2010 Land Rover LR2 TSBs

AS A NATURAL PRODUCT AND THE CONDITIONS IT MAY CAUSE."

ATTACHMENT ""IMG_2720"")."

CAUSE: ROOT CAUSE, PINION TAIL BEARING SPALLING CAUSED BY SUBSURFACE MATERIAL DEFORMATION. CAUSE OF SUBSURFACE DEFORMATION IS STATIC OVERLOAD."

REPAIR PROCEDURE."

ISSUE REPORTS OF KEY CASE BULGING. SEE ATTACHED PHOTO. CAUSE KEYS WERE MANUFACTURED OVERSIZE."

REAR OF THE VEHICLE, DEALER DIAGNOSIS IDENTIFIES THE NOISE IS COMING FROM THE REAR DIFFERENTIAL ASSEMBLY. CAUSE: THE PINION TAIL BEARING IS WORN DUE TO STATIC OVER LOADING."

ISSUE REPORTS OF KEY CASE BULGING. SEE ATTACHED PHOTO."

CAUSE: THIS MAY BE CAUSED BY LOOSE HORN LINK LEAD CONNECTOR TERMINALS."

USING THE IPOD/IPHONE USB CABLE ONLY, THE PLAYBACK SOUND MAY BE DISTORTED OR JUMPS/SKIPS. CAUSE: UNKNOWN, CURRENTLY UNDER INVESTIGATION."

CAUSE: THIS MAY BE CAUSED BY LOOSE HORN LINK LEAD CONNECTOR TERMINALS."

TECHNICIAN'S MAY IDENTIFY A 'BLACK SLUDGE' TYPE SUBSTANCE IN THE OIL,FILTER,HALDEX PUMP AS SHOWN IN THE PICTURE ATTACHED. CAUSE: THE 'BLACK SLUDGE' IS FROM THE ADDITIVES IN THE OIL SOLIDIFYING OUT IN THE COLD OIL."

CUSTOMER REPORTS SMART KEY NOT FOUND.

(HLDF) on occasions may fail to download software correctly resulting in no communications with the module and blank screen.

Retailers are testing the primary battery using the Midtronics EXP-1080 tester which is reporting the battery is serviceable. The vehicle then returns with the same Customer concern of ECO Stop/Start inoperative. If a Midtronics GRX-3080 is used, the primary battery fails the test. Replacement of the primary battery resolves the concern.

RETURNED TO THE SUPPLIER (DENSO) TO INVESTIGATE FOR POSSIBLE DEFECTS."

NOT APPLICABLE TO VEHICLES FITTED WITH ACTIVE DRIVELINE. LOSS OF ALL WHEEL DRIVE FUNCTIONALITY CAUSING THE VEHICLE TO OPERATE IN 2 WHEEL DRIVE ONLY.CAUSE: DURING REPLACEMENT AND CONFIGURATION OF A NEW RDCM, DAMAGE MAY BE CAUSED TO THE PRINTED CIRCUIT BOARD (PCB) WITHIN THE RDCM DUE TO THE CONNECTION OF THE BATTERY EARTH CABLE."

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE(TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE."

CAUSE: DURING REPLACEMENT AND CONFIGURATION OF A NEW RDCM, DAMAGE MAY BE CAUSED TO THE PRINTED CIRCUIT BOARD (PCB) WITHIN THE RDCM DUE TO THE CONNECTION OF THE BATTERY EARTH CABLE."

FOR FAULT CODES LOGGED IN THE KVM (KEYLESS VEHICLE MODULE) ALSO KNOWN AS THE RFA (REMOTE FUNCTION ACTUATOR) F000-63/U3000-63, CONTROL MODULE - CIRCUIT/ COMPONENT PROTECTION TIME-OUT IS LOGGED. CAUSE THIS DTC IS SET WHEN THE KVM HAS GONE THROUGH A SELF RESET"

IF A BCM HAS BEEN DETERMINED TO REQUIRE REPLACEMENT FOLLOWING DIAGNOSIS, PLEASE CARRY OUT THE STEPS LISTED IN THE ACTION BELOW. CAUSE: CURRENTLY UNDER ANALYSIS."

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE (TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE"

CAUSE: THESE ISSUES MAY BE CAUSED BY FRETTING CORROSION ACROSS THE FUEL SENDER HARNESS PINS INSIDE THE FUEL TANK."

CAUSE: THIS MAY BE CAUSED BY A CORRODED WIRING HARNESS AT THE FRONT AND/OR REAR BUMPER HARNESSES."

CAUSE ALTERNATORS ARE BEING DAMAGED DUE TO CROSS POLARITY WHEN THE VEHICLE IS JUMP STARTED."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD"

PDIS AND THEN RETURNING THE VEHICLE TO A STORAGE COMPOUND WITHOUT REFITTING THE TRANSIT RELAY OR RETURNING THE VEHICLE TO TRANSIT MODE. TRANSIT MODE / TRANSIT RELAY ARE DESIGNED TO PROTECT THE CUSTOMERS BATTERY UP TO THE POINT OF DELIVERY. ALL VEHICLES IN STORAGE MUST HAVE THE TRANSIT RELAY IN PLACE OR BE IN TRANSIT MODE."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE: THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD."

CAUSE: THESE ISSUES MAY BE CAUSED BY FRETTING CORROSION ACROSS THE FUEL SENDER HARNESS PINS INSIDE THE FUEL TANK."

ISSUE: A CUSTOMER MAY REPORT A CONCERN THAT WHEN TRYING TO ACCESS THE PREFERENCES ON THE TOUCH SCREEN DISPLAY THEY ENCOUNTER ERRORS OR GREYED OUT BUTTONS. CAUSE: AUDIO CONTROL MODULE SOFTWARE ISSUES."

AVAILABLE, IS NOT SHOWING AS PAIRED BUT IS AVAILABLE, IS DIFFICULT TO PAIR, AUDIO FRAGMENTS WHEN STREAMING MUSIC AND/OR OTHER UNEXPECTED BEHAVIOR. CAUSE: THIS CAN BE A RESULT OF REDUCED PHONE POWER DUE TO THE FOLLOWING:- BATTERY LIFE SOFTWARE UPDATE ON THE CUSTOMERS DEVICE, OTHER APPLICATIONS RUNNING IN THE BACKGROUND ON THE CUSTOMERS DEVICE (SUCH AS GAMES, SOCIAL MEDIA APPS, SEARCHING FOR NUMEROUS PAIRED DEVICES). A BREAK IN THE LINE OF SIGHT FROM THE IAM TO THE CUSTOMER DEVICE (E.G. DEVICE IN POCKET CAUSING ATTENUATION BY THE HUMAN BODY). ANOMALIES INTRODUCED WITH SOFTWARE UPDATES OF DEVICE THAT MAY REDUCE THE EFFECTIVENESS OF AUTHENTICATION BETWEEN THE CUSTOMER DEVICE AND THE VEHICLE. NOTE: THESE ISSUES ARE WELL DOCUMENTED ON OFFICIAL PHONE MANUFACTURERS SUPPORT WEB SITES."

TROUBLE CODE (DTC) U0128-00 STORED IN THE INSTRUMENT CLUSTER (IC); FUEL GAUGE INOPERATIVE; FUEL GAUGE NOT SHOWING MORE THAN HALF FULL; FUEL GAUGE FLUCTUATES; AND/OR FUEL GAUGE SWITCHES ON/OFF INTERMITTENTLY. CAUSE: THESE ISSUES MAY BE CAUSED BY: LR4, RANGE ROVER SPORT ONLY: SOFTWARE ISSUE WITHIN THE INSTRUMENT CLUSTER (IC). BACKED-OUT PINS IN ANY OF THE FOLLOWING AREAS: INTERNAL TO THE FUEL TANK (SENDER WIRING), FUEL PUMP MODULE, AND/OR FUEL TANK FLANGE ASSEMBLY. FRETTING CORROSION ACROSS THE FUEL SENDER HARNESS PINS INSIDE THE FUEL TANK (BLACK CONNECTORS)."

THE VEHICLE SEAT MEMORY MODULE LOGS U1A4C 00, BUILD END OF LINE MODE ACTIVE CAUSE THE SEAT MODULE HAS BEEN INCORRECTLY CONFIGURED TO THE VEHICLE."

MODEL VEHICLES AFFECTED; LR4 2010-2013, LR2, RANGE ROVER SPORT 2010-2013, RANGE ROVER 2010-2012. *LJ

IN CERTAIN MODEL VEHICLES A POTENTIAL CONCERN RELATES TO THE FRONT DOOR HARNESS NOT BEING RETAINED DUE TO INCORRECTLY MANUFACTURED EDGE CLIPS. AS A CONSEQUENCE, THE HARNESS HAS THE POTENTIAL TO CHAFE ON THE INNER DOOR PANEL. *PE UPDATED 04/20/11 *PE

to respond or no functionality at all.

to respond or no functionality at all.

Range where the tailgate exterior release switch may display intermittent switching performance issues.

exterior release switch may display intermittent switching performance issues.

DIAGNOSTIC TROUBLE CODES (DTC) ARE STORED. CAUSE: THIS MAY BE CAUSED BY VARIOUS ISSUES."

WHICH IS NOT COMPATIBLE WITH LAND ROVER INFOTAINMENT SYSTEMS. CAUSE THIS IS TO MAKE YOU AWARE OF THE TYPES OF MEDIA THAT MAY CAUSE THE UNIT TO FAIL WITH THE CUSTOMER."

'HOOD OPEN' MESSAGE IS DISPLAYED ON THE INSTRUMENT CLUSTER; AND/OR A MISLOCK SOUND IS EMITTED WHEN LOCKING THE VEHICLE. CAUSE: THESE ISSUES MAY BE CAUSED BY A FAULTY HOOD OPEN SWITCH."

WHICH IS NOT COMPATIBLE WITH LAND ROVER INFOTAINMENT SYSTEMS. CAUSE THIS IS TO MAKE YOU AWARE OF THE TYPES OF MEDIA THAT MAY CAUSE THE UNIT TO FAIL WITH THE CUSTOMER. THEY ARE COPY CONTROL COMPACT DISCS (CCCD) RECORDABLE COMPACT DISCS (CD-R) REWRITABLE COMPACT DISCS (CD-RW) ECO DISCS, WHICH ARE VERY THIN, ONLY 0.6MM. PLEASE REFER TO ATTACHMENT FOR EXAMPLES OF DISCS THAT ARE KNOWN TO HAVE CAUSED DAMAGE."

CAUSE: SOFTWARE COMPATIBILITY ISSUES"

CAUSE: SOFTWARE COMPATIBILITY ISSUES ACTION: IF A CUSTOMER REPORTS THE CONCERN DETAILED ABOVE AN HLDF SOFTWARE UPDATE WILL BE REQUIRED USING SDD. TO COMPLETE THE UPDATE FOLLOW THE INSTRUCTIONS BELOW:-"

IT HAS BEEN SWITCHED OFF BY THE USER ACTION :- IF INVESTIGATING A CUSTOMER COMPLAINT OF NO GRIDLINES ON THE GRAPHICAL DISPLAY, THEN PLEASE FOLLOW THE INSTRUCTIONS DESCRIBED IN THE ATTACHMENT OR THE VEHICLE HANDBOOK."

CAUSE: SOFTWARE COMPATIBILITY ISSUES"

'HOOD OPEN' MESSAGE IS DISPLAYED ON THE INSTRUMENT CLUSTER; AND/OR A MISLOCK SOUND IS EMITTED WHEN LOCKING THE VEHICLE. CAUSE: THESE ISSUES MAY BE CAUSED BY A FAULTY HOOD OPEN SWITCH."

CAUSE: INCORRECT DIAGNOSIS."

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

ROUGH IDLE, HESITATION AND/OR LOSS OF POWER. ONE OR MORE OF THE FOLLOWING DTCS MAY BE SET IN THE PCM: P008A, P008B, P2542. CAUSE: SUB-OPTIMAL PCM SOFTWARE CALIBRATION"

INSTRUMENT CLUSTER: FAULTY GENERATOR FAULTY BATTERY MONITORING SYSTEM (BMS) THE CHARGE WARNING INDICATOR IS ILLUMINATED WHEN THE ENGINE IS RUNNING. CAUSE: THE POWER SUPPLY IS A FULLY INTEGRATED SYSTEM THAT REQUIRES SDD TO DIAGNOSE OVERALL FUNCTIONALITY ROBUSTLY TO MAKE SURE CUSTOMER SATISFACTION IS MET VIA RIGHT FIRST TIME DIAGNOSIS."

THEREFORE WOULD APPRECIATE MORE INFORMATION TO AID INVESTIGATIONS. KNOWN ISSUES HAVE BEEN RESOLVED AND ASSURED VINS FOR EFFECTED MODELS ARE: EVOQUE: H021033(15MY), H920134 (PUNE) DISCOVERY 4 A756425 FREELANDER2: H432120, H911856 (PUNE)"

INDUCTION / FUEL INJECTION CLEANING EQUIPMENT OR MATERIALS. THIS INCLUDES, BUT IS NOT LIMITED TO, ""VACU-FLUSH"" TYPE EQUIPMENT. CAUSE: THE USE OF NON-APPROVED EQUIPMENT CAN CAUSE THE ENGINES TO HYDRO-LOCK, OR CAUSE OTHER ENGINE DAMAGE, AND SOMETIMES THE ONLY POSSIBLE REPAIR IS TO REPLACE THE ENGINE."

WARRANTY DATA INDICATES A VOLUME OF FUEL INJECTORS BEING REPLACED IN RELATION TO THE SYMPTOM OUTLINED BELOW: VEHICLES SUFFERING FROM A MISFIRE AT COLD START AND ON SOME OCCASIONS INTERMITTENT ROUGH RUNNING AT NORMAL OPERATING TEMPERATURE, WITH VARIOUS DTC'S STORED SUCH AS P0300-00 P0301-00 P0302-00 P0304-00 P1315-00 P0316-00 CAUSE: ENGINEERING WOULD LIKE TO GAIN FURTHER UNDERSTANDING INTO THE CAUSE OF THESE FUEL INJECTOR FAILURES."

ROVER / RANGE ROVER VEHICLES IN WARRANTY. CAUSE: UNKNOWN ENGINEERING INVESTIGATION ON-GOING."

WITH RELATED DTCS C2007-11 OR C2008-11. CAUSE: JLR ENGINEERING ARE CONTINUING TO INVESTIGATE ROOT CAUSE OF THE ISSUE."

ISSUES WITH RELATED DTCS C2007-11 OR C2008-11. CAUSE: JLR ENGINEERING ARE CONTINUING TO INVESTIGATE ROOT CAUSE OF THE ISSUE."

TROUBLE CODE (DTC) P1889-14 OR P0961-62 MAY BE STORED IN THE REAR DIFFERENTIAL CONTROL MODULE (RDCM). NOTE: ANY REPAIRS OTHER THAN CONFIGURING THE REAR DIFFERENTIAL CONTROL MODULE (RDCM) MUST BE CARRIED OUT AS A SEPARATE CLAIM. CAUSE: THIS MAY BE CAUSED BY THE REAR DIFFERENTIAL CONTROL MODULE (RDCM) DIAGNOSTIC FUNCTION BEING TOO SENSITIVE, LEADING TO THE FALSE DETECTION OF OPEN CIRCUITS OR STICKING VALVES IN THE ACTIVE ON-DEMAND COUPLING ASSEMBLY."

CAUSE: WHEN CHARGING A BATTERY (BOTH PRIMARY AND SECONDARY) WITH A BMS (BATTERY MONITORING SYSTEM) FITTED, THE EARTH FROM THE CHARGER MUST BE CONNECTED TO A SUITABLE CHASSIS OR ENGINE EARTH (CHECK TOPIX FOR APPROPRIATE LOCATION). THIS ALLOWS THE BMS TO SEE THE CURRENT GOING INTO THE BATTERY. HOWEVER WHEN USING A DIAGNOSTIC CHARGER FROM MIDTRONICS SUCH AS GR1, GRX GR8(110 VOLTS)THIS CONNECTION PROCESS CAN CAUSE AN INCORRECT BATTERY ANALYSIS DUE TO THE EXTRA RESISTANCE IN THE WIRING WHEN CONNECTED TO A CHASSIS OR ENGINE EARTH."

CAUSE: LAND ROVER ENGINEERING HAVE RECENTLY VISITED DEALERSHIPS WHERE A REQUEST HAS BEEN MADE TO REPLACE THE STEERING GEAR FOR AN OIL LEAK IN THE AREA OF THE PINION HOUSING, CASTING, YOKE PLUG OR THE GAITER ADJACENT TO THE PINION HOUSING. FOLLOWING INVESTIGATION THE SOURCE OF THE LEAK PATH WAS IDENTIFIED AS BEING FROM THE SUPPLY AND RETURN HOSE O-RING SEALS."

BY WELD SPLATTER CONTAMINATION IN STEERING GEAR PISTON TUBE. *PE

A POTENTIAL CONCERN HAS BEEN IDENTIFIED WITH A NUMBER OF VEHICLES REGARDING A COOLANT LEAK FROM THE QUICK CONNECTOR JOINT SECURING A VENT HOSE TO THE ENGINE. *PE

AN ISSUE HAS BEEN IDENTIFIED WHERE THE FUEL GAUGE MAY READ FULL WHEN TURNING THE IGNITION ON AND RETURN TO NORMAL OPERATION SHORTLY AFTER STARTING THE ENGINE. THIS MAY BE CAUSED BY A SOFTWARE ISSUE WITHIN THE CENTRAL JUNCTION BOX (CJB). *PE

CAUSE: PART SUPPLY CONSTRAINTS."

CAUSE: THIS MAY BE CAUSED BY A TOLERANCE STACK-UP BETWEEN THE DOOR MIRROR AND THE DOOR AND/OR THE RETAINING SCREWS MAY BE LOOSE/UNDER TORQUED."

CAUSE: OIL FILTER LR001247 SUPERSEEDS TO LR030778 WHICH IS SUPPLIED WITH A NEW SEAL. THIS SEAL IS SLIGHTLY LARGER IN DIAMETER THAN THE ONE SUPPLIED WITH LR001247"

CAUSE: A NEW PART AND PART NUMBER ARE AVAILABLE."

CAUSE: THIS MAY BE CAUSED BY A TOLERANCE STACK-UP BETWEEN THE DOOR MIRROR AND THE DOOR AND/OR THE RETAINING SCREWS MAY BE LOOSE/UNDER TORQUED."

CAUSE: THIS MAY BE CAUSED BY A BUILD-UP OF DIRT AND GREASE ON THE SURFACE OF THE WINDSHIELD GLASS."

CAUSE: THIS MAY BE CAUSED BY WATER PASSING THROUGH THE HIGH-MOUNTED STOP LAMP SEAL."

ISSUE: THE PRIMARY DOOR SEALS COME ADRIFT FROM THE BODY AT THE BOTTOM OF THE DOOR APERTURE. CAUSE: THE CAUSE IS BEING INVESTIGATED AND INFORMATION IS REQUIRED TO HELP ESTABLISH ROOT CAUSE."

CAUSE: THE CAUSE IS BEING INVESTIGATED AND INFORMATIONIS REQUIRED TO HELP ESTABLISH ROOT CAUSE."

THE VEHICLE CAUSE: THE CAUSE OF THE PARTS COMING ADRIFT IS UNDER INVESTIGATION BUT AS THE PARTS ARE A ONE TIME FIT ITEM REFITTING THEM USING ADHESIVE OR DOUBLE SIDED TAPE WILL NOT WORK"

THE LAMP SEAL CAUSES WATER TO PASS THROUGH. *PE

THE DOORS MAY NOT OPEN FROM EITHER SIDE OR MAY NOT LOCK. *RM

*PE

UPON INSPECTION, LOW PRESSURE IS RECORDED ON THE HIGH PRESSURE SYSTEM, HIGH PRESSURE IS RECORDED ON THE LOW PRESSURE SYSTEM, AND THE COMPRESSOR CLUTCH (WHERE APPLICABLE) IS WORKING PROPERLY.

UPON DIAGNOSIS, DIAGNOSTIC TROUBLE CODE (DTC) P1889-14 IS FOUND TO BE STORED. CAUSE: THIS MAY BE CAUSED BY INSUFFICIENT SPRING LOAD FOR COMMUTATOR BAR BRUSHES IN THE ACTIVE ON-DEMAND COUPLING OIL PUMP."

BUTTON MECHANISM HAS BEEN MODIFIED TO PREVENT THIS ISSUE FROM VIN NO. H372254 UK BUILD L910950 PUNE BUILD"

BUTTON MECHANISM HAS BEEN MODIFIED TO PREVENT THIS ISSUE FROM VIN NO. H372254 UK BUILD L910950 PUNE BUILD ACTION: TO RESOLVE THIS ISSUE PLEASE REPLACE THE GEAR SELECTOR KNOB ONLY

CAUSE: OIL OR GREASE LEAK PAST INPUT SHAFT SEAL THROUGH NORMAL USE OR SEAL FAILURE."

BUTTON MECHANISM HAS BEEN MODIFIED TO PREVENT THIS ISSUE FROM VIN NO. H372254 UK BUILD L910950 PUNE BUILD"

2/LR2 PRODUCTS, DEALERS HAVE BEEN REPLACING COMPLETE STEERING GEAR ASSEMBLIES. CAUSE: PREVIOUSLY, THE INNER BALL JOINTS WERE NOT AVAILABLE AS SEPARATE LOWER LEVEL REPAIR ITEMS THROUGH MICROCAT."

DIFFERENTIAL CONTROL MODULE (RDCM), ON SOME VEHICLES. MODEL 2009-2011 LR2. *PE

HALOGEN BULB - LR044458. CAUSE: LTB00841 HAS BEEN TEMPORARILY REMOVED FROM TOPIX IN ORDER TO PROCURE SUFFICIENT PARTS FROM JLR SUPPLIERS - PARTS ARE DUE TO BE MADE AVAILABLE TO MARKETS IN WEEK 4 OF 2016, UPON WHICH, THE BULLETIN WILL BE RELEASED FOR PUBLICATION."

HALOGEN BULB - LR044458. CAUSE: LTB00841 HAS BEEN TEMPORARILY REMOVED FROM TOPIX IN ORDER TO PROCURE SUFFICIENT PARTS FROM JLR SUPPLIERS."

CAUSE: THIS MAY LEAD TO EARLIER THAN EXPECTED BULB REPLACEMENT."

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES"

CAUSE: DAMAGE/MARKING CAUSED BY OBJECT IMPACT AGAINST THE LENS. STAINING/DISCOLORATION CONTAMINATION CAUSED BY USING ANY TYPE OF CLEANING PRODUCT ON LENS. IMPORTANT: OWNERS HANDBOOK SPECIFIES TO CLEAN WITH A LIGHTLY MOISTENED CLOTH AND DO NOT USE CHEMICAL AGENTS OR DOMESTIC CLEANERS ACTION WHERE A CUSTOMER CONCERN IS REPORTED, PLEASE ORDER THE LENS KIT FOR THE RELEVANT MODEL"

CAUSE: CONDENSATION/MIST IS A NATURAL PHENOMENON WHICH CAN OCCUR WHEN THERE IS A TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND OUTSIDE OF THE LAMP UNIT. THIS CONDENSATION IS CONSIDERED TO BE AS A RESULT OF NORMAL ATMOSPHERIC CONDITIONS AND REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM. WITH THE INTRODUCTION OF CLEAR LENSES CONDENSATION IS LIKELY TO BE MORE NOTICEABLE BUT DOES NOT AFFECT THE PERFORMANCE OF THE LAMP. CONDENSATION WILL CLEAR WHEN THE LIGHTS HAVE BEEN ON FOR SOME LENGTH OF TIME AND IN WARMER AMBIENT TEMPERATURES."

VEHICLE WOULD NOT LOSE POWER. *PE

*PE

BE FOUND WITHIN THE POWER STEERING FLUID SYSTEM WHICH COULD LEAD TO SYSTEM CONTAMINATION AND A DETERIORATION IN SYSTEM PERFORMANCE. CAUSE: INTERNAL DEBRIS FROM A SUSPECTED COMPONENT MALFUNCTION MAY RESULT IN THE POWER STEERING FLUID BECOMING CONTAMINATED."

ACTION: WHEN DIAGNOSING CUSTOMER CONCERNS RELATING TO THE HYDRAULIC POWER STEERING SYSTEM, REFER TO THE SERVICE INFORMATION BELOW."

THE ISSUE IS COMMON ACROSS ALL MANUFACTURERS SYMPTOMS WHEN THE APPLE DEVICE IS CONNECTED TO THE CAR SYSTEM AND A CALL IS RECEIVED THERE IS NO OPTION TO ANSWER OR REJECT THE INCOMING CALL ON THE SYSTEM. THE STEERING WHEEL CONTROLS ALSO HAVE NO EFFECT. THE TOUCH SCREEN CONTINUES TO DISPLAY THE PHONE SCREEN. THE POP-UP SCREEN TO ANSWER OR REJECT THE CALL IS NOT SHOWN."

CAUSE: THIS MAY BE CAUSED BY A ROAD WHEEL/TIRE ASSEMBLY IMBALANCE AND/OR TEMPORARY TIRE FLAT-SPOTTING.

THE AIR BAGS MAY INADVERTENTLY DISABLE. *RM

LR2 MODELS. *RM UPDATED 11/18/11. *PE

INSTRUMENT PACK EVEN THOUGH THE HOOD / BONNET IS CLOSED CAUSE: THERE IS A POTENTIAL THAT AN INTERNAL SPRING COULD BECOME DISLODGED"

THE ISSUE IS IDENTIFIED AS A CLICK NOISE FROM A FRONT DRIVE SHAFT (HALF SHAFT). CAUSE: SMALL AMOUNT OF MOVEMENT OF THE SPLINES OF THE SHAFT WITHIN THE HUB."

THE AIR BAG CLOCKSPRING CONNECTOR MAY BECOME DISCONNECTED AND COULD RESULT IN AIR BAGS NOT DEPLOYING IN AN ACCIDENT. *RM

(SEE FIG.1) ACTION: REPLACE BY PRESSING ON NEW BUTTON CAP PART NO: LR045801 (SEE FIG.2)"

OUTSIDE THE VIN RANGE IN THE BULLETIN. THERE IS ALSO EVIDENCE THAT THE BULLETIN HAS BEEN COMPLETED ON EVOQUE. SPECIAL SERVICE MESSAGES 46477, 54417 AND 55837 ALSO REFER TOLTB00342. ACTION: THE REPAIR OUTLINED IN LTB00342 (CURRENTLY AT VERSION 2) MUST ONLY BE COMPLETED ON FREELANDER 2 (LR2) WITHIN THE BULLETIN VIN RANGE 000212 TO 257090. AT VIN 257091 AN IMPROVED PINION BEARING DESIGN WAS INTRODUCED ALONG WITH A DESIGN CHANGE TO THE DIFFERENTIAL."

*RM

CAUSE: DAMAGE TO THE CALIPER FINISH WHILE CLEANING THE VEHICLE AND, OR THE ROAD WHEELS"

MODEL LR2, RANGE ROVER EVOQUE. NO MODEL YEAR. *PE UPDATE 12/6/13. *PE

(blowing warm and then cold); ? Windshield, rear window, and/or door windows mist up in cool (15C or lower) ambient temperatures; ? Poor cooling performance of the Air Conditioning (A/C) system; and/or ? Warm, damp or musty smells coming from the vents.

HALEWOOD BUILT VEHICLES ONLY - IDENTIFIED BY THE 11TH DIGIT OF THE VIN = 'H' FREELANDER 2 (L359) VEHICLES VIN: ALL EVOQUE (L538) VEHICLES UPTO VIN: H991051. PUNE BUILT VEHICLES ONLY - IDENTIFIED BY THE 11TH DIGIT OF THE VIN = 'L') FREELANDER (L359) VEHICLES VIN: ALL EVOQUE (L538) VEHICLES VIN: N/A (NOT AFFECTED)"