2015 Kia Optima TSBs

(CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)

(CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement"; equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

test procedure of the Bearing Clearance Tester (BCT) Special Service Tool (SST). The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.

to address a no-start or hard start with poor running condition after engine replacement under PI1802Y/Z or PI1803Y/Z. Some replacement long blocks may come with pre-installed fuel rail, injectors, and injector wiring harness. If the condition is present, it is possible that the injector harness was not installed correctly. The connections may be swapped from cylinder No. 1 and cylinder No. 4, and from cylinder No. 2 and cylinder No. 3.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published PI1802 titled "Knock Sensor Detection System - ECU Logic Improvement" equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled Knock Sensor Detection System - ECU Logic Improvement equipped w/THETA II engine. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

(SC189) - This bulletin provides information on the installation of an auxiliary EVAP canister on some 2011-2015MY Optima (TF) vehicles equipped with Theta 2.4L GDI engines, produced from August 12, 2010 through July 23, 2015. This is to improve evaporative system performance and ensure compliance with Federal and California emission regulation standards.

is conducting a Voluntary Emissions Service Campaign to install an auxiliary evaporative canister in your vehicle to ensure the evaporative canister is not releasing excessive pollutants into the air.

is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2011-2015 MY Kia Optima vehicles equipped with the 2.4-liter engine manufactured from August 12, 2010 through July 23, 2015. Kia has become aware of some 2011-2015 Optima vehicles that may have been produced with evaporative canisters that can cause the vehicle to release air pollutants, which exceed Federal and California emissions standards.

is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2011-2015 MY Kia Optima vehicles equipped with the 2.4-liter engine manufactured from August 12, 2010 through July 23, 2015. Kia has become aware of some 2011-2015 MY Optima vehicles that may have been produced with evaporative canisters that can cause the vehicle to release air pollutants that exceed Federal and California emissions standards.

revised to include additional information. - This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement".

revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement".

been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

- SUPERSEDED BY PI1802YZ/1803YZ.

to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

BY PI1802Y/Z.

revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802 Rev 10, 03/16/2020) titled Knock Sensor Detection System - ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

bulletin has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

to include additional information.This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (DTC), P1326.

is conducting an important Product Improvement Campaign to perform a software update on some 2014 MY Optima vehicles equipped with 2.4L Gasoline Direct Injection ("GDI") engines, and all 2015-2018 MY Optima vehicles equipped with 2.4L GDI and 2.0L Turbocharged GDI ("T-GDI") engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").

bulletin has been revised to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled '"Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage. The KSDS detects vibrations indicating the onset of excessive connecting rod bearing wear. It is designed to alert the driver at an early stage of bearing wear before the occurrence of severe engine damage, including engine failure. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Limp Home Mode. This will reduce further damage to the engine and ensure that the vehicle occupants are not exposed to the risk of a more severe engine failure. At that time, Diagnostic Trouble Code (DTC) P1326, specific to the KSDS, will be recorded in the ECU. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed. Also, engine RPMs will be limited to approximately 1800-2000 RPM.

is conducting an important Product Improvement Campaign to perform a software update on some 2014 MY Optima vehicles equipped with 2.4L Gasoline Direct Injection ("GDI") engines, and all 2015-2018 MY Optima vehicles equipped with 2.4L GDI and 2.0L Turbocharged GDI ("T-GDI") engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").

This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on the Kia models listed on the chart below with a column mounted C-MDPS unit.

related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.

related to an expanded diagnostic test that is now required on a number of vehicles previously diagnosed with Diagnostic Trouble Code ("DTC") P1326. Using the procedures published in TSB PI1802W/X and PI1803W/X, the subject vehicles were diagnosed and determined to require an engine replacement and are currently being held at dealers pending repair. As a result of additional field data collection and analysis, the initial diagnosis method has been updated to improve test result accuracy. Prior to performing an engine replacement on any of the VINs affected by this Service Action, the engine condition needs to be re-assessed utilizing an updated/expanded diagnostic process.

Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code ("DTC"), P1326.

to include additional information This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 6, 01/31/2019) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326..

to include additional information. This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 5, 12/20/2018) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.

revised to include additional information.This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

This bulletin provides information relating to all Kia vehicles equipped with Gasoline Direct Injection (GDI) engines. In these engines highly pressurized gasoline is injected via a common fuel rail and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional Multi-Point Fuel Injection (MPI) engine, the gasoline is injected into the intake port of each cylinder at a relatively low pressure. Due to high fuel pressure in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specifications for the GDI fuel system components.

This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor and/or Electronic Control Unit (ECU) on the listed Kia models with a column mounted C-MDPS unit.

This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage

has been revised to include additional information. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage

This bulletin provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 2, 09/24/2018) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.

Driven Power Steering (MDPS) Motor and/or Electronic Control Unit (ECU) on the listed Kia models with a column mounted C-MDPS unit. Follow the procedure outlined in this bulletin.

provides information related to the Technical Service Bulletin previously published in July 2018 (PI1802, Rev 2, 09/24/2018) titled ?Knock Sensor Detection System - ECU Logic Improvement?. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below returns to the dealer with Diagnostic Trouble Code (?DTC?), P1326.

is conducting a Voluntary Emissions Service Campaign to replace the Vehicle Emission Control Information (VECI) Label on all 2015, 2016, and some 2017 MY Optima Hybrid vehicles.

is conducting a Voluntary Emissions Service Campaign to replace the Vehicle Emission Control Information (VECI) Label on all 2015, 2016, and some 2017 MY Optima Hybrid vehicles produced from July 24, 2014 through June 12, 2017, and on some 2018 MY Stinger rear-wheel drive (RWD) and all-wheel drive (AWD) vehicles equipped with Theta 2.0-T engines, produced from September 29, 2017 through November 20, 2017. An incorrect VECI label was installed during the production of these vehicles. The VECI label is extremely important when performing maintenance, emissions inspection, or ordering engine and engine management related parts. It also contains the code that tells a testing facility which test to perform to ensure the vehicle is tested to the correct emission standard.

is conducting a Voluntary Emissions Service Campaign to replace the Vehicle Emission Control Information (VECI) Label on all 2015, 2016, and some 2017 MY Optima Hybrid vehicles produced from July 24, 2014 through June 12, 2017, and on some 2018 MY Stinger rear-wheel drive (RWD) and all-wheel drive (AWD) vehicles equipped with Theta 2.0-T engines, produced from September 29, 2017 through November 20, 2017. An incorrect VECI label was installed during the production of these vehicles. The VECI label is extremely important when performing maintenance, emissions inspection, or ordering engine and engine management related parts. It also contains the code that tells a testing facility which test to perform to ensure the vehicle is tested to the correct emission standard.

is conducting an important Product Improvement Campaign to perform a software update on some 2014 MY Optima vehicles equipped with 2.4L Gasoline Direct Injection (?GDI?) engines, and all 2015 MY Optima vehicles equipped with 2.4L GDI and 2.0L Turbocharged GDI (?T-GDI?) engines to protect the engine from excessive connecting rod bearing damage by utilizing a Knock Sensor Detection System (?KSDS?). Our records show that the KSDS software was recently installed in your vehicle and we want to thank you for your quick action. Since then, Kia has become aware that the KSDS software version installed in your vehicle has an error and requires the installation of a new corrected software.

has been conducting a Product Improvement Campaign (PI1802) to perform a software update to protect the engine from excessive connecting rod bearing damage by utilizing a Knock Sensor Detection System (?KSDS?) on certain Kia vehicles. Since the launch of this Product Improvement Campaign, Kia has become aware that the KSDS software version installed on 2014~2015 MY Optima vehicles before September 7, 2018 has an error and requires the installation of a new corrected software.

25, 2018 to perform a software update on certain vehicles with 2.4L GDI engines to alert vehicle drivers at an early stage of bearing wear to prevent severe engine damage.

bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage. This update is for: * Some 2014MY Optima (TF) vehicles equipped with 2.4L GDI engines, manufactured at KMC from August 29, 2013 through April 25, 2014; * All 2015MY Optima (TF/QF) vehicles equipped with 2.4L GDI and 2.0L Turbocharged GDI (T-GDI) engines; * All 2014-2015MY Sportage (SL) vehicles equipped with 2.4L GDI and 2.0L Turbocharged GDI (T-GDI) engines; * All 2015MY Sorento (XMa) vehicles equipped with 2.4L GDI engines, manufactured from January 3, 2014 through December 11, 2014. The KSDS detects vibrations indicating the onset of excessive connecting rod bearing wear. It is designed to alert the driver at an early stage of bearing wear before the occurrence of severe engine damage, including engine failure. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Limp Home Mode. This will reduce further damage to the engine and ensure that the vehicle occupants are not exposed to the risk of a more severe engine failure. At that time, Diagnostic Trouble Code (?DTC?) P1326, specific to the KSDS, will be recorded in the ECU. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed. Also, engine RPMs will be limited to approximately 1800-2000 RPM. Kia is requesting the completion of this Product Improvement Campaign on all affected vehicles.

is conducting an important Product Improvement Campaign to perform a software update on some 2014 MY Optima vehicles equipped with 2.4L Gasoline Direct Injection (?GDI?) engines, and all 2015 MY Optima vehicles equipped with 2.4L GDI and 2.0L Turbocharged GDI (?T-GDI?) engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (?ECU?).

update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage.

considered serviceable, and should be thoroughly cleaned and transferred to the new engine.

turbo oil feed line on some 2011-2015MY Optima (TF), produced from November 1, 2010 through August 30, 2011, 2012-2015MY Optima (QF), produced from August 31, 2011 through October 2, 2015, and 2011-2015MY Sportage (SL) vehicles, produced from December 30, 2010 through November 6, 2015, equipped with Theta 2.0T-GDI engine, which may exhibit an oil leak at the turbo oil feed line.

for some 2012~2015MY Optima (QF) vehicles, produced from August 12, 2011 to October 2, 2015, some 2012~2015MY Sorento (XMa) vehicles, produced from April 19, 2011 to December 11, 2014, some 2011~2015MY Optima (TF) vehicles, produced from August 12, 2010 to July 23, 2015, and some 2014~2016MY Sportage (SL) vehicles, produced from September 30, 2013 to November 16, 2015, which may experience a malfunction indicator lamp (MIL) illuminated with the Electronic Control Unit (ECU) system-related DTC(s): P0420 and possibly P0171. This concern occurs most commonly during prolonged engine braking while descending a steep grade.

replace the crankshaft pulley and crankshaft bolt on some 2015MY Optima (QF) and 2015MY Sorento (XMa) vehicles, produced from June 30, 2014 through July 14, 2014 and equipped with 2.4L Theta engines.

outlined below to access the Dealer Engineering mode and perform various eServices related maintenance functions.

for some 2012~2015MY Optima (QF) vehicles, produced from August 12, 2011 to October 2, 2015, some 2012~2015MY Sorento (XMa) vehicles, produced from April 19, 2011 to December 11, 2014, some 2011~2015MY Optima (TF) vehicles, produced from August 12, 2010 to July 23, 2015, and some 2014~2016MY Sportage (SL) vehicles, produced from September 30, 2013 to November 16, 2015, which may experience a malfunction indicator lamp (MIL) illuminated with the Electronic Control Unit (ECU) system-related DTC(s): P0420 and possibly P0171. This concern occurs most commonly during prolonged engine braking while descending a steep grade.

with a 2.4L GDI engine, it is important to note that the DTC may recur after replacement of any faulty component(s) and resetting adaptive values. See this Article for information on resetting cylinder balance adaptation values.

the features in their recently purchased 2015MY Optima (QF) vehicle; Kia Motors America would like all dealership service personnel to be familiar with the technology highlights outlined in this TSB to help maximize owner satisfaction with their new Kia vehicle.

system is the placement of each fuel injector directly into the engine cylinder head assembly. Therefore, it is completely normal for the combustion process to create deposits on the injector spray tip surfaces.

IS CONDUCTING A VOLUNTARY EMISSIONS SERVICE CAMPAIGN / WARRANTY EXTENSION PROGRAM REGARDING THE EVAPORATIVE CANISTER IN YOUR VEHICLE.

IS CONDUCTING A VOLUNTARY EMISSIONS SERVICE CAMPAIGN / WARRANTY EXTENSION PROGRAM TO INSPECT THE EVAPORATIVE CANISTER. KIA HAS DETERMINED THAT THE FOLLOWING KIA VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN STATES WHERE HEAVY AMOUNTS OF ROAD SALT ARE USED, MAY EXHIBIT AN EVAPORATIVE CANISTER LEAK DUE TO PROLONGED EXPOSURE TO ROAD SALT

IS CONDUCTING A VOLUNTARY EMISSIONS SERVICE CAMPAIGN / WARRANTY EXTENSION PROGRAM TO INSPECT THE EVAPORATIVE CANISTER. KIA HAS DETERMINED THAT THE FOLLOWING KIA VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN STATES WHERE HEAVY AMOUNTS OF ROAD SALT ARE USED, MAY EXHIBIT AN EVAPORATIVE CANISTER LEAK DUE TO PROLONGED EXPOSURE TO ROAD SALT

SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.

WHICH MONITORS AND PREVENTS THE SIMULTANEOUS ACTIVATION OF ACCELERATOR AND BRAKE PEDALS. WHEN ENGAGED, THE FEATURE REDUCES ENGINE POWER TO IDLE. MOST CUSTOMERS WILL NEVER NOTICE THE SMART PEDAL FEATURE WHEN ACTIVE, HOWEVER, CUSTOMERS WHO TEND TO REST THEIR FOOT ON THE BRAKE PEDAL WHILE DRIVING MIGHT DESCRIBE A HESITATION OR DELAY SYMPTOM AND NOT REALIZE THAT THE EMS ELECTRONIC CONTROL MODULE IS INTERVENING, AS DESIGNED.

LOGIC FOR THE MOTOR DRIVEN POWER STEERING (MPDS) ECU OF SOME 2014~2015MY OPTIMA (QF) VEHICLES, PRODUCED FROM AUGUST 23, 2013 THROUGH JULY 24, 2014, TO ADDRESS SOME COMPLAINTS THAT THE STEERING PULLS TO ONE SIDE. TO INSTALL THE NEW STEERING LOGIC, REPROGRAM THE MDPS SYSTEM USING THE GDS/KDS DOWNLOAD, AS DESCRIBED IN THIS BULLETIN. FOR CONFIRMATION THAT THE LATEST REFLASH HAS BEEN DONE TO A VEHICLE YOU ARE WORKING ON, VERIFY ROM ID USING THE TABLES IN THIS TSB.

EXTRACTING IN USE PERFORMANCE TRACKING EMISSIONS DATA FROM THE ENGINE CONTROL UNIT (ECU) OF CERTAIN VEHICLES SOLD IN CALIFORNIA. THE CALIFORNIA AIR RESOURCES BOARD (CARB) REQUIRES THE EMISSIONS DATA FROM VEHICLES WITH A MINIMUM OF 3,000 ACCUMULATED MILES WITHOUT REPROGRAMMING OR RESETTING. TO FACILITATE COLLECTION OF THIS DATA AT THE DEALER LEVEL, GDS/KDS SCREENSHOTS WILL ALLOW THE CAPTURE OF RELEVANT PARAMETERS.

PROPER ENGINE OIL GRADE / VISCOSITY TO BE USED WHEN SERVICING VEHICLES EQUIPPED WITH A TURBOCHARGER. IN ADDITION TO FOLLOWING THE TURBO-SPECIFIC MAINTENANCE INTERVAL SCHEDULES, IT IS VERY IMPORTANT TO FOLLOW THE GRADE AND THE SAE OIL VISCOSITY RECOMMENDATIONS IN THE APPLICABLE SERVICE MANUAL TO ENSURE THE PROPER LUBRICATION IS DELIVERED TO THE TURBOCHARGER AND TO PREVENT ENGINE DAMAGE.

IS PLEASED TO ANNOUNCE THE LAUNCH OF AN ALL-NEW PRE-DELIVERY INSPECTION (PDI) AND OWNER DELIVERY FOLDER PROGRAM WHICH HAS BEEN REDESIGNED TO IMPROVE INITIAL VEHICLE QUALITY DURING PDI AND ALSO DURING DELIVERY TO YOUR CUSTOMER

MODEL ALL. NO YEARS LISTED. *PE

OR HAVE ENGINE NOISES COMING FROM FRONT CRANKSHAFT PULLEY DUE TO EXCESSIVE MATERIAL ON TIP OF CRANKSHAFT. MODEL 2015 OPTIMA, SORENTO. *PE UPDATED 03/27/15 *LJ

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure for upgrading the UVO system on some 2014~2016MY Soul (PS), Sorento (XMa), Optima (TF/QF), Forte (YD) and Sportage (SL) vehicles to address "Incoming ring volume too loud" complaints when using certain smartphones (non-iPhone). Additionally, in 2014MY vehicles the upgrade will also improve Bluetooth connectivity and voice recognition.

This bulletin provides the procedure to upgrade the UVO software on some 2015MY Soul (PS), Sportage (SL), Optima (TF, QF), Forte (YD), and Sorento (XMa) vehicles to incorporate Bluetooth and Voice Recognition improvements.

This bulletin provides the procedure to upgrade the audio software on some 2015MY Soul (PS), Sportage (SL), Optima (TF, QF), Forte (YD), and Sorento (XMa) vehicles to incorporate Bluetooth and Voice Recognition improvements.

identify and record the head unit software level on various head unit platforms and generations.

(ELE091) (Rev 1) - This bulletin provides the procedure on how to identify and record the head unit software level on various head unit platforms and generations. This procedure will now be required when ordering head units through the Direct Exchange Program (see Parts Bulletin 91-961-0005).

?Unable to connect to UVO eServices using an iPhone?, * ?Connection Error and unable to sync with the UVO App with my iPhone 7?

Sorento (XMa)/(UMa), Optima (TF HEV), Forte (YD), Sportage (SL), 2015-2016MY Sedona (YP), and 2014-2015(MY) Optima (QF/TF) vehicles to address ?Incoming ring volume too loud? complaints when using certain smartphones (non-iPhone). Additionally, in 2014MY vehicles the upgrade will also improve Bluetooth connectivity and Voice Recognition (VR).

2015MY Soul (PS), Sportage (SL), Optima (TF, QF), Forte (YD), and Sorento (XMa) vehicles to incorporate Bluetooth and Voice Recognition improvements.

some 2015MY Soul (PS), Sportage (SL), Optima (TF, QF), Forte (YD), and Sorento (XMa) vehicles to incorporate Bluetooth and Voice Recognition improvements.

navigation system software of some Sedona (YP), Soul (PS) and Optima (QF) vehicles to resolve concerns related to no sound coming from the head unit after ending a Bluetooth call.

Download Center, and other new UVO features, comes the addition of Wi-Fi capability for the vehicle. Beginning with UVO eServices w/Premium Navigation equipped 2015MY Optima (QF) vehicles, you can now connect your vehicle to a personal hotspot, such as a standalone MiFi device or a smartphone, when configured as a hotspot.

ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.

COMPATIBILITY ISSUES BETWEEN NAVIGATION HEAD UNITS AND SD CARDS WHEN REPLACING HEAD UNITS FOR MULTIMEDIA ISSUES. IF AFTER REPLACING A NAVIGATION HEAD UNIT THE ORIGINAL SD CARD DOES NOT OPERATE CORRECTLY, FOLLOW THE STEPS BELOW TO DIAGNOSE THE ISSUE:

BLUETOOTH CONCERNS WHEN USING AN IPHONE WITH IOS 8.X (IOS 8, 8.0.1, 8.0.2, 8.1, 8.1.2, 8.1.3, ETC.) WHILE PAIRED TO A HEAD UNIT.

COMPLAINTS ON AVN 4.0 (UVO ESERVICES W/PREMIUM NAVIGATION HEAD UNIT) EQUIPPED VEHICLES REGARDING THE FOLLOWING CONCERNS: H UNABLE TO ACTIVATE ESERVICES OR UNABLE TO SEND DATA FROM HEAD UNIT H MESSAGE THE CONNECTED DEVICE DOES NOT SUPPORT UVO ESERVICES FEATURES DISPLAYING ON THE HEAD UNIT SCREEN. H OR ,IN SOME CASES, AFTER RECENTLY APPLYING TSB ELE 066 TO THE 2014MY SOUL (PS) TO ADD ESERVICES FUNCTIONALITY. "

COMPLAINTS ON AVN 4.0 (NAVIGATION HEAD UNIT) RELATING TO: * MODE SWITCHES TO AM (USUALLY FROM SIRIUSXM , FM, CD, OTHER MEDIA MODE OR FROM NAVIGATION) AFTER STARTUP. * PREPARING SIRIUS IS SHOWN ON THE DISPLAY PRIOR TO THE UNIT SWITCHING TO AM. * ISSUE BEGAN AT THE START OF THE NEW YEAR (AFTER JANUARY 1ST, 2015).

ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.

THAT HAVE A SPECIFIC ERROR DISPLAYED ON THE NAVIGATION HEAD UNIT (SHOWN BELOW) AFTER PURCHASING AND INSTALLING A VERSION 8.5 MAP UPDATE SD CARD. A TOTAL OF 129 AFFECTED SD CARDS WERE PURCHASED BY CUSTOMERS THROUGH KIA DEALERS, FROM JANUARY 1ST TO MAY 11TH, 2015.

AUDIO SYSTEM SOFTWARE TO INCLUDE ANDROID AUTO AND APPLE CARPLAY SOFTWARE.

RECORD THE HEAD UNIT SOFTWARE LEVEL ON VARIOUS HEAD UNIT PLATFORMS AND GENERATIONS. THIS PROCEDURE WILL NOW BE REQUIRED WHEN ORDERING HEAD UNITS THROUGH THE DIRECT EXCHANGE PROGRAM.

UVO SYSTEM ON SOME 2014~2016MY SOUL (PS), SORENTO (XMA)/(UMA), OPTIMA (TF HEV), FORTE (YD), SPORTAGE (SL) 2015~2016MY SEDONA (YP), AND 2014-2015(MY) OPTIMA (QT/TF) VEHICLES TO ADDRESS INCOMING RING VOLUME TOO LOUD COMPLAINTS WHEN USING CERTAIN SMARTPHONES (NON-IPHONE). ADDITIONALLY, IN 2014MY VEHICLES THE UPGRADE WILL ALSO IMPROVE BLUETOOTH CONNECTIVITY AND VOICE RECOGNITION (VR). FOR VEHICLES NOT ON THE AFFECTED VEHICLES LIST, BUT WITH A CUSTOMER CONCERN AS DESCRIBED ABOVE, PERFORM THE FOLLOWING PROCEDURE OUTLINED IN THIS BULLETIN AND SUBMIT A WARRANTY CLAIM PER "CUSTOMER CONCERN" (STANDARD TSB) CLAIM INFORMATION ON PAGE 10.

REPLACEMENT OF THE SHARK-FIN STYLE ROOF ANTENNA OF SOME 2014~2016MY SPORTAGE (SL) VEHICLES, PRODUCED FROM AUGUST 1, 2014 THROUGH AUGUST 31, 2015, AND SOME 2014~2015MY OPTIMA (QF) VEHICLES, PRODUCED FROM AUGUST 1, 2013 THROUGH AUGUST 22, 2015, WHICH MAY EXHIBIT SIRIUS AUDIO RECEPTION CONCERNS (SEE SAMPLE COMPLAINTS BELOW). FOLLOW THE PROCEDURE OUTLINED IN THIS BULLETIN TO REPLACE THE ROOF ANTENNA AND CORRECT THE CONCERN.

UVO SYSTEM ON SOME 2014~2016MY SOUL (PS), SORENTO (XMA), OPTIMA (TF/QF), FORTE (YD) AND SPORTAGE (SL) VEHICLES TO ADDRESS INCOMING RING VOLUME TOO LOUD COMPLAINTS WHEN USING CERTAIN SMARTPHONES (NON-IPHONE). ADDITIONALLY, IN 2014MY VEHICLES THE UPGRADE WILL ALSO IMPROVE BLUETOOTH CONNECTIVITY AND VOICE RECOGNITION. FOR VEHICLES NOT ON THE AFFECTED VEHICLES LIST, BUT WITH A CUSTOMER CONCERN AS DESCRIBED ABOVE, PERFORM THE FOLLOWING PROCEDURE OUTLINED IN THIS BULLETIN AND SUBMIT A WARRANTY CLAIM PER "CUSTOMER CONCERN" (STANDARD TSB) CLAIM INFORMATION ON PAGE 10.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2011-2015MY Optima (TF), 2012-2015MY Optima (QF) and 2016-2020MY Optima (JF, JFa) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.

COMPATIBILITY (CS2310) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 7. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2011-2015MY Optima (TF), 2012-2015MY Optima (QF) and 2016-2020MY Optima (JF, JFa) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

COMPATIBILITY (CS2310) - This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 6. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2011-2015MY Optima (TF), 2012-2015MY Optima (QF) and 2016-2020MY Optima (JF, JFa) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2011-2015MY Optima (TF), 2012-2015MY Optima (QF) and 2016-2020MY Optima (JF, JFa) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2011-2015MY Optima (TF), 2012-2015MY Optima (QF) and 2016-2020MY Optima (JF, JFa) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

information associated with the "Hybrid System Warranty Extension Program" (WTY029) to inspect and, if necessary, replace the High Voltage Battery (HVB) Safety Plug Fuse Assembly or Main Fuse on 2013-2016MY Optima Hybrid (TF HEV) vehicles produced from September 27, 2012 through July 22, 2015.

USB ports and 12V power outlets to connect/charge mobile phones. Customers may experience issues with their head units that may be related to the use of aftermarket USB charging cables, including; * Electrical interference and limited or no functionality when attempting to play music, or when charging a device through the USB port * Excessive static or noise when listening to the audio source * Malfunctions and screen freeze of the head unit screen * Slow down of the system response while device is plugged in * Music will not play from iPhone 5 or 6 with Kia iPod cable and aftermarket adapter * No or limited functionality when trying to play music from an Apple device

The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.

vehicles with Blind Spot Detection (BSD), which may exhibit a ?Check BSD System? message and no communication with the BSD system after collision repairs. This concern is commonly caused by the rear bumper harness installed backwards.

TO 2014-2015MY OPTIMA (QF) VEHICLES WITH BLIND SPOT DETECTION (BSD), WHICH MAY EXHIBIT A CHECK BSD SYSTEM MESSAGE AND NO COMMUNICATION WITH THE BSD SYSTEM AFTER COLLISION REPAIRS. THIS CONCERN IS COMMONLY CAUSED BY THE REAR BUMPER HARNESS INSTALLED BACKWARDS.

SOME VEHICLES EQUIPPED WITH BLIND SPOT DETECTION (BSD), WHICH MAY EXHIBIT A CHECK BSD SYSTEM MESSAGE WITH DTCS: C270254 AND C270354: C270254: CONTROL MODULE MASTER MISSING CALIBRATION / C270354: CONTROL MODULE SLAVE MISSING CALIBRATION

THIS SPECIAL SERVICE TOOL (SST) WAS DEVELOPED TO IMPROVE THE EFFICIENCY AND EFFECTIVENESS OF UPDATING 2010MY, AND LATER, KIA AUDIO HEAD UNITS USING A GDS, AND NOW, THE SAME FUNCTIONALITY IS AVAILABLE ON KDS. SOME TECHNICIANS MAY NOT BE AWARE OF THE BENEFITS THE AUM TOOL HAS TO OFFER. THE AUM ELIMINATES THE NEED FOR MULTIPLE USB FLASH DRIVES FOR SPECIFIC VEHICLE MODELS AND APPLICATIONS WHICH, IF MISAPPLIED, MAY RESULT IN AN IMPROPER AUDIO SYSTEM SOFTWARE UPDATE AND/OR LOCKED UP HEAD UNIT. ADDITIONALLY, FIELD REPORTS HAVE INDICATED THAT USB DRIVES FOR AUDIO UPDATES ARE EASILY LOST OR MISPLACED.

MODULE ASSEMBLY ON CERTAIN 2014~2015MY OPTIMA (QF) VEHICLES, PRODUCED FROM MARCH 1, 2014 THROUGH JULY 31, 2014, WHICH MAY EXHIBIT AN INOPERATIVE POWER WINDOW. KIA IS REQUESTING THE COMPLETION OF THIS SERVICE ACTION ON ALL AFFECTED VEHICLES, INCLUDING DEALER STOCK, PRIOR TO DELIVERY. BEFORE CONDUCTING THE PROCEDURE, VERIFY THE VEHICLE IS INCLUDED IN THE LIST OF AFFECTED VINS.

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

This bulletin provides the procedure to replace the steering gear box yoke plug and assembly on some models listed below, which may exhibit a ticking noise while turning the steering wheel with the vehicle stopped. This condition is caused by a worn lining on the steering gear box yoke assembly.

This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.

This bulletin provides the procedure to replace the steering gear box yoke plug and assembly on some models listed below, which may exhibit a ticking noise while turning the steering wheel with the vehicle stopped. This condition is caused by a worn lining on the steering gear box yoke assembly. Follow the procedure outlined in this bulletin to replace the steering gear box yoke plug and assembly with updated parts.

yoke plug and assembly on some models listed below, which may exhibit a ticking noise while turning the steering wheel with the vehicle stopped. This condition is caused by a worn lining on the steering gear box yoke assembly. Follow the procedure outlined in this bulletin to replace the steering gear box yoke plug and assembly with updated parts.

This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.

related to the Smart Key Systems on vehicles equipped with A/T (automatic transaxle) and Start/Stop Buttons (SSB).

Damper Clutch (D/C) Solenoid on 6-speed automatic transaxles with DTC P0741 (active or history), instead of replacing the transaxle. To reduce vehicle repair time, this procedure can be performed with the transaxle installed in the vehicle.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

RELEARN THE ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE ECM/PCM.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE PCM/TCM. AFTER THE ADAPTIVE VALUES ARE RESET, THE TRANSMISSION COMPUTER ADAPTIVE VALUES MUST BE RELEARNED BY DRIVING IN A PRECISE MANNER TO TEACH THE COMPUTER THE PROPER SOLENOID DUTY AND LINE PRESSURE FOR THE NEW TRANSMISSION/COMPUTER COMBINATION.

provides the procedure to perform an evaporative leak test and replace the Fuel Tank Air Filter, and, if necessary, the Natural Vacuum Leak Detector (NVLD) on some 11-16MY Kia vehicles listed in the table below, which may experience an evaporative leak concern with DTC P0456.

illuminated with DTC(s) P0442, P0455, P0456, or P0457 (Evaporative Emissions System-Leak detected) and the evaporative (EVAP) leak self-test resulted in NTF, a manual EVAP test is recommended.

provides information to inspect and/or replace the evaporative canister assembly on some Optima (TF) vehicles, produced from September 2, 2010 through November 29, 2014, some Optima Hybrid (TF HEV) vehicles, produced from February 15, 2011 through November 29, 2014, some Rondo (UN) vehicles, produced from April 1, 2009 through July 30, 2010, and some Sedona (VQ) vehicles, produced from April 1, 2009 through June 17, 2014. The subject vehicles originally sold or currently registered in one of twenty-eight (28) salt belt states may experience a leak detection warning of the evaporative emission systems, along with DTC(s) P0442 or P0455. For vehicles originally sold or currently registered in one of the twenty-eight (28) salt belt states, (AK, CT, DC, DE, IA, IL, IN, MA, MD, ME, MI, MN, MO, NH, NJ, NY, OH, PA, RI, VT, WI, WV, KS, KY, NE, ND, SD and UT), the evaporative canister will be inspected, and if no leak is found, the mounting bracket will be replaced with a new improved part. If a crack in the evaporative canister is found, the canister will be replaced with a new improved part. Before conducting the procedure, verify the vehicle is included in the list of affected VINs. For vehicles in other states, Kia is extending the warranty on the evaporative canister from 5 years/60,000 miles to 10 years/120,000 miles, whichever occurs first starting from the date of first service. Follow the procedures outlined in this bulletin to resolve the concern.

Emissions System ? Small Leak Detected), and an inspection of the vapor lines, connections and fuel cap reveal no abnormalities, closely inspect the mounting holes of the charcoal canister for visible cracks.

PROVIDES INFORMATION TO INSPECT AND/OR REPLACE THE EVAPORATIVE CANISTER ASSEMBLY ON SOME OPTIMA (TF) VEHICLES, PRODUCED FROM SEPTEMBER 2, 2010 THROUGH NOVEMBER 29, 2014, SOME OPTIMA HYBRID (TF HEV) VEHICLES, PRODUCED FROM FEBRUARY 15, 2011 THROUGH NOVEMBER 29, 2014, SOME RONDO (UN) VEHICLES, PRODUCED FROM APRIL 1, 2009 THROUGH JULY 30, 2010, AND SOME SEDONA (VQ) VEHICLES, PRODUCED FROM APRIL 1, 2009 THROUGH JUNE 17, 2014. THE SUBJECT VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN ONE OF TWENTY-EIGHT (28) SALT BELT STATES MAY EXPERIENCE A LEAK DETECTION WARNING OF THE EVAPORATIVE EMISSION SYSTEMS, ALONG WITH DTC(S) P0442 OR P0455. FOR VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN ONE OF THE TWENTY-EIGHT (28) SALT BELT STATES, (AK, CT, DC, DE, IA, IL, IN, MA, MD, ME, MI, MN, MO, NH, NJ, NY, OH, PA, RI, VT, WI, WV, KS, KY, NE, ND, SD AND UT), THE EVAPORATIVE CANISTER WILL BE INSPECTED, AND IF NO LEAK IS FOUND, THE MOUNTING BRACKET WILL BE REPLACED WITH A NEW IMPROVED PART. IF A CRACK IN THE EVAPORATIVE CANISTER IS FOUND, THE CANISTER WILL BE REPLACED WITH A NEW IMPROVED PART. BEFORE CONDUCTING THE PROCEDURE, VERIFY THE VEHICLE IS INCLUDED IN THE LIST OF AFFECTED VINS. FOR VEHICLES IN OTHER STATES, KIA IS EXTENDING THE WARRANTY ON THE EVAPORATIVE CANISTER FROM 5 YEARS/60,000 MILES TO 10 YEARS/120,000 MILES, WHICHEVER OCCURS FIRST STARTING FROM THE DATE OF FIRST SERVICE. FOLLOW THE PROCEDURES OUTLINED IN THIS BULLETIN TO RESOLVE THE CONCERN.

COMPLAIN ABOUT WATER DROPLETS FORMING INSIDE THE REAR TAIL LAMP LENSES FOLLOWING A RAINSTORM OR AFTER WASHING THEIR VEHICLE. THESE WATER DROPLETS ARE MORE VISIBLE AT NIGHT AND THE QUANTITY OF WATER PRESENT IS MORE THAN JUST A THIN FILM OF CONDENSATION WHICH MAY NOT EASILY EVAPORATE. THIS CONCERN IS CAUSED BY A GAP BETWEEN THE TAIL LAMP HOUSING GASKET AND VEHICLE BODY WHICH ALLOWS WATER TO INFILTRATE INTO THE TAIL LAMP. TO RESOLVE THIS CONCERN, ORDER ADDITIONAL FOAM GASKETS (ONE ADDITIONAL PER SIDE) AND INSTALL THEM BETWEEN THE LEFT AND RIGHT TAIL LAMPS AND THE BODY OF THE VEHICLE, AS OUTLINED BELOW.

REAR TAIL LAMPS ON 2014-2015MY OPTIMA (QF) VEHICLES, WHEN EITHER OF THE LAMP HOUSINGS MAY INDICATE WATER INSIDE. ON SOME 2014-2015MY OPTIMA (QF) VEHICLES, CUSTOMERS MAY COMPLAIN ABOUT WATER DROPLETS FORMING INSIDE THE REAR TAIL LAMP HOUSING FOLLOWING A RAINSTORM OR AFTER WASHING THEIR VEHICLE. THESE WATER DROPLETS ARE MORE VISIBLE AT NIGHT AND THE QUANTITY OF WATER PRESENT IS MORE THAN JUST A THIN FILM OF CONDENSATION, WHICH MAY NOT EASILY EVAPORATE. THIS CONCERN IS CAUSED BY A GAP BETWEEN THE TAIL LAMP HOUSING SEAL AND VEHICLE BODY, WHICH ALLOWS WATER TO INFILTRATE INTO THE TAIL LAMP. TO RESOLVE THIS CONCERN, ORDER ADDITIONAL FOAM GASKETS AND INSTALL THEM BETWEEN THE LEFT AND RIGHT TAIL LAMPS AND THE BODY OF THE VEHICLE, AS OUTLINED BELOW. TO ENHANCE CUSTOMER SATISFACTION, THIS BULLETIN OUTLINES THE INSTALLATION AND REPAIR OF BOTH SIDES (LEFT AND RIGHT) OF THE VEHICLE, EVEN WHEN ONLY ONE SIDE IS AFFECTED. "

FUEL INJECTORS IN SOME SORENTO (XMA) PRODUCED 12/17/2012~12/11/2014, OPTIMA (QF) PRODUCED 07/28/2013~10/02/2015, OPTIMA (TF) PRODUCED 09/09/2013~07/23/2015 2014~2015MY, AND SPORTAGE (SL) PRODUCED 09/01/2013~12/01/2014, WHICH MAY EXHIBIT A MALFUNCTION INDICATOR LAMP (MIL) ON ALONG WITH DTCS P0263, P0266, P0269 AND/OR P0272. FOLLOW THE PROCEDURE OUTLINED IN THIS BULLETIN TO DIAGNOSE AND REPLACE THE AFFECTED INJECTOR TO CORRECT THE CONCERN.

relating to the vehicles listed below with Blind Spot Detection (BSD), which may exhibit a ?Check BSD System? message and no communication with the BSD system after collision repairs.

2014-2015MY Optima (QF) and replace the front and if necessary, the rear emblems on some 2014-2015MY Sorento (XMa) vehicles, which may exhibit peeling or delamination of the emblem coating. Follow the procedures outlined in this bulletin to correct the concern of peeling or delaminating emblems.

diagnosis of the Inhibitor Switch.

VEHICLES, A CUSTOMER MAY EXPERIENCE AN INTERMITTENT NO START CONCERN, ON COLD START-UP AND IN COOLER TEMPERATURES. THIS CONCERN MAY ALSO BE ACCOMPANIED BY A COMPLAINT OF THE CHECK BSD SYSTEM MESSAGE (A) APPEARING ON THE INSTRUMENT CLUSTER (FOR VEHICLES EQUIPPED WITH BLIND SPOT DETECTION (BSD) SYSTEM) ALONG WITH A LACK OF PARK (P) INDICATION IN THE CLUSTER (B). THIS CONCERN MAY BE RELATED TO AN INTERNAL CONNECTION/CONTACT CONCERN IN THE INHIBITOR SWITCH (C) AND WILL BE DIFFICULT TO DUPLICATE IN A WARM SHOP ENVIRONMENT.

*LJ

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the repair procedure for the Integrated Brake Actuation Unit (iBAU) system on some 2014-2019MY EV/Hybrid/Plug-In Hybrid vehicles listed (see table), which may exhibit a "honking" (Hissing) noise due to air remaining in the brake fluid system.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

combination lamp pads on some 2011-2015MY Optima (TF), produced from August 12, 2010 through July 23, 2015, and some 2011-2016MY Optima (TF HEV) vehicles, produced from February 15, 2011 through July 22, 2015, which may exhibit evidence of water intrusion in the outside rear combination lamps.

once fully attached, are utilized in various Kia models and are strictly intended for ?one time use.? Some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.? It is critical for technicians to be aware that ALL such locking fasteners, regardless of type, are for ?one time use? only.

strictly intended for ?one time use?. Though not limited to the following, some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.?

IS NECESSARY TO PERFORM VARIANT CODING OF THE NEW MODULE. FOR ADDITIONAL INFORMATION RELATED TO VARIANT CODING CLICK THE VARIANT CODES LINK ON THE KGIS HOME PAGE. (SEE PAGE 2 FOR SAMPLE SCREEN SHOT.)

INTERMITTENT SQUEAL WHEN COMING TO A STOP. THIS CONCERN IS OFTEN DUE TO THE BRAKE PADS NOT FREELY FLOATING WITHIN THE CALIPER AND STICKING TO THE CALIPER BRACKET. THIS CONDITION MAY LEAD TO A VIBRATION AND NOISE WHICH IS HEARD DURING THE LAST PORTION OF BRAKE PEDAL TRAVEL, BEFORE COMING TO A COMPLETE STOP.

crossmember on some 2012-2015MY Optima (QF) vehicles, equipped with panorama sunroof, produced from August 31, 2011 through September 22, 2015, which may experience a slight creaking or rattle noise at the sunroof area.

EXTERIOR DOOR HANDLE TRIM CAP OF SOME 2015MY OPTIMA (QF) VEHICLES, PRODUCED FROM SEPTEMBER 2, 2014 THROUGH AUGUST 24, 2015, WHICH MAY EXPERIENCE AN INOPERATIVE DRIVERS SIDE EXTERIOR DOOR HANDLE. KIA IS REQUESTING THE COMPLETION OF THIS SERVICE ACTION ON ALL AFFECTED VEHICLES, INCLUDING DEALER STOCK, PRIOR TO DELIVERY.

SOME 2014~2015MY SPORTAGE (SL), FORTE (YD), OPTIMA (TF/QF), OPTIMA HYBRID (TF HEV) AND SORENTO (XMA) VEHICLES, WHICH MAY EXHIBIT AN INOPERATIVE UVO MEDIA BUTTON.

SOME 2014~2015MY SPORTAGE (SL), FORTE (YD), OPTIMA (TF/QF), OPTIMA HYBRID (TF HEV) AND SORENTO (XMA) VEHICLES, WHICH MAY EXHIBIT AN INOPERATIVE UVO MEDIA BUTTON.

(EXCLUDING 2016 K900 AND SOUL EV)

regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.

article for detailed information on applicable models, model year and system supplier; along with the applicable Hotline contact information and business hours.

you last August and again last October to provide you with updates regarding news reports about non-collision fires in Kia vehicles and the status of Kia?s cooperative work with NHTSA.

TO AN UPGRADE OF THE LOGIC FOR THE BLIND SPOT DETECTION (BSD) SYSTEM OF SOME 2015MY OPTIMA (QF) VEHICLES, PRODUCED FROM AUGUST 12, 2014 TO NOVEMBER 19, 2014. THE VEHICLES IN QUESTION MAY HAVE A CHECK BSD SYSTEM MESSAGE ILLUMINATED IN THE INSTRUMENT CLUSTER, ALONG WITH DTC C270254 OR C270354 STORED IN BSD SYSTEM, AS ACTIVE OR PENDING, DURING FAULT CODE SEARCHING. TO RESOLVE THIS CONCERN, THE BSD SYSTEM SHOULD BE REPROGRAMMED USING THE GDS DOWNLOAD, AS DESCRIBED IN THIS BULLETIN. FOR CONFIRMATION THAT THE LATEST REFLASH HAS BEEN DONE TO A VEHICLE YOU ARE WORKING ON, VERIFY ROM ID USING THE TABLES IN THIS TSB.

incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.

function using the GDS.

STRUT BEARING WITH NEW PARTS YOU MAY ENCOUNTER DIFFICULTY INSTALLING THE NEW STRUT BEARING INTO PLACE ON THE INSULATOR. THIS CONDITION IS DUE TO A CHANGE IN THE DESIGN OF THE STRUT BEARING (A) WHICH RESULTS IN TIGHTER TOLERANCES BETWEEN THE BEARING AND INSULATOR. REFER TO THE PROCEDURE BELOW FOR MORE INFORMATION.

STRUT BEARING WITH NEW PARTS YOU MAY ENCOUNTER DIFFICULTY INSTALLING THE NEW STRUT BEARING INTO PLACE ON THE INSULATOR. THIS CONDITION IS DUE TO A CHANGE IN THE DESIGN OF THE STRUT BEARING (A) WHICH RESULTS IN TIGHTER TOLERANCES BETWEEN THE BEARING AND INSULATOR. REFER TO THE PROCEDURE BELOW FOR MORE INFORMATION.

Interval Reminder" feature available on most Kia vehicles. If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance.

complain of an oily substance dripping onto the driver?s side floorboard area, especially in areas with high ambient temperatures. This article provides the process to resolve by cleaning excessive amounts of grease applied applied to the steering column tilt adjustment area.

PERSONNEL MAY NOTICE THAT THE WHEEL CENTER CAP HAS A BLACK BACKGROUND AND DIFFERS IN APPEARANCE FROM OTHER OPTIMA LX VEHICLES. THIS IS NORMAL VEHICLE CONTENTING AND NO PARTS SHOULD BE REPLACED IN AN ATTEMPT TO MATCH THE APPEARANCE TO RETAIL UNITS IN DEALER INVENTORY.