2013 Kia Sorento TSBs

(CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)

(CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2002A, PI2002B and SC200**1) titled Knock Sensor Detection System - ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1803 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

test procedure of the Bearing Clearance Tester (BCT) Special Service Tool (SST). The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.

to address a no-start or hard start with poor running condition after engine replacement under PI1802Y/Z or PI1803Y/Z. Some replacement long blocks may come with pre-installed fuel rail, injectors, and injector wiring harness. If the condition is present, it is possible that the injector harness was not installed correctly. The connections may be swapped from cylinder No. 1 and cylinder No. 4, and from cylinder No. 2 and cylinder No. 3.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1803 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1803 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2002A, PI2002B and SC200**1) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

IMPROVEMENT (PI1803) - This bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1803, Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1803, Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement".

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1803, Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

- SUPERSEDED BY PI1802YZ/1803YZ.

revised to include additional information.This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1803, Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

has been superseded by PI1803Y/Z.

revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1803, Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in November 2018 (PI1803, Rev 1, 01/02/2018) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

IMPROVEMENT (PI1803) - This bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

the partial repair of the Four Wheel Drive (4WD) Coupling Assembly, Pressure Sensor, Actuator Motor or 4WD harness on some 2011-2020 Sportage (SL, QL) and 2013-2020MY Sorento (XMa, UMa) 4WD vehicles for a concern regarding: Oil leakage from the 4WD coupling assembly 4WD Malfunction and MIL lamp ON with DTCs Abnormal noise or vibration while driving

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

This bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage

information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

takes pride in providing you with high quality and dependable vehicles. In order to maintain these standards, Kia is extending the New Vehicle Limited Warranty coverage, to all owners of 2011-2013 MY Kia Sorento vehicles, for the halogen headlamp low beam connector wiring harness from 5-years/60,000-miles to 10-years/unlimited-miles, starting from the date of first service. The headlamp connectors may lose electrical contact with a low beam bulb in one of the headlamp assemblies. This condition on the affected headlamp does not affect the other low beam. In addition, the high beams continue to function at all times.

is extending the New Vehicle Limited Warranty coverage to all owners of the 2011-2013 MY Kia Sorento vehicles, produced from October 24, 2009 through January 31, 2013, for the halogen headlamp low beam connector wiring harness from 5-years/60,000-miles to 10-years/unlimited-miles, starting from the date of first service. The headlamp connectors may lose electrical contact with a low beam bulb in one of the headlamp assemblies. This condition on the affected headlamp does not affect the other low beam. In addition, the high beams continue to function at all times.

is extending the New Vehicle Limited Warranty coverage to all owners of the 2011-2013 MY Kia Sorento vehicles, produced from October 24, 2009 through January 31, 2013, for the halogen headlamp low beam connector wiring harness from 5-years/60,000-miles to 10-years/unlimited-miles, starting from the date of first service. The headlamp connectors may lose electrical contact with a low beam bulb in one of the headlamp assemblies. This condition on the affected headlamp does not affect the other low beam. In addition, the high beams continue to function at all times.

related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.

related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.

Service Bulletin previously published in November 2018 (PI1803, Rev 1, 01/02/2018) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

Service Bulletin previously published in November 2018 (PI1803, Rev 1, 01/02/2018) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

is conducting an important Product Improvement Campaign to perform a software update on 2012-2014 MY Sorento vehicles equipped with 2.4L Gasoline Direct Injection ("GDI") engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").

to include additional information.This bulletin provides information related to the Technical Service Bulletin previously published in November 2018 (PI1803, Rev 1, 01/02/2018) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.

to include additional information This bulletin provides information related to the Technical Service Bulletin previously published in November 2018 (PI1803, Rev 1, 01/02/2018) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.

revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

This bulletin provides information relating to all Kia vehicles equipped with Gasoline Direct Injection (GDI) engines. In these engines highly pressurized gasoline is injected via a common fuel rail and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional Multi-Point Fuel Injection (MPI) engine, the gasoline is injected into the intake port of each cylinder at a relatively low pressure. Due to high fuel pressure in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specifications for the GDI fuel system components.

information related to the Technical Service Bulletin previously published in November 2018 (PI1803) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.

Service Bulletin for the new Product Improvement Campaign to provide information regarding a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

document is the Q & A for the new Product Improvement Campaign to provide information regarding a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

is conducting an important Product Improvement Campaign to perform a software update on 2012-2014 MY Sorento vehicles equipped with 2.4L Gasoline Direct Injection (?GDI?) engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (?ECU?).

is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

considered serviceable, and should be thoroughly cleaned and transferred to the new engine.

and, if necessary, replacement of the engine assembly on certain 2011 to 2014 model year Optima, Sorento, and Sportage vehicles. For repair information please refer to Technical Service Bulletin SC147.

II Engine Inspection and/or Replacement and is provided to dealers for specific guidance with claim administration and processing of SC147 warranty claims.

necessary, replacement of the engine assembly on certain 2011 to 2014 model year Optima, Sorento, and Sportage vehicles.

is conducting a Voluntary Service Campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento vehicles that were originally sold in or are currently registered in the states where heavy amounts of road salt are used.

will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.

will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.

for some 2012~2015MY Optima (QF) vehicles, produced from August 12, 2011 to October 2, 2015, some 2012~2015MY Sorento (XMa) vehicles, produced from April 19, 2011 to December 11, 2014, some 2011~2015MY Optima (TF) vehicles, produced from August 12, 2010 to July 23, 2015, and some 2014~2016MY Sportage (SL) vehicles, produced from September 30, 2013 to November 16, 2015, which may experience a malfunction indicator lamp (MIL) illuminated with the Electronic Control Unit (ECU) system-related DTC(s): P0420 and possibly P0171. This concern occurs most commonly during prolonged engine braking while descending a steep grade.

Malfunction Indicator Lamp (MIL) may illuminate with the ECM system-related DTC P0269. To correct this concern, replace the fuel injector in cylinder number three (3) by referring to the Service Information on KGIS.

vehicles, equipped with the 3.5 L engine and produced from October 26, 2009 to July 14, 2012, which may exhibit a concern related to unusually loud engine chatter during initial start-up after sitting for several hours.

In some cases, oil may leak from the filter housings where they mate with the block, or from the oil pressure switch.

related to the ECM software upgrade for some 2011-2013MY Sorento 3.5L MPI vehicles, produced from October 25, 2009 through January 31, 2013, and 2011, 2012 & 2014MY Sedona 3.5L MPI vehicles, produced from March 03, 2010 through July 12, 2013, which may experience a Malfunction Indicator Lamp illuminated with the ECM (Electronic Control Module) system-related DTC P0638.

equipped with a 3.5L MPI engine, which may exhibit a Malfunction Indicator Lamp (MIL) with DTC P200A,

for some 2012~2015MY Optima (QF) vehicles, produced from August 12, 2011 to October 2, 2015, some 2012~2015MY Sorento (XMa) vehicles, produced from April 19, 2011 to December 11, 2014, some 2011~2015MY Optima (TF) vehicles, produced from August 12, 2010 to July 23, 2015, and some 2014~2016MY Sportage (SL) vehicles, produced from September 30, 2013 to November 16, 2015, which may experience a malfunction indicator lamp (MIL) illuminated with the Electronic Control Unit (ECU) system-related DTC(s): P0420 and possibly P0171. This concern occurs most commonly during prolonged engine braking while descending a steep grade.

with a 2.4L GDI engine, it is important to note that the DTC may recur after replacement of any faulty component(s) and resetting adaptive values. See this Article for information on resetting cylinder balance adaptation values.

is conducting a Voluntary Service Campaign to reprogram the Engine Control Module in certain 2011-2013 model year Sorento vehicles.

is conducting a Voluntary Service Campaign to upgrade the Engine Control Module (?ECM?) logic on certain 2011-2013 MY Kia Sorento vehicles equipped with the 3.5 liter engine and an alternator supplied by Remy.

is conducting a Voluntary Service Campaign on certain 2011-2013 MY Sorento vehicles with the 3.5 liter engine, to upgrade the Engine Control Module (?ECM?) Logic.

system is the placement of each fuel injector directly into the engine cylinder head assembly. Therefore, it is completely normal for the combustion process to create deposits on the injector spray tip surfaces.

related to an upgrade of the ECM software on some 2011~2013MY Sorento (XMa) vehicles, produced from July 12, 2010 through January 31, 2013. During a specific set of operating conditions, it is possible under rare circumstances when braking and bringing the vehicle to a stop, for the engine to also stop.

coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped. This condition may be caused by premature wear of the flexible coupling in the MDPS.

covers on some 2011-2013MY Sorento (XM) vehicles, produced from October 26, 2009 through January 21, 2013, which may exhibit a condition related to oil leakage and/or noise emanating from the front struts.

IS EXTENDING THE WARRANTY COVERAGE FOR THE DRIVERS FRONT AIRBAG CLOCK SPRING ASSEMBLY ON THE 2011-2015 MY SORENTO VEHICLES, MANUFACTURED FROM 10/24/2009 THROUGH 12/17/2014, TO FIFTEEN (15) YEARS WITH UNLIMITED MILEAGE, STARTING FROM THE DATE OF FIRST SERVICE. THE CLOCK SPRING IS AN ELECTRICAL CONNECTION WHICH ROTATES WITH THE STEERING WHEEL TO MAINTAIN PROPER FUNCTIONING OF THE AIRBAG UNIT. KIAS SYSTEM IS DESIGNED TO ILLUMINATE THE AIRBAG WARNING LIGHT WHEN ELECTRICAL RESISTANCE INCREASES, WHICH CAN BE CONTRIBUTED TO BY USAGE PATTERNS AND ENVIRONMENTAL CONDITIONS. ILLUMINATION OF THE AIRBAG WARNING LIGHT ADVISES THE DRIVER TO HAVE THE SYSTEM INSPECTED AND REPAIRED. IF CONTINUED TO BE USED WITHOUT REPAIR, THE DRIVERS AIRBAG MAY EVENTUALLY NOT DEPLOY IN A FRONTAL IMPACT.

ELIGIBLE FOR REIMBURSEMENT FOR SOME OR ALL OF THAT EXPENSE. MAIL THIS COMPLETED REQUEST FOR REIMBURSEMENT FORM TO KIA, ALONG WITH DOCUMENTATION SPECIFIED BELOW, FOR REVIEW AND CONSIDERATION AT THE FOLLOWING ADDRESS: CONSUMER ASSISTANCE CENTER, KIA MOTORS AMERICA, INC., P.O. BOX 52410, IRVINE, CA 92619-2410

IS EXTENDING THE WARRANTY COVERAGE FOR THE DRIVERS FRONT AIRBAG CLOCK SPRING ASSEMBLY ON 2011-2015 MY SORENTO VEHICLES, MANUFACTURED FROM 10/24/2009 THROUGH 12/17/2014, TO FIFTEEN (15) YEARS WITH UNLIMITED MILEAGE, STARTING FROM THE DATE OF FIRST SERVICE. THE CLOCK SPRING IS AN ELECTRICAL CONNECTION WHICH ROTATES WITH THE STEERING WHEEL TO MAINTAIN PROPER FUNCTIONING OF THE AIRBAG UNIT. THIS WARRANTY EXTENSION ADDRESSES FAILURES OF THE DRIVERS FRONT AIRBAG CLOCK SPRING AS REPORTED BY SOME VEHICLE OWNERS, AS WELL AS THE DIAGNOSIS OF ANY CONCERNS RELATED TO THE AIRBAG WARNING LIGHT.

FEATURES IN THEIR RECENTLY PURCHASED 2013 KIA VEHICLE, KIA MOTORS AMERICA WOULD LIKE ALL DEALERSHIP SERVICE PERSONNEL TO BE FAMILIAR WITH THE MODEL TIPS OUTLINED HERE TO HELP MAXIMIZE OWNER SATISFACTION WITH CERTAIN FEATURES.

NEW/REVISED SECTIONS OF THIS BULLETIN ARE INDICATED BY A BLACK BAR IN THE MARGIN.THIS BULLETIN PROVIDES INFORMATION RELATED TO THE ECM SOFTWARE UPGRADE AND ALTERNATOR PULLEY REPLACEMENT FOR SOME 2013MY SORENTO VEHICLES, PRODUCED FROM FEBRUARY 16, 2012 TO SEPTEMBER 13, 2012, TO IMPROVE IDLE RPM STABILITY (750 TO 680) WHILE AT A STOP WITH A/C ON. IT IS IMPORTANT TO NOTE THAT THE 2.4L GDI ENGINE HAS A CERTAIN LEVEL OF HARMONIC VIBRATION WHILE AT LOW IDLE RPM WHICH IS A NORMAL CHARACTERISTIC OF THIS ENGINE DESIGN. FOR CONFIRMATION THAT THE LATEST REFLASH HAS BEEN PERFORMED TO A VEHICLE YOU ARE WORKING ON, VERIFY ROM ID USING THE TABLES IN THIS TSB.

SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.

BY DRAWING INTERIOR VEHICLE AIR TEMPERATURE THROUGH THE SEATING SURFACES. THE CUSTOMER PERCEPTION MAY BE THAT THE SEAT IS AIR CONDITIONED AND THE SEAT IS NOT GETTING COLD ENOUGH HOWEVER THE ACTUAL DESIGN INTENT IS TO DRAW AMBIENT AIR THROUGH THE SEAT WITH A SEPARATE BLOWER MOTOR ATTACHED TO THE SEAT ASSEMBLY.

SOME 2012-2013 MY SORENTO(XM) AND 2012 MY SEDONA(VQ) VEHICLES WHICH MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP ILLUMINATED (MIL) WITH THE ECM (ELECTRONIC CONTROL MODULE) SYSTEM-RELATED CYLINDER CONTRIBUTION/BALANCE DTC(S), (P0263, P0266, P0269, P0272, P0275, P0278).

MOTORS AMERICA TAKES PRIDE IN PROVIDING YOU WITH HIGH QUALITY AND DEPENDABLE VEHICLES. IN ORDER TO MAINTAIN THESE STANDARDS, KIA IS EXTENDING THE WARRANTY COVERAGE, TO ALL OWNERS, FOR THE ENGINES SHORT BLOCK ASSEMBLY ON 2012-2014 MY SORENTO 2.4L GDI ENGINE TO 10 YEARS STARTING FROM THE DATE OF FIRST SERVICE OR 120,000 MILES, WHICHEVER COMES FIRST. THE SHORT BLOCK CONSISTS OF THE ENGINE BLOCK, CRANKSHAFT AND BEARINGS, CONNECTING RODS AND BEARINGS AND PISTONS. THIS WARRANTY EXTENSION ADDRESSES ISSUES WITH CONNECTING ROD WEAR WHICH RESULTS IN KNOCKING NOISE FROM THE ENGINE. THE KNOCKING NOISE INCREASES IN FREQUENCY AS THE ENGINE RPM INCREASES. IF THE VEHICLE CONTINUES TO BE DRIVEN WITH A WORN CONNECTING ROD BEARING, THE BEARING CAN FAIL AND MAY RESULT IN ENGINE FAILURE.

PAID TO HAVE YOUR ENGINE REPAIRED/REPLACED DUE TO CONNECTING ROD FAILURE, YOU MAY BE ELIGIBLE FOR REIMBURSEMENT FOR SOME OR ALL OF THAT EXPENSE. MAIL THIS COMPLETED REQUEST FOR REIMBURSEMENT FORM TO KIA, ALONG WITH DOCUMENTATION SPECIFIED BELOW, FOR REVIEW AND CONSIDERATION TO THE FOLLOWING ADDRESS: CONSUMER ASSISTANCE CENTER, KIA MOTORS AMERICA, INC., P.O. BOX 52410, IRVINE, CA 92619-2410, 1-800-333-4542

HAS EXTENDED THE WARRANTY COVERAGE OF THE KIA NEW VEHICLE LIMITED WARRANTY FOR THE SHORT BLOCK ASSEMBLY (ENGINE BLOCK, CRANKSHAFT AND BEARINGS, CONNECTING RODS AND BEARINGS AND PISTONS) ON 2012-2014 MY SORENTO 2.4L GDI ENGINE TO 10 YEARS STARTING FROM THE DATE OF FIRST SERVICE OR 120,000 MILES, WHICHEVER COMES FIRST, REGARDLESS OF WHETHER THE VEHICLE OWNER IS AN ORIGINAL OR SUBSEQUENT VEHICLE OWNER. THE PURPOSE OF THIS WARRANTY EXTENSION IS TO ADDRESS ISSUES WITH CONNECTING ROD AND BEARING WEAR THAT CAN LEAD TO ENGINE FAILURE.

WHICH MONITORS AND PREVENTS THE SIMULTANEOUS ACTIVATION OF ACCELERATOR AND BRAKE PEDALS. WHEN ENGAGED, THE FEATURE REDUCES ENGINE POWER TO IDLE. MOST CUSTOMERS WILL NEVER NOTICE THE SMART PEDAL FEATURE WHEN ACTIVE, HOWEVER, CUSTOMERS WHO TEND TO REST THEIR FOOT ON THE BRAKE PEDAL WHILE DRIVING MIGHT DESCRIBE A HESITATION OR DELAY SYMPTOM AND NOT REALIZE THAT THE EMS ELECTRONIC CONTROL MODULE IS INTERVENING, AS DESIGNED.

IS CONDUCTING A VOLUNTARY SERVICE CAMPAIGN TO UPDATE THE ENGINE CONTROL UNIT (ECU) IN CERTAIN 2012-2014 MY SORENTO VEHICLES WHICH COULD OTHERWISE EXPERIENCE A DECREASE IN ACCELERATION ACCOMPANIED BY THE ILLUMINATION OF THE CHECK ENGINE OR MALFUNCTION INDICATOR LAMP (MIL).

WILL BE CONDUCTING A VOLUNTARY SERVICE CAMPAIGN TO UPDATE THE ENGINE CONTROL UNIT (ECU) IN CERTAIN 2012-2014 MY SORENTO, 2012-2013 MY OPTIMA, AND 2012-2013 MY SPORTAGE VEHICLES EQUIPPED WITH THE 2.4L AND 2.0L TURBO GDI ENGINES. THE SUBJECT VEHICLES ENGINES ARE EQUIPPED WITH A GASOLINE DIRECT INJECTION (GDI) SYSTEM THAT UTILIZES A FLOW CONTROL VALVE (FCV) TO CONTROL THE SUPPLY OF FUEL. THE FCV NEEDLE MAY EXPERIENCE EXCESSIVE WEAR, EVENTUALLY RESULTING IN IMPAIRMENT OF FUEL FLOW. IF THAT HAPPENS, AND TO PROTECT THE ENGINE, THE ECU MAY REDUCE ENGINE ACCELERATION WHILE ILLUMINATING THE CHECK ENGINE OR MALFUNCTION INDICATOR LAMP (MIL). THE ECU UPDATE WILL IMPROVE THE DURABILITY AND OPERATION OF THE FCV NEEDLE.

AN ECM SOFTWARE UPDATE FOR THE ENGINE CONTROL UNIT (ECU) IN CERTAIN 2012~2014MY SORENTO, 2012~2013MY OPTIMA, AND 2012~2013MY SPORTAGE VEHICLES EQUIPPED WITH THE 2.4L AND 2.0L TURBO GDI ENGINES. THE SUBJECT VEHICLES ENGINES ARE EQUIPPED WITH A GASOLINE DIRECT INJECTION (GDI) SYSTEM THAT UTILIZES A FLOW CONTROL VALVE (FCV) TO CONTROL THE SUPPLY OF FUEL. THE FCV NEEDLE MAY EXPERIENCE EXCESSIVE WEAR, EVENTUALLY RESULTING IN IMPAIRMENT OF FUEL FLOW. IF THAT HAPPENS, AND TO PROTECT THE ENGINE, THE ECU MAY REDUCE ENGINE ACCELERATION WHILE ILLUMINATING THE CHECK ENGINE OR MALFUNCTION INDICATOR LAMP (MIL). THE ECU UPDATE WILL IMPROVE THE DURABILITY AND OPERATION OF THE FCV NEEDLE.

ENGINE MISFIRE WITH A MALFUNCTION INDICATOR LIGHT (MIL) ON IN THE DASH, CHECK FOR THE PRESENCE OF DTC P0315 CRANKSHAFT POSITION SENSOR (CKP) VARIATION NOT LEARNED. USE THE VMI TO VIEW THE SCOPE PATTERN OF THE CRANKSHAFT POSITION SENSOR SIGNAL. VERIFY A GOOD EQUAL CRANKSHAFT SENSOR PATTERN IS PRESENT WITH NO DIPS OR VARIATION, AS SHOWN IN FIGURE A, IN THE SIGN WAVE PATTERN. IF THE PATTERN IS IDENTICAL TO FIGURE A, USE GDS/KDS TO PERFORM A CRANK SENSOR RELEARN PROCEDURE. IF THE PATTERN SHOWS A DIP OR VARIATION, AS SHOWN IN FIGURE B, REPLACE THE FLEX PLATE TO RESOLVE THE CONCERN.

SOME VEHICLES, OR AN INOPERATIVE VALVE LINKAGE IN THE INTAKE MANIFOLD ASSEMBLY. MODELS 2011-2013 SORENTO. *PE

MAIN SEAL OR OIL PAN, WHEN ACTUAL LEAKS COMING FROM ENGINE VALLEY,OIL FILTER HOUSING, OIL PRESSURE SWITCH, AND/OR GASKETS. *PE

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 20132015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2023MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

USB ports and 12V power outlets to connect/charge mobile phones. Customers may experience issues with their head units that may be related to the use of aftermarket USB charging cables, including; * Electrical interference and limited or no functionality when attempting to play music, or when charging a device through the USB port * Excessive static or noise when listening to the audio source * Malfunctions and screen freeze of the head unit screen * Slow down of the system response while device is plugged in * Music will not play from iPhone 5 or 6 with Kia iPod cable and aftermarket adapter * No or limited functionality when trying to play music from an Apple device

LIMITED WARRANTY EXTENSION

The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.

clean, and seal, or if necessary, replace the rear wheel speed sensor housing covers on certain 2011-2015 MY Sorento 2-Wheel Drive (2WD) vehicles originally purchased and/or currently registered in the coastal states of Alabama, Florida, Georgia, Hawaii, Louisiana, Mississippi, North Carolina, South Carolina, and Texas.

Campaign to inspect, clean, and seal, or if necessary, replace the rear wheel speed sensor housing covers on certain 2011 - 2015 MY Sorento 2-Wheel Drive vehicles originally purchased and/or currently registered in the coastal states of Alabama, Florida, Georgia, Hawaii, Louisiana, Mississippi, North Carolina, South Carolina, and Texas.

clean, and seal, or if necessary, replace the rear wheel speed sensor housing covers on certain 2011 - 2015 MY Sorento 2-Wheel Drive vehicles originally purchased and/or currently registered in the coastal states of Alabama, Florida, Georgia, Hawaii, Louisiana, Mississippi, North Carolina, South Carolina, and Texas.

temperature sensor of some 2011-2014MY Optima (TF/QF) and 2011-2013MY Sorento (XMa) vehicles ONLY (see production dates on Page 3), which may experience freezing of condensation on the evaporator core and the following A/C performance related concerns below. Do NOT refer to this bulletin or the resistance specifications listed in this bulletin for ANY other models.

The same heaters are used in the cushions of both seats, but the RH cushion has a body sensor mat applied over the heater, resulting in less heat reaching the front passenger.

Navigation, then see wiring diagram for ?Back-Up Lamps? and you will see the Back-Up input into the audio unit. Also verify the reverse lamps operate as one of your first checks.

If the battery fails the test then it should be replaced and the VCMA relearn procedure should be performed with the GDS.

Sportage (SL), Sorento (XM) and Cadenza (VG) vehicles, which may experience a malfunction indicator lamp (MIL) illuminated with the ECM (Electronic Control Module) system-related DTC P0087.

SPRING ASSEMBLY TO 15 YEARS WITH UNLIMITED MILEAGE, STARTING FROM THE DATE OF FIRST SERVICE. THE CLOCKSPRING IS AN ELECTRICAL CONNECTION WHICH ROTATES WITH THE STEERING WHEEL TO MAINTAIN PROPER FUNCTIONING OF THE AIRBAG UNIT. KIAS SYSTEM IS DESIGNED TO ILLUMINATE THE AIRBAG WARNING LIGHT WHEN ELECTRICAL RESISTANCE INCREASES, WHICH CAN BE CONTRIBUTED TO BY USAGE PATTERNS AND ENVIRONMENTAL CONDITIONS. ILLUMINATION OF THE AIRBAG WARNING LIGHT, ADVISES YOU TO HAVE THE SYSTEM INSPECTED AND REPAIRED. IF CONTINUED TO BE USED WITHOUT REPAIR, THE DRIVERS AIRBAG MAY EVENTUALLY NOT DEPLOY IN A FRONTAL IMPACT.

- THIS BULLETIN PROVIDES INFORMATION RELATED TO THE REPLACEMENT OF THE DRIVERS FRONT AIRBAG CLOCK SPRING ASSEMBLY ON THE 2011-2015 MY SORENTO VEHICLES, MANUFACTURED FROM 10/24/2009 THROUGH 12/17/2014. THE CLOCK SPRING IS AN ELECTRICAL CONNECTION WHICH ROTATES WITH THE STEERING WHEEL TO MAINTAIN PROPER FUNCTIONING OF THE AIRBAG UNIT. KIAS SYSTEM IS DESIGNED TO ILLUMINATE THE AIRBAG WARNING LIGHT WHEN ELECTRICAL RESISTANCE INCREASES, WHICH CAN BE CONTRIBUTED TO BY USAGE PATTERNS AND ENVIRONMENTAL CONDITIONS. ILLUMINATION OF THE AIRBAG WARNING LIGHT ADVISES THE DRIVER TO HAVE THE SYSTEM INSPECTED AND REPAIRED. IF CONTINUED TO BE USED WITHOUT REPAIR, THE DRIVERS AIRBAG MAY EVENTUALLY NOT DEPLOY IN A FRONTAL IMPACT. KIA IS EXTENDING THE WARRANTY COVERAGE FOR THE DRIVERS FRONT AIRBAG CLOCK SPRING ASSEMBLY ON THE 2011-2015 MY SORENTO VEHICLES, MANUFACTURED FROM 10/24/2009 THROUGH 12/17/2014, TO FIFTEEN (15) YEARS WITH UNLIMITED MILEAGE, STARTING FROM THE DATE OF FIRST SERVICE. THIS WARRANTY EXTENSION ADDRESSES FAILURES OF THE DRIVERS FRONT AIRBAG CLOCK SPRING AS REPORTED BY SOME VEHICLE OWNERS, AS WELL AS THE DIAGNOSIS OF ANY CONCERNS RELATED TO THE AIRBAG WARNING LIGHT.

TEMPERATURE SENSOR OF SOME OPTIMA (TF/QF) AND SORENTO (XMA) VEHICLES (SEE PRODUCTION DATES ON PAGE 3), WHICH MAY EXPERIENCE FREEZING OF CONDENSATION ON THE EVAPORATOR CORE AND THE FOLLOWING A/C PERFORMANCE RELATED CONCERNS.

SOME OF SORENTO (XMA) VEHICLES, PRODUCED FROM JOB #1 THROUGH APRIL 4TH, 2012, WHICH MAY EXPERIENCE A DIAGNOSTIC TROUBLE CODE (DTC) (C1206 ~ C1211) DUE TO POSSIBLE WATER INTRUSION INTO THE REAR WHEEL SPEED SENSOR.

THIS SPECIAL SERVICE TOOL (SST) WAS DEVELOPED TO IMPROVE THE EFFICIENCY AND EFFECTIVENESS OF UPDATING 2010MY, AND LATER, KIA AUDIO HEAD UNITS USING A GDS, AND NOW, THE SAME FUNCTIONALITY IS AVAILABLE ON KDS. SOME TECHNICIANS MAY NOT BE AWARE OF THE BENEFITS THE AUM TOOL HAS TO OFFER. THE AUM ELIMINATES THE NEED FOR MULTIPLE USB FLASH DRIVES FOR SPECIFIC VEHICLE MODELS AND APPLICATIONS WHICH, IF MISAPPLIED, MAY RESULT IN AN IMPROPER AUDIO SYSTEM SOFTWARE UPDATE AND/OR LOCKED UP HEAD UNIT. ADDITIONALLY, FIELD REPORTS HAVE INDICATED THAT USB DRIVES FOR AUDIO UPDATES ARE EASILY LOST OR MISPLACED.

HIGH PRESSURE FUEL PUMP, FUEL DELIVERY PIPE AND MOUNTING BOLTS WOULD BE REPLACED, IF NECESSARY. MODEL 2011-2014 OPTIMA, SPORTAGE, SORENTO, CADENZA. *PE

MODULE (ECM) SYSTEM WHICH NEEDS TO HAVE SOFTWARE UPGRADED TO CORRECT OR PREVENT THIS CONDITION. MODELS 2011-2013 SORENTO, 2011-2012 AND 2014 SEDONA. *PE UPDATED 2/25/14. *PE

for specific handling procedures regarding SC147.

Sorento (XMa) vehicles, produced from October 26, 2009 to November 5, 2012, which may exhibit a concern related to the second row seats being inoperative or difficult to release.

power up.

2011-2013MY SORENTO (XMA) VEHICLES, PRODUCED FROM OCTOBER 26, 2009 TO NOVEMBER 5, 2012, WHICH MAY EXHIBIT A CONCERN RELATED TO THE SECOND ROW SEATS BEING INOPERATIVE OR DIFFICULT TO RELEASE.

ON OPTIMA (QF) AND SORENTO (XMA).

CAMERA OF SOME KIA VEHICLES (SEE TABLE BELOW FOR SPECIFIC MODELS AND PRODUCTION DATES) WHICH MAY EXHIBIT INADEQUATE IMAGE QUALITY FROM THE REAR VIEW CAMERA.

REFER TO CHA051.

*LJ

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

with the All-Wheel-Drive (AWD) system due to tire sizes of differing circumference. Some customers may complain of a chatter sensation felt in the drivetrain of the vehicle and/or the failure of drivetrain component(s). A difference in tire size (width, aspect ratio, construction, rim diameter etc.) may be the cause.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.

This bulletin provides the procedure to replace the steering gear box yoke plug and assembly on some models listed below, which may exhibit a ticking noise while turning the steering wheel with the vehicle stopped. This condition is caused by a worn lining on the steering gear box yoke assembly. Follow the procedure outlined in this bulletin to replace the steering gear box yoke plug and assembly with updated parts.

This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.

Damper Clutch (D/C) Solenoid on 6-speed automatic transaxles with DTC P0741 (active or history), instead of replacing the transaxle. To reduce vehicle repair time, this procedure can be performed with the transaxle installed in the vehicle.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

THIS BULLETIN PROVIDES INFORMATION REGARDING AXLE SHAFT SERVICEABILITY FOR KIA VEHICLES EQUIPPED WITH A SIX-SPEED AUTOMATIC TRANSMISSION. REFER TO THE TABLE BELOW FOR A DETAILED LIST OF VEHICLE MODELS. INDIVIDUAL SERVICE PARTS SUCH AS AXLE BOOTS, JOINTS AND HARDWARE FOR INNER JOINT ARE NOW AVAILABLE THROUGH YOUR PARTS DEPARTMENT.

RELEARN THE ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE ECM/PCM.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE PCM/TCM. AFTER THE ADAPTIVE VALUES ARE RESET, THE TRANSMISSION COMPUTER ADAPTIVE VALUES MUST BE RELEARNED BY DRIVING IN A PRECISE MANNER TO TEACH THE COMPUTER THE PROPER SOLENOID DUTY AND LINE PRESSURE FOR THE NEW TRANSMISSION/COMPUTER COMBINATION.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace the front passenger Occupant Detection System (ODS) Sensor Pad on 2011-2015MY Sorento (XMa) vehicles produced from September 24, 2009 through December 11, 2014. If the Occupant Detection System (ODS) Sensor Pad is not operating properly, the airbag warning light will illuminate and certain specific DTC(s) listed in this bulletin may be stored:

on the Occupant Detection System Sensor Pad to fifteen (15) years with unlimited mileage, starting from the date the vehicle was first put into service.

on the Occupant Detection System Sensor Pad to fifteen (15) years with unlimited mileage, starting from the date the vehicle was first put into service.

Occupant Detection System Sensor Pad to fifteen (15) years with unlimited mileage, starting from the date the vehicle was first put into service.

Warranty Extension on the Occupant Detection System Sensor Pad to fifteen (15) years with unlimited mileage, starting from the date the vehicle was first put into service.

on the Occupant Detection System Sensor Pad to fifteen (15) years with unlimited mileage, starting from the date the vehicle was first put into service.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

procedure to replace the front passenger Occupant Detection System (ODS) Sensor Pad on 2011-2015MY Sorento (XMa) vehicles produced from September 24, 2009 through December 11, 2014.

provides the procedure on how to inspect, clean and seal or, if necessary, replace the rear wheel speed sensor (WSS) housing covers on certain 2011-2015MY 2WD Sorento (XMa) vehicles, produced from October 24, 2009 through April 30, 2014, originally retailed and/or currently registered in the coastal states of Alabama, Florida, Georgia, Hawaii, Louisiana, Mississippi, North Carolina, South Carolina and Texas. If the rear wheel hub comes into contact with a significant amount of seawater, the water can enter the rear wheel speed sensor housing covers and may interrupt the rear wheel speed sensor signal and illuminate the Anti-Lock Braking System (?ABS?) and/or Electronic Stability Control (?ESC?) warning lights in the instrument cluster.

once fully attached, are utilized in various Kia models and are strictly intended for ?one time use.? Some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.? It is critical for technicians to be aware that ALL such locking fasteners, regardless of type, are for ?one time use? only.

strictly intended for ?one time use?. Though not limited to the following, some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.?

complaint related to an inoperative parking light confirmation flash, and/or audible answer back when locking the vehicle with the RKE/SMK fob, ensure each door lock position switch (viewable in BCM > Current Data) is displaying the appropriate status and the pad-lid switch (hood switch depressor) is in place on the hood.

connector on some 2011 - 2013MY Sorento (XMa) vehicles, produced from October 24, 2009 through January 31, 2013, which may experience an inoperable low beam bulb due to poor terminal contact at the low beam bulb connector.

connector on some 2011 - 2013MY Sorento (XMa) vehicles, produced from October 24, 2009 through January 31, 2013, which may experience an inoperable low beam bulb due to poor terminal contact at the low beam bulb connector. This condition on the affected headlamp does not affect the other low beam. In addition, the high beams continue to function at all times.

August to provide you with an update regarding news reports regarding non-collision fires in Kia vehicles and NHTSA?s announcement of the opening of a Defect Petition for fire cases involving the 2011-14 Sorento and Optima vehicles. Since that time, we have been working cooperatively with NHTSA to analyze the safety performance of these and all Kia vehicles and added additional resources to quickly and effectively address any incidents. Recently, a non-profit consumer advocacy group called the Center for Automotive Safety (CAS) has asked for a recall of Kia vehicles for fire risk and members of the Senate Commerce Committee have asked Kia for additional information related to non-collision fires in Kia vehicles. These actions have generated additional media reports so we are providing you with additional information to assist you and your teams in addressing customer concerns.

ACTUATOR OF SOME ALL-WHEEL DRIVE (AWD) EQUIPPED 2011~2016MY SPORTAGE (SL) VEHICLES, PRODUCED FROM MAY 6, 2010 THROUGH FEBRUARY 19, 2013 AND SOME AWD EQUIPPED 2011~2015MY SORENTO (XMA) VEHICLES, PRODUCED FROM OCTOBER 24, 2009 THROUGH DECEMBER 11, 2014, WHICH MAY EXHIBIT AN INOPERATIVE AWD SYSTEM WITH THE MALFUNCTION INDICATOR LAMP (MIL) ON AND DTCS P1820/1821/1822/1823/1824 (ACTIVE OR IN HISTORY). TO CORRECT THIS CONCERN, REPLACE THE AFFECTED HYDRAULIC ACTUATOR BY REFERRING TO THE APPLICABLE SERVICE PROCEDURE ON KGIS.

SPORTAGE VEHICLES, WILL EXHIBIT AN INOPERATIVE AWD SYSTEM WITH MALFUNCTION INDICATOR LAMP. *LJ

EXPERIENCING ILLUMINATION MALFUNCTION INDICATOR LAMP (MIL) AND CONCERNS ABOUT DRIVABILITY. MODELS 2011-2013 SORENTO. *PE

THE ETC ACTUATOR MAY NEED TO BE REPLACED. *JS

identify and record the head unit software level on various head unit platforms and generations.

(ELE091) (Rev 1) - This bulletin provides the procedure on how to identify and record the head unit software level on various head unit platforms and generations. This procedure will now be required when ordering head units through the Direct Exchange Program (see Parts Bulletin 91-961-0005).

ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.

COMPATIBILITY ISSUES BETWEEN NAVIGATION HEAD UNITS AND SD CARDS WHEN REPLACING HEAD UNITS FOR MULTIMEDIA ISSUES. IF AFTER REPLACING A NAVIGATION HEAD UNIT THE ORIGINAL SD CARD DOES NOT OPERATE CORRECTLY, FOLLOW THE STEPS BELOW TO DIAGNOSE THE ISSUE:

BLUETOOTH CONCERNS WHEN USING AN IPHONE WITH IOS 8.X (IOS 8, 8.0.1, 8.0.2, 8.1, 8.1.2, 8.1.3, ETC.) WHILE PAIRED TO A HEAD UNIT.

ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.

SYSTEM SOFTWARE OF SOME 2013MY SOUL (AM), OPTIMA (TF/QF), SORENTO (XMA) AND FORTE (TD) VEHICLES, TO IMPROVE BLUETOOTH CONNECTIVITY.

(XM), OPTIMA (TF/QF), RIO (UB) AND SPORTAGE (SL) VEHICLES TO IMPROVE BLUETOOTH CONNECTIVITY.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the replacement of the clock spring assembly on 2011MY - 2015MY Sorento (XMa) vehicles. Kia is extending the warranty coverage for the drivers front airbag clock spring assembly on the 2011-2015 MY Sorento vehicles, manufactured from 10/24/2009 through 12/17/2014, to fifteen (15) years with unlimited mileage, starting from the date of first service. This warranty extension addresses failures of the drivers front airbag clock spring, as well as the diagnosis of any concerns related to the airbag warning light.

the customer has paid for repairs to the airbag clock spring assembly.

2011-2015 My Sorento Airbag Clock Spring Assembly.

EXTENSION Q & A

CREAKING NOISE HEARD FROM THE FRONT OF THE VEHICLE WHEN TURNING THE WHEEL QUICKLY AT SLOW SPEEDS, ON SOME 2011 - 2013MY SORENTO (XMA), PRODUCED PRIOR TO AUGUST 28, 2012. THIS CONCERN MAY BE CAUSED BY CORROSION OF THE FRONT STRUT BEARING DUE TO WATER OR DEBRIS ENTRY AND IS MORE COMMONLY FOUND IN REGIONS WITH HIGHER SNOWFALL AND ROAD SALT USAGE.

REPLACING THE FRONT STRUT BEARINGS ON SOME 2011- 2013MY SORENTO (XMA) VEHICLES, PRODUCED FROM OCTOBER 26, 2009 THROUGH JANUARY 21, 2013, WHICH MAY EXHIBIT A CREAKING NOISE EMANATING FROM THE FRONT OF THE VEHICLE WHEN TURNING THE WHEEL QUICKLY, AT SLOW SPEEDS. TO CORRECT THIS CONDITION, REPLACE THE FRONT STRUT BEARING BY FOLLOWING THE PROCEDURE OUTLINED IN THIS BULLETIN.

2011MY 2015MY SORENTO (XMA) VEHICLES. IF THE AIRBAG WARNING LIGHT IS ON WITH ANY OF THE DTCS LISTED BELOW, FOLLOW THE PROCEDURE OUTLINED TO RESOLVE THE ISSUE.

launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.

launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.

a new Special Service Tool (SST) (A) developed to prevent the hood release lever pivot point (B) from being damaged when removing the hood release lever. Follow the instructions included in this bulletin to properly remove the hood release lever using the new SST.

DEBRIS ACCUMULATION ON THE WINDSHIELD WASHER PUMP INLET FILTER. OVER TIME, SOME KIA VEHICLES MAY EXHIBIT A LIMITED APPLICATION OF WINDSHIELD WASHER FLUID WHEN THE WASHER FUNCTION IS USED. LIMITED APPLICATION OF WINDSHIELD WASHER FLUID CAN BE CAUSED BY FOREIGN DEBRIS ON THE WASHER PUMP INLET FILTER. TO CORRECT THIS CONDITION, REPLACE THE WASHER PUMP INLET FILTER AND PERFORM THE WINDSHIELD WASHER RESERVOIR FLUSHING PROCEDURE OUTLINED IN THIS TSB.

ASSEMBLY WITH TORN DUST SEALS.

FROM THE RIGHT AND/OR LEFT SIDE OF THE DASH WHILE DRIVING AT HIGHWAY SPEEDS. THIS CONCERN MAY BE CAUSED BY THE FENDER TRIM RUBBING AGAINST THE FENDER LINER.

you last August and again last October to provide you with updates regarding news reports about non-collision fires in Kia vehicles and the status of Kia?s cooperative work with NHTSA.

reports regarding thermal incidents in Kia vehicles or NHTSA?s announcement of the opening of a Defect Petition for fire cases involving the 2011-14 Sorentos and Optimas, and I want to update you on KMA?s response to this issue. All automobiles contain combustible materials and a vehicle fire may be a result of any number of complex factors which must be carefully evaluated by trained technicians to, if possible, determine its cause and, ultimately, determine if a defect trend exists. At Kia, customer safety is paramount and although both KMA and NHTSA have independently concluded that no defect trends exist, KMA has significantly increased its committed resources to ensure that all thermal incidents are fully evaluated.

KIA IS REQUESTING THE COMPLETION OF THIS SERVICE ACTION ON ALL AFFECTED 2013MY SORENTO VEHICLES PRIOR TO DELIVERY. BEFORE CONDUCTING THE PROCEDURE, VERIFY THAT THE VEHICLE IS INCLUDED IN THE LIST OF THE AFFECTED VINS.

UPGRADING THE KIA UVO (YOUR VOICE) SYSTEM. KIA UVO OWNERS HAVE THE OPTION TO DOWNLOAD AVAILABLE UPGRADES DIRECTLY FROM THE KIA.COM WEBSITE AND CAN PERFORM THE UPGRADE THEMSELVES OR HAVE THE DEALER PERFORM THE UPGRADE IN WHICH CASE ADDITIONAL LABOR CHARGES MAY APPLY. FOR CUSTOMERS WHO PERFORM THEIR OWN UPGRADE, KIA PROVIDES THE CUSTOMER WITH SOFTWARE AND UPGRADE INSTRUCTIONS. IF THE CUSTOMER OPTS TO HAVE THE DEALER PERFORM THE UPGRADE, THE UPGRADE PROCEDURE IS OUTLINED IN THIS BULLETIN.

SORENTO (XMA) VEHICLES, PRODUCED FROM OCTOBER 26, 2009 TO NOVEMBER 5, 2012, WHICH MAY EXHIBIT A CONCERN RELATED TO THE SECOND ROW SEATS BEING INOPERATIVE OR DIFFICULT TO RELEASE. IT IS IMPORTANT TO NOTE THAT SOME AMOUNT OF EFFORT IS REQUIRED TO FOLD THE 2ND ROW SEATS. TO CORRECT THIS CONDITION, FOLLOW THE SERVICE PROCEDURE OUTLINED IN THIS TSB.

SORENTO (XMA) VEHICLES, PRODUCED FROM OCTOBER 26, 2009 TO NOVEMBER 5, 2012, WHICH MAY EXHIBIT A CONCERN RELATED TO THE SECOND ROW SEATS BEING INOPERATIVE OR DIFFICULT TO RELEASE. IT IS IMPORTANT TO NOTE THAT SOME AMOUNT OF EFFORT IS REQUIRED TO FOLD THE 2ND ROW SEATS. TO CORRECT THIS CONDITION, FOLLOW THE SERVICE PROCEDURE OUTLINED IN THIS TSB.

CAMERA OF SOME KIA VEHICLES (SEE TABLE ON PG. 6 FOR SPECIFIC MODELS AND PRODUCTION DATES) WHICH MAY EXHIBIT INADEQUATE IMAGE QUALITY FROM THE REAR VIEW CAMERA. DIAGNOSE THE CONCERNS USING THE INFORMATION IN THIS BULLETIN AND, IF NECESSARY, REPLACE THE REAR VIEW CAMERA WITH AN IMPROVED PART BY FOLLOWING THE APPLICABLE SERVICE PROCEDURE ON KGIS.

incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.

function using the GDS.

SEE WARRANTY BULLETIN 2017-09 (SC147).

MAY BE CAUSED BY SPIDER WEBS IN AND AROUND THE EVAPORATIVE EMISSIONS VENT LINES CREATING THE SET DTC. TO REPAIR THIS CONDITION, INSPECT THE AIR FILTER ASSEMBLY (LOCATED ON THE CCV) AND THE EVAPORATIVE EMISSIONS VENT LINES FOR SPIDER WEBS OR DEBRIS BEFORE REPLACING ANY COMPONENTS. THE SPIDER WEBS NEEDS TO BE CLEARED FROM THE LINES WITH A PIPE CLEANER, WIRE OR REPLACEMENT OF THE RESTRICTED COMPONENT (BLOWING COMPRESSED AIR THROUGH THE LINES IS OFTEN INEFFECTIVE).