2017 Kia Soul TSBs

advising that Kia is conducting Customer Satisfaction Campaign. Kia has developed a new zinc-reinforced ignition cylinder protector hardware upgrade and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Prior notifications stated that this modification had to be performed by July 1, 2025, but the subject vehicles are now eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 19, 2025 through December 31, 2025)

Kia is conducting a important Product Improvement Campaign to perform a software update on 2017-2019 MY Kia Soul vehicles equipped with 2.0-liter Nu GDI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (ECU)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

Kia conducting Product Improvement Campaign to perform a software update on 2017-2019 MY Kia Soul vehicles equipped with 2.0-liter Nu GDI engines to protect the engine from excessive connecting rod bearing damage.

DTC P1326 (PI2107Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published (PI2107) titled Nu 2.0L GDI - Knock Sensor Detection System ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

Kia is conducting a Product Improvement Campaign to perform a software update on 2017-2019 MY Kia Soul vehicles equipped with 2.0-liter engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

an additional vehicle modification available for installation to help deter or thwart attempted thefts. This modification consists of a theft deterrent ignition cylinder protector and will be available to you free of charge for eighteen (18) months from the date of this letter.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

(CS2311) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 13, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to update the emissions-related logic of the Electronic Control Module (ECM) with an improved version on certain 2017-2019MY Soul (PS) vehicles equipped with the Nu 2.0L GDI SULEV engine, produced from July 29, 2016 through December 19, 2018. To ensure compliance with emissions regulations, apply the improved software update to the Engine system using the KDS ECU upgrade function as described in this bulletin.

information equipped with a Gamma 1.6L GDI regarding a 'low oil pressure' concern during engine idle on vehicles engine due to a missing dowel pin, after a short block engine replacement. An internal oil leakage will cause a decrease in oil pressure without the instal lation of the dowel pin location described in this bulletin. Confirm that the dowel pin was installed for an engine exhibiting a low oil pressure concern after a short block replacement.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. Do NOT install PI2107 KSDS ECU Logic Improvement on 20 17 20 19MY Soul (PS) w/Nu 2.0L GDI SULEV models. The KSDS will automatically be installed under SC251. Utilize Op Code 210149R1 for all SULEV models and proceed to SC251. All claims are subject to Warranty review and chargeback.This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS), in order to protect the engine from excessive connecting rod bearing damage. This update is for certain 2017-2019MY Soul (PS) vehicles equipped with Nu 2.0L GDI engines, produced from July 29, 2016 through December 21, 2018.

the procedure to update the emissions-related logic of the Electronic Control Module (ECM) with an improved version on certain 2017-2019MY Soul (PS) vehicles equipped with the Nu 2.0L GDI SULEV engine, produced from July 29, 2016 through December 19, 2018. To ensure compliance with emissions regulations, apply the improved software update to the Engine system using the KDS ECU Upgrade function as described in this bulletin.

conducting a Voluntary Emissions Service Campaign on certain 2017-2019 MY Kia Soul vehicles equipped with Nu 2.0L GDI SULEV engines manufactured from July 29, 2016 through December 19, 2018 to improve the emission logic in the Electronic Control Module ('ECM') to ensure compliance with emissions regulations.

dealer Parts and Service Managers that Kia is conducting a Voluntary Emissions Service Campaign on certain 2017-2019 MY Kia Soul vehicles equipped with Nu 2.0L GDI SULEV engines manufactured from July 29, 2016 through December 19, 2018 to improve the emission logic in the Electronic Control Module ('ECM') to ensure compliance with emissions regulations.

that Kia is conducting a Voluntary Emissions Service Campaign on certain 2017-2019 MY Kia Soul vehicles equipped with Nu 2.0L GDI SULEV engines manufactured from July 29, 2016 through December 19, 2018 to improve the emission logic in the Electronic Control Module ('ECM') to ensure compliance with emissions regulations.

information on some 2010-2013MY Soul (AM), 2014-2019MY Soul (PS), and 2020~MY Soul (SK3) vehicles equipped with the engines listed below, which may set DTC P0011, P0014, P0016, or P0017 after an engine replacement. If these DTCs were not present prior to engine replacement, the camshaft reluctor wheel (also called pulse wheel) may not be in the correct position when engine is at Top Dead Center and may be sending an erroneous signal to the PCM, causing the DTC. Follow the procedure outlined in this publication, with engine set to Top Dead Center (TDC), to inspect and identify whether the reluctor wheel is correctly clocked on the camshaft, and if not, how to correctly position it.

related to the Technical Service Bulletin previously published (PI2107) titled "Nu 2.0L GDI - Knock Sensor Detection System ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS), in order to protect the engine from excessive connecting rod bearing damage. This update is for certain 2017-2019MY Soul (PS) vehicles equipped with Nu 2.0L GDI engines, produced from July 29, 2016 through December 21, 2018.

bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS), in order to protect the engine from excessive connecting rod bearing damage. This update is for certain 2017-2019MY Soul (PS) vehicles equipped with Nu 2.0L GDI engines, produced from July 29, 2016 through December 21, 2018.

conducting a Product Improvement Campaign to perform a software update on 2017-2019 MY Kia Soul vehicles equipped with 2.0-liter Nu GDI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU") (PI2107).

Parts and Service Managers that Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2017-2019 MY Kia Soul vehicles equipped with 2.0-liter Nu GDI engines, manufactured from July 29, 2016 through December 21, 2018 (PI2107).

Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2017-2019 MY Kia Soul vehicles equipped with 2.0-liter Nu GDI engines, manufactured from July 29, 2016 through December 21, 2018.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

diagnosing and/or repairing some 2012-2019MY Soul (AM/PS) vehicles (refer to table below for applicable engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

on the installation of an add-on auxiliary canister on some 2017-2019MY Soul (PS) vehicles equipped with the 1.6L T-GDI engine, produced from July 25, 2016 through December 12, 2018.

Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2017-2019 MY Kia Soul vehicles equipped with the 1.6-liter Turbo-GDI engine manufactured from July 25, 2016 through December 12, 2018.

is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2017-2019 MY Kia Soul vehicles equipped with the 1.6-liter Turbo-GDI engine manufactured from July 25, 2016 through December 12, 2018.

and service managers advising that Kia Motors America, Inc. is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2017-2019 MY Kia Soul vehicles equipped with the 1.6-liter Turbo-GDI engine manufactured from July 25, 2016 through December 12, 2018.

is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2017-2019 MY Kia Soul vehicles equipped with the 1.6-liter Turbo-GDI engine manufactured from July 25, 2016 through December 12, 2018.

is sending this notice to remind you in detail of the oil and oil filter maintenance requirements provided in your Owner's Manual which are critical to your engine's health. The purpose of sharing this information is to help you protect the investment you have in your vehicle's engine, to maximize its durability, and to avoid issues associated with insufficient or improper vehicle maintenance.

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

This bulletin provides information relating to all Kia vehicles equipped with Gasoline Direct Injection (GDI) engines. In these engines highly pressurized gasoline is injected via a common fuel rail and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional Multi-Point Fuel Injection (MPI) engine, the gasoline is injected into the intake port of each cylinder at a relatively low pressure. Due to high fuel pressure in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specifications for the GDI fuel system components.

inspection and installation of the steel sealing ball on: * 3.3L & 3.8L Lambda engines for 2007-2008MY Sorento (BL), * 2.0L Nu engines for 2010-2019MY Soul (AM, PS), and * 1.8L & 2.0L Nu engines for 2010-2018MY Forte (TD, YD/YDm), 2019MY~ Forte (BDm). When replacing the cylinder heads on these engines, inspect the lubrication ports for installation of the steel sealing balls. Current replacement cylinder heads may not be equipped with the required steel balls. Identify and locate the nine (9) lubricant passages on 3.3L and 3.8L engines and three (3) on 1.8L and 2.0L engines and verify a steel ball is installed in each.

and if necessary, replace the Air Drain Case on some 2014-18MY Soul (PS), produced from July 21, 2013 through June 1, 2017, some 2012-2017MY Rio (UB), produced from June 21, 2011 through March 31, 2017, some 2014-2017MY Forte (YD) vehicles, produced from February 18, 2013 through March 2, 2017, and some 2017MY Forte (YDm) vehicles, produced from May 16, 2016 through March 6, 2017, which may experience an early shut-off during fuel refill and/or a malfunction indicator lamp (MIL) illumination with DTC(s) P0449 or P0451.

considered serviceable, and should be thoroughly cleaned and transferred to the new engine.

related to extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.

extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting. To facilitate collection of this data at the dealer level, KDS screenshots will allow the capture of relevant parameters.

7-speed Dual Clutch Transmission (DCT), except the 2017MY~ Niro (DE) with a 1.6L Atkinson engine comes equipped with a 6-speed Dual Clutch Transmission (DCT). This automatic transmission is unlike the conventional automatic transmission found in the complete line up of Kia vehicles. The new DCT improves fuel efficiency and can also provide a sportier feel. Certain aspects of this technology may lead to customer concerns if they are unfamiliar with it. To help maximize owner satisfaction on this new technology, Kia would like all dealership sales and service personnel to be familiar with the characteristics of this new transmission.

SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace Dual Clutch Assembly and upgrade the TCU on some 2016-2020MY Kia vehicles listed in the table below, equipped with the 7 Speed Dual Clutch Transmission (DCT), which might exhibit clutch judder when accelerating from a stop.

the procedure to replace Dual Clutch Assembly and upgrade the TCU on some 2016-2020MY Kia vehicles listed on the table below, equipped with the 7 Speed Dual Clutch Transmission (DCT), which might exhibit clutch judder when accelerating from a stop. If the vehicle body vibrates without the steering wheel shuddering when performing creep driving test (driving the vehicle up to 3mph), the vehicle is exhibiting clutch judder. The creep test can be conducted by driving at a speed slower than 5 mph after releasing the brake.

This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.

Unit (TCU) on 2017-2018MY Soul (PS) and Forte (YDm) and 2016-2018MY Optima (JFa) vehicles equipped with 1.6T GDI that have one of the following three components replaced: Dual Clutch Transmission (DCT) assembly; Transmission Control Unit (TCU), and Double Clutch Set.The friction material of the double clutch set has been changed and a TCU logic optimization must be performed in order to prevent initial shift shock.

This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.

(SC334) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to apply additional anti-corrosion material to underbody components, including inspection/replacement of the brake line(s), on certain 2014-2019MY Soul (PS) vehicles produced from July 21, 2013 through December 24, 2018, and were originally sold or are currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.

information to apply additional anti-corrosion material to underbody components, including inspection/replacement of the brake line(s), on certain 2014-2019MY Soul (PS) vehicles produced from July 21, 2013 through December 24, 2018, and were originally sold or are currently registered in one of the 28 states where heavy amounts of road salt are used: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.

conducting a Voluntary Service Campaign to inspect and, if necessary, replace the brake line(s) in certain 2014-2019 MY Soul vehicles that were originally sold in or are currently registered in states where heavy amounts of road salt are used. In addition, an anti-corrosion material will be applied to the underbody components for added protection.

dealer Parts and Service managers advising that Kia is conducting a Voluntary Service Campaign to inspect and, if necessary, replace the brake line(s) in certain 2014-2019 MY Soul vehicles, manufactured from July 21, 2013 through December 24, 2018, that were originally sold in or are currently registered in states where heavy amounts of road salt are used. In addition, an anti-corrosion material will be applied to the underbody components for added protection.

advising that Kia is conducting a Voluntary Service Campaign to inspect and, if necessary, replace the brake line(s) in certain 2014-2019 MY Soul vehicles, manufactured from July 21, 2013 through December 24, 2018, that were originally sold in or are currently registered in states where heavy amounts of road salt are used. In addition, an anti-corrosion material will be applied to the underbody components for added protection.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the repair procedure for the Integrated Brake Actuation Unit (iBAU) system on some 2014-2019MY EV/Hybrid/Plug-In Hybrid vehicles listed (see table), which may exhibit a "honking" (Hissing) noise due to air remaining in the brake fluid system.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

the clock on UVO eServices (UVO 3.0) head units installed on 2017-2018MY vehicles.

This Pitstop provides information regarding the functionality on the latest generation Base Audio System (designated Audio 4.0) that has been applied on some 2017-2018MY Soul (PS) and Sedona (YP) vehicles.

on 2015 - 2017MY Soul EV (PS EV), 2016 - 2017MY K900 (KH), and 2017MY Optima Plug-in Hybrid (PHEV). It is important to note that the head units in these vehicles contain a modem and should NOT be swapped between vehicles under any circumstances. Swapping a head unit from one vehicle to another may result in a non-operational UVO eServices on one of the vehicles. If a head unit needs to be replaced, the factory recommendation is to always order a replacement head unit to ensure proper eServices operations using the new installed/replaced head unit.

on the latest generation Base Audio system (designated Audio 4.0 Type B) that has been applied on 2017MY Soul (PS) and Sedona (YP).

Audio Gen 4.0 Type B software on some 2017MY Soul (PS), produced from July 12, 2016 to August 26, 2016, which may experience a screen freezing, black screen, or other display concerns during initial system startup. These concerns may occur during initial booting. Follow the procedure outlined in this bulletin to correct the concern.

FUNCTIONALITY ON THE LATEST GENERATION BASE AUDIO SYSTEM (DESIGNATED AUDIO 4.0 B) THAT HAS BEEN APPLIED ON 17 MY SOUL AND SEDONA.

dealer Parts and Service Managers that Kia is conducting a Voluntary Service Campaign to update the battery management system (BMS) software on certain 2015-2017 MY Soul EV vehicles manufactured from July 15, 2014 through July 4, 2017 that had their BMS previously replaced and updated under warranty.

New/revised sections of this pitstop are indicated by a black bar in the margin area. This Pitstop provides information regarding a possible mismatch of a SRSCM (Supplemental Restraint System Control Module) and driver seat belt buckle that may set the SRS DTC(s) B168400 and/or B176200 on the models listed below. When diagnosing a vehicle that has been in an accident and/or has recently had a superseded SRSCM replaced, it may be necessary to inspect and replace the driver seat belt buckle with the latest production P/N listed in EPC. Older production driver seat belt buckles have a 4 pin connector and may no longer be compatible with the superseded SRSCM. Only the SRSCM is superseded; the driver seat belt buckle is not superseded.

(Supplemental Restraint System Control Module) and driver seat belt buckle that may set the SRS DTC(s) B168400 and/or B176200 on the models listed below. When diagnosing a vehicle that has been in an accident and/or has recently had a superseded SRSCM replaced, it may be necessary to inspect and replace the driver seat belt buckle with the latest production P/N listed in EPC. Older production driver seat belt buckles have a 4 pin connector and may no longer be compatible with the superseded SRSCM. Only the SRSCM is superseded; the driver seat belt buckle is not superseded. DTC B176200:

The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.

(AUM) firmware update to ensure compatibility with the new Audio 4.0 head units (standard on 17MY Soul (PS) and Sedona (YP)).

the most frequently asked questions regarding the Voluntary Emissions Service Campaign (SC251).

This bulletin provides the procedure to replace the Air Drain Case on some 2014-2018MY Soul (PS), produced from July 21, 2013 through June 1, 2017, some 2012-2017MY Rio (UB), produced from June 21, 2011 through March 31, 2017, some 2014-2017MY Forte (YD), produced from February 18, 2013 through March 2, 2017, and some 2017MY Forte (YDm) vehicles, produced from May 16, 2016 through March 6, 2017, which may experience an early shut-off during fuel refill and/or a Malfunction Indicator Lamp (MIL) illumination with DTCs P0449 or P0451.

models such as K900 (KH), Sedona (YP), Sorento (UMa), Optima (JFa), Sportage (QL), and 17MY Forte (YD, YDm), etc., equipped with a sunroof, a ventilation logic has been applied in order to prevent exhaust gases flowing into the vehicle due to the pressure difference (inside vs outside) that is generated when driving with the sunroof open. This logic allows the system to automatically switch from RECIRCULATION to FRESH mode when the sunroof is open.

most frequently asked questions regarding the Voluntary Service Campaign SC334.

New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides information on setting the "Service Interval Reminder" feature available on most 2014-2023MY Kia vehicles (refer to model list on page 2). If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance. Refer to TSB ENG241 for 2023MY~ vehicles equipped with the Oil Life Management System (OLMS) feature not included in table on page 2.

frequently asked questions regarding the Product Improvement Campaign (PI2107).

Interval Reminder" feature available on most Kia vehicles. If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance.

and all Kia vehicles, after and including 2017MY, incorporate an anti-condensation logic to prevent the interior windows from becoming excessively fogged. The HVAC control head in these vehicles monitors ambient temperature to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature (about 60F or below), the anti-condensation logic may automatically set the air intake mode to FRESH, depending on the other HVAC settings. The anti-condensation logic is also designed to ensure that air intake mode is set to FRESH, as long as all conditions are met. If the user changes the air intake to RECIRCULATION, the anti-condensation logic will take control again after 5 minutes, and change the air intake mode back to FRESH. If this results in an undesired operation, the logic may be enabled or disabled by following the procedure below.

incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.

recycling, and recharging equipment. This equipment is designed to meet SAE J2843 requirements for servicing vehicles containing R1234yf refrigerant.

now making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

certification that the campaign has been completed.

regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.

intermittent flickering, inoperative headlights, or that the headlights stay on indefinitely after the vehicle is turned off, confirm the following actions in this publication have been performed, when applicable.