF. TO CONFIRM THE BALLAST MODULE IS AT FAULT REPEAT THE PROCEDURE, THE LAMPS AND THE BALLAST MODULE WILL RETRY AND AGAIN PRODUCE THE TICKING SOUND IF THE BALLAST MODULE IS AT FAULT"

CAUSE: THIS MAY BE CAUSED BY A CORRODED WIRING HARNESS AT THE FRONT AND/OR REAR BUMPER HARNESSES."

FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORISED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

CAUSE ALTERNATORS ARE BEING DAMAGED DUE TO CROSS POLARITY WHEN THE VEHICLE IS JUMP STARTED."

FOLLOWING SUPPLIER ANALYSIS THE MODULES HAVE BEEN CATEGORIZED AS ""NO FAULT FOUND"". CAUSE CURRENTLY UNDER ANALYSIS."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD"

THIS CAN RESULT IN SDD REPORTING THAT THE RFA IS OFF BUS BY DISPLAYING A RED CROSS IN THE NETWORKS INTEGRITY SCREEN AND SDD NOT BEING ABLE TO RECOVER THE MODULE. CAUSE THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD OR A CORRUPTED SOFTWARE DOWNLOAD FILE."

PDIS AND THEN RETURNING THE VEHICLE TO A STORAGE COMPOUND WITHOUT REFITTING THE TRANSIT RELAY OR RETURNING THE VEHICLE TO TRANSIT MODE. TRANSIT MODE / TRANSIT RELAY ARE DESIGNED TO PROTECT THE CUSTOMERS BATTERY UP TO THE POINT OF DELIVERY. ALL VEHICLES IN STORAGE MUST HAVE THE TRANSIT RELAY IN PLACE OR BE IN TRANSIT MODE."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD."

CAUSE: THESE ISSUES MAY BE CAUSED BY FRETTING CORROSION ACROSS THE FUEL SENDER HARNESS PINS INSIDE THE FUEL TANK."

ISSUE: A CUSTOMER MAY REPORT A CONCERN THAT WHEN TRYING TO ACCESS THE PREFERENCES ON THE TOUCH SCREEN DISPLAY THEY ENCOUNTER ERRORS OR GREYED OUT BUTTONS. CAUSE: AUDIO CONTROL MODULE SOFTWARE ISSUES."

A. INTERMITTENT: - THE CURRENT VEHICLE POSITION DISPLAYED IS 'WASHINGTON D.C.' AND NOT THE ACTUAL CURRENT POSITION. ONCE A GPS SIGNAL IS ACQUIRED, THE CURRENT VEHICLE POSITION WILL THEN BE CORRECTLY DISPLAYED. - ROUTE GUIDANCE IS NOT AFFECTED DURING THIS INTERMITTENT FAULT MODE; IF THE ISSUE OCCURRED DURING ROUTE GUIDANCE, THE CURRENT ROUTE WILL CONTINUE TO BE DISPLAYED. B. PERMANENT: - THE CURRENT VEHICLE POSITION DISPLAYED IS 'WASHINGTON D.C.' AND NOT THE ACTUAL CURRENT POSITION. THE CURRENT VEHICLE POSITION WILL CONTINUE TO BE INCORRECTLY DISPLAYED AS 'WASHINGTON D.C.' FOLLOWING AN IGNITION CYCLE ('OFF' / 'ON'). - ROUTE GUIDANCE IS AFFECTED DURING THIS PERMANENT FAULT MODE; IF THE ISSUE OCCURRED DURING ROUTE GUIDANCE, THE CURRENT ROUTE WILL NOT RESUME AND THE DESTINATION WILL BE CANCELLED. - ALL PREVIOUS DESTINATIONS WILL BE DELETED (BUTTON 'GRAYED OUT')."

THE VEHICLE SEAT MEMORY MODULE LOGS U1A4C 00, BUILD END OF LINE MODE ACTIVE CAUSE THE SEAT MODULE HAS BEEN INCORRECTLY CONFIGURED TO THE VEHICLE."

WHEN THE KEY HANDSET REMOTE IS OPERATED. CAUSE: CURRENTLY UNDER ANALYSIS."

the Instrument Pack even though the Hood/Bonnet is closed.

bulging.

CAUSE: PART SUPPLY CONSTRAINTS."

CAUSE: THIS MAY BE CAUSED BY A TOLERANCE STACK-UP BETWEEN THE DOOR MIRROR AND THE DOOR AND/OR THE RETAINING SCREWS MAY BE LOOSE/UNDER TORQUED."

CAUSE: OIL FILTER LR001247 SUPERSEEDS TO LR030778 WHICH IS SUPPLIED WITH A NEW SEAL. THIS SEAL IS SLIGHTLY LARGER IN DIAMETER THAN THE ONE SUPPLIED WITH LR001247"

CAUSE: A NEW PART AND PART NUMBER ARE AVAILABLE."

CAUSE: THIS MAY BE CAUSED BY A TOLERANCE STACK-UP BETWEEN THE DOOR MIRROR AND THE DOOR AND/OR THE RETAINING SCREWS MAY BE LOOSE/UNDER TORQUED."

CAUSE: THIS MAY BE CAUSED BY A BUILD-UP OF DIRT AND GREASE ON THE SURFACE OF THE WINDSHIELD GLASS."

CAUSE: THIS MAY BE CAUSED BY THE HANDSET MANUFACTURING PROCESS."

CAUSE: THIS MAY BE CAUSED BY WATER PASSING THROUGH THE HIGH-MOUNTED STOP LAMP SEAL."

ISSUE: THE PRIMARY DOOR SEALS COME ADRIFT FROM THE BODY AT THE BOTTOM OF THE DOOR APERTURE. CAUSE: THE CAUSE IS BEING INVESTIGATED AND INFORMATION IS REQUIRED TO HELP ESTABLISH ROOT CAUSE."

CAUSE: THIS MAY BE CAUSED BY THE HANDSET MANUFACTURING PROCESS."

CAUSE: THE CAUSE IS BEING INVESTIGATED AND INFORMATIONIS REQUIRED TO HELP ESTABLISH ROOT CAUSE."

CAUSE: THIS MAY BE CAUSED BY THE HANDSET MANUFACTURING PROCESS."

THE VEHICLE CAUSE: THE CAUSE OF THE PARTS COMING ADRIFT IS UNDER INVESTIGATION BUT AS THE PARTS ARE A ONE TIME FIT ITEM REFITTING THEM USING ADHESIVE OR DOUBLE SIDED TAPE WILL NOT WORK"

BULGING.

*PE

exhibit intermittent operation, causing one or more of the following issues: ? Audio volume does not adjust (up and/or down)? Radio 'seek' buttons do not operate ? Volume control buttons cause the radio station to change ? InControl system slow to operate (blank screen followed by the 'Land Rover' logo) ? Transmission paddle shifters do not operate ? Diagnostic Trouble Codes (DTC) U2013-02 and/or B1D21-13 stored

EXAMPLES ARE: A ROUGH GEAR CHANGE OR 'JERK' FROM STATIONARY WHEN SELECTING DRIVE(D) FROM NEUTRAL(N). A ROUGH GEAR CHANGE OR 'JERK' WHEN RELEASING THE FOOT BRAKE FROM A STATIONARY POSITION WHILE THE VEHICLE IS IN DRIVE(D) (HANDBRAKE NOT APPLIED). FOR EXAMPLE, IN A TRAFFIC JAM OR PULLING AWAY FROM TRAFFIC LIGHTS. A ROUGH GEAR CHANGE OR 'JERK' WHILE DRIVING VEHICLE ON COASTDOWN FROM SIXTH GEAR (OFF ACCELERATOR) BUT ONLY WHEN DOWNSHIFTING FROM FIFTH TO FOURTH GEAR. CAUSE: THIS MAY BE CAUSED BY TRANSMISSION CONTROL MODULE (TCM) SOFTWARE PROGRAMMING."

CRUISE CONTROL) AND TRANSMISSION PADDLE SWITCHES MAY EXHIBIT INTERMITTENT OPERATION, CAUSING ONE OR MORE (LIST NOT EXHAUSTIVE) OF THE FOLLOWING ISSUES: AUDIO VOLUME WILL NOT ADJUST (UP AND/OR DOWN) RADIO SEEK BUTTONS WILL NOT OPERATE VOLUME CONTROL BUTTONS CAUSE THE RADIO STATION TO CHANGE THE INFOTAINMENT SYSTEM IS SLOW TO OPERATE (BLANK SCREEN FOLLOWED BY THE 'LAND ROVER' LOGO) DIAGNOSTIC TROUBLE CODE (DTC) U2013-02 'SWITCH PACK, GENERAL SIGNAL FAILURE' IS STORED IN THE INSTRUMENT CLUSTER MEMORY DTC B1D21-13 'REMOTE CONTROL SWITCH CIRCUIT OPEN' IS STORED IN THE TOUCH SCREEN MEMORY TRANSMISSION PADDLE SWITCHES INOPERATIVE OR INTERMITTENT FUNCTIONALITY CRUISE CONTROL INOPERATIVE"

UPON DIAGNOSIS, DIAGNOSTIC TROUBLE CODE (DTC) P1889-14 IS FOUND TO BE STORED. CAUSE: THIS MAY BE CAUSED BY INSUFFICIENT SPRING LOAD FOR COMMUTATOR BAR BRUSHES IN THE ACTIVE ON-DEMAND COUPLING OIL PUMP."

BUTTON MECHANISM HAS BEEN MODIFIED TO PREVENT THIS ISSUE FROM VIN NO. H372254 UK BUILD L910950 PUNE BUILD"

ISSUE: A TECHNICIAN MAY FIND WHEN REPLACING THE M66 GEARBOX TURRET HOUSING FOR A GEAR CHANGE SELECTION OR STOP/START FAULT THAT AN INCORRECT TURRET MAY BE SUPPLIED. THIS AFFECTS: VEHICLES FITTED WITH M66 6 SPEED MANUAL TRANSMISSIONS FREELANDER 2/LR2 (LF) MODEL YEAR: 2013-2014 (VIN: DH321215-EH439912) RANGE ROVER EVOQUE (LV) MODEL YEAR: 2013 ONWARDS (VIN: DH85818 ONWARDS) CAUSE: IN MARCH 2013 A HALL EFFECT SENSOR TURRET WAS INTRODUCED, BUT WAS NOT GIVEN A SERVICE PART NUMBER. DEALERS ORDERING PART NO.LR022071 MAY HAVE EITHER THE AN INDUCTIVE OR HALL EFFECT TURRET SUPPLIED. THIS MAY BE INCORRECT FOR THE VEHICLE BEING REPAIRED."

BUTTON MECHANISM HAS BEEN MODIFIED TO PREVENT THIS ISSUE FROM VIN NO. H372254 UK BUILD L910950 PUNE BUILD ACTION: TO RESOLVE THIS ISSUE PLEASE REPLACE THE GEAR SELECTOR KNOB ONLY

CAUSE: OIL OR GREASE LEAK PAST INPUT SHAFT SEAL THROUGH NORMAL USE OR SEAL FAILURE."

BUTTON MECHANISM HAS BEEN MODIFIED TO PREVENT THIS ISSUE FROM VIN NO. H372254 UK BUILD L910950 PUNE BUILD"

2/LR2 PRODUCTS, DEALERS HAVE BEEN REPLACING COMPLETE STEERING GEAR ASSEMBLIES. CAUSE: PREVIOUSLY, THE INNER BALL JOINTS WERE NOT AVAILABLE AS SEPARATE LOWER LEVEL REPAIR ITEMS THROUGH MICROCAT."

AN ISSUE WITH STEERING OR STEERING GEARS. MODEL LR4 (L319), LR2 (L359), RANGE ROVER SPORT (L320). *PE

JOINT, AS A SEPARATE LEVEL REPAIR, WAS NOT AVAILABLE. MODEL FREELANDER 2, LR2. *PE

MECHANISM OF INTERLOCK BUTTON WILL BE MODIFIED. *PE

to respond or no functionality at all.

to respond or no functionality at all.

Range where the tailgate exterior release switch may display intermittent switching performance issues.

exterior release switch may display intermittent switching performance issues.

DIAGNOSTIC TROUBLE CODES (DTC) ARE STORED. CAUSE: THIS MAY BE CAUSED BY VARIOUS ISSUES."

WHICH IS NOT COMPATIBLE WITH LAND ROVER INFOTAINMENT SYSTEMS. CAUSE THIS IS TO MAKE YOU AWARE OF THE TYPES OF MEDIA THAT MAY CAUSE THE UNIT TO FAIL WITH THE CUSTOMER."

'HOOD OPEN' MESSAGE IS DISPLAYED ON THE INSTRUMENT CLUSTER; AND/OR A MISLOCK SOUND IS EMITTED WHEN LOCKING THE VEHICLE. CAUSE: THESE ISSUES MAY BE CAUSED BY A FAULTY HOOD OPEN SWITCH."

WHICH IS NOT COMPATIBLE WITH LAND ROVER INFOTAINMENT SYSTEMS. CAUSE THIS IS TO MAKE YOU AWARE OF THE TYPES OF MEDIA THAT MAY CAUSE THE UNIT TO FAIL WITH THE CUSTOMER. THEY ARE COPY CONTROL COMPACT DISCS (CCCD) RECORDABLE COMPACT DISCS (CD-R) REWRITABLE COMPACT DISCS (CD-RW) ECO DISCS, WHICH ARE VERY THIN, ONLY 0.6MM. PLEASE REFER TO ATTACHMENT FOR EXAMPLES OF DISCS THAT ARE KNOWN TO HAVE CAUSED DAMAGE."

CAUSE: SOFTWARE COMPATIBILITY ISSUES"

CAUSE: SOFTWARE COMPATIBILITY ISSUES ACTION: IF A CUSTOMER REPORTS THE CONCERN DETAILED ABOVE AN HLDF SOFTWARE UPDATE WILL BE REQUIRED USING SDD. TO COMPLETE THE UPDATE FOLLOW THE INSTRUCTIONS BELOW:-"

IT HAS BEEN SWITCHED OFF BY THE USER ACTION :- IF INVESTIGATING A CUSTOMER COMPLAINT OF NO GRIDLINES ON THE GRAPHICAL DISPLAY, THEN PLEASE FOLLOW THE INSTRUCTIONS DESCRIBED IN THE ATTACHMENT OR THE VEHICLE HANDBOOK."

CAUSE: SOFTWARE COMPATIBILITY ISSUES"

CAUSE: THIS MAY BE CAUSED BY RADIO INTERFERENCE."

CAUSE: INCORRECT DIAGNOSIS."

Dealer Data Update

Dealer Data Update

Dealer Data Update

Dealer Data Update

BE FOUND WITHIN THE POWER STEERING FLUID SYSTEM WHICH COULD LEAD TO SYSTEM CONTAMINATION AND A DETERIORATION IN SYSTEM PERFORMANCE. CAUSE: INTERNAL DEBRIS FROM A SUSPECTED COMPONENT MALFUNCTION MAY RESULT IN THE POWER STEERING FLUID BECOMING CONTAMINATED."

ACTION: WHEN DIAGNOSING CUSTOMER CONCERNS RELATING TO THE HYDRAULIC POWER STEERING SYSTEM, REFER TO THE SERVICE INFORMATION BELOW."

THE ISSUE IS COMMON ACROSS ALL MANUFACTURERS SYMPTOMS WHEN THE APPLE DEVICE IS CONNECTED TO THE CAR SYSTEM AND A CALL IS RECEIVED THERE IS NO OPTION TO ANSWER OR REJECT THE INCOMING CALL ON THE SYSTEM. THE STEERING WHEEL CONTROLS ALSO HAVE NO EFFECT. THE TOUCH SCREEN CONTINUES TO DISPLAY THE PHONE SCREEN. THE POP-UP SCREEN TO ANSWER OR REJECT THE CALL IS NOT SHOWN."

FLAT SPOTS ON THE ROLLING SURFACE OF THE TIRE. CAUSE: TEMPORARY FLAT SPOTS NATURALLY DEVELOP ON THE ROLLING SURFACE OF A TIRE WHEN THE WHEELS OF THE VEHICLE ARE STATIONARY OVER A PERIOD OF TIME."

CAUSE: THIS MAY BE CAUSED BY A ROAD WHEEL/TIRE ASSEMBLY IMBALANCE AND/OR TEMPORARY TIRE FLAT-SPOTTING.

HALOGEN BULB - LR044458. CAUSE: LTB00841 HAS BEEN TEMPORARILY REMOVED FROM TOPIX IN ORDER TO PROCURE SUFFICIENT PARTS FROM JLR SUPPLIERS - PARTS ARE DUE TO BE MADE AVAILABLE TO MARKETS IN WEEK 4 OF 2016, UPON WHICH, THE BULLETIN WILL BE RELEASED FOR PUBLICATION."

HALOGEN BULB - LR044458. CAUSE: LTB00841 HAS BEEN TEMPORARILY REMOVED FROM TOPIX IN ORDER TO PROCURE SUFFICIENT PARTS FROM JLR SUPPLIERS."

CAUSE: THIS MAY LEAD TO EARLIER THAN EXPECTED BULB REPLACEMENT."

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES"

CAUSE: DAMAGE/MARKING CAUSED BY OBJECT IMPACT AGAINST THE LENS. STAINING/DISCOLORATION CONTAMINATION CAUSED BY USING ANY TYPE OF CLEANING PRODUCT ON LENS. IMPORTANT: OWNERS HANDBOOK SPECIFIES TO CLEAN WITH A LIGHTLY MOISTENED CLOTH AND DO NOT USE CHEMICAL AGENTS OR DOMESTIC CLEANERS ACTION WHERE A CUSTOMER CONCERN IS REPORTED, PLEASE ORDER THE LENS KIT FOR THE RELEVANT MODEL"

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OUTSIDE OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE PERFORMANCE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES."

(SEE FIG.1) ACTION: REPLACE BY PRESSING ON NEW BUTTON CAP PART NO: LR045801 (SEE FIG.2)"

CAUSE: IF UPON INSPECTION THE COOLING SYSTEM DOES NOT SHOW EVIDENCE OF WHERE COOLANT MAY HAVE ESCAPED, IT IS POSSIBLE AIR WAS NOT FULLY PURGED FROM THE SYSTEM DURING THE FILL PROCESS AT THE FACTORY. OVER TIME THIS AIR WILL MOVE TO THE HEADER TANK CAUSING THE COOLANT LEVEL TO DROP."

OUTSIDE THE VIN RANGE IN THE BULLETIN. THERE IS ALSO EVIDENCE THAT THE BULLETIN HAS BEEN COMPLETED ON EVOQUE. SPECIAL SERVICE MESSAGES 46477, 54417 AND 55837 ALSO REFER TOLTB00342. ACTION: THE REPAIR OUTLINED IN LTB00342 (CURRENTLY AT VERSION 2) MUST ONLY BE COMPLETED ON FREELANDER 2 (LR2) WITHIN THE BULLETIN VIN RANGE 000212 TO 257090. AT VIN 257091 AN IMPROVED PINION BEARING DESIGN WAS INTRODUCED ALONG WITH A DESIGN CHANGE TO THE DIFFERENTIAL."

INSTRUMENT PACK EVEN THOUGH THE HOOD / BONNET IS CLOSED CAUSE: THERE IS A POTENTIAL THAT AN INTERNAL SPRING COULD BECOME DISLODGED"

THE ISSUE IS IDENTIFIED AS A CLICK NOISE FROM A FRONT DRIVE SHAFT (HALF SHAFT). CAUSE: SMALL AMOUNT OF MOVEMENT OF THE SPLINES OF THE SHAFT WITHIN THE HUB."

CAUSE: DAMAGE TO THE CALIPER FINISH WHILE CLEANING THE VEHICLE AND, OR THE ROAD WHEELS"

HALEWOOD BUILT VEHICLES ONLY - IDENTIFIED BY THE 11TH DIGIT OF THE VIN = 'H' FREELANDER 2 (L359) VEHICLES VIN: ALL EVOQUE (L538) VEHICLES UPTO VIN: H991051. PUNE BUILT VEHICLES ONLY - IDENTIFIED BY THE 11TH DIGIT OF THE VIN = 'L') FREELANDER (L359) VEHICLES VIN: ALL EVOQUE (L538) VEHICLES VIN: N/A (NOT AFFECTED)"