2013 Kia Soul TSBs

advising that Kia is conducting Customer Satisfaction Campaign. Kia has developed a new zinc-reinforced ignition cylinder protector hardware upgrade and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Prior notifications stated that this modification had to be performed by July 1, 2025, but the subject vehicles are now eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 19, 2025 through December 31, 2025)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2002A, PI2002B and SC200**1) titled Knock Sensor Detection System - ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

provides catalytic converter and engine sub-assembly diagnosis and repair information on certain 2012-2016MY Soul (AM, PS) vehicles produced from July 8, 2011 through August 11, 2016, that previously had the recall campaign SC176 completed. The affected vehicles may exhibit catalyst system efficiency deterioration or a malfunction indicator lamp illumination with an active, history or pending P0420 with or without a P030X misfire DTC.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

an additional vehicle modification available for installation to help deter or thwart attempted thefts. This modification consists of a theft deterrent ignition cylinder protector and will be available to you free of charge for eighteen (18) months from the date of this letter.

an additional vehicle modification available for installation to help deter or thwart attempted thefts. This modification consists of a theft deterrent ignition cylinder protector and will be available to you free of charge for eighteen (18) months from the date of this letter.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

(CS2311) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 13, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

information equipped with a Gamma 1.6L GDI regarding a 'low oil pressure' concern during engine idle on vehicles engine due to a missing dowel pin, after a short block engine replacement. An internal oil leakage will cause a decrease in oil pressure without the instal lation of the dowel pin location described in this bulletin. Confirm that the dowel pin was installed for an engine exhibiting a low oil pressure concern after a short block replacement.

information on some 2010-2013MY Soul (AM), 2014-2019MY Soul (PS), and 2020~MY Soul (SK3) vehicles equipped with the engines listed below, which may set DTC P0011, P0014, P0016, or P0017 after an engine replacement. If these DTCs were not present prior to engine replacement, the camshaft reluctor wheel (also called pulse wheel) may not be in the correct position when engine is at Top Dead Center and may be sending an erroneous signal to the PCM, causing the DTC. Follow the procedure outlined in this publication, with engine set to Top Dead Center (TDC), to inspect and identify whether the reluctor wheel is correctly clocked on the camshaft, and if not, how to correctly position it.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2002A, PI2002B and SC200**1) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

provides the procedure to update the software logic of the Engine Control Module (ECM) system on some 2014-2016MY Soul (PS) vehicles with Gamma 1.6L GDI engines, produced from August 29, 2013 through July 26, 2016, which may exhibit an MIL ON with DTC P050A (Cold Start Idle Air Control System Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in January 2021 (PI2002A and PI2002B, August 2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

IMPROVEMENT (PI2002A) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

information related to the Technical Service Bulletin previously published in January 2021 (PI2002A and PI2002B, August 2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

Soul vehicles equipped with 1.6L Gasoline Direct Injection ("GDI") engines to protect the engine from excessive connecting rod bearing damage (PI2002A).

owners advising them of the updated warranty coverage for the Product Improvement campaign PI2002A. The coverage has been expanded to cover the engine long block assembly for 15 years from the date the vehicle was first put into service or 150,000 miles, whichever occurs first, for both new and used vehicle owners upon completion of this Product Improvement Campaign.

frequently asked questions regarding the product improvement (PI2002A). The warranty coverage information has been updated: "Upon completion of this Product Improvement Campaign, Kia will extend the warranty coverage for the engine long block assembly to 15 years from the date the vehicle was first put into service or 150,000 miles, whichever occurs first for both new and subsequent vehicle owners."

and Service Managers of the updated warranty coverage for the product improvement (PI2002A). Upon completion of this Product Improvement Campaign, Kia will extend the warranty coverage for the engine long block assembly to 15 years from the date the vehicle was first put into service or 150,000 miles, whichever occurs first for both new and subsequent vehicle owners.

updated warranty coverage for the product improvement (PI2002A). Upon completion of this Product Improvement Campaign, Kia will extend the warranty coverage for the engine long block assembly to 15 years from the date the vehicle was first put into service or 150,000 miles, whichever occurs first for both new and subsequent vehicle owners.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

IMPROVEMENT (PI2002A) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

diagnosing and/or repairing some 2012-2019MY Soul (AM/PS) vehicles (refer to table below for applicable engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

is sending this notice to remind you in detail of the oil and oil filter maintenance requirements provided in your Owner's Manual which are critical to your engine's health. The purpose of sharing this information is to help you protect the investment you have in your vehicle's engine, to maximize its durability, and to avoid issues associated with insufficient or improper vehicle maintenance.

notified you that it was conducting a Product Improvement Campaign to perform a software update to protect the engine from excessive connecting rod bearing damage on the 2012-2016 MY Kia Soul vehicles equipped with the 1.6L Gasoline Direct Injection (GDI). However, due to the coronavirus (COVID-19) outbreak, we understand there may be challenges in taking your vehicle to the dealership for this update. We want to assure you that we are practicing the safety measures recommended by the CDC and local governments to maintain the best possible environments at our dealerships. The health and safety of our customers and employees are our top priority. If your Kia vehicle needs maintenance, service or repair for any reason, your local dealer is here to help and many have special programs designed to support your individual needs (details typically included on the dealers website). We would, however, like to assure you that there is no immediate need to have this software update performed. Once this challenging situation has passed, you can have this software update performed on your vehicle, and the warranty for the engine sub-assembly (short block) will be extended to 10 years from the vehicle in-service date or 120,000 miles, whichever occurs first.

Service Manager advising of a new a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on all 2012~2016 MY Soul vehicles equipped with 1.6-liter GDI engine, manufactured from July 8, 2011 through August 11, 2016.

Principals advising them of the new Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on all 2012~2016 MY Soul vehicles equipped with 1.6-liter GDI engine, manufactured from July 8, 2011 through August 11, 2016.

provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

advising of an important Product Improvement Campaign to perform a software update on all 2012-2016 MY Soul vehicles equipped with 1.6L Gasoline Direct Injection GDI engines to protect the engine from excessive connecting rod bearing damage. The software update will be done at no cost to the owner..

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

Extension Program (WTY013) - If you have incurred expense to remedy this issue prior to the date of this notice, you may have the opportunity to obtain reimbursement for that expense. You may submit your receipts online to Kia via the Owners section of www.kia.com or mail your receipts with a cover letter directly to Kia for review and consideration.

takes pride in providing you with high quality and dependable vehicles. In order to maintain these standards, Kia is extending the New Vehicle Limited Warranty coverage, to all owners of the 2012-2013 MY Soul, for the Motor Driven Power Steering (MDPS) flexible coupling from 5-years/60,000-miles to 10-years/unlimitedmiles, starting from the date of first service. The MDPS unit may experience noise when turning the steering left or right, especially while the vehicle is stopped.

VEHICLE LIMITED WARRANTY EXTENSION PROGRAM

is extending the New Vehicle Limited Warranty coverage to all owners of vehicles listed below for the Motor Driven Power Steering (MDPS) Flexible Coupling from 5-years/60,000-miles to 10-years/unlimited-miles, starting from the date of first service. The MDPS unit may experience noise when turning the steering left or right, especially while the vehicle is stopped. 2012-2013 MY Kia Soul vehicles produced from July 8, 2011 through October 2, 2013 and 2014 MY Kia Cadenza vehicles produced from February 1, 2013 through April 19, 2014.

is extending the New Vehicle Limited Warranty coverage to all owners of vehicles listed below for the Motor Driven Power Steering (MDPS) Flexible Coupling from 5-years/60,000-miles to 10-years/unlimited-miles, starting from the date of first service. The MDPS unit may experience noise when turning the steering left or right, especially while the vehicle is stopped. 2012-2013 MY Kia Soul vehicles produced from July 8, 2011 through October 2, 2013 and 2014 MY Kia Cadenza vehicles produced from February 1, 2013 through April 19, 2014.

flexible coupling in the MDPS motor of some vehicles which might experience a knock noise originating from the MDPS, when moving the steering wheel to right or left when the vehicle is stopped. This is caused by premature wear of the flexible coupling in the MDPS motor. If any knock noise from the MDPS occurs, replace the affected flexible coupling only with an improved one, following the Replacement Procedure below.

This bulletin provides information relating to all Kia vehicles equipped with Gasoline Direct Injection (GDI) engines. In these engines highly pressurized gasoline is injected via a common fuel rail and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional Multi-Point Fuel Injection (MPI) engine, the gasoline is injected into the intake port of each cylinder at a relatively low pressure. Due to high fuel pressure in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specifications for the GDI fuel system components.

inspection and installation of the steel sealing ball on: * 3.3L & 3.8L Lambda engines for 2007-2008MY Sorento (BL), * 2.0L Nu engines for 2010-2019MY Soul (AM, PS), and * 1.8L & 2.0L Nu engines for 2010-2018MY Forte (TD, YD/YDm), 2019MY~ Forte (BDm). When replacing the cylinder heads on these engines, inspect the lubrication ports for installation of the steel sealing balls. Current replacement cylinder heads may not be equipped with the required steel balls. Identify and locate the nine (9) lubricant passages on 3.3L and 3.8L engines and three (3) on 1.8L and 2.0L engines and verify a steel ball is installed in each.

bulletin provides information related to the Engine Control Unit (ECU) software upgrade for some 2012-2016MY Rio (UB), 2014-2016MY Soul (PS), and 2012-2013MY Soul (AM) vehicles, which may have a malfunction indicator light (MIL) ON with DTC P0441: Evaporative Emissions System Incorrect Purge Flow.

considered serviceable, and should be thoroughly cleaned and transferred to the new engine.

related to the Engine Control Unit (ECU) software upgrade for some 2012-2016MY Rio (UB), 2014-2016 Soul (PS), and 2012-2013MY Soul (AM) vehicles, which may have a MIL on with DTC P0441: Evaporative Emissions System Incorrect Purge Flow. To correct this condition, the ECU should be reprogrammed using the KDS download as described in this bulletin.

Engine Control Unit (ECU) software upgrade for some 2012-2016MY Rio (UB), 2014-2016 Soul (PS), and 2012-2013MY Soul (AM) vehicles, which may have a MIL on with DTC P0441: Evaporative Emissions System Incorrect Purge Flow.

GDI engine, make sure not to apply any downward pressure in the area around the Oil Control Valve (OCV) to prevent causing damage to the valve.

flexible coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped. This condition may be caused by premature wear of the flexible coupling in the MDPS.

coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped.

system is the placement of each fuel injector directly into the engine cylinder head assembly. Therefore, it is completely normal for the combustion process to create deposits on the injector spray tip surfaces.

coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped. This condition may be caused by premature wear of the flexible coupling in the MDPS.

FEATURES IN THEIR RECENTLY PURCHASED 2013 KIA VEHICLE, KIA MOTORS AMERICA WOULD LIKE ALL DEALERSHIP SERVICE PERSONNEL TO BE FAMILIAR WITH THE MODEL TIPS OUTLINED HERE TO HELP MAXIMIZE OWNER SATISFACTION WITH CERTAIN FEATURES.

SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.

THE FLEXIBLE COUPLING IN THE MDPS MOTOR OF SOME VEHICLES WHICH MIGHT EXPERIENCE A KNOCK NOISE ORIGINATING FROM THE MDPS, WHEN MOVING THE STEERING WHEEL TO RIGHT OR LEFT WHEN THE VEHICLE IS STOPPED. THIS IS CAUSED BY PREMATURE WEAR OF THE FLEXIBLE COUPLING IN THE MDPS MOTOR. IF ANY KNOCK NOISE FROM THE MDPS OCCURS, REPLACE THE AFFECTED FLEXIBLE COUPLING ONLY WITH AN IMPROVED ONE, FOLLOWING THE REPLACEMENT PROCEDURE BELOW.

WHICH MONITORS AND PREVENTS THE SIMULTANEOUS ACTIVATION OF ACCELERATOR AND BRAKE PEDALS. WHEN ENGAGED, THE FEATURE REDUCES ENGINE POWER TO IDLE. MOST CUSTOMERS WILL NEVER NOTICE THE SMART PEDAL FEATURE WHEN ACTIVE, HOWEVER, CUSTOMERS WHO TEND TO REST THEIR FOOT ON THE BRAKE PEDAL WHILE DRIVING MIGHT DESCRIBE A HESITATION OR DELAY SYMPTOM AND NOT REALIZE THAT THE EMS ELECTRONIC CONTROL MODULE IS INTERVENING, AS DESIGNED.

IS CONDUCTING A VOLUNTARY SERVICE CAMPAIGN TO ADD ADDITIONAL ANTI-CORROSION MATERIAL TO THE UNDERBODY OF ALL 2010-2013 MY SOUL VEHICLES THAT WERE ORIGINALLY SOLD IN OR ARE CURRENTLY REGISTERED IN THE STATES WHERE HEAVY AMOUNTS OF ROAD SALT ARE USED.

FLEXIBLE COUPLING IN THE MDPS MOTOR OF SOME VEHICLES WHICH MIGHT EXPERIENCE A KNOCK NOISE ORIGINATING FROM THE MDPS, WHEN MOVING THE STEERING WHEEL TO RIGHT OR LEFT WHEN THE VEHICLE IS STOPPED. THIS IS CAUSED BY PREMATURE WEAR OF THE FLEXIBLE COUPLING IN THE MDPS MOTOR. IF ANY KNOCK NOISE FROM THE MDPS OCCURS, REPLACE THE AFFECTED FLEXIBLE COUPLING ONLY WITH AN IMPROVED ONE, FOLLOWING THE REPLACEMENT PROCEDURE BELOW.

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.

This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.

Damper Clutch (D/C) Solenoid on 6-speed automatic transaxles with DTC P0741 (active or history), instead of replacing the transaxle. To reduce vehicle repair time, this procedure can be performed with the transaxle installed in the vehicle.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

THIS BULLETIN PROVIDES INFORMATION REGARDING AXLE SHAFT SERVICEABILITY FOR KIA VEHICLES EQUIPPED WITH A SIX-SPEED AUTOMATIC TRANSMISSION. REFER TO THE TABLE BELOW FOR A DETAILED LIST OF VEHICLE MODELS. INDIVIDUAL SERVICE PARTS SUCH AS AXLE BOOTS, JOINTS AND HARDWARE FOR INNER JOINT ARE NOW AVAILABLE THROUGH YOUR PARTS DEPARTMENT.

RELEARN THE ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE ECM/PCM.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE PCM/TCM. AFTER THE ADAPTIVE VALUES ARE RESET, THE TRANSMISSION COMPUTER ADAPTIVE VALUES MUST BE RELEARNED BY DRIVING IN A PRECISE MANNER TO TEACH THE COMPUTER THE PROPER SOLENOID DUTY AND LINE PRESSURE FOR THE NEW TRANSMISSION/COMPUTER COMBINATION.

identify and record the head unit software level on various head unit platforms and generations.

(ELE091) (Rev 1) - This bulletin provides the procedure on how to identify and record the head unit software level on various head unit platforms and generations. This procedure will now be required when ordering head units through the Direct Exchange Program (see Parts Bulletin 91-961-0005).

ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.

COMPATIBILITY ISSUES BETWEEN NAVIGATION HEAD UNITS AND SD CARDS WHEN REPLACING HEAD UNITS FOR MULTIMEDIA ISSUES. IF AFTER REPLACING A NAVIGATION HEAD UNIT THE ORIGINAL SD CARD DOES NOT OPERATE CORRECTLY, FOLLOW THE STEPS BELOW TO DIAGNOSE THE ISSUE:

BLUETOOTH CONCERNS WHEN USING AN IPHONE WITH IOS 8.X (IOS 8, 8.0.1, 8.0.2, 8.1, 8.1.2, 8.1.3, ETC.) WHILE PAIRED TO A HEAD UNIT.

SOFTWARE OF SOME 2013MY OPTIMA (TF/QF) AND SOME 2013MY SOUL (AM) VEHICLES, TO IMPROVE BLUETOOTH CONNECTIVITY. KIA IS REQUESTING THE COMPLETION OF THIS SERVICE ACTION ON ALL AFFECTED VEHICLES. BEFORE CONDUCTING THE PROCEDURE, VERIFY THAT THE VEHICLE IS INCLUDED IN THE LIST OF THE AFFECTED VINS.

ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.

RECORD THE HEAD UNIT SOFTWARE LEVEL ON VARIOUS HEAD UNIT PLATFORMS AND GENERATIONS. THIS PROCEDURE WILL NOW BE REQUIRED WHEN ORDERING HEAD UNITS THROUGH THE DIRECT EXCHANGE PROGRAM.

SYSTEM SOFTWARE OF SOME 2013MY SOUL (AM), OPTIMA (TF/QF), SORENTO (XMA) AND FORTE (TD) VEHICLES, TO IMPROVE BLUETOOTH CONNECTIVITY.

OPTIMA (TF/QF) AND SOME 2013MY SOUL (AM) VEHICLES, TO IMPROVE BLUETOOTH CONNECTIVITY.

(XM), OPTIMA (TF/QF), RIO (UB) AND SPORTAGE (SL) VEHICLES TO IMPROVE BLUETOOTH CONNECTIVITY.

diagnosis of the Inhibitor Switch.

CLUSTER ILLUMINATION.

USB ports and 12V power outlets to connect/charge mobile phones. Customers may experience issues with their head units that may be related to the use of aftermarket USB charging cables, including; * Electrical interference and limited or no functionality when attempting to play music, or when charging a device through the USB port * Excessive static or noise when listening to the audio source * Malfunctions and screen freeze of the head unit screen * Slow down of the system response while device is plugged in * Music will not play from iPhone 5 or 6 with Kia iPod cable and aftermarket adapter * No or limited functionality when trying to play music from an Apple device

The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.

bulletin provides information related to the ECM software upgrade for some 2012-2013MY Rio (UB) and some 2012-2013 Soul (AM) vehicles which may experience a malfunction indicator lamp (MIL) illuminated with the Electronic Control Module (ECM) system-related DTCs; P0456, P0461,P050A, P2188, P2192, P0128.

INFORMATION RELATED TO THE ECM SOFTWARE UPGRADE FOR SOME 2012~2014MY RIO (UB), SOME 2012~2013 SOUL (AM) AND SOME 2014MY SOUL (PS) VEHICLES, WHICH MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATED WITH THE ELECTRONIC CONTROL MODULE (ECM) SYSTEM-RELATED DTCS; P0456, P0461, P050A, P2188, P2192, P0128, P0326, P0441. TO CORRECT THIS CONDITION, THE ECM SHOULD BE REPROGRAMMED USING THE GDS DOWNLOAD AS DESCRIBED IN THIS BULLETIN. BEFORE PERFORMING THIS PROCEDURE FOR A SPECIFIC DTC CONCERN, VERIFY THE VIN AND DTC FALL WITHIN THE PRODUCTION RANGES, BY CONSULTING THE TABLE ON PAGE 10. FOR CONFIRMATION THAT THE LATEST REFLASH HAS BEEN DONE TO A VEHICLE YOU ARE WORKING ON, VERIFY ROM ID USING THE TABLES IN THIS TSB.

INFORMATION RELATED TO THE ECM SOFTWARE UPGRADE FOR SOME 2012~2013MY RIO (UB) AND SOME 2012~2013 SOUL (AM) VEHICLES WHICH MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATED WITH THE ELECTRONIC CONTROL MODULE (ECM) SYSTEM-RELATED DTCS; P0456, P0461, P050A, P2188, P2192, P0128, P0326, P0441. TO CORRECT THIS CONDITION, THE ECM SHOULD BE REPROGRAMMED USING THE GDS DOWNLOAD AS DESCRIBED IN THIS BULLETIN. BEFORE PERFORMING THIS PROCEDURE, VERIFY THE VIN FALLS WITHIN THE PRODUCTION RANGES BY CONSULTING THE TABLE ON PAGE 10. FOR CONFIRMATION THAT THE LATEST REFLASH HAS BEEN DONE TO A VEHICLE YOU ARE WORKING ON, VERIFY ROM ID USING THE TABLES IN THIS TSB.

INFORMATION RELATED TO THE ECM SOFTWARE UPGRADE FOR SOME 2012~2014MY RIO (UB), SOME 2012~2013 SOUL (AM) AND SOME 2014MY SOUL (PS) VEHICLES, WHICH MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATED WITH THE ELECTRONIC CONTROL MODULE (ECM) SYSTEM-RELATED DTCS; P0456, P0461, P050A, P2188, P2192, P0128, P0326, P0441. TO CORRECT THIS CONDITION, THE ECM SHOULD BE REPROGRAMMED USING THE GDS DOWNLOAD AS DESCRIBED IN THIS BULLETIN. BEFORE PERFORMING THIS PROCEDURE FOR A SPECIFIC DTC CONCERN, VERIFY THE VIN AND DTC FALL WITHIN THE PRODUCTION RANGES, BY CONSULTING THE TABLE ON PAGE 10. FOR CONFIRMATION THAT THE LATEST REFLASH HAS BEEN DONE TO A VEHICLE YOU ARE WORKING ON, VERIFY ROM ID USING THE TABLES IN THIS TSB.

THIS SPECIAL SERVICE TOOL (SST) WAS DEVELOPED TO IMPROVE THE EFFICIENCY AND EFFECTIVENESS OF UPDATING 2010MY, AND LATER, KIA AUDIO HEAD UNITS USING A GDS, AND NOW, THE SAME FUNCTIONALITY IS AVAILABLE ON KDS. SOME TECHNICIANS MAY NOT BE AWARE OF THE BENEFITS THE AUM TOOL HAS TO OFFER. THE AUM ELIMINATES THE NEED FOR MULTIPLE USB FLASH DRIVES FOR SPECIFIC VEHICLE MODELS AND APPLICATIONS WHICH, IF MISAPPLIED, MAY RESULT IN AN IMPROPER AUDIO SYSTEM SOFTWARE UPDATE AND/OR LOCKED UP HEAD UNIT. ADDITIONALLY, FIELD REPORTS HAVE INDICATED THAT USB DRIVES FOR AUDIO UPDATES ARE EASILY LOST OR MISPLACED.

LAMP (MIL) THAT ILLUMINATES AND ECM NEEDS REPROGRAMMING WITH LATEST GDS DOWNLOAD. MODEL 2012-14 RIO, 2012-14 SOUL. *PE

THE ILLUMINATION OF THE MALFUNCTION INDICATOR LAMP WITHIN THE ELECTRONIC CONTROL MODULE (ECM) SYSTEM WHICH SHOULD BE REPROGRAMMED. MODEL 2012-13 RIO, SOUL. *PE

a new Special Service Tool (SST) (A) developed to prevent the hood release lever pivot point (B) from being damaged when removing the hood release lever. Follow the instructions included in this bulletin to properly remove the hood release lever using the new SST.

DEBRIS ACCUMULATION ON THE WINDSHIELD WASHER PUMP INLET FILTER. OVER TIME, SOME KIA VEHICLES MAY EXHIBIT A LIMITED APPLICATION OF WINDSHIELD WASHER FLUID WHEN THE WASHER FUNCTION IS USED. LIMITED APPLICATION OF WINDSHIELD WASHER FLUID CAN BE CAUSED BY FOREIGN DEBRIS ON THE WASHER PUMP INLET FILTER. TO CORRECT THIS CONDITION, REPLACE THE WASHER PUMP INLET FILTER AND PERFORM THE WINDSHIELD WASHER RESERVOIR FLUSHING PROCEDURE OUTLINED IN THIS TSB.

FOLLOWING MANNER.

INSPECT AND/OR REPLACE THE INTERIOR DOOR HANDLE(S) OF SOME 2013MY SOUL (AM) VEHICLES, PRODUCED FROM AUGUST 1, 2012 THROUGH SEPTEMBER 30, 2013, WHICH MAY EXHIBIT PEELING OF THE CHROME FINISH ON THE DOOR HANDLE (AS SHOWN BELOW). TO CORRECT THIS CONDITION, KIA IS REQUESTING THE COMPLETION OF THIS SERVICE ACTION ON ALL AFFECTED VEHICLES. BEFORE CONDUCTING THE PROCEDURE, VERIFY THE VEHICLE IS INCLUDED IN THE LIST OF AFFECTED VINS.

MODEL 2004-09 SPECTRA, 2006-10 OPTIMA, 2006-11 RIO 2007-10 RONDO AND 2010-13 SOUL. *PE

owners advising them to have the Product Improvement campaign PI2002A performed.

owners advising them to have the Product Improvement campaign PI2002A performed.

the Product Improvement Campaign.

CAMERA OF SOME KIA VEHICLES (SEE TABLE ON PG. 6 FOR SPECIFIC MODELS AND PRODUCTION DATES) WHICH MAY EXHIBIT INADEQUATE IMAGE QUALITY FROM THE REAR VIEW CAMERA. DIAGNOSE THE CONCERNS USING THE INFORMATION IN THIS BULLETIN AND, IF NECESSARY, REPLACE THE REAR VIEW CAMERA WITH AN IMPROVED PART BY FOLLOWING THE APPLICABLE SERVICE PROCEDURE ON KGIS.

now making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

now making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

once fully attached, are utilized in various Kia models and are strictly intended for ?one time use.? Some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.? It is critical for technicians to be aware that ALL such locking fasteners, regardless of type, are for ?one time use? only.

strictly intended for ?one time use?. Though not limited to the following, some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.?

regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.

article for detailed information on applicable models, model year and system supplier; along with the applicable Hotline contact information and business hours.

incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.

CONTROLLER SOFTWARE UPGRADE FOR 2012-13MY SOUL (AM) VEHICLES, PRODUCED FROM JULY 11, 2011 TO JUNE 22, 2012, AND EQUIPPED WITH MANUAL HVAC CONTROLS. REVISED.

THIS BULLETIN PROVIDES THE PROCEDURE FOR UPGRADING THE 2013MY SOUL UVO SYSTEM. KIA IS REQUESTING THE COMPLETION OF THIS SERVICE ACTION ON ALL AFFECTED 2013MY SOUL VEHICLES PRIOR TO DELIVERY. BEFORE CONDUCTING THE PROCEDURE, VERIFY THAT THE VEHICLE IS INCLUDED IN THE LIST OF THE AFFECTED VINS

UPGRADING THE KIA UVO (YOUR VOICE) SYSTEM. KIA UVO OWNERS HAVE THE OPTION TO DOWNLOAD AVAILABLE UPGRADES DIRECTLY FROM THE KIA.COM WEBSITE AND CAN PERFORM THE UPGRADE THEMSELVES OR HAVE THE DEALER PERFORM THE UPGRADE IN WHICH CASE ADDITIONAL LABOR CHARGES MAY APPLY. FOR CUSTOMERS WHO PERFORM THEIR OWN UPGRADE, KIA PROVIDES THE CUSTOMER WITH SOFTWARE AND UPGRADE INSTRUCTIONS. IF THE CUSTOMER OPTS TO HAVE THE DEALER PERFORM THE UPGRADE, THE UPGRADE PROCEDURE IS OUTLINED IN THIS BULLETIN.

illuminated with DTC(s) P0442, P0455, P0456, or P0457 (Evaporative Emissions System-Leak detected) and the evaporative (EVAP) leak self-test resulted in NTF, a manual EVAP test is recommended.