2017 Kia Optima TSBs

(CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)

notification advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) for certain 2016-2020 MY Optima vehicles equipped with 2.4L Gas Direct Injection (GDI) engines to ensure compliance with emissions regulations.

(CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

notification advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) for certain 2016-2020 MY Optima vehicles equipped with 2.4L Gas Direct Injection (GDI) engines to ensure compliance with emissions regulations.

notification advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) for certain 2016-2020 MY Optima vehicles equipped with 2.4L Gas Direct Injection (GDI) engines to ensure compliance with emissions regulations.

(SC340) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to upgrade the Electronic Control Module ECM system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.

(SC340) - This bulletin provides information to upgrade the Electronic Control Module ECM system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.

bulletin has been revised to include additional information. New / revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to upgrade the Electronic Control Module ECM system software for certain 2016-2022MY vehicles equipped with 2.4L Theta II engines listed in the table below. Kia has become aware that certain 2016-2022MY vehicles equipped with 2.4L Theta II engines may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.

to the dealer Parts and Service managers advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations in certain 2017-2022 MY Sportage vehicles manufactured from December 10, 2015, through December 7, 2021, certain 2016-2020 MY Optima vehicles manufactured from August 28, 2015, through June 23, 2020, and certain 2016-2020 MY Sorento vehicles manufactured from October 27, 2014, through November 4, 2020, equipped with 2.4L Theta GDI engines.

principals advising that Kia is conducting a Voluntary Emissions Service Campaign to improve the emissions software logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations in certain 2017-2022 MY Sportage vehicles manufactured from December 10, 2015, through December 7, 2021, certain 2016-2020 MY Optima vehicles manufactured from August 28, 2015, through June 23, 2020, and certain 2016-2020 MY Sorento vehicles manufactured from October 27, 2014, through November 4, 2020, equipped with 2.4L Theta GDI engines.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

bulletin provides the procedure to relocate the Heating, Ventilation, and Air Conditioning (HVAC) blower motor 40-ampere fuse on some 2016-2020MY Optima (JFa) vehicles produced from August 28, 2015 through June 23, 2020 which may experience an inoperative blower motor due to a blown multi-fuse at position #3. The HVAC system provides cooling and heating to help maintain a comfortable environment inside the vehicle cabin. The blower motor provides primary airflow for the HVAC system. Extended use of the HVAC system at high fan speeds may cause damage to the multi-fuse terminals for the HVAC blower motor circuit, which can cause the blower motor to become inoperative, resulting in reduced heat and air conditioning.

This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement"; equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to improve the logic of the Battery Management System (BMS), Oil Pump Control Unit (OPU) and Motor Control Unit (MCU) on some 2017-2019MY Optima (JF P/HEV) vehicles, produced from August 25, 2016 through September 13, 2018 (refer to page 8) in order to improve the BMS diagnosis logic, OPU judgment logic for DTC P1B77 (High Voltage Battery Pre-Charging fault) and MCU communication logic.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information associated with the 'Warranty Extension Program' (WTY028) to inspect and, if necessary, replace the fuel pump filter assembly on 2016-2020MY Optima (JFa) vehicles produced from August 28, 2015 through June 23, 2020, for repairs that may be necessary to address a low-pressure fuel pump failure to be covered for 15 years / 150,000 miles, whichever comes first starting from the date the vehicle was first put into service. The affected vehicles may exhibit an intermittent reduction in engine power, contain an active or stored DTC P1233 and/or exhibit a 'No Start' condition due to a cracked fuel pump filter housing.

the 'Warranty Extension Program' (WTY028) to inspect and, if necessary, replace the fuel pump filter assembly on 2016-2020MY Optima (JFa) vehicles produced from August 28, 2015 through June 23, 2020, for repairs that may be necessary to address a low-pressure fuel pump failure to be covered for 15 years / 150,000 miles, whichever comes first starting from the date the vehicle was first put into service. The affected vehicles may exhibit an intermittent reduction in engine power, contain an active or stored DTC P1233 and/or exhibit a 'No Start' condition due to a cracked fuel pump filter housing.

test procedure of the Bearing Clearance Tester (BCT) Special Service Tool (SST). The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.

provides the procedure to update the emissions-related logic of the Engine Control Unit (ECU) on some 2016-2020MY Optima (JFa) ULEV vehicles, equipped with 2.0L T-GDI Theta engines, produced from April 21, 2015 through May 22, 2020, in order to improve fuel quantity learning to decrease the deterioration of the rear Oxygen Sensor.

conducting a Voluntary Emissions Service Campaign to update the software programming on your vehicle's Engine Control Module (SC205).

dealer Parts and Service Managers that Kia is conducting a Voluntary Emissions Service Campaign on 2016-2020 MY Kia Optima vehicles equipped with the 2.0L Turbo-GDI engine to update the emission related logic of the Engine Control Module "ECM" with an improved version to ensure compliance with emissions regulations.

that Kia is conducting a Voluntary Emissions Service Campaign on 2016-2020 MY Kia Optima vehicles equipped with the 2.0L Turbo-GDI engine to update the emission related logic of the Engine Control Module "ECM" with an improved version to ensure compliance with emissions regulations.

to address a no-start or hard start with poor running condition after engine replacement under PI1802Y/Z or PI1803Y/Z. Some replacement long blocks may come with pre-installed fuel rail, injectors, and injector wiring harness. If the condition is present, it is possible that the injector harness was not installed correctly. The connections may be swapped from cylinder No. 1 and cylinder No. 4, and from cylinder No. 2 and cylinder No. 3.

information regarding the diagnosis of Motor Driven Power Steering (MDPS), also known as Electronic Power Steering (EPS), and parts replacement associated with the Warranty Extension Program (WTY023) on 2016-2017MY Optima (JF/JFa), 2017MY Optima HEV/PHEV (JF P/HEV), 2016-2017MY Sorento (UMa) vehicles produced in the ranges listed below. The affected vehicles may exhibit the MDPS (also known as EPS) warning lamp ON. The warranty coverage for repairs related to the MDPS unit due to illumination of the MDPS warning lamp has been extended to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

Kia is extending the New Vehicle Limited Warranty coverage for repairs related to the Motor Driven Power Steering (MDPS) unit, also known as Electronic Power Steering (EPS) unit, due to illumination of the EPS warning light for all 2016-2017 MY Optima vehicles from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

asked questions regarding the warranty extension (WTY023). Kia America, Inc., is extending the New Vehicle Limited Warranty coverage for the Motor Driven Power Steering (MDPS) unit, also known as Electronic Power Steering (EPS) unit, from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

Service Managers of the warranty extension program for WTY023. Kia America, Inc., is extending the New Vehicle Limited Warranty coverage for the Motor Driven Power Steering (MDPS) unit, also known as Electronic Power Steering (EPS) unit, from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

Kia America, Inc., is extending the New Vehicle Limited Warranty coverage for the Motor Driven Power Steering (MDPS) unit, also known as Electronic Power Steering (EPS) unit, from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

Service Managers of the warranty extension program for WTY023. Kia America, Inc., is extending the New Vehicle Limited Warranty coverage for the Motor Driven Power Steering (MDPS) unit, also known as Electronic Power Steering (EPS) unit, from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. The power steering uses a motor to assist in steering the vehicle. If the engine is off or if the power steering system becomes inoperative, the vehicle may be steered, but it will require increased steering effort by the driver. This warranty extension is to address specific concerns with the functionality of the MDPS unit.

Kia America, Inc., is extending the New Vehicle Limited Warranty coverage for the Motor Driven Power Steering (MDPS) unit, also known as Electronic Power Steering (EPS) unit, from 5 years/60,000 miles to 15 years/150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. The power steering uses a motor to assist in steering the vehicle. If the engine is off or if the power steering system becomes inoperative, the vehicle may be steered, but it will require increased steering effort by the driver. This warranty extension is to address specific concerns with the functionality of the MDPS unit.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

provides the procedure to update the software logic of the Dual Clutch Transmission (DCT) system on some 2016-2020MY Optima (JFa) vehicles produced from August 28, 2015 through June 1, 2020, equipped with Gamma 1.6L T-GDI engine and 7-speed DCT, which might exhibit clutch judder when accelerating from a stop.

provides information regarding the availability of partial repair (depending on faulty components) of the Dual Pinion Motor Driven Power Steering (DP-MDPS) system on some 2016-2021MY~ Kia vehicles (refer to the table below) in order to enhance customer satisfaction by promoting a cost-effective repair/replacement of a faulty related part, instead of replacement of the complete DP-MDPS assembly.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled Knock Sensor Detection System - ECU Logic Improvement equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

revised to include additional information. - This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement".

revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement".

been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

This Pitstop provides information regarding the updated spark plug for vehicles listed below, equipped with 2.0T Theta-II engines, which may not yet be available in the Electronic Parts Catalog (EPC). If not available, the updated spark plug must be ordered manually. This updated spark plug has been improved with the thread shoulder lengthened to enhance protection of the insulator from combustion heat.

- SUPERSEDED BY PI1802YZ/1803YZ.

to improve the logic of the Battery Management System (BMS), Oil Pump Control Unit (OPU) and Motor Control Unit (MCU) on some 2017-2019MY Optima (JF P/HEV) vehicles, produced from August 25, 2016 through September 13, 2018 (refer to page 8) in order to improve the BMS diagnosis logic, OPU judgment logic for DTC P1B77 (High Voltage Battery Pre-Charging fault) and MCU communication logic.

to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

BY PI1802Y/Z.

revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled Knock Sensor Detection System - ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

to include additional information.This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC), P1326.

is conducting an important Product Improvement Campaign to perform a software update on some 2014 MY Optima vehicles equipped with 2.4L Gasoline Direct Injection ("GDI") engines, and all 2015-2018 MY Optima vehicles equipped with 2.4L GDI and 2.0L Turbocharged GDI ("T-GDI") engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").

bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled '"Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

the lower engine service cover on 2016-2020MY Optima 2.4L and 2.0L equipped vehicles. The lower engine service cover is secured by seven (7) retaining bolts. Installation of the two (2) long bolts in the incorrect location may cause puncture or damage to the oil pan in the event that the vehicle is bottomed out while driving. If the oil pan is damaged or punctured, the engine oil may leak, possibly causing engine damage. This

information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage. The KSDS detects vibrations indicating the onset of excessive connecting rod bearing wear. It is designed to alert the driver at an early stage of bearing wear before the occurrence of severe engine damage, including engine failure. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Limp Home Mode. This will reduce further damage to the engine and ensure that the vehicle occupants are not exposed to the risk of a more severe engine failure. At that time, Diagnostic Trouble Code (DTC) P1326, specific to the KSDS, will be recorded in the ECU. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed. Also, engine RPMs will be limited to approximately 1800-2000 RPM.

is conducting an important Product Improvement Campaign to perform a software update on some 2014 MY Optima vehicles equipped with 2.4L Gasoline Direct Injection ("GDI") engines, and all 2015-2018 MY Optima vehicles equipped with 2.4L GDI and 2.0L Turbocharged GDI ("T-GDI") engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").

This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on the Kia models listed on the chart below with a column mounted C-MDPS unit.

related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.

related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.

Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

to include additional information This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326..

to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 5, 12/20/2018) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.

revised to include additional information.This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

This bulletin provides information relating to all Kia vehicles equipped with Gasoline Direct Injection (GDI) engines. In these engines highly pressurized gasoline is injected via a common fuel rail and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional Multi-Point Fuel Injection (MPI) engine, the gasoline is injected into the intake port of each cylinder at a relatively low pressure. Due to high fuel pressure in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specifications for the GDI fuel system components.

This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor and/or Electronic Control Unit (ECU) on the listed Kia models with a column mounted C-MDPS unit.

is conducting an important Product Improvement Campaign to perform a software update on all 2016-2018 MY Optima vehicles equipped with 2.4L Gasoline Direct Injection (?GDI?) and 2.0L Turbocharged GDI (?T-GDI?) engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (?ECU?).

This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage

Driven Power Steering (MDPS) Motor and/or Electronic Control Unit (ECU) on the listed Kia models with a column mounted C-MDPS unit. Follow the procedure outlined in this bulletin.

update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

This bulletin provides information regarding the inspection and/or replacement of the E-CVVT cover or O-ring and replacement of the motor plug on some 2016-2017MY Optima (JF, JFa), 2016-2017MY Sorento (UMa), and 2017MY Sportage (QL) vehicles, equipped with 2.4L GDI or 2.0T-GDI, which may exhibit a malfunction indicator light (MIL) ON with DTC P001000 and/or oil leakage in the E-CVVT motor plug of applicable vehicles.

considered serviceable, and should be thoroughly cleaned and transferred to the new engine.

This bulletin provides information regarding the inspection and/or replacement of the E-CVVT cover or O-ring and replacement of the motor plug on some 2016-2017MY Optima (JF, JFa), 2016-2017MY Sorento (UMa), and 2017MY Sportage (QL) vehicles, equipped with 2.4L GDI or 2.0T-GDI, which may exhibit a malfunction indicator light (MIL) ON with DTC P001000 and/or oil leakage in the E-CVVT motor plug of applicable vehicles.

replace the air intake hose and/or improve the logic of the Electronic Control Unit (ECU) on some 2016-2017MY Optima (JFa), produced from September 4, 2015 through April 14, 2017, and some 2016-2017MY Sorento (UMa) vehicles, produced from November 19, 2014 through May 1, 2017, equipped with a 2.0T engine, which may exhibit an impaired air intake hose.

information regarding the inspection and/or replacement of the E-CVVT cover or O-ring and replacement of the motor plug on some 2016-2017MY Optima (JF, JFa), 2016-2017MY Sorento (UMa), and 2017MY Sportage (QL) vehicles, equipped with 2.4L GDI or 2.0T-GDI, which may exhibit a malfunction indicator light (MIL) ON with DTC P001000 and/or oil leakage in the E-CVVT motor plug of applicable vehicles.

regarding the inspection and/or replacement of the E-CVVT cover or O-ring and replacement of the motor plug on some 2016-2017MY Optima (JF, JFa), 2016-2017MY Sorento (UMa), and 2017MY Sportage (QL) vehicles, equipped with 2.4L GDI or 2.0T-GDI, which may exhibit a malfunction indicator light (MIL) ON with DTC P001000 and/or oil leakage in the E-CVVT motor plug of applicable vehicles.

related to extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.

extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting. To facilitate collection of this data at the dealer level, KDS screenshots will allow the capture of relevant parameters.

7-speed Dual Clutch Transmission (DCT), except the 2017MY~ Niro (DE) with a 1.6L Atkinson engine comes equipped with a 6-speed Dual Clutch Transmission (DCT). This automatic transmission is unlike the conventional automatic transmission found in the complete line up of Kia vehicles. The new DCT improves fuel efficiency and can also provide a sportier feel. Certain aspects of this technology may lead to customer concerns if they are unfamiliar with it. To help maximize owner satisfaction on this new technology, Kia would like all dealership sales and service personnel to be familiar with the characteristics of this new transmission.

SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2011-2015MY Optima (TF), 2012-2015MY Optima (QF) and 2016-2020MY Optima (JF, JFa) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.

This bulletin provided the procedure to increase the torque on the voltage regulator screws on some 2017MY Sorento (UMa), produced from October 3, 2016 to January 24, 2017, and 2017MY Optima (JFa) vehicles, produced from October 3, 2016 to January 26, 2017, which may experience low battery voltage or a no-start condition.

COMPATIBILITY (CS2310) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 7. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2011-2015MY Optima (TF), 2012-2015MY Optima (QF) and 2016-2020MY Optima (JF, JFa) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

COMPATIBILITY (CS2310) - This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 6. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2011-2015MY Optima (TF), 2012-2015MY Optima (QF) and 2016-2020MY Optima (JF, JFa) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2011-2015MY Optima (TF), 2012-2015MY Optima (QF) and 2016-2020MY Optima (JF, JFa) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2011-2015MY Optima (TF), 2012-2015MY Optima (QF) and 2016-2020MY Optima (JF, JFa) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

alignment on 2014MY and later vehicles that may exhibit a warning light ON related to radar sensor alignment errors in the Forward Collision-Avoidance Assist (FCA)/Smart Cruise Control (SCC) system.

below during PDI, make sure to use the procedure outlined below to raise the wiper arms to the fully vertical position in order to avoid damaging the paint on the rear edge of the hood. It is important to note that the wipers on these vehicles are recessed under the hood to provide better appearance and reduced wind noise characteristics. This procedure applies to both key start and SMK type ignition systems.

The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.

This bulletin provides the procedure to increase the torque on the voltage regulator screws on some 2017MY Sorento (UMa), produced from October 3, 2016 to January 24, 2017, and 2017MY Optima (JFa) vehicles, produced from October 3, 2016 to January 26, 2017, which may experience low battery voltage or a no-start condition.

regarding a running change to the High Voltage (HV) Battery and Battery Management System (BMS) control unit assemblies on 2017MY Optima Hybrid (JF HEV only, does not apply to PHEV) vehicles.

provides the procedure to inspect the Hybrid Starter Generator (HSG) pulley nut and, if necessary, replace the HSG assembly on certain Optima JF HEV/PHEV vehicles with a production range from May 31, 2016 to November 22, 2016, which may exhibit a loose pulley nut.

torque on the voltage regulator screws on some 2017MY Sorento (UMa), produced from October 3, 2016 to January 24, 2017, and 2017MY Optima (JFa) vehicles, produced from October 3, 2016 to January 26, 2017, which may experience low battery voltage or a no-start condition. Follow the procedure outlined in this bulletin to increase the two (2) screws? torque on the voltage regulator. Before conducting the procedure, verify that the vehicle is included in the list of affected VINs.

SOME VEHICLES EQUIPPED WITH BLIND SPOT DETECTION (BSD), WHICH MAY EXHIBIT A CHECK BSD SYSTEM MESSAGE WITH DTCS: C270254 AND C270354: C270254: CONTROL MODULE MASTER MISSING CALIBRATION / C270354: CONTROL MODULE SLAVE MISSING CALIBRATION

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace the inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP), and some 2016-2017MY Optima (JF) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the concerns listed below. These concerns may be due to the inhibitor switch not allowing the correct gear position signal to be sent to various control units.

include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace the inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP), and some 2016-2017MY Optima (JF) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the concerns listed below. These concerns may be due to the inhibitor switch not allowing the correct gear position signal to be sent to various control units.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace the inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP), and some 2016-2017MY Optima (JF) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the concerns listed below. These concerns may be due to the inhibitor switch not allowing the correct gear position signal to be sent to various control units.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace Dual Clutch Assembly and upgrade the TCU on some 2016-2020MY Kia vehicles listed in the table below, equipped with the 7 Speed Dual Clutch Transmission (DCT), which might exhibit clutch judder when accelerating from a stop.

window regulator drum gear on some 2016-2017MY Optima (JFa) vehicles, produced from September 01, 2015 through July 31, 2016, which may exhibit an inoperative window regulator due to a drum gear separating and/or breaking.

the procedure to replace Dual Clutch Assembly and upgrade the TCU on some 2016-2020MY Kia vehicles listed on the table below, equipped with the 7 Speed Dual Clutch Transmission (DCT), which might exhibit clutch judder when accelerating from a stop. If the vehicle body vibrates without the steering wheel shuddering when performing creep driving test (driving the vehicle up to 3mph), the vehicle is exhibiting clutch judder. The creep test can be conducted by driving at a speed slower than 5 mph after releasing the brake.

This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.

This bulletin provides the procedure to replace the inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP), and some 2016-2017MY Optima (JF) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the concerns listed in this bulletin. These concerns may be due to the inhibitor switch not allowing the correct gear position signal to be sent to various control units.

(Electronic Control Unit) on some 2016-2017MY Optima (JFa) 1.6T GDI ULEV DCT vehicles, produced from September 28, 2015 through September 03, 2016, which exhibit a MIL (Malfunction Indicator Lamp) illuminated with DTC P0128, even though there are no system faults.

Unit (TCU) on 2017-2018MY Soul (PS) and Forte (YDm) and 2016-2018MY Optima (JFa) vehicles equipped with 1.6T GDI that have one of the following three components replaced: Dual Clutch Transmission (DCT) assembly; Transmission Control Unit (TCU), and Double Clutch Set.The friction material of the double clutch set has been changed and a TCU logic optimization must be performed in order to prevent initial shift shock.

- This bulletin provides the procedure to replace the inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP), and some 2016-2017MY Optima (JF) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the following concerns: ? Malfunction Indicator Lamp (MIL) ON with DTC P0705 - Transmission Range Sensor (TRS) Circuit Malfunction (active or history) ? CAN-related DTCs (For both Hybrids: CAN DTC C2243); ? Intermittent no crank/no start ? Erratic or harsh shifting; ? EPB and Hold lights illuminated intermittently; ? ?Key OFF? indicated after placing the selector lever into the ?P? position and depressing the Start/Stop button.Note: When this condition occurs, the ?P? position is not indicated on the instrument cluster.

This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.

inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the concerns listed below. These concerns may be due to the inhibitor switch not allowing the correct gear position signal to be sent to various control units.

inhibitor switch on some 2017MY Optima (JFa) and Sorento (UMa), produced from August 29, 2016 through June 15, 2017, and some 2017MY Optima Hybrid (HEV) and Optima Plug-in Hybrid (PHEV) vehicles, produced from June 27, 2016 through April 4, 2017, and equipped with a front wheel drive 6-speed transmission, which may experience the concerns listed below. These concerns may be due to the inhibitor switch not allowing the correct gear position signal to be sent to various control units.

JF-HEV, JF-PHEV) vehicles, the accelerator pedal features a small detent with a spring to provide increased resistance to help avoid unnecessary fuel consumption when applying full throttle. When the driver depresses the pedal beyond the resistance where the detent is felt (above 85% WOT), the pedal will easily reach WOT and kickdown shift will occur accordingly. For additional information, refer to the individual vehicle?s Owner?s Manual under section ?Driving Your Vehicle? ? Automatic Transmission (Drive).

containing the most frequently asked questions regarding the Voluntary Emissions Service Campaign SC340.

the most frequently asked questions regarding the Voluntary Emissions Service Campaign (SC205).

Vehicle Limited Warranty coverage for repairs related to low-pressure fuel pump failure in 2016-2020 MY Optima vehicles manufactured at a Kia assembly plant in the U.S. from 5 years / 60,000 miles to 15 years / 150,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

Service Managers that Kia is extending the New Vehicle Limited Warranty coverage for repairs related to low-pressure fuel pump failure for 2016-2020 MY Optima vehicles manufactured at a Kia assembly plant in the U.S. from 5 years/60,000 miles to 15 years/ 150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. This warranty extension is to address certain concerns related to the potential failure of the low-pressure fuel pump.

extending the New Vehicle Limited Warranty coverage for repairs related to low-pressure fuel pump failure for 2016-2020 MY Optima vehicles manufactured at a Kia assembly plant in the U.S. from 5 years/60,000 miles to 15 years/ 150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. This warranty extension is to address certain concerns related to the potential failure of the low-pressure fuel pump.

provides the procedure to perform an evaporative leak test and replace the fuel tank air filter, and, if necessary, the Natural Vacuum Leak Detector (NVLD) on some Optima (JF HEV) vehicles, produced from June 27, 2016 through January 7, 2019, which may experience an evaporative leak concern with DTC P0456.

models such as K900 (KH), Sedona (YP), Sorento (UMa), Optima (JFa), Sportage (QL), and 17MY Forte (YD, YDm), etc., equipped with a sunroof, a ventilation logic has been applied in order to prevent exhaust gases flowing into the vehicle due to the pressure difference (inside vs outside) that is generated when driving with the sunroof open. This logic allows the system to automatically switch from RECIRCULATION to FRESH mode when the sunroof is open.

New/revised sections of this bulletin are indicated by a black bar in the margin area. When servicing windshield wipers on the below listed vehicles, including during PDI, ensure to raise the wiper arms to a vertical position to avoid damaging the paint on the rear edge of the hood.

certain Forte, Rio and Optima vehicles, which may exhibit a difficult-to-close/latch concern with the trunk lid.

inoperative mirror glass on the outside door mirrors for 2016-2019MY Optima (JFa) and Sorento (UMa) vehicles.

2016MY~ Optima (JFa/JF), and 2018MY~ Stinger (CK) vehicles during PDI, make sure to use the procedure outlined below to raise the wiper arms to the fully vertical position in order to avoid damaging the paint on the rear edge of the hood. It is important to note that the wipers on these vehicles are recessed under the hood to provide better appearance and reduced wind noise characteristics.

the trunk not opening as designed when using transmitter key fob or Smart Trunk feature. This may be caused by improper assembly of the trunk torsion bar (A) and trunk lid hinge. Follow the procedure in this publication to correct this concern.

of the UVO eServices buttons located on the rear view mirror in some 2016-2017MY K900 (KH), and 2017MY Optima Plug-in Hybrid (JF PHEV) and 2017MY Soul EV (PS EV) vehicles.

COVER AND CHECK FOR POSSIBLE OIL INTRUSION (A). THE ECVVT SYSTEM UTILIZES TWO SEALS TO PREVENT INTRUSION OF OIL AND/OR DUST A SEAL ON THE COVER (A) AND A SEAL THAT IS RECESSED IN THE ECVVT. IF OIL IS FOUND INSIDE THE COVER; THE COVER, THE OIL SEAL WITHIN THE E-CVVT ASSEMBLY AND THE E-CVVT ASSEMBLY SHOULD BE REPLACED. FOLLOW THE INSTRUCTIONS LISTED IN THE SERVICE INFORMATION, AND IN THE VIDEO LINK BELOW, TO PROPERLY INSTALL THE OIL SEAL TO THE CORRECT DEPTH AND ALIGN THE COVER.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the repair procedure for the Integrated Brake Actuation Unit (iBAU) system on some 2014-2019MY EV/Hybrid/Plug-In Hybrid vehicles listed (see table), which may exhibit a "honking" (Hissing) noise due to air remaining in the brake fluid system.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

This bulletin provides the procedure to improve the logic of the Autonomous Emergency Brake (AEB) control unit on some 2016-2017MY Optima (JFa), and 2017MY Sorento (UMa), Forte (YDm), and Sedona (YP) vehicles, which may experience unexpected AEB activation in certain circumstances.

to replace the outside rear combination lamp harness on some 2016-2017MY Optima (JFa) vehicles, produced from September 25, 2016 through March 16, 2017, which may exhibit an intermittent inoperative brake light with the possibility of a ?Check brake light? warning on the instrument cluster display.

with Autonomous Emergency Braking (AEB). Some customers may have interest and/or questions regarding this new technology, including what type of feedback they can expect from this system. The information provided below is a brief reference. The service information found on KGIS including the Owner?s Manual will provide more detailed information.

IS NECESSARY TO PERFORM VARIANT CODING OF THE NEW MODULE. FOR ADDITIONAL INFORMATION RELATED TO VARIANT CODING CLICK THE VARIANT CODES LINK ON THE KGIS HOME PAGE. (SEE PAGE 2 FOR SAMPLE SCREEN SHOT.)

information regarding an inoperative, or clicking and popping noise concern from the heater box blend door.

and all Kia vehicles, after and including 2017MY, incorporate an anti-condensation logic to prevent the interior windows from becoming excessively fogged. The HVAC control head in these vehicles monitors ambient temperature to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature (about 60F or below), the anti-condensation logic may automatically set the air intake mode to FRESH, depending on the other HVAC settings. The anti-condensation logic is also designed to ensure that air intake mode is set to FRESH, as long as all conditions are met. If the user changes the air intake to RECIRCULATION, the anti-condensation logic will take control again after 5 minutes, and change the air intake mode back to FRESH. If this results in an undesired operation, the logic may be enabled or disabled by following the procedure below.

incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.

recycling, and recharging equipment. This equipment is designed to meet SAE J2843 requirements for servicing vehicles containing R1234yf refrigerant.

New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides information on setting the "Service Interval Reminder" feature available on most 2014-2023MY Kia vehicles (refer to model list on page 2). If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance. Refer to TSB ENG241 for 2023MY~ vehicles equipped with the Oil Life Management System (OLMS) feature not included in table on page 2.

asked questions regarding the Warranty Extension (WTY028).

Interval Reminder" feature available on most Kia vehicles. If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance.

letter advising them to submit the form if they had paid for repairs for this same matter prior to the warranty extension program launch.

letter advising them to submit the form if they had paid for repairs for this same matter prior to the warranty extension program launch.

regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.

operation of Multi-Function Camera (MFC) on some Kia vehicles. When normal operation is not possible due to certain outside environment conditions (such as sunlight glare, heavy rain, sunlight, snow, fog and/or substance/debris) causing a temporary concern. This stops operation causing Warning Lamp ON and/or Pop-up Message displayed on the cluster. This is a normal operation of the ADAS and once environment conditions improve and/or substance/debris are removed, the system will clear itself and operate normally.

the clock on UVO eServices (UVO 3.0) head units installed on 2017-2018MY vehicles.

on 2015 - 2017MY Soul EV (PS EV), 2016 - 2017MY K900 (KH), and 2017MY Optima Plug-in Hybrid (PHEV). It is important to note that the head units in these vehicles contain a modem and should NOT be swapped between vehicles under any circumstances. Swapping a head unit from one vehicle to another may result in a non-operational UVO eServices on one of the vehicles. If a head unit needs to be replaced, the factory recommendation is to always order a replacement head unit to ensure proper eServices operations using the new installed/replaced head unit.

separated from the antenna base on some 2016-2017MY Optima (JFa) vehicles, produced from August 25, 2015 through May 2, 2017.

REFER TO TSB TRA072A/SA317A

you last August and again last October to provide you with updates regarding news reports about non-collision fires in Kia vehicles and the status of Kia?s cooperative work with NHTSA.