2020 Kia Soul TSBs

(CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

advising that Kia is conducting Customer Satisfaction Campaign. Kia has developed a new zinc-reinforced ignition cylinder protector hardware upgrade and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Prior notifications stated that this modification had to be performed by July 1, 2025, but the subject vehicles are now eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 19, 2025 through December 31, 2025)

is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)

(CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

tablet on certain Kia engine/model vehicles. The piston oil ring(s) in certain Kia engines may, over time, damage the surface of the engine cylinder wall. This may lead to increased oil consumption which will eventually result in abnormal noise from the engine and/or illumination of the oil pressure warning light. The applicable vehicle may or may not have the Piston Noise Sensing System (PNSS) software installed at the time of an engine vibration inspection. The PNSS software may detect engine noise triggering a DTC P132700.

perform an engine vibration inspection using the Kia Diagnostic System (KDS) tablet on certain 2020 - 2023 MY Kia Soul (SK3) 2021 - 2023 MY Seltos (SP2) Kia vehicles equipped with 2.0L Nu MPI Engines. The piston oil ring(s) in certain Kia engines may, over time, damage the surface of the engine cylinder wall. This may lead to increased oil consumption which will eventually result in abnormal noise from the engine and/or illumination of the oil pressure warning light. The applicable vehicle may or may not have the Piston Noise Sensing System (PNSS) software installed at the time of an engine vibration inspection. The PNSS software may detect engine noise triggering a DTC P132700.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

(SC209Y) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (SC209A) titled ECM Logic Improvement for Piston Ring Noise Sensing System. If DTC P1327 is present after the ECM Logic Improvement is performed per SC209A, follow the instructions in this bulletin to replace the engine long block.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

an additional vehicle modification available for installation to help deter or thwart attempted thefts. This modification consists of a theft deterrent ignition cylinder protector and will be available to you free of charge for eighteen (18) months from the date of this letter.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

(CS2311) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 13, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the brake air bleeding procedure for 2020MY~ Soul (SK3) vehicles equipped with Electronic Stability Control (ESC) module which may exhibit a "honk" noise when using Idle Stop and Go (ISG) and/or Hill Start Assist Control (HAC).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the brake air bleeding procedure for 2020MY~ Soul (SK3) vehicles equipped with Electronic Stability Control (ESC) module which may exhibit a "honk" noise when using Idle Stop and Go (ISG) and/or Hill Start Assist Control (HAC).

has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to improve the logic of the Engine Control Module (ECM) on some 2020-2021MY Soul (SK3) vehicles and 2021MY Seltos (SP2) vehicles produced in the date ranges shown below, equipped with NU 2.0L ATK engines, which may exhibit engine starting related DTC P0605 and/or thermostat related DTC P2181.

information on some 2010-2013MY Soul (AM), 2014-2019MY Soul (PS), and 2020~MY Soul (SK3) vehicles equipped with the engines listed below, which may set DTC P0011, P0014, P0016, or P0017 after an engine replacement. If these DTCs were not present prior to engine replacement, the camshaft reluctor wheel (also called pulse wheel) may not be in the correct position when engine is at Top Dead Center and may be sending an erroneous signal to the PCM, causing the DTC. Follow the procedure outlined in this publication, with engine set to Top Dead Center (TDC), to inspect and identify whether the reluctor wheel is correctly clocked on the camshaft, and if not, how to correctly position it.

been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (SC209A) titled "ECM Logic Improvement for Piston Ring Noise Sensing System". If DTC P1327 is present after the ECM Logic Improvement is performed per SC209A, follow the instructions in this bulletin to replace the engine long block.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

provides information related to the Technical Service Bulletin previously published in (SC209A) titled "ECM Logic Improvement for Piston Ring Noise Sensing System". If DTC P1327 is present after the ECM Logic Improvement is performed per SC209A, follow the instructions in this bulletin to replace the engine long block.

has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to improve the logic of the Engine Control Module (ECM) on some 2020-2021MY Soul (SK3) vehicles produced from November 24, 2018 through January 4, 2021 and 2021MY Seltos (SP2) vehicles produced from November 20, 2019 through January 12, 2021, equipped with NU 2.0L ATK engines, which may exhibit engine poor starting related DTC P0605 and/or thermostat related DTC P2181.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to update the software logic of the Engine Control Module (ECM) system on some 2019MY Stinger (CK) vehicles equipped with the 2.0L T-GDI engine and 8AT transmission, 2020MY Soul (SK3) vehicles with 2.0L MPI engine and 6MT transmission, and 2020MY Sportage (QL) vehicles with 2.4L GDI engine and 6AT transmission, in order to improve OBD authentication code display logic.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

procedure to update the software logic of the Engine Control Module (ECM) system on some 2019MY Stinger (CK) vehicles equipped with the 2.0L T-GDI engine and 8AT transmission, 2020MY Soul (SK3) vehicles with 2.0L MPI engine and 6MT transmission, and 2020MY Sportage (QL) vehicles with 2.4L GDI engine and 6AT transmission, in order to improve OBD authentication code display logic.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

provides the procedure to improve the logic of the Engine Control Module (ECM) on some 2020-2021MY Soul (SK3) vehicles produced from November 24, 2018 through January 4, 2021 and 2021MY Seltos (SP2) vehicles produced from November 20, 2019 through January 12, 2021, equipped with NU 2.0L ATK engines, which may exhibit engine poor starting related DTC P0605 and/or thermostat related DTC P2181.

This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. - This bulletin provides information related to extracting in use performance tracking emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

regarding the brake air bleeding procedure for 2020MY~ Soul (SK3) vehicles equipped with Electronic Stability Control (ESC) module which may exhibit a "honk" noise when using Idle Stop and Go (ISG) and/or Hill Start Assist Control (HAC).

procedure to improve the logic of the Engine Control Unit (ECU) on some 2020MY Soul (SK3) vehicles equipped with 1.6T GDI and 7-Speed Dual Clutch Transmission (DCT), produced from November 15, 2018 through December 26, 2019, which may exhibit check engine lamp with misfire and/or coolant DTCs.

information related to extracting "in use performance tracking" emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting.

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

of the Engine Control Unit (ECU) on some 2020MY Soul (SK3) 1.6T vehicles, produced from November 15, 2018 through February 28, 2019, which may exhibit a malfunction indicator lamp (MIL) illumination with DTC P0606.

of the Engine Control Unit (ECU) on some 2020MY Soul (SK3) 1.6T vehicles, produced from November 15, 2018 through February 28, 2019, which may exhibit a malfunction indicator lamp (MIL) illumination with DTC P0606.

advising that Kia is conducting Voluntary Service Campaign to update the software programming on the Transmission Control Module (TCM) and, if necessary, replace the Intelligent Variable Transmission (IVT) on certain 2020-2021 MY Soul vehicles.

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

Intelligent Variable Transmission (IVT) Oil Pressure Sensor (OPS) on some 2018-2024MY vehicles listed on page 3 equipped with IVT. The affected vehicles may exhibit a malfunction indicator lamp (MIL) illuminated on the instrument cluster with DTCs P084500, P084600, and/or P0867XX present with no drivability concerns due to a failed IVT oil pressure sensor.

A flush is required ONLY when a transmission is replaced.

to update the Transmission Control Module (TCM) software logic and, if necessary, replace the Intelligent Variable Transmission (IVT) assembly on certain 2019-2021MY model vehicles listed in the chart below, which may exhibit an MIL ON with the DTC(s) listed below and a lack/delay in acceleration due to transmission slippage.

been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. (This bulletin was previously referred as SA424 or ELE 200.) This bulletin provides the procedure to update the Transmission Control Module (TCM) software logic and, if necessary, replace the Intelligent Variable Transmission (IVT) on certain 2019-2021MY vehicles listed in the chart below. The affected vehicles may exhibit the illumination of MIL with the DTC(s) listed below in addition to a lack of acceleration or delay in accelerating due to transmission slippage.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. (This bulletin was previously referred as 'SA424' or 'ELE 200'.) This bulletin provides the procedure to update the Transmission Control Module (TCM) software logic and, if necessary, replace the Intelligent Variable Transmission (IVT) on certain 2019-2021MY vehicles listed in the chart below. The affected vehicles may exhibit the illumination of MIL with the DTC(s) listed below in addition to a lack of acceleration or delay in accelerating due to transmission slippage.

been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. (This bulletin was previously referred as 'SA424' or 'ELE 200'.) This bulletin provides the procedure to update the Transmission Control Module (TCM) software logic and, if necessary, replace the Intelligent Variable Transmission (IVT) on certain 2019-2021MY vehicles listed in the chart below. The affected vehicles may exhibit the illumination of MIL with the DTC(s) listed below in addition to a lack of acceleration or delay in accelerating due to transmission slippage.

to update the Transmission Control Module (TCM) software logic and, if necessary, replace the Intelligent Variable Transmission (IVT) assembly on certain 2019-2021MY model vehicles listed in the chart below, which may exhibit an MIL ON with the DTC(s) listed below and a lack/delay in acceleration due to transmission slippage. To correct this concern, if necessary, apply the improved software logic to the CVT system using the KDS ECU Upgrade function as described in this bulletin and replace the IVT assembly.

been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. (This bulletin was previously referred to as SA424 or ELE 200.) This bulletin provides the procedure to update the Transmission Control Module (TCM) software logic and, if necessary, replace the Intelligent Variable Transmission (IVT) on certain 2019-2021MY vehicles listed in the chart below. The affected vehicles may exhibit the illumination of MIL with the DTC(s) listed below in addition to a lack of acceleration or delay in accelerating due to transmission slippage.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace Dual Clutch Assembly and upgrade the TCU on some 2016-2020MY Kia vehicles listed in the table below, equipped with the 7 Speed Dual Clutch Transmission (DCT), which might exhibit clutch judder when accelerating from a stop.

Campaign to improve the Transmission Control Module (TCM) logic and, if necessary, replace the Intelligent Variable Transmission (IVT) on some 2020-2021 Soul vehicles.

the procedure to replace Dual Clutch Assembly and upgrade the TCU on some 2016-2020MY Kia vehicles listed on the table below, equipped with the 7 Speed Dual Clutch Transmission (DCT), which might exhibit clutch judder when accelerating from a stop. If the vehicle body vibrates without the steering wheel shuddering when performing creep driving test (driving the vehicle up to 3mph), the vehicle is exhibiting clutch judder. The creep test can be conducted by driving at a speed slower than 5 mph after releasing the brake.

(This bulletin was previously referred as 'SA424' or 'ELE 200'.) This bulletin provides the procedure to update the Transmission Control Module (TCM) software logic and, if necessary, replace the Intelligent Variable Transmission (IVT) on certain 2019-2021MY vehicles listed in the chart below. The affected vehicles may exhibit the illumination of MIL with the DTC(s) listed below in addition to a lack of acceleration or delay in accelerating due to transmission slippage.

Transmission Control Module (TCM) logic and, if necessary, replace the Intelligent Variable Transmission (IVT) on some 2020-2021 Soul vehicles.

improve the Transmission Control Module (TCM) logic and, if necessary, replace the Intelligent Variable Transmission (IVT) on some 2019-2020 Forte; 2020-2021 Soul, and 2021 Seltos vehicles.

Voluntary Emissions Service Campaign to improve the Transmission Control Module (TCM) logic and, if necessary, replace the Intelligent Variable Transmission (IVT) on some 2019-2020 Forte; 2020-2021 Soul, and 2021 Seltos vehicles.

Campaign to improve the Transmission Control Module (TCM) logic and, if necessary, replace the Intelligent Variable Transmission (IVT) on some 2019-2020 Forte; 2020-2021 Soul, and 2021 Seltos vehicles.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to improve the Transmission Control Module (TCM) logic and if necessary, replace the Intelligent Variable Transmission (IVT) on 2019-2021MY vehicleswhich may exhibit a MIL with certain DTC(s).

bulletin has been revised to include additional information. This bulletin provides the procedure to improve the Transmission Control Module (TCM) logic and if necessary, replace the Intelligent Variable Transmission (IVT) on 2019-2021MY vehicles which may exhibit a MIL with the DTC(s) listed below.

bulletin has been revised to include additional information. This bulletin provides the procedure to improve the Transmission Control Module (TCM) logic and if necessary, replace the Intelligent Variable Transmission (IVT) on 2019-2021MY vehicles which may exhibit a MIL with the DTC(s) listed below. To correct this concern, apply the improved logic to the CVT system using the KDS ECU Upgrade function as described in this bulletin and/or replace the IVT assembly.

bulletin provides the procedure to improve the Transmission Control Module (TCM) logic and if necessary, replace the Intelligent Variable Transmission (IVT) on 2019-2021MY vehicles which may exhibit a MIL with the DTC(s) listed below. To correct this concern, apply the improved logic to the CVT system using the KDS ECU Upgrade function as described in this bulletin and/or replace the IVT assembly.

This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.

bulletin provides the procedure to replace the 7-Speed Dual Clutch Transmission (DCT) assembly on some 2019-2020MY Soul (PS, SK3) vehicles, which may exhibit harsh shifting and/or Malfunction Indicator Lamp (MIL) with transmission related DTCs due to crack(s) on the 3rd and 7th gear synchronizer hub.

when inspecting the oil level on a Dual Clutch Transmission (DCT) for 2020MY~ Soul (SK3) vehicles. The DCT assembly now sits at a 5 degree difference from the previous Soul (PS). This change requires an updated oil level inspection procedure.

into 1st gear concern on 2020MY Soul (SK3) vehicles equipped with manual transmissions. The possible root cause could be that the shift/control cable is out of adjustment.

feature available on the AVN 5.0 Wide and Display Audio head units. The Extend Rear Camera Use feature on the head unit activates the rear view camera regardless of the gear position, Drive or Reverse. If the gear is shifted from Reverse to Drive or Reverse to Neutral the Extend Rear Camera Use feature will keep the rear view camera activated until the vehicle exceeds a predetermined factory-set speed. Note: the parking guide lines will not appear on the screen when in Drive or Neutral..

Dealer Mode Factory Reset on multiple 2020-2021MY vehicles (listed on page 5) equipped with AVN 5.0 Wide head units. The affected vehicles may exhibit inoperable and/or interrupted Kia Connect services due to a logic error with the current software version. This logic error may affect the Kia Connect services: calendar, weather, sports, vehicle diagnostics, maintenance and/or Kia Connect services rendering these features inoperable.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software on 5th Generation AVN wide on certain 2020-2024MY Kia vehicles (refer to model list on page 8) to remedy a non-responsive or inoperative radio (FM, AM, SXM, etc.) concern. The affected AVN unit on the vehicles may not respond when pressing the RADIO hard key/button on the AVN unit or when selecting the RADIO icon on the AVN menu screen.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software on 5th Generation AVN wide on certain 2020-2024MY Kia vehicles (refer to model list on page 3) to remedy a 'non-responsive' or 'inoperative' radio (FM, AM, SXM, etc. ) concern. The affected AVN unit on the vehicles may not respond when pressing the 'RADIO' hard key/button on the AVN unit or when selecting the 'RADIO' icon on the AVN menu screen.

information to update the software on 5th Generation AVN wide on certain 2020-2023MY Kia vehicles to remedy an inaccurate map location, freezing AVN screen, or experiencing a delay when using Google Maps or Waze through wired Apple CarPlay.

information to update the software on 5th Generation AVN wide on certain 2020-2023MY Kia vehicles (refer to model list on page 3) to remedy a warning sound accompanied by a 'Slippery road ahead. Drive carefully' or 'Uneven road ahead. Drive carefully' warning which is displayed on the instrument cluster. The current AVN software causes the warning sound and message to repeat approximately every ten (10) seconds, if the vehicle is not in motion, in 'PARK' or driving on even surfaces.

(refer to model list on page 3) to remedy a 'non-responsive' or 'inoperative' radio (FM, AM, SXM, etc. ) concern. The affected AVN unit on the vehicles may not respond when pressing the 'RADIO' hard key/button on the AVN unit or when selecting the 'RADIO' icon on the AVN menu screen.

update the software on 5th Generation AVN wide on certain 2020-2023MY Kia vehicles to remedy a 'non-responsive' or 'inoperative' radio (FM, AM, SXM, etc.) concern. The affected AVN unit on the vehicles may not respond when pressing the 'RADIO' hard key/button on the AVN unit or when selecting the 'RADIO' icon on the AVN menu screen. Follow the procedure outlined in this publication to update the software on 5th Generation AVN wide units using the applicable USB Flash Drive A or B for the applicable vehicle.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop contains information regarding the log file collection procedure for 2020MY~ models equipped with AVN 5.0/W or Display Audio 2.0 head units.

the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster. The KDS is required to change the setting from "Workshop" to "Customer Mode."

a memory concern with the AVN 5.0 Wide head unit while downloading the contact list from a paired phone. The concern also affects Voice Recognition (VR) functionality.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop contains information regarding the log file collection procedure for 2020MY~ models equipped with AVN 5.0/W or Display Audio 2.0 head units.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to turn OFF the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to turn OFF the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster.

file collection procedure for 2020MY~ models equipped with AVN 5.0/W or Display Audio 2.0 head units.

operation of Multi-Function Camera (MFC) on some Kia vehicles. When normal operation is not possible due to certain outside environment conditions (such as sunlight glare, heavy rain, sunlight, snow, fog and/or substance/debris) causing a temporary concern. This stops operation causing Warning Lamp ON and/or Pop-up Message displayed on the cluster. This is a normal operation of the ADAS and once environment conditions improve and/or substance/debris are removed, the system will clear itself and operate normally.

the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster.

updating the AVN 5 WIDE software on some 2020MY Telluride (ON) produced from March 23, 2019 through April 30, 2019 and Soul (SK3) vehicles produced from February 18, 2019 to May 2, 2019, which may experience Bluetooth and navigation connection and/or memory issues.

WIDE software on some 2020MY Telluride (ON) produced from March 23, 2019 through April 30, 2019 and Soul (SK3) vehicles produced from February 18, 2019 to May 2, 2019, which may experience Bluetooth and navigation connection and/or memory issues.

feature available on the AVN 5.0 Wide and Display Audio head units.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2020-2022MY Soul (SK3) vehicles produced from November 24, 2018 through December 11, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.

COMPATIBILITY (CS2310) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 7. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2020-2022MY Soul (SK3) vehicles produced from November 24, 2018 through December 11, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

COMPATIBILITY (CS2310) - This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 6. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2020-2022MY Soul (SK3) vehicles produced from November 24, 2018 through December 11, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2020-2022MY Soul (SK3) vehicles produced from November 24, 2018 through December 11, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop provides information regarding a new interface related to the electronic Dealer (Shipping) / Customer Mode Switch setting on all applicable models.

alignment on 2014MY and later vehicles that may exhibit a warning light ON related to radar sensor alignment errors in the Forward Collision-Avoidance Assist (FCA)/Smart Cruise Control (SCC) system.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop provides information regarding a new interface related to the electronic Dealer / Customer Mode Switch setting on multiple models.

regarding the Blind-Spot Collision Warning (BCW) system setting a DTC C166A87 after replacing a BCW module on 2020-2021 Soul (SK3) vehicles. After replacement, the BCW (BSD) variant coding needs to be performed using the KDS under S/W Management for the options equipped for that vehicle.

provides the procedure to apply improved Diagnostic Trouble Code (DTC) judgement logic for the Electronic Power Steering (EPS) on some 2020MY Soul (SK3) vehicles, produced from November 15, 2018 through October 8, 2019, which requires a software upgrade. Install the improved logic of the EPS using the KDS ECU Upgrade function as described in this bulletin.

extending the New Vehicle Limited Warranty coverage, to all owners, for repairs related to the horn assembly in certain 2020-2025 MY Soul vehicles from 5 years / 60,000 miles to 10 years / 120,000 miles, whichever comes first, starting from the date the vehicle was first put into service. This warranty extension is to address a horn sound malfunction condition.

the most frequently asked questions regarding the Warranty Extension Campaign WTY041.

dealer principals advising that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for repairs related to the horn assembly in certain 2020-2025 MY Soul vehicles, manufactured from November 15, 2018 through August 13, 2024, from 5 years / 60,000 miles to 10 years / 120,000 miles, whichever comes first, starting from the date the vehicle was first put into service. This warranty extension is to address a horn sound malfunction condition.

advising that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for repairs related to the horn assembly in certain 2020-2025 MY Soul vehicles, manufactured from November 15, 2018 through August 13, 2024, from 5 years / 60,000 miles to 10 years / 120,000 miles, whichever comes first, starting from the date the vehicle was first put into service. This warranty extension is to address a horn sound malfunction condition.

New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides information on setting the "Service Interval Reminder" feature available on most 2014-2023MY Kia vehicles (refer to model list on page 2). If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance. Refer to TSB ENG241 for 2023MY~ vehicles equipped with the Oil Life Management System (OLMS) feature not included in table on page 2.

Interval Reminder" feature available on most Kia vehicles. If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance.

to re-tighten the wiper arm nuts to the torque specification on some 2020MY Soul (SK3) vehicles produced from November 4, 2019 through December 12, 2019, which may not have been properly torqued during assembly.

for mileage setting on the listed vehicles with newly replaced instrument clusters.

on some 2020MY Soul (SK3) vehicles produced from December 10, 2018 through January 11, 2019 which may exhibit a weak intermittent or non-operational "sound" due to moisture inflow into the horn.

with the customer letter advising them to submit the form if they had paid for repairs for this same matter prior to the warranty extension campaign program launch.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the service reminder setting, which may have been auto-set by the Kia Vehicle Inspection and Delivery application (KVID) at time of Pre-Delivery Inspection (PDI). Beginning with the 2023MY, Oil Life Monitoring (OLM) has been applied to all models, except Forte (BDm), Stinger (CK), Telluride (ON) and Soul (SK3). Refer to TSB ENG241 for additional information. As of 08/11/2023, the service reminder auto-set feature by KVID has been disabled for ALL models NOT equipped with OLM.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This pitstop provides the KDS service procedure for mileage setting on the models listed below with newly replaced instrument clusters. Certain models allow for mileage setting with the KDS, which prevents the need to send out the instrument cluster to a 3rd party for mileage adjustment (refer to PS264). After a new cluster is installed, cluster (variant) coding may also need to be conducted using the KDS. Make sure the KDS software is also updated to the latest version. Mileage setting should be performed by using the KDS only, as described in this bulletin.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on the inspection and replacement of the front camera on some vehicles. Due to an internal control chip concern inside the camera, the vehicle may exhibit a Forward Collision Avoidance Assist Warning Lamp (A) and/or Master Warning Lamp (B) with C160449 and/or C160649 codes. Certain systems may become temporarily disabled during occurrences: Smart Cruise Control (SCC), Lane Keep Assistance (LKA), Lane Departure Warning (LDW), Forward Collision-Avoidance Assist (FCA), Forward Collision Warning (FCW) and/or Driver Attention Warning (DAW).

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to update the software logic of the front view camera system (FR_CMR) on the vehicles listed below, when a new replacement Front View Camera installed with a part number ending in "SW0". NEW parts with a part number ending in "SW0" do not have the operating software upgrade installed. If the software upgrade is not installed, units will exhibit a warning light ON with Diagnostic Trouble Codes (DTCs) related to the front view camera. Some vehicles require recovery and recording the prior variant coding value before replacement.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on the inspection and replacement of the front camera on some vehicles. Due to an internal control chip concern inside the camera, the vehicle may exhibit a Forward Collision Avoidance Assist Warning Lamp (A) and/or Master Warning Lamp (B) with C160449 and/or C160649 codes. Certain systems may become temporarily disabled during occurrences: Smart Cruise Control (SCC), Lane Keep Assistance (LKA), Lane Departure Warning (LDW), Forward Collision-Avoidance Assist (FCA), Forward Collision Warning (FCW) and/or Driver Attention Warning (DAW).

procedure to update the software logic of the Front Camera (FR_CMR) system on the vehicles listed below, which have had a new replacement Front View Camera installed without software upgrade. If the S/W is not upgraded, units will exhibit a warning light ON with Diagnostic Trouble Codes (DTCs) related to the Front Camera (FR_CMR).

only on the 2020MY Soul GT-Line 1.6T (SK3) with the Comfort and Convenience Package.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to replace the front strut bearing and upper spring pad on both front (LH and RH) strut assemblies on certain 2019-2024MY Forte (BDm) vehicles produced from July 09, 2018 through present, 2020-2024MY Soul (SK3) vehicles produced from November 15, 2018 through present, and 2021-2024 Seltos (SP2) vehicles produced from November 20, 2019 through present. The affected vehicles may exhibit an intermittent noise when turning the steering wheel both when driving and when the vehicle is not in motion.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to replace the front strut bearing and upper spring pad on both front (LH and RH) strut assemblies on certain 2019-2024MY Forte (BDm) vehicles produced from July 09, 2018 through present, 2020-2024MY Soul (SK3) vehicles produced from November 15, 2018 through present, and 2021-2024 Seltos (SP2) vehicles produced from November 20, 2019 through present. The affected vehicles may exhibit an intermittent noise when turning the steering wheel both when driving and when the vehicle is not in motion.

the front strut bearing and upper spring pad on both front (LH and RH) strut assemblies on certain 2019-2024MY Forte (BDm) vehicles produced from July 09, 2018 through present, 2020-2024MY Soul (SK3) vehicles produced from November 15, 2018 through present, and 2021-2024 Seltos (SP2) vehicles produced from November 20, 2019 through present. The affected vehicles may exhibit an intermittent noise when turning the steering wheel both when driving and when the vehicle is not in motion.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the repair procedure for the Integrated Brake Actuation Unit (iBAU) system on some 2014-2019MY EV/Hybrid/Plug-In Hybrid vehicles listed (see table), which may exhibit a "honking" (Hissing) noise due to air remaining in the brake fluid system.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information associated with the Warranty Extension Program (WTY041) to inspect and, if necessary, replace the horn assembly on certain 2020-2025MY Soul (SK3) vehicles produced from November 15, 2018 through August 13, 2024, The affected vehicles may experience a distorted or an inoperative horn sound caused by to corrosion and dust inside the horn assembly. The warranty coverage for repairs related to the horn assembly have been extended from 5 years / 60,000 miles to 10 years / 120,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

provides information associated with the Warranty Extension Program (WTY041) to inspect and, if necessary, replace the horn assembly on certain 2020-2025MY Soul (SK3) vehicles produced from November 15, 2018 through August 13, 2024, The affected vehicles may experience a distorted or an inoperative horn sound caused by to corrosion and dust inside the horn assembly. The warranty coverage for repairs related to the horn assembly have been extended from 5 years / 60,000 miles to 10 years / 120,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

the overhead console lamp assembly and sunglass door latch on some 2012-2023MY model vehicles listed in the table below, which may encounter the sunglass case of the overhead console lamp not closing properly.

now making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

procedure to repair a creaking/popping noise from the steering column area on some 2020MY Soul (SK3) vehicles, which may be heard when turning the steering wheel at low speeds or while stopped. To repair this concern, follow the procedure outlined in this bulletin to replace and install the improved fixed cam kit to the steering column.

resetting the modem in certain 2016-2025MY Kia vehicles listed on page 3 that are equipped with Kia Connect Services. The affected vehicles may encounter the following issues: remote Start/Climate Control function not working, vehicle Status on the Kia Access App not updating, connected routing not functioning properly.

bulletin provides the procedure for updating the AVN 5 WIDE software on some 2020MY Telluride (ON) produced from January 9, 2019 through September 16, 2019 and Soul (SK3) vehicles produced from November 22, 2018 through September 19, 2019, which may experience inoperative voice recognition when setting a destination

In the event a wheel alignment is needed, ensure your alignment equipment has the correct specifications programmed into the PC database.