2014 Kia Sportage TSBs

(CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

advising that Kia is conducting Customer Satisfaction Campaign. Kia has developed a new zinc-reinforced ignition cylinder protector hardware upgrade and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Prior notifications stated that this modification had to be performed by July 1, 2025, but the subject vehicles are now eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 19, 2025 through December 31, 2025)

is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)

(CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement"; equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

an additional vehicle modification available for installation to help deter or thwart attempted thefts. This modification consists of a theft deterrent ignition cylinder protector and will be available to you free of charge for eighteen (18) months from the date of this letter.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

(CS2311) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 13, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

developed a software upgrade that can be installed on your vehicle free of charge to restrict the operation of the vehicle's ignition system should your locked vehicle be the subject of a break-in and theft attempt without the key. However, the previous letter was sent in error. The customer's vehicles are equipped with an electronic engine immobilizer and are NOT equipped with a steel key and "turn-to-start" ignition system, and they are not targeted for theft by the social media challenge and does not require a software upgrade. As a result, customers may disregard that letter.

test procedure of the Bearing Clearance Tester (BCT) Special Service Tool (SST). The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.

to address a no-start or hard start with poor running condition after engine replacement under PI1802Y/Z or PI1803Y/Z. Some replacement long blocks may come with pre-installed fuel rail, injectors, and injector wiring harness. If the condition is present, it is possible that the injector harness was not installed correctly. The connections may be swapped from cylinder No. 1 and cylinder No. 4, and from cylinder No. 2 and cylinder No. 3.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled Knock Sensor Detection System - ECU Logic Improvement equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

revised to include additional information. - This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement".

revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement".

been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

- SUPERSEDED BY PI1802YZ/1803YZ.

revised to include additional information.This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1803, Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

BY PI1802Y/Z.

update the emission related logic of the Engine Control Module (ECM) with an improved version on some 2014-2016MY Sportage (SL) vehicles equipped with Theta 2.4L GDI SULEV engines, produced from September 30, 2013 through November 16, 2015 to ensure compliance with emission regulations. To correct this condition, apply the improved logic to the ECM using the KDS ECU Upgrade function as described in this bulletin.

in the engine compartment of the vehicle once the Emissions Service Campaign has been completed on vehicles registered in one of the S.177 States of Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington

answer guide related to the a Voluntary Emissions Service Campaign on certain 2014-2016 MY Kia Sportage vehicles equipped with the 2.4-Liter GDI SULEV engine, to update the emission related logic of the Engine Control Module (ECM) with an improved version to ensure compliance with emissions regulations.

to advise the dealer service managers that Kia is conducting a Voluntary Emissions Service Campaign on certain 2014-2016 MY Kia Sportage vehicles equipped with the 2.4-Liter GDI SULEV engine, to update the emission related logic of the Engine Control Module (ECM) with an improved version to ensure compliance with emissions regulations.

advise the dealer principals that Kia is conducting a Voluntary Emissions Service Campaign on certain 2014-2016 MY Kia Sportage vehicles equipped with the 2.4-Liter GDI SULEV engine, to update the emission related logic of the Engine Control Module (ECM) with an improved version to ensure compliance with emissions regulations.

INSTALLATION (SC184) - This bulletin provides the procedure to inspect the evaporative system's existing canister for noise caused by loose charcoal on some 2011-2016 MY Sportage (SL) vehicles equipped with the 2.4L ULEV engine produced from May 6, 2010 through November 16, 2015. If noise caused by loose charcoal is confirmed, to improve evaporative system performance, follow the procedure set forth below on how to install the auxiliary canister kit.

for the Voluntary Emissions Service Campaign to inspect the evaporative canister and, if necessary, install an Auxiliary Canister Kit to improve evaporative system performance on certain 2011-2016 MY Kia Sportage vehicles equipped with the 2.4-liter ULEV engine and manufactured from May 6, 2010 through November 16, 2015.

announce a new Voluntary Emissions Service Campaign to inspect the evaporative canister and, if necessary, install an Auxiliary Canister Kit to improve evaporative system performance on certain 2011-2016 MY Kia Sportage vehicles equipped with the 2.4-liter ULEV engine and manufactured from May 6, 2010 through November 16, 2015.

Voluntary Emissions Service Campaign to inspect the evaporative canister and, if necessary, install an Auxiliary Canister Kit to improve evaporative system performance on certain 2011-2016 MY Kia Sportage vehicles equipped with the 2.4-liter ULEV engine and manufactured from May 6, 2010 through November 16, 2015.

revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled Knock Sensor Detection System - ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

to include additional information.This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC), P1326.

is conducting an important Product Improvement Campaign to perform a software update on all 2014-2018 MY Sportage vehicles equipped with 2.4L Gasoline Direct Injection ("GDI") and 2.0L Turbocharged GDI ("T-GDI") engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").

bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled '"Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

the partial repair of the Four Wheel Drive (4WD) Coupling Assembly, Pressure Sensor, Actuator Motor or 4WD harness on some 2011-2020 Sportage (SL, QL) and 2013-2020MY Sorento (XMa, UMa) 4WD vehicles for a concern regarding: Oil leakage from the 4WD coupling assembly 4WD Malfunction and MIL lamp ON with DTCs Abnormal noise or vibration while driving

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage. The KSDS detects vibrations indicating the onset of excessive connecting rod bearing wear. It is designed to alert the driver at an early stage of bearing wear before the occurrence of severe engine damage, including engine failure. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Limp Home Mode. This will reduce further damage to the engine and ensure that the vehicle occupants are not exposed to the risk of a more severe engine failure. At that time, Diagnostic Trouble Code (DTC) P1326, specific to the KSDS, will be recorded in the ECU. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed. Also, engine RPMs will be limited to approximately 1800-2000 RPM.

is conducting an important Product Improvement Campaign to perform a software update on all 2014-2018 MY Sportage vehicles equipped with 2.4L Gasoline Direct Injection ("GDI") and 2.0L Turbocharged GDI ("T-GDI") engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").

related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.

related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.

Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

to include additional information This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326..

to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 5, 12/20/2018) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.

revised to include additional information.This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

This bulletin provides information relating to all Kia vehicles equipped with Gasoline Direct Injection (GDI) engines. In these engines highly pressurized gasoline is injected via a common fuel rail and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional Multi-Point Fuel Injection (MPI) engine, the gasoline is injected into the intake port of each cylinder at a relatively low pressure. Due to high fuel pressure in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specifications for the GDI fuel system components.

This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage

has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage

This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 2, 09/24/2018) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.

provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 2, 09/24/2018) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.

25, 2018 to perform a software update on certain vehicles with 2.4L GDI engines to alert vehicle drivers at an early stage of bearing wear to prevent severe engine damage.

bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage. This update is for: * Some 2014MY Optima (TF) vehicles equipped with 2.4L GDI engines, manufactured at KMC from August 29, 2013 through April 25, 2014; * All 2015MY Optima (TF/QF) vehicles equipped with 2.4L GDI and 2.0L Turbocharged GDI (T-GDI) engines; * All 2014-2015MY Sportage (SL) vehicles equipped with 2.4L GDI and 2.0L Turbocharged GDI (T-GDI) engines; * All 2015MY Sorento (XMa) vehicles equipped with 2.4L GDI engines, manufactured from January 3, 2014 through December 11, 2014. The KSDS detects vibrations indicating the onset of excessive connecting rod bearing wear. It is designed to alert the driver at an early stage of bearing wear before the occurrence of severe engine damage, including engine failure. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Limp Home Mode. This will reduce further damage to the engine and ensure that the vehicle occupants are not exposed to the risk of a more severe engine failure. At that time, Diagnostic Trouble Code (?DTC?) P1326, specific to the KSDS, will be recorded in the ECU. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed. Also, engine RPMs will be limited to approximately 1800-2000 RPM. Kia is requesting the completion of this Product Improvement Campaign on all affected vehicles.

is conducting an important Product Improvement Campaign to perform a software update on all 2014-2015 MY Sportage vehicles equipped with 2.4L Gasoline Direct Injection (?GDI?) and 2.0L Turbocharged GDI (?T-GDI?) engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (?ECU?).

update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

considered serviceable, and should be thoroughly cleaned and transferred to the new engine.

turbo oil feed line on some 2011-2015MY Optima (TF), produced from November 1, 2010 through August 30, 2011, 2012-2015MY Optima (QF), produced from August 31, 2011 through October 2, 2015, and 2011-2015MY Sportage (SL) vehicles, produced from December 30, 2010 through November 6, 2015, equipped with Theta 2.0T-GDI engine, which may exhibit an oil leak at the turbo oil feed line.

this bulletin is to provide information related to the extension of the New Vehicle Limited Warranty for the Engine Short Block Assembly (engine block, crankshaft and bearings, connecting rods and bearings and pistons) on certain 2014 MY Sportage vehicles with 2.4L GDI or 2.0L Turbo GDI engine to 10 years starting from the date of first service or 120,000 miles whichever occurs first, regardless of whether the vehicle owner is an original or subsequent vehicle owner.

will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.

will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.

for some 2012~2015MY Optima (QF) vehicles, produced from August 12, 2011 to October 2, 2015, some 2012~2015MY Sorento (XMa) vehicles, produced from April 19, 2011 to December 11, 2014, some 2011~2015MY Optima (TF) vehicles, produced from August 12, 2010 to July 23, 2015, and some 2014~2016MY Sportage (SL) vehicles, produced from September 30, 2013 to November 16, 2015, which may experience a malfunction indicator lamp (MIL) illuminated with the Electronic Control Unit (ECU) system-related DTC(s): P0420 and possibly P0171. This concern occurs most commonly during prolonged engine braking while descending a steep grade.

return lines.

for some 2012~2015MY Optima (QF) vehicles, produced from August 12, 2011 to October 2, 2015, some 2012~2015MY Sorento (XMa) vehicles, produced from April 19, 2011 to December 11, 2014, some 2011~2015MY Optima (TF) vehicles, produced from August 12, 2010 to July 23, 2015, and some 2014~2016MY Sportage (SL) vehicles, produced from September 30, 2013 to November 16, 2015, which may experience a malfunction indicator lamp (MIL) illuminated with the Electronic Control Unit (ECU) system-related DTC(s): P0420 and possibly P0171. This concern occurs most commonly during prolonged engine braking while descending a steep grade.

with a 2.4L GDI engine, it is important to note that the DTC may recur after replacement of any faulty component(s) and resetting adaptive values. See this Article for information on resetting cylinder balance adaptation values.

system is the placement of each fuel injector directly into the engine cylinder head assembly. Therefore, it is completely normal for the combustion process to create deposits on the injector spray tip surfaces.

SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.

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

PROGRAM - IF YOU HAVE PAID TO HAVE YOUR ENGINE REPAIRED/REPLACED DUE TO CONNECTING ROD FAILURE, YOU MAY BE ELIGIBLE FOR REIMBURSEMENT FOR SOME OR ALL OF THAT EXPENSE. MAIL THIS COMPLETED REQUEST FOR REIMBURSEMENT FORM TO KIA, ALONG WITH DOCUMENTATION SPECIFIED BELOW, FOR REVIEW AND CONSIDERATION TO THE FOLLOWING ADDRESS: CONSUMER ASSISTANCE CENTER, KIA MOTORS AMERICA, INC., P.O. BOX 52410, IRVINE, CA 92619-2410, 1-800-333-4542

IMMEDIATELY, KIA MOTORS AMERICA, INC. HAS EXTENDED THE WARRANTY COVERAGE OF THE KIA NEW VEHICLE LIMITED WARRANTY FOR THE SHORT BLOCK ASSEMBLY (ENGINE BLOCK, CRANKSHAFT AND BEARINGS, CONNECTING RODS AND BEARINGS AND PISTONS) ON 2011-2014 MY SPORTAGE 2.0L TURBO GDI AND 2.4L GDI ENGINE TO 10 YEARS STARTING FROM THE DATE OF FIRST SERVICE OR 120,000 MILES, WHICHEVER COMES FIRST, REGARDLESS OF WHETHER THE VEHICLE OWNER IS AN ORIGINAL OR SUBSEQUENT VEHICLE OWNER. THE PURPOSE OF THIS WARRANTY EXTENSION IS TO ADDRESS ISSUES WITH CONNECTING ROD AND BEARING WEAR THAT CAN LEAD TO ENGINE FAILURE."

WHICH MONITORS AND PREVENTS THE SIMULTANEOUS ACTIVATION OF ACCELERATOR AND BRAKE PEDALS. WHEN ENGAGED, THE FEATURE REDUCES ENGINE POWER TO IDLE. MOST CUSTOMERS WILL NEVER NOTICE THE SMART PEDAL FEATURE WHEN ACTIVE, HOWEVER, CUSTOMERS WHO TEND TO REST THEIR FOOT ON THE BRAKE PEDAL WHILE DRIVING MIGHT DESCRIBE A HESITATION OR DELAY SYMPTOM AND NOT REALIZE THAT THE EMS ELECTRONIC CONTROL MODULE IS INTERVENING, AS DESIGNED.

PROPER ENGINE OIL GRADE / VISCOSITY TO BE USED WHEN SERVICING VEHICLES EQUIPPED WITH A TURBOCHARGER. IN ADDITION TO FOLLOWING THE TURBO-SPECIFIC MAINTENANCE INTERVAL SCHEDULES, IT IS VERY IMPORTANT TO FOLLOW THE GRADE AND THE SAE OIL VISCOSITY RECOMMENDATIONS IN THE APPLICABLE SERVICE MANUAL TO ENSURE THE PROPER LUBRICATION IS DELIVERED TO THE TURBOCHARGER AND TO PREVENT ENGINE DAMAGE.

MODEL ALL. NO YEARS LISTED. *PE

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure for upgrading the UVO system on some 2014~2016MY Soul (PS), Sorento (XMa), Optima (TF/QF), Forte (YD) and Sportage (SL) vehicles to address "Incoming ring volume too loud" complaints when using certain smartphones (non-iPhone). Additionally, in 2014MY vehicles the upgrade will also improve Bluetooth connectivity and voice recognition.

identify and record the head unit software level on various head unit platforms and generations.

(ELE091) (Rev 1) - This bulletin provides the procedure on how to identify and record the head unit software level on various head unit platforms and generations. This procedure will now be required when ordering head units through the Direct Exchange Program (see Parts Bulletin 91-961-0005).

2014MY Soul (PS), Sorento (XMa), Optima (TF, QF), Forte (YD), Sportage (SL), and Rio (UB) vehicles, to improve Bluetooth connectivity, Phonebook Download, Audio Streaming and Call History Download.

Sorento (XMa)/(UMa), Optima (TF HEV), Forte (YD), Sportage (SL), 2015-2016MY Sedona (YP), and 2014-2015(MY) Optima (QF/TF) vehicles to address ?Incoming ring volume too loud? complaints when using certain smartphones (non-iPhone). Additionally, in 2014MY vehicles the upgrade will also improve Bluetooth connectivity and Voice Recognition (VR).

Navigation software on some Sportage (SL), Cadenza (VG), Optima (QF/TF), and Optima (TF HEV) vehicles, which may experience an inactive (grayed out) Sirius Traffic icon, no traffic flow shown, or a ?There is no traffic on route.? message.

ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.

COMPATIBILITY ISSUES BETWEEN NAVIGATION HEAD UNITS AND SD CARDS WHEN REPLACING HEAD UNITS FOR MULTIMEDIA ISSUES. IF AFTER REPLACING A NAVIGATION HEAD UNIT THE ORIGINAL SD CARD DOES NOT OPERATE CORRECTLY, FOLLOW THE STEPS BELOW TO DIAGNOSE THE ISSUE:

BLUETOOTH CONCERNS WHEN USING AN IPHONE WITH IOS 8.X (IOS 8, 8.0.1, 8.0.2, 8.1, 8.1.2, 8.1.3, ETC.) WHILE PAIRED TO A HEAD UNIT.

(TF/QF), FORTE (YD) AND SPORTAGE (SL) VEHICLES TO IMPROVE BLUETOOTH CONNECTIVITY, VOICE RECOGNITION, AND TO IMPROVE "INCOMING RING VOLUME TOO LOUD" COMPLAINTS ON CERTAIN SMARTPHONES (NON-IPHONE).

(TF/QF), SORENTO (XMA), SPORTAGE (SL), RIO (UB), AND FORTE (YD) VEHICLES TO IMPROVE BLUETOOTH CONNECTIVITY, PHONEBOOK DOWNLOAD, AUDIO STREAMING, AND CALL HISTORY DOWNLOAD.

CUSTOMER COMPLAINTS ON NAVIGATION HEAD UNITS (AVN 3.0 OR AVN 3.5): * KOREAN ERROR MESSAGE THAT STARTS WITH NAVI.EXE OR * KOREAN ERROR MESSAGE THAT STARTS WITH MMMEDIA.EXE.

ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.

THAT HAVE A SPECIFIC ERROR DISPLAYED ON THE NAVIGATION HEAD UNIT (SHOWN BELOW) AFTER PURCHASING AND INSTALLING A VERSION 8.5 MAP UPDATE SD CARD. A TOTAL OF 129 AFFECTED SD CARDS WERE PURCHASED BY CUSTOMERS THROUGH KIA DEALERS, FROM JANUARY 1ST TO MAY 11TH, 2015.

THE BASE AUDIO SYSTEM SOFTWARE OF SOME 2014MY SOUL (PS), OPTIMA (TF/QF), SORENTO (XMA), SPORTAGE (SL), RIO (UB), AND FORTE (YD) VEHICLES, TO IMPROVE BLUETOOTH CONNECTIVITY, PHONEBOOK DOWNLOAD, AUDIO STREAMING AND CALL HISTORY DOWNLOAD. FOR VEHICLES NOT ON THE AFFECTED VEHICLES LIST, BUT WITH A CUSTOMER CONCERN AS DESCRIBED ABOVE, PERFORM THE FOLLOWING PROCEDURE OUTLINED IN THIS BULLETIN AND SUBMIT A WARRANTY CLAIM PER ""CUSTOMER CONCERN"" (STANDARD TSB) CLAIM INFORMATION ON PAGE 11. "

RECORD THE HEAD UNIT SOFTWARE LEVEL ON VARIOUS HEAD UNIT PLATFORMS AND GENERATIONS. THIS PROCEDURE WILL NOW BE REQUIRED WHEN ORDERING HEAD UNITS THROUGH THE DIRECT EXCHANGE PROGRAM.

UVO SYSTEM ON SOME 2014~2016MY SOUL (PS), SORENTO (XMA)/(UMA), OPTIMA (TF HEV), FORTE (YD), SPORTAGE (SL) 2015~2016MY SEDONA (YP), AND 2014-2015(MY) OPTIMA (QT/TF) VEHICLES TO ADDRESS INCOMING RING VOLUME TOO LOUD COMPLAINTS WHEN USING CERTAIN SMARTPHONES (NON-IPHONE). ADDITIONALLY, IN 2014MY VEHICLES THE UPGRADE WILL ALSO IMPROVE BLUETOOTH CONNECTIVITY AND VOICE RECOGNITION (VR). FOR VEHICLES NOT ON THE AFFECTED VEHICLES LIST, BUT WITH A CUSTOMER CONCERN AS DESCRIBED ABOVE, PERFORM THE FOLLOWING PROCEDURE OUTLINED IN THIS BULLETIN AND SUBMIT A WARRANTY CLAIM PER "CUSTOMER CONCERN" (STANDARD TSB) CLAIM INFORMATION ON PAGE 10.

OF THE SHARK-FIN STYLE ROOF ANTENNA OF SOME 2014~2015MY SPORTAGE (SL) VEHICLES, PRODUCED FROM AUGUST 1, 2014 THROUGH AUGUST 31, 2015, WHICH MAY EXHIBIT SIRIUS AUDIO RECEPTION CONCERNS (SEE SAMPLE COMPLAINTS BELOW). FOLLOW THE PROCEDURE OUTLINED IN THIS BULLETIN TO REPLACE THE ROOF ANTENNA AND CORRECT THE CONCERN.

REPLACEMENT OF THE SHARK-FIN STYLE ROOF ANTENNA OF SOME 2014~2016MY SPORTAGE (SL) VEHICLES, PRODUCED FROM AUGUST 1, 2014 THROUGH AUGUST 31, 2015, AND SOME 2014~2015MY OPTIMA (QF) VEHICLES, PRODUCED FROM AUGUST 1, 2013 THROUGH AUGUST 22, 2015, WHICH MAY EXHIBIT SIRIUS AUDIO RECEPTION CONCERNS (SEE SAMPLE COMPLAINTS BELOW). FOLLOW THE PROCEDURE OUTLINED IN THIS BULLETIN TO REPLACE THE ROOF ANTENNA AND CORRECT THE CONCERN.

UVO SYSTEM ON SOME 2014~2016MY SOUL (PS), SORENTO (XMA), OPTIMA (TF/QF), FORTE (YD) AND SPORTAGE (SL) VEHICLES TO ADDRESS INCOMING RING VOLUME TOO LOUD COMPLAINTS WHEN USING CERTAIN SMARTPHONES (NON-IPHONE). ADDITIONALLY, IN 2014MY VEHICLES THE UPGRADE WILL ALSO IMPROVE BLUETOOTH CONNECTIVITY AND VOICE RECOGNITION. FOR VEHICLES NOT ON THE AFFECTED VEHICLES LIST, BUT WITH A CUSTOMER CONCERN AS DESCRIBED ABOVE, PERFORM THE FOLLOWING PROCEDURE OUTLINED IN THIS BULLETIN AND SUBMIT A WARRANTY CLAIM PER "CUSTOMER CONCERN" (STANDARD TSB) CLAIM INFORMATION ON PAGE 10.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from December 10, 2015 through December 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from Dec 10, 2015 through Dec 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from Dec 10, 2015 through Dec 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from Dec 10, 2015 through Dec 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from Dec 10, 2015 through Dec 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2011-2016MY Sportage (SL) vehicles produced from May 6, 2010 through Nov 16, 2015, and 2017-2022MY Sportage (QL) vehicles produced from Dec 10, 2015 through Dec 7, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

USB ports and 12V power outlets to connect/charge mobile phones. Customers may experience issues with their head units that may be related to the use of aftermarket USB charging cables, including; * Electrical interference and limited or no functionality when attempting to play music, or when charging a device through the USB port * Excessive static or noise when listening to the audio source * Malfunctions and screen freeze of the head unit screen * Slow down of the system response while device is plugged in * Music will not play from iPhone 5 or 6 with Kia iPod cable and aftermarket adapter * No or limited functionality when trying to play music from an Apple device

The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.

VEHICLES, PRODUCED FROM SEPTEMBER 1, 2013 THROUGH JULY 1, 2014, WHICH MAY EXHIBIT A TPMS LIGHT ILLUMINATED IN THE CLUSTER, ALONG WITH DTC C1212 - VEHICLE SPEED SENSOR. TO CORRECT THIS CONCERN, REPLACE ALL FOUR (4) TPMS SENSORS WITH THE IMPROVED PARTS, BY FOLLOWING THE PROCEDURE OUTLINED IN THIS BULLETIN.

RELATED TO THE ECM SOFTWARE UPGRADE OF SOME 2014~2015MY FORTE (YD), PRODUCED FROM DECEMBER 7, 2013 TO APRIL 16, 2015, AND SOME 2014MY SPORTAGE (SL) VEHICLES, PRODUCED FROM APRIL 4, 2013 THROUGH JUNE 18, 2014, WHICH MAY EXHIBIT A MALFUNCTION INDICATOR LIGHT (MIL) ON WITH DTC C1212. TO APPLY THE IMPROVED LOGIC, THE ECM SHOULD BE REPROGRAMMED USING THE GDS/KDS DOWNLOAD, AS DESCRIBED IN THIS BULLETIN.

THIS SPECIAL SERVICE TOOL (SST) WAS DEVELOPED TO IMPROVE THE EFFICIENCY AND EFFECTIVENESS OF UPDATING 2010MY, AND LATER, KIA AUDIO HEAD UNITS USING A GDS, AND NOW, THE SAME FUNCTIONALITY IS AVAILABLE ON KDS. SOME TECHNICIANS MAY NOT BE AWARE OF THE BENEFITS THE AUM TOOL HAS TO OFFER. THE AUM ELIMINATES THE NEED FOR MULTIPLE USB FLASH DRIVES FOR SPECIFIC VEHICLE MODELS AND APPLICATIONS WHICH, IF MISAPPLIED, MAY RESULT IN AN IMPROPER AUDIO SYSTEM SOFTWARE UPDATE AND/OR LOCKED UP HEAD UNIT. ADDITIONALLY, FIELD REPORTS HAVE INDICATED THAT USB DRIVES FOR AUDIO UPDATES ARE EASILY LOST OR MISPLACED.

RELATED TO THE ECM SOFTWARE UPGRADE OF SOME 2014~2015MY FORTE (YD), PRODUCED FROM DECEMBER 7, 2013 TO APRIL 16, 2015, AND SOME 2014MY SPORTAGE (SL) VEHICLES, PRODUCED FROM APRIL 4, 2013 THROUGH JUNE 18, 2014, WHICH MAY EXHIBIT A MALFUNCTION INDICATOR LIGHT (MIL) ON WITH DTC C1212. TO APPLY THE IMPROVED LOGIC, THE ECM SHOULD BE REPROGRAMMED USING THE GDS/KDS DOWNLOAD, AS DESCRIBED IN THIS BULLETIN. FOR CONFIRMATION THAT THE LATEST REFLASH HAS BEEN DONE TO A VEHICLE YOU ARE WORKING ON, VERIFY ROM ID USING THE TABLES IN THIS TSB.

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

with the All-Wheel-Drive (AWD) system due to tire sizes of differing circumference. Some customers may complain of a chatter sensation felt in the drivetrain of the vehicle and/or the failure of drivetrain component(s). A difference in tire size (width, aspect ratio, construction, rim diameter etc.) may be the cause.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.

related to the Smart Key Systems on vehicles equipped with A/T (automatic transaxle) and Start/Stop Buttons (SSB).

Damper Clutch (D/C) Solenoid on 6-speed automatic transaxles with DTC P0741 (active or history), instead of replacing the transaxle. To reduce vehicle repair time, this procedure can be performed with the transaxle installed in the vehicle.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

RELEARN THE ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE ECM/PCM.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE PCM/TCM. AFTER THE ADAPTIVE VALUES ARE RESET, THE TRANSMISSION COMPUTER ADAPTIVE VALUES MUST BE RELEARNED BY DRIVING IN A PRECISE MANNER TO TEACH THE COMPUTER THE PROPER SOLENOID DUTY AND LINE PRESSURE FOR THE NEW TRANSMISSION/COMPUTER COMBINATION.

vehicles are registered in one of the S.177 States to show that the recall has been completed on their vehicles. The S.177 States are: Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington

advising of the new Voluntary Emissions Service Campaign.

to the customers whose vehicles are registered in one of the S.177 States ( Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont, and Washington).

provided to the customers whose vehicles are registered in one of the S.177 States ( Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont, and Washington).

Voluntary Emissions Service Campaign to inspect the evaporative canister and, if necessary, install an Auxiliary Canister Kit to improve evaporative system performance.

illuminated with DTC(s) P0442, P0455, P0456, or P0457 (Evaporative Emissions System-Leak detected) and the evaporative (EVAP) leak self-test resulted in NTF, a manual EVAP test is recommended.

FUEL INJECTORS IN SOME SORENTO (XMA) PRODUCED 12/17/2012~12/11/2014, OPTIMA (QF) PRODUCED 07/28/2013~10/02/2015, OPTIMA (TF) PRODUCED 09/09/2013~07/23/2015 2014~2015MY, AND SPORTAGE (SL) PRODUCED 09/01/2013~12/01/2014, WHICH MAY EXHIBIT A MALFUNCTION INDICATOR LAMP (MIL) ON ALONG WITH DTCS P0263, P0266, P0269 AND/OR P0272. FOLLOW THE PROCEDURE OUTLINED IN THIS BULLETIN TO DIAGNOSE AND REPLACE THE AFFECTED INJECTOR TO CORRECT THE CONCERN.

launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.

launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.

states where heavy amounts of road salt are used of a service campaign to add additional anti-corrosion material to underbody components of vehicle.

shape of suction cups to appear on the surface of the windshield, as shown below.

closing effort on some 2011MY to 2014MY Sportage (SL) vehicles, first, verify the customer concern by comparing the closing effort on the affected vehicle to other like vehicles. Make sure all windows are rolled up and use minimal effort to try and close the hatch. If more effort is required to close the hatch than on like vehicles, perform this following procedure.

a new Special Service Tool (SST) (A) developed to prevent the hood release lever pivot point (B) from being damaged when removing the hood release lever. Follow the instructions included in this bulletin to properly remove the hood release lever using the new SST.

regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.

article for detailed information on applicable models, model year and system supplier; along with the applicable Hotline contact information and business hours.

traffic customer complaints, as detailed in this Article.

ACTUATOR OF SOME ALL-WHEEL DRIVE (AWD) EQUIPPED 2011~2016MY SPORTAGE (SL) VEHICLES, PRODUCED FROM MAY 6, 2010 THROUGH FEBRUARY 19, 2013 AND SOME AWD EQUIPPED 2011~2015MY SORENTO (XMA) VEHICLES, PRODUCED FROM OCTOBER 24, 2009 THROUGH DECEMBER 11, 2014, WHICH MAY EXHIBIT AN INOPERATIVE AWD SYSTEM WITH THE MALFUNCTION INDICATOR LAMP (MIL) ON AND DTCS P1820/1821/1822/1823/1824 (ACTIVE OR IN HISTORY). TO CORRECT THIS CONCERN, REPLACE THE AFFECTED HYDRAULIC ACTUATOR BY REFERRING TO THE APPLICABLE SERVICE PROCEDURE ON KGIS.

SPORTAGE VEHICLES, WILL EXHIBIT AN INOPERATIVE AWD SYSTEM WITH MALFUNCTION INDICATOR LAMP. *LJ

diagnosis of the Inhibitor Switch.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

once fully attached, are utilized in various Kia models and are strictly intended for ?one time use.? Some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.? It is critical for technicians to be aware that ALL such locking fasteners, regardless of type, are for ?one time use? only.

strictly intended for ?one time use?. Though not limited to the following, some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.?

now making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.

function using the GDS.

keys that could be programmed to a vehicle was 2. On certain 2014-15MY Kia vehicles, the amount of keys that can be programmed to a vehicle has increased to 3. For information on the current number of keys ?learned? by the system, access SMK > Current Data in GDS, as shown below. To program any additional keys, follow the applicable service procedure on KGIS.

CAMERA OF SOME KIA VEHICLES (SEE TABLE ON PG. 6 FOR SPECIFIC MODELS AND PRODUCTION DATES) WHICH MAY EXHIBIT INADEQUATE IMAGE QUALITY FROM THE REAR VIEW CAMERA. DIAGNOSE THE CONCERNS USING THE INFORMATION IN THIS BULLETIN AND, IF NECESSARY, REPLACE THE REAR VIEW CAMERA WITH AN IMPROVED PART BY FOLLOWING THE APPLICABLE SERVICE PROCEDURE ON KGIS.

SOME 2014~2015MY SPORTAGE (SL), FORTE (YD), OPTIMA (TF/QF), OPTIMA HYBRID (TF HEV) AND SORENTO (XMA) VEHICLES, WHICH MAY EXHIBIT AN INOPERATIVE UVO MEDIA BUTTON.

SOME 2014~2015MY SPORTAGE (SL), FORTE (YD), OPTIMA (TF/QF), OPTIMA HYBRID (TF HEV) AND SORENTO (XMA) VEHICLES, WHICH MAY EXHIBIT AN INOPERATIVE UVO MEDIA BUTTON.

you last August and again last October to provide you with updates regarding news reports about non-collision fires in Kia vehicles and the status of Kia?s cooperative work with NHTSA.

FOR OTHER SPORTAGE MODELS, SEE WTY BULLETIN 2017-09 (SC147).